Hello,
I bought s5830i and i did'n know about this 'i' so I try to install CMW5 for S5830 without 'i' and now when i'm trying turn on phone hanging on boot screen. Before I installed cmw5 i don't turn on "debbuging usb" option. And now when I want install branding soft via Odin it don't see my phone. I of course tunr on "download mode" using 'volume down'+'volume up'+'power' combination. What can i do whit this problem? I tried changing ports and computers. I think that problems is not chacked "debugging usb" but I dont know how i can check it now?
tamburyniarz said:
Hello,
I bought s5830i and i did'n know about this 'i' so I try to install CMW5 for S5830 without 'i' and now when i'm trying turn on phone hanging on boot screen. Before I installed cmw5 i don't turn on "debbuging usb" option. And now when I want install branding soft via Odin it don't see my phone. I of course tunr on "download mode" using 'volume down'+'volume up'+'power' combination. What can i do whit this problem? I tried changing ports and computers. I think that problems is not chacked "debugging usb" but I dont know how i can check it now?
Click to expand...
Click to collapse
Hello. Sorry for my english. You can try this guide http://forum.xda-developers.com/showthread.php?t=1551156
Sure you need Samsung Usb Driver or install Kies in your pc (kies installs drivers too).
good luck.
Now, odin see my device. I unistalled all drivers and whole Kies, and installed agan. But now I've another problem. When I trying flash Oden failed:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLD3_S5830iBTULC1_S5830iXXLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm using "Odin3_v1.84", PIT file : "cooperve_0623.pit" and ROM: "S5830iXXLD3_S5830iBTULC1_S5830iXXLD2_HOME.tar.md5" from samfirmware.com
I don't know what i'm doing wrong. I wanted add picture but i can't - I don't have 10 posts...
I used this ODIN 1.87 is preconfigured for 5830i you dont have to configure, only select files. The .pit file i used is include. http://forum.xda-developers.com/attachment.php?attachmentid=1058320&d=1336911330
1st. Turn on phone in download mode.
2nd. Press volumen up in phone to continue.
3rd. Plug usb in pc
4rd Open Odin.
Sorry for my english, good luck
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLD3_S5830iBTULC1_S5830iXXLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> BcmCP.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Now it's this. Maybe other soft,but I dont know which one?
@edit
One more question: If i have one-file om i put it in PDA box?
To FirmWare Work in ODIN, is needed split file in parts, The ODIN only flashes BOOT PHONE PDA and CSC parts!
Docky73 builded one utility for CygWin and linux split the file in parts.http://forum.xda-developers.com/showthread.php?t=1611225
I'm do it! It's weird, but I only used other usb cable. When I do it all was fin. Thankfor helping. It was very helpfull.
Still not working
I have try the above method and i m still unable to flash this galaxy ace s5830i.
find attached the screenshoot that i took.
really need help to update this phone
thank in advance
Have you closed kies. . If kies running background your flashing will never get success. .May be silly but check once
Sent from galaxy ace running S3 beta 3.1 evolution
Kies is not installed I have remove it to prevent this issue
Sent from my GT-N7000 using xda app-developers app
Related
I was trying to root my galaxy note, I download the rooted stock rom (N7000DXLC2) from here http://forum.xda-developers.com/showthread.php?t=1535025
but the odin failed and showing this
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Rooted_Stock_Odex_N7000DXLC2.tar.md5 is valid.
<OSM> MODEM.tar.md5 is valid.
<OSM> CSC_N7000OLBLC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> factoryfs.img
<ID:0/013> NAND Write Start!!
<ID:0/013>
<ID:0/013> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
then my phone can't boot anymore, it jus stuck at the samsung n7000 screen,
i tried to download stock rom and flash again, but it failed like above,
and when i go try to flash the kernel, it success to go to the recovery mode,
but it showing error like
E:Error in /cache/recovery/sec_csc.zip (status 7)
And i maybe forgot to enable usb debugging before i root, is this the cause? how i enable it now?
what can i do now? I tried to change port, change pc, uninstall kies, reinstall driver, close antivirus, and all doesn't work, please help...
To be sure, take out all unnecessary USB devices and use a USB port that's directly attached to your motherboard. Without your phone attached load Odin and load all files. Put the phone in Download mode and hook it up to your pc. When Odin recognizes it then try and flash again.
Make sure there's not a trace of Kies on the pc, just have the drivers installed.
USB debugging should not have to be enabled. There's no way of enabling it without booting up the phone and setting it in the options anyway.
bioweb said:
To be sure, take out all unnecessary USB devices and use a USB port that's directly attached to your motherboard. Without your phone attached load Odin and load all files. Put the phone in Download mode and hook it up to your pc. When Odin recognizes it then try and flash again.
Make sure there's not a trace of Kies on the pc, just have the drivers installed.
USB debugging should not have to be enabled. There's no way of enabling it without booting up the phone and set it in the options anyway.
Click to expand...
Click to collapse
I tried that, and I uninstalled the kies,
but the odin still showing the same error.
PROBLEM SOLVED
for who facing the same problem, just include a pit file in PIT,u can find it here
http://forum.xda-developers.com/showpost.php?p=23234683&postcount=10
solving this for whole day,thanks god it worked......
17n337 said:
PROBLEM SOLVED
for who facing the same problem, just include a pit file in PIT,u can find it here
http://forum.xda-developers.com/showpost.php?p=23234683&postcount=10
solving this for whole day,thanks god it worked......
Click to expand...
Click to collapse
CAUTION : Just dont go on blindly flashing the PIT file. Its a repartitioning file. To be used only when your partition is corrupted.
Galaxy Note stuck
hello,
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but operation failed showing:
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> factoryfs.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response form LOKE
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried many times but showing the same error everytime.
I am not able to go into the recovery mode......although i can go into the download mode.
When i reboot it says "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." There is no samsung logo or GT-N7000 logo when you reboot your phone. You only see this warning.
I have some imp data on my internal memory(Phone storage). I have to save that data. Please please please help me out. Is there any way to recover phone storage data???
Can anyone explain my current situation...???
vinay28761 said:
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
...
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but
...
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
...
Can anyone explain my current situation...???
Click to expand...
Click to collapse
First: this thread is marked as solved since april. Chances are very low for a reaction (but at least I did)
Second: Make a new one in Q&A
Third: What do you mean with "Took the TB"? Especially when you flash a new Stock Rom after
Fourth: Did you put the tar-file under "Phone"? Should be "PDA".
Fifth: Read a lot in the stickies here - good start for handling Odin is Dr. Ketan's thread
Sixth: your current situation might result from not reading enough. I hope you didn't brick your device and can restore a running Rom with the instructions from the stickies. Good Luck
how exactly did you reach this situation?
Did you resolve this ?
vinay28761 said:
hello,
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but operation failed showing:
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> factoryfs.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response form LOKE
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried many times but showing the same error everytime.
I am not able to go into the recovery mode......although i can go into the download mode.
When i reboot it says "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." There is no samsung logo or GT-N7000 logo when you reboot your phone. You only see this warning.
I have some imp data on my internal memory(Phone storage). I have to save that data. Please please please help me out. Is there any way to recover phone storage data???
Can anyone explain my current situation...???
Click to expand...
Click to collapse
@vinay28761
I have your exact problem. Phone came to me with problem of hanging on Samsung N7000 Logo.
After flash everything, it shows error, exactly like yours.
Were you able to fix it? How ?
dannyogolo said:
@vinay28761
I have your exact problem. Phone came to me with problem of hanging on Samsung N7000 Logo.
After flash everything, it shows error, exactly like yours.
Were you able to fix it? How ?
Click to expand...
Click to collapse
Yes, i resolved it. I just followed dr. ketan's guide to flash through ODIN properly and exactly as described. I would request you to do the same.
Hope it solves your error too. If not, please post your screenshots.
could you jst give me details about dis nand write fail problem?i m having same problem in my gt n7000
Does anyone know where i can download PIT file for samsung gts6802 and a bootloader?
It woulb be very helpful. Thank You
Hi everyone, sorry if this is the wrong place for this post, mods pls move it to the right forum.
I have a non-rooted, non-operator free Samsung Galaxy Note with Gingerbread and I want to root it, set it operator free and flash ICS.
I tried to flash a ROM via Odin (N7000XXLPY_N7000OXALPY_DBT), followed the steps (open Odin, select the md5 file @ PDA, startup the phone on download mode, connect the phone to pc, now Odin recognizes it and shows the yellow case, then I press start) but at a certain point it just stops working and I dunno what to do, its frustrating...
Here's the Odin's Console log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
It just stops at this point and don't do nothing... What can I do?
kelomancer said:
Hi everyone, sorry if this is the wrong place for this post, mods pls move it to the right forum.
I have a non-rooted, non-operator free Samsung Galaxy Note with Gingerbread and I want to root it, set it operator free and flash ICS.
I tried to flash a ROM via Odin (N7000XXLPY_N7000OXALPY_DBT), followed the steps (open Odin, select the md5 file @ PDA, startup the phone on download mode, connect the phone to pc, now Odin recognizes it and shows the yellow case, then I press start) but at a certain point it just stops working and I dunno what to do, its frustrating...
Here's the Odin's Console log:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
It just stops at this point and don't do nothing... What can I do?
Click to expand...
Click to collapse
Usually ODIN takes a lil long to flash a rom.So give it a good 10mins time and see it comoletes the installation....
Or you may use the new ODIN by grgsiocl.It shows the remaining time left to finish flashing.Its there in themes and apps section.
Sent from my GT-N7000 using xda app-developers app
sometimes 30 or more minutes.
Usually it stops there either thought corrupt download of rom, redownload it try again.
Or because you have bricked it "op op" emmc "style" way.
If you did not root phone, or put different kernels on, then dont do anything and contact entropy, he is looking for a case where without this the phone was superbricked.
Sent from my GT-N7000 using Tapatalk 2
You may not have all the drivers from Samsung? Download Kies, run it. Then turn off Kies, antivirus and firewall. Commissioning Odin as administrator.
Wait for atleast 20 mins approx to get the stage completed or throw out to samsung service center to get it done.
Swyped From My Juicy Flavoured AOKP JB.
After some help please
Every single time i run Odin to root my Galaxy S3 4G i get this error
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9305_CWM_Recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> recovery.img
<ID:0/013> Complete(Write) operation failed.
<ID:0/013> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Kies is NOT running
I have killed all Kies processes
Rebooted device
Rebooted phone .
Tried a different USB port ..
Im out of ideas .....
Im in download mode and i have made sure debugging is on ...
Any assistance is very much appreciated .
Sv: [Q] Odin Fail ....
Try another computer, older Odin or Heimdal.
Swyped on my Galaxy S III LTE
I found that Odin 3.04 is the most stable version.
Uninstall Kies and install only the samsung drivers.
Use the all in one toolkit to install the drivers.
kies infected your registry, pretty though to get rid of it, try to set up a virtual os or re-install windows
it happened to me sometime back. after learning what i understand is use kies to install drivers then uninstall after that. so it's better if you just find drivers without using keis then less problem.
drivers, here: http://forum.xda-developers.com/showthread.php?t=961956
guys i was on india jellybean official and was planning to install paranoid android
so i dowladed pholz kernal and flashed it rebooted phone
then i powered it off and went into recovery and did wipe(one which has system data cache)
then i did apply update from ext sd . but i found that my ext sd card has been clean wiped and lost all my data
and i planned to do reboot but my phone was stuck on samsung galaxy note
now i used odin to install ginjer bread on my note but odin went to factoryfs and then it shows fail
then i tried to install jellybean with odin and again same thing
following is the log in odin
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> factoryfs.img
<ID:0/016> NAND Write Start!!
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/016> Removed!!
<ID:0/017> Added!!
guys plz help what shud i do
i am out of warranty
thanks
now when i restart my phone it shows
firmware upgrade encountered a issue plz select recovery mode in kies and try again
actually got tensed
then uninstalled kies and retried flashing gb with odin and was successfull
No Problem
sitanshu91 said:
actually got tensed
then uninstalled kies and retried flashing gb with odin and was successfull
Click to expand...
Click to collapse
Its Not problem of Mobile
Its a problem in USB Cable
Plz Use Different USB cable
Always remember to kill kies via task manager (on PC) before using odin. Also remember to pause exit the antivirus software just to be sure.
Sent from my GT-N7000 using xda app-developers app
i have once rooted my N7000 after using for few months, i returned to original Jellybean OS
"""N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar"""
But now my phone is not working ""No Recovery mode, only download mode""
tried to flash a ""TWRP CWM---PhilZ-cwm6-DDLSC-ODD-5.06.1.tar,,
&,,CF-Root-SGN_XX_OXA_LPY-v5.3-CWM5"" but both failed via ""Odin_v3.04""
now i am middle of nowhere, only samsung logo & an yellow triangle.
Tried to flash original Jellybean OS several times,
""" Custom binary count is (6):crying:
Odin Dispaly this message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> factoryfs.img
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Read almost everything, tried everything one thing came across (emmc bug ????), dont want to hard brick my phone, kindly suggest me something to do with my phone,,
plz help me
Kill all kies procesess using task manager if running in the back ground. Use main usb ports, original USB cable.. Try again to flash the Philz kernel using odin 1.85.. If that fails try a different pc. Install the samsung USB driver using this
Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....
erosnyx said:
Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....
Click to expand...
Click to collapse
Go to Philz kernel thread for n7000 and read the 3rd post.. Links are there.. Try the xxlta version..