Database Develop

(Status 7) Installaiton Aborted

Installing update...
assert failed: getprop("ro.product.device") == "SCH-I800" || getprop("ro.build.product") == "SCH-I800" ||
getprop("ro.product.board") == "SCH-I800"
E:Error in/sdcard/KhasMek.DJ11.Kleanmod.v3.zip
(Status 7)
Installaiton Aborted
Can,t install rom, does anybody have some simmilar?

bombarder said:
Installing update...
assert failed: getprop("ro.product.device") == "SCH-I800" || getprop("ro.build.product") == "SCH-I800" ||
getprop("ro.product.board") == "SCH-I800"
E:Error in/sdcard/KhasMek.DJ11.Kleanmod.v3.zip
(Status 7)
Installaiton Aborted
Can,t install rom, does anybody have some simmilar?
Click to expand...
Click to collapse
Yes just search in this forum. I had the same problem too. Basically here is what to do
1- download and flash the full firmware JJ4 with pit and partition cheched (this will resolve the csc errors)
Your tab might still get stuck on the boot logo. Turn it off then go to download mode
2- Flash Gingerbread 2.3.3 following Chainfire instructions
Your tab should reboot normally.
Good luck
Sent from my GT-P1000 using XDA Premium App

I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?

bombarder said:
I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?
Click to expand...
Click to collapse
Yes gsm tab
Sent from my GT-P1000 using XDA Premium App

if I flashed it could it damage my device?I read somewhere about posibility damaging

bombarder said:
I, sorry for noob qestion, but I have cdma device I800, this method for gsm device isn,t it?
Click to expand...
Click to collapse
I actually had the same issue, and have been scouring the forums for days. Unfortunately, I wasn't able to find a solution. I tried following the instructions listed for Unbricking the Galaxy Tab and it worked for about a day.
After that it began generating errors. First my widgets disappeared saying there was a problem, second reboot wifi generated errors and wouldn't turn on, and third reboot was the Verizon Logo. When it was on the VZW logo, it would vibrate once, pause, and vibrate three times. Wash. Rinse. Repeat.
So, if this is what you were dealing with, this is what I did to resolve it. (Warning: I am not a developer, and take no responsibility for what happens should you choose to repeat my steps.)
1.) I noticed it was still on CWM3, tried to reflash Khasmek's Voodoo plus v.5. -Booted into Recovery
-Wiped Data, Cache
-Flashed
Got me out of the vzw loop. Went to boot loop.
2.) Flashed rom (tried K-lean v3 and Khasmeks Aosp and Simply Aosp.
-Copy rom to SD card.
-Boot into Recovery
-Update from Zip on SD
-Flash
Fail. Still a status 7 on install of any given rom. Still displaying CWM 3.0 after kernel flash.
3.) Heimdall with original files.
-Go look it up.
Booted, but a function died on every reboot (Camera, Wifi, Widgets, etc). Noticed that system only displayed 512 RAM. May have flashed incorrect files.
-Verified. Idiot. Downloaded and Repeated with correct files.
Still had same issue with rebooting and losing a function every time.
Still displaying CWM3.0
4.) Got frustrated. Drank a little. Remembered I had a recovery from March.
-Boot into recovery
-Backup and Restore
-Restore
Bingo. Everything seems to be functioning correctly and has been for a few days. Have rebooted multiple times, no issues. Also, CWM is 2.5 again.
Hope that helps.

[Q] Problem installing AOKP build 38

Hello all. I'm having a problem trying to install AOKP build 38 on my galaxy tab 8.9. I wiped dalvik, cache, and formatted data etc but CWM gives me this error when I try to install.:
assert failed: getprop("ro.product.device") == "p5wifi" || getprop("ro.build.product") == "p5wifi"
E:Error in /sdcard/Download/aokp_p5wifi_build-38.zip
(status 7)
Installation aborted
Click to expand...
Click to collapse
I get the same error message when trying to install build 37 as well. Anyone else run into this problem? Thanks for the help.

You need different recovery. Many people asked this before. Try to browse through the thread, and I'm sure you will find your answer ;-)
Edit: Found it for you...this is the recovery you need to use (make sure you flash recovery for the right version of tab)
3g version : http://www.mediafire.com/?7vppkt6bkga2qlj
Wifi only version : http://www.mediafire.com/?686i3h7tnczs7da
Sent from my GT-P7300 using XDA

Hey, that did the trick. Thanks. I had cwm 5504 installed, however I didnt realize there were multiple versions.
Appreciate the help.

you're wellcome ;-)

P1000 stuck at boot after updating CM9

Hi guys,
I think I (soft-)bricked my Galaxy Tab (P1000). I hope you can help me
About a month ago, my tablet had installed the Overcome Rom 4.1, based on Android 2.3.
I then decided to try CM9, so I installed one of the first CM9 official nightly builds. I think I installed it simply through the CMW Recovery.
Yesterday I found that the 9.0.0 stable build was out, so I downloaded it from get.cm.
I used Titanium Backup to backup important app data into the "internal sdcard".
Then I used ROM Manager to "install rom from sdcard", choosing to erase cache only (not data), and to create a nandroid backup of my current rom.
ROM Manager rebooted into CWM recovery and started to nandroid backup and to install the new rom.
But, sadly, at next reboot, the tablet was stuck at the samsung boot screen.
It was also impossible to enter recovery mode with the volume up key. The only working mode was the download mode (activated with volume down key)
Today I tried to flash the CWM boot image (downloaded from the Samsung Galaxy Tab (GSM): Full Update Guide" on CM website) using Odin.
Now I can access to CWM Recovery, but it shows a lot of errors.
E.g.:
entering CMW Recovery
Code:
CWM-based Recovery v.5.0.2.8
E:Can't mount /cache/recovery/log
E:Can't open /cache/recovery/log
E:Can't mount /cache/recovery/last_log
E:Can't open /cache/recovery/last_log
backup and restore > restore from internal sdcard > 2012-08-10-18-55-42
Code:
Checking MD5 sums...
Erasing boot before restore...
Restoring boot image...
Restoring system...
E:format_volume: no MTD partition "/dev/block/st19"
Error while formatting /system!
E:Can't mount /cache/recovery/log
E:Can't open /cache/recovery/log
E:Can't mount /cache/recovery/last_log
E:Can't open /cache/recovery/last_log
mounts and storage > mount /sdcard
Code:
Error mounting /sdcard!
mounts and storage > mount USB storage
Code:
E:Unable to write to ums lunfile (No such file or directory)
Now here's my questions:
1. What happened? Did I do something wrong in updating CM9 to the stable version?
2. Will I be able to restore my data and/or my nandroid backup?
I can't mount my sdcard from CMW, but when I choose "restore from internal sdcard" it correctly tells my backup date, so I think the internal sdcard content is still there somewhere...
I'd really appreciate to restore all my apps and data!
3. How can I fix this mess? I'd like to have the CM9 installed and working.
Thank you very much!! :angel:

Ok, I've just realized that the internal sdcard is /emmc and not /sdcard.
So the "mount /sdcard" error is normal.
I can correctly mount /emmc from CWM, but if I try to install a rom from a zip file (either the CM9 old nightly or the stable build, which are both saved on the internal emmc), it says:
Code:
-- Installing: /emmc/cm-9.0.0-p1.zip
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "galaxytab" || getprop("ro.build.product") == "galaxytab" ||
getprop("ro.product.device") == "GT-P1000" || getprop("ro.build.product") == "GT-P1000"
E:Error in /emmc/cm-9.0.0-p1.zip
(Status 7)
Installation aborted.
Code:
-- Installing: /emmc/cm-9-20120713-NIGHTLY-p1.zip
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "galaxytab" || getprop("ro.build.product") == "galaxytab" ||
getprop("ro.product.device") == "GT-P1000" || getprop("ro.build.product") == "GT-P1000"
E:Error in /emmc/cm-9-20120713-NIGHTLY-p1.zip
(Status 7)
Installation aborted.

Just restock and start over again:
From the thread: http://forum.xda-developers.com/showthread.php?t=1385153
How to Flash the above zips :
You need to restock your tab if you are running an old MTD build, (only if /system isn't 406 mb, check it by the command `df system` or use an app (such as root explorer) )
IF you are coming from a FSR (STL/BML) ROM (aka Samsung ROM - anything else than the latest CM9 builds / AOKP builds, i.e. any GB ROM, no need to restock)
IF you are coming from a froyo ROM, you need to flash a stock GB ROM first, follow the guide below :
Restocking :
Follow the team overcome restock guide [http://www.teamovercome.net/p1000/?page_id=17], and completely restock your tab.
Once you've flashed it, reboot into download mode again and flash any kernel with recovery (any non-MTD kernels from humberos.com.br, or this forum, for your tab model)
After you've flashed the kernel, reboot into recovery, and this time, install the zip you just downloaded from CyanogenMod servers.
Install Google Apps if you want (gapps-ics-* from goo.im) [optional]
Reboot and enjoy your tab
Normal install :
You need to have a kernel with CWM Recovery
Get the zip from the above download links
Put the zip on your sdcard, reboot into recovery, and install the zip
It'll reboot a few times during the install, that's normal

Will I lose all data on the /emmc partition (including all my TitaniumBackup files) if I restock?
If the answer is yes, is there a way to copy some files from the emmc to an external sdcard before restocking? (e.g. using CWM, or Odin/Heimdall)
Thanks.
Sent from my HTC Vision using xda app-developers app

sigitm said:
Will I lose all data on the /emmc partition (including all my TitaniumBackup files) if I restock?
Click to expand...
Click to collapse
Only if you install overcome rom (via CWM).
Sent from my GT-P1000 using Tapatalk 2

Restock to 2.3.3. Then flash overcome before flashing cm9.

sigitm said:
Ok, I've just realized that the internal sdcard is /emmc and not /sdcard.
So the "mount /sdcard" error is normal.
I can correctly mount /emmc from CWM, but if I try to install a rom from a zip file (either the CM9 old nightly or the stable build, which are both saved on the internal emmc), it says:
Code:
-- Installing: /emmc/cm-9.0.0-p1.zip
Finding update package...
Opening update package...
Installing update...
assert failed: getprop("ro.product.device") == "galaxytab" || getprop("ro.build.product") == "galaxytab" ||
getprop("ro.product.device") == "GT-P1000" || getprop("ro.build.product") == "GT-P1000"
E:Error in /emmc/cm-9.0.0-p1.zip
(Status 7)
Installation aborted.
Click to expand...
Click to collapse
I have exactly the same scenario as you described, so I'm interested, could you find a solution?
I can restock with Odin using theTeam Overcome Guide, the tab boots ok. So I try to install CM9 again, I can flash the zImage with Heimdall no problem, but when I choose install the CM9 zip from the internal sdcard, I always get the same getprop assert above. I made this loop a few times now (trying to install CM9, restock), but it's always the same.

Weird that never happen to me.
Just to be crazy, can you try flash AOKP build 40 instead?
If it works, then flash cm9.
Someone got that working before.
Sent from my GT-P1000 using xda app-developers app

priyana said:
Weird that never happen to me.
Just to be crazy, can you try flash AOKP build 40 instead?
If it works, then flash cm9.
Someone got that working before.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
restock -> overcome 4.1 -> CM9
This worked for me, thanks!

You mean restock - overcome kernel - overcome 4.1 - cm9 ?
Sent from my GT-P1000 using xda app-developers app

Qqqxxxzzz said:
sigitm said:
Will I lose all data on the /emmc partition (including all my TitaniumBackup files) if I restock?
Click to expand...
Click to collapse
Only if you install overcome rom (via CWM).
Click to expand...
Click to collapse
I restocked but sadly I lost all data on the internal sdcard. :crying:
Then I copied latest CM9 nightly rom to the internal sdcard, installed the Overcome Kernel via Odin, booted into Overcome Clockwork Mod, and successfully installed CM9.

priyana said:
You mean restock - overcome kernel - overcome 4.1 - cm9 ?
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
1. restock as described the overcome guide
2. oneclick rooting
3. overcome 4.1 with odin
4. cm9 with cwm

setalosas said:
1. restock as described the overcome guide
2. oneclick rooting
3. overcome 4.1 with odin
4. cm9 with cwm
Click to expand...
Click to collapse
Sent from my GT-P1000 using xda app-developers app
Sorry, by now I know overcome guide by heart and probably can write it out with my eyes closed.
but...
3. overcome 4.1 with odin
What is that?
I thought you flash overcome 4.0 kernel tar using Odin,
Not overcome 4.1 rom
Overcome rom is flashed using CWM only.
So, You mean restock - overcome kernel - overcome 4.1 - cm9
Rooting is redundant.

priyana said:
3. overcome 4.1 with odin
What is that?
I thought you flash overcome 4.0 kernel tar using Odin,
Not overcome 4.1 rom
Overcome rom is flashed using CWM only.
So, You mean restock - overcome kernel - overcome 4.1 - cm9
Rooting is redundant.
Click to expand...
Click to collapse
No, I didn't flash the overcome 4.0 kernel.
I used odin with the Overcome_7_Series_v4.1.0_Wipe.zip file unzipped, and put the proper files into the pit/pda/phone fields of odin. That's all.

bummer
flashed GT-P1000 with CM9.1 stable version too. Suddenly the device keeps auto shutdown with unknown problems, app crashes such as Google Play (which I itched to remove and updated to the somenumber version) and changed Apollo app back and forth and back again of 1.0 version from the separate developed apk with the original cm9 Apollo. and then after many times flashing and tried to restore the CM9.1 Stable, the device wont let me use CM9 again. On boot scanning sd card, it shuts down weirdly. maybe there's some problem for my device with CM9. sigh.

Getting ICS on the Bell Mobility GT-P1000M

Hi everyone,
I really don't like posting redundant information, but I just had to post something to help my Canadian colleagues...
I have a Samsung GT-P1000M (Bell Mobility Canada version) that I updated to Gingerbread via Kies but then wanted to get to ICS (CM9). I'll be honest I can typically easily filter through web garbage when it comes to knowing what to do but the entire world is so active on Android that I had mass confusion. There's a lot of bad information out there... In my initial attempts I had no issues rooting using SuperOneClick: http://www.androidauthority.com/galaxy-tab-p1000-root-superoneclick-72083/
Then, I installed CWM so that I could try installing the flash CM9 zip file. It would not install due to the assert statement (Status 7), where it was trying to match to a GT-P1000, but mine is an M. So I edited the script inside the zip file and tried again but it ended up going into a continuous loop on Status 7. I tried flashing again but had the same issues.
Anyway, long story short, this is what I would suggest with the M version to get CM9 (ICS). Essentially put on this overcome image so that the GT-P1000M version thinks it's a regular GT-P1000 tablet. There's no real point in rooting as you'll blow everything away anyway. Make sure to back up your stuff:
1) Do what priyana suggests in this post and restock your tablet. This involves starting on Page 6 of this guide. Finding all the files is a bit annoying, but doable. Just try to get them from reasonably trusted sources.
2) Stop following the guide at the end of page 11 to proceed to install CM9. Reboot the tablet into the CWM Recovery by holding the volume up key and power button during boot. Install the CM9 zip file as priyana suggests. Then flash the google apps obtained from goo.im (the whole thing is as easy as installing 2 zip files)
Anyway, I think it was necessary to blow away everything so that the tablet stopped believing it was actually a P1000M. Now ICS is on there and runs beautifully. I know the post is a bit redundant but it is to clear up the P1000M difference. As soon as this thing booted the web worked perfectly, never had to put any network settings in or anything.
Also this gives phone functionality, I just don't know how it will get billed considering I'm on a Tablet Only plan... I guess we'll find out in a few days when my bill comes out. It'll probably be at 25 cents/minute or something. Anyway, thanks everyone!

The overcome files are all well hosted by sos_sifou
http://forum.xda-developers.com/showthread.php?t=1881981
Anything broken, just let him know.
Sent from my GT-P1000 using xda app-developers app

Another Canadian GT-P1000M Result
Just wanted to share my experience trying to put CyanogenMod on a Bell Canada Galaxy Tab (GT-P1000M) for anyone coming across this thread. I had one of these fall into my lap, and being a nexus 5 owner, the Froyo that came stock just wasn't going to cut it.
Step1: Update the 2.3.3
First thing I did was update to 2.3.3 using Samsung Kies software on a Windows machine. Every Root+CWM path I seemed to find was aimed at 2.3 not 2.2. That was painful enough. The only real trick have to make sure to set the device up properly Settings->Wireless and Networl->USB Settings->Kies Mode (or something to that effect, I can't see this menu anymore),
Step2: Root and Custom Recovery
From there I pretty much followed the instructions at wiki.cyanogenmod.org/w/Install_CM_for_p1 for a generic P1000 (skipping the "flash gingerbread" step because I did that with Kies). The CM instructions link you to theunlockr.com/2012/05/07/how-to-root-and-flash-the-clockworkmod-recovery-on-the-galaxy-tab-p1000-running-gingerbread/ for the root and recovery installation step. This was pretty straight forward. All you need is the Odin exe, and the root and recovery tar file.
Now it's rooted and unlocked. You can reboot and make sure the superuser and CWM apps are there to be sure.
Step3: CM9.1
Continuing with the instructions at wiki.cyanogenmod.org/w/Install_CM_for_p1. I put the cm9.1.zip and the gapps zip on the table simply by plugging into my computer. Unplug and reboot into recovery with Volume Up + Power. Wipe. Try to flash the cm9.1 zip and I get this error.
assert failed: getprop("ro.product.device") == "galaxytabb" || getprop("ro.buildp.product") =="galaxytab" ||getprop("ro.product.device") == "GT-P1000" || getpropr("ro.build.product") == "GT-p1000"
E:Error in /sdcard/cm-9.0.0-RC1-p1.zip
(Status 7)
Installation aborted.
Like lucgallant mentions, it seems to be something about this tablet being a GT-P1000M as opposed to just GT-P1000.
Here was my fix:
1. Extract the cm9.1.zip
2. Navigate to \cm-9.1***\META-INF\com\google\android and open the "updater-script" in a text editor.
3. change the part with this:
assert(getprop("ro.product.device") == "galaxytab" || getprop("ro.build.product") == "galaxytab" ||
getprop("ro.product.device") == "GT-P1000" || getprop("ro.build.product") == "GT-P1000");
to this:
assert(getprop("ro.product.device") == "galaxytab" || getprop("ro.build.product") == "galaxytab" ||
getprop("ro.product.device") == "GT-P1000M" || getprop("ro.build.product") == "GT-P1000M");
4. Re-zip the folder
Here I ran into snag #1. The zip I created put an extra folder level in (e.g. cm9.1.zip / cm9.1 / META-INF instead of just cm9.1.zip / META-INF). This wouldn't let me flash the zip. Fixed this and managed to start the flash, when I ran into snag #2. Got stuck in a boot loop (one with the CM logo).
Managed to get back the the bootloader, and for the hell of it thought I'd flash the original zip that would fail on the assert message. Sure enough, that worked. So whatever I did to get stuck in the boot loop do something similar to what lucgallant said about convincing your tablet it's a GT-P1000 and not a GT-P1000M (os something). But I didn't have to do any of the overcome image stuff.
So recap:
Files needed
- Odin3 v1.7
- CF-Root-TAB7_XX_OXA_JQ1-v3.3-CWM3RFS.tar
- cm9.1.zip
- cm9.1_modified.zip (that you modified the updater_script in and make a new zip)
- gapps zip
Step1
- update to 2.3.3 in kies
Step2
- reboot into "download mode" (volume down and power)
- use the odin.exe thing to flash the CF.tar
- reboot into regular mode and make sure superuser and a cwm app are there
- put the gapps.zip, cm9.1.zip and cm9.1modified.zip
Step3
- reboot in recovery (volume up + power)
- wipe and factory reset
- flash the cm9.1.zip and fail on assert (never know, you might get lucky)
- flash the cm9.1.zip and get farther but get stuck in a bootloop
- frantic volume up and power and different times to try to get back into recovery mode
- flash the cm9.1.zip original which will now magically work
- flash the gapps.zip
- reboot
Voila. Worked for me at least.

[Q] Paranoid Android on I9305 (LTE)

Hello,
I was trying to install the Paranoid Android ROM (http://forum.xda-developers.com/showthread.php?t=2203301).
I did everything as always but unfortunately I receive an error:
Code:
CWM-based Recovery v.5.5.0.4 :: CF-v.1.5
-- Installing: /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
Finding update package...
Opening update package...
[COLOR="DarkRed"]Installing update...
assert failed: getprop("ro.product.device") == "m3" || getprop("ro.built.product") == "m3" ||
getprop("ro.product.device") == "i9305" || getprop("ro.built.product") == "i9305" ||
getprop("ro.product.device") == "GT-I9305" || getprop("ro.built.product") == "GT-I9305"
E:Error in /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
(Status 7)
Installation aborted[/COLOR]
Im not a software developer for mobile phones but I guess it is trying to tell me, that the ROM which I'm trying to install isnt working on my device.
But I am absolutely sure that I got an I9305 as you can see on the attached screenshot.
Any ideas?
I have also redownloaded the ZIP and tried it multiple times but always ended up with the same error.
I really would appreciate any help!

Celaniry said:
Hello,
I was trying to install the Paranoid Android ROM (http://forum.xda-developers.com/showthread.php?t=2203301).
I did everything as always but unfortunately I receive an error:
Code:
CWM-based Recovery v.5.5.0.4 :: CF-v.1.5
-- Installing: /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
Finding update package...
Opening update package...
[COLOR="DarkRed"]Installing update...
assert failed: getprop("ro.product.device") == "m3" || getprop("ro.built.product") == "m3" ||
getprop("ro.product.device") == "i9305" || getprop("ro.built.product") == "i9305" ||
getprop("ro.product.device") == "GT-I9305" || getprop("ro.built.product") == "GT-I9305"
E:Error in /sdcard/pa_i9053-3.15-23MAR2013-gokussjx.zip
(Status 7)
Installation aborted[/COLOR]
Im not a software developer for mobile phones but I guess it is trying to tell me, that the ROM which I'm trying to install isnt working on my device.
But I am absolutely sure that I got an I9305 as you can see on the attached screenshot.
Any ideas?
I have also redownloaded the ZIP and tried it multiple times but always ended up with the same error.
I really would appreciate any help!
Click to expand...
Click to collapse
Try to install the latest CWM!
Sent from my GT-I9305 using xda premium

update your recovery. I suggest philz

Awesome! This ROM really rocks!
Is there any way to disable the 3 button-elements as my phone already has real buttons?

yes, Google it

Celaniry said:
Awesome! This ROM really rocks!
Is there any way to disable the 3 button-elements as my phone already has real buttons?
Click to expand...
Click to collapse
If you go into the settings where you set tablet, phablet or stock ui mode you can go deeper into those settings from there. Can't remember what they're called right now. In stock ui you can reduce the soft buttons percentage to 0.
Hope this will help you.
Sent from my GT-I9305 using xda premium

"semi bricked" i9305 using Odin Mobile App
Hi guys,
I decided to flash Paranoid Android 4.2.2 onto my SIII i9305 and was successful using the Odin Mobile App after several other failed options.
I was about 5 minutes into enjoying the new ROM and I thought wait a second have I installed the Google Apps to the phone (NB I had placed the gapps on the external SD card along with the ROM.
In a moment of utter stupidity I opened up the Odin Mobile App again and selected flash gapps. Then when the phone was rebooting it just stuck on the recovery screen and when I selected "apply update from external storage" and chose the ROM (pa_i9305-3.65-9JUL2013-gokussjx.zip). It then displayed
E: failed to verify whole-file signature
E: signature verification failed
I cannot get beyond the recovery screen at all and when I select reboot system now the "Samsung Galaxy S3 GT i9305" screen appears 3 times and then returns back to the recovery screen.
I have no idea what to do and have googled possible solutions and come up with one that looks like a possible fix: iandroidblog.com/how-to-unroot-galaxy-s3-lte-i9305/
Waiting for my girlfriend to bring home her PC from work so I can let you know how it goes but in the interim does anyone have any ideas?
Cheers!

Try to get into download mode and flash a stock image using odin.
After that, you can root and flash CWM/TWRP again and flash your favorite custom ROM.
Edit: Make sure to wipe/factory reset when going back to Stock from AOSP/AOKP as the layout is totally different and may cause boot loops in itself (from my own experience)

latest version
PA i9305 3.99 RC2
The latest version incl. Modem and working Kernel.

BACON - i9305 trouble
tried to install PA today,on my i9305, but got error, not suported deveice, pakage for BACON a00001, this is m0
Is it possible to have PA on my device?
No i install CW, but i really would like PA.
Thanks!

Link to Paranoid ROM
Can anybody pleaase help me?
I cant find a paranoid rom that lets me install it.WHen install i get error. So therfore please give me a link for rom, and for gaps for the rom.
Thanks so much in advance!!!
Torsoen

torsoen said:
Can anybody pleaase help me?
I cant find a paranoid rom that lets me install it.WHen install i get error. So therfore please give me a link for rom, and for gaps for the rom.
Thanks so much in advance!!!
Torsoen
Click to expand...
Click to collapse
what error?