Hello fellow XDA'ers,
With the release of a stable CM9 candidate for the SGH-T849, I wanted to move away from the stock firmware and use a open-source/less-bloatware/pixiedust/unicornmagic firmware. Just like the fat kid squeezing his way into a candy emporium, I ran at the chance to install CM9.
I loaded the page that I had bookmarked for this very purpose:
*I can't post URLs since I am new to XDA, but it is an internal address*
Code:
wiki[dot]cyanogenmod[dot]com/wiki/Samsung_Galaxy_Tab_(GSM):_Full_Update_Guide
I followed the guide for Windows machines. I did not perform any pre-flashing backups, as all data was already backed-up. Furthermore, I'd like to fully format the internal and external SD cards for use with the tablet.
I installed all necessary drivers, and installed Technomancer's ClockworkMod onto the tablet through Heimdall (via download mode). The flash was deemed a success in the command prompt, and the tablet was rebooted by the computer. The blue bar zipped across the tab to show transfer of zImage.
However, after reboot, the tablet is stuck at the T-Mobile loading screen. I force shut down the device by holding the power button, and after shutdown unplug it from the computer.
I turn the tablet back on, and I get the same T-Mobile loading screen. By now, the tablet is looking at me like I'm stupid, which it's fully right in doing. I turn off the tablet by holding the power button, and the tablet turns off.
I try to see the battery level when plugged in via USB-AC power, but I am greeted with a battery icon that has a loading logo.
Before starting this adventure, I made sure the tablet was fully charged.
I can still enter into download mode when connected to the computer. I have only tried Heimdall, and have yet to read up on ODIN.
Relevant device information:
The device was rooted (SuperUser/BusyBox installed)
Model Number: SGH-T849
Firmware Version: 2.2
Baseband version: T849UVJJB
Kernel Version: 2.6.32.9
[email protected] #1
Build Number: FROYO.UVJJB
This is the first time that I have ever tried to flash a firmware onto an Android device. I have successfully flashed my two Nokia N8's with firmwares and have dealt with iPod touch 2Gs jailbreaks, so I am not *completely* computer incompetent. :silly:
I have tried to find the original firmware for the SGH-T849, but all the download links that I have tried to find are either dead or removed. Since only the zImage was replaced, I was hoping to simply re-flash with the factory zImage. Since I can't find the original factory firmware, I have yet to try this option.
I'm not sure what bricked state the tab is in. I'd like to hope it's soft-bricked, but that's probably not the case.
If I need to perform diagnostics on the device (or if any extra informaiton needs to be provided), I can edit this original posting with updated information. I have easy access to a Windows machine, but I may be able to get access to Ubuntu via disk image on another computer.
I don't want to be the jerk who states that "I solved it!" and leaves everyone in the dust: I'll post everything and anything that happens with this problem for future reference.
Other "stuck at loading screen posts" seem very similar to this, but solutions seem to be very divergent. Therefore, I am hoping for some clarity. Considering that the wiki post was designed for the SGH-T849, I think this thread should act as an appendix to the above wiki page for flashing this device.
Thanks,
willing_to_cooperate
Use overcome method.
T849 is the same as P1000 only with different modem.
http://www.teamovercome.net
Read the guide,
Missing pictures can be seen here.
http://forum.xda-developers.com/showthread.php?p=20974872
Follow the picture step by step.
missing files at
http://tabfirmware.com/2012/01/romk...e-7-series-v4-1-0-♫-overcome-kernel-v4-0-0-♫/
Sent from my GT-P1000 using xda app-developers app
dropbox *.png image link is 404'd
Hi Priyana,
The missing pictures provided through the Dropbox link at the thread provided is giving a 404 error. Knowing this, there aren't any pictures to follow.
Does anyone have a link to the pictures that *isn't* dead? Perhaps hosting on imgur or bayimg would sove this issue for future users.
I don't want to move on the Overcome method until I have the pictures.
Thanks,
willing_to_cooperate
priyana said:
Use overcome method.
T849 is the same as P1000 only with different modem.
http://www.teamovercome.net
Read the guide,
Missing pictures can be seen here.
http://forum.xda-developers.com/showthread.php?p=20974872
Follow the picture step by step.
missing files at
http://tabfirmware.com/2012/01/romk...e-7-series-v4-1-0-♫-overcome-kernel-v4-0-0-♫/
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
Hmm.. others can see it, it shouldn't be a drop box.
Here I reattach
Sent from my GT-P1000 using xda app-developers app
Image too blurry
Hi priyana,
The picture looks really tiny with unreadable text. Specifically, it's only 315px wide.
Do you have a better resolution?
Thanks,
willing_to_cooperate
priyana said:
Hmm.. others can see it, it shouldn't be a drop box.
Here I reattach
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
If you search overcome thread you should be able to find.
Nevertheless
http://forum.xda-developers.com/showpost.php?p=25971078&postcount=1316
Sent from my GT-P1000 using xda app-developers app
Hi priyana,
I followed the guide posted, and downloaded all the necessary files (some of the links in the original thread were missing).
Regardless, I downloaded similar files, and cross-checked the SHA-1 hash against what was listed on the Overcome website.
Flashed once (to Samsung factory reset), followed with a second flash to Overcome. Yahoo! :victory:
Thanks again for your guidance, even when I seemed to be a bit of an annoyance.
Again, for those looking to flashing a similar device, I should be holding the files on my computer (just in case). Just in case I need to return the favor.
Cheers!
willing_to_cooperate
priyana said:
If you search overcome thread you should be able to find.
Nevertheless
http://forum.xda-developers.com/showpost.php?p=25971078&postcount=1316
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
Update on my GT-P1000/SGH-T849: T-Mobile to Overcome to CyanogenMod9/CM9
For reference:
Some people may be confused on how to move from Overcome to CyanogenMod.
The Overcome guide gives directions for wiping caches before installing the Overcome ROM. However, in the PDF guide, this is crossed out, as it is handled by a script in the Overcome ROM.
CM9 for the GT-P1000 doesn't seem to have that built in, which would cause a boot loop if the cache isn't cleared before installing CM9 for the GT-P1000. Since you can't pop the battery, force-shut-down the tablet by holding the power key until the tab shuts down.
After this, follow the Overcome guide to the point where the section of clearing caches is crossed-out. At this point, it's probably best to re-stock your tab (as priyana always suggests ad nauseum). Read between the crossed-out lines to clear caches, and install CM9 for the GT-P1000. It would be a good idea to install GApps at the same time using the same install procedure.
Hope this helps someone,
willing_to_cooperate
willing_to_cooperate
I'm going to give your username willing_to_cooperate the test
Unbelievably, I have *exactly to the letter* the same problem you had a few months ago. Like you I have a SGH-T849, and like you was trying to breathe some life into it by flashing it with Cyanogenmod. And sadly, like you I "soft bricked" it, so now all I get is a stuck T-Mobile screen on boot.
I've been trying to follow your lead and use Overcome + Odin to make things boot again, but I'm unable to get most of the files necessary. Anything that links to a multiupload.com address right now are broken links. Does anyone have other ways to access the files needed for the Overcome process?
If you have any insight on the specific step of getting the Tab out of its current bricked state, I'd much appreciate it.
Also, SGH-T849 has been mentioned as needing a "different modem". What/where is the correct file to use for that step?
Thanks,
Ben
It is right there in general section.
Or follow my signature.
Sent from my GT-P1000 using xda app-developers app
Completing a request.
Hello bklass!
I will do one better. In this case, I will deliver. As I type, the RAR package is uploading.
I will PM you a link to the file when I have uploaded the necessary package. The link that I will provide to your account will be valid for no more than 72 hours from the time I send you the link to the RAR package via PM, NOT from the time of this public post.
I do not want to post a public link, as people will blindly download it, hoping something works. Better to reply to this thread to get the required package. That way, there's a sense of order for this device.
The size of the package is ~1.23GB.
There are some extra files there, as I was trying to make a full copy of all possible files (to possibly help other users). Please don't be scared with the different modems, just make sure to PICK THE RIGHT MODEM.... or you may screw up your tablet (which you want to avoid).
There is a PDF guide of the steps required for using the different files. I would print this off/have it open on another computer, and read through it SEVERAL times to understand what you are doing. I am not saying it's hard, it is just very technically detailed. Make sure to have an afternoon free for the entire procedure. There is a point in the guide which I labelled as "start here," as I took a break, and didn't want to lose my specific spot. If you want to break up the procedure over two sessions, that'd be a good place to stop.
I am 99.99% sure that all the files are present in the RAR'd directory. However, if by some clerical error I forgot to include a specific file (which may be in another directory on my laptop), please let me know of the exact filename so it can be added to an updated archive I upload and send to interested users.
Simply referring to a post (that may be outdated, littered with dead links, and people thanking in-reply instead of properly using a button) does NOT help potential users/customers entering the Android family.
All I ask is that you publicly reply to this message (when you get the file and go through the steps) if: (1) the package sent to you is complete, and; (2) the package provided actually works.
If you leave this thread empty with no reply, you're not cooperating...which is against my spirit of "willing to cooperate".
If you would like to install CyanogenMod, there is a highlighted step with a red note, and a red box pointing to the red note. I did that, as it is a VERY important step (specifically, making sure you delete the cache to install CyanogenMod properly, as CM packages do not clear caches from previous installations automatically: it must be done manually by the user).
For reference, I am successful in running CyanogenMod 9.0 (stable).
Happy Flashing!
willing_to_cooperate
bklaas said:
willing_to_cooperate
I'm going to give your username willing_to_cooperate the test
Unbelievably, I have *exactly to the letter* the same problem you had a few months ago. Like you I have a SGH-T849, and like you was trying to breathe some life into it by flashing it with Cyanogenmod. And sadly, like you I "soft bricked" it, so now all I get is a stuck T-Mobile screen on boot.
I've been trying to follow your lead and use Overcome + Odin to make things boot again, but I'm unable to get most of the files necessary. Anything that links to a multiupload.com address right now are broken links. Does anyone have other ways to access the files needed for the Overcome process?
If you have any insight on the specific step of getting the Tab out of its current bricked state, I'd much appreciate it.
Also, SGH-T849 has been mentioned as needing a "different modem". What/where is the correct file to use for that step?
Thanks,
Ben
Click to expand...
Click to collapse
Thanks, got the files.
I will post back to the thread when I have gone through the overcome guide and report how it went. (next week at the earliest)
cheers
priyana said:
It is right there in general section.
Or follow my signature.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
I'm pleased to say that I've successfully unbricked and flashed the Overcome kernel and 4.1 ROM.
My next step is going all the way to CM9...I'm confused on a few aspects-- First, is it correct to assume that I need to flash to a CM9 kernel before flashing the CM9 ROM?
willing_to_cooperate: if that's the case, that might be the file you forgot to include in your excellent rar archive you sent my way. You really went the extra mile on the instructions btw.
Second, there was a mention earlier in the thread it would be a good idea to go back to stock before moving to CM9. If that's the case, why did I install the Overcome ROM in the first place? Was that a wasted step, considering my end goal was CM9?
cheers,
#!/ben
bklaas said:
Thanks, got the files.
I will post back to the thread when I have gone through the overcome guide and report how it went. (next week at the earliest)
cheers
Click to expand...
Click to collapse
bklaas said:
I'm pleased to say that I've successfully unbricked and flashed the Overcome kernel and 4.1 ROM.
My next step is going all the way to CM9...I'm confused on a few aspects-- First, is it correct to assume that I need to flash to a CM9 kernel before flashing the CM9 ROM?
willing_to_cooperate: if that's the case, that might be the file you forgot to include in your excellent rar archive you sent my way. You really went the extra mile on the instructions btw.
Second, there was a mention earlier in the thread it would be a good idea to go back to stock before moving to CM9. If that's the case, why did I install the Overcome ROM in the first place? Was that a wasted step, considering my end goal was CM9?
cheers,
#!/ben
Click to expand...
Click to collapse
The guide was overcome, that is why overcome ROM was flashed using CWM.
But, actually you don't need that.
You only need to Odin flash the Overcome kernel.
That is it. You don't even need to wait for the robotic voice to complete its thing.
Just force it off.
Then boot to recovery.
use that recovery to flash CM9, twice.
You are kind of right, you need CM9 kernel, but it is done by the first flash
(spot the CWM is different from overcome one, after first flash).
Second flash will install CM9.
Then you flash gapps and reboot.
If you reboot after CM9 without gapps, you can still flash gapps later, but you won't get the setup wizard (the one that ask you to set up wifi, put gmail id, choose to use gmail to backup, bla bla)
So just remember, in the future, restock means Odin flash GB-stock-safe.
Then you will want to Odin flash the Overcome kernel because that is the easiest way to install CWM.
From there it is flashing from CWM.
Full success thanks to this thread
I am 100% up and running with CM9 on my SGH-T849 (T-Mobile branded original 7" Galaxy Tab), thanks to the excellent help from willing_to_cooperate and priyana.
FYI, 2 biggest roadblocks to getting this completed were:
1. Inability to find the necessary files because of broken links, downloads found on sites blocked as malware, etc. [SOLVED] by willing_to_cooperate and him putting together an awesome .rar archive of all necessary files, including a critical annotation in the Overcome guide PDF that told me about the necessary step of wiping cache when flashing CM9
2. Inability to find well-written or even correct information about what to do. As a gadget hobbyist, I have been doing Linux stuff for almost a decade. That community tends to be very sharp and focused to task. The android mod community is quite a bit different I'm finding out-- for every thread with good discussion points there are 25 that say "How do I tweak teh andrd better so I can show everyone how kewl I am". I will concede that this just comes with the territory. Someone tweaking their stock T-mobile phone is quite a bit different than someone installing Ubuntu on a laptop. Nevertheless, [SOLVED] again by willing_to_cooperate and priyana on this thread. Kudos to both of you.
For the record, though I jumped through a few more hoops than was required, these were the steps from getting to "soft-bricked" Galaxy Tab SGH-T849 to fully running CM9 w/gapps.
1. Follow Overcome guide documentation to restock stable Gingerbread
2. Follow Overcome guide to flash Overcome kernel 4.0.0 using Odin
3. Boot and connect Tab as USB storage device
4. Copy CM9 and gapps zip files to mounted Tab (which is the internal SD card)
5. Boot into recovery mode (clockwork mod, which was installed in step 2)
6. Wipe flash/cache through Clockwork Mod
7. Install CM9 and gapps through Clockwork Mod
8. Boot and rejoice in the CM9 awesomeness
cheers,
#!/ben
For the record (as you already have CM9 working on your tablet), I did not include CyanogenMod (CM) releases in the package that I sent to you.
The reason I didn't do that is that the CM ROMs are always updating, and it is easier for the user to find the correct and safest location to download the plain CM ROM files.
For those wondering what address I'm referring to:
http://get.cm/?device=p1 "p1" is the code name for the device.
To clarify, the package that I sent is what I used to get my tablet out of stock (T-Mobile) via Overcome, then updating to CM9.0.
You can select stable, release candidate (RC) or nightly from the menu on the left-hand side. If you are just starting, I would strongly suggest you use the most recent stable ROM for your device (that way, you minimize the risk of using a ROM that may still have bugs).
Good to hear of success relating to your device.
To other people that need the package that I sent to bklass (as you cannot find all the files required due to possible broken links that may happen now or in the future), please PM me and refer to this thread.
I will try to re-write the Overcome guide on a long-term "to-do list" that will clearly delimit what point is restocking, and what point is flashing with another ROM. That, or updating the relevant CM wiki page with proper steps. That way, there is no need to search for a PDF or picture file with relevant steps, just refer to the proper steps in the CM wiki link.
When I rewrite the guide, I'll make sure to include files that are required, with relevant MD5 hashes appended.
Regards,
willing_to_cooperate.
bklaas said:
I'm pleased to say that I've successfully unbricked and flashed the Overcome kernel and 4.1 ROM.
My next step is going all the way to CM9...I'm confused on a few aspects-- First, is it correct to assume that I need to flash to a CM9 kernel before flashing the CM9 ROM?
willing_to_cooperate: if that's the case, that might be the file you forgot to include in your excellent rar archive you sent my way. You really went the extra mile on the instructions btw.
Second, there was a mention earlier in the thread it would be a good idea to go back to stock before moving to CM9. If that's the case, why did I install the Overcome ROM in the first place? Was that a wasted step, considering my end goal was CM9?
cheers,
#!/ben
Click to expand...
Click to collapse
> I will do one better. In this case, I will deliver. As I type, the RAR package is uploading.
Hi! Do you still have that RAR file? I followed the steps at the cyanogenmod site and ended up with the same t-mobile image.
I can still connect to my phone typing "adb shell" on the terminal, and execute commands there, but I do not know how to bring it back to life.
Thanks!
If you're using terminology like shell, I'll assume your on a *nix system.
In short, the files are Windows-based, and should have all components.
PM me and I'll send you the link, as I don't want the RAR file publicly posted (I have limited hosting space via Drop box that I don't want slammed by the XDA community).
Cheers!
willing_to_cooperate
Sent from my GT-P1000 using xda app-developers app
I'm having a difficult time getting mine off the boot screen. Odin doesn't recognize it thus the Overcome steps don't work. Any thoughts?
Thanks,
Holy
Holyloktar said:
I'm having a difficult time getting mine off the boot screen. Odin doesn't recognize it thus the Overcome steps don't work. Any thoughts?
Thanks,
Holy
Click to expand...
Click to collapse
Hi Holykotar,
Hmm... Let me troubleshoot. I'll be approaching your problem from a "cross-examination/troubleshooting" perspective. Please answer all the questions below:
1) Are you having a bootloop? That is, tablet boots up, goes to a logo, then repeats until you get bored?
If you can, it may be wise to enter recovery, delete all caches, and re-start the tablet.
The first time I tried going through the steps, I had a bootloop as the caches were incompatible with the ROM. This may be your case, but it is difficult to determine with the limited information that you have provided me.
Therefore, as stated, I would start off by going into recovery, and deleting all caches. If that works, let me know.
2) What version of ODIN are you using?
Later versions may be incompatible. I used Odin3 v1.7 with success on Windows 7 Ultimate. Also, it could be an issue of not starting ODIN with administrative privileges.
3) What OS are you using?
This may seem silly, but good information for people reading this thread. As stated, I used Windows 7 Ultimate.
4) Have you installed the required computer drivers so the tablet is successfully recognized by the computer?
This would fix some interface issues. If the software (ODIN) can't communicate with the tablet (GT-P1000), then it may be a driver issue.
5) What guide are you using? Better yet, do you have all the required files?
If you are using the guide entitled: "The Overcome Experience" (I have it as a PDF), then there shouldn't be any problems. However, if you are having issues with a proper guide, PM me and I will send you a link to download all necessary files to flash the GT-P1000 (T-Mobile version) without any problems. I request that you PM me for the files, as I don't want the download link distributed (as my bandwidth is fast but limited).
Happy Flashing :laugh:
willing_to_cooperate
Related
Hey guys i am starting this thread here as i find there are so many people asking questions and bricking their phones.I just want to help out people and save them from bricking their phones..
i have tried all Froyo based roms available for the captivate.i have good experience in rooting,clockworkmod and flashing roms.I would like to help out all new members here as much possible because just 2 months back i had trouble finding out things...
So what are you guys waiting for ask away....!
P.S:also i kindly request the other senior members and developers here to correct me if i am wrong anywhere and ya i dont want any donations....
Hey, I'm working on something with a similar spirit as this.
A work in progress: self help brick recovery guide
If you would want help out with this. I believe that it could help the q&a and other section of the captivate thread a lot by reducing the number of brick threads
If either of you have experience with web coding, perhaps it would be worthwhile to make up a page that has an interactive checklist of brick steps. Sort of a step-by-step troubleshooter.
For example, the first page could just be the question about whether the phone shows any signs of life at all or not, then have a page with selectable items about the Rom/kernel/modem setup, then move into more specific items.
See the attached zip for what I'm talking about.
speedy_11 said:
Hey, I'm working on something with a similar spirit as this.
A work in progress: self help brick recovery guide
If you would want help out with this. I believe that it could help the q&a and other section of the captivate thread a lot by reducing the number of brick threads
Click to expand...
Click to collapse
Same spirit here mate i am with you lets do it....!
But i will be focussing on problems of members other than bricking and also i believe prevention would be better than cure....!
jmtheiss said:
If either of you have experience with web coding, perhaps it would be worthwhile to make up a page that has an interactive checklist of brick steps. Sort of a step-by-step troubleshooter.
For example, the first page could just be the question about whether the phone shows any signs of life at all or not, then have a page with selectable items about the Rom/kernel/modem setup, then move into more specific items.
See the attached zip for what I'm talking about.
Click to expand...
Click to collapse
I saw the zip and got what you are saying i liked it. I have a decent hold over html & java so i must be able to create that....!
But i will need space to host it....!
Perhaps in lieu of hosting space, save it as an all-in-one zip file and post it on here. You wouldn't need a large amount additional space (I assume) as there probably wouldn't be a huge need for images. If that's the case, it would be all text, which should be fairly small.
jmtheiss said:
Perhaps in lieu of hosting space, save it as an all-in-one zip file and post it on here. You wouldn't need a large amount additional space (I assume) as there probably wouldn't be a huge need for images. If that's the case, it would be all text, which should be fairly small.
Click to expand...
Click to collapse
true it wont be a big zip file......!
I will create it and post it here
Wow jmtheiss you took my idea to the next level, i never though of making it interactive. But that my be the key that really will make it work.
sorry adicool I'm no good with HTML or coding i will have to leave that to you. But I have a knack for graphic design. Plus I can find and collect the images that could be use as examples (ex. like a soft brick screen)
speedy_11 said:
Wow jmtheiss you took my idea to the next level, i never though of making it interactive. But that my be the key that really will make it work.
sorry adicool I'm no good with HTML or coding i will have to leave that to you. But I have a knack for graphic design. Plus I can find and collect the images that could be use as examples (ex. like a soft brick screen)
Click to expand...
Click to collapse
i just created a test version to see if i still remember html just have a look at this attachment below....!
open the test.html first i have just created a working link for rooting others i will be doing soon,tell me what you think of it....!
adicool said:
i just created a test version to see if i still remember html just have a look at this attachment below....!
open the test.html first i have just created a working link for rooting others i will be doing soon,tell me what you think of it....!
Click to expand...
Click to collapse
Looks good to me. Clean, simple, easy to follow.
A good starting point, if you need any help feel free to ask.
Thought here: The one package is good. I'm also thing that we can have each section posted package as a separate package too (along with the whole package). So those who only need one thing like rooting the can just download that section
Hi! I'm new to the forums and need some help. I have stock I897UCKB1, sucessfully rooted and unlocked it. I would like to try out some ROMs, CM7 first. How should i start? I assume i have Eclair/Froyo bootloaders, right? I've installed ROM Manager Premium, clicked flash clockworkmod, and to reboot to recovery but it's only stock recovery. How should i proceed? Also i need some enlightment on bootloaders: if i flash the newest GB ATT bootloaders will every ROM work with it? Thanks in advance!
Go to the general section, there is a thread called "sticky roll-up" in there is a link to a thread called "e: signature verification failed" that is the work around you need for cwm (or any zip) to flash
Or you can flash a froyo kernel that has cwm baked in with odin like speedmod...
I wouldn't mess with bootloaders st this point in your flashing experience that its the only time you risk a real hard brick do leave those alone until you know for sure what you're doing.
I totally forgot about muse, so here's my on take of the guide.
bazarimajom said:
Hi! I'm new to the forums and need some help. I have stock I897UCKB1, sucessfully rooted and unlocked it. I would like to try out some ROMs, CM7 first. How should i start? I assume i have Eclair/Froyo bootloaders, right? I've installed ROM Manager Premium, clicked flash clockworkmod, and to reboot to recovery but it's only stock recovery. How should i proceed? Also i need some enlightment on bootloaders: if i flash the newest GB ATT bootloaders will every ROM work with it? Thanks in advance!
Click to expand...
Click to collapse
I would advice you to first try flashing a few froyo based roms just to gain experience in flashing after that you can move over to GB
as told by my friends here there is a thread here that fixes that cwm problem .!
If you still need help or cant find it do post here and i would be more than happy to help...!whatever you do just dont mess with bootloaders atm as they can cause your device to be bricked...
I would say start off first by flashing cognition 4.5.3....!
speedy_11 said:
A good starting point, if you need any help feel free to ask.
Thought here: The one package is good. I'm also thing that we can have each section posted package as a separate package too (along with the whole package). So those who only need one thing like rooting the can just download that section
Click to expand...
Click to collapse
Hmmm well that can be done !
i have college today i will get started with the html again once i come back....
lets finish this thing soon!
Edit:just finsihed the package for 2.2 only,have a look at the attachment,also its not complete yet but it had basic things...!
studacris said:
Go to the general section, there is a thread called "sticky roll-up" in there is a link to a thread called "e: signature verification failed" that is the work around you need for cwm (or any zip) to flash
Or you can flash a froyo kernel that has cwm baked in with odin like speedmod...
I wouldn't mess with bootloaders st this point in your flashing experience that its the only time you risk a real hard brick do leave those alone until you know for sure what you're doing.
Click to expand...
Click to collapse
adicool said:
I would advice you to first try flashing a few froyo based roms just to gain experience in flashing after that you can move over to GB
as told by my friends here there is a thread here that fixes that cwm problem .!
If you still need help or cant find it do post here and i would be more than happy to help...!whatever you do just dont mess with bootloaders atm as they can cause your device to be bricked...
I would say start off first by flashing cognition 4.5.3....!
Click to expand...
Click to collapse
Thanks, i was able to get CWM to work with speedmod kernel, so i take your advice now and try out some froyo roms!
bazarimajom said:
Thanks, i was able to get CWM to work with speedmod kernel, so i take your advice now and try out some froyo roms!
Click to expand...
Click to collapse
Cool.....!
dont forget to follow the instructions before flashing...
adicool said:
Edit:just finsihed the package for 2.2 only,have a look at the attachment,also its not complete yet but it had basic things...!
Click to expand...
Click to collapse
The information looks good, i saw that on the flash back to stock you didn't put hemdiall. Since linux and mac users cant use odin
Did you take a peak at my attempt with muse?
speedy_11 said:
The information looks good, i saw that on the flash back to stock you didn't put hemdiall. Since linux and mac users cant use odin
Did you take a peak at my attempt with muse?
Click to expand...
Click to collapse
oops i forgot that, i dont use mac so i missed it lol....!
yeah i saw your attempt it was decent enough mate,if you want to try more software try adobe dreamweaver it will help you develop web pages without html
dreamweaver would be great but my current computer wouldn't be able to handle it and i dont have the money for it. muse is free until the final product is done that why im using it.
i pm'ed you but i dont know if it sent
I heard something recently about fileshare sites being shut down...is that what I'm experiencing. Tried to download files from: http://forum.xda-developers.com/showthread.php?t=1359068 and none of the links work. Actually a couple did but said I could only download a file I uploaded myself. I tried downloading from another thread on this site and had the same problem. Any solutions/alternatives? How can I download from the link I posted above?
Thanks!
Firecracker_RC said:
I heard something recently about fileshare sites being shut down...is that what I'm experiencing. Tried to download files from: http://forum.xda-developers.com/showthread.php?t=1359068 and none of the links work. Actually a couple did but said I could only download a file I uploaded myself. I tried downloading from another thread on this site and had the same problem. Any solutions/alternatives? How can I download from the link I posted above?
Thanks!
Click to expand...
Click to collapse
I see a KJ4 link. Have you tried the KJ5 thread? It's the newest one for our 7310.
Hi nirogu325, thanks for replying. This is what I am trying to do:
-Enable adhoc connection so I can use my windows mobile phone as a hotspot for my tabl, and
-Enable USB charging for my tab in my car and elsewhere, not just wall jack.
Based on what I've read, I need busybox (Titanium back up says it's installed but when I downloaded an app called wifiadhocenabler, it says it is not installed. Installing it from the market says I need Nand Unlock and this is where I'm stuck at the moment. Do you know how to perform this on the P7310? Or an easier way to meet the objectives above?
Thanks again
Firecracker_RC said:
Hi nirogu325, thanks for replying. This is what I am trying to do:
-Enable adhoc connection so I can use my windows mobile phone as a hotspot for my tabl, and
-Enable USB charging for my tab in my car and elsewhere, not just wall jack.
Based on what I've read, I need busybox (Titanium back up says it's installed but when I downloaded an app called wifiadhocenabler, it says it is not installed. Installing it from the market says I need Nand Unlock and this is where I'm stuck at the moment. Do you know how to perform this on the P7310? Or an easier way to meet the objectives above?
Thanks again
Click to expand...
Click to collapse
I assume you're on a stock firmware. If I were you, I'd flash this specific version which is already rooted and has busybox as you can read in the OP. Also, flash the v2d version of the motley kernel and go here for the USB charging script and instructions on enabling. I know that last link is for the 10.1, but it is the one motley linked to in the v2b version changelog in his kernel thread.
After my soft brick yesterday, I used Odin to "install" the version you attached in your General Guide post P310XARKJ5_P7310UEKJ5_HOME.tar.md5). That's the one, right?
Anyway, the good news is, I decided to install BusyBox without doing the Nand Unlock (maybe it was already done?), and it worked! The wifiadhocenabler app works now and I have a connection to my wm phone! Yay! Before trying the app (for the sake of onlookers) I tried the other method with the wpa_supplicant, such as the one here: http://androidtablethacks.com/android-tablet-hacks/how-to-enable-adhoc-wifi-on-android-tablets/ and it did not work for me. The app did!
So now, I'll try the kernel you posted above and then the USB charging.
I'm going to look over your general guide to see if I can figure out how to flash. I'm guessing it's the same or similar to when I recovered my tab in Odin...?
Firecracker_RC said:
After my soft brick yesterday, I used Odin to "install" the version you attached in your General Guide post P310XARKJ5_P7310UEKJ5_HOME.tar.md5). That's the one, right?
Anyway, the good news is, I decided to install BusyBox without doing the Nand Unlock (maybe it was already done?), and it worked! The wifiadhocenabler app works now and I have a connection to my wm phone! Yay! Before trying the app (for the sake of onlookers) I tried the other method with the wpa_supplicant, such as the one here: http://androidtablethacks.com/android-tablet-hacks/how-to-enable-adhoc-wifi-on-android-tablets/ and it did not work for me. The app did!
So now, I'll try the kernel you posted above and then the USB charging.
I'm going to look over your general guide to see if I can figure out how to flash. I'm guessing it's the same or similar to when I recovered my tab in Odin...?
Click to expand...
Click to collapse
If you mean flashing a CWM package as the motley kernel, a file goes in the SDcard, you access the CWM Recovery and flash. That's a generic way BUT depending on what you will flash you may have to wipe. That's why I avoided altogether putting generic instructions regarding CWM packages in my guide (instructions may vary between ROM and kernels). Read your flashable package's thread carefully.
kind of like rooting? Yes, do I have to wipe to flash the motley kernel? I'm not seeing the flashable packages thread, can you point me to it?
Firecracker_RC said:
kind of like rooting? Yes, do I have to wipe to flash the motley kernel? I'm not seeing the flashable packages thread, can you point me to it?
Click to expand...
Click to collapse
No, lol. If you want to flash the motley kernel just follow that thread's instructions. I gave you the motley kernel thread link in a previous post. For kernels, no wipe is necessary, for ROMs, yes.
Ok, thank you. lol
Firecracker_RC said:
Ok, thank you. lol
Click to expand...
Click to collapse
You're welcome. Some people have the tendency NOT to wipe while flashing ROMs...yet complain later on the road. Always wipe when it comes to ROMs if you want to avoid issues. The only bugs you will experience are the ones that come with the ROM already. Better safe than sorry.
Ah, that leads me to wonder...When my tab was soft bricked and I used Odin3 and inserted the KJ5 file into the PDA section, and so on (I think that was flashing), was I supposed to do a wipe before I did that? If so, would it be better if I started from scratch again? ...hoping not, but better now than latter I'm thinking.
Firecracker_RC said:
Ah, that leads me to wonder...When my tab was soft bricked and I used Odin3 and inserted the KJ5 file into the PDA section, and so on (I think that was flashing), was I supposed to do a wipe before I did that? If so, would it be better if I started from scratch again? ...hoping not, but better now than latter I'm thinking.
Click to expand...
Click to collapse
No. ODIN clears everything (including kernels, ROMs and CWM Recoveries). Everything back to stock. I was just referring to flashing other custom ROMs (non-ODIN, i.e. CWM flashable) procedures. Stick to the thread instructions in your chosen ROM and you'll be fine. It's just that some don't follow instructions and due to that, they may experience weird bugs.
That's good news, and strange, because after I used Oden3 (in the way I previously described), all my apps and files were still in tact. Does it just affect the system and not the file memory?
P.S. Hey! I'm no longer a noob! lol I just noticed I am now a "Junior Member".
P.S.S. I'm now running my tablet off my wm hotspot while charging it on my pc! woohoo
Firecracker_RC said:
That's good news, and strange, because after I used Oden3 (in the way I previously described), all my apps and files were still in tact. Does it just affect the system and not the file memory?
P.S. Hey! I'm no longer a noob! lol I just noticed I am now a "Junior Member".
Click to expand...
Click to collapse
That is because you didn't check F.Reset Time on the left side of ODIN before flashing. It is advisable to make sure it is checked. Thanks, I'm gonna put that little but important detail in my guide (dunno how I missed that one ). I advise using Titanium Backup (for apps backup) and then ODIN. You might be fine as you are, but if you ever experience something weird then you know.
Firecracker_RC said:
P.S.S. I'm now running my tablet off my wm hotspot while charging it on my pc! woohoo
Click to expand...
Click to collapse
I'm glad you made it!
Thanks for your support. If I ever have some extra change and feel like making a donation, I'll keep you in mind! Hey, where's your donation link anyway? Better get one!
nirogu325 said:
That is because you didn't check F.Reset Time on the left side of ODIN before flashing. It is advisable to make sure it is checked. Thanks, I'm gonna put that little but important detail in my guide (dunno how I missed that one ). I advise using Titanium Backup (for apps backup) and then ODIN. You might be fine as you are, but if you ever experience something weird then you know.
Click to expand...
Click to collapse
My tablet is definitely a little laggy now, but that could be the 3.2 HC. Since I did not check that off, does it mean that it did not install on a clean wipe? I'm wondering if I should just do it while I remember the path to how I got where I'm at now. I doubt I'll remember everything down the road.
I have been making nandroid backups as well as titanium app backups.
Firecracker_RC said:
My tablet is definitely a little laggy now, but that could be the 3.2 HC. Since I did not check that off, does it mean that it did not install on a clean wipe? I'm wondering if I should just do it while I remember the path to how I got where I'm at now. I doubt I'll remember everything down the road.
I have been making nandroid backups as well as titanium app backups.
Click to expand...
Click to collapse
As for donations, nah it's ok, I am no developer. As for the suggestion, it was just that, a suggestion for next time. Keep that in mind. It will become a habit down the road.
Sent from my GT-P7310
nirogu325,
I'm back to do my clean wipe. I performed the wipe/data reset in nandroid and now it's saying there is an update from KJ5 to LA3. Do you still think the custom kj5 is better than the stock LA3? I'm wondering if I should just install the update, root, install the motley kernel and go from there...?
Hope you're well! I still think you should add a donate link...you don't have to be a developer, your assistance/guidance is equally helpful to the community.
While I'm waiting, I flashed http://forum.xda-developers.com/showthread.php?t=1375112 and then I noticed I have the old CMR so I downloaded your updated package: GTab89Files and I cannot paste a single file from that folder onto my tab. I can paste files from other folders, but this one I copy and when I go to paste the paste option is not enabled; if I drag I get a little red circle with a line through it. Any ideas as to why it's rejecting?
(Obvious Noob warning---) A friend helped me root my Thrill, install ClockworkMod Recovery, and then install CM7 on my Thrill. But I would like to try the LG GB release. Is it necessary to backtrack all the way back to stock to do this (i.e. reinstall the stock ROM, reinstall the stock recovery, unroot, etc.)?
My friend tried using the LG upgrade tool on his LG phone without going back to stock and ended up bricking it. He says that usually within a few days of release, a CMR compatible zip file (usually already rooted) appears here on XDA (I haven't seen it), which makes things easier (but obviously he didn't wait for it himself).
Will a zip be possible for the Thrill GB? (The file seems quite large (420MB), so I'm guessing there is a lot of media included.) Or should I just bite the bullet and backtrack?
Rick
Rick Tillery said:
(Obvious Noob warning---) A friend helped me root my Thrill, install ClockworkMod Recovery, and then install CM7 on my Thrill. But I would like to try the LG GB release. Is it necessary to backtrack all the way back to stock to do this (i.e. reinstall the stock ROM, reinstall the stock recovery, unroot, etc.)?
My friend tried using the LG upgrade tool on his LG phone without going back to stock and ended up bricking it. He says that usually within a few days of release, a CMR compatible zip file (usually already rooted) appears here on XDA (I haven't seen it), which makes things easier (but obviously he didn't wait for it himself).
Will a zip be possible for the Thrill GB? (The file seems quite large (420MB), so I'm guessing there is a lot of media included.) Or should I just bite the bullet and backtrack?
Rick
Click to expand...
Click to collapse
I'm assuming that the official update method was used.
Just use this method after downloading the update. No bricking.
SEE THREAD
The Dark Lestat said:
I'm assuming that the official update method was used.
Just use this method after downloading the update. No bricking.
SEE THREAD
Click to expand...
Click to collapse
Thank you for your help!
Rick
Trojan?
Sorry, but as a noob, I can't post in that other thread.
It seems that the shttp3.exe in the LG Flash Package triggers Symantec's trojan detection. Some searching seems to indicate (assuming I'm reading all the cryptic virus sites correctly) that there is something to this, although it seems that different scanners find different trojans/viruses (can't post the link, but Google for "shttp3.exe" and "trojan"). I also found that the web site for this utility is blocked at work, because it's a "malicious site."
Has anyone seen this? Has anyone been able to verify/refute this?
Rick
There is no virus, Lestat would never do that
Sent from my LG-P925 using XDA
Just my .02 .....Get rid of Symantec !! They are known for scaring people into a virus frenzy.. Yes, it is possible that it is seeing it as a potential virus because shttp is a workaround from the usual porting of windows ip services. ...
Correct me if i'm wrong somebody please !!
Get yourself Comodo and save your money...
Regards,
Dwayne
PS: somebody on here has written a script that just uses shttp temporarily while
your doing the flash procedure, and then reverts your host files back automatically after your done. You should try it.
dwaynedman said:
Just my .02 .....Get rid of Symantec !!
Click to expand...
Click to collapse
Symantec isn't really a choice on work PC.
Get yourself Comodo and save your money...
Click to expand...
Click to collapse
I'm sorry I can't give the link yet, but if you'll Google you'll see Comodo classifies shttp3.exe as "ApplicUnwnt.Win32.ServerWeb.SmallHTTP.~A" or "UnclassifiedMalware" (I guess depending on the version). A number of scanners find issues with shttp3.exe. I'm not saying it is infected, only that it is doing something suspicious.
Rick
Rick Tillery said:
Sorry, but as a noob, I can't post in that other thread.
It seems that the shttp3.exe in the LG Flash Package triggers Symantec's trojan detection. Some searching seems to indicate (assuming I'm reading all the cryptic virus sites correctly) that there is something to this, although it seems that different scanners find different trojans/viruses (can't post the link, but Google for "shttp3.exe" and "trojan"). I also found that the web site for this utility is blocked at work, because it's a "malicious site."
Has anyone seen this? Has anyone been able to verify/refute this?
Rick
Click to expand...
Click to collapse
shttp3.exe is in no way a virus. I've scanned with AVG and MalwareBytes Anti-Malware and they check out good.
Back to square one
OK, I seem to be stuck.
With paranoia in tow, I decided to take the long way back to stock. Unfortunately, when I tried to restore the backup of my stock image I made to SD card after installing CMR, the md5 checksum failed. I'm not sure what I can do about this.
So ok, I tried following the above link. The first step is to ensure the su binary is up-to-date. But when I tried this, I get a failure downloading the manifest. This is true for WiFi and HSPA+. I Googled and found a suggestion to delete the su binary. But that didn't help (I'm not sure how it would have helped anyway).
So back to the original question. Can I use the LG upgrade process to upgrade without going backwards (as you can see above, I can't) without bricking the phone? Can I start at step 3 in the link above and succeed?
Rick
The Dark Lestat said:
shttp3.exe is in no way a virus. I've scanned with AVG and MalwareBytes Anti-Malware and they check out good.
Click to expand...
Click to collapse
Thank you, sir. I hope it didn't seem accusing.
Rick
Rick Tillery said:
Thank you, sir. I hope it didn't seem accusing.
Rick
Click to expand...
Click to collapse
It's cool, my friend.
Sent from my Samsung Galaxy S II w/ CM9
Rick Tillery said:
OK, I seem to be stuck.
With paranoia in tow, I decided to take the long way back to stock. Unfortunately, when I tried to restore the backup of my stock image I made to SD card after installing CMR, the md5 checksum failed. I'm not sure what I can do about this.
So ok, I tried following the above link. The first step is to ensure the su binary is up-to-date. But when I tried this, I get a failure downloading the manifest. This is true for WiFi and HSPA+. I Googled and found a suggestion to delete the su binary. But that didn't help (I'm not sure how it would have helped anyway).
So back to the original question. Can I use the LG upgrade process to upgrade without going backwards (as you can see above, I can't) without bricking the phone? Can I start at step 3 in the link above and succeed?
Rick
Click to expand...
Click to collapse
Is it safe to ignore the su version update?
Short of this, can I override the MD5 checksum? I realize that image could be corrupt, but if I'm just going to replace it with the GB release, does that matter?
Rick
You should just put your phone in recovery mode and update through the tool
with your IMEI #. It will give you the latest update !
If you need some help on that I think Lestat or somebody has a write-up
on doing this.
Good luck,
Dwayne
dwaynedman said:
You should just put your phone in recovery mode and update through the tool
with your IMEI #. It will give you the latest update !
If you need some help on that I think Lestat or somebody has a write-up
on doing this.
Good luck,
Dwayne
Click to expand...
Click to collapse
Can you be a bit more specific?
1. By "recovery mode," do you mean into ClockworkMod Recovery, or I should revert to stock (I made a copy of it after I rooted the stock ROM, but before I installed CMR)?
2. By "the tool," do you mean the official LGMobile Software Update, or the LG Flash Package referenced in the link above?
3. By "latest update," do you mean the file directly from LG, or the copy (v20p) linked from the link above?
4. If the latter in both previous questions, which set of steps do I need to follow from the above link? Can I do only 3 (LG Flash Tool), or do I need to follow 1 (Recovery Manager), 2 (Returning to Stock), and 3?
My friend had a different LG phone, with ClockworkMod Recover and CM7 installed. He reverted the CM7 to stock, but did not replace CMR with the stock recovery. Then he used the official LG upgrade method and bricked his phone. I'm trying to avoid this.
Are you saying I don't have to worry about this on the LG Thrill 4G? Can I go straight from the current CMR+CM7 configuration to the LG GB release using the official LG process?
If you mean I should use a different process, can you point me to it? As I mentioned, I run into dead-ends using the method linked above. And I'm not even sure whether I should be doing steps 1, 2 and 3, or if I should just use step 3.
Any and all help is appreciated, but I guess I don't understand the shorthand you're using here, so if you could be a bit more specific, I wouldn't feel so lost.
Rick
Rick Tillery said:
Can you be a bit more specific?
1. By "recovery mode," do you mean into ClockworkMod Recovery, or I should revert to stock (I made a copy of it after I rooted the stock ROM, but before I installed CMR)?
2. By "the tool," do you mean the official LGMobile Software Update, or the LG Flash Package referenced in the link above?
3. By "latest update," do you mean the file directly from LG, or the copy (v20p) linked from the link above?
4. If the latter in both previous questions, which set of steps do I need to follow from the above link? Can I do only 3 (LG Flash Tool), or do I need to follow 1 (Recovery Manager), 2 (Returning to Stock), and 3?
My friend had a different LG phone, with ClockworkMod Recover and CM7 installed. He reverted the CM7 to stock, but did not replace CMR with the stock recovery. Then he used the official LG upgrade method and bricked his phone. I'm trying to avoid this.
Are you saying I don't have to worry about this on the LG Thrill 4G? Can I go straight from the current CMR+CM7 configuration to the LG GB release using the official LG process?
If you mean I should use a different process, can you point me to it? As I mentioned, I run into dead-ends using the method linked above. And I'm not even sure whether I should be doing steps 1, 2 and 3, or if I should just use step 3.
Any and all help is appreciated, but I guess I don't understand the shorthand you're using here, so if you could be a bit more specific, I wouldn't feel so lost.
Rick
Click to expand...
Click to collapse
Remove your battery and keep the phone unplugged
Launch the mobile updater tool
Hold the volume+ button plug the phone in and keep holding the volume+ till the computer downloads the drivers your phone is now in download mode
Once the phone is picked up go to customer support on the LG updater tool and click on recovery phone put your imie number in click check (make sure its the right model) an let the updater tool do its job. Once its done flashing launch into recovery volume- plus power plus 3D button do a complete wipe and factory reset and reboot your phone ... you'll lose cwm and root and be back to full stock
Sent from my LG-P925 using XDA
Bricked?
No joy. Following the steps, the upgrade stopped at 6%. Trying a number of times, it eventually forced me to exit the program (no more restarts). Rerunning the updater (and downloading the 420 MB image yet again on a VERY slow connection) I tried again and again, with different combinations of battery and plug order with power and volume buttons, but nothing worked. Checking elsewhere I found some issues had been reported with Windows Vista/7, so I tried on an XP machine. Now the "Start Updating" bar is red (it was always gray with W7). But now when I try to restore (or even update for that matter), it asks for my S/N (it never did that before) and then says it is "no longer able to upgrade." Reading around, it seems this is an indication of the device being bricked.
Rick
It sounds like you are very close to getting it working Rick.
My update did the same thing, looped over and over until it
finally kicked me out. Just plugging and unplugging the phone etc....
And when my update stuck at 6% the last time, i took my battery out and then in real quick and that seemed to work.
Does the phone still vibrate when you plug the usb cable into it while holding volume..? If it does then I highly doubt that your phone is bricked, just in a semi flashed state....No worries
Should Rick be trying to run LG Updater as administrator ? I didn't, but it might not hurt.
Regards & Luck,
Dwayne
http://forum.xda-developers.com/showthread.php?p=22417769
Have you tried this yet cause if you can get the LG logo to come up then you can reflash the phone and get it working send a pm to the dark lestat he may be able to team viewer you and help you out
Sent from my ****ty supported LG Thrill
dwaynedman said:
It sounds like you are very close to getting it working Rick.
Click to expand...
Click to collapse
I wouldn't have believed you early this morning, but now maybe...
My update did the same thing, looped over and over until it
finally kicked me out. Just plugging and unplugging the phone etc....
And when my update stuck at 6% the last time, i took my battery out and then in real quick and that seemed to work.
Click to expand...
Click to collapse
I tried a bunch of different combinations...none seemed to make the app happy. I finally punted Windows 7 and moved to an XP machine, only to get the "no longer able to update" message. At that point I assumed I was screwed (effectively bricked).
Does the phone still vibrate when you plug the usb cable into it while holding volume..? If it does then I highly doubt that your phone is bricked, just in a semi flashed state....No worries
Click to expand...
Click to collapse
It never really vibrated, but I was able to get back into CMR. Unfortunately NONE of my backups work at all. They all have MD5 checksum failures. I tried a trick I found online and got past that step, only to have it say a failure restoring /system. So much for CMR.
JReeher said:
http://forum.xda-developers.com/showthread.php?p=22417769
Have you tried this yet cause if you can get the LG logo to come up then you can reflash the phone and get it working send a pm to the dark lestat he may be able to team viewer you and help you out
Click to expand...
Click to collapse
Which step? As I mentioned above, I can't even get the first step of the first section (updating the su binary). And if I start at the 3rd section, Symantec prohibits me from using shttp3.exe (I tried to unquarantine it, but it gives a permission error, even as Administrator, when I try to run it), so I'll have to use a different machine.
I was able to reinstall the CM7 3/15 release, so that's something. I was going to restore the stock recovery backup I made, but even that doesn't seem to work. I'm having issue with backups :-(
Rick
i have never been able to restore a backup. i dont know why... but i have tried several times in several different instances.
---------- Post added at 11:56 AM ---------- Previous post was at 11:50 AM ----------
rick tillery, if you want to get your phone back to alive and well i'd suggest doing this:
http://forum.xda-developers.com/showthread.php?t=1558723&page=3
4th post i think
I have tried to use the search but all I get is stuff of on 7 and 9 and I would like to install CM6. Anyone have a link because I just can't find it.
If you just need the CM6.x rom files, I have a boat load of them in my collection linked in my sig. You install it just like you would any other CM rom, ROM first, then the proper gapps file for the rom second _before_ booting. The gapps file you need is "gapps-hdpi-20101114-signed.zip" also in my collection.
good luck
Thanks for the response!
teddyearp said:
If you just need the CM6.x rom files, I have a boat load of them in my collection linked in my sig. You install it just like you would any other CM rom, ROM first, then the proper gapps file for the rom second _before_ booting. The gapps file you need is "gapps-hdpi-20101114-signed.zip" also in my collection.
good luck
Click to expand...
Click to collapse
One thing though. I haven't done this before. Any link to a step by step.
This is the only one I have found so far:
First time flashing CM 6.1 to your Droid (or coming from another ROM)?
1. Unlock/root your device and install Clockwork Recovery via ROM Manager (Don't see a ROM manager)
2. Do a Nandroid backup! (Not sure how to do this. Do I download an app for that?)
3. Update your radio if necessary (I am guessing this is a Euro term)
4. WIPE (Again no idea where to start)
5. Install the ROM ( I am sure by the time I get here I will be able to do this)
5. Optionally install the Google Addon
A friend suggested these apps:
download rom manager and clockwork recovery and nandroid.
I didn't find clockwork recovery but found another.
I just don't want to brick. I use this for my work phone. I have other options for a phone if all goes wrong but I just want to find as much info as possible before I commit.
SO many files on that page I don't know were to start???
thebigred67 said:
One thing though. I haven't done this before. Any link to a step by step.
Click to expand...
Click to collapse
Ahhh, I see, so you haven't even rooted your phone yet? If that's the case then I'm going to have to just refer you to some other threads/guides because you have a lot of reading to do.
I have a quite a few on my site, when in my folder, just go to parent directory a couple of times and then you will see the link for my Motorola A855 info.
Here's some more:
http://www.droidforums.net/forum/droid-labs/74028-root-droid-1-regardless-os-version.html#post766732
http://androidforums.com/droid-all-...oid-without-rsd-lite-up-including-frg83d.html
You can also google "SuperOneClick" and find info about that. PLEASE be careful and read all the info carefully before you proceed. Also, there are a boat load of video guides on Youtube, but most all of them are out-fo-date and will soft-brick your phone.
good luck
Go read all that stuff above, but also go to the cyanogenmod website and read the wiki for flashing droid 1.
Good luck!
-CM7 on DInc2
teddyearp said:
Ahhh, I see, so you haven't even rooted your phone yet? If that's the case then I'm going to have to just refer you to some other threads/guides because you have a lot of reading to do.
I have a quite a few on my site, when in my folder, just go to parent directory a couple of times and then you will see the link for my Motorola A855 info.
Here's some more:
You can also google "SuperOneClick" and find info about that. PLEASE be careful and read all the info carefully before you proceed. Also, there are a boat load of video guides on Youtube, but most all of them are out-fo-date and will soft-brick your phone.
good luck
Click to expand...
Click to collapse
I have rooted. I just haven't had the courage to do the cran install.
Hello all. I just got this Motorola a855. I rooted with universal androot. (Wow easiest root ever and its always easy!) Need custom recovery and whatnot. Can somebody send a link? Ron manager doesn't work. I'm not even sure what this phone is other than an old azz a855. Its all I have right now. Any help is appreciated. I don't need much instructions just some files. Thanks for the time!
Sent from my Droid using xda premium
I se cmw should work bu
t I can't find on market (premium foud tho) an got from internet and "problem parsing the package. I tried he bootstrap recovery and spent my $3 there. I really wanna try some custom stuff on this as thsvis a bleak device as it is. It's all rooted and ready.
Sent from my Droid using xda premium
Nvm. Did it with version 2.57. Something. Works better than I thought it would. Ics almost works on this pos. Damn what the hell is a kdz anyway!!!
Sent from my Droid using xda premium
First off, I wanna apologize if the has been discussed.
I see a lot of you broke your device by trying some form of method to fix the device in any fancy way.
I had a friend brick by trying the Cyanoboot method.
First off, assuming you have already got CWM installed via the tutorial that's been posted already.
Secondly, make sure you have some form of way to side load apps onto the device. Be it Dropbox, Google Drive, or maybe your using an ADB method.
Lastly, I have found this to be the easiest way.
So, let's begin. Please make sure you have a way of grabbing ROM Manager, back it up, download an .apk from a Google search or just port it from one device to another via an app.
Once you've found your method of getting the side loaded .apk let's make sure it's installed, any newer version will work(Older versions have been reported of not installing and allowing a proper clean reboot). So let's make sure it's a newer updated version, secondly test it and make sure the version you're using will reboot the device properly without issue. Working? Good.
Now let's use our nifty tool as soon as you have CWM installed, you should get a proper reboot!
This is good.
As a side note, I've had mine give issue and make me wait a few for a full reboot into CWM.
Now you're done!
Flashing ROMs.
It's just as easy as you'd think it'd be as long as you've got a properly packed ROM onto your device.
Note: If you're looking for a tut on porting the ROM, please check the Dev forum as there is a tut posted that is clean and simple using ADB.
Also, there are some that say you can using a cloud storage method.(Try it at your own risk!)
Once you've got your ROM onto Ouya you should check with an explorer to confirm that it was saved onto the device.(I have an issue of downloading things of the Internet with Ouya and them not showing up).
Now, using the method I first mentioned to get into CWM, do so.
You should see an option to search through your internal SD, this would be the next step as we can't/don't have any form of using an external SD, that is if you could connect a flash drive to the back and use it, though I can't confirm it would work.
Lastly, once you've scanned the internal SD and found your ROM, flash it. Sometimes this could take a bit, being my case it took 10m to install Ouya Plus.
If any issues occur, feel free to post and I shall try my best to answer anything!
Ouya-XD said:
First off, I wanna apologize if the has been discussed.
I see a lot of you broke your device by trying some form of method to fix the device in any fancy way.
I had a friend brick by trying the Cyanoboot method.
First off, assuming you have already got CWM installed via the tutorial that's been posted already.
Secondly, make sure you have some form of way to side load apps onto the device. Be it Dropbox, Google Drive, or maybe your using an ADB method.
Lastly, I have found this to be the easiest way.
So, let's begin. Please make sure you have a way of grabbing ROM Manager, back it up, download an .apk from a Google search or just port it from one device to another via an app.
Once you've found your method of getting the side loaded .apk let's make sure it's installed, any newer version will work(Older versions have been reported of not installing and allowing a proper clean reboot). So let's make sure it's a newer updated version, secondly test it and make sure the version you're using will reboot the device properly without issue. Working? Good.
Now let's use our nifty tool as soon as you have CWM installed, you should get a proper reboot!
This is good.
As a side note, I've had mine give issue and make me wait a few for a full reboot into CWM.
Now you're done!
Flashing ROMs.
It's just as easy as you'd think it'd be as long as you've got a properly packed ROM onto your device.
Note: If you're looking for a tut on porting the ROM, please check the Dev forum as there is a tut posted that is clean and simple using ADB.
Also, there are some that say you can using a cloud storage method.(Try it at your own risk!)
Once you've got your ROM onto Ouya you should check with an explorer to confirm that it was saved onto the device.(I have an issue of downloading things of the Internet with Ouya and them not showing up).
Now, using the method I first mentioned to get into CWM, do so.
You should see an option to search through your internal SD, this would be the next step as we can't/don't have any form of using an external SD, that is if you could connect a flash drive to the back and use it, though I can't confirm it would work.
Lastly, once you've scanned the internal SD and found your ROM, flash it. Sometimes this could take a bit, being my case it took 10m to install Ouya Plus.
If any issues occur, feel free to post and I shall try my best to answer anything!
Click to expand...
Click to collapse
just as an add: my Ouya did not detect a exFAT MicroSD in a USB reader. Maybe CWM only works with some formats?
glitchhawk said:
just as an add: my Ouya did not detect a exFAT MicroSD in a USB reader. Maybe CWM only works with some formats?
Click to expand...
Click to collapse
I do believe there's been a certain format to use, though I'm unaware on how this works.
Sent from my HTC One VX using xda app-developers app
glitchhawk said:
just as an add: my Ouya did not detect a exFAT MicroSD in a USB reader. Maybe CWM only works with some formats?
Click to expand...
Click to collapse
Ouya-XD said:
I do believe there's been a certain format to use, though I'm unaware on how this works.
Sent from my HTC One VX using xda app-developers app
Click to expand...
Click to collapse
FAT32 is more or less the "golden" standard for portable devices. glitchhaw, you are aware that exFAT is one of the most laughably locked down filesystems for portable devices out there, right? If you're being official at all, you have to pay royalties to Microsoft to be able to work with exFAT, and I doubt OUYA built support in for that.
Rirere said:
FAT32 is more or less the "golden" standard for portable devices. glitchhaw, you are aware that exFAT is one of the most laughably locked down filesystems for portable devices out there, right? If you're being official at all, you have to pay royalties to Microsoft to be able to work with exFAT, and I doubt OUYA built support in for that.
Click to expand...
Click to collapse
i know that I don't like exFAT and that its annoying and glitchy sometimes with android.. but I don't like the fat32 4gb limit.
i wish CWM/TWRP worked with NTFS or EXT, at least they are more reliable.
glitchhawk said:
i know that I don't like exFAT and that its annoying and glitchy sometimes with android.. but I don't like the fat32 4gb limit.
i wish CWM/TWRP worked with NTFS or EXT, at least they are more reliable.
Click to expand...
Click to collapse
NTFS support can be added at the kernel level, but I don't know of any recoveries that support it, sadly. And that's unfortunately the nature of the beast, and probably why many recoveries will break files up into multiple archives.
Go full *nix and use ext4 like a man... Unless you're a woman, then use it like a woman.
Sent from my SAMSUNG-SGH-I317 using xda premium
I am unable to get the unit to respond to Rom managers attempt at rebooting into recovery, I'll give the command via the app and it will just continue sitting there at the menu. CWM was successfully installed and I made a backup. I downloaded the app to my phone and then TB'd it and sent it to my device. did I miss something?
B4 I updated I needed SU to make the reeboot. Feature work.
Sent from my Amazon Kindle Fire using xda app-developers app
that was my thought, however I just reran the .bat for cwm and flashed that way.
Kickbut101 said:
I am unable to get the unit to respond to Rom managers attempt at rebooting into recovery, I'll give the command via the app and it will just continue sitting there at the menu. CWM was successfully installed and I made a backup. I downloaded the app to my phone and then TB'd it and sent it to my device. did I miss something?
Click to expand...
Click to collapse
I'd assume if it's not working that way then to try the ADB method instead, again, please report all issues to me.
Do you have CWM installed, on a final note?
People cry a out signatures, there's no need for one! I love my community and will stand up for it!
App: Quick Boot . reboot into fast boot, recovery, or shut down the console.
Sent from my SGH-M919G using xda app-developers app
Ouya-XD said:
First off, I wanna apologize if the has been discussed.
I see a lot of you broke your device by trying some form of method to fix the device in any fancy way.
I had a friend brick by trying the Cyanoboot method.
First off, assuming you have already got CWM installed via the tutorial that's been posted already.
Secondly, make sure you have some form of way to side load apps onto the device. Be it Dropbox, Google Drive, or maybe your using an ADB method.
Lastly, I have found this to be the easiest way.
So, let's begin. Please make sure you have a way of grabbing ROM Manager, back it up, download an .apk from a Google search or just port it from one device to another via an app.
Once you've found your method of getting the side loaded .apk let's make sure it's installed, any newer version will work(Older versions have been reported of not installing and allowing a proper clean reboot). So let's make sure it's a newer updated version, secondly test it and make sure the version you're using will reboot the device properly without issue. Working? Good.
Now let's use our nifty tool as soon as you have CWM installed, you should get a proper reboot!
This is good.
As a side note, I've had mine give issue and make me wait a few for a full reboot into CWM.
Now you're done!
Flashing ROMs.
It's just as easy as you'd think it'd be as long as you've got a properly packed ROM onto your device.
Note: If you're looking for a tut on porting the ROM, please check the Dev forum as there is a tut posted that is clean and simple using ADB.
Also, there are some that say you can using a cloud storage method.(Try it at your own risk!)
Once you've got your ROM onto Ouya you should check with an explorer to confirm that it was saved onto the device.(I have an issue of downloading things of the Internet with Ouya and them not showing up).
Now, using the method I first mentioned to get into CWM, do so.
You should see an option to search through your internal SD, this would be the next step as we can't/don't have any form of using an external SD, that is if you could connect a flash drive to the back and use it, though I can't confirm it would work.
Lastly, once you've scanned the internal SD and found your ROM, flash it. Sometimes this could take a bit, being my case it took 10m to install Ouya Plus.
If any issues occur, feel free to post and I shall try my best to answer anything!
If this was useful to you, I can only ask of a favor!
Check out my YouTube channel!
http://WWW.YouTube.com/user/TheDarkRosarySubscribe if you will! I will be covering everything Ouya and doing news soon!
Click to expand...
Click to collapse
I have to say this is probably the worst how to/tutorial I have seen on XDA.
If you're intent is to help users inexperienced with CWM, then you need to write clearly defined steps. The whole thing is vague. You don't give links to a single file or other tutorial, a how to shouldn't keep telling people to do a Google search for things. On four steps you make people search for files or another how-to.
What is the new version of Rom manager? How do you make sure it will reboot the device properly? Be specific.
You say flashing Roms is easy as long as you have a properly packed Rom. How does one go about checking that? How do you flash the Rom?
This is what a how-to is supposed to include. This is equivalent to just telling people GIYF and RTM.
Sent from my SCH-I535 using Tapatalk 4 Beta
TadeoNYC said:
I have to say this is probably the worst how to/tutorial I have seen on XDA.
If you're intent is to help users inexperienced with CWM, then you need to write clearly defined steps. The whole thing is vague. You don't give links to a single file or other tutorial, a how to shouldn't keep telling people to do a Google search for things. On four steps you make people search for files or another how-to.
What is the new version of Rom manager? How do you make sure it will reboot the device properly? Be specific.
You say flashing Roms is easy as long as you have a properly packed Rom. How does one go about checking that? How do you flash the Rom?
This is what a how-to is supposed to include. This is equivalent to just telling people GIYF and RTM.
Sent from my SCH-I535 using Tapatalk 4 Beta
Click to expand...
Click to collapse
There's no need to bash peoples thread first of all.
And secondly, you'll be reported for this.
As of how to to do this, I can't always "be specific" like you want when I post a good amount of this from my phone, so do be prepared for a tut that's not fully helpful.
Lastly, I HIGHLY doubt that you've read every tut on here, and trust me, I've seen so much worse that go down to the nick of; "If you wipe and install first, this version will fully brick the device, this version will half brick it".
So explain to me, since I've made ROM packages, I've had more tuts than just this, what do you wanna see more in a tutorial from me? Tell me and I'll try my best to help.
Don't go barging in with the intent of anger in mind and begin bashing me to the fullest.
Most people PM me and I give them what they need if they can't find it, as for you? Nuh uh, after this, NO is my final answer.
Sent from my HTC One VX using xda app-developers app
Oscar_david said:
App: Quick Boot . reboot into fast boot, recovery, or shut down the console.
Sent from my SGH-M919G using xda app-developers app
Click to expand...
Click to collapse
Thanks man, I'll make sure to add it to the OP.
Sent from my HTC One VX using xda app-developers app
Ouya-XD said:
There's no need to bash peoples thread first of all.
And secondly, you'll be reported for this.
As of how to to do this, I can't always "be specific" like you want when I post a good amount of this from my phone, so do be prepared for a tut that's not fully helpful.
Lastly, I HIGHLY doubt that you've read every tut on here, and trust me, I've seen so much worse that go down to the nick of; "If you wipe and install first, this version will fully brick the device, this version will half brick it".
So explain to me, since I've made ROM packages, I've had more tuts than just this, what do you wanna see more in a tutorial from me? Tell me and I'll try my best to help.
Don't go barging in with the intent of anger in mind and begin bashing me to the fullest.
Most people PM me and I give them what they need if they can't find it, as for you? Nuh uh, after this, NO is my final answer.
Sent from my HTC One VX using xda app-developers app
Click to expand...
Click to collapse
You reported me for what? That your feelings are hurt?
Ostensibly you created this tutorial to prevent people from bricking their OUYAs. That is why I was expecting a detailed walkthrough and was very disappointed. You created a tutorial on your phone that is lacking vital info that I have already detailed. I did not bash you to the fullest. You admit that your tut is not fully helpful, and I've seen other comments on another tut of yours that were a great deal harsher than mine about your motivation to post a poorly written tut.
I apologize for the severity of my opening line. I was and am annoyed that the "how-to" does not provide any info vital to users so that they don't brick their OUYA. Every time they are sent elsewhere for a file or info there is a risk of getting bad info or a malicious or corrupt apk. I outlined a lot of the information I think should be included. If I had all the answers I'd have included those as well, but I am here because I thought I could learn something. Maybe I still will.
Edit: I see now what type of person you are and how helpful you can be. http://forum.xda-developers.com/showthread.php?p=43031832 so the next time you see me ask for help go ahead and flame me. Don't worry I have a thick skin, so I won't feel the need to cry to the mods you hypocrite.
Sent from my GT-P3113 using Tapatalk 4 Beta
TadeoNYC said:
You reported me for what? That your feelings are hurt?
Ostensibly you created this tutorial to prevent people from bricking their OUYAs. That is why I was expecting a detailed walkthrough and was very disappointed. You created a tutorial on your phone that is lacking vital info that I have already detailed. I did not bash you to the fullest. You admit that your tut is not fully helpful, and I've seen other comments on another tut of yours that were a great deal harsher than mine about your motivation to post a poorly written tut.
I apologize for the severity of my opening line. I was and am annoyed that the "how-to" does not provide any info vital to users so that they don't brick their OUYA. Every time they are sent elsewhere for a file or info there is a risk of getting bad info or a malicious or corrupt apk. I outlined a lot of the information I think should be included. If I had all the answers I'd have included those as well, but I am here because I thought I could learn something. Maybe I still will.
Edit: I see now what type of person you are and how helpful you can be. http://forum.xda-developers.com/showthread.php?p=43031832 so the next time you see me ask for help go ahead and flame me. Don't worry I have a thick skin, so I won't feel the need to cry to the mods you hypocrite.
Sent from my GT-P3113 using Tapatalk 4 Beta
Click to expand...
Click to collapse
Don't worry, this morning I was frustrated.
I'm sorry, tell me what you think I'm missing and I'll add the quote to the OP.
I plan on doing a video tut though.
Sent from my HTC One VX using xda app-developers app
worst
this is the worst tutorial I've ever read on xda. mods please take down this how to brick your ouya tutorial before people start downloading wrong files and bricking there ouya.
Okay where is your full proof method of rooting and installing cwm on the ouya?
Sent from my Vivid 4G using xda premium
Going by the threads opened/posts by this fellow, maybe a sticky to let people know who to avoid is needed.
OP, maybe your're over-enthusiastic over your new Ouya, but XDA prides itself on people who actually KNOW what they're doing to help, not rambling nonsense.