Related
I'll do a more detailed review tonight and switch out the photos with better ones too.
First impressions: Holy crap this is huge!
It is very reminiscent of the commuter series for the HTC Hero (of course). However, this one feels a bit more "rugged".
The case has the standard plugs for the headphones and microusb ports. It also has the raised areas for the volume rocker and on/off button. The front is well protected and thick enough to not really have to worry about placing the phone face down.
It was much easier to attach than the Sedio Innocase! And conversely, it's a PAIN to remove (which is a good thing!)
It takes about the same amount of force to slide open the keyboard. It's borderline too hard for me.
Oh, the keyboard lights aren't completely covered either! Granted you still can't see them looking directly down at the phone, you can see them if you tilt the phone back a little.
My initial qualms are:
1) The case is slightly too long for the phone. The top of the case that is around the keyboard is loose. Not just a little, but it looks like it wasn't even meant for this phone.
2) Like the mini-usb plug on the Hero's commuter series, the micro-usb plug on the Shift's commuter series doesn't want to stay in.
3) Since the back side is beveled and it's semi-hard to slide out, it sometimes takes a couple tries because it keeps slipping out of my hands.
Nit-picks:
1) Backside cover is off-center (flash/camera/speaker aren't centered in their respective cutouts)
2) No silicone on the front so when it's face down it slides around easily (compared to the hero which had silicone bumpers on the front)
Where did you get it from? Still says preorder on my end
Sent from my MiuiSpeedy with that Premium XDA App
just ordered mine, hope its protective. It feels good to raw dog, but its dangerous.
Rooster85 said:
Where did you get it from? Still says preorder on my end
Sent from my MiuiSpeedy with that Premium XDA App
Click to expand...
Click to collapse
Otterbox.com EVO Shift 4G Commuter Series
southernstyle said:
just ordered mine, hope its protective. It feels good to raw dog, but its dangerous.
Click to expand...
Click to collapse
It's does a very good job of covering up the phone and not being loose.
Got mine today, as wizputer noted the mini-usb isn't snug enough to remain in the port. Otherwise, very impressed with the design and construction of the case.
got mine in today, very pleased. although it was a little bit of a b*^&h to put on. After getting it on I noticed the usb plug being a pain, and the power button seems to need a lil extra force to actually click, but other than that love it. I feel safe now
Good review, disappointed, love my Otterbox's for my EVO and HD2. The split covers though, Shift and Tilt (from experience), just do not seem to provide the same kind of coverage but I do not know what else they could do to make them better.
nativ73 said:
Got mine today, as wizputer noted the mini-usb isn't snug enough to remain in the port. Otherwise, very impressed with the design and construction of the case.
Click to expand...
Click to collapse
I ended up cutting my usb plug off because of the headache it was causing.
Sent from my MiuiSpeedy
Rooster85 said:
I ended up cutting my usb plug off because of the headache it was causing.
Sent from my MiuiSpeedy
Click to expand...
Click to collapse
Actually you just have to know how to make it stay there's a little trick to it when you close it. You have to kinda pull the thing up a little bit and then slide it in and stays. That's how mine works anyways ..
kbrn said:
Actually you just have to know how to make it stay there's a little trick to it when you close it. You have to kinda pull the thing up a little bit and then slide it in and stays. That's how mine works anyways ..
Click to expand...
Click to collapse
Oh well, too late. The microusb doesn't need to be covered really anyways
Sent from my MiuiSpeedy
I just always wiggle the flap into the port, best case by far would definately recomend. ORDER FROM OTTERBOXS WEBSITE, when it first came out I tried it from amazon (it was $10 less) but the expected shipping date was in june.
No I'm not using Tapatalk... I'm using the XDA Premium app, cause I got balls.
Be careful with the otterbox guys, dropped mine for the first time today and 3 of the 4 clips to hold the back on broke, making the case absolutely useless..... waste of 30 bucks!
Sent from my MiuiSpeedy
When. That happens call otterbox and they will no auestions asked replace it usually takes 1week shipping I've had 5 so fardo this and most recently they sent me 2x so I don't need to calll next timeill. Be prepared...love this company
Sent from my PG06100 using xda premium
+1 to that . They have like you said Replaced mine about 4x's. Never once asked for anything but my address. Best company ever . Have since bought Otter Boxes for all my Devices.
I got this case mid August, and about a week ago, I dropped it. While in free fall, the top of the case just fell off my phone and broke in half. Sad thing is, I dropped it from about 2 feet. But yes, I called it in, and they are sending me in another, just have to watch out for my phone a bit more! (At least I get to replace the screen protector, put it on kinda bad, XP
After trying several cases for my Nexus 7, knowing there aren't any specifically for the Nexus 7 at any retail stores, this was the best one I've come across. It will hold me over until an official case comes out (I've kept the receipt so I can return it). I just can't have such an awesome piece of tech sitting around without a case and without the ability to use it as a stand for viewing. The leather is genuine and the case is simply gorgeous. I love the way if holds the tablet without the clamps/rubberized holding mechanism actually rubbing or touching the bezel. All ports are accessible while it is in the case and the power/volume buttons are very easily accessible.
Found it at Fry's this morning on the way to work but it will set you back $59.99. One of the best portfolio stand cases I've ever owned for any of my devices. High end.
http://www.frys.com/product/7190052?site=sr:SEARCH:MAIN_RSLT_PG
Here are some pictures I just took of it from various angles.
iamsupreme said:
After trying several cases for my Nexus 7, knowing there aren't any specifically for the Nexus 7 at any retail stores, this was the best one I've come across. It will hold me over until an official case comes out (I've kept the receipt so I can return it). I just can't have such an awesome piece of tech sitting around without a case and without the ability to use it as a stand for viewing. The leather is genuine and the case is simply gorgeous. I love the way if holds the tablet without the clamps/rubberized holding mechanism actually rubbing or touching the bezel. All ports are accessible while it is in the case and the power/volume buttons are very easily accessible.
Found it at Fry's this morning on the way to work but it will set you back $59.99. One of the best portfolio stand cases I've ever owned for any of my devices. High end.
http://www.frys.com/product/7190052?site=sr:SEARCH:MAIN_RSLT_PG
Here are some pictures I just took of it from various angles.
Click to expand...
Click to collapse
Nice! Any negatives that you can tell aside from price?
brianbrain said:
Nice! Any negatives that you can tell aside from price?
Click to expand...
Click to collapse
None, which is hard to say about most cases. I've always had something I've disliked about a case but have dealt with it. I've also always went for the cheaper the better in the past. This case is truly a "you get what you pay for" case. The way it holds the very edges of the tablet is my favorite part. It looks like it is floating in the case and the parts that hold the tablet in place never really become part of the view. The access to all buttons and inputs as well as the quality of the leather are great. The actual stand aspect allows for infinite viewing angles and never feels cheap, like the stand portion is going to collapse at any moment.
This case looks really nice. I personally want a colored case though and not the standard brown/black. Also, I'd rather pay a bit more for a case that I really like and thats going to last me a while then buy a cheap case that I'm not that into, deciding that Im not satisfied with it and having to buy more. So if I see something that I fall in love with then I don't mind pulling the trigger as long as its not 100+
iamsupreme said:
None, which is hard to say about most cases. I've always had something I've disliked about a case but have dealt with it. I've also always went for the cheaper the better in the past. This case is truly a "you get what you pay for" case. The way it holds the very edges of the tablet is my favorite part. It looks like it is floating in the case and the parts that hold the tablet in place never really become part of the view. The access to all buttons and inputs as well as the quality of the leather are great. The actual stand aspect allows for infinite viewing angles and never feels cheap, like the stand portion is going to collapse at any moment.
Click to expand...
Click to collapse
Nice. It fits perfectly? Usually cases with the plastic clips are pretty picky about what they'll work with. If so, I'm thinking about buying one of these gtab 2 7.0 cases and adding a "smart cover" magnet to it.
brianbrain said:
Nice. It fits perfectly? Usually cases with the plastic clips are pretty picky about what they'll work with. If so, I'm thinking about buying one of these gtab 2 7.0 cases and adding a "smart cover" magnet to it.
Click to expand...
Click to collapse
Here's how well it fits Very securely! I'm actually shaking the case while I hold it upside down. Talk about making your heart jump a bit!
are you sure? I tried the same case and it doesn't fit too well, but its the best one
the corners are still lodged
iamsupreme said:
Here's how well it fits Very securely! I'm actually shaking the case while I hold it upside down. Talk about making your heart jump a bit!
Click to expand...
Click to collapse
haha, very nice. I may have to see how some of the gtab 2 7.0 cases fit myself. Nice to see you also brought your new baby to work with you today :good:
darthchilli said:
are you sure? I tried the same case and it doesn't fit too well, but its the best one
the corners are still lodged
Click to expand...
Click to collapse
I just pulled the edges on the 4 rubber ends out slightly, if that makes sense, and when the tablet was in place, they wrapped perfectly around each corner of the tablet. It takes a tiny bit of "fitting", but once it's on, it's all good.
brianbrain said:
haha, very nice. I may have to see how some of the gtab 2 7.0 cases fit myself. Nice to see you also brought your new baby to work with you today :good:
Click to expand...
Click to collapse
I had to bring it to work! It definitely is my new baby. Tethered 4G connection from my Galaxy Nexus Streaming music while getting my work on.
Sexy! The case too!
Thanks for sharing, that case looks made to order on the Nexus 7. :good:
How about the speaker in the back, is it covered or are there holes for it?
There are no holes for the speaker. I did a test at max volume and I have no idea why but it sounds louder with it in the case then out of the case. It could be the way it's configured with the speaker near flush but with a decimeter or so gap. I know with my phones and tablets that they tend to sound louder when they are angled near a wall and I seem to get the same effect with this case.
Sent from my Nexus 7 using xda app-developers app
iamsupreme said:
There are no holes for the speaker. I did a test at max volume and I have no idea why but it sounds louder with it in the case then out of the case. It could be the way it's configured with the speaker near flush but with a decimeter or so gap. I know with my phones and tablets that they tend to sound louder when they are angled near a wall and I seem to get the same effect with this case.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
A decimeter is 10 centimeters...
mewantnexus7 said:
A decimeter is 10 centimeters...
Click to expand...
Click to collapse
Okay. My point is that it's less than a centimeter. Maybe a millimeter or so. Enough tiny space to actually amplify the sound
Sent from my Nexus 7 using xda app-developers app
rediculous price! that's 25% of the tablet. I've seen much better looking case off amazon.
qpqpqp said:
rediculous price! that's 25% of the tablet. I've seen much better looking case off amazon.
Click to expand...
Click to collapse
Link? Cause I haven't seen any. All those cheap amazon cases look cheap and tacky IMO.
http://www.amazon.com/gp/aw/d/B0083...4&linkCode=as4&ref_=as_li_ss_til&tag=noref-20
i bought this elcheapo case for now, at least they have 2 day prime shipping
This case is very similar to the one you bought, but is significantly cheaper.
http://www.yourpoetic.com/p/157/hardback-samsung-galaxy-black
The company has a case specifically for the N7, but no pictures of the N7 in a case. I'm guessing their N7 is waiting to be delivered too. Haha. Anyway, I really like the floating look, and will probably be getting this one.
masterofmayhem said:
This case is very similar to the one you bought, but is significantly cheaper.
http://www.yourpoetic.com/p/157/hardback-samsung-galaxy-black
The company has a case specifically for the N7, but no pictures of the N7 in a case. I'm guessing their N7 is waiting to be delivered too. Haha. Anyway, I really like the floating look, and will probably be getting this one.
Click to expand...
Click to collapse
People on other threads have been linking to Cases listed on Amazon and Ebay with that very similar look (they probably all use the same stock photos) with prices ranging from $10 to $20. Even cheaper.
http://www.amazon.com/MoKo-Slim-fit...?s=electronics&ie=UTF8&qid=1342489646&sr=1-12
http://www.amazon.com/i-Blason-Google-Tablet-Leather-Orange/dp/B008H3PAP2/ref=reg_hu-rd_add_1_dp
http://www.amazon.com/Poetic-HardBa...turer/dp/B008IEGS9W/ref=sr_1_24?s=electronics
I don't know, may be not the same quality but it's hard to judge from photos, or even the prizes.
Only way to judge is hand-on experience like the OP's case, his case looks good also because when the back holds on to four corners only, whereas these ones are a bit 'uneven' (when viewed in portrait mode) : p
I would perfer something that holds on to the edges of Nexus 7 only, like the Official Case or this:
http://www.amazon.com/MoKo-Folding-...ction/dp/B007SA0F7S/ref=sr_1_22?s=electronics
Here's the case:
http://www.amazon.com/gp/product/B007S9ZSGW/ref=oh_details_o06_s00_i00
It has all of the correct cutouts. I also like that the speaker cutout is open, as opposed to a bunch of holes like I've seen in other cases. It does add some bulk due to the fact that it can rotate 360 degrees, but it not enough that I can't slip it in my rear pant pockets. It has a loop for the stylus, as well as the magnet wake/lock. It also doesn't have the flaw that other cases have where it locks the tablet when you fold the cover back against itself. I like the white stitching and the fact that it doesn't cover the bezel, which is a deal breaker for me, since covered bezels tend to hinder you when navigating the UI. It also has deep grooves so that it doesn't slip when you have it propped open. Also, when in Portrait mode, you can only use it on the last groove. Any of the other 2 grooves can't support it. When it is on the last groove, I can use it without feeling like it's going to fall back, so it's supported very well in that aspect.
This is the same case that I have for my Blackberry Playbook, and on that back of the Playbook, it has the Blackberry Logo, which you can see through that open hole in the back so it looks nice. On the Nexus, there's no logo or anything on the back that shows through the hole, so I wish that it was covered for the Nexus version. Another small gripe would be the location of the Stylus loop.....if you have the case open and you have a stylus in it, the tab will be at a slight angle. I tested it and it doesn't take away from the sturdiness of it, just a small observation.
All in all, I'm happy with it so far. The seller refunded me the money since I was supposed to receive it last week and it got lost misplaced somewhere in shipping and ended up getting routed to Cali first before coming here, so I give him props for great customer service.
Nice review! The case looks better than I had imagined.
I got the same case delivered on Saturday. Works well. Feel a lot safer carrying it around to and from work now.
I may get the slim fit version as well at some point so it isn't quite as thick, but it does feel solid in this thing.
I notice you have a skin on the back of your nexus. Does it get in the way with the case at all, and if you pull the tab out of the case, has it mangled the skin at all on any pressure points?
I have a skin as well but am reluctant to put it on for this reason, and being that the back is rubberized i dont feel like it really needs it in the first place.
Thanks for the review. Really wish they had more color choices! I want a case that sits portrait (I read a lot) & landscape (Netflix). I already have a case for now, but I'm looking to replace it with one that does everything I want... like this one! I'll wait it out a bit & see if they come out with more colors.
regalpimpin said:
I got the same case delivered on Saturday. Works well. Feel a lot safer carrying it around to and from work now.
I may get the slim fit version as well at some point so it isn't quite as thick, but it does feel solid in this thing.
I notice you have a skin on the back of your nexus. Does it get in the way with the case at all, and if you pull the tab out of the case, has it mangled the skin at all on any pressure points?
I have a skin as well but am reluctant to put it on for this reason, and being that the back is rubberized i dont feel like it really needs it in the first place.
Click to expand...
Click to collapse
Yes, I have an XtremeGuard body protector on it and it doesn't get in the way. I've taken it out of the case a few times and the protector's not bunching up. The protector's been on the Nex7 for over a week, so it's cured pretty well. I wouldn't try it on a fresh protector install. I'd give it about a week so that it sets right before putting it in a case like this.
Prey521 said:
Here's the case:
http://www.amazon.com/gp/product/B007S9ZSGW/ref=oh_details_o06_s00_i00
It has all of the correct cutouts. I also like that the speaker cutout is open, as opposed to a bunch of holes like I've seen in other cases. It does add some bulk due to the fact that it can rotate 360 degrees, but it not enough that I can't slip it in my rear pant pockets. It has a loop for the stylus, as well as the magnet wake/lock. It also doesn't have the flaw that other cases have where it locks the tablet when you fold the cover back against itself. I like the white stitching and the fact that it doesn't cover the bezel, which is a deal breaker for me, since covered bezels tend to hinder you when navigating the UI. It also has deep grooves so that it doesn't slip when you have it propped open. Also, when in Portrait mode, you can only use it on the last groove. Any of the other 2 grooves can't support it. When it is on the last groove, I can use it without feeling like it's going to fall back, so it's supported very well in that aspect.
This is the same case that I have for my Blackberry Playbook, and on that back of the Playbook, it has the Blackberry Logo, which you can see through that open hole in the back so it looks nice. On the Nexus, there's no logo or anything on the back that shows through the hole, so I wish that it was covered for the Nexus version. Another small gripe would be the location of the Stylus loop.....if you have the case open and you have a stylus in it, the tab will be at a slight angle. I tested it and it doesn't take away from the sturdiness of it, just a small observation.
All in all, I'm happy with it so far. The seller refunded me the money since I was supposed to receive it last week and it got lost misplaced somewhere in shipping and ended up getting routed to Cali first before coming here, so I give him props for great customer service.
Click to expand...
Click to collapse
Picture #3, how did you get traffic webcam as widget? Seems useful.
taC nayN said:
Picture #3, how did you get traffic webcam as widget? Seems useful.
Click to expand...
Click to collapse
Ah, that's not a traffic cam widget....that my News360 App widget and the headline was for an overturned truck on a highway near my house lol
LovelyLush said:
Thanks for the review. Really wish they had more color choices! I want a case that sits portrait (I read a lot) & landscape (Netflix). I already have a case for now, but I'm looking to replace it with one that does everything I want... like this one! I'll wait it out a bit & see if they come out with more colors.
Click to expand...
Click to collapse
I'm OK with the black case.....never been a fan of colorful cases. If I had to pick 1 other color, it would probably be like a dark blue.....nothing girly LOL
Nce review ty, I like the case seems decent for protection...even tho a tad thick. I think I well get this one even so based on the review plus I like the look.
Nice right up. Off subject what ROM are you running?
superman.namrepus said:
Nice right up. Off subject what ROM are you running?
Click to expand...
Click to collapse
Modaco JR6 with the Motley Kernel....runs like gangbusters!!
Prey521 said:
Modaco JR6 with the Motley Kernel....runs like gangbusters!!
Click to expand...
Click to collapse
Haha, that was going to be my question
Metalor696 said:
Haha, that was going to be my question
Click to expand...
Click to collapse
I have switched in the last few weeks to the Paranoid Android ROM with the Trinity Kernel. It runs great.
Thought about this case as well, but went with the official travel case.
Bought this case because of your review. It's exactly what I was looking for. Thanks.
Sent from my Google Nexus 7 using Tapatalk 2
I have a similar one bought off ebay. I'm happy with it. The only downside of that case is the circular bit at the back where it rotates.It can potentially scratch the back of the Nexus 7 so I have put a clear protective plastic on the back of the N7.
Just bought this. Came in the mail (pretty quick shipping to Ontario), and I'm really impressed with it:
http://www.amazon.ca/gp/product/B00GW3FMPW/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
Very slim, the cover wakes and sleeps properly when it's opened and closed, stitching is flawless... all in all, a really high quality case. Very happy with it, even after owning for a week or so.
Only one complaint: the case is missing a couple of features compared to the one pictured in the ad. There is no cutout for the charging port (I plan to add this myself -- easy fix), and there is also no hand strap. Not huge losses in my opinion.
Deal breaker....
Trevor_g said:
Just bought this. Came in the mail (pretty quick shipping to Ontario), and I'm really impressed with it:
http://www.amazon.ca/gp/product/B00GW3FMPW/ref=oh_details_o01_s00_i00?ie=UTF8&psc=1
Very slim, the cover wakes and sleeps properly when it's opened and closed, stitching is flawless... all in all, a really high quality case. Very happy with it, even after owning for a week or so.
Only one complaint: the case is missing a couple of features compared to the one pictured in the ad. There is no cutout for the charging port (I plan to add this myself -- easy fix), and there is also no hand strap. Not huge losses in my opinion.
Click to expand...
Click to collapse
I think that the missing charging hole would be a deal breaker for me. Especially since they advertised it as a feature. I hate companies that basically lie in their ads. Cutting into what looks like formed leather might not be such a good idea. But, hey, it it works for you, all the best. The Moko case I have has the charging hole, and it is very convenient. :highfive:
got the same on ebay for like 15 US dollars, its not great but its cheap so i didnt think too much of it
I am still looking for a bumper case or skin for this tablet. It seems pretty rare...
Seems like a good case, although no charging hole would probably be a miss for most people.
AngryDinosaur said:
got the same on ebay for like 15 US dollars, its not great but its cheap so i didnt think too much of it
Click to expand...
Click to collapse
Same here, mine was shipped directly from China. No issues, arrived as promised. No charging hole on this one either.
618$ lol wtf
Sent from my K00C using Tapatalk
I have used this keyboard for the past week and a half, and I thought I'd share my thoughts about it. First off, I bought this off Amazon http://www.amazon.com/Exact-Xperia-Tablet-TypeFOLIO-Series/dp/B00K1L2JA2 for what I felt was a good price and free shipping. Many of my praises will come in light of the great value the case offers.
The outside of the case is a faux leather, but feels more like vinyl. It manages to look pretty professional though. The Xperia Z2 slides right in, and of course with the keyboard the case adds some heft and weight. It becomes much like a small laptop, but still easily carry-able in bag. The keyboard, as expected, is a bit shrunk but roomier than I thought. I adjusted to typing on it within a couple of hours. The stand works well, feeling sturdy and stable. The Bluetooth also connected without a hitch. And finally, the keyboard is removable, held in place by magnets, in case you want to ditch the keyboard and just use the case. In all, I am quite happy with the purchase and it makes forum browsing and emails so much easier on the tablet. Anyone looking for a keyboard case on the cheap should definitely take a look at this one.
hamlettime said:
I have used this keyboard for the past week and a half, and I thought I'd share my thoughts about it. First off, I bought this off Amazon for what I felt was a good price and free shipping. Many of my praises will come in light of the great value the case offers.
The outside of the case is a faux leather, but feels more like vinyl. It manages to look pretty professional though. The Xperia Z2 slides right in, and of course with the keyboard the case adds some heft and weight. It becomes much like a small laptop, but still easily carry-able in bag. The keyboard, as expected, is a bit shrunk but roomier than I thought. I adjusted to typing on it within a couple of hours. The stand works well, feeling sturdy and stable. The Bluetooth also connected without a hitch. And finally, the keyboard is removable, held in place by magnets, in case you want to ditch the keyboard and just use the case. In all, I am quite happy with the purchase and it makes forum browsing and emails so much easier on the tablet. Anyone looking for a keyboard case on the cheap should definitely take a look at this one.
Click to expand...
Click to collapse
Nice pics. What is the quality of the keyboard? Does it feel cheap? Do you type on it withour problems, mistypes or other error that buttons dont work or something?
And what about the angle, can you adjust it or is the angle ont he picture fixed without possible change?
Stirius said:
Nice pics. What is the quality of the keyboard? Does it feel cheap? Do you type on it withour problems, mistypes or other error that buttons dont work or something?
And what about the angle, can you adjust it or is the angle ont he picture fixed without possible change?
Click to expand...
Click to collapse
I've have had no issues with the keys themselves, and the quality is adequate but doesn't feel entirely premium. The stand only sits at that one angle, but I find it comfortable to use.
You cannot use headphones with this case, right?
Would've been great with a small touchpad, does that exist I wonder for android tablets?
Thinking of buying this off Amazon to go with my new tablet for school. How does charging the tablet with the case work? Any clue on battery life for the keyboard and what type it takes? Finally how about a mouse recommendation? Yeah sounds like I should have used a laptop instead with this kind of talk.
Bought the same in blue. Not disappointed at all..