guys i was on india jellybean official and was planning to install paranoid android
so i dowladed pholz kernal and flashed it rebooted phone
then i powered it off and went into recovery and did wipe(one which has system data cache)
then i did apply update from ext sd . but i found that my ext sd card has been clean wiped and lost all my data
and i planned to do reboot but my phone was stuck on samsung galaxy note
now i used odin to install ginjer bread on my note but odin went to factoryfs and then it shows fail
then i tried to install jellybean with odin and again same thing
following is the log in odin
<ID:0/016> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> SetupConnection..
<ID:0/016> Initialzation..
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> factoryfs.img
<ID:0/016> NAND Write Start!!
<ID:0/016>
<ID:0/016> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/016> Removed!!
<ID:0/017> Added!!
guys plz help what shud i do
i am out of warranty
thanks
now when i restart my phone it shows
firmware upgrade encountered a issue plz select recovery mode in kies and try again
actually got tensed
then uninstalled kies and retried flashing gb with odin and was successfull
No Problem
sitanshu91 said:
actually got tensed
then uninstalled kies and retried flashing gb with odin and was successfull
Click to expand...
Click to collapse
Its Not problem of Mobile
Its a problem in USB Cable
Plz Use Different USB cable
Always remember to kill kies via task manager (on PC) before using odin. Also remember to pause exit the antivirus software just to be sure.
Sent from my GT-N7000 using xda app-developers app
Related
I was trying to root my galaxy note, I download the rooted stock rom (N7000DXLC2) from here http://forum.xda-developers.com/showthread.php?t=1535025
but the odin failed and showing this
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Rooted_Stock_Odex_N7000DXLC2.tar.md5 is valid.
<OSM> MODEM.tar.md5 is valid.
<OSM> CSC_N7000OLBLC2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> factoryfs.img
<ID:0/013> NAND Write Start!!
<ID:0/013>
<ID:0/013> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
then my phone can't boot anymore, it jus stuck at the samsung n7000 screen,
i tried to download stock rom and flash again, but it failed like above,
and when i go try to flash the kernel, it success to go to the recovery mode,
but it showing error like
E:Error in /cache/recovery/sec_csc.zip (status 7)
And i maybe forgot to enable usb debugging before i root, is this the cause? how i enable it now?
what can i do now? I tried to change port, change pc, uninstall kies, reinstall driver, close antivirus, and all doesn't work, please help...
To be sure, take out all unnecessary USB devices and use a USB port that's directly attached to your motherboard. Without your phone attached load Odin and load all files. Put the phone in Download mode and hook it up to your pc. When Odin recognizes it then try and flash again.
Make sure there's not a trace of Kies on the pc, just have the drivers installed.
USB debugging should not have to be enabled. There's no way of enabling it without booting up the phone and setting it in the options anyway.
bioweb said:
To be sure, take out all unnecessary USB devices and use a USB port that's directly attached to your motherboard. Without your phone attached load Odin and load all files. Put the phone in Download mode and hook it up to your pc. When Odin recognizes it then try and flash again.
Make sure there's not a trace of Kies on the pc, just have the drivers installed.
USB debugging should not have to be enabled. There's no way of enabling it without booting up the phone and set it in the options anyway.
Click to expand...
Click to collapse
I tried that, and I uninstalled the kies,
but the odin still showing the same error.
PROBLEM SOLVED
for who facing the same problem, just include a pit file in PIT,u can find it here
http://forum.xda-developers.com/showpost.php?p=23234683&postcount=10
solving this for whole day,thanks god it worked......
17n337 said:
PROBLEM SOLVED
for who facing the same problem, just include a pit file in PIT,u can find it here
http://forum.xda-developers.com/showpost.php?p=23234683&postcount=10
solving this for whole day,thanks god it worked......
Click to expand...
Click to collapse
CAUTION : Just dont go on blindly flashing the PIT file. Its a repartitioning file. To be used only when your partition is corrupted.
Galaxy Note stuck
hello,
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but operation failed showing:
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> factoryfs.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response form LOKE
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried many times but showing the same error everytime.
I am not able to go into the recovery mode......although i can go into the download mode.
When i reboot it says "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." There is no samsung logo or GT-N7000 logo when you reboot your phone. You only see this warning.
I have some imp data on my internal memory(Phone storage). I have to save that data. Please please please help me out. Is there any way to recover phone storage data???
Can anyone explain my current situation...???
vinay28761 said:
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
...
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but
...
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
...
Can anyone explain my current situation...???
Click to expand...
Click to collapse
First: this thread is marked as solved since april. Chances are very low for a reaction (but at least I did)
Second: Make a new one in Q&A
Third: What do you mean with "Took the TB"? Especially when you flash a new Stock Rom after
Fourth: Did you put the tar-file under "Phone"? Should be "PDA".
Fifth: Read a lot in the stickies here - good start for handling Odin is Dr. Ketan's thread
Sixth: your current situation might result from not reading enough. I hope you didn't brick your device and can restore a running Rom with the instructions from the stickies. Good Luck
how exactly did you reach this situation?
Did you resolve this ?
vinay28761 said:
hello,
I was running stock ICS 4.0.4 on my GT-N7000. I rooted my device. Took the titanium backup.
After this, i opened odin. Under phone i provided the path to my downloaded ICS 4.0.4 file. Odin started flashing the device but operation failed showing:
<ID:0/010> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLRB_N7000ODDLR4_N7000DDLR1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/010> Odin v.3 engine (ID:10)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> factoryfs.img
<ID:0/010> NAND Write Start!!
<ID:0/010> Transmission Complete..
<ID:0/010> Now Writing.. Please wait about 2 minutes
<ID:0/010>
<ID:0/010> Receive Response form LOKE
<ID:0/010> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Tried many times but showing the same error everytime.
I am not able to go into the recovery mode......although i can go into the download mode.
When i reboot it says "Firmware upgrade encountered an issue. Please select recovery mode in kies & try again." There is no samsung logo or GT-N7000 logo when you reboot your phone. You only see this warning.
I have some imp data on my internal memory(Phone storage). I have to save that data. Please please please help me out. Is there any way to recover phone storage data???
Can anyone explain my current situation...???
Click to expand...
Click to collapse
@vinay28761
I have your exact problem. Phone came to me with problem of hanging on Samsung N7000 Logo.
After flash everything, it shows error, exactly like yours.
Were you able to fix it? How ?
dannyogolo said:
@vinay28761
I have your exact problem. Phone came to me with problem of hanging on Samsung N7000 Logo.
After flash everything, it shows error, exactly like yours.
Were you able to fix it? How ?
Click to expand...
Click to collapse
Yes, i resolved it. I just followed dr. ketan's guide to flash through ODIN properly and exactly as described. I would request you to do the same.
Hope it solves your error too. If not, please post your screenshots.
could you jst give me details about dis nand write fail problem?i m having same problem in my gt n7000
Does anyone know where i can download PIT file for samsung gts6802 and a bootloader?
It woulb be very helpful. Thank You
EDIT: Rebooted my computer and phone and it flashed fine. Thank you for all the help. I'm off to explore the world of custom roms.
Finally decided to root my phone and install CM9 from GB 2.3.6 with the LA4 Kernel. Downloaded everything I needed as per Post 3 of this thread. Accidentally flashed the newer kernel instead of the pre rooted ROM.
Realizing my mistake, I tried flashing the correct ROM and PC Odin gives me a failure. The phone won't boot, it just stays stuck on the Galaxy Note N7000 Logo with an exclamation mark at the bottom.
Check if you have cwm (power+home +volume up) If so then flash this get the standard version, then go advanced options and reboot recovery...
After that do all wipes data/cache/Dalvik cache then flash the cm9 for n7000,then flash cm9 GApps then reboot...
After the system boots to android set it up and download triangle away and use it to get rid of the yellow triangle
If you don't have cwm then download a stock GB rom and flash it via odin... Start from scratch
Cheers
Tapatalking on my GT-N7000
what is the error pc odin giving you?
Don't quite remember anymore since it was from this morning. All I recall is the little box on the top left going red.
Could I try replicating the problem or do I risk damaging my phone?
odin won't damage the phone. As above poster said check if you have cwm, else use Odin again
nokiamodeln91 said:
odin won't damage the phone. As above poster said check if you have cwm, else use Odin again
Click to expand...
Click to collapse
No, I don't have CWM so I've been downloading a stock rom since I saw that post should take an hour with glorious third world internet. In the meantime should I fish out that error message you requested or is it not worth it at this point?
If you need all data back and everything to be working I would recommend you to flash back the same ROM you had earlier using odin.
Go back to Square 1.
Then root it from Dr Ketan's post.
as you downloading the rom. you are going to use Odin again. Let know the error
Yeap, another fail while using PCOdin.
Going to install samsung USB drivers from the file in this thread and get rid of Kies.
Here's the stuff from the little window.
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/007> Added!!
Edit: Tried again after reinstalling drivers. Still no go.
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLA4_N7000OXALA4_N7000XXLA4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
great
After some help please
Every single time i run Odin to root my Galaxy S3 4G i get this error
<ID:0/013> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9305_CWM_Recovery.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/013> Odin v.3 engine (ID:13)..
<ID:0/013> File analysis..
<ID:0/013> SetupConnection..
<ID:0/013> Initialzation..
<ID:0/013> Get PIT for mapping..
<ID:0/013> Firmware update start..
<ID:0/013> recovery.img
<ID:0/013> Complete(Write) operation failed.
<ID:0/013> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Kies is NOT running
I have killed all Kies processes
Rebooted device
Rebooted phone .
Tried a different USB port ..
Im out of ideas .....
Im in download mode and i have made sure debugging is on ...
Any assistance is very much appreciated .
Sv: [Q] Odin Fail ....
Try another computer, older Odin or Heimdal.
Swyped on my Galaxy S III LTE
I found that Odin 3.04 is the most stable version.
Uninstall Kies and install only the samsung drivers.
Use the all in one toolkit to install the drivers.
kies infected your registry, pretty though to get rid of it, try to set up a virtual os or re-install windows
it happened to me sometime back. after learning what i understand is use kies to install drivers then uninstall after that. so it's better if you just find drivers without using keis then less problem.
drivers, here: http://forum.xda-developers.com/showthread.php?t=961956
Hi,
few days back i installed cyanogenmod on my phone (galaxy note 1 n7000 international version). after few days the phone restarted and got stuck on samsung note logo with yellow triangle
I tired installing stock firmware using odin , but every time i tried , odin failed to write on the device. there was no progress bar on the screen.
can anyone help me with this?
Not enough details:
What rom version did you try to install?
Did Odin "see" your device? (Uninstall Kies, install Samsung USB Device Driver separately)
Where die Odin stop? (snapshot)
ThaiDai said:
Not enough details:
What rom version did you try to install?
Did Odin "see" your device? (Uninstall Kies, install Samsung USB Device Driver separately)
Where die Odin stop? (snapshot)
Click to expand...
Click to collapse
Hi ,
i tried using N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 , odin identifies the device
following is the log of odin
ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Firmware update start..
<ID:0/005> system.img
<ID:0/005> NAND Write Start!!
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
Please make a snapshot of Odin, so we can see the details etc. And you do not need to write down everything. Thanks
i have once rooted my N7000 after using for few months, i returned to original Jellybean OS
"""N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar"""
But now my phone is not working ""No Recovery mode, only download mode""
tried to flash a ""TWRP CWM---PhilZ-cwm6-DDLSC-ODD-5.06.1.tar,,
&,,CF-Root-SGN_XX_OXA_LPY-v5.3-CWM5"" but both failed via ""Odin_v3.04""
now i am middle of nowhere, only samsung logo & an yellow triangle.
Tried to flash original Jellybean OS several times,
""" Custom binary count is (6):crying:
Odin Dispaly this message
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DDLSC_N7000ODDLSC_N7000DDLS6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> factoryfs.img
<ID:0/007> NAND Write Start!!
<ID:0/007> Complete(Write) operation failed.
<ID:0/007> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Read almost everything, tried everything one thing came across (emmc bug ????), dont want to hard brick my phone, kindly suggest me something to do with my phone,,
plz help me
Kill all kies procesess using task manager if running in the back ground. Use main usb ports, original USB cable.. Try again to flash the Philz kernel using odin 1.85.. If that fails try a different pc. Install the samsung USB driver using this
Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....
erosnyx said:
Thanks for reply Buddy, can you plzz guide me the exact or specific philZ kernel + recovery to flash via odin 1.85...:crying:
i have already tried most of it,,, which i used earlier for rooting my phone....
Click to expand...
Click to collapse
Go to Philz kernel thread for n7000 and read the 3rd post.. Links are there.. Try the xxlta version..