[Q] Galaxy Tab GT 1000N won't start - Galaxy Tab Q&A, Help & Troubleshooting

Day 1
Hard reset my device. After rebooting, my tab stuck at Samsung logo and vibrating. But still can enter download mode
Day 2
The device still stuck at Samsung logo and can enter download mode. Then i tried flashing with dbdata.rfs PDA via Odin to try my luck. After reboot , the same things goes up,stuck at Samsung logo. After few minute , i tried flashing the GT-P1000_PRT_P1000XWJQ9_P1000PRTKL1_P1000XXJPZ ROM.During flashing(i don't know either it's finish already or not or either battery problem.Before flash i noticed the battery has low power about less than 10%) ,the device suddenly shutdown by it self. After the shutdown, the device goes black and try to reboot again,nothing comes up.Then i thought the battery was fully drained out, then i decide to charge up till morning.
Day 3
Trying to power up the device but nothing happen.Holding the power button about 20 sec and nothing happen but the device feel a little bit hot at the back.But when i plugged in to USB, it can detect the device and show the MTP Installation has failed.But at My computer shows 2 removable disk which comes from the device it self.After i pressed it,it say Please insert a disk to removable disk.
Can anyone please help me?Help my Old Tab.

Sounds like you have bricked your device. And I mean a real brick, not a "soft brick" as some people like to call it.
You should never try and flash your device if you have low battery as power could fail and corrupt your bootloader.
If you cant get into recovery or download mode your screwed and need to send it away for JTAG fix or board replacement.

Zelz said:
Day 1
Hard reset my device. After rebooting, my tab stuck at Samsung logo and vibrating. But still can enter download mode
Day 2
The device still stuck at Samsung logo and can enter download mode. Then i tried flashing with dbdata.rfs PDA via Odin to try my luck. After reboot , the same things goes up,stuck at Samsung logo. After few minute , i tried flashing the GT-P1000_PRT_P1000XWJQ9_P1000PRTKL1_P1000XXJPZ ROM.During flashing(i don't know either it's finish already or not or either battery problem.Before flash i noticed the battery has low power about less than 10%) ,the device suddenly shutdown by it self. After the shutdown, the device goes black and try to reboot again,nothing comes up.Then i thought the battery was fully drained out, then i decide to charge up till morning.
Day 3
Trying to power up the device but nothing happen.Holding the power button about 20 sec and nothing happen but the device feel a little bit hot at the back.But when i plugged in to USB, it can detect the device and show the MTP Installation has failed.But at My computer shows 2 removable disk which comes from the device it self.After i pressed it,it say Please insert a disk to removable disk.
Can anyone please help me?Help my Old Tab.
Click to expand...
Click to collapse
Try this:
start odin, and press power + volume down for at least 5 seconds, plug to your computer
Odin should recognize your tab. Flash again. Btw jq8, sithout the correct kernel is not for p1000n/m/l.
What u did on day 3 was ALMOST right. But you didn't press the volume down. Hence you didn't go to download mode.
P.s. if you post this in the Q&Asection, we could hv helped you earlier.

Related

[Q] Foryo 2.2 problem

The odin doesnt work for me
It goes really fast and my phone never restarts.
My phone just stays on the downloading screen.
Am i using the right odin if not can any tell me where it is?
i got mine from here -> http://forum.xda-developers.com/showthread.php?t=797282
You have to start up Odin then plug in your phone while powered off, then using the button combos, vol up and down and power buttons held down at the same time when the battery charging icon flashes off for the second time release only the power button, within a few seconds you should see the download screen and Odin should see your phone, then hit start. The process should take about ten minutes, from the time Odin starts, your phone reboots and scans media.
Sounds like you had your phone in download mode before starting Odin. That is the correct Odin, check to see if Odin sees your phone forst by starting Odin and then while the phone is powered on plug it in. If Odin dosen't recognize your phone, you need the correct drivers found here http://forum.xda-developers.com/showthread.php?t=731989.

[Q] Phone will not power on after failed Odin restore

I decided to upgrade to Cog2.2beta5 from Cog2.1.4 today using ROM Manager. Everything seemed to go well but after install and reboot all I got was a black screen and subsequent reboots landed me at the same result.
So I thought restoring back to stock with Odin One Click from this forum, the one with all the ROM files built right in, was the best next step. I downloaded Odin and followed the instruction to the T and it got stuck at the PIT step. After a few attempts at it now my phone won't even power on. I've let it sit without a battery in for several minutes and even charged it on a wall charger for 30 minutes just to make sure it wasn't a dead battery. Still won't power on or respond at all.
I'm fairly new to all of this... Any ideas on what would cause a total melt down of the phone to the point of not even powering on? It has been flawless for me since launch.
Didi you download the drivers? also did you unplug the phone while doing the flash>/
pull battery sim and sd if you have one
Wait a minutes or so
plug in USB
hold vol up and down
put in battery
If the phone does not immediately go to download mode, you have a fancy paper weight that doesn't even weigh that much.
chibixzero said:
Didi you download the drivers? also did you unplug the phone while doing the flash>/
Click to expand...
Click to collapse
I did download the drivers and from everything I could see, my system and Odin recognized the phone without issue.
I had to unplug it during the process because the process froze in the same spot for well over an hour. I didn't see any other choice.
l7777 said:
pull battery sim and sd if you have one
Wait a minutes or so
plug in USB
hold vol up and down
put in battery
If the phone does not immediately go to download mode, you have a fancy paper weight that doesn't even weigh that much.
Click to expand...
Click to collapse
Guess it's a paper weight then because the phone won't power up at all let alone go into download mode.
Thanks for your time guys.
sounds like you might have done exactly what i did with my first captivate and yes it IS bricked! i know you will read "its impossible" to do that but i "thought" i followed the correct steps and flashed only a pit file. what it does is repartition your file system but apparently nothing is added after that...
not sure what steps you took on odin but it sounds like you got the same error i did and then the same issue so im going to assume the same thing has happened here...sorry matey
tnt533 said:
Guess it's a paper weight then because the phone won't power up at all let alone go into download mode.
Thanks for your time guys.
Click to expand...
Click to collapse
I had mine hosed for a while and this is what I did to get it back.
When it is unplugged and everything is out of the phone (sd, sim, batt) , hold the power button down for 10 sec, then release.
Put in battery, hold vol up + vol dwn, Plug into different usb port, Plug into phone.
That should get you into download mode
Mine did this too and the steps mentioned fixed it for me
Sent from my SAMSUNG-SGH-I897 using XDA App
I too accidently only wrote the pit file and it wouldn't do anything at all just blank screen . Make sure you remove everything open Odin one click, plug in your phone with the USB cable, hold down volume up and down and plug in battery it should start in download mode. It does work.
Sent from my SAMSUNG-SGH-I897 using XDA App
samsung captivate wont turn on after failed odin update
got an at&t samsung captivate. I want to try on something new with this phone so I search on some articles on how change rom..
first got the download mode showing on my phone then i connect it to pc with odin3 already started, I click on start button however my phone just suddenly shut off. tried turning it on but nothing happens. tried 3 key combos still wont turn on, tried removing sim, sd and batt connect phone without batt then pushing vol up and down then inserting batt still nothing. tried charging it, no light came up, still wont turn on..i would like to ask some help if how to turn my phone back on..
sorry for bad English
thank you
boangon said:
got an at&t samsung captivate. I want to try on something new with this phone so I search on some articles on how change rom..
first got the download mode showing on my phone then i connect it to pc with odin3 already started, I click on start button however my phone just suddenly shut off. tried turning it on but nothing happens. tried 3 key combos still wont turn on, tried removing sim, sd and batt connect phone without batt then pushing vol up and down then inserting batt still nothing. tried charging it, no light came up, still wont turn on..i would like to ask some help if how to turn my phone back on..
sorry for bad English
thank you
Click to expand...
Click to collapse
What did you try to flash with Odin? (with version, variant #, with/without bootloaders)
What was the Odin log?
nothing, no roms yet. i was in the first part of the instruction. this is what i follow
1. Download and install the correct drivers below (mac and linux don't need drivers)
2. Plug in your usb cable to your phone and computer
3. Open Odin
4. Enter Download Mode (see below)
5. Click Start
6. Be Patient, the first boot will take a while
where can i find the odin logs?

[Q] Samsung Galaxy S Boot Problem

I have a problem with my galaxy. It can't boot stuck on first white logo Galaxy S GT-I9000. I have do anything (volume + & center button, volume - & center button.... all combination!)
Is there any solution for this please?
The problem is exactly the same with this video: on youtube search for "Samsung Galaxy S Boot Problem"
Thanks a lot.
Nothing? please help!
I have the same issue. Tempted to try the home made jig but if there is a way without then ill try that first.
Ive tried:
Booting with various button combos.
button combos then installing battery.
combos with 3 flashes
.....
the list goes on.
My phone would happily go into download mode previously but not into OS. So I tried flashing 2.2 jp1 and it went how it is now. Odin said successful too
Hi Theodore+
I tried the jig and it worked a charm. Def recommend giving it a go.
Hi..
i'm having a weird problem..
well i upgraded to froyo 2 weeks ago using the registration trick and it was ok till yesterday.
my phone turned off suddently (while i had 60% left from battery), couldn't turn it on again.
cannot go to recovery mode, but can go to download mode.
the thing is i could boot my phone once i plug the usb to the computer or once i plug the charger..
so my phone cannot boot without being plugged
does anyone know anything about it?
Cheers..
Try pluggin in a external microSD.
Than boot and see if anything different.
Sorry xxgg but i didn't get what you're trying to tell me...
i have a microSD it's always there... how to pluggin in a microSD?
the thing is when i try to turn on my unplugged phone i see an empty battery..
once i plug it i turn it on normally..
thanks.

[Q] bricked tab after odin "success" message

i've tried to flash my tab using odin and overcome stock safe (first step on their guide). everything went ok in odin, got a green success message. but now, my tab won't turn on or do anything at all. the only response I get is after pressing the turn-on button and then the screen sort of lights up but nothing else.
Have you tried reentering download mode and flash again?
Maybe first time you did something wrong and now have to reflash a stock rom. See "How to unbrick" threads for details
hey
I can't get it into download mode at all. just the backlit screen thing
Ksoje said:
hey
I can't get it into download mode at all. just the backlit screen thing
Click to expand...
Click to collapse
Try getting into recovery, DO wipe/factory reset, clear cache, reboot... (search how to do it, can tell you, but better U search and find out)
can't do that either. I tried power button + vol up / down combo, but all i get is a backlit screen that turns off the second i release the power button
edit: not sure if its a regular brick, but what happens is this: I press the power button for about 3 seconds, the back light goes on but that's it. if i leave the button the light goes off
Does your PC recognize the Tab in that condition, if yes, connect thru Odin and flash again or try flashing overcome kernel atleast..
nope i've tried to connect it using USB but got no connection
Is your Tab fully charged ?? Try to charge it for a couple of hours and if it turns on, enter the download mode and try again. But please make sure to charge the tab.....just in case.
Good luck
yes, it was fully charged. anyway, i was able to open it up, unplug and replug the battery, but now it does nothing. doesn't light up, doesn't respond to charging or connecting to PC

M21 logo loop, can't access recovery

My mum tried to do the last update on her phone, during which most probably battery ran out - now phone is basically a brick.
When turned on it's stuck on logo loop, rebooting itself every 5-10 seconds or so vibrating once and repeating. When unplugged or plugged into the wall none of the button combinations work - the phone basically ignores everything.
When plugged to PC via USB I can invoke "updating process"? with Volume Up + Power / Volume Up combination, which should lead me to recovery menu - instead the phone goes into "update", loads bar up to 25%, gets stuck for about a minute or so, reboots and goes into logo loop.
Hard reset also "works" when plugged into PC - update screen shows up, gets stuck on 1%, phone gets hard rebooted, update comes up again, goes up to 25%, reboots and on to the logo loop...
Can I even somehow get into recovery mode to wipe cache to allow the phone to get update again or even wipe data to flash custom ROM? Screw data, I just want to make it work and not have a brick lying on the desk...
UnableToSee said:
My mum tried to do the last update on her phone, during which most probably battery ran out - now phone is basically a brick.
When turned on it's stuck on logo loop, rebooting itself every 5-10 seconds or so vibrating once and repeating. When unplugged or plugged into the wall none of the button combinations work - the phone basically ignores everything.
When plugged to PC via USB I can invoke "updating process"? with Volume Up + Power / Volume Up combination, which should lead me to recovery menu - instead the phone goes into "update", loads bar up to 25%, gets stuck for about a minute or so, reboots and goes into logo loop.
Hard reset also "works" when plugged into PC - update screen shows up, gets stuck on 1%, phone gets hard rebooted, update comes up again, goes up to 25%, reboots and on to the logo loop...
Can I even somehow get into recovery mode to wipe cache to allow the phone to get update again or even wipe data to flash custom ROM? Screw data, I just want to make it work and not have a brick lying on the desk...
Click to expand...
Click to collapse
Have you tried using reiboot-for-android.exe by Tenorshare Co Ltd? Might help. Or if the device is within warranty then try Service Centers for that device.
You can try flashing stock rom from odin.
Download your current stock rom from samfw.com and extract the zip file.
Install odin and samsung usb drivers (link) and reboot your pc.
Reboot into download mode from your phone and press volume up:
Keep USB connected, Hold Volume Down and Power buttons, When screen turns off, hold Volume Up and Volume Down buttons
Click to expand...
Click to collapse
Open odin and load the files:
AP = AP*.tar.md5, BL = BL*.tar.md5, CP = CP*.tar.md5, CSC = CSC*.tar.md5
Click to expand...
Click to collapse
Click flash and wait till it says pass
Press and hold volume down and power to reboot. The first boot can take a while. Hopefully this will fix it.

Categories

Resources