How can I fix Wi-Fi hotspot on Dark Raider? - HTC Vivid, Raider, Velocity

Hey guys. I've had a Raider on Rogers for quite some time, and the Dark Raider rom with KozmikKernel RC1 has been working well for me for what I need. However, the Wi-Fi hotspot hasn't been working for me no matter how many different third-party tethering programs I installed. I'm on the AT&T build.prop. Is there any way I can fix this problem on my current setup, or should I just switch over to stock Rogers ICS and go back to a custom ROM later?
I've also attached a screenshot of what happens on the default hotspot app (My phone crashed while trying to take the screenshot.... weird )

Try the beta 12 from kozmick , or faux 123 (007 kernel) see if that works for ya.

Bigtjmc said:
Try the beta 12 from kozmick , or faux 123 (007 kernel) see if that works for ya.
Click to expand...
Click to collapse
I just installed beta 13 and it didn't work. Also, my phone's performance is now choppier, probably because of the badass governor.

i hope i helped.
i have had the same issue before, and after a lot of reading and searching, i came to figure out what i was doing wrong.
you should keep reading and searching too, you will learn a lot.
but i will tell you what i know and i hope it helps.. it all has to do with the way you flash roms and kernells to your device. if you have already achieved S-off, then your problem may be a lil more difficult,, but if you are just fastboot unlock and rooted.. what you need to do is stract the boot.img of the file that has the kernell inside the rom zip. and flash that separately via fastboot.
place the boot on ur file that ur using to flash stuff, and then use the proper command,
"fastboot flash boot boot.img" in command pront,
if u are confuse, take a look into this guide. http://forum.xda-developers.com/showthread.php?t=1416836
:good:

I've tried 3 different kernels, still getting the same error message as above on DarkRaider. I'm not with AT&T. Any advice?

Reflash the Rom and when its done flash the kernel should fix it

Bigtjmc said:
Reflash the Rom and when its done flash the kernel should fix it
Click to expand...
Click to collapse
Tried that with several ROMs and several kernels - still get the same error. Thought I had it fixed with that world-famous Illuminati ROM, but alas it was not to be.
It has to be an APN problem, in that it's looking for AT&T info and not finding it. That's all I can think of it being...

gfinockio said:
Tried that with several ROMs and several kernels - still get the same error. Thought I had it fixed with that world-famous Illuminati ROM, but alas it was not to be.
It has to be an APN problem, in that it's looking for AT&T info and not finding it. That's all I can think of it being...
Click to expand...
Click to collapse
Only one I ever got the hotspot to work is dark raider buy just clicking on it , only didn't work one time and I reflashed it and the kernel and it worked again I never had to add any thing just click on the hotspot icon .

Bigtjmc said:
Only one I ever got the hotspot to work is dark raider buy just clicking on it , only didn't work one time and I reflashed it and the kernel and it worked again I never had to add any thing just click on the hotspot icon .
Click to expand...
Click to collapse
Are you with AT&T though?

gfinockio said:
Are you with AT&T though?
Click to expand...
Click to collapse
Yea att,

that is what mine looks like , at the top right you can see the active symbol.

On a stock ROM, that's exactly what I see. It works on stock but any modded ROM gives me an error. It works on AT&T, but not on any other carrier. That's what I'm trying to figure out.

Spalla said:
Hey guys. I've had a Raider on Rogers for quite some time, and the Dark Raider rom with KozmikKernel RC1 has been working well for me for what I need. However, the Wi-Fi hotspot hasn't been working for me no matter how many different third-party tethering programs I installed. I'm on the AT&T build.prop. Is there any way I can fix this problem on my current setup, or should I just switch over to stock Rogers ICS and go back to a custom ROM later?
I've also attached a screenshot of what happens on the default hotspot app (My phone crashed while trying to take the screenshot.... weird )
Click to expand...
Click to collapse
Actually I'm using this on my HTC Vivid for tethering!! I did this that a saw on a Vivid ROM thread, I think it was on Dark Raider's..... so I don't deserve any credit, I just want to help. I'm rooted and tried it and it works perfectly!! You can just hit the thank you button.
You'll need SQ Lite Editor:
1) Dialer Storage
2) telephony.db
3) carriers
4) 12 Entitlement 310410
you shoud change the value under "apn" from "broadband" to "pta"
5) Please restart your device and you will get it!!

Related

WTF is going on with Sprint Visual Voicemail

Voicemail not working after flashing to new ROM, tried 3 roms none of them r giving me voicemail. LIQUIDSENSE 2.1, ALOYSIOUS 2.1, NFX hero 2.2, whats the problem. I get a message in tool bar that cant be cleared "A mandatory update is available", but when i try to upgrade i get "General failure. Please try again at a later time"
What to do any suggestions. Ive been hearing bout using google voice, but im kinda lost on that.
PLZ SOMEBODY HELP
cperkins0 said:
Voicemail not working after flashing to new ROM, tried 3 roms none of them r giving me voicemail. LIQUIDSENSE 2.1, ALOYSIOUS 2.1, NFX hero 2.2, whats the problem. I get a message in tool bar that cant be cleared "A mandatory update is available", but when i try to upgrade i get "General failure. Please try again at a later time"
What to do any suggestions. Ive been hearing bout using google voice, but im kinda lost on that.
PLZ SOMEBODY HELP
Click to expand...
Click to collapse
go back to stock 2.1 update the app from there, then backup the .apk (astro file explorer has a tool that allows you to do this) then install it in the other builds
which file is it in? I can't find it
its called com.core.apk or something like that im not sure where it hangs out
cmyasika1 said:
which file is it in? I can't find it
Click to expand...
Click to collapse
thoughtlesskyle said:
its called com.core.apk or something like that im not sure where it hangs out
Click to expand...
Click to collapse
Yeah, it's something like that in system/app
sprint_core.apk in /system/app there may be an odex. i always rm NameOfApp.*
if you delete the apk it may cause problems(maybe. didnt for me but has for others). you also wont be notified of vm's. youll have to call to check. on a 2.1 rom, that is. thats how it worked for me anyway.
personally, my vm isnt working on my new device. like it never set itself up correctly. if anyone should happen to have a link to some instructions to set this up, that would be fantastic. I hate calling the silly people at sprint. thank you
bump this. need help.
vrundmc said:
bump this. need help.
Click to expand...
Click to collapse
Did you try flashing the version in my sig?
theimpaler747 said:
Did you try flashing the version in my sig?
Click to expand...
Click to collapse
i havent tried that as im having annoying problems with my vvm on my device.
http://forum.xda-developers.com/showthread.php?t=855545
guess ill try to use this one here.
tailsthecat3 said:
i havent tried that as im having annoying problems with my vvm on my device.
http://forum.xda-developers.com/showthread.php?t=855545
guess ill try to use this one here.
Click to expand...
Click to collapse
Try flashing my version, let me know how it goes!
theimpaler747 said:
Did you try flashing the version in my sig?
Click to expand...
Click to collapse
Flashed your file...same issue...delay in setting up voicemail... Flashed and restarted. Even tried rebooting. No go. My activation message is stuck in the undelivered box.
theimpaler747 said:
Try flashing my version, let me know how it goes!
Click to expand...
Click to collapse
it didnt work. i removed the original, flashed yours. still have the undelivered message, the activation message. nothing is working, i cant figure it out. and when i called sprint, they reset my vm, so i lost messages and had to set up everything again...
FYI to Impaler, your VVM version in your sig works for those in areas where an official update has not rolled through yet.
Don't know if you are aware, but Sprint recently updated the VVM software to version T.5.1.0.48 (here in TX it was updated the last week of October). Note that Sprint CSR will not be able to help you reset it unless you are on a Sense ROM. Period.
Two options to fix on your non-Sense ROM... there is an updated .apk floating around on these boards (might need to PM someone for it). Get it and install via your file manager.
Or...
Other way is to nandroid your current ROM, then flash a Sense ROM like Fresh's most current. Then, update your PRL and Profile, then go into the VVM and press Menu and update Sprint VVM.
Then, either try to nandroid back to your original ROM and check to see if that does it (haven't tried that, but it might work)... or else... yes, you will need to pull the updated com.coremobility.app.vnotes from the Sense ROM and install the pulled .apk into your new ROM.
Hope this helps.
mr. implaler, I have used yours for the last weeks successfully, so thank you. I just ran into the same problem with the mandatory upgrade, and it is an update i did before I rooted my phone. the VM did work this morning on MUIU but i loaded MYN and that is when my issue started.
Hope someone can firgure it out
thanks again implaler
mine just actually updated and works and phone didn't unroot
vrundmc said:
Flashed your file...same issue...delay in setting up voicemail... Flashed and restarted. Even tried rebooting. No go. My activation message is stuck in the undelivered box.
Click to expand...
Click to collapse
Here is my solution.
http://forum.xda-developers.com/showthread.php?t=855545
I had 9016 in the blocked texts list. Hope this helps you.
Excellent...let me add to this...
I suppose using variations of ROMS that don't include VVM and block 9016 caused this issue.
You can unblock 9016 by going to your account online, under "My Devices," then "My Preferences." Scroll down to the "Limits and permissions" section. You will see the "Block Texts" link there.
vrundmc said:
Flashed your file...same issue...delay in setting up voicemail... Flashed and restarted. Even tried rebooting. No go. My activation message is stuck in the undelivered box.
Click to expand...
Click to collapse
tailsthecat3 said:
it didnt work. i removed the original, flashed yours. still have the undelivered message, the activation message. nothing is working, i cant figure it out. and when i called sprint, they reset my vm, so i lost messages and had to set up everything again...
Click to expand...
Click to collapse
Hmm... I still can't tell if this is a Sprint or a root issue....
alaman68 said:
mr. implaler, I have used yours for the last weeks successfully, so thank you. I just ran into the same problem with the mandatory upgrade, and it is an update i did before I rooted my phone. the VM did work this morning on MUIU but i loaded MYN and that is when my issue started.
Hope someone can firgure it out
thanks again implaler
Click to expand...
Click to collapse
No problem, glad it worked well for you
jedijackie said:
FYI to Impaler, your VVM version in your sig works for those in areas where an official update has not rolled through yet.
Don't know if you are aware, but Sprint recently updated the VVM software to version T.5.1.0.48 (here in TX it was updated the last week of October). Note that Sprint CSR will not be able to help you reset it unless you are on a Sense ROM. Period.
Two options to fix on your non-Sense ROM... there is an updated .apk floating around on these boards (might need to PM someone for it). Get it and install via your file manager.
Or...
Other way is to nandroid your current ROM, then flash a Sense ROM like Fresh's most current. Then, update your PRL and Profile, then go into the VVM and press Menu and update Sprint VVM.
Then, either try to nandroid back to your original ROM and check to see if that does it (haven't tried that, but it might work)... or else... yes, you will need to pull the updated com.coremobility.app.vnotes from the Sense ROM and install the pulled .apk into your new ROM.
Hope this helps.
Click to expand...
Click to collapse
Ok cool, well glad it worked for a few people

[INVALID] Root method deprecated.

This thread is no longer valid. Please reffer to this guide -> Here
Reffer to post above.
Reserved for thanks let me know if you need testing phones
Sent from my MB860 using XDA App
ChongoDroid said:
Reserved for thanks let me know if you need testing phones
Sent from my MB860 using XDA App
Click to expand...
Click to collapse
Will definately need testing. I got the process down 100% though, just the script will require some testing so please stay posted.
!:-D Thank you in advance!
Sent from my rooted and frozen Bell MB860!
GREAT!
we can get some ROMs going with an sbf with root as a backup and Nandroid backup to go all the way back to stock in case you need to return the phone.
also - we can edit the frameworks to get rid of the BS massive carrier title in the notification bar.
will i still be able to install this theme http://forum.xda-developers.com/showthread.php?t=1041450 or at least a black notification bar? thanks
erik10002 said:
will i still be able to install this theme http://forum.xda-developers.com/showthread.php?t=1041450 or at least a black notification bar? thanks
Click to expand...
Click to collapse
Most likely the people making those would have to get the updated framework files and redo the themes to make it work with new firmware. If you really need the theme then i'd recommend waiting for a bit to give people time to make some stuff for the update before you install it. Having root is a good start to getting there though
refresh refresh refresh.......................
my apologies, im just a lil we bit to excited to get this script!
erik10002 said:
will i still be able to install this theme http://forum.xda-developers.com/showthread.php?t=1041450 or at least a black notification bar? thanks
Click to expand...
Click to collapse
I think we will need to deodex first and repackage the theme first. Correct me if I'm wrong. Root is always the first step but the important thing here as stated above is that bell users can use cwm to backup bell then flash to this telstra verson and root to install cwm and recover to bell if necessary. I'm sure someone will port a theme with a dark bar soon This rom also has minor improvements such as 2.2.2 and hspa fix (or so the small tester army is saying).
Lol, I can't seem to type fast enough to get a response out...yesssss, refresh!
Sent from my rooted and frozen Bell MB860!
raybond25 said:
Most likely the people making those would have to get the updated framework files and redo the themes to make it work with new firmware. If you really need the theme then i'd recommend waiting for a bit to give people time to make some stuff for the update before you install it. Having root is a good start to getting there though
Click to expand...
Click to collapse
raybond25 i sent you a PM don't know if you got it but basiclly do i have to wait for a new set of deodexed files and then also have to wait for the theme to be compatible with this SBF? thanks
EDIT: also i don't mind waiting for a few weeks for some compatible themes etc. i want my fast upload speeds etc.
erik10002 said:
raybond25 i sent you a PM don't know if you got it but basiclly do i have to wait for a new set of deodexed files and then also have to wait for the theme to be compatible with this SBF? thanks
Click to expand...
Click to collapse
Yes, that is correct. I wasn't really thinking of deodex. I believe the process is essentially the same for every update, so I don't expect it will be long before this is done. If you really like your current theme setup you might as well wait a week or two before installing the new sbf.
raybond25 said:
Yes, that is correct. I wasn't really thinking of deodex. I believe the process is essentially the same for every update, so I don't expect it will be long before this is done. If you really like your current theme setup you might as well wait a week or two before installing the new sbf.
Click to expand...
Click to collapse
already flashing it, lol. i did like the gingerbread theme but i can live with a white notification bar a settings menu for a couple weeks, most everything else i can get to look the same. but it shouldn't take very long to at least get a black notification bar updated to work with this SBF (few days to a week im guessing)
okay i have run into a problem, when i try and sign in to my motoblur account i get the error (an error has occurred, please try again) also i have no data connection (may just have to enter bell APN settings later) but using wifi. can someone help me with this and is there a way to bypass the setup? thanks
EDIT: managed to bypass motoblur setup using this http://forum.xda-developers.com/showthread.php?t=1027994 and i do have to enter bells APN settings but i think the problem was my wifi at the motoblur setup screen, its doing some crazy connect>disconnect>connect>disconnect thing so that is probably why i couldn't set up my motoblur account
EDIT 2: everything is working except the wifi issue but i never use the wifi, waiting for root script so i can restore using titanium backup!
erik10002 said:
okay i have run into a problem, when i try and sign in to my motoblur account i get the error (an error has occurred, please try again) also i have no data connection (may just have to enter bell APN settings later) but using wifi. can someone help me with this and is there a way to bypass the setup? thanks
Click to expand...
Click to collapse
If its like Bell and has skip setup option when you press menu....
If not, read the thread in this forum called something like" using atrix with no SIM or motoblur account"
erik10002 said:
okay i have run into a problem, when i try and sign in to my motoblur account i get the error (an error has occurred, please try again) also i have no data connection (may just have to enter bell APN settings later) but using wifi. can someone help me with this and is there a way to bypass the setup? thanks
Click to expand...
Click to collapse
I never set up my motoblur (on bell version haven't flashed this one yet), I think I just didn't put in my sim card and didn't connect to wifi and it let me bypass it. Bell apn should be easily found.
Sent from my rooted and frozen Bell MB860!
i just installed this rom and running great , set up the rogers APN and all my preferred settings, now just waiting for this root
wont be long
Just working out the final kinks, and testing on a fresh flash to be 100% everything is explained and working perfectly.
I'm going to flash this now, hoping it fixes some issues I was having. Once it gets deodexed I will update my theme ASAP, because I really cant stand the 2.2 look
Great tutorial, thanks!
Can you confirm that we can install cwm and return to the stock bell? ...Just in case we miss the bellbloat
@silent8..amazing...
Canadian goods
Sent from my rooted and frozen Bell MB860!

XT860 - Going back to Chinese ME863 rom?

My phone has come a long way... from stock Bell to Chinese ME863 stock to Brazilian XT860 stock, to Mexican XT860 stock, to bootstrap, to safestrap, back to bootstrap, and onto Liberty ROM (great rom!)
What bothers me is when "Pay Phone" appears when some people call me (research seems to indicate that these people have a name attached to their phone number, and also if the provider allows you (your plan?) to see these).
Anyway, I don't recall the Chinese stock rom behaving in this way, and I'd like to flash back to it, but I can't (RSD lite and even moto-fastboot methods give up at the first flash... the CDT).
Am I stuck in the world of Brazil/Argentina/Mexico stock roms? That's not a bad thing, of course, as they open up other avenues... but the Pay Phone thing is killing me!
Any help/info would be appreciated. Thank You
LaZiODROID said:
My phone has come a long way... from stock Bell to Chinese ME863 stock to Brazilian XT860 stock, to Mexican XT860 stock, to bootstrap, to safestrap, back to bootstrap, and onto Liberty ROM (great rom!)
What bothers me is when "Pay Phone" appears when some people call me (research seems to indicate that these people have a name attached to their phone number, and also if the provider allows you (your plan?) to see these).
Anyway, I don't recall the Chinese stock rom behaving in this way, and I'd like to flash back to it, but I can't (RSD lite and even moto-fastboot methods give up at the first flash... the CDT).
Am I stuck in the world of Brazil/Argentina/Mexico stock roms? That's not a bad thing, of course, as they open up other avenues... but the Pay Phone thing is killing me!
Any help/info would be appreciated. Thank You
Click to expand...
Click to collapse
Do you need to flash all the partitions to fix that issue? I would think either radio.img or system.img would be responsible for this as caller id is network transmitted. Perhaps try motofastboot flash just one or the other of these
I've also heard that some 3rd party apps can fix this issue. Try poking around the market see what you can find. I have heard that this is a rogers issue with unlocked devices, not just the xt860
Sent from my XT860 using xda premium
Flashing radios and testing sounds more fun
Thanks Endo
To fix "pay phone" just call up rogers and have them remove the name display feature that is packaged with call display.
That's it! Btw why not try using the willis111 bell 2.3.6 deodexed on it? The stock 2.3.6 is pretty awesome, good performance and all.
Sent from my XT860 using xda premium
Because I'm stubborn and dont want to call Rogers to remove the feature, I flashed the ME863 radio to my phone (running eclipse rom right now), copied the ME863 libmoto over (thanks dove0rz for dropping that in the forum!) and noticed that i wasnt getting signal.
I then copied dove0rz's ME863 build.prop (but it was made for cm9)... got signal, did the test.. and voila.. no more Pay Phone. Problem is nothing else really works on my phone. LOL.. (i.e. almost all apps FC).
I expected issues, just wanted to see it working.
My question now is... could minor modifications to the original build.prop (of eclipse rom) get my signal up and running? I wish I knew more about the settings in build.prop. I plan on comparing the original build.prop and me863 cm9 build.prop side-by-side to see if there is a magical line or two that needs adjusting. But any input/help by you experts out there would be appreciated.
This issue's been around for a while and is not specific to the XT860, it also exists on other Moto devices, some HTC and LG devices.
I can't test it because I'm not on Rogers... so I don't have the "Pay Phone" issue..
But I know for sure that using a build.prop from a diff device is usually bad.
So try taking the one that comes from whatever ROM you are on, and look for these lines, that's what I need to get CM9 running with signal on my XT860:
rild.libpath=/system/lib/libmoto_ril.so
ro.telephony.disable.globalnwswitch=true
umts.apn_authentication.enable=1
ro.telephony.default_network=3
ro.telephony.ignore.linkiperror=true #note sure if this one is absolutely necessary
Obviously YMMV as I'm on CM9..
But to get signal on anything other than stock, or Brazil or Latam..
I'd start by making sure it's a freshly flashed working ROM then copying the stock libmoto_ril.so and adding/changing the above lines to your build.prop file
And when you say
could minor modifications to the original build.prop (of eclipse rom) get my signal up and running?
Click to expand...
Click to collapse
Do you mean Voice or 3G or both ?
Also here's a quick list of the available SBF files for our phone:
http://sbf.droid-developers.org/umts_solana/list.php
Thanks PM. I updated/added the lines you suggested to a fresh installed Eclipse ROM's build.prop. Also replaced the libmoto_ril.so (and set 644 permissions to both build.prop and libmoto_ril.so of course). Rebooted and didn't seem to work (No signal at all.) Wifi seems to be working OK.
And yes, what I meant for signal was both voice and 3g.
Thanks for your help. I'm still comparing the original build.prop with the me863 cm9 build.prop to see what got it going by simply dropping the cm9 build.prop in... will update if any progress. Not sure if I'll get far because a lot of this is new to me still.
Upload both the build.props? Or search "web diff tool" in google and paste your files in there, that might help isolate the modified lines
And.. Does it even detect the sim card?
I recall seeing the SIM icon at the top of the screen, if for a few seconds. I can't quite recall if/when it went away. I'm going to try again and keep an eye on that. I was staring at the signal bar and crossing my fingers. Haha
Attached is dove0rz's me863 build.prop for cm9, and the me863 libmoto.
Also attached is the Eclipse 2.0 (for D3) original build.prop.
Thanks
So.. just to recap..
You're on Eclipse ROM.. get no signal.. and when you copy the attached cm9 build.prop, this gets you signal.. but everything FCloses?
Do you only have connection issues in Eclipse after flashing the Chinese radio?
PS: To spot the differences between 2 files, try this: www.aldram.com/Diff.aspx
There's also notepad++ with the compare plugin that achieves a similar diff..
You're on Eclipse ROM.. get no signal.. and when you copy the attached cm9 build.prop
Click to expand...
Click to collapse
PLUS the me863 libmoto_ril.so
this gets you signal.. but everything FCloses?
Click to expand...
Click to collapse
Every app I try to run FC's. Things are pretty good if I use Phone or text (only). I had it running like that for a full day because I wanted to check the caller ID. Saw 3 numbers/contacts appear (that would - on the Mexican/Brazil radio say Pay Phone)
Do you only have connection issues in Eclipse after flashing the Chinese radio?
Click to expand...
Click to collapse
Yes. Normally (on the Mexican radio - p2b_solana_umts_solana_iusacell_mx-user-2.3.6-5.5.1-112_SLU-57M-111107-release-keys-Latam-01.xml.zip) what I'd do for my Eclipse install (a fresh wipe/install) is push my Bell stock limoto_ril.so to /system/lib and set permission to 644 - which allows me to add my APN's.
PS: To spot the differences between 2 files, try this: www.aldram.com/Diff.aspx
There's also notepad++ with the compare plugin that achieves a similar diff..
Click to expand...
Click to collapse
I didn't know notepad++ had a compare plugin. Neat. Thanks!
LaZiODROID said:
PLUS the me863 libmoto_ril.so
Every app I try to run FC's. Things are pretty good if I use Phone or text (only). I had it running like that for a full day because I wanted to check the caller ID. Saw 3 numbers/contacts appear (that would - on the Mexican/Brazil radio say Pay Phone)
Yes. Normally (on the Mexican radio - p2b_solana_umts_solana_iusacell_mx-user-2.3.6-5.5.1-112_SLU-57M-111107-release-keys-Latam-01.xml.zip) what I'd do for my Eclipse install (a fresh wipe/install) is push my Bell stock limoto_ril.so to /system/lib and set permission to 644 - which allows me to add my APN's.
I didn't know notepad++ had a compare plugin. Neat. Thanks!
Click to expand...
Click to collapse
Hey, I'm having the same issues you were having. I started with stock Chinese on ME863 flashed to the Canada XT860 (and tried Brasil to) stock, but can't get data of any kind working. No data not 2g not anything. What did you end up doing for a solution.
Likewise, tried to downgrade back to original china retail stock but have the cdt problem.
Thanks, Sorry I know its been a long time since this post.
It might be the build.prop
Sent from my xt862 using xda app-developers app

[Rom][7-4-12][ZV9]Broken Out Revo 2.0 w/ BlitzKrieg Kernel

Hello all! Here it is Broken Out Rom for the LG Revolution!!! It has been fully cleaned out to decrease size and to increase speed. It will continue to be a work in progress! I hope you all enjoy!!!
What is this?
This is a very lightweight rom built both for speed and stability. This rom is based off of the latest LG update to Gingerbread 2.3.6. It is fully deodexed, and debloated. Almost all of LG has been replaced and as time goes by, I hope to remove the rest. Swype has also been changed to the newest Beta. A few items have been replaced with AOSP versions to increase speed and decrease size. Also included is the appwidgetpicker to clean that up.
Click to expand...
Click to collapse
Changelog
v 2.0
Rom:
Updated to ZV9
Updated all Apps
Updated Super User and SU Binary
Sony Xperia S Theme
Replaced Calculator, Calender, and Email with CM7 Versions
Added a Modified Spare Parts DSP Manager and CM File Manager
Cleaned Up Browser Bookmarks
I'm sure there is a lot more I am forgetting lol
Kernel:
Overclocked to 2.1 Ghz (Does not mean your phone can handle it)
Added Smoothass and Smartass2 Governors
Added SIO I/O Scheduler
Added 2 Way Call Recording
Many Other Speed Mods
v 1.1
Fix Problem With 3G
v 1.0
Rom:
Based Off of ZV8 Gingerbread
Deodexed
Zipaligned
Heavily Debloated
Debinged the Browser
Debinged
Remapped Long Press Search For Google Voice Search
Remapped VM Button in Dialer to Google Voice
Custom Boot Animation
AOSP Lockscreen
Power Menu Mod
Added CMScreenshot to Power Menu
Accurate Battery Mod
Center Clock Mod
Cleaned Up Notification Pull Down
Changed Low Battery Pop Up to 1%
CRT Screen Shut Off
Added ADW Launcher
Updated all Apps Including Google Play
Added AppWidgetPicker
Newest Swype Beta
Build.prop Tweaks
Init.d Tweaks
Loopy Smoothness Tweak
Added Sony Bravia Engine
Made My Own Host File From Several Sources to Block Ads
Blocked All CIQ Logs From Verizon and Google (Requires Reboot After Install)
Click to expand...
Click to collapse
Screenshots
Coming Soon
Click to expand...
Click to collapse
How do I install this?
Must be on ZV8 or ZV9 before flashing!
Otherwise you will have Sim problems!
1.) Download the .zip & make sure 4g is enabled.
2.) Place zip in external sdcard
3.) Back up
4.) WIPE DATA!!! (You do not need to wipe if already on BrokenOut!)
5.) Go to install zip from sdcard
6.) Select BrokenOutRevo2.0.zip
7.) Do not wipe data after flashing!!!
8.) Reboot!
9.) To Block CIQ Logs Requires Reboot After Initial Boot
Click to expand...
Click to collapse
Technical Info
This rom includes edits to several jar files, xml's and build.prop edits. As time goes more will be done.
Click to expand...
Click to collapse
Downloads
Rom
v. 2.0 http://d-h.st/hS7
v. 1.1 http://d-h.st/7ef
v. 1.0 http://d-h.st/2EA
Extras
v. 2.0.1 Patch https://dl.dropbox.com/u/54501789/Revo/BrokenOutRevo2.0.1Patch.zip
Backup Assistant https://dl.dropbox.com/u/54501789/Revo/BackupAssistantforBO2.0.zip
Click to expand...
Click to collapse
Special Thanks!!!
DRT054 for donating his old Revolution
majorpay for Long Press Search fix
Beamer9408 for the battery charge idea and the initial thought for center battery
Kane for the Clear button at bottom in pull down idea
"The Gang" for testing and keeping me entertained on irc, if you haven't been by you should!!!
Click to expand...
Click to collapse
Donations
For those that enjoy the work that I have done and would like to support my efforts financially through the donate to me button, any amount is appreciated, but all that I ask is that if you like my work, please hit the thanks button!!!
Click to expand...
Click to collapse
Downloading now, will flash after work. Let you know how it goes!
missing Sim card
Installed fine, but when I get to set up at the language selection it says it needs a Sim card to activate. I have a Sim card in there. Just in case, I removed it, replaced it and rebooted. Still asking for Sim card...any thoughts?
Damn the bad luck!
Got impatient, flashed this at work (step by step, not new to this). Got stuck at the LANG screen, combo'd past it, no SIM detected.
Fwiw, the build looks AWESOME from playing around in it. So quick at stock! Just cant use it as is. : /
Cal8192 said:
Damn the bad luck!
Got impatient, flashed this at work (step by step, not new to this). Got stuck at the LANG screen, combo'd past it, no SIM detected.
Fwiw, the build looks AWESOME from playing around in it. So quick at stock! Just cant use it as is. : /
Click to expand...
Click to collapse
how did you get passed the lang screen?
Just flashed it, problem it say searching for service and unable to get any signal, i rebooted still no luck then i try to switch to 3g but when i go in networks and try to change the networking application setting crashes and shutdown the setting window any ideas anyone.
Thx
Sent from my VS910 4G using XDA
pborner said:
Installed fine, but when I get to set up at the language selection it says it needs a Sim card to activate. I have a Sim card in there. Just in case, I removed it, replaced it and rebooted. Still asking for Sim card...any thoughts?
Click to expand...
Click to collapse
So wait until updated?
Mad respect mt for having this out so fast
Sent from my VS910 4G using XDA
pborner said:
how did you get passed the lang screen?
Click to expand...
Click to collapse
Go to the CM9 thread here in dev, go back a few pages. I think it was volume up, volume down, back, search. I know those are the keys but I may have the order wrong.
KC, I flashed my nandroid and intend to wait a bit. I tell you though, I'm excited. That ***** was fast! Lol!
Cal8192 said:
Go to the CM9 thread here in dev, go back a few pages. I think it was volume up, volume down, back, search. I know those are the keys but I may have the order wrong.
KC, I flashed my nandroid and intend to wait a bit. I tell you though, I'm excited. That ***** was fast! Lol!
Click to expand...
Click to collapse
I got a fix... try re flashing following all instructions, but DO NOT code through the setup lang. screen. Instead select english, allow the sim card to "activate" until it says it is already activated and you see continue with setup process. and then you can just home button, or back button to you homescreen and ta dah!.
I got it first try. lol super fast and sleek ROM mt... Looking forward to updated releases!
kcarden said:
I got a fix... try re flashing following all instructions, but DO NOT code through the setup lang. screen. Instead select english, allow the sim card to "activate" until it says it is already activated and you see continue with setup process. and then you can just home button, or back button to you homescreen and ta dah!.
I got it first try. lol super fast and sleek ROM mt... Looking forward to updated releases!
Click to expand...
Click to collapse
The problem I was having (and I assume the same for pborner) was that the activation failed because of the "lack" of sim.
I fully intend to reflash this (again) when I wake up in the afternoon. Glad it worked for you. Gives me hope for the second chance!
Cal8192 said:
The problem I was having (and I assume the same for pborner) was that the activation failed because of the "lack" of sim.
I fully intend to reflash this (again) when I wake up in the afternoon. Glad it worked for you. Gives me hope for the second chance!
Click to expand...
Click to collapse
Are you on ZV8 already? If not that is probably the Sim problem.
Sent from my VS920 4G using Tapatalk
So excited, but my replacement phone gets here today ... gotta wait for it to get here.
Looks like I have some work to do updating ICK
Sent from my VS910 4G using Tapatalk
I have the same problem going from gingervolt. LTE is on. Wipe data. Flash Broken Out Revo. Restart phone. Phone does not recognize sim. Tried twice. When I go back to GV everything goes fine.
PEOPLE PAY ATTENTION, the man said you have to be on ZV8 before updating to avoid the sim card issue, I am flashing right now to test will report.
Wow, MT, that was fast!
Many thanks for getting this done so quickly. I'll be installing later today!
MIKEOD5785 said:
PEOPLE PAY ATTENTION, the man said you have to be on ZV8 before updating to avoid the sim card issue, I am flashing right now to test will report.
Click to expand...
Click to collapse
Totally missed that line on the original post. My bad.
WORKS FLAWLESSLYUnfortunately, half the people on here DO NOT follow instructions, and they FAIL and CRY about how it doesn't work. MT puts in this hard work, and you SLUGS can't even follow directions. HE SAID VZ8 IS NECESSARY....if he says that WHY THE **** would you flash from GB?
AND THEN WASTE FORUM SPACE. UNBELIEVABLE, this installed first shot with ZERO problems without tricks and without cm9 GARBAGE. 4 G works perfect, NO SIM CARD ISSUES.
LIKE THE MAN SAID, BEFORE FLASHING YOU BETTER HAVE ZV8, IF YOU DON'T, SCREW
Sorry if I am being stupid on this, but...
I would like to jump into this new rom, but with all the different threads now, I must admit I am really confused. Every night now I receive the Software Update failed screen. I am on ZV7 running GingerVOlt 1.3 now.
Anyone kind enough to point me to the right thread to get to ZV8 and then to this rom after. I am lost reading the different threads now. I figured this would be the best thread to get the help. I have flashed many roms and such on this, nook colors, and my 3 Droid Eris phones, so I know how to do the stuff. I am just not seeing which one to go with first.
Also... I am not sure right now if my ADB is running at home or not. Formatted out my laptop a bit back and not sure if I have run it since or not. So anything that is flashable on the phone would be best for me at work.
Does blue tooth work with this ROM?
eghill1125 said:
Sorry if I am being stupid on this, but...
I would like to jump into this new rom, but with all the different threads now, I must admit I am really confused. Every night now I receive the Software Update failed screen. I am on ZV7 running GingerVOlt 1.3 now.
Anyone kind enough to point me to the right thread to get to ZV8 and then to this rom after. I am lost reading the different threads now. I figured this would be the best thread to get the help. I have flashed many roms and such on this, nook colors, and my 3 Droid Eris phones, so I know how to do the stuff. I am just not seeing which one to go with first.
Also... I am not sure right now if my ADB is running at home or not. Formatted out my laptop a bit back and not sure if I have run it since or not. So anything that is flashable on the phone would be best for me at work.
Click to expand...
Click to collapse
use mt's all in one here http://forum.xda-developers.com/showthread.php?t=1566729
all the files needed can be found here http://forum.xda-developers.com/showthread.php?t=1466655
go here to get the rooted stock zv7 rom (flashable) http://forum.xda-developers.com/showthread.php?t=1348637

LTE not working on CM 12.1 for verizon

I recently flashed cm on to my new droid turbo but the one thing that I can not get to work for some reason even after reflashing the image is the LTE on Verizon. Only the 3G works and even that randomly cuts out at times.
Any help would be appreciated.
Thanks
Are you on the latest release of cm 12.1 I was having this issue but updating appears to have fixed it. Make sure you are running the latest radio as well.
How do I know if I am running the latest radio or not?
I am running the latest highly release right now also
Any ideas what might be the problem?
I started having this issue as well. Everything is up to date. I even got a new sim from Verizon, but that did not help.
I have tried factory resets and even trying resurrection remix but it doesn't get 4g either. Also I can't access the apn which might be part of the problem. Maybe. But I can't figure that out either
Sent from my iPad using Tapatalk
I have had the same problem for about a week and a half, and is really starting to frustrate me.
Tried reflashing the radio SU4TL-44, resurrection remix, CM12.1, computerfreek's near stock rom, modifying the apn. Nothing has worked, except computerfreek's rom kept 4g for about a day, then lost it too. Was about to try to get a new SIM from Verizon to try that out, but won't now if it didn't help others.
hghflyr said:
I have had the same problem for about a week and a half, and is really starting to frustrate me.
Tried reflashing the radio SU4TL-44, resurrection remix, CM12.1, computerfreek's near stock rom, modifying the apn. Nothing has worked, except computerfreek's rom kept 4g for about a day, then lost it too. Was about to try to get a new SIM from Verizon to try that out, but won't now if it didn't help others.
Click to expand...
Click to collapse
I'm also having a similar issue. I'm stuck with 3g. Something to note in my case is that instead of the VZWINTERNET APN I have to use the VZWCF apn.
I was able to reflash cm and get lte to work for two days but now it is back to how it was and I can't even access the APN settings. Some how they are hidden.
shadow14cooper said:
I was able to reflash cm and get lte to work for two days but now it is back to how it was and I can't even access the APN settings. Some how they are hidden.
Click to expand...
Click to collapse
Run these commands in a terminal emulator or an ADB shell.
su
am start -n com.android.settings/.Settings\$ApnSettingsActivity
zangent said:
Run these commands in a terminal emulator or an ADB shell.
su
am start -n com.android.settings/.Settings\$ApnSettingsActivity
Click to expand...
Click to collapse
That helped me be able to get into the APN setting menu but I am not sure I would need to change. There are 5 different APN profiles already made and the vzwinternet is the one selected
shadow14cooper said:
That helped me be able to get into the APN setting menu but I am not sure I would need to change. There are 5 different APN profiles already made and the vzwinternet is the one selected
Click to expand...
Click to collapse
I can't help you, I have connection issues too
zangent said:
I can't help you, I have connection issues too
Click to expand...
Click to collapse
The way that i got lte to work for two days was to flash the stock ROM and then flash cm back on the phone. But I don't want to keep doing that every few days to keep lte working. So we need to find another solution
shadow14cooper said:
The way that i got lte to work for two days was to flash the stock ROM and then flash cm back on the phone. But I don't want to keep doing that every few days to keep lte working. So we need to find another solution
Click to expand...
Click to collapse
If it helps you, what I had to do to fix my connection is this:
I had no data. Then I changed an APN from VZWINTERNET to VZWCF (You probably won't need to do that though).
Then, I had 3g, but not 4g. To fix that, I reflashed the Turbo radio image.
If you don't have it, I can give you a TWRP zip I used for the radio image.
Good luck!
zangent said:
If it helps you, what I had to do to fix my connection is this:
I had no data. Then I changed an APN from VZWINTERNET to VZWCF (You probably won't need to do that though).
Then, I had 3g, but not 4g. To fix that, I reflashed the Turbo radio image.
If you don't have it, I can give you a TWRP zip I used for the radio image.
Good luck!
Click to expand...
Click to collapse
If u could send me that it would be great. I got it work again right now by flashing the stock rom and then flashing resurrection remix. LTE has been working the past 24 hrs for now at least.
Sent from my iPad using Tapatalk
zangent said:
If it helps you, what I had to do to fix my connection is this:
I had no data. Then I changed an APN from VZWINTERNET to VZWCF (You probably won't need to do that though).
Then, I had 3g, but not 4g. To fix that, I reflashed the Turbo radio image.
If you don't have it, I can give you a TWRP zip I used for the radio image.
Good luck!
Click to expand...
Click to collapse
Could you post that image? I would really appreciate it. Thanks!
aka848 said:
Could you post that image? I would really appreciate it. Thanks!
Click to expand...
Click to collapse
shadow14cooper said:
If u could send me that it would be great. I got it work again right now by flashing the stock rom and then flashing resurrection remix. LTE has been working the past 24 hrs for now at least.
Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
https://mega.nz/#!OpF00AwQ!jRumvAOcpHMmAQX9QtvlYn2Sz0qMBSzlfxXKKgnKt0k
Just flash it like any other TWRP archive. Good luck!
If that doesn't work, quote this post so I get a notification.
zangent said:
If that doesn't work
Click to expand...
Click to collapse
Didn't work for me unfortunately. I downloaded the zip twice just to be sure, but it was the same radio update that I had used the previously, and still didn't solve my problem. I still have 3g on multiple ROMs.
Anyone else still having this issue?
hghflyr said:
Didn't work for me unfortunately. I downloaded the zip twice just to be sure, but it was the same radio update that I had used the previously, and still didn't solve my problem. I still have 3g on multiple ROMs.
Anyone else still having this issue?
Click to expand...
Click to collapse
I have the same problem so I flashed computerfreaks rom and lte works on that

Categories

Resources