Database Develop

[HELP] 3-button combo deleted?

Hi
I was trying to flash another ROM on my SGS, while having some bugs on CM7.
I formatted system, cahce and data, and did wipe data/factory reset + wipe cache.
I kept getting an error on flashing the new ROM, and accidently hit the "reboot system" while navigating around in CWM3.0.0.5. Now I can't get back to CWM with 3-button combo and got no ROM on my phone?
what to do? Wierd enough I can get into download mode
thanks in advance
PS: I normally use 3 button combo to get into CWM, and did this prior this episode

just flash via odin, with 3 files and re-partition.
that should work.

derrzredeem said:
just flash via odin, with 3 files and re-partition.
that should work.
Click to expand...
Click to collapse
I'm not so farmiliar with Odin yet... tried it a couple of times, sticking strictly to a guide, that I cant find right now :S
Could you give me a quick tutorial in what to combinate .e.g.?
PIT? PDA? PHONE or CSC? And what is what?
I know I used to flash a radio with the PDA function...
thanks

you should flash a low level package means a 3 files PDA, MODEM and CSC.
i.e XXJPU which contains XXJPU_modem, OXAJPU_CSC, and XXJPU_Rev3_PDA. Now you should put the files according to the names (like PDA in PDA, Modem in Modem and so on). I usually use 512pit for re-partition.
You should not put modem in pda when flashing using odin, like i said before "put the files according to the names"
ps. Do not tick any other option except repartition, (F. Reset Time, and Auto-reboot) when going back to samsung ROM from CM7
Good Luck

derrzredeem said:
you should flash a low level package means a 3 files PDA, MODEM and CSC.
i.e XXJPU which contains XXJPU_modem, OXAJPU_CSC, and XXJPU_Rev3_PDA. Now you should put the files according to the names (like PDA in PDA, Modem in Modem and so on). I usually use 512pit for re-partition.
You should not put modem in pda when flashing using odin, like i said before "put the files according to the names"
ps. Do not tick any other option except repartition, (F. Reset Time, and Auto-reboot) when going back to samsung ROM from CM7
Good Luck
Click to expand...
Click to collapse
Thanks a lot. You just managed to answer my next question at the same time as I was about to put it out (regarding check marks F. Reset Time, and Auto-reboot)... looks like it is going through now... The blue line is increasing anyway under the litthe android builder
thank you so very much
EDIT: God dang it Phone bootet up once again in original rooted firmware anf 3e recovery is back

Hmm... seems I was a bit to fast on the keyboard anyway
Followed "How to: flash firmware and kernels" from post #2 in this thread
http://forum.xda-developers.com/showthread.php?t=723596
I found a 512 pit from the link, where I also downloaded Odin. I chose the I9000XWJS3.7z from original firmware package (from the link), which included a .tar file, that I chose as PDA.
The phone boots up now, but when as it is about to show android UI, it starts to vibrate and the screen turns black, and menu button + back button light up continously.
I can get into 3e recovery know though, but is there a way to flash clockworkmod or another custom recovery via odin og 3e recovery? or could I try another combination of pit and PDA file ind Odin?
thanks again
Odin log:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> modem.bin
<ID:0/004> param.lfs
<ID:0/004> zImage
<ID:0/004> cache.rfs
<ID:0/004> factoryfs.rfs
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!

You're in a bootloop. Try wipe cache partition and do a factory reset from recovery and then reboot.
If that doesn't work try a different firmware. A LOW LEVEL PACKAGE one, JPU for example.
Afaik, JS3 only had one file (and the new JS3 is using 803pit file, tho it comes with 3 files; for me 512 always gave the best result).
Edit : You need to use a correct pit file when flashing a firmware.
~drz

derrzredeem said:
You're in a bootloop. Try wipe cache partition and do a factory reset from recovery and then reboot.
If that doesn't work try a different firmware. A LOW LEVEL PACKAGE one, JPU for example.
Afaik, JS3 only had one file (and the new JS3 is using 803pit file, tho it comes with 3 files; for me 512 always gave the best result).
~drz
Click to expand...
Click to collapse
Just to make sure I got the last part right. 803pit is for JS3? but I can use 512pit instead?
where do I get 803pit? do you have a link?
Im downloading JPY and will test it, if 803pit og wipe doesn't work.
thanks for the response

larsn84 said:
Just to make sure I got the last part right. 803pit is for JS3? but I can use 512pit instead?
where do I get 803pit? do you have a link?
Im downloading JPY and will test it, if 803pit og wipe doesn't work.
thanks for the response
Click to expand...
Click to collapse
God, you need to learn to listen/read. Use JPU, JPY is a single file.
Ps. Good luck though
~drz

Okay, I thought the name JPU/JPY determined which area it is fore?
Im downloading from here
https://www.wuala.com/Samsung Galaxy S/Firewares , Updates and Odin/?key=AfzUZSU4SpKU
but I cant seem to find JPU...
thanks for your help. Im a bit noobish regarding samsung... Its buy far not the same as HTC hehe
EDIT: Can't I just flash an original firmware with Odin, and it such case? Where do I find it. tried JPY, JS3 from above link, and get bootloops no matter what. Those files are downloaded from the sticky guide in general section, and I followed the guide. If I need to use JPU, where do I download it? all 3 files?
Right now, the phone just vibrates in intervals, but contiounsly, with back button and menu button light on

Yes, every firmware is for different region. But you need to get your phone to work first, right?
After that you can flash any firmware you want
You can download JPU from http://samfirmware.com or find a thread by BogdanSNB in general section.
Btw, Gingerbread is out
~drz

SOLVED
Finally got it to work with XJWM9 as PDA, XEEJM1 as CSC, XXJM4 as PHONE and 512pit file.

Have i bricked my phone?

I followed these instructions to root my new galaxy s, after following them and getting to stage where odin 3 v1.85 reboots my phone my dog pulled the usb cord out of the computer and now it seems to have stalled the phone at the samsung s screen, can anyone help?
http://forum.xda-developers.com/showthread.php?t=1056334
phone is only 3 days old so really keen to fix.

Can you get into download mode?
Sent from gt i9000 insanity 8.5/fugumod

yes can access d/l mode

<ID:0/023> Added!!
<ID:0/023> Odin v.3 engine (ID:23)..
<ID:0/023> File analysis..
<ID:0/023> SetupConnection..
<ID:0/023> Initialzation..
<ID:0/023> Get PIT for mapping..
<ID:0/023> Firmware update start..
<ID:0/023> zImage
<ID:0/023> NAND Write Start!!
<ID:0/023> RQT_CLOSE !!
<ID:0/023> RES OK !!
<ID:0/023> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/023> Removed!!
Odin log.

If you have a Samsung Galaxy S...
Then why in the world are you following the rooting procedure of the Samsung Galaxy S 2?
You will have to flash your phone with a firmware package now.

Try re running the process minus dog and see what happens, can take a while to reboot be patient
Sent from gt i9000 insanity 8.5/fugumod

electrotune1200 said:
If you have a Samsung Galaxy S...
Then why in the world are you following the rooting procedure of the Samsung Galaxy S 2?
You will have to flash your phone with a firmware package now.
Click to expand...
Click to collapse
Yep that could explain it, fail on my behalf for not reading properly.

Cancel my last...wrong root muppet I didnt check that link, makes me muppet too!
Sent from gt i9000 insanity 8.5/fugumod

For your sake....
Please, pay close attention to what you are flashing. You are lucky this time.
If you are unsure of what to flash, or what you are flashing, don't be affraid to ask.

ok so can someone give me a link for the correct process, also Kies wont connect to my device at the moment.

What region are you in?
Do you want 2.3.3?
Or 2.2.1?
Of course Kies won't connect, you're lucky the phone is turning on.
Download this too. Odin v1.82
http://www.megaupload.com/?d=Y7QPNEUZ

Im in Australia, Perth to be exact, and im keen to run 2.3.3

Alright sweet...
http://www.multiupload.com/E4EZ90ID7Y
2.3.3 Gingerbread, latest UK official release.
Are you with Optus?

Im with Telstra. D/l link now have ivivd d/l manger?

Ok....
I was just asking if you were with Optus because I have an Optus csc you could flash, but no worries.
After the flash, you will need to edit your apn settings manually to get a data connection. We'll worry about that later.
In the Odin package I had you download, is there a 512 pit file in the folder?

Did you click on the blue "direct download" button?

s1_odin_20100512 is the file

re d/l the second link

have phone in d/l mode

Ok...
Put pooch in another room. Lock the door if you have to.
Make sure phone is completely charged.
Open up Odin.
Select the pit tab. Go to the root of the Odin folder and select the 512 pit file. (The file you posted the details of)
Now select PDA tab in Odin, and navigate to the JVO ROM folder you downloaded. Select the PDA file.
Same for the PHONE, and CSC tab. Make sure you put the right files in the right slots.
Make sure re-partition in Odin is ticked.
Connect Phone to PC, when Odin recognises the phone a yellow box will appear. Press start.

Galaxy S I9000M - keep rebooting (software brick)

Hi,
I managed to brick my Samsung Galaxy S I9000M.
Was locked on Virgin network (Canada) and I was trying to root the phone and then unlock it.
But something didn;t work properly (or I made a mistake) and now the phone keeps rebooting. I can go into Download mode but nothing more.
This is what I did:
1) I installed Odin 1.85
2) I started ODIN as admin, I pressed on PDA and then I selected a zip folder called
"CF-Root-XX_OXA_JVO-v3.2-CWM3RFS"
3) This is what ODIN was showing:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003> NAND Write Start!!
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
5) So after waiting 5-6 minutes (in this time the phone was rebooting up to the Samsung logo) I turned off the phone and I have tried to start the device. But is not starting anymore, it keeps rebooing.
Now I don't know what to do to fix it.I know that I made a big mistake, I was not supposed to do something without knowing what I'm doing...But now it's too late, I have to fix it.
Note: The phone was running Android 2.3 (Gingerbread)

if its in boot loop then look like it's only softwoer brick.
so if you can get in to download mode by 3 bouten combination greate you can try to reflash (I will try all so to redownloading the files)
if not than you must find a JIG or some one with a JIG to get in to download mode and reflash.

The version of CF-ROOT you selected is not compatible with the version of GB (UGKG3?) that was on your phone.
If your phone had UGKG3 installed, there are very few rooted kernels available for it.

Black Rose said:
The version of CF-ROOT you selected is not compatible with the version of GB (UGKG3?) that was on your phone.
If your phone had UGKG3 installed, there are very few rooted kernels available for it.
Click to expand...
Click to collapse
Is the latest speed mod kernel compatible?
Sent from my GT-I9000 using xda premium

Yes, I can go into download mode.
How can I reflash the phone ? Which kernel should I use ?
Sorry but I'm new in this.
If you give me some links that will be great.
I don't want to aggravate the situation .

If the OP has/had UGKG3 installed, I have found that to be the oddest ROM I have used to date on my phone.
It does a lot of things differently.
I made another post on here where I attached a basic rooted kernel for the UGKG3 ROM. Let me go find it and link to it.
Again, this is assuming it was UGKG3. Ma Bell has only released one GB ROM for the GT-i9000m, so I think it's a safe bet that's what the OP was running on his Virgin branded phone.
EDIT: Here it is: http://forum.xda-developers.com/showpost.php?p=21655532&postcount=492
This will give you a basic rooted kernel, no CWM or anything else, just root.
You'll also need to download Superuser from the Market.

Thank you.
Now how should I install that kernel?
I suppose that after I reflash the phone it will start normally and then I can go to the Android market and install Superuser from there?
Is there a link with instructions (Step by Step guide)?
Sorry,but I dont have too much experience with this.
Thanks a lot!

I found this in the General thread, it has links and step-by-step instructions:
http://forum.xda-developers.com/showthread.php?t=1379650
Hope it helps

IntelQC said:
Thank you.
Now how should I install that kernel?
I suppose that after I reflash the phone it will start normally and then I can go to the Android market and install Superuser from there?
Is there a link with instructions (Step by Step guide)?
Sorry,but I dont have too much experience with this.
Thanks a lot!
Click to expand...
Click to collapse
Open Odin, select the zImage.tar file as PDA. DO NOT CHANGE ANY OTHER SETTINGS.
Connect your phone to your computer and wait for the ID:COM box to turn yellow.
Press Start.
Your phone will reboot and it should start normally.

Black Rose said:
Open Odin, select the zImage.tar file as PDA. DO NOT CHANGE ANY OTHER SETTINGS.
Connect your phone to your computer and wait for the ID:COM box to turn yellow.
Press Start.
Your phone will reboot and it should start normally.
Click to expand...
Click to collapse
Thank you very much !!!
My phone is fine now. It's rooted and I managed to unlock it using Galaxy_S Unlock + SuperBox from the market.
Thanks a lot .
This is what my phone shows now:
Firmware: 2.3.3
Baseband version: I9000UGKG3
Kernel version: [email protected]#2
Build number: GINGERBREAD.GKG3

Great, glad you got your phone working again.

Galaxy Ace S 5830M Bootloop

Hello,
I have a friend with a Non-Rooted, totally stock Galaxy Ace s5830M that's stuck on a boot loop. He was playing a game and the screen started flashing and it rebooted. It is now stuck in a boot loop.
I've been able to get in to Stock Recovery and in to Download mode without issues.
We tried to flash Clockwork Mod Recovery. It apparently succeeds , but when we reboot it does not "stick". Flash CWM,reboot and it just shows the Stock recovery menu. I found this thread, regarding this issue.. But this phone is completely stock, bought on Amazon and shipped to Venezuela. I think it was running Gingerbread.
We then tried to flash to a Stock Firmware from my country from Sammobile.com with Odin.
Once a single file recovery ( a large file with a md5.tar extension) and it fails:
<ID:0/037> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830MWHLA1_S5830MUUBLA1_S5830MWHLA1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/037> Odin v.3 engine (ID:37)..
<ID:0/037> File analysis..
<ID:0/037> SetupConnection..
<ID:0/037> Initialzation..
<ID:0/037> Get PIT for mapping..
<ID:0/037> Firmware update start..
<ID:0/037> sbl.bin
<ID:0/037> NAND Write Start!!
<ID:0/037> BcmCP.img
<ID:0/037>
<ID:0/037> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Then we tried another solution from another site, flashing a multiple file firmware (BOOT, PDA and PHONE). We get this result, apparently it is succesful:
<ID:0/037> Added!!
<ID:0/037> Odin v.3 engine (ID:37)..
<ID:0/037> File analysis..
<ID:0/037> SetupConnection..
<ID:0/037> Initialzation..
<ID:0/037> Set PIT file..
<ID:0/037> DO NOT TURN OFF TARGET!!
<ID:0/037> Get PIT for mapping..
<ID:0/037> Firmware update start..
<ID:0/037> BcmBoot.img
<ID:0/037> NAND Write Start!!
<ID:0/037> HEDGE_NVRAM8_RF_LE.bin
<ID:0/037> sysparm_dep.img
<ID:0/037> system.img
<ID:0/037> boot.img
<ID:0/037> param.lfs
<ID:0/037> sbl.bin
<ID:0/037> BcmCP.img
<ID:0/037> Transmission Complete..
<ID:0/037> Now Writing.. Please wait about 2 minutes
<ID:0/037> Receive Response form LOKE
<ID:0/037> RQT_CLOSE !!
<ID:0/037> RES OK !!
<ID:0/037> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/037> Removed!!
Click to expand...
Click to collapse
When we reboot the phone, we now get a boot screen that says the device is a S5830C instead of a S5830M. But it's still stuck on the Samsung logo at boot.
We really don't know what else to try. Any ideas? Is this phone bricked?
Thanks,
Rafael

Factory reset ur phone from recovery & wipe cache. Also, U need to place the individual firmware files at correct fields in odin (hope U did that) otherwise ur phone'll not be able to boot properly.
As far as I know there are four files (BOOT, PHONE, PDA, CSC) in full package & only one file (of extension:- tar.md5) in One Package firmware...
Sent Via XDA Premium

Galaxy_Rohit said:
Factory reset ur phone from recovery & wipe cache. Also, U need to place the individual firmware files at correct fields in odin (hope U did that) otherwise ur phone'll not be able to boot properly.
As far as I know there are four files (BOOT, PHONE, PDA, CSC) in full package & only one file (of extension:- tar.md5) in One Package firmware...
Sent Via XDA Premium
Click to expand...
Click to collapse
U managed to screw the phone ... It was as simple as as factory reset you were lucky! You could have hard bricked is ace ! Flash a proper rom to 5830 M and the enter STOCK RECOVERY! and do wipe data!
Sent from my GT-I9830 using xda premium

Yep, that's the first thing we did, we did a wipe data and wipe cache.
Here are the steps we took when flashing via Odin.
Settings we used:
Files we used to flash:

marcano said:
Yep, that's the first thing we did, we did a wipe data and wipe cache.
Here are the steps we took when flashing via Odin.
Settings we used:
Files we used to flash:
Click to expand...
Click to collapse
U used odin for 5830i ...
Sent from my GT-I9830 using xda premium

You need to do a hard reset after flashing the stock rom.
Enviado desde mi LG-P350 usando Tapatalk 2

SnowPluralism said:
U used odin for 5830i ...
Sent from my GT-I9830 using xda premium
Click to expand...
Click to collapse
The S5830i, S5830C, S5830M and S5839i are the same aka cooperve.
The only difference is the region, this version of Odin works with S5830M too!
Anyway, this rom you flashed is from Brazil, and works with your phone too. Try a wipe data/factory reset on recovery, this maybe works.
You should have a look at S5830i Development and S5830i General, there you will find more answers about your phone.

Stock ROM for SGA 5830M
marcano said:
Hello,
I have a friend with a Non-Rooted, totally stock Galaxy Ace s5830M that's stuck on a boot loop. He was playing a game and the screen started flashing and it rebooted. It is now stuck in a boot loop.
I've been able to get in to Stock Recovery and in to Download mode without issues.
We tried to flash Clockwork Mod Recovery. It apparently succeeds , but when we reboot it does not "stick". Flash CWM,reboot and it just shows the Stock recovery menu. I found this thread, regarding this issue.. But this phone is completely stock, bought on Amazon and shipped to Venezuela. I think it was running Gingerbread.
We then tried to flash to a Stock Firmware from my country from Sammobile.com with Odin.
Once a single file recovery ( a large file with a md5.tar extension) and it fails:
Then we tried another solution from another site, flashing a multiple file firmware (BOOT, PDA and PHONE). We get this result, apparently it is succesful:
When we reboot the phone, we now get a boot screen that says the device is a S5830C instead of a S5830M. But it's still stuck on the Samsung logo at boot.
We really don't know what else to try. Any ideas? Is this phone bricked?
Thanks,
Rafael
Click to expand...
Click to collapse
Hi Rafael. OK, I have made a detailed how to in Taringa that specifies the way to install a Stock ROM for SGA GT-S5830M. Just search in google "tutorial flashear samsung galaxy ace 5830m con odin - Taringa!" (without quotation marks) and enter the first result, it would redirect you to my post, check that the name of the creator is "jhonaff", if so, just download the files from there, and flash them via Odin 1.85 or 1.87. In the post there is a link to download the version 1.85, this version of Odin is the one that works perfectly with this device. Following that steps I gave life again to my SGA 5830M.
After you download, unzip the files in the S5830M.rar archive, you will get three .tar.md5 files; now put the files in the following order in Odin:
BOOTLOADER -> leave this section empty.
PDA -> select the PDA file.
PHONE -> select the MODEM file.
CSC -> select the CSC file.
Now click Start button and wait for the process to finish; at the end of the process the phone will reboot in recovery automatically and it will run a script, don't unplug it, and don't do anything yet. The phone will reboot once more and now it will pass the Samsung logo and will show you the Samsung bootanimation. Now you can unplug it and wait, the first boot may take 1 or 2 minutes and you will get your phone alive again.
PD: I can't give you a link to my post cause I'm new in this site and I don't have 2 posts here, so I can't post links in my replies.
PD2: My post in Taringa is in Spanish, I think it is understandable, but if not, use a traductor, after all you just want to download the correct files.
I hope this can help you. I speak spanish and has been years from the last time I spoke in English, so forgive me if something is wrote incorrectly.

Thank you jhonaff2
jhonaff2 said:
Hi Rafael. OK, I have made a detailed how to in Taringa that specifies the way to install a Stock ROM for SGA GT-S5830M. Just search in google "tutorial flashear samsung galaxy ace 5830m con odin - Taringa!" (without quotation marks) and enter the first result, it would redirect you to my post, check that the name of the creator is "jhonaff", if so, just download the files from there, and flash them via Odin 1.85 or 1.87. In the post there is a link to download the version 1.85, this version of Odin is the one that works perfectly with this device. Following that steps I gave life again to my SGA 5830M.
After you download, unzip the files in the S5830M.rar archive, you will get three .tar.md5 files; now put the files in the following order in Odin:
BOOTLOADER -> leave this section empty.
PDA -> select the PDA file.
PHONE -> select the MODEM file.
CSC -> select the CSC file.
Now click Start button and wait for the process to finish; at the end of the process the phone will reboot in recovery automatically and it will run a script, don't unplug it, and don't do anything yet. The phone will reboot once more and now it will pass the Samsung logo and will show you the Samsung bootanimation. Now you can unplug it and wait, the first boot may take 1 or 2 minutes and you will get your phone alive again.
PD: I can't give you a link to my post cause I'm new in this site and I don't have 2 posts here, so I can't post links in my replies.
PD2: My post in Taringa is in Spanish, I think it is understandable, but if not, use a traductor, after all you just want to download the correct files.
I hope this can help you. I speak spanish and has been years from the last time I spoke in English, so forgive me if something is wrote incorrectly.
Click to expand...
Click to collapse
Thank you very much jhonaff2, you solved my problem after some days
I know it is not related to this post, but do you know how can I enable my 3G radio in US T-Mobile? I can only get their 2G services

geniusbabak said:
Thank you very much jhonaff2, you solved my problem after some days
I know it is not related to this post, but do you know how can I enable my 3G radio in US T-Mobile? I can only get their 2G services
Click to expand...
Click to collapse
we have same problem in 3g. i can only get 2g services

[Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode screen

[Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode screen
Hi,
I was trying to install new ROM through Odin software. I tried with Odin3 one click downloader. I also tried using KI2 with Boog's Kernel odin software. but both are failing. Shows FAIL with following output -
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
Another problem is that for my Samsung Captivate mobile... Download mode screen stopped coming ( I think it happened when by mistake I updated mobile's bootloader with some Corn s/w bootloader by selecting the file in Bootloader field in Odin. It created a big problem for me. I couldn't go in to download mode after this.
So finally I purchased USB jig to enable Download mode (last option to make mobile in download mode).
Even though I can update the firmware using Jig. But still download mode screen is not coming.But when I connect mobile to computer with usb cable, after using USB jig, I could see that odin shows "ADDED" with yellow box showing some port no. Above output comes when i continue with installing tar/md5 file of ROM with Odin. but it fails. So i am unable to use my mobile... .
It worked when I updated ROM with following package - GT_I9000_ZSJPK_ZSJPG_OZSJPG. It contains PDA, PHONE and CSC files.
First I did partition with file s1 odin 20100512.pit and after that I selected these three files in corresponding fields in Odin software and clicked on start button. It worked and i could see FROYO installed in my captivate phone. But this ROM update is for I9000 mobile. so all functionality is not working properly. what i mean to say here that I can update mobile with I9000 ROM. but not with captivate ROM.
My mobile's situation is that it has no software installed. Just as a hardware. No Bootloader, Nothing. Even AT & T screen doesnt come when I start my mobile. It is totally dead.
Can anybody please help me ? how can I resolve this problem. I searched all the thread in forum. But it is not helping me to resolve my problem. .
Issues are -
AT & T screen is not coming when i start the phone.
Download mode screen is not coming when i start the phone.
Just Assume that I have captivate phone without partition, without bootloader ...
Can anybody please help ?

vishu_10d said:
Hi,
I was trying to install new ROM through Odin software. I tried with Odin3 one click downloader. I also tried using KI2 with Boog's Kernel odin software. but both are failing. Shows FAIL with following output -
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
Another problem is that for my Samsung Captivate mobile... Download mode screen stopped coming ( I think it happened when by mistake I updated mobile's bootloader with some Corn s/w bootloader by selecting the file in Bootloader field in Odin s/w. It created a big problem for me. I couldnt go in to downlaod mode after this.
So finally I purchased USB jig to enabled Download mode (last option to make mobile in downlaod mode).
Even though I can update the firmware using Jig. But still download mode screen is not coming.But when I connect mobile to computer with usb cable, after using USB jig, I could see that odin shows "ADDED" with yellow box with some port number. Above output is comes when i continue installing tar/md5 file of ROM with Odin. but it fails. So i am unable to use my mobile... .
It worked when I updated ROM with following package - GT_I9000_ZSJPK_ZSJPG_OZSJPG. It contains PDA, PHONE and CSC files.
First I did partition with file s1 odin 20100512.pit and after that I selected these three files in corresponding fields in Odin software and clicked on start button. It worked and i could see FROYO installed in my captivate phone. But this ROM update is for I9000 mobile. so all functionality is not working properly. what i mean to say here that I can update mobile with I9000 ROM. but not with captivate ROM.
My mobile's situation is that it has no software installed. Just as a hardware. No Bootloader, Nothing. Even AT & T screen doesnt come when I start my mobile. It is totally dead.
Can anybody please help me ? how can I resolve this problem. I searched all the thread in forum. But it is not helping me to resolve my problem. .
Issues are -
AT & T screen is not coming when i start the phone.
Download mode screen is not coming when i start the phone.
Just Assume that I have captivate phone without partition, without bootloader ...
Can anybody please help ?
Click to expand...
Click to collapse
Here's what you need: http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Grab Odin KK4 with bootloaders from that thread. That should get your phone back up. If you wanna get farther and flash a custom ROM, follow http://forum.xda-developers.com/showthread.php?t=1350266

BWolf56 said:
Here's what you need: http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Grab Odin KK4 with bootloaders from that thread. That should get your phone back up. If you wanna get farther and flash a custom ROM, follow http://forum.xda-developers.com/showthread.php?t=1350266
Click to expand...
Click to collapse
Thanks for the reply...
I tried with Odin one click downloader also... but it is failing... attaching the image...

Re: [Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode scr
Try a different micro usb/usb cable. And also a different usb port if the different cable doesn't work.
And if that fails...some Captivates don't like One Clicks, so see my post here...http://forum.xda-developers.com/showthread.php?p=30840818
Then use the [Utility]KK4 Easy Root by Red_81 http://forum.xda-developers.com/showthread.php?p=26710533 to get Root and KK4 Corn Kernel that has CWM Recovery...if u want.
Another helpful sticky thread...http://forum.xda-developers.com/showthread.php?p=33227541
Sent from my SAMSUNG-SGH-I747 using xda premium

4-2ndtwin said:
Try a different micro usb/usb cable. And also a different usb port if the different cable doesn't work.
And if that fails...some Captivates don't like One Clicks, so see my post here...http://forum.xda-developers.com/showthread.php?p=30840818
Then use the [Utility]KK4 Easy Root by Red_81 http://forum.xda-developers.com/showthread.php?p=26710533 to get Root and KK4 Corn Kernel that has CWM Recovery...if u want.
Another helpful sticky thread...http://forum.xda-developers.com/showthread.php?p=33227541
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Hi,
I followed the steps written in the forum above. But that is not working my case. I tried the steps in different computer with diff OS installed. but still same problem.
Is there any way to get PHONE, PDA, CSC file separately for i897 ? I could install I9000 in my samsung captivate mobile which had these files. So just thought, if i can get these files for i897, probably it should work?
Any Idea where i can get these files?

Re: [Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode scr
^
Here ya go...http://forum.xda-developers.com/showthread.php?p=19587108
Sent from my SAMSUNG-SGH-I747 using xda premium

4-2ndtwin said:
^
Here ya go...http://forum.xda-developers.com/showthread.php?p=19587108
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Hi,
Still my problem is same. I went through the link. but that is also not helping.
In my phone, I cant see download screen, even though if i use USB jig.
When I run Odin s/w, I can see in odin as port "Added" when Connect my mobile with computer using usb port.
Usually Odin show port added when u are in download mode. But here in my case, when i first USB jig and then connect to computer, download mode screen message and image doesnt come. it shows nothing(like no display). But I can see , Odin shows port Added. and I could update kernel, do partitions etc. But when I select Image file as PDA. and click start. It always fails.
Is it happening because i cant see download mode screen ?
1. What firmware I need to install and how which contains code for showing download screen ?
2. Or can anybody provide me all files i.e. PIT, Bootloader, PDA, Phone, CSC for odin so that i can select all files in respective fields under Odin software and start update?
Please help.
One more thing i have noticed.. here is the output of odin when i update my mobile with following files of I9000 model. while trying images for my captivate mobile, I found a zip file for model GT I9000 and package name was -GT_I9000_ZSJPK_ZSJPG_OZSJPG. It had three files as - 1. CSC_OZSJPG.tar.md5. 2. PDA_ZSJPK.tar.md5. 3. PHONE_ZSJPG.tar.md5.
I selected this files in corresponding PHONE, CSC, PDA fields in odin and it updates phone successfully with the following output -
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_ZSJPK.tar.md5 is valid.
<OSM> PHONE_ZSJPG.tar.md5 is valid.
<OSM> CSC_OZSJPG.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> param.lfs
<ID:0/017> zImage
<ID:0/017> factoryfs.rfs
<ID:0/017> dbdata.rfs
<ID:0/017> modem.bin
<ID:0/017> cache.rfs
<ID:0/017> Removed!!
<ID:0/017> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/018> Added!!
<ID:0/018> Removed!!
<ID:0/019> Added!!
But even though i can see my phone with I9000 model image installed. but most of the operations it doesnt work. might be becoz image is not fully compatible with Captivate model. so no use.

You should always be able to see the download screen no matter what fw you're on. I could see it on 2.3.5, 4.2.2, etc. Even with a jig you can't force it into download mode? Did you make it or buy it?

x0ne215 said:
You should always be able to see the download screen no matter what fw you're on. I could see it on 2.3.5, 4.2.2, etc. Even with a jig you can't force it into download mode? Did you make it or buy it?
Click to expand...
Click to collapse
I purchased a jig for samsung captivate from ebay website. when I tried with it, It doesnt show me downlaod mode screen. But it make my mobile able to connect to system. And I can see the port as added in odin. using that only I have installed android froyo of GT I9000 model in captivate mobile. I tried with all the PDA files available in forums here, but it didnt work.
Presesnt situation is, I am using captivate mobile which have android version of GT 9000 model. As I mentioned in the post.

vishu_10d said:
I purchased a jig for samsung captivate from ebay website. when I tried with it, It doesnt show me downlaod mode screen. But it make my mobile able to connect to system. And I can see the port as added in odin. using that only I have installed android froyo of GT I9000 model in captivate mobile. I tried with all the PDA files available in forums here, but it didnt work.
Presesnt situation is, I am using captivate mobile which have android version of GT 9000 model. As I mentioned in the post.
Click to expand...
Click to collapse
I'm curious do you ever see anything on your screen?
Sent from my SGH-I897 using xda app-developers app

m1batt1 said:
I'm curious do you ever see anything on your screen?
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
Yes. As i Said. I am running Android version of GT 9000 on my Samsung Captivate model and it is working fine(except some cases e.g. screen orientation while running games and some other apps, Media sound doesnt come etc).

vishu_10d said:
Yes. As i Said. I am running Android version of GT 9000 on my Samsung Captivate model and it is working fine(except some cases e.g. screen orientation while running games and some other apps, Media sound doesnt come etc).
Click to expand...
Click to collapse
I think it meant something along the lines of ''What is showing on your screen while in download mode''?

BWolf56 said:
I think it meant something along the lines of ''What is showing on your screen while in download mode''?
Click to expand...
Click to collapse
Hi,
when i usb jig and after that connect to system. I can see port Added in Odin software. which ideally happens when mobile is in downlaod mode.
but here for me display doesnt show anything on screen, screen remain blank. No android icon comes. but still I can see port added in odin and also can install files in the mobile. like pit, bootloader PDA files. etc.

I have tried my image files which is available with bootloaders in forum. But when I start. I always get following error.
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
It always fails while executing sbl.bin files. I have gone through some forum where reports similar issue of sbl.bin.
Resolution which was given is to try with " 4 part flash files" which is Boot, PDA, Modem, CSC files.
http://www.droidevelopers.com/f299/14467-sbl-bin-error.html.
But this solution is not for captivate mobile.
It would be good if someone can provide me these files instead of a single installable file.

vishu_10d said:
I have tried my image files which is available with bootloaders in forum. But when I start. I always get following error.
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
It always fails while executing sbl.bin files. I have gone through some forum where reports similar issue of sbl.bin.
Resolution which was given is to try with " 4 part flash files" which is Boot, PDA, Modem, CSC files.
http://www.droidevelopers.com/f299/14467-sbl-bin-error.html.
But this solution is not for captivate mobile.
It would be good if someone can provide me these files instead of a single installable file.
Click to expand...
Click to collapse
I believe 4-2ndtwin has the link to them in his sig.

BWolf56 said:
I believe 4-2ndtwin has the link to them in his sig.
Click to expand...
Click to collapse
So any suggestions ? what should I do now ?

vishu_10d said:
So any suggestions ? what should I do now ?
Click to expand...
Click to collapse
Search for 4-2ndtwin.. Go into his profile, then sig link and find the separated files.

vishu_10d said:
So any suggestions ? what should I do now ?
Click to expand...
Click to collapse
You need Jtag
Check my signature for more detail.

Here is the i897uckf1 gingerbread 2.3.3 files...http://forum.xda-developers.com/showthread.php?p=30840818...Post #284 in that thread.
Do not put any files in the Bootloader tab of Odin. Just PDA in pda tab, CSC in csc tab, PHONE in phone tab and also Pit file in the pit tab. Be sure to have a reliable usb/micro usb and constant power source. This firmware does contain the Bootloaders.
Sent from my SAMSUNG-SGH-I747 using xda premium

4-2ndtwin said:
Here is the i897uckf1 gingerbread 2.3.3 files...http://forum.xda-developers.com/showthread.php?p=30840818...Post #284 in that thread.
Do not put any files in the Bootloader tab of Odin. Just PDA in pda tab, CSC in csc tab, PHONE in phone tab and also Pit file in the pit tab. Be sure to have a reliable usb/micro usb and constant power source. This firmware does contain the Bootloaders.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Thanks a lot for providing me these files. This is what I wanted. I will try as you suggested and will let you know the result.
Thanks