GT-i9001 Stuck at amss.mbn - Galaxy S I9000 Q&A, Help & Troubleshooting

Hi Guys,
I have a problem, I tried to update an T-mobile GT-i9001 to 2.3.6 with a T-mobile firmware.
But it was stuck at the amss.mbn part, and now I cannot boot the phone nor flash it.
But it has no problems getting in Download Mode.
Tried to flash with/without ops file, without Ops protect on and with it.
Tried One package box, Tried PDA box.
Tried rebooting. Tried another computer.
Tried original driver setup. And i'm flashing with Odin v4.43
Nothing works .
When I boot the phone it shows a phone and pc logo.
Thank you!

jeantje said:
Hi Guys,
I have a problem, I tried to update an T-mobile GT-i9001 to 2.3.6 with a T-mobile firmware.
But it was stuck at the amss.mbn part, and now I cannot boot the phone nor flash it.
But it has no problems getting in Download Mode.
Tried to flash with/without ops file, without Ops protect on and with it.
Tried One package box, Tried PDA box.
Tried rebooting. Tried another computer.
Tried original driver setup. And i'm flashing with Odin v4.43
Nothing works .
When I boot the phone it shows a phone and pc logo.
Thank you!
Click to expand...
Click to collapse
Apparently, your phone does not have a workable rom on it so you need to search for the correct firmware for your unit before you try again
the procedure should be
First remove battery and reinsert
1) "Select OPS" AriesVE.ops
2) Unzip/unrar the ROM you are flashing.
If it's a single .tar.md5 file, check the option "One Package" in Odin and then load the .tar.md5 file using the One Package button at the very bottom. Odin will load it and check the MD5 checksum. and should be over in ten minutes
If your ROM consists of several .smd files,
Select Boot_loader.tar under BOOT
Select Modem under PHONE
Select PDA under PDA
Select CSC under CSC .
Press Start, Flashing should take about 10 minutes
If it fails, than try again with protect ops unchecked

I tried with 3 roms with the steps u said but it still doesnt work

jeantje said:
I tried with 3 roms with the steps u said but it still doesnt work
Click to expand...
Click to collapse
what roms are trying with?
remove SD card, and Sim Card, and reinsert battery after battery pull, to try again, there is no reason for it to fail, unless you have the wrong firmware
ok, found this firmware list of Roms for I9001 on XDA..verify you got the correct one http://forum.xda-developers.com/showthread.php?t=1346245&page=3

xsenman said:
what roms are trying with?
remove SD card, and Sim Card, and reinsert battery after battery pull, to try again, there is no reason for it to fail, unless you have the wrong firmware
ok, found this firmware list of Roms for I9001 on XDA..verify you got the correct one http://forum.xda-developers.com/showthread.php?t=1346245&page=3
Click to expand...
Click to collapse
Gonna try again with GT-I9001_XEO_I9001XXKPU_I9001XXKPH_I9001OXAKP1.rar

jeantje said:
Gonna try again with GT-I9001_XEO_I9001XXKPU_I9001XXKPH_I9001OXAKP1.rar
Click to expand...
Click to collapse
Nope still stuck at amss.mbn

jeantje said:
Nope still stuck at amss.mbn
Click to expand...
Click to collapse
Ok, is your unit sim locked to any Network?
IF not can you go into recovery mode? wipe everything / factory reset and remove sd card as well as sim card before you try again
preferably use an earlier version of the rom http://forum.xda-developers.com/showthread.php?t=1346245 according to this post, its 1. I9001XEKE8 [05.2011]
and also make a post in I9001 Q&A thread, to see IF anyone else knows something about your problem

xsenman said:
Ok, is your unit sim locked to any Network?
IF not can you go into recovery mode? wipe everything / factory reset and remove sd card as well as sim card before you try again
preferably use an earlier version of the rom http://forum.xda-developers.com/showthread.php?t=1346245 according to this post, its 1. I9001XEKE8 [05.2011]
and also make a post in I9001 Q&A thread, to see IF anyone else knows something about your problem
Click to expand...
Click to collapse
Ok i finally got it to work, it looks like the ops file was corrupt that came from samfirmware.com

jeantje said:
Ok i finally got it to work, it looks like the ops file was corrupt that came from samfirmware.com
Click to expand...
Click to collapse
good job, at least you can have some peace of mind now:highfive:

Still stuck there..
xsenman said:
good job, at least you can have some peace of mind now:highfive:
Click to expand...
Click to collapse
Hi Guys, I tried all the possible steps I could find on the Internet however I'm still stuck at <1> amss.mbn download.. stage. Can't get any further, any help?
Jim.

Related

[Q] Samsung Galaxy s stuck in loop with Ultimate rom ?

Hi Guys,
apologies in advance but I have Galaxy S and since this morning it s just in boot up mode was flashed and rooted with ( Ultimate Rom ) so all i get when i press power button is ultimate home page and then second ultimate loading up page and thats it does not open up properly and it vibrates too ??
I have tried the volume up button power button and home button but nothing just comes up galaxy s black page then ultimate then back to Back Galaxy page < Please help as im so crap at this and got help from someone on here a while plase advise and help in english lol ???
Thanks
charlie2
Well first you are going to have to achieve either recovery or download mode.
Recovery: hold volume up + home and the hold power until the first screen pops up. Keep holding for about half a second. Which longer than instant lol
Download: same as above but volume down.
If you get to recovery try a wiping cache and dalvik. Then try boot up. If that doesn't work then you'll have to wipe/factory reset from recovery.
If that doesn't work then either download a stock firmware by Ramad on the general forum or go sammobile.com or type in darky in Google and go to his website and navigate to full releases. From there click on the latest for your phone sgs i9000. Scroll down to instructions and look for the link for 10.2 re or something similar. Its the Odin flashable rom. Alternatively just look for a from you like and flash it. If you have recovery you may be able to use CWM flash able zips otherwise you will need Odin flash able files from the places above.
Darky rom will retain root and is a custom from so it'll be easier to move to another custom from if you flash that.
That cover everything
Sent from my GT-I9000 using XDA
Talon26 said:
Well first you are going to have to achieve either recovery or download mode.
Recovery: hold volume up + home and the hold power until the first screen pops up. Keep holding for about half a second. Which longer than instant lol
Download: same as above but volume down.
If you get to recovery try a wiping cache and dalvik. Then try boot up. If that doesn't work then you'll have to wipe/factory reset from recovery.
If that doesn't work then either download a stock firmware by Ramad on the general forum or go sammobile.com or type in darky in Google and go to his website and navigate to full releases. From there click on the latest for your phone sgs i9000. Scroll down to instructions and look for the link for 10.2 re or something similar. Its the Odin flashable rom. Alternatively just look for a from you like and flash it. If you have recovery you may be able to use CWM flash able zips otherwise you will need Odin flash able files from the places above.
Darky rom will retain root and is a custom from so it'll be easier to move to another custom from if you flash that.
That cover everything
Sent from my GT-I9000 using XDA
Click to expand...
Click to collapse
Hi Talon26,
I have tried the 3 button recovery and download and nothing nada ??
I dont know which stock firmware to go for a while ago i had same problem as im having now and could not get a decent download for stock firmware any pointers in the right direction ??
can you get a Jig from a friend?
it can get you into download mod without button combination..
here is some video that might help to understand how to make one, it has instructions on the info.
also, in xda http://forum.xda-developers.com/showthread.php?t=819551
charlie2 said:
Hi Talon26,
I have tried the 3 button recovery and download and nothing nada ??
Click to expand...
Click to collapse
Yes you can use a jig that would be easiest and best for the future in-case you run into this again...
However i don't understand why download or recovery is not working if you are already on custom, you have achieved it before right? If not use a video to help.
However if the standard methods do not work then there are sill some tricks..
1. Take out the battery>>>Hold the button combo>>>Insert battery whilst holding combo>>>When the boot screen appears (Samsung GT-I9000) hold for about half a second/whole second then release>>>Wait. If it continues to boot loop again then take out battery
2. From task manager close all Kies apps/processes>>>Put your usb cable in>>>plug in your phone>>>hold the combo>>>Wait.
3.Take out battery>>>Do all of 2>>>When the USB is connected to phone whilst holding the combo insert battery>>>Wait.
4. Repeat 3 with charger instead of the USB cable
If none of that works then yes i think you will need to make or buy the jig. (Or borrow if you can). But also do a search as im not sure if i covered all the tricks. There used to be a thread on it in the general section, try search for it.
charlie2 said:
I dont know which stock firmware to go for a while ago i had same problem as im having now and could not get a decent download for stock firmware any pointers in the right direction ??
Click to expand...
Click to collapse
Sammoblie.com, [Ramad] Stock Firmware or Darky 10.2RE
Sammobile.com is straight forward. Click on smartphone, then android etc. Just follow the clicks then you select the FW that is relevant to you based on country and provider... If use the Ramad link then you will need your csc code which will be retrievable from the sammobile site its at the bottom.
Good luck
guy7685 said:
can you get a Jig from a friend?
it can get you into download mod without button combination..
here is some video that might help to understand how to make one, it has instructions on the info.
also, in xda http://forum.xda-developers.com/showthread.php?t=819551
Click to expand...
Click to collapse
Hi,
I bought jig from fleabay have inserted and i get yellow triangle in downloading mode (do not turn off target) any advice on what to do next ?
It says JIG Detected but nothing else ?
Is my phone dead for good ?
Also the link you gave is dead no go ?
Please help im stuck need step by step advice still a real novice ???
charlie2 said:
Hi,
I bought jig from fleabay have inserted and i get yellow triangle in downloading mode (do not turn off target) any advice on what to do next ?
Click to expand...
Click to collapse
Excelent this is exactly what you need to happen
charlie2 said:
Please help im stuck need step by step advice still a real novice ???
Click to expand...
Click to collapse
1. Ultimate ROM is it ICS? if yes install samsung drivers.exe from the following link http://forum.xda-developers.com/showthread.php?t=961956
2. Download stock ROM for your phone from samfirmware.com or alternatively you can use Darky's ROM
3. you will need Odin to flash the ROM it is included with Darky's ROM as is a read me file with instructions.
4. Start Odin make sure no kies processes are running if installed. If they are running Kill the processes
5. Boot phone to download mode using jig. Remove jig from phone. Plug USB cable into phone. wait for odin to detect phone then flash.
NOTE you may have to Flash once with re-partition ticked and then once without to get the rom completely booted.
Once running it is suggested to perform factory reset
Lexrsk said:
Excelent this is exactly what you need to happen
1. Ultimate ROM is it ICS? if yes install samsung drivers.exe from the following link http://forum.xda-developers.com/showthread.php?t=961956
2. Download stock ROM for your phone from samfirmware.com or alternatively you can use Darky's ROM
3. you will need Odin to flash the ROM it is included with Darky's ROM as is a read me file with instructions.
4. Start Odin make sure no kies processes are running if installed. If they are running Kill the processes
5. Boot phone to download mode using jig. Remove jig from phone. Plug USB cable into phone. wait for odin to detect phone then flash.
NOTE you may have to Flash once with re-partition ticked and then once without to get the rom completely booted.
Once running it is suggested to perform factory reset
Click to expand...
Click to collapse
Hi Mate,
Thankyou for quick reply much appreciated, I am downloading what you put in 1. now for 2. how do i know what is my stock rom ??
Thanks
charlie2
charlie2 said:
Hi Mate,
Thankyou for quick reply much appreciated, I am downloading what you put in 1. now for 2. how do i know what is my stock rom ??
Thanks
charlie2
Click to expand...
Click to collapse
Stock ROM would be what the phone was shipped with. ie carrier branded OS etc.
Darky's should work or from Samfirmware.com once registered select firmwares. Type "smartphone" OS "android" model "your model" region "your region"
you should then be left with a selection of firmwares for your handset/region
download the suitable version
Lexrsk said:
Stock ROM would be what the phone was shipped with. ie carrier branded OS etc.
Darky's should work or from Samfirmware.com once registered select firmwares. Type "smartphone" OS "android" model "your model" region "your region"
you should then be left with a selection of firmwares for your handset/region
download the suitable version
Click to expand...
Click to collapse
Hi Mate,
I`ve used jig to get into download mode then connected to lappy with odin and it found it it shows as com5......
Now ive also found on samfirmware the original stock rom and have downloaded and its on my laptop as winrar file its this one ( I9000BUJVG_I9000GVODJV5_VOD ) Vodafone uk 2011 i go to extract and i get another win rar file this one called ( JVG_JV5_JV4 ) what next ??
Thanks
charlie2
charlie2 said:
Hi Mate,
I`ve used jig to get into download mode then connected to lappy with odin and it found it it shows as com5......
Now ive also found on samfirmware the original stock rom and have downloaded and its on my laptop as winrar file its this one ( I9000BUJVG_I9000GVODJV5_VOD ) Vodafone uk 2011 i go to extract and i get another win rar file this one called ( JVG_JV5_JV4 ) what next ??
Thanks
charlie2
Click to expand...
Click to collapse
From what you describe I will assume that your computer is running windows 7. This being the case the file downloaded needs to be extracted so that you are left with 1 file called JVG_JV5_JV4
You say that you are now left with file called JVG_JV5_JV4. Have you downloaded a PIT file? If not find 512 PIT at the bottom of this post.
Once PIT file is downloaded extract file.
Select PIT and add pit file
Select PDA and then select the file extracted JVG_JV5_JV4
Then flash.
As stated before you may have to flash with repartition selected once and then once with out.
This should get you going again.
Lexrsk said:
From what you describe I will assume that your computer is running windows 7. This being the case the file downloaded needs to be extracted so that you are left with 1 file called JVG_JV5_JV4
You say that you are now left with file called JVG_JV5_JV4. Have you downloaded a PIT file? If not find 512 PIT at the bottom of this post.
Once PIT file is downloaded extract file.
Select PIT and add pit file
Select PDA and then select the file extracted JVG_JV5_JV4
Then flash.
As stated before you may have to flash with repartition selected once and then once with out.
This should get you going again.
Click to expand...
Click to collapse
Hi Mate,
Thanks for reply, I have done what you said and its doing nothing , so i tried seeing what was in JVG_JV5_JV4 file this is whats in there -
boot.bin
cache.rfs
factoryfs.rfs
modem.bin
param.lfs
Sbl.bin
zImage
dont know what to do next lol
I am sorry
cheers
charlie2
charlie2 said:
Hi Mate,
Thanks for reply, I have done what you said and its doing nothing , so i tried seeing what was in JVG_JV5_JV4 file this is whats in there -
boot.bin
cache.rfs
factoryfs.rfs
modem.bin
param.lfs
Sbl.bin
zImage
dont know what to do next lol
I am sorry
cheers
charlie2
Click to expand...
Click to collapse
when you are saying that it is doing nothing is odin flash failing ??
Flash completing and then phone not booting??
If the stock ROM is not working try Darky's 10.2 as it will generally work when other methods fail.
Mate , I can not thank you enough i tried again after i last put message on here and all done i now have 2.3.6 and as far as i am concerned all ok now. I did have to get into recovery mode after i used Odin for mob to start up and just did a system rebbot or should i say factory rebbot. All ok now and alot of songs i had were all still on memory card ok had to re install apps i had before but hey ho.
any advice on battery usage ?
a big big thankyou
Thanks
charlie2
charlie2 said:
any advice on battery usage ?
a big big thankyou
Thanks
charlie2
Click to expand...
Click to collapse
I personally use juice defender. works for me.
If i help just hit the thanks button...
Lexrsk said:
I personally use juice defender. works for me.
If i help just hit the thanks button...
Click to expand...
Click to collapse
Have posted Thanks a couple of times very grateful mate if it wasnt for the pit file you posted i would of got no where thought that file would of been with download thats why it didnt work first time.
Mille Grazie
charlie2
charlie2 said:
Have posted Thanks a couple of times very grateful mate if it wasnt for the pit file you posted i would of got no where thought that file would of been with download thats why it didnt work first time.
Mille Grazie
charlie2
Click to expand...
Click to collapse
No problem mate.
Just trying to help where i can

[Q] Phone stuck on the Samsung logo and won't go into recovery

Hey everyone
I've got a Galaxy S3 Mini GT-I8190N and I've got a huge problem.
It first started out with me trying to root my phone, everything seemed to go well until i tried to turn my phone on, which resulted in it being stuck on the samsung logo, I snooped around the internet trying to find a solution and was recommended to reflash with different tar files but nothing worked. I tried to reset to factory settings through recovery mode but I couldn't even access the recovery mode. I then tried to get back to factory settings using Samsung Kies but after the whole installation it didn't seem to work either. I tried almost everything possible, I checked out every link on the first page of google relating to my problem yet nothing works. The only thing I can do is enter download mode and that's it.
I wasn't aware of how rooting actually works and simply followed a tutorial on CNet (I can't post a link yet as I haven't reached 10 posts). Not sure if this helps but so far that's all I can remember from memory, if you need more info i'll happily share that.
download a new rom and install it per Odin (when i have this problem i do flash infected rom then i come in the recovery and restore my backup)
Kenneth000 said:
download a new rom and install it per Odin (when i have this problem i do flash infected rom then i come in the recovery and restore my backup)
Click to expand...
Click to collapse
I'm rather inexperienced with this whole rooting thing, if you don't mind, could you link me to the correct rom? I don't wanna mess things up again.
Would be greatly appreciated.
Download stock firmware for your I8190N from sammobile and flash it via odin. Give it a try
Edit: see my sig. On how to flash mini S3 via odin but dont use firmware from second post since it is not for N variant
Sent from my Galaxy using xda premium
samersh72 said:
Download stock firmware for your I8190N from sammobile and flash it via odin. Give it a try
Sent from my Galaxy using xda premium
Click to expand...
Click to collapse
Alright, going to try that.
samersh72 said:
Download stock firmware for your I8190N from sammobile and flash it via odin. Give it a try
Edit: see my sig. On how to flash mini S3 via odin but dont use firmware from second post since it is not for N variant
Sent from my Galaxy using xda premium
Click to expand...
Click to collapse
Well, I tried it but nothing happened, It's still stuck on the samsung logo screen and I can't get into recovery mode.
Edit: Oh and by nothing happened I meant it flashed and everything was successful but nothing changed
SnazzyFapple said:
Well, I tried it but nothing happened, It's still stuck on the samsung logo screen and I can't get into recovery mode.
Edit: Oh and by nothing happened I meant it flashed and everything was successful but nothing changed
Click to expand...
Click to collapse
Did you flashed firmware for N variant, and no special carrier firmware downloaded? Did it gave "pass" on odin?
If yes, try to reflash it and wait a little more to reboot (maybe)
Sent from my Galaxy using xda premium
samersh72 said:
Did you flashed firmware for N variant, and no special carrier firmware downloaded? Did it gave "pass" on odin?
If yes, try to reflash it and wait a little more to reboot (maybe)
Sent from my Galaxy using xda premium
Click to expand...
Click to collapse
I went here: http://www.sammobile.com/firmwares/ typed in GT-I8190N into the search box and downloaded United Kingdom (EE).
Should I tick off Auto-Reboot when I try it this time?
SnazzyFapple said:
I went here: http://www.sammobile.com/firmwares/ typed in GT-I8190N into the search box and downloaded United Kingdom (EE).
Should I tick off Auto-Reboot when I try it this time?
Click to expand...
Click to collapse
your carrier is (EE)?? or it is unlocked sim??? if you do not have a special carrier download this http://www.hotfile.com/dl/189236485/5a4d305/I8190NXXALL6_I8190NOXXALL3_BTU.zip.html.
regarding odin leave it at default. only "auto reboot" and "F. reset time" are ticked. put extracted (.tar) in pda.
it takes time to boot after completion.
Edit: if still doesnt work, i think you need stock recovery flashed on your device
samersh72 said:
your carrier is (EE)?? or it is unlocked sim??? if you do not have a special carrier download this http://http://www.hotfile.com/dl/189236485/5a4d305/I8190NXXALL6_I8190NOXXALL3_BTU.zip.html.
regarding odin leave it at default. only "auto reboot" and "F. reset time" are ticked. put extracted (.tar) in pda.
it takes time to boot after completion.
Click to expand...
Click to collapse
It takes time? For me it reboots as soon as it says Pass on odin, could that be part of the problem?
SnazzyFapple said:
It takes time? For me it reboots as soon as it says Pass on odin, could that be part of the problem?
Click to expand...
Click to collapse
i ment to finish booting
samersh72 said:
i ment to finish booting
Click to expand...
Click to collapse
Also, just to make sure I don't mess anything up, should I take out the battery, then disconnect the usb and try recovery mode in that order if once booting is done and the device restarts the screen is still stuck on the samsung logo?
SnazzyFapple said:
Also, just to make sure I don't mess anything up, should I take out the battery, then disconnect the usb and try recovery mode in that order if once booting is done and the device restarts the screen is still stuck on the samsung logo?
Click to expand...
Click to collapse
i think this will not help.
but you didnt answer my question about your carrier. because you flashed (EE) carrier. if it is not your carrier so flash UK (BTU). it is for unlocked sim
samersh72 said:
i think this will not help.
but you didnt answer my question about your carrier. because you flashed (EE) carrier. if it is not your carrier so flash UK (BTU). it is for unlocked sim
Click to expand...
Click to collapse
Well, my sim card is T Mobile but my network was switched to EE.
I heard that having MicroSD's and SIM cards inserted while flashing could cause problems, should I keep them both in or out?
SnazzyFapple said:
Well, my sim card is T Mobile but my network was switched to EE.
I heard that having MicroSD's and SIM cards inserted while flashing could cause problems, should I keep them both in or out?
Click to expand...
Click to collapse
i usually dont take them out. but some say its better to take them out
samersh72 said:
i usually dont take them out. but some say its better to take them out
Click to expand...
Click to collapse
I just tried to flash the BTU but it's still stuck on the samsung logo screen.
SnazzyFapple said:
I just tried to flash the BTU but it's still stuck on the samsung logo screen.
Click to expand...
Click to collapse
So u need recovery! search in dev threads
samersh72 said:
So u need recovery! search in dev threads
Click to expand...
Click to collapse
I tried all kinds of recovery attempts and none of them worked.
If it is still under warranty, try to replace it
You must be flashed wrong root file from the first. Usually, flashing stock firmware could solve this problem.

[Q] Ultimate brick

I rooted my sgs 3 mini and install custom ROMs. I loaded CM 11 (4.4.2 kitkat) from Maclaw.pl. It worked, but after few weeks, my fhone just suddenly shut down. Tried to unroot it via odin + stock ROM, but nothing happens. Or something happens, there is the samsungs own bootlogo back. But the phone is stuck on that logo. Funny part is that when I put a charger on, there appears maclaws panda charging logo. I tried to load stock charging logo via odin, but nothing happens. Phone won't get to recovery mode, but the download mode works. Any ideas what to do? Except to throw it to trash can...
If the download work so
Recovery also need to work
Try again
Also did you try flash by Odin
Sent from my GT-I8190 using xda app-developers app
oldmen said:
If the download work so
Recovery also need to work
Try again
Also did you try flash by Odin
Sent from my GT-I8190 using xda app-developers app
Click to expand...
Click to collapse
Won't go to recovery, have tried few weeks now. Download work, when tried to go recovery, it just showing the samsungs bootlogo
And yes tried flash stock ROM by odin plenty times.
Problems
Guys, i think i have similar problem. I rooted my sgs 3mini and put maclaw.pl kitkat 4.4.2, now after downloading some photos my mobile turned off, i tried to turn it on but it shown only: "samsung galaxy s3 mini i8190", after that restarted and now it wont even turn on...
Is there anything to save this mobile or? Iam soo angry on my self and on mobile -.-
blodrayn said:
Guys, i think i have similar problem. I rooted my sgs 3mini and put maclaw.pl kitkat 4.4.2, now after downloading some photos my mobile turned off, i tried to turn it on but it shown only: "samsung galaxy s3 mini i8190", after that restarted and now it wont even turn on...
Is there anything to save this mobile or? Iam soo angry on my self and on mobile -.-
Click to expand...
Click to collapse
Sad to hear :/ Hope someone can help us
Try this forum maybe will help you http://forum.xda-developers.com/showthread.php?t=2159660
Sent from my GT-I8190 using Tapatalk
oldmen said:
Try this forum maybe will help you http://forum.xda-developers.com/showthread.php?t=2159660
Sent from my GT-I8190 using Tapatalk
Click to expand...
Click to collapse
Thanks, but as I said, nothing happens. I have tried many times to flash stock firmware. I have read many posts and tips but it looks like that there is nothing to do :/
Staattius said:
Thanks, but as I said, nothing happens. I have tried many times to flash stock firmware. I have read many posts and tips but it looks like that there is nothing to do :/
Click to expand...
Click to collapse
It could be something with a corrupt param or something. Have you tried the service firmware also, not just the stock firmware?
Enable 3 button combo for recovery, do a factory reset and it will boot.
http://forum.xda-developers.com/showthread.php?t=2157105
deconectat said:
Enable 3 button combo for recovery, do a factory reset and it will boot.
http://forum.xda-developers.com/showthread.php?t=2157105
Click to expand...
Click to collapse
Tried, didn't work. Thanks for trying to help
You kan fix your phone like this
1. Download the pit file. If your phone is variant with 8Gb internal memory. Warning this pit file is only for 8Gb internal memory galaxy s3 mini all variant (i8190 i8190N i8190L) for the 16Gb variant googlelit for pit file
2. Put your phone on Download mode , conect usb cable to the phone and tick "re-partition" box
3. Choose on PIT tab your pit file from your pc where you downloaded
4. Choose on PDA tab the Stock room wat you want to flash.
5. Put again the phone in "Download mode" open again ODIN chose PDA and flash Stock Recovery. Be careful that the box is not checked "re-partition". Flash Normal. Warning this way increase binary count on Download mode. After reboot
6. Put your phone on recovery mode by holding the keys "HOME+VOLUME UP+POWER BUTONS and wipe factory reset,cashe partition and reboot the phone. Voala the phone is Works.
Follow the instructions as in the picture
joker79 said:
1. Download the pit file. If your phone is variant with 8Gb internal memory. Warning this pit file is only for 8Gb internal memory galaxy s3 mini all variant (i8190 i8190N i8190L) for the 16Gb variant googlelit for pit file
2. Put your phone on Download mode , conect usb cable to the phone and tick "re-partition" box
3. Choose on PIT tab your pit file from your pc where you downloaded
4. Choose on PDA tab the Stock room wat you want to flash.
5. Put again the phone in "Download mode" open again ODIN chose PDA and flash Stock Recovery. Be careful that the box is not checked "re-partition". Flash Normal. Warning this way increase binary count on Download mode. After reboot
6. Put your phone on recovery mode by holding the keys "HOME+VOLUME UP+POWER BUTONS and wipe factory reset,cashe partition and reboot the phone. Voala the phone is Works.
Follow the instructions as in the picture
Click to expand...
Click to collapse
Your pit-file have password protection?
Filpus said:
Your pit-file have password protection?
Click to expand...
Click to collapse
No
joker79 said:
No
Click to expand...
Click to collapse
Trying to unrar goldenxx.rar
and then comes this. its finnish and it says password needed
http://gyazo.com/9531e2ba608d103d39de9f51b32e9738
Try Now
Filpus said:
Trying to unrar goldenxx.rar
and then comes this. its finnish and it says password needed
http://gyazo.com/9531e2ba608d103d39de9f51b32e9738
Click to expand...
Click to collapse
Sorry i forgot the arhive have password. Try now i put a new arhive without password.
joker79 said:
Sorry i forgot the arhive have password. Try now i put a new arhive without password.
Click to expand...
Click to collapse
does not work :/ oh sorry forgot link http://gyazo.com/17371b77ef82a2f3804342284bdd3854
Filpus said:
does not work :/ oh sorry forgot link http://gyazo.com/17371b77ef82a2f3804342284bdd3854
Click to expand...
Click to collapse
You tick the box "re-partition" on odin ?
joker79 said:
You tick the box "re-partition" on odin ?
Click to expand...
Click to collapse
yep
Joker, have you found solution of this issue?
I have the same problem, also tried lot of thighs but nothing helped. Every try of using pit end-up with message "there is no pit partition", but stock FW I can falsh with no troubles.
Still the same behaviour only logo after staring phone and cannot get into recovery menu...

[Q] Gt-I8190 partitionning lost. Please HELP

Hi guys, newbie here trying not to brick my s3 mini any more than it is.
It all started with the lack of mobile signal, so i changed the sim card-didn't work
After a hard reset it got worse, as i got a black popup on my screen :
PDA: I8190XXAMG4
Phone : XXXX
CSC : NONE
H/W : Not Active
EF Cal Date : NONE
SMD : 01N, PBA : 04N
CAMERA : N/A, FrontCam : N/A
TSP : 0X11
TSK : 0x19
Band : GPRS, CH : N/A
UART : N/A, USB : N/A
Also, the phone will not go in recovery mode anymore, only on download mode.
I tried flashing a stock firmware with Odin, but no change. The thing is, after the phone restarts, it loses any settings i made (like wireless password, google account, etc), so if i check USB in debugging mode, after restart it will be unchecked again, so for that reason i'm not sure if the reflashing worked.
In download mode it says:
custom binary download: no
current binary:Samsung official
system status: official
At the bottom of the page: HW REV: 0x5
As far as I understand after reading the forum for about 8 hours, i've lost the partitioning of the device.
If any of you has any idea what i could do, please advise.
there are a few threads on how to fix your problem
some more reading involved
efaustino84 said:
there are a few threads on how to fix your problem
some more reading involved
Click to expand...
Click to collapse
Can you please be more specific?
i"ve been looking through the topics and couldn't find anything.
Getting a bit desperate here...bought the phone a couple of weeks ago and i don't really afford another one
Can anyone please help me?:crying:
kstk said:
Can anyone please help me?:crying:
Click to expand...
Click to collapse
refer to the threads on loading stock ROM using ODIN
those will provide you with the information to repair the phone in it's current state
you will then be able to fix the partition
Ok. So I tried numerous times to upload the stock software but absolutely nothing happens, even if ODIN says that the upload was successful. As soon as the phone restarts, it loses any settings i had done, including USB debugging mode, so maybe this is why it doesn't work. I tried selecting a CSC, but after restart it's still:''none''.
The thing is that wireless is working, so i can connect to internet, but i cannot download and install anything (no space). I will try and download an emulator via PC and put it on a memory card.
Of course, it won't read my memory card :|
kstk said:
Of course, it won't read my memory card :|
Click to expand...
Click to collapse
post a screen shot of the options you have enabled when loading via odin
efaustino84 said:
post a screen shot of the options you have enabled when loading via odin
Click to expand...
Click to collapse
here it is
kstk said:
here it is
Click to expand...
Click to collapse
all settings are ok, so flash it via Odin
AND start Odin as Admin dude
I even tried with a pit file and re-partition checked. No result.
Just flashed again with Odin started as admin. No change.
kstk said:
Just flashed again with Odin started as admin. No change.
Click to expand...
Click to collapse
i had similar problems a few months ago. So what did i do:
download the " i8190_buttonenable_cwm6.0.2.7.tar " from HERE (see attached files) and flash it via Odin (as admin)
download This rom "I8190 серв. укр.rar" from the same side and follow the instructions.
you will get a branded lafleur rom (russian), set it to your language at setup.
put any rom as zip you like on your device.
reboot into recovery with vol. up + home + power
fullwipe and flash any rom (as zip) you want.
HTH
MJ
JackoMJ said:
i had similar problems a few months ago. So what did i do:
download the " i8190_buttonenable_cwm6.0.2.7.tar " from HERE (see attached files) and flash it via Odin (as admin)
download This rom "I8190 серв. укр.rar" from the same side and follow the instructions.
you will get a branded lafleur rom (russian), set it to your language at setup.
put any rom as zip you like on your device.
reboot into recovery with vol. up + home + power
fullwipe and flash any rom (as zip) you want.
HTH
MJ
Click to expand...
Click to collapse
Just tried that, it didn't work. It's like i didn't do anything at all.
I just can't write anything on this thing
Anyway, thank you very much, guys. Any more ideas are welcome :
Was i supposed to have F. reset time checked as well?
JackoMJ said:
all settings are ok, so flash it via Odin
AND start Odin as Admin dude
Click to expand...
Click to collapse
actually given the fact that he has lost the partition those setting are not enough in my opinion
i would say load up the pit file as well as enable re-partition
efaustino84 said:
actually given the fact that he has lost the partition those setting are not enough in my opinion
i would say load up the pit file as well as enable re-partition
Click to expand...
Click to collapse
I did load the pit file and enabled the re-partition. It just doesn't change anything.
This last week it was taken back to the place i bought it from (pawn shop ), and of course, they all say (the experts they took it to) that i did something to it, and it can't be fixed, and of course it's my fault.All i did was to reset it.
Anyway, I'm still hoping to get it fixed myself, with your help, guys.
Thanks.
kstk said:
I did load the pit file and enabled the re-partition. It just doesn't change anything.
This last week it was taken back to the place i bought it from (pawn shop ), and of course, they all say (the experts they took it to) that i did something to it, and it can't be fixed, and of course it's my fault.All i did was to reset it.
Anyway, I'm still hoping to get it fixed myself, with your help, guys.
Thanks.
Click to expand...
Click to collapse
Is it booting normaly or just download mode?
Sent through time and space from my s3mini/CM11
tys0n said:
Is it booting normaly or just download mode?
Sent through time and space from my s3mini/CM11
Click to expand...
Click to collapse
It is booting normally, but it takes very long to boot.
kstk said:
It is booting normally, but it takes very long to boot.
Click to expand...
Click to collapse
You still got that FactoryApp popup on screen?
Are you rooted?
Can you enter recovery? If so, what recovery do you have?

Need help urgently

My wife was gonna install the latest update (Lollipop) today and her phone was encrypted and so she decrypted it to prepare it for installation. At 85% the phone said that it failed and that she had to do a factory reset and so she did but now it seems the bootloader or something messed up. I've tried flashing it with Odin and with the PIT file but with no success. I could really use some help here buddies...
I attached some pictures of what I see when I try to flash it in Odin and what it looks like in recovery.
Any help will be greatly appreciated!
Juan123 said:
My wife was gonna install the latest update (Lollipop) today and her phone was encrypted and so she decrypted it to prepare it for installation. At 85% the phone said that it failed and that she had to do a factory reset and so she did but now it seems the bootloader or something messed up. I've tried flashing it with Odin and with the PIT file but with no success. I could really use some help here buddies...
I attached some pictures of what I see when I try to flash it in Odin and what it looks like in recovery.
Any help will be greatly appreciated!
Click to expand...
Click to collapse
You tried flashing the boot loader thru Odin am I right? Did you try flashing the whole Firmware thru Odin? Did you put the phone on Download mode? Remember to take the battery out then boot to download mode by pressing and holding volume down+home+power button for about 3 seconds then let them go, phone will boot into Download mode, the connect your phone to pc, then Open Odin, make sure the Odin :COM is on light blue meaning they are both communicating, then go to www.sammobile.com and download the latest firmware for your device model, and follow the instructions, it have to work, but your phone will be restored to factory, good luck, cheers:fingers-crossed:
yoniinfante said:
You tried flashing the boot loader thru Odin am I right? Did you try flashing the whole Firmware thru Odin? Did you put the phone on Download mode? Remember to take the battery out then boot to download mode by pressing and holding volume down+home+power button for about 3 seconds then let them go, phone will boot into Download mode, the connect your phone to pc, then Open Odin, make sure the Odin :COM is on light blue meaning they are both communicating, then go to www.sammobile.com and download the latest firmware for your device model, and follow the instructions, it have to work, but your phone will be restored to factory, good luck, cheers:fingers-crossed:
Click to expand...
Click to collapse
Hey there friend (thanks for replying),
I tried pretty much all of what you wrote and it just says failed. I have not tried to flash the bootloader thru Odin only the firmware that I got off of sammobile... I'm at a loss not sure what to do I've never seen this before.
Juan123 said:
Hey there friend (thanks for replying),
I tried pretty much all of what you wrote and it just says failed. I have not tried to flash the bootloader thru Odin only the firmware that I got off of sammobile... I'm at a loss not sure what to do I've never seen this before.
Click to expand...
Click to collapse
Are you sure you checked everything? try from a scratch, make sure you download the firmware for your device model, a lot of users get confuse with the bunch of letters after N910... also try a different Odin like 3.09, remember to check what I told you before in Odin, also if you wanna give a try, try flashing an old kitkat firmware, all we need is to boot your phone, good cheers:fingers-crossed:
If you think I helped you in anything please Press the Thanks Button, I will appreciate it too, Thanks:highfive:
yoniinfante said:
Are you sure you checked everything? try from a scratch, make sure you download the firmware for your device model, a lot of users get confuse with the bunch of letters after N910... also try a different Odin like 3.09, remember to check what I told you before in Odin, also if you wanna give a try, try flashing an old kitkat firmware, all we need is to boot your phone, good cheers:fingers-crossed:
If you think I helped you in anything please Press the Thanks Button, I will appreciate it too, Thanks:highfive:
Click to expand...
Click to collapse
Same results "flash read error" not sure what's going on. Am still reading around on the Internet. Thanks.
Juan123 said:
Same results "flash read error" not sure what's going on. Am still reading around on the Internet. Thanks.
Click to expand...
Click to collapse
Hey just to let u know I was reading too about ur problem, this is what I found, you gonna uninstall Samsung drivers from ur pc, under control panel, and reinstall them, or let windows search for the drivers it will install them too, after you do all that, try again flashing via Odin, remember to follow all the steps, good luck, cheers:fingers-crossed:
yoniinfante said:
Hey just to let u know I was reading too about ur problem, this is what I found, you gonna uninstall Samsung drivers from ur pc, under control panel, and reinstall them, or let windows search for the drivers it will install them too, after you do all that, try again flashing via Odin, remember to follow all the steps, good luck, cheers:fingers-crossed:
Click to expand...
Click to collapse
Tried it. Thanks for your helps so far. I'm beat I've been at it all day. Gonna give it a go again tomorrow. Thanks again man.
It may be stupid question but did you flash 3 files ROM or just one file (PDA if I remember well)? If it was second option, then you shouldn't use PIT.
slowik515 said:
It may be stupid question but did you flash 3 files ROM or just one file (PDA if I remember well)? If it was second option, then you shouldn't use PIT.
Click to expand...
Click to collapse
Just one file via AP in Odin.
Why don't you just download KIES and run recovery through that it is much more simple and reliable
Yousef_Muslih said:
Why don't you just download KIES and run recovery through that it is much more simple and reliable
Click to expand...
Click to collapse
Kies doesn't register it... it just says connecting. I tried to kies 3 and 2.6 just to make sure.
It sounds like the issue is with your USB cable maybe try a different USB port preferred in the back of the system not one upfront. Make sure you have mock locations and USB debugging on. The only reason keys wouldn't detect your device is if the drivers are incorrect
There's a feature "Reactivation Lock" in security settings. Make sure it is unchecked. It is a security feature to prevent anyone from changing your system Rom.
Sent from my SM-N910G

Categories

Resources