Related
Installing update...
assert failed: getprop("ro.product.device") == "SCH-I800" || getprop("ro.build.product") == "SCH-I800" ||
getprop("ro.product.board") == "SCH-I800"
E:Error in/sdcard/KhasMek.DJ11.Kleanmod.v3.zip
(Status 7)
Installaiton Aborted
Can,t install rom, does anybody have some simmilar?
bombarder said:
Installing update...
assert failed: getprop("ro.product.device") == "SCH-I800" || getprop("ro.build.product") == "SCH-I800" ||
getprop("ro.product.board") == "SCH-I800"
E:Error in/sdcard/KhasMek.DJ11.Kleanmod.v3.zip
(Status 7)
Installaiton Aborted
Can,t install rom, does anybody have some simmilar?
Click to expand...
Click to collapse
Yes just search in this forum. I had the same problem too. Basically here is what to do
1- download and flash the full firmware JJ4 with pit and partition cheched (this will resolve the csc errors)
Your tab might still get stuck on the boot logo. Turn it off then go to download mode
2- Flash Gingerbread 2.3.3 following Chainfire instructions
Your tab should reboot normally.
Good luck
Sent from my GT-P1000 using XDA Premium App
I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?
bombarder said:
I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?
Click to expand...
Click to collapse
Yes gsm tab
Sent from my GT-P1000 using XDA Premium App
if I flashed it could it damage my device?I read somewhere about posibility damaging
bombarder said:
I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?
Click to expand...
Click to collapse
I actually had the same issue, and have been scouring the forums for days. Unfortunately, I wasn't able to find a solution. I tried following the instructions listed for Unbricking the Galaxy Tab and it worked for about a day.
After that it began generating errors. First my widgets disappeared saying there was a problem, second reboot wifi generated errors and wouldn't turn on, and third reboot was the Verizon Logo. When it was on the VZW logo, it would vibrate once, pause, and vibrate three times. Wash. Rinse. Repeat.
So, if this is what you were dealing with, this is what I did to resolve it. (Warning: I am not a developer, and take no responsibility for what happens should you choose to repeat my steps.)
1.) I noticed it was still on CWM3, tried to reflash Khasmek's Voodoo plus v.5. -Booted into Recovery
-Wiped Data, Cache
-Flashed
Got me out of the vzw loop. Went to boot loop.
2.) Flashed rom (tried K-lean v3 and Khasmeks Aosp and Simply Aosp.
-Copy rom to SD card.
-Boot into Recovery
-Update from Zip on SD
-Flash
Fail. Still a status 7 on install of any given rom. Still displaying CWM 3.0 after kernel flash.
3.) Heimdall with original files.
-Go look it up.
Booted, but a function died on every reboot (Camera, Wifi, Widgets, etc). Noticed that system only displayed 512 RAM. May have flashed incorrect files.
-Verified. Idiot. Downloaded and Repeated with correct files.
Still had same issue with rebooting and losing a function every time.
Still displaying CWM3.0
4.) Got frustrated. Drank a little. Remembered I had a recovery from March.
-Boot into recovery
-Backup and Restore
-Restore
Bingo. Everything seems to be functioning correctly and has been for a few days. Have rebooted multiple times, no issues. Also, CWM is 2.5 again.
Hope that helps.
Hi all,
I recently flashed an android for the first time, so go easy on me!
I flashed my galaxy note gt-n7000 with the CM10 preview #3 (dated 20th August 2012) with success... but!
When I try to install preview #4 of CM10 (24-08-1012), I always get an error message coming from the updater-script.
It says:
assert failed: getprop("ro.product.device") == "galaxynote" || getprop("ro.build.product") == "galaxynote" ||
getprop("ro.product.device") == "n7000" || getprop("ro.build.product") == "n7000" ||
getprop("ro.product.device") == "N7000" || getprop("ro.build.product") == "N7000" ||
getprop("ro.product.device") == "GT-N7000" || getprop("ro.build.product") == "GT-N7000"
I already figured out that my note's name/product/device has been changed to I9100 (S2 build), so I simply opened /system/build.prop and changed it back to GT-N7000. (settings -> about phone -> model is showing GT-N7000 as it should now). Although, I didn't change ro.build.product because the build.prop said it isn't used anymore :s
Still, while running the zip from cwm (6.0.x.x) I still get the same message and it aborts with status 7.
One thing to take notice: I can't install from SD card, it says it's unable to mount the /sdcard when I try to update from external sd card in cwm. I'm trying to install from internal sd...
I already tried installing another rom without success.
I'm in the dark here, so please light up the way :crying: :fingers-crossed:
selman555 said:
Hi all,
I recently flashed an android for the first time, so go easy on me!
I flashed my galaxy note gt-n7000 with the CM10 preview #3 (dated 20th August 2012) with success... but!
When I try to install preview #4 of CM10 (24-08-1012), I always get an error message coming from the updater-script.
It says:
assert failed: getprop("ro.product.device") == "galaxynote" || getprop("ro.build.product") == "galaxynote" ||
getprop("ro.product.device") == "n7000" || getprop("ro.build.product") == "n7000" ||
getprop("ro.product.device") == "N7000" || getprop("ro.build.product") == "N7000" ||
getprop("ro.product.device") == "GT-N7000" || getprop("ro.build.product") == "GT-N7000"
I already figured out that my note's name/product/device has been changed to I9100 (S2 build), so I simply opened /system/build.prop and changed it back to GT-N7000. (settings -> about phone -> model is showing GT-N7000 as it should now). Although, I didn't change ro.build.product because the build.prop said it isn't used anymore :s
Still, while running the zip from cwm (6.0.x.x) I still get the same message and it aborts with status 7.
One thing to take notice: I can't install from SD card, it says it's unable to mount the /sdcard when I try to update from external sd card in cwm. I'm trying to install from internal sd...
I already tried installing another rom without success.
I'm in the dark here, so please light up the way :crying: :fingers-crossed:
Click to expand...
Click to collapse
Just flash a cm10 safe kernel first before flashing rom, reboot the recovery and then flash away.
Sent From My GT-N7000 Using XDA Premium.
You missed something
sahilarora2003 said:
Just flash a cm10 safe kernel first before flashing rom, reboot the recovery and then flash away.
Sent From My GT-N7000 Using XDA Premium.
Click to expand...
Click to collapse
Sorry, but I think you missed the fact that I am already on the unofficial cm10 preview 3 rom. Meaning I already have a cm10 safe kernel?
Perhaps I am missing something too?
buildprop flash,
Or format in mounts system then reflash a rom. Thats where it is saved. I think you are on a save kernel so I think it should not be an issue.
Edit: Just to be sure you can flash a safe kernel, reboot in recovery and then do above. All at your own risk
Sent from my GT-N7000 using Tapatalk 2
Are you sure?
baz77 said:
buildprop flash,
Or format in mounts system then reflash a rom. Thats where it is saved. I think you are on a save kernel so I think it should not be an issue.
Edit: Just to be sure you can flash a safe kernel, reboot in recovery and then do above. All at your own risk
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
You're suggesting formatting /system and then reflashing another rom (without rebooting in between)?
Could that be the solution? The build.prop file can be found there, how will the updater-script be able to find the parameters it needs if the /system folder was formatted?
Sorry if it's an obvious question (which I think it is), but I'm not yet an android savvy. I've had some experience with linux tho...
Any help is appreciated!
well funny thing is, it will work, try it
Sent from my GT-N7000 using Tapatalk 2
No good!
baz77 said:
well funny thing is, it will work, try it
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
I'm not panicking, but still, I formated /system and tried flashing cm10 preview #4, but it still gives me the aser failed error.
My build.prop is GONE and still it says it can't assert... what gives?
ok then I am suspecting recovery and kernel, Can you flash a different safe kernel, and then reflash the rom?
edit, appears my case, when I had it, it must have been different. I did change kernel in similar case and it worked
Sent from my GT-N7000 using Tapatalk 2
Trying parandroid now
baz77 said:
ok then I am suspecting recovery and kernel, Can you flash a different safe kernel, and then reflash the rom?
edit, appears my case, when I had it, it must have been different. I did change kernel in similar case and it worked
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
I installed cwm 5.8 now, It seems I can't mount /emmc but i'm gonna give it a go...
Got the solution.
Downgrade to GB, root the device and upgrade to cm10 in recovery.
It will work.
Another problem...
sahilarora2003 said:
Got the solution.
Downgrade to GB, root the device and upgrade to cm10 in recovery.
It will work.
Click to expand...
Click to collapse
I tried to install speedmod K3-13, which landed me on cwm 5.8.1.8. I can't get back to 6.0.x because this version screws up the mount /emmc and /sdcard! When I choose install from /sdcard, the content that is displayed is actually my internal storage.
I can't put anything on my internal storage, because my rom doesn't work anymore and I can't connect to my pc...
I've seen the posts about downgrading to GB, but I can't because of the sdcard & emmc screwup..
Some tips & tricks would be helpful. :fingers-crossed:
good one, remember to reboot recovery after flashing kernel.
last resort try flashing a gb rom from pc odin with or without regular pitfile. Flashing takes some time so be patient. If it get stuck about an hour at factorysys you might have case of superbrick, but I am not expecting that.
Sent from my GT-N7000 using Tapatalk 2
I'll try
baz77 said:
good one, remember to reboot recovery after flashing kernel.
last resort try flashing a gb rom from pc odin with or without regular pitfile. Flashing takes some time so be patient. If it get stuck about an hour at factorysys you might have case of superbrick, but I am not expecting that.
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
Way to put my mind at ease
Do you have a link to where I can find the correct gb for odin?
selman555 said:
I tried to install speedmod K3-13, which landed me on cwm 5.8.1.8. I can't get back to 6.0.x because this version screws up the mount /emmc and /sdcard! When I choose install from /sdcard, the content that is displayed is actually my internal storage.
I can't put anything on my internal storage, because my rom doesn't work anymore and I can't connect to my pc...
I've seen the posts about downgrading to GB, but I can't because of the sdcard & emmc screwup..
Some tips & tricks would be helpful. :fingers-crossed:
Click to expand...
Click to collapse
Download prerooted GB rom from my sig.
Reboot in Download mode.
Open PC Odin on your PC
Connect your phone to pc via usb cable
Select GB file under PDA tab
Hit Start
Wait for the completion.
Thanks!
sahilarora2003 said:
Download prerooted GB rom from my sig.
Reboot in Download mode.
Open PC Odin on your PC
Connect your phone to pc via usb cable
Select GB file under PDA tab
Hit Start
Wait for the completion.
Click to expand...
Click to collapse
Alright, very good!
So afterwards, I can just reflash through cwm to cm10?
That would be awesome!
selman555 said:
Alright, very good!
So afterwards, I can just reflash through cwm to cm10?
That would be awesome!
Click to expand...
Click to collapse
Yes you can. Just reboot into recovery and flash rom+gapps, do all 3 wipes(Cache/Dalvik/Data) and reboot woaah you are on cm10 now Cheers
Fingers crossed for now...
sahilarora2003 said:
Yes you can. Just reboot into recovery and flash rom+gapps, do all 3 wipes(Cache/Dalvik/Data) and reboot woaah you are on cm10 now Cheers
Click to expand...
Click to collapse
I was on CM10 preview 3, but I just had to go to 4!!!
Especially the fact that the g-sensor didn't work bothered me!
The GB download is very slow though, i'm downloading at 80~800kb/s. It's taking for ages.
Perhaps you should find another mirror for you sig...
I'll let you know how it went
Going great!
sahilarora2003 said:
Yes you can. Just reboot into recovery and flash rom+gapps, do all 3 wipes(Cache/Dalvik/Data) and reboot woaah you are on cm10 now Cheers
Click to expand...
Click to collapse
I've gotten past the factorysys.img and it's now writing nand...
Would it be safe to go to paranoid android from here?
Should be, but follow the procedure from paranoid android thread to the letter. Its in first post of the thread, or in the thread.
selman555 said:
I've gotten past the factorysys.img and it's now writing nand...
Would it be safe to go to paranoid android from here?
Click to expand...
Click to collapse
Yes. Just reboot into recovery and flash rom+gapps and do all three wipes. Time to reboot now.
Sent From My GT-N7000 Using XDA Premium.
So I'm trying to install a ROM onto my Samsung Captivate. I've went through this process multiple times, although not with this phone. Im in CWM recovery (Version 2.x, which is probably the problem), first I realize my ext-SD won't mount. I find a simple work around and load the .zip onto my internal SD. So I try to install it again and and it it has some long error message (I'll post it on here in a few minutes), ending with "Installation aborted".
Any ideas of what I need to do? My only idea is to update recovery but I can't get around to that right now. I'm just trying to avoid anymore roadblocks.
Sent from my Desire HD using xda app-developers app
EXACTLY WHAT IT SAYS ON MY PHONE:::::
ClockwordMod Recovery v.2.5.1.0 SpeedMod ULFK
-- Installing: SDCARD:cm-10-20121004-NIGHTLY-captivatemtd.zip
Finding update package...
Opening update package...
Installing update...
assert failed: get prop("ro.product.device") == "
captivate" I I getprop("ro.build.product") == "ca
ptivate" I I
getprop("ro.product.device")
== "captivatemtd" I I getprop("ro.build.product")
== "captivatemtd" I I
getprop("ro.product
.device") == "SGH-I896" I I getprop(ro.build.pro
duct") == "SGH-I897" I I getprop("ro.build.p
roduct") == "SGH-I897"
E:Error in /mnt/sdcard/cm-10-20121004-NIGHTLY-ca
ptivatemtd.zip
(Status 7)
Installation aborted.
That means you have a device/ Rom file mismatch. However, that seems to be in order since you say you have a captivate and you are flashing the file for captivate. Your build prop must be modified by your current Rom. Try flashing a kernel first, then redoing the installation from the new recovery.
Sent from my SGH-I777 using xda premium
Okay. Quick question, can I flash a kernel .zip using the recovery I have right now?
Sent from my Desire HD using xda app-developers app
Try loading a gingerbread stock rom that has been updated to contain cwm recovery using 1-click package(there is thread with all 1-clicks). If you never had a gb rom before then select a package with bootloader so that you'll have gb bootloader too. Then flash CM10. That should work.
Hello,
I was trying to install the Paranoid Android ROM (http://forum.xda-developers.com/showthread.php?t=2203301).
I did everything as always but unfortunately I receive an error:
Code:
CWM-based Recovery v.5.5.0.4 :: CF-v.1.5
-- Installing: /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
Finding update package...
Opening update package...
[COLOR="DarkRed"]Installing update...
assert failed: getprop("ro.product.device") == "m3" || getprop("ro.built.product") == "m3" ||
getprop("ro.product.device") == "i9305" || getprop("ro.built.product") == "i9305" ||
getprop("ro.product.device") == "GT-I9305" || getprop("ro.built.product") == "GT-I9305"
E:Error in /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
(Status 7)
Installation aborted[/COLOR]
Im not a software developer for mobile phones but I guess it is trying to tell me, that the ROM which I'm trying to install isnt working on my device.
But I am absolutely sure that I got an I9305 as you can see on the attached screenshot.
Any ideas?
I have also redownloaded the ZIP and tried it multiple times but always ended up with the same error.
I really would appreciate any help!
Celaniry said:
Hello,
I was trying to install the Paranoid Android ROM (http://forum.xda-developers.com/showthread.php?t=2203301).
I did everything as always but unfortunately I receive an error:
Code:
CWM-based Recovery v.5.5.0.4 :: CF-v.1.5
-- Installing: /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
Finding update package...
Opening update package...
[COLOR="DarkRed"]Installing update...
assert failed: getprop("ro.product.device") == "m3" || getprop("ro.built.product") == "m3" ||
getprop("ro.product.device") == "i9305" || getprop("ro.built.product") == "i9305" ||
getprop("ro.product.device") == "GT-I9305" || getprop("ro.built.product") == "GT-I9305"
E:Error in /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
(Status 7)
Installation aborted[/COLOR]
Im not a software developer for mobile phones but I guess it is trying to tell me, that the ROM which I'm trying to install isnt working on my device.
But I am absolutely sure that I got an I9305 as you can see on the attached screenshot.
Any ideas?
I have also redownloaded the ZIP and tried it multiple times but always ended up with the same error.
I really would appreciate any help!
Click to expand...
Click to collapse
Try to install the latest CWM!
Sent from my GT-I9305 using xda premium
update your recovery. I suggest philz
Awesome! This ROM really rocks!
Is there any way to disable the 3 button-elements as my phone already has real buttons?
yes, Google it
Celaniry said:
Awesome! This ROM really rocks!
Is there any way to disable the 3 button-elements as my phone already has real buttons?
Click to expand...
Click to collapse
If you go into the settings where you set tablet, phablet or stock ui mode you can go deeper into those settings from there. Can't remember what they're called right now. In stock ui you can reduce the soft buttons percentage to 0.
Hope this will help you.
Sent from my GT-I9305 using xda premium
"semi bricked" i9305 using Odin Mobile App
Hi guys,
I decided to flash Paranoid Android 4.2.2 onto my SIII i9305 and was successful using the Odin Mobile App after several other failed options.
I was about 5 minutes into enjoying the new ROM and I thought wait a second have I installed the Google Apps to the phone (NB I had placed the gapps on the external SD card along with the ROM.
In a moment of utter stupidity I opened up the Odin Mobile App again and selected flash gapps. Then when the phone was rebooting it just stuck on the recovery screen and when I selected "apply update from external storage" and chose the ROM (pa_i9305-3.65-9JUL2013-gokussjx.zip). It then displayed
E: failed to verify whole-file signature
E: signature verification failed
I cannot get beyond the recovery screen at all and when I select reboot system now the "Samsung Galaxy S3 GT i9305" screen appears 3 times and then returns back to the recovery screen.
I have no idea what to do and have googled possible solutions and come up with one that looks like a possible fix: iandroidblog.com/how-to-unroot-galaxy-s3-lte-i9305/
Waiting for my girlfriend to bring home her PC from work so I can let you know how it goes but in the interim does anyone have any ideas?
Cheers!
Try to get into download mode and flash a stock image using odin.
After that, you can root and flash CWM/TWRP again and flash your favorite custom ROM.
Edit: Make sure to wipe/factory reset when going back to Stock from AOSP/AOKP as the layout is totally different and may cause boot loops in itself (from my own experience)
latest version
PA i9305 3.99 RC2
The latest version incl. Modem and working Kernel.
BACON - i9305 trouble
tried to install PA today,on my i9305, but got error, not suported deveice, pakage for BACON a00001, this is m0
Is it possible to have PA on my device?
No i install CW, but i really would like PA.
Thanks!
Link to Paranoid ROM
Can anybody pleaase help me?
I cant find a paranoid rom that lets me install it.WHen install i get error. So therfore please give me a link for rom, and for gaps for the rom.
Thanks so much in advance!!!
Torsoen
torsoen said:
Can anybody pleaase help me?
I cant find a paranoid rom that lets me install it.WHen install i get error. So therfore please give me a link for rom, and for gaps for the rom.
Thanks so much in advance!!!
Torsoen
Click to expand...
Click to collapse
what error?
NOW I know these "Phone unable to boot" things are common, but please listen, you will make my day if my phone gets fixed
The phone is locked on Telstra (The reason I tried to root it, to unlock it)
I recently used the Samsung Galaxy SIII Toolkit located at SkipSoft [dot] net (Can't post links, new to forums).
When I started it up it said that there was an auto update that supported 4.1.2 but only donators could access that and I couldn't find the update anywhere on the internet, so I proceeded into the version without 4.1.2, and (Silly me) decided to use the non-4G version of 4.1.2 root (Since the 4G section didn't support it yet) and this may have been what broke my phone, the root process included using Odin and other means of rooting and I wasn't able to make it to the end since when the phone rebooted to hopefully be rooted, it wouldn't boot up ( ;_; ) So I decided to retry the root process (Silly me, again) and it only made it worse and my phone was stuck on the "Downloading...Do not turn off the target !!", and I couldnt go anywhere else even if I took out the battery and put it back in, tried going into recovery. So, since it was in the Download mode I was ablt to use Odin to load things onto the phone so I loaded CWM-based recovery v5.5.0.4 : : CF-v1.5 and used ADB to push a compatible Cyanogen mod zip to the recovery, when I thought that I'd done it, nope, errors, errors everywhere. So at this point I'm completely stuck on what to do so I came here to where all you extremely smart and amazing people do magic with phones. I'm going to list the error that shows up when I try to install (It's a big error, I have to type it)
-- Installing: /sdcard/cm-10.1 - 20130501 - NIGHTLY - i9305.zip
Finding update package...
Opening update package...
Installing update... (Commence huge error)
assert failed: getprop("ro.product.device") == "
m3" || getprop("ro.build.product") == "m3" ||
getprop("ro.product.device") == "m3xx" || g
etprop("ro.build.product") == "m3xx" || g
etprop("ro.product.device") == "i9305" || getpro
p("ro.build.product") == "i9305" || getpr
op('ro.product.device") == "GT-I9305" || getprop
("ro.build.product") == "GT-I9305"
E:Error in /sdcard/cm-10.1 - 20130501 - NIGHTLY - i9305.zip
(Stautus 7)
Installation aborted.
Ok, so I know I probably did not have to list the whole error, but I do want to get it fixed, my great friend gave me this phone for FREE in great condition.
Thankyou in advance for people who help fix the problem :fingers-crossed:
Read this, then use it...
http://forum.xda-developers.com/showthread.php?t=1942150
This will then give you a working rooted phone to adapt as you please...
Raistlin1158 said:
Read this, then use it...
http://forum.xda-developers.com/showthread.php?t=1942150
This will then give you a working rooted phone to adapt as you please...
Click to expand...
Click to collapse
Thank you, let's hope this works
(Loving how fast the community can reply )