How to repair my phone - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Originally, I am using a 4.0.3 stock rom.
Then I flashed a 4.2 ABYSS kernel and pressed wipe data after.
After that, I flashed check rom v6. However, it cant boot and stops at the GT-N7000.
So I use odin to flash a rom with pda, phone and csc. However, it still cant boot and stops at GT-N7000.
All my steps should be usual as I usually flash the rom of my phone.
What can I do to boot my phone?

Did you boot back into recovery after flashing AbyssNote kernel ?
Which ICS kernel were you using when you performed wipe data / factory reset ?
Now...
Flash stock gingerbread rom with pc odin and then factory reset.
DO NOT select PIT file or boot-loader etc. Flash normally.

Boy124 said:
Did you boot back into recovery after flashing AbyssNote kernel ?
Which ICS kernel were you using when you performed wipe data / factory reset ?
Now...
Flash stock gingerbread rom with pc odin and then factory reset.
DO NOT select PIT file or boot-loader etc. Flash normally.
Click to expand...
Click to collapse
Sorry that I didn't mention it. I flashed a 2.3.6 stock rom but it can boot.
and now I am flashing a kernel with odin but stops at NAND WRITE START.
it's not my phone. please helpppppppppppp

richard4670 said:
Sorry that I didn't mention it. I flashed a 2.3.6 stock rom but it can boot.
and now I am flashing a kernel with odin but stops at NAND WRITE START.
it's not my phone. please helpppppppppppp
Click to expand...
Click to collapse
It is superbricked.
Take your phone to samsung service centre. Motherboard needs to be replaced.
Act dumb, do not tell them about custom roms and kernels, root etc and make sure you do not have yellow triangle and flash counter.
BTW Which kernel were you using before you flashed AbyssNote kernel?

richard4670 said:
Originally, I am using a 4.0.3 stock rom.
Then I flashed a 4.2 ABYSS kernel and pressed wipe data after.
After that, I flashed check rom v6. However, it cant boot and stops at the GT-N7000.
So I use odin to flash a rom with pda, phone and csc. However, it still cant boot and stops at GT-N7000.
All my steps should be usual as I usually flash the rom of my phone.
What can I do to boot my phone?
Click to expand...
Click to collapse
Did you reboot into recovery after flashing abyss kernel?
You need to reboot back into recovery after flashing abyss 4.2, so the abyss kernel takes effect.
Sounds like you didn't reboot into recovery, and wiped with an unsafe kernel.

richard4670 said:
Originally, I am using a 4.0.3 stock rom.
Then I flashed a 4.2 ABYSS kernel and pressed wipe data after.
After that, I flashed check rom v6. However, it cant boot and stops at the GT-N7000.
So I use odin to flash a rom with pda, phone and csc. However, it still cant boot and stops at GT-N7000.
All my steps should be usual as I usually flash the rom of my phone.
What can I do to boot my phone?
Click to expand...
Click to collapse
Oh MY GOD!!!! it's superbricked? I didn't reboot it after flashing the kernel. Before doing that, i am just using the stock kernel. ****
I live in HONG KONG and my phone bought in France. No warranty either... any other methods??

richard4670 said:
Oh MY GOD!!!! it's superbricked? I didn't reboot it after flashing the kernel. Before doing that, i am just using the stock kernel. ****
I live in HONG KONG and my phone bought in France. No warranty either... any other methods??
Click to expand...
Click to collapse
now i know how to flash a cwm kernel
recovery and download mode can still be entered
i just flashed a kj6 rom but no use either.
can you help me?
all thing seems normal except cant pass the bootloader
should I try flashing the bootloader and pit?

richard4670 said:
now i know how to flash a cwm kernel
recovery and download mode can still be entered
i just flashed a kj6 rom but no use either.
can you help me?
all thing seems normal except cant pass the bootloader
should I try flashing the bootloader and pit?
Click to expand...
Click to collapse
can anyone help?

richard4670 said:
can anyone help?
Click to expand...
Click to collapse
You are superbricked. Search the forum for partial recovery since you cannot claim warranty, unless you send it back to France.
Sent from my GT-N7000 using xda app-developers app

richard4670 said:
Oh MY GOD!!!! it's superbricked? I didn't reboot it after flashing the kernel. Before doing that, i am just using the stock kernel. ****
I live in HONG KONG and my phone bought in France. No warranty either... any other methods??
Click to expand...
Click to collapse
Are you sure it was stock kernel?
Stock kernels do not have clockwork recovery - so it is not possible to flash kernel from it.

richard4670 said:
now i know how to flash a cwm kernel
recovery and download mode can still be entered
i just flashed a kj6 rom but no use either.
can you help me?
all thing seems normal except cant pass the bootloader
should I try flashing the bootloader and pit?
Click to expand...
Click to collapse
If you can flash through odin without getting stuck at some point then may still be ok. Make sure to have kernel matching rom. Abyss go with gb rom.

Related

[Q] Bootloop problem

I am just about to throw my phone at the wall.
So I was on stock 2.3.3 and decided I wanted to update to ICS
http://forum.xda-developers.com/showthread.php?t=1488096
I didn't have clockwork mod and wasn't rooted so I eventually got this working
http://forum.xda-developers.com/showthread.php?t=788108
Then I tried to install the ICS rom but it wouldn't work. I then tried to flash http://forum.xda-developers.com/showthread.php?t=1353657 which for some reason didnt have any cell phone coverage.
I tried going back to the just rooted version of 2.3.3 but haven't been able to get the phone to go past the samsung logo / Clockwork Recovery.
Edit: Whenever I try flash the 2.3.3 rooted rom it updates me to Clockwork Mod Recovery v3.0.0.5 with HEAPS of errors.
Any ideas?
You should go back to a stock rom via Odin...you will need a rom that has 3 files (csc , modem, phone) and the Odin 512 .pit file and check the repartition box.
Hawkester said:
I am just about to throw my phone at the wall.
So I was on stock 2.3.3 and decided I wanted to update to ICS
http://forum.xda-developers.com/showthread.php?t=1488096
I didn't have clockwork mod and wasn't rooted so I eventually got this working
http://forum.xda-developers.com/showthread.php?t=788108
Then I tried to install the ICS rom but it wouldn't work. I then tried to flash http://forum.xda-developers.com/showthread.php?t=1353657 which for some reason didnt have any cell phone coverage.
I tried going back to the just rooted version of 2.3.3 but haven't been able to get the phone to go past the samsung logo / Clockwork Recovery.
Edit: Whenever I try flash the 2.3.3 rooted rom it updates me to Clockwork Mod Recovery v3.0.0.5 with HEAPS of errors.
Any ideas?
Click to expand...
Click to collapse
Hi bro
1. Did you download the right cf root? and how did you flash it?
2. what did it say when you installed ics? did you wipe data?
3. how did you flash back to stock?
imgibby123 said:
You should go back to a stock rom via Odin...you will need a rom that has 3 files (csc , modem, phone) and the Odin 512 .pit file and check the repartition box.
Click to expand...
Click to collapse
I've since downloaded the stock file from here http://forum.xda-developers.com/showthread.php?t=846913 and im up and running again. I don't think ill be flashing anytime soon :L
NamNamNom said:
Hi bro
1. Did you download the right cf root? and how did you flash it?
2. what did it say when you installed ics? did you wipe data?
3. how did you flash back to stock?
Click to expand...
Click to collapse
I flashed the cf root the same as the software my phone had under settings. I flashed it using odin.
There was an error message, I can't recall it exactly, it couldn't execute or something. Yup I wiped data.
Flash back to stock using odin
Thanks for the help guys
Did you solve it?
NamNamNom said:
Did you solve it?
Click to expand...
Click to collapse
Half solved, im back on stock gingerbread.
Hawkester said:
Half solved, im back on stock gingerbread.
Click to expand...
Click to collapse
I recomend flashing Codename android 1.5.5, steps:
Download the latest CNA for Galaxy S, and Gapps
Get into CWM
Wipe dalvik/cache/data
flash it
flash Gapps
Done!

go back in gingerbread

Hello everybody, My galaxy note running on MUIU Ice cream sandwish with a dangerous kernel and i want to go back on stock official gingerbread and I wondering if i can flash a stock rom via odin and if it's was dangerous for the phone , because i don't want to use the kernel abysal method.
Thank in advance
Goldiman
Well the odin way, is the safest way in my opinion.
Flash a safe kernell and then Flash the gb rom you wish via odin.
Search in the forums and you will find the exact safe steps
Sent from my GT-N7000 using Tapatalk 2
loumaros said:
Well the odin way, is the safest way in my opinion.
Flash a safe kernell and then Flash the gb rom you wish via odin.
Search in the forums and you will find the exact safe steps
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
thank for your anwser
I wondering why flash a safe kernel before?
I can just flash the full stock rom via odin on a dangerous kernel right?
Straigh way flash any stock GB ROM with PC Odin.
Very likely you will face force closes after flashing GB stock ROM, nothing to worry, just reboot to recovery and wipe cache and data, everything will be fine. Remember wiping should only perform on GB ROM.
So thank you very much everybody
so i flash the rom via odin , so the flash pass, aftert i get a bootloop on samsung logo so i shutdown my device, and
press home and power button and volume up and select wipe data and wipe cache
reboot the device and everythings is fine
dr.ketan said:
Straigh way flash any stock GB ROM with PC Odin.
Very likely you will face force closes after flashing GB stock ROM, nothing to worry, just reboot to recovery and wipe cache and data, everything will be fine. Remember wiping should only perform on GB ROM.
Click to expand...
Click to collapse
Dr.ketan, can we say this steps valid to any room ?
subrban said:
Dr.ketan, can we say this steps valid to any room ?
Click to expand...
Click to collapse
As long as you flash with odin, no need to flash safe kernel as odin does not uses recovery, but it is not advised to flash stock ICS as you may have to wipe immediately after flash. And wiping on stock ics can brick your Note.
jeetu1981 said:
As long as you flash with odin, no need to flash safe kernel as odin does not uses recovery, but it is not advised to flash stock ICS as you may have to wipe immediately after flash. And wiping on stock ics can brick your Note.
Click to expand...
Click to collapse
ٍSorry bro, could you explane this more ( but it is not advised to flash stock ICS as you may have to wipe immediately after flash )? and why did you mentioned ICS specially?
subrban said:
ٍSorry bro, could you explane this more ( but it is not advised to flash stock ICS as you may have to wipe immediately after flash )? and why did you mentioned ICS specially?
Click to expand...
Click to collapse
Most of the times we may have to wipe in stock recovery after flashing stock rom using odin (specially if flashing over custom roms or flashing GB over ICS), and we all know that Samsung ICS kernels are not safe to wipe, it may brick your device if you have to wipe in ICS stock recovery.
Best is to first flash GB, wipe and then flash ICS using odin.
jeetu1981 said:
Most of the times we may have to wipe in stock recovery after flashing stock rom using odin (specially if flashing over custom roms or flashing GB over ICS), and we all know that Samsung ICS kernels are not safe to wipe, it may brick your device if you have to wipe in ICS stock recovery.
Best is to first flash GB, wipe and then flash ICS using odin.
Click to expand...
Click to collapse
if there is special steps to flash rooms please tell me where i could find it
subrban said:
if there is special steps to flash rooms please tell me where i could find it
Click to expand...
Click to collapse
Here it is,by dr ketan
http://forum.xda-developers.com/showthread.php?t=1424997

[Q] My G-note got crashed, please help me...

My G-note (N7000) got crashed, please help me…………
After flash N7000XXLS2 my G-Note not booting up anymore. It’s stuck on Samsung logo after the boot animation.
Please help me to load N7000XXLS2 or go back to ICS.
Thanks in advance.
musheercmr said:
My G-note (N7000) got crashed, please help me…………
After flash N7000XXLS2 my G-Note not booting up anymore. It’s stuck on Samsung logo after the boot animation.
Please help me to load N7000XXLS2 or go back to ICS.
Thanks in advance.
Click to expand...
Click to collapse
stuck in Samsung logo just mean you need to just fullwipe factory in CMW. but be sure you are on safe kernel such as Speedmode or Hydracore before wiping.. i dont know if xxls2 kernel is brick free or not. but stucking at samsung logo has always been solved by fullwipe factory in my case
mistajoe83 said:
stuck in Samsung logo just mean you need to just fullwipe factory in CMW. but be sure you are on safe kernel such as Speedmode or Hydracore before wiping..
Click to expand...
Click to collapse
I did full wipe but still the same .
and now how can i load safe kernel? or any other advise to fix ?
thank you.
musheercmr said:
My G-note (N7000) got crashed, please help me…………
After flash N7000XXLS2 my G-Note not booting up anymore. It’s stuck on Samsung logo after the boot animation.
Please help me to load N7000XXLS2 or go back to ICS.
Thanks in advance.
Click to expand...
Click to collapse
It takes some time to boot up after you flash a rom..just wait for few minutes and see if it boots up
And how did you flash the rom..i mean what rom,kernel and did you do the wipes
rajsekhar.300 said:
It takes some time to boot up after you flash a rom..just wait for few minutes and see if it boots up
And how did you flash the rom..i mean what rom,kernel and did you do the wipes
Click to expand...
Click to collapse
that is correct. takes times. but if you waited more than 10 minutes try flashing other rom.. safest method is pc odin.
rajsekhar.300 said:
It takes some time to boot up after you flash a rom..just wait for few minutes and see if it boots up
And how did you flash the rom..i mean what rom,kernel and did you do the wipes
Click to expand...
Click to collapse
I was waiting more than a hours and i tried to Flash ICS by odin-3, that one also failed
i was in N7000DDLR9 ROM. then i flash N7000XXLS2 by mobi-odin
musheercmr said:
I did full wipe but still the same .
and now how can i load safe kernel? or any other advise to fix ?
thank you.
Click to expand...
Click to collapse
tell us how you flash it. via PC ODIN or ClockWorkMOD.?
as for the kernel if you have Extrnal sdcard then download SpeedMod 3-15 or Hydracore kernel than put that in your external Sdcard. Open CMW than flash the kernel then go to advance>reboot recovery.. wait for recovery rebooted than you are safe to flash other rom.
---------- Post added at 07:28 AM ---------- Previous post was at 07:20 AM ----------
look here.. theres a tutorial of flashing with PC ODIN + Firmware download..
the instruction is detailed and clear.. this should help you the most.
http://forum.xda-developers.com/showthread.php?t=1424997
musheercmr said:
I was waiting more than a hours and i tried to Flash ICS by odin-3, that one also failed
i was in N7000DDLR9 ROM. then i flash N7000XXLS2 by mobi-odin
Click to expand...
Click to collapse
How could you flash xxls2(jb leak) using pc odin..you need to do it using cwm
And what kernel were u on when you flashed xxls2
rajsekhar.300 said:
How could you flash xxls2(jb leak) using pc odin..you need to do it using cwm
And what kernel were u on when you flashed xxls2
Click to expand...
Click to collapse
finally i got installed ICS 4.0.4 (N7000DDLR6) by PC-Odin. thank you guys.
So from now, can you please advise, how can i flash JB (N7000XXLS2 LEAK). @ present my phone is not rooted. and running on fully stoke ROM N7000DDLR6. advise please...
musheercmr said:
finally i got installed ICS 4.0.4 (N7000DDLR6) by PC-Odin. thank you guys.
So from now, can you please advise, how can i flash JB (N7000XXLS2 LEAK). @ present my phone is not rooted. and running on fully stoke ROM N7000DDLR6. advise please...
Click to expand...
Click to collapse
First flash a safe kernel(like philz,hydracore or speedmod) and then flash the jb rom through cwm
rajsekhar.300 said:
First flash a safe kernel(like philz,hydracore or speedmod) and then flash the jb rom through cwm
Click to expand...
Click to collapse
since you flash through PC ODIN means everything is stocked. Means the brick bug is present. you now only have samsung stock recovery and not ClockWorkMod.
if you are planning to install just Samsung Stock Rom then this step is applicable here
http://techie-buzz.com/android/samsung-galaxy-note-jelly-bean-firmware-leaks.html
or
http://din.huluselangor.net/?p=21813&replytocom=5359&wpmp_switcher=mobile
if you are planning install xxls2 custom then you must first root your phone then install CMW and Flash Desired rom with safe kernel installed
look here for tutorial
http://forum.xda-developers.com/showthread.php?t=1329360
mistajoe83 said:
since you flash through PC ODIN means everything is stocked. Means the brick bug is present. you now only have samsung stock recovery and not ClockWorkMod.
if you are planning to install just Samsung Stock Rom then this step is applicable here
http://techie-buzz.com/android/samsung-galaxy-note-jelly-bean-firmware-leaks.html
or
http://din.huluselangor.net/?p=21813&replytocom=5359&wpmp_switcher=mobile
if you are planning install xxls2 custom then you must first root your phone then install CMW and Flash Desired rom with safe kernel installed
Click to expand...
Click to collapse
i tried the same as from 1st link, flashing by PC-Odin N7000XXLS2 (LEAK). but giving me FAIL! when i click start
i am using Odin 1.87, is that make any issue ?
musheercmr said:
i tried the same as from 1st link, flashing by PC-Odin N7000XXLS2 (LEAK). but giving me FAIL! when i click start
i am using Odin 1.87, is that make any issue ?
Click to expand...
Click to collapse
From where did you download the rom..it it was downloaded from sammobile or from that hotfile link,then you should flash it through pc odin
And if its a custom rom that you downloaded from the xda,then it should be flashed through cwm
the Sam mobile and the hot link are the same. youncan flash the rom using pc odin. but before that put the philz kernel xxls2 in the external sd. so that after the flash using odin, you can boot into recovery and flash that kernel and be safe and do the wipe.
nokiamodeln91 said:
the Sam mobile and the hot link are the same..
Click to expand...
Click to collapse
Yes i know..i said that just to make it clear for the op
Gents, Can you please clarify before I am going to do below. And advise if this is the proper way.
• Flash GB (2.3.6) and wipe
• Then flash ICS (4.0.4)
• Download Notecore (or Speedmod, CF root kernel) kernel and flash by PC-Odin
• Then copy N7000XXLS2 (LEAK) to SD card.
• Boot to CWM recovery, then flash from SD, restart.
Thanks.
musheercmr said:
Gents, Can you please clarify before I am going to do below. And advise if this is the proper way.
• Flash GB (2.3.6) and wipe
• Then flash ICS (4.0.4)
• Download Notecore (or Speedmod, CF root kernel) kernel and flash by PC-Odin
• Then copy N7000XXLS2 (LEAK) to SD card.
• Boot to CWM recovery, then flash from SD, restart.
Thanks.
Click to expand...
Click to collapse
All those steps are correct if you are about to flash a leaked jb rom
If its a leaked custom jb rom,then you need to flash it through cwm
[email protected]$3K#@R said:
All those steps are correct if you are about to flash a leaked jb rom
If its a leaked custom jb rom,then you need to flash it through cwm
Click to expand...
Click to collapse
still am in stuck.
now i have N7000DDLR9 (ICS 4.0.4) without root. then i tried to flash N7000XXLS2 (LEAK) by PC-Odin, i am getting failed.
can you please explain step by step, how do from N7000DDLR9 (without root)
thanks.
musheercmr said:
still am in stuck.
now i have N7000DDLR9 (ICS 4.0.4) without root. then i tried to flash N7000XXLS2 (LEAK) by PC-Odin, i am getting failed.
can you please explain step by step, how do from N7000DDLR9 (without root)
thanks.
Click to expand...
Click to collapse
What was the error you got in the pc odin
paste the odin logs that show failed

[Q] How to update to stock ROM?

I have read:
http://forum.xda-developers.com/showthread.php?t=1424997
http://androidforums.com/galaxy-s2-international-all-things-root/578800-what-emmc-brickbug.html
http://forum.xda-developers.com/showthread.php?t=1693704
http://forum.xda-developers.com/showthread.php?t=1644364
My question: I have a SGN infected with the eMMC bug, and I want to upgrade it to the latest stock ROM. I know very little about flashing, and I know there are some risks when doing some things. I would like to know if the first link is safe for me, and which ROM I should use of the ones listed there (I live in The Netherlands). Do you guys have any tips or some guides made for the noobs among us?
that 1st link is the safest and best.
download the rom of. your choice. It. doesn't need to be of. your region. although you can check the latest firmware on www.samfirmware.com....
Once downloaded, use pc odin with the downloaded rom tar.md5 file selected in the pda tab. The connect the phone to pc in download mode and press start.
If you are upgrading to ics, then do not do any wipes, first flash a safe kernel...
Sent from my GT-N7000 using xda premium
nokiamodeln91 said:
that 1st link is the safest and best.
download the rom of. your choice. It. doesn't need to be of. your region. although you can check the latest firmware on www.samfirmware.com....
Once downloaded, use pc odin with the downloaded rom tar.md5 file selected in the pda tab. The connect the phone to pc in download mode and press start.
If you are upgrading to ics, then do not do any wipes, first flash a safe kernel...
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
:good:
by the way what's with nokiamodeln91 username.. hahahahaha.. you are in samsung thread.. hahahahaha.. but nice one man.. great help... keep it
nokiamodeln91 said:
that 1st link is the safest and best.
download the rom of. your choice. It. doesn't need to be of. your region. although you can check the latest firmware on LINK ....
Once downloaded, use pc odin with the downloaded rom tar.md5 file selected in the pda tab. The connect the phone to pc in download mode and press start.
If you are upgrading to ics, then do not do any wipes, first flash a safe kernel...
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
Thanks for replying. Good to know that that thread is safe, but what do you mean by flashing a safe kernel? Those terms mean nothing to me.
theres two way to flash ROM. 1 is using PC ODIN and the other one is CWM
Flashing Via PC ODIN .. you need to have two thing.. The Rom You Want to flash and the PC-ODIN software
Flashing Via CWM.. you need two things. You need to root your phone and you need to install CWM.
every rom comes with modem, kernel (the file that govern how to handle your phone cpu), csc... the kernel inside ics is known to have brickbug
theres no need to flash kernel if you are flashing Rom via PC ODIN... Flashing kernel is when you are using CWM....
mistajoe83 said:
:good:
by the way what's with nokiamodeln91 username.. hahahahaha.. you are in samsung thread.. hahahahaha.. but nice one man.. great help... keep it
Click to expand...
Click to collapse
tried a few usernames dint work. tried the Samsung too, na.. then nokia to the rescue.
Sent from my GT-N7000 using xda premium
mistajoe83 said:
theres two way to flash ROM. 1 is using PC ODIN and the other one is CWM
Flashing Via PC ODIN .. you need to have two thing.. The Rom You Want to flash and the PC-ODIN software
Flashing Via CWM.. you need two things. You need to root your phone and you need to install CWM.
every rom comes with modem, kernel (the file that govern how to handle your phone cpu), csc... the kernel inside ics is known to have brickbug
theres no need to flash kernel if you are flashing Rom via PC ODIN... Flashing kernel is when you are using CWM....
Click to expand...
Click to collapse
So, I can just flash any ROM using ODIN, and there will be no risk bricking my device?
If I flash a ROM, will I have a fresh install, and will my kernel also change so that I don't have the brickbug anymore?
hiddepolen said:
So, I can just flash any ROM using ODIN, and there will be no risk bricking my device?
If I flash a ROM, will I have a fresh install, and will my kernel also change so that I don't have the brickbug anymore?
Click to expand...
Click to collapse
yes you can flash any ROM using ODIN safely without bricking your device.
yes you will have a fresh install. your kernel will change too. as for the brickbug....
If you flash via PC ODIN then everything is stock to what you flashed.the kernel the firmware the csc the modem..all as stock provided....
1.If you flash ICS via PC-ODIN then your kernel also would be stock ics kernel that has brickbug..
Warning :
Don't wipe anything from stock ICS recovery
Don't factory reset/Hard reset on stock ICS.
Don't flash any Wipe version of ICS ROM
let say you want to flash Latest JB Rom but you are on ICS stock.
first thing you need to do is root your device ...install CWM.. Flash safe kernel
http://forum.xda-developers.com/showthread.php?t=1329360
let say ive rooted... installed CWM with safe kernel...
what i always do is everytime i want to flash new rom whatever rom it is...i flash Speedmod 3-15 (safe kernel) and go to Advance>reboot recovery and flash any rom i want so that im on the safe side without worrying what kernel im on.
2.If you flash GB than your kernel will be GB kernel which is safe to wipe..
if you want to flash custom rom from gb then you root your device and installed CWM and Flash since GB kernel is safe.
but.. let say u flashed ICS and wanted to go back to GB. then you are not safe anymore,,, that is why i always flashed Speedmod kernel 3-15 (safe kernel) and reboot recovery (by going to advance>rebootrecovery) and flashed any rom... that way im always sure that im in safe kernel when flashing Rom
mistajoe83 said:
yes you will have a fresh install. your kernel will change too. as for the brickbug....
If you flash via PC ODIN then everything is stock..If you flash ICS via PC-ODIN then your kernel also would be stock ics kernel that has brickbug.. if you flash GB than your kernel will be GB kernel which is safe to wipe..
Click to expand...
Click to collapse
Thanks so much, you are an incredible help. Slowly, I begin to understand everything !
hiddepolen said:
I have read:
http://forum.xda-developers.com/showthread.php?t=1424997
http://androidforums.com/galaxy-s2-international-all-things-root/578800-what-emmc-brickbug.html
http://forum.xda-developers.com/showthread.php?t=1693704
http://forum.xda-developers.com/showthread.php?t=1644364
My question: I have a SGN infected with the eMMC bug, and I want to upgrade it to the latest stock ROM. I know very little about flashing, and I know there are some risks when doing some things. I would like to know if the first link is safe for me, and which ROM I should use of the ones listed there (I live in The Netherlands). Do you guys have any tips or some guides made for the noobs among us?
Click to expand...
Click to collapse
You can download any stock rom you want from searching it on the forum then you can flash it through ODIN using your computer

Someone Help Me Fix My Soft Bricked GT-N7000

Hi XDA members,
so heres the deal.
I have a GT-N7000, I got it from a friend, but it was soft bricked. with the kies emergency error.
i tried to do the emergency recovery with kies, but it said "GT-N7000 does not support initializing".
SO my next thought was Odin. ive downloaded about 3 or 4 firmware files. flashed them and i get stuck at the "SAMSUNG GALAXY NOTE GT-N7000" screen everytime.
i dont know what firmware it was on, and since it wont boot the only information i can provide is whats on the sticker under the battery.
idk if it was rooted, or on jb/ics/gb or custom rom. idk about the kernel. please someone help me fix this ill provide any information i can. :good: :highfive:
Is flash successful? Have you tried flashing Philz kernel through odin? Then try getting into recovery.
nokiamodeln91 said:
Is flash successful? Have you tried flashing Philz kernel through odin? Then try getting into recovery.
Click to expand...
Click to collapse
yeah the jellybean stock flashed successfully, the ics didnt. it failed during the FSFactory.
i think this is the emmc brick but i cant find a gingerbread rom to flash from odin
Flash Philz kernel and try to get into recovery.
nokiamodeln91 said:
Flash Philz kernel and try to get into recovery.
Click to expand...
Click to collapse
i tried philz , odin just gets stuck when trying to flash it

Categories

Resources