Finally got all my parts for my car mount, and got everything put together.
I was limited with what I could do as I don't want something hanging off my windshield, and I won't put any holes in my console, etc.
The goal was to have the car still be as stock looking as possible.
So I used magic. And I think this same mount, and idea could be used pretty much universally for most cars.
I've already got a bluetooth rig setup, so it's all wireless unless I wanted to charge.
The list of supplies goes like this.
1x -Padholdr social 7" tablet mount http://padholdr.com/ipad-and-tablet-holders/
1x -4' x2" package of industrial velcro
2x - 1/2"x1/2" cylinder neodymium magnets
2x - 1"x1/2"x1/8" bar neodymium magnets
some 3m double sided trim/mounting tape.
Let's get right into the pictures.
This is what I'm working with, not quite as easy as the center consoles that have a small trim piece that pops right off around the radio.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here's the padholdr, the Nexus fits in it nicely without any modification. They also include bigger spacers, so you can take the two halves apart, and make it hold a thicker device, such as a nexus in a case.
You'll see in this picture, the bottom of the padholdr is curved. The back piece will rest on the gray ledge on my dash, the curved nature could mean it would want to rock back and forth. And even more importantly, the padholdr hits my volume knob on the radio and it just overall sits higher then I'd like.
Time to bust out the dremel. Not only will the flat edge make it sit more stable, but it will also give the clearance needed for the volume knob.
Using the router attachment, and standard bit that came with the dremel. Great success. Went through the acrylic/plexiglass like butter.
Padholdr all put back together after the cut. As you can see, the front piece will block any of this from being seen, as it still has the curve in it.
If you look back at my dash, the 1/2 x 1/2" cylinder magnets went behind the dash with the 3m mounting tape. In between the radio and the air vents, Just below center on those vertical columns. Once the dash was all back together, you can't even tell they are there. This is the stock look I was going for. Magnets don't seem to have any effect on the radio, etc.
Here is the padholdr, after applying the soft side of the velcro. To the cut I had made previously, and the back of the padholdr where it may come in contact with the dash. Then the 1x1/2x1/8" bar magnets were attached to the padholdr using the same 3m mounting tape, and then covered with the velcro as well. So they wont leave any marks from contact with the dash.
Lets see what we've got. Nice! Everything is clearing the radio, and it just barely sticks out at all. Lookin good.
Now, will this thing hold with the extra weight of the tablet?
The answer seems to be yes, yes it will!
Other angles.
Went for a cruise last night and it didn't move a hair. Used it for the first time for real this morning on the way to work, solid.
There are probably some concerns about the magnets. I had the tablet up and running, and playing a song while putting it into the padholdr. It doesnt turn the screen off, doesnt distort the speaker. I haven't found any ill effects. I even calibrated the compass with it in the padholdr and the compass was still working.
This same type of mount could be applied to virtually any vehicle.. As long as there's a trim piece around the radio that you can gain access to. Very happy with it so far.
I could probably do a video of it in action if people want it.
This morning on the way to work I was jammin out, while putting my gauges from torque up, and then when i hit traffic went to maps and figured out where the traffic jam was.. Such a badass tool to have in the car.
This is some fine crafting! Maybe I'll do something similar when I receive mine.
That Is pretty nice if I do say so myself. I plan on integrating mine into my car as my source of entertainment as well. I'm not keeping my radio though.
Question ... do u use ur fone for internet?
Sent from my PC36100 using Tapatalk 2
cybervyrus8587 said:
That Is pretty nice if I do say so myself. I plan on integrating mine into my car as my source of entertainment as well. I'm not keeping my radio though.
Question ... do u use ur fone for internet?
Sent from my PC36100 using Tapatalk 2
Click to expand...
Click to collapse
Yep. I've got an EVO LTE on sprint so I just crank the hotspot on there. I've got an ubuntu server setup at my house and I run a subsonic server off of that. So all that coupled with the subsonic app on the nexus means, instant access to 500gb of my music and movies while I'm movin down the road.
I also plan on putting a couple nfc tags in hidden locations, one to turn the hotspot on for my evo. And then basically an enter and exit for the nexus. The enter would set the screen to never turn off, and bluetooth and volume. While the exit tag would put it all back where it was.
regalpimpin said:
Yep. I've got an EVO LTE on sprint so I just crank the hotspot on there. I've got an ubuntu server setup at my house and I run a subsonic server off of that. So all that coupled with the subsonic app on the nexus means, instant access to 500gb of my music and movies while I'm movin down the road.
I also plan on putting a couple nfc tags in hidden locations, one to turn the hotspot on for my evo. And then basically an enter and exit for the nexus. The enter would set the screen to never turn off, and bluetooth and volume. While the exit tag would put it all back where it was.
Click to expand...
Click to collapse
U wouldn't happen to live in TX would u? I only ask cuz I would love to get some pointers especially with those hidden nfc chips. Also.. r u worried at all the Sprint will find out ur tethering?
Sent from my PC36100 using Tapatalk 2
That looks great! I'm going to try this with a Tab 2 7.0 in my Fusion.
Sent from my Galaxy Nexus using Tapatalk 2
I am extremely curious to know how you set up your car to do bluetooth audio.
What do you use for FM radio? Have you found a way to control it from the 7? Unfortunately I think the only solution is to use a data streaming service like tunein radio.
This is an awesome idea! I definitely need to look into something like this.. A video would be nice, if you wouldn't mind.
ifalldownalot said:
I am extremely curious to know how you set up your car to do bluetooth audio.
Click to expand...
Click to collapse
Haha I see what you mean..
Sent from my Nexus 7 using xda app-developers app
For the bluetooth audio to the stock radio.. It's a combination of things. And I'll get some pictures or video later.
First, I had an iPod2car.
Something like this, other companies make them now as well
http://www.crutchfield.com/S-pseW37dLoOC/p_541PXDP2/Peripheral-iPod2car-iPod-Adapter.html
This charges an ipod, and allows the seek on the factory radio, to actually seek on the ipod. It plugs into the factory cd changer input that was in my trunk. Didn't have a cd changer, but they run the cable on all the cars, whether they had it or not.
So on my factory radio I just have to choose the cd changer as the source, instead of fm or cd. And its a wired connection, not a transmitter= no static
i sold my iPod a long time ago though. So this cable was really of no use to me anymore.
That's when i picked up an adapter that converts the male ipod cable, to an auxillary input.
http://www.cablejive.com/products/dockBoss.html Mine had a female stereo jack on it though. Looks like they've just changed it slightly through the years.
I made this into a nice panel, so that I can still use the ipod cord, or plug the ipod cord into the panel which is in my cubby hole in the center console, in which then it acts as the universal input instead.
(this is what i may take some pictures of.)
The aux input then exits from the center console on the passenger side, right at the floor. Out of sight, out of mind.
Then I use the HTC Stereoclip to receive the bluetooth audio as I also have an evo lte.
http://shop.htcpedia.com/htc-car-stereoclip-audio-bridge-a100.html
Basically. Hop in car, turn on hotspot, turn on bluetooth adaptor. put nexus in the padholdr and put it in place, turn on bluetooth. It automatically pairs and connects to the stereoclip. Then automatically opens the car home ultra app and I'm off.
I'll make a video of how it all works.
Buick should def think about replacing that crappy stereo with a touchscreen
They have of course in the new Regals.
Unfortunately that new regal just cant put out the same kinda power to the wheels that this 14 year old with 200,000 miles can.
regalpimpin said:
They have of course in the new Regals.
Unfortunately that new regal just cant put out the same kinda power to the wheels that this 14 year old with 200,000 miles can.
Click to expand...
Click to collapse
Man I completely agree!!! Love the old regals
Sent from my Nexus 7 using Tapatalk 2
Nice setup. I also have a regal and made a phone mount a whole back. I was wondering about your input. I've been looking for something like that for years. Currently I use a fm transmitter / hands free kit, but the quality sucks. Do all regal have that input, I don't think mine does?
Sent from my Nexus 7 using xda app-developers app
Could someone explain the magnets to me? Confused, is it attached to the dash with velcro or magnets? ....or both?
Could I also ask how big the Padholdr is exactly? I especially want to know how long the entire unit is (for a Nexus 7 fit) and how thick the right and left "legs" are. (these are the parts I'll be attaching to my dash).
Thanks!
Great post! I am gonna try it
Sent from my Nexus 7 using Tapatalk 2
Nice work :good: Can you tell me what App your using as an interface as the chunky buttons look far better and easier to use than the stock media controls.
Godswrath said:
Could someone explain the magnets to me? Confused, is it attached to the dash with velcro or magnets? ....or both?
Could I also ask how big the Padholdr is exactly? I especially want to know how long the entire unit is (for a Nexus 7 fit) and how thick the right and left "legs" are. (these are the parts I'll be attaching to my dash).
Thanks!
Click to expand...
Click to collapse
It just sticks there via magnets. The velcro, is just stuck on over the magnet, so there aren't any hard surfaces to scratch the dash. It's just padding.
The back piece on the bottom of the mount that I cut rests on the ledge holding some of the weight, and the magnets then hold it firmly in place.
So there are the bar magnets on the back of the padhldr, and then I took apart the dash, and there are slightly bigger cylinder magnets on either side of the radio behind the dash trim. So if the holder isn't in use, its totally stock. I don't believe in sticking anything to the dash which is why I came up with this solution in the first place.
-As for the padholdr dimensions, I can get more detail later, but I'd say the sides are about an inch wide at the thickest section on the bottom. And again, you can use different spacers that they supply for different thicknesses of tablets, or if you had the nexus in a case like the moko slim-fit.
And an update after using this for a few months now. Always been perfect. Nexus has never budged or gone flying off on me. Still working great.
rushy75 said:
Nice work :good: Can you tell me what App your using as an interface as the chunky buttons look far better and easier to use than the stock media controls.
Click to expand...
Click to collapse
That is CarHome Ultra. and with more recent updates you can alter the appearance a little more and it looks even better. Definitely recommend.
nice setup been thinking of doing something similar.
Related
I thought I'd share this here, in case anyone is interested, and to not go off topic in this thread in the Q&A section that was interested in some detail of my build.
I couldn't find an aftermarket stereo that was as customizable, or had as many features as I'd like. My car is a 02 Mitsubishi Lancer which also is designed for a single DIN stereo, which limited my selection as well. I decided a while back that I wanted to attempt a tablet dash install, and when the Nexus 7 came out, I decided it was time to start on this project.This was my first attempt working with fiberglass, bondo, vinyl wrap, and I'm sure a few other aspects of the project I'm missing.
I failed to take pictures at all steps, as it was trial and error for awhile anyways. Here are some photos of some of the process and a parts list.
Also my Home Screens I created for this very purpose.
Parts List:
Nexus 7
4 Channel Amplifier
Four Gauge Power & Ground Wires
Speaker Wire Cable
2 RCA Plug Cable
3.5mm Stereo Male to 2RCA Male Cable
1/Female to 2/Male Y Connector Cable x 2
RCA Volume Level Control
AC Power Inverter
Car-Cigarette-Lighter-Extension Socket
Radio Wiring Harness Adapter
RadioTrim Piece
Fiberglass Resin
Fiberglass Cloth
Bondo
3M Brushed Black Metal Vinyl Wrap
Ground Loop Isolator (Optional)
Semi Finished Final Product
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
RadioTrim Piece found in a junkyard that I cut the innards out of and filled with fiberglass and bondo. My car dash originally looks something like this.
So I had to create something that would house a 7" tablet, and also relocate my temperature controls.
Radio Trim Piece covered with Adhesive Promoter and paint.
Nexus 7 without Radio Trim. Backing is a piece of pegboard cut to fit in dash.
Radio Trim without tablet
Volume Control Knob
Cadence 4-Channel 1000 Watt Amp
Power Inverter
Amazing.. so I'm assuming you tether off a hot spot of some sort?
crachel said:
Amazing.. so I'm assuming you tether off a hot spot of some sort?
Click to expand...
Click to collapse
Thank you, yep, I still have the original Evo 4G for my phone. I just have a tasker shortcut to toggle a Portable Hotpsot. It's only 3G but its worked pretty well so far
looks nice! the work with the fibre glass is very good!
the only issue I have is the use of an inverter, couldnt you have got a in car usb adapter? as this would mean 1 less power conversion.
Assuming you're leaving the Nexus 7 in the dash, aren't you worried about the heat?
markp1989 said:
looks nice! the work with the fibre glass is very good!
the only issue I have is the use of an inverter, couldnt you have got a in car usb adapter? as this would mean 1 less power conversion.
Click to expand...
Click to collapse
Thanks, I was just going to use a USB adapter, but I tried the 3 I already owned, and none of them would register it was charging. I bought a 4th that I thought would do the job, and had the same problem. I'm sure its possible with the right charger, and I may end up switching it out later. I just ended up being impatient and went with the inverter lol.
jabsys said:
Assuming you're leaving the Nexus 7 in the dash, aren't you worried about the heat?
Click to expand...
Click to collapse
That is a concern. It's been in the car for maybe 24 hours now and no problems yet, but I plan on running out to my car to check it on my breaks and lunch tomorrow and probably throughout the work week to see how it holds up. If it becomes an issue I may need to take it out, if the car will be sitting for long stretches of time, or find another solution.
I saw a thread awhile back where someone else bought some sun shades to try and keep the temperature down inside the car. I guess we'll see how it holds up over the next few days.
Somebody put a nook color in a ...Wrangler I want to say? He didn't seem to have any trouble leaving it in there.
Yeah, here it is.
mateorod said:
Somebody put a nook color in a ...Wrangler I want to say? He didn't seem to have any trouble leaving it in there.
Yeah, here it is.
Click to expand...
Click to collapse
I think his was on a dock. I know one guy had his in a smart car as well. Here.
Looks good though. I've thought about doing it in my car with my NC.
Nice job. Looks good.
Sent from my Nexus 7 using xda app-developers app
Looks cool man
mateorod said:
Somebody put a nook color in a ...Wrangler I want to say? He didn't seem to have any trouble leaving it in there.
Yeah, here it is.
Click to expand...
Click to collapse
biohazrd51 said:
I think his was on a dock. I know one guy had his in a smart car as well. Here.
Looks good though. I've thought about doing it in my car with my NC.
Click to expand...
Click to collapse
Thanks, good to hear others havent had overheating issues with similar installations.
I've been looking into this stuff for the last couple months now and I don't think I've seen either of those two builds, thanks.
I know this instructables build and too many random YouTube videos to list on different in-dash installs is what got me finally started in on this project.
You might want to consider some kind of retractable or removable cover. Couple of reasons. One...it can keep direct sunlight off the unit. That would probably be the biggest issue with this setup. Second, it would deter theft. Generally, a thief might not risk breaking into a car to guess what's behind curtain #1...if you know what I mean. However, seeing a full blown tablet in a home made setup (e.g. not built into the vehicle/easy to steal) might be too tempting for some crack head.
Mostly blocking indirect sunlight though...
had an acer a100 perm installed in my dash for several months even here in sunny florida i only got heat warnings when the sun was directly hitting the tablet, using a windshield shade when parked was sufficient to keep the heat warnings from coming on
i'm waiting for the pogo pin dock to be released before the nexus 7 gets a spot in the dashboard, i dont want a perm install again as i like using this tablet outside of the car too
ExploreMN said:
You might want to consider some kind of retractable or removable cover. Couple of reasons. One...it can keep direct sunlight off the unit. That would probably be the biggest issue with this setup. Second, it would deter theft. Generally, a thief might not risk breaking into a car to guess what's behind curtain #1...if you know what I mean. However, seeing a full blown tablet in a home made setup (e.g. not built into the vehicle/easy to steal) might be too tempting for some crack head.
Mostly blocking indirect sunlight though...
Click to expand...
Click to collapse
b22ri22an said:
had an acer a100 perm installed in my dash for several months even here in sunny florida i only got heat warnings when the sun was directly hitting the tablet, using a windshield shade when parked was sufficient to keep the heat warnings from coming on
i'm waiting for the pogo pin dock to be released before the nexus 7 gets a spot in the dashboard, i dont want a perm install again as i like using this tablet outside of the car too
Click to expand...
Click to collapse
Thanks for the tips, and again its good to hear these reports of other tablet installs with minimal overheating issues. I checked on it today at lunch and it was hot to the touch, but functioning fine, i believe the temperature on the tablet read 134 F..... It was maybe 80 here outside in WI today. I think I'll definitely be investing in a windshield shade to be on the safe side at the very minimum.
I have a Transformer Prime for my other tablet and at this point I was going for a perma install look, although it isn't all too difficult to remove from the dash if needed.
ahavens17 said:
Thanks for the tips, and again its good to hear these reports of other tablet installs with minimal overheating issues. I checked on it today at lunch and it was hot to the touch, but functioning fine, i believe the temperature on the tablet read 134 F..... It was maybe 80 here outside in WI today. I think I'll definitely be investing in a windshield shade to be on the safe side at the very minimum.
I have a Transformer Prime for my other tablet and at this point I was going for a perma install look, although it isn't all too difficult to remove from the dash if needed.
Click to expand...
Click to collapse
Oh AHeavens, you're a neighbor then. So you know we top the hundreds a few weeks every summer. So if a 80 degree day warms the tab to 135, imagine what one of our 105 days would do to it!
Not to mention our winters where it gets to -35 to -40!
Sent from my Nexus 7 using Tapatalk 2
Nice install! i've never had the courage to break out the bondo!
I've installed the Nexus 7 in my WRX too. The trick to getting USB charging to work via a cig adapter is to put a USB hub inline. I pulled apart a tomtop GPS charger and wired it into the factory stereo wiring then plugged a USB hub into it and then the N7 (and my Galaxy S3) into the hub and they both charge nicely.
Having trouble with the audio output though, it is horrible... it buzzes every time i touch the screen and it buzzes when wifi is active and it is just generally crap.
I would like to plug in a USB soundcard (DAC), something like the Fiio E10 but then i wouldn't be able to charge the tab while USB OTG is active.
I was hoping that the pogo pins on the side would allow charging whilst the USB dock connector could be used for OTG but it doesn't look like it will work since both the pogo pins and USB connector go to the same usb switch internally.
I might put up a thread on my WRX N7 install.
edit: here it is: http://forum.xda-developers.com/showthread.php?t=1819175
another edit: there seems to be a thread on the charging issues... i have also just found that my tab drains it's battery faster than it can charge it...
http://forum.xda-developers.com/showthread.php?t=1791717
The ultimate car install: http://www.youtube.com/watch?v=j0o1zkqEuec&feature=youtube_gdata_player
Sent from my Nexus 7 using xda app-developers app
I put my nexus 7 in my dash for 3 hours one day it turned off on me... I assume because it was too hot.
For now I remove it when I get to work and leave it in the car when I am home. I have no issues in the garage. Only problem is the place I mounted mine is a perfect fit and no room for the usb charging cable till I modify the hood but I am hoping for the pogo dock soon.
Sent from my Nexus 7
kangxi said:
The ultimate car install: http://www.youtube.com/watch?v=j0o1zkqEuec&feature=youtube_gdata_player
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Nice!
How are they getting connected? Bluetooth, wifi tether, hotspot, ...?
when I get a car I would definitely spend the $250 bucks to have a really sexy media player in the dash
Hey guys/gals,
Thought i would share my most recent project with you all in the hopes of getting some advice and feedback and showing off my install
This will be an incremental build thread, i'll add to it as i get more pics and work my way through some issues.
I have installed a Google/Asus nexus 7 in the dash of my MY00 Subaru WRX. I trialled the optus mytab (AKA ZTE V9) in the dash but it didn't last more than a day since it was a piece of crap performance and audio-wise.
After spending a few months building a nano-itx double din touch screen pc to go in the dash, i changed my mind (for the millionth time) and decided to stick an android in there instead. The intel PC is now sitting in a box at home doing nothing...
The biggest trouble was finding a tablet that would fit in below the A/C controls nicely.. in the end, the N7 was about 3mm too big bit i broke out the dremel and made it fit!
Having trouble with the audio output though, it is horrible... it buzzes every time i touch the screen and it buzzes when wifi is active and it is just generally crap.
I would like to plug in a USB soundcard (DAC), something like the Fiio E10 but then i wouldn't be able to charge the tab while USB OTG is active.
I was hoping that the pogo pins on the side would allow charging whilst the USB dock connector could be used for OTG but it doesn't look like it will work since both the pogo pins and USB connector go to the same usb switch internally.
another edit: there seems to be a thread on the charging issues... i have also just found that my tab drains it's battery faster than it can charge it... I'll have to look into this further: http://forum.xda-developers.com/show....php?t=1791717
Parts list:
ASUS Google Nexus 7
4 Channel Nakimichi Amplifier
Single Channel Class-D 1000W Nakimichi Subwoofer amplifier
Four-Gauge power/ground
Gold plated Ground splitter and +12v Splitter/Circuit Breaker
Oxygen-Free Copper speaker cables (around 12 gauge)
(coming soon) 1.5 Farad Capacitor (to stop headlights dimming)
2 x Kenwood 1200W Subwoofers
4 x Focal 6" Splits
Good quality RCA cables
R/A 3.5mm headphone plug to 2x RCA 30cm cable
R/A Micro USB cable
gutted tomtom GPS charger
(coming soon) RCA volume level control (thanks for the idea ahavens17)
20mm wide metal strips
Hook and Loop velcro
Rubber trimming/edging
Update: Added some more pics showing my crude but effective way of holding the tablet in-place.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
To hold the tablet in place, i have used some metal straps cut to size that are screwed on using the screws that hold the top of the ash tray to the dash fascia. I stuck some velcro on to the metal straps and 2 small strips on the back of the tablet to dampen vibration and stop the tablet sliding around sideways. The velcro also stops the metal straps from marking the back of the tablet (not that it matters since it is hidden behind the dash)
You can see how it is done in the pictures above. Also, I am using right-angle micro USB and audio connectors so that they fit nicely in the dash
My blog of the install is here: Finniss.net
you may or may not find more updated info there as time goes on.
Dude, that's awesome! Good work!
Sent from my Nexus 7 using xda premium
How easy is removal?
Sent from my Galaxy Nexus using Tapatalk 2
Looking to do the same thing in my 2000 outback!
Sent from my Galaxy Nexus using xda app-developers app
I'm not talented enough to do this to my car. I just have to lay my tablet on the passenger seat.
I'm not that talented either but will just end up using a dremel and some Velcro or something lol
I have a huge double din slot so I won't have to do much cutting at all I will have to buy a cheap 40$ radio to put where my 6 disc CD changer in so I an use that as my AUX input as I am not buying an amp using stock speakers plus I would like to use FM just for sometimes you know lol and possible CDs
Now what would be super cool is to have your tablet start your car when you NFC bump it! Someone work on it!
Sent from my Galaxy Nexus using xda app-developers app
Wordlywisewiz said:
Now what would be super cool is to have your tablet start your car when you NFC bump it! Someone work on it!
Click to expand...
Click to collapse
I'll get to work. what a cool idea! "get in the car, tap it with S3, brooom!"
curseddagger said:
I'll get to work. what a cool idea! "get in the car, tap it with S3, brooom!"
Click to expand...
Click to collapse
Might have issues with newer cars but my 2000 out back should have no issues with being "NFC Hotwired" lol
Edit check this out
https://www.youtube.com/watch?v=C9H54r6AUNA&feature=youtube_gdata_player
Idk how but he has digital gauges on his tab
Sent from my Galaxy Nexus using xda app-develope
rs app
Wordlywisewiz said:
Might have issues with newer cars but my 2000 out back should have no issues with being "NFC Hotwired" lol
Click to expand...
Click to collapse
Heh yeah, mine has a brandt alarm system on it with a keypad which may pose a challenge but not something that i am totally unfamiliar with ;P
p.s. that sounds dodgy... I have spent many hours messing with that stupid alarm system to avoid having to tow the car back to subaru head office when the alarm system dies (which it frequently does, requiring replacement)
Wordlywisewiz said:
Idk how but he has digital gauges on his tab
Click to expand...
Click to collapse
Looks like he is using a bluetooth -> OBDII engine diagnostics cable and the android car home app. I've toyed with this before too and it's setup on my Nexus 7 now
wyattyoss said:
How easy is removal?
Click to expand...
Click to collapse
It's not a slide in/out setup like i would love it to be but the plastic surround around it easily pulls off and the tab can then be removed.
When i get home, i'll get some more pics of how it is held in place, etc.
I'm thinking this but I'm gonna do it motorized
http://www.mp3car.com/android-table...-car-sliding-dock-using-hacked-dvd-drive.html
Sent from my Galaxy Nexus using xda app-developers app
Such an awesome stereo replacement!! awesome mod...might do that tomytruck...1st..i gotta buy the nexus7 lol
Sent from SAMSUNG -SGH -I717 | FJ's UCLF6 B4
cougar11 said:
Such an awesome stereo replacement!! awesome mod...might do that tomytruck...1st..i gotta buy the nexus7 lol
Sent from SAMSUNG -SGH -I717 | FJ's UCLF6 B4
Click to expand...
Click to collapse
I gotta buy it also
Sent from my Galaxy Nexus using xda app-developers app
This is actually why I bought the nexus 7. I have a car pc now with an 8" lcd but it fried itself a month ago. Just haven't gotten around to figuring out how to mount the Nexus 7. Bluetooth works great in my truck via my JVC deck. I stream from my phone all the time. I just wish there was a Google Now "car home". It'd be really nice to have voice control over everything with a decent looking interface.
You got me interested. Keep up the work. Can't wait to see the final setup.
I'm going to be leaving my stock radio intact, and using a ProClip mount. That way it will still look good and I'll still have a radio, and cd player.
Actually, the proclip for my car installs in a matter of seconds and disappears just as fast, so it will still retain the stock look.
I've already run an ipod2car to my changer inputs, then converted that so I can use it as an ipod cable, or an aux in. Then I plug in an htc stereoclip into the aux in for bluetooth. So it will be wireless to the factory deck. All of that stuff is hidden in the dash so all I have exposed is the little aux input and the bluetooth receiver.
I have to do it this way because my radio is in a piece that goes all the way across the dash, and isn't in a modular center console piece that I can pop out and work with. So If I put it "in" the dash.. it would be permanent and I'd have to do all the amps.
I'll post pictures once they make the mount for the nexus and I get it in. For now it just rides in the passenger seat.
The gauges are from an app called Torque, and it uses a bluetooth OBD2 reader that can be found on amazon. It's good for getting some basic numbers, and even allows logging. But there is a slight delay and well, it isn't much compared to my HP Tuners for my car but that's not saying much. it is definitely a must have for any car installations.
Idk I might not end up doing it I think my timing belt is more important along with getting my exhaust fixed....
Plus its an Asus Tablet and I had bad experiences with them with the prime....
Plus me being 17 and just getting my lisence idk if I should be distracted while driving
Sent from my Galaxy Nexus using xda app-developers app
I am interested in this as well.. I just put a cheap double din DVD player in my 01 forester and I would totally send it back and use that $200 to buy a nexus 7.. I just want to figure out how I could mount it and still be able to remove it with out taking the dash apart.. The other thing is what is the best way to get your audio to your speakers if you dont have a amp installed? I guess I could just get a small cheap amp if I needed to.
I'm running a Samsung galaxy tab in the dashboard of my Kia soul, 2010 sport model, for over a year now.
A lot of whine and stuff to the stereo, but then I got a 3.5 mm cable with a ground loop isolator on it. Did you get one of those? It solved my problems.
A couple members on my website, soulhamsters.com, are also using Nexus seven and other tablets in their dashboards.
Blasted from my HTC Rezound (Zone23s Newtified 3.2.1)
Windshield mounts are illegal here, which is fine considering it's not an SUV/truck, and vision is limited.
On my phones I use a small mount that clips into the central heater vent. It's not pretty, but it works very well.
Has anyone found a solid version of something like that, for the Nexus 7?
As nice as some of the custom installs here look, I'm not interested in replacing my stereo or any panels.
I'm just at a loss for if there is something like what I use for my cell phone, but on a larger scale. It would have to clip into the heater exhaust, and be solid enough to safely hold a tablet, but also crush down when not in use. Or if there's a good alternative, I'd be glad to try it.
If the mount can support a small case as well, and crush down into place, that would be a bonus.
Many thanks!
--bb
Mountek!
Goes right in the CD Slot you can still use the CD player without any issues. I just leave that one cd in there and normally use bluetooth for all videos and music.
They don't make it official for tablets yet very slow company. But the current one they offer can easily be used for Nexus 7 with just opening and removing 2 parts (very easy) and secure.
This does not block your heating vents or the windshield
raiseup151z said:
Mountek!
Goes right in the CD Slot you can still use the CD player without any issues. I just leave that one cd in there and normally use bluetooth for all videos and music.
They don't make it official for tablets yet very slow company. But the current one they offer can easily be used for Nexus 7 with just opening and removing 2 parts (very easy) and secure.
This does not block your heating vents or the windshield
Click to expand...
Click to collapse
Looks interesting....can you elaborate on how to mod it to fix the Nexus?
I don't think that the nexus 7 could be attached to something that would clip into the vent. I think it would be too heavy. I have one of those kinds of mounts for my phone, but it seems to have worn out after a while.
Couldn't you put some sort of a plastic disk onto your dashboard and mount it there? Or would that still be considered obstructing your view and not allowed?
Pro-clip makes mounts specific to your car with very little "install"
http://www.proclipusa.com/brodit-device-holder/asus/nexus-7-google.aspx
adamhlj said:
I don't think that the nexus 7 could be attached to something that would clip into the vent. I think it would be too heavy. I have one of those kinds of mounts for my phone, but it seems to have worn out after a while.
Couldn't you put some sort of a plastic disk onto your dashboard and mount it there? Or would that still be considered obstructing your view and not allowed?
Click to expand...
Click to collapse
My dashboard is much too rounded to allow for that.
However, I just watched a video in the XDA forums that gave me an idea. I could probably mount one of those disk style setups underneath my dashboard, and rotate it upwards. I'm just not sure how well it would hold the weight.
My car is identical to the one here: http://www.carparts.com/roadtests/hondaciviccoupe/photos.htm
The center area protrudes out a fair bit, and while it's hard to see, it's not flat right above the radio. But it is flat underneath the center console.
Maybe I'll give the exomount a try, and see if it holds in place ok.
I saw a while back a clever use of a metal coat hanger and shrink wrap tubing to make a mount for an ipad. Simply bending it to hook onto your heat vents and then shrinking the tubing so it doesnt scratch the crap out of your nexus is the only real setup to it.
I cant put the link cause I'm new to the forum, but its on instructables and just search tablet car dock coat hanger. Its one of the first few results. The title is "How to custom tablet car dock for under 15 bucks".
I guess sheet metal was involved too, making it more complicated than i thought. But, that was for a 10-incher, perhaps with a lighter tablet that isnt necessary? Just a thought, figured I'd put my two cents in.
bladebarrier said:
My dashboard is much too rounded to allow for that.
However, I just watched a video in the XDA forums that gave me an idea. I could probably mount one of those disk style setups underneath my dashboard, and rotate it upwards. I'm just not sure how well it would hold the weight.
My car is identical to the one here: http://www.carparts.com/roadtests/hondaciviccoupe/photos.htm
The center area protrudes out a fair bit, and while it's hard to see, it's not flat right above the radio. But it is flat underneath the center console.
Maybe I'll give the exomount a try, and see if it holds in place ok.
Click to expand...
Click to collapse
Hey blade. Do you have that little opening right underneath the radio? The one with the little door in front? I've seen cool installs using that opening and a dash/window mount attached inside. either suction cup to the inside, or using the dash mount disc thing
Sent from my Nexus 7 using Tapatalk HD
Awexit76 said:
Hey blade. Do you have that little opening right underneath the radio? The one with the little door in front? I've seen cool installs using that opening and a dash/window mount attached inside. either suction cup to the inside, or using the dash mount disc thing
Sent from my Nexus 7 using Tapatalk HD
Click to expand...
Click to collapse
I sure do! That's where the line in to the car stereo is running.
That's some good thinking right there.
Thanks!
If you have a few air vents, you can try the breffo spiderpodium. The normal size works. There is a tablet version, but those are meant for larger tablets. The normal size works fine. I had an imitation spiderpodium, but the concept was the same. You wrap around to hold the device and then use a few of the "legs" to stick into the air vents.
Here is a pic . But I can attest to that the arms will hold and because the arms are pretty long, they can slip into the air vents and are pretty stable. YMMV.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here is one with a HTC Thunderbolt and spiderpodium
This thread
http://forum.xda-developers.com/showthread.php?t=1947967&highlight=car+mount+hack+guaranteed
This Post
http://forum.xda-developers.com/showpost.php?p=33074377&postcount=1
And this post
http://forum.xda-developers.com/showpost.php?p=33401295&postcount=28
Inexpensive and it just works.
bladebarrier said:
I sure do! That's where the line in to the car stereo is running.
That's some good thinking right there.
Thanks!
Click to expand...
Click to collapse
Would love to see what your final product is.... Keep us posted
Sent from my Nexus 7 using Tapatalk HD
Off topic but cool nonetheless IMO LOL....
I decided NOT to mount the N7 and just use it as a Nexus 7 HUD I am using the Seidio Active case, where the rubberized case grips the dash pretty well. No sliding what so ever on the drive home. :good:
kpjimmy said:
Off topic but cool nonetheless IMO LOL....
I decided NOT to mount the N7 and just use it as a Nexus 7 HUD I am using the Seidio Active case, where the rubberized case grips the dash pretty well. No sliding what so ever on the drive home. :good:
Click to expand...
Click to collapse
Hah! That's pretty cool looking. What's the app?
kpjimmy said:
Off topic but cool nonetheless IMO LOL....
I decided NOT to mount the N7 and just use it as a Nexus 7 HUD I am using the Seidio Active case, where the rubberized case grips the dash pretty well. No sliding what so ever on the drive home. :good:
Click to expand...
Click to collapse
Second this...how is that achieved? Totally awesome!
bladebarrier said:
Windshield mounts are illegal here, which is fine considering it's not an SUV/truck, and vision is limited.
--bb
Click to expand...
Click to collapse
The Windshield mount is not the way to go, and nither is the vent mount.
This is what you are looking for. http://www.amazon.com/Kropsson-Univ...&qid=1343154299&sr=1-1&keywords=Kropsson++800
Its currently sold out at Amazon, but a quick Google search of the products name, will find you one.
I have this products big brother, sold through ExoGear, to hold my old Xoom tablet. http://www.amazon.com/gp/product/B006JJZCAO/ref=oh_details_o03_s00_i00
Its actually quite a fantastic mount and is very customisable in terms of articulation, height adjustment, and vibration.
Im eventually going to do a full in-dash modification of my BMW E46 with my Nexus7, but until then, this is what Im rocking.
bladebarrier said:
Hah! That's pretty cool looking. What's the app?
Click to expand...
Click to collapse
syypher said:
Second this...how is that achieved? Totally awesome!
Click to expand...
Click to collapse
LOL my 4 yr old loves it. She counts with it haha....
The app I use is Ulysse Speedometer app, the free version.
https://play.google.com/store/apps/details?id=com.binarytoys.speedometer
I may get the paid version because it's a good app and doesn't need an ODBII Bluetooth, which I have lol. And saying that, for all you that have Torque (pro or free) there is a HUD function there as well. You have to play around with the different themes and dials to get the set up you want. However, the torque app requires the OBDII BT dongle depending on what you want to monitor. Not too sure if you can run it without it. I have the OBDII in my Tribute but on my 6, I do not so this app works well and the color can be changed to closely match your dash lights if you prefer, which I do lol.
Oh and to report back. I was using this HUD from the N7 in the 6 last night (Mazda 6 sedan), which I have modified a bit so this fits perfectly lol. But nonetheless the dash didn't accommodate the tablet too well and in this instance the tablet did move a tad. Not too much when going around the corners, but will move if you corner at 50mph lol. So in that case, I suggest a cheapie sticky pad to grip the tablet in this case. YMMV, in your case, it may work fine depending on your dash. Have fun!
---------- Post added at 10:32 AM ---------- Previous post was at 10:28 AM ----------
ritalin said:
The Windshield mount is not the way to go, and nither is the vent mount.
This is what you are looking for. http://www.amazon.com/Kropsson-Univ...&qid=1343154299&sr=1-1&keywords=Kropsson++800
Its currently sold out at Amazon, but a quick Google search of the products name, will find you one.
I have this products big brother, sold through ExoGear, to hold my old Xoom tablet. http://www.amazon.com/gp/product/B006JJZCAO/ref=oh_details_o03_s00_i00
Its actually quite a fantastic mount and is very customisable in terms of articulation, height adjustment, and vibration.
Im eventually going to do a full in-dash modification of my BMW E46 with my Nexus7, but until then, this is what Im rocking.
Click to expand...
Click to collapse
I was looking at that a few weeks ago but opted for the Kroppson Aero that fit both my sensation and N7, but just barely. I wouldn't recommend the Aero FYI, the mount you have works better IMO. Now that I am getting a N4 added to the family, which is a bit longer, this may fit both devices as well.
ritalin said:
I have this products big brother, sold through ExoGear, to hold my old Xoom tablet. http://www.amazon.com/gp/product/B006JJZCAO/ref=oh_details_o03_s00_i00
Its actually quite a fantastic mount and is very customisable in terms of articulation, height adjustment, and vibration.
Click to expand...
Click to collapse
I ended up ordering the ExoGear through Ebay (there are some sellers in the US, and they give free shipping, at the same price Amazon used to sell it for). Should be here today or Monday. Will post a pic of it once I decide how I'll set it up in the Civic.
What's the car app you're running there, or is that a modified UI of widgets? It's a nice setup.
also check out http---brodit.se, they have the nexus 7 mounting kit + car specific adapters for diverse mounting options which do not require any mods to the car.
ritalin said:
The Windshield mount is not the way to go, and nither is the vent mount.
This is what you are looking for. http://www.amazon.com/Kropsson-Univ...&qid=1343154299&sr=1-1&keywords=Kropsson++800
Its currently sold out at Amazon, but a quick Google search of the products name, will find you one.
I have this products big brother, sold through ExoGear, to hold my old Xoom tablet. http://www.amazon.com/gp/product/B006JJZCAO/ref=oh_details_o03_s00_i00
Its actually quite a fantastic mount and is very customisable in terms of articulation, height adjustment, and vibration.
Im eventually going to do a full in-dash modification of my BMW E46 with my Nexus7, but until then, this is what Im rocking.
Click to expand...
Click to collapse
Deff would like to know what car app that is! Thanks
I've narrowed it down to these 3
http://www.ibolt.co/ibxs-33603
http://www.amazon.com/gp/aw/d/B004G1L52Q
http://www.amazon.com/gp/aw/d/B007BCJKQA
The first one looks optimal because of that cord that connects to only one side of the phone and can connect to the car charger and the aux. ( shows around 1:30 of the video )
Tried googling for a cord like that but couldn't find any... if there are cords like that sold separately I may consider the cd one more.
Please let me know your opinions and if there are any cords like that.
Ibolt had a rocky start with their presale...but if they get their **** together, I would recommend their product.
swyped all these spelling errors from my galaxy note 2
finalhit said:
Ibolt had a rocky start with their presale...but if they get their **** together, I would recommend their product.
swyped all these spelling errors from my galaxy note 2
Click to expand...
Click to collapse
what happened to them? what did they do wrong
See here:
http://forum.xda-developers.com/showthread.php?t=1910428
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
dakleenupman said:
See here:
http://forum.xda-developers.com/showthread.php?t=1910428
Sent from my SAMSUNG-SGH-I317 using xda app-developers app
Click to expand...
Click to collapse
yeah i read a couple pages already.
i guess they are looking to upgrade a new version?
so i should wait till their next product comes out?
I have the ibolt dock and am hapoy with it now that they shipped the charging arm. What I like is that it will hold other phone in the future not just the note2
Flexia32 said:
I have the ibolt dock and am hapoy with it now that they shipped the charging arm. What I like is that it will hold other phone in the future not just the note2
Click to expand...
Click to collapse
pretty sure most of these other ones hold most phones as well.
i just kinda have a thing for it blocking my view, rather it be on the cd slot but i like the cord where it can connect to charge and aux from only 1 plug on the phone
was wondering if there are any cords like that sold separately
DeveloperOptions said:
The first one looks optimal because of that cord that connects to only one side of the phone and can connect to the car charger and the aux. ( shows around 1:30 of the video )
Tried googling for a cord like that but couldn't find any... if there are cords like that sold separately I may consider the cd one more.
Please let me know your opinions and if there are any cords like that.
Click to expand...
Click to collapse
ibolt are supposedly going to sell the chord separately, though I don't know when they open to do so. I bought the official s3 dock and will be buying that ibolt cable once it's available.
Sent from my GT-N7100 using xda premium
http://www.clingobyallsop.eu/car-mounts/universal-car-phone-mount
I just buy this car mount and is the best i can find untill now...i like because u only grip to the phone back...
Sent from my GT-N7100 using xda premium
lucian75 said:
http://www.clingobyallsop.eu/car-mounts/universal-car-phone-mount
I just buy this car mount and is the best i can find untill now...i like because u only grip to the phone back...
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
I keep hearing reviews that the cling part gets gummy in the heat. I stayed away from that one since I'm in Florida and it gets pretty hot here most of the year.
I too am on the hunt for the perfect car mount... I'm leaning towards the mountek just because I'm tired of the suction cup models not sticking to the dash, and the vent models don't work for me.
nmw407 said:
I keep hearing reviews that the cling part gets gummy in the heat. I stayed away from that one since I'm in Florida and it gets pretty hot here most of the year.
I too am on the hunt for the perfect car mount... I'm leaning towards the mountek just because I'm tired of the suction cup models not sticking to the dash, and the vent models don't work for me.
Click to expand...
Click to collapse
You'd be correct sir. When the gummy part heats up from being in the sun for a while (or from dust collecting), your phone will shoot off the minute you break hard.
My old HTC One X took a few tumbles from a similar gum-based mount. If you're using in a stationary function, say on a desk or wall near a desk, it'd probably be ok.
How hard do you want to work for it and how much do you care what it looks like?
I butchered a HTC HD2 dock to work. It looks good (subjective of course but there's almost no clips and wires and latches and junk, very minimal) and it's secure (it is suction cup, it's just been a good working suction cup for me) includes usb charging, one handed not a ugly little cable hanging off to the side.
But it was kind of a ***** flipping the usb port over and still having it point at the right angle and not bugger up the wire connecting to it. But all in all took less than two hours and I love it every minute I'm in the car, so, worth it.
ProClip makes an even more convenient mount as far as using it. Like a slot you drop the phone in, no aiming, requires no attention at all. Usb charging. Very stable. But ugly. In my truck it would be fine but in my nice car I just don't want to look at something so blocky and mechanical if I can avoid it. It's not the worst by far in that respect but I just like better if it's possible. Also it's $100 in two parts. If it looked better I'd have no problem with that. The HD2 mount was 70 I think but it served the entire lifespan of my og evo and now works for my gn2 so that 70 is pretty good by now.
The new ibolt one? Blech. Well it looks a little better than most commodity universal mounts. The aluminum rails are at least cooler than the usual all black plastic. But to me it's only a slight improvement. It's still a generic crappola universal gps/phone clamp like all the rest. It's one unique feature is the special usb cable that will trigger smart dock mode. But thanks to Samsung there is no distinct car mode detection, just smart dock mode. So if you assign that to a car home app, you get the car home everywhere i cluding your desk and nightstand. We can use nfc tags and get a better result than that with no special cable. So it's back to being a completely generic, ugly, inconvenient, holder.
The next best option I've seen is this universal one that has springloaded grabber arms, but they have it set up for one handed operation. The arms are open when the dock is empty. When you put the phone in it presses a button that releases the arms to close on the phone. It's surprisingly secure. I shook the mount all around trying to shake the phone free.l and it didn't budge. When the arms close, two buttons pop out at the same time opposite each arm, on oposite sides of the phone. To release the phone you just grab the phone, and your thumb & forefinger are already right there on those two buttons. Press the buttons together and that opens the arms. So you are releasing the phone and grabbing the phone in the same motion. It works quite well. No usb built in but the port is exposed to use your own cable. Looks are fair. They are are thin and unobtrusive compared to many and there's only two arms on the sides and two resting pegs on the bottom. You could hack those rests right off and it would work exactly as well and look significantly neater. Suction cup base. It's called Smart Tap.
Another option is someone Someone on xda here came up with a pretty clean hack of the original note mount. No filing, just a little heat gun softening.
I never heard of Mountek so thanks for the clue I'll check it out.
There is really no "good" solution for the this phone yet.
Sent from my SPH-L900 using xda premium
I ordered one the "iMagnet Cradle-less Magnetic Mount with Quick-snap Technology". It should be here tomorrow. I'd post a link, but I haven't gotten enough posts in to get that ability, even though my account is pretty old.
It's one of the magnetic mounts. You stick a metal disk on your phone/case and bam. Has good reviews, so I thought i'd give it a try.
lucian75 said:
http://www.clingobyallsop.eu/car-mounts/universal-car-phone-mount
I just buy this car mount and is the best i can find untill now...i like because u only grip to the phone back...
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
yeah i saw a couple bad reviews on that as well so it kinda turned me off, i'd rather get something that's more secure.
i really like the ibolt cable, not a big fan of suction cups either so the mountek looks optimal if only i could get that cable separate i might just end up getting ibolt because of the cable
you guys have given some really good insight,i will check out the hd2 as well and see if i could get that to work haha.
about the smart dock mode, i don't have any other dock elsewhere so that's not an issue for me, but it doesn't go into dock mode if i plug in usb to connect to the computer or plug it into my charger does it?
I just got the iOtti mount for mine. I LOVE it!
Here's my "review": http://forum.xda-developers.com/showthread.php?t=1982558&page=3
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Beamen1 said:
I just got the iOtti mount for mine. I LOVE it!
Here's my "review": http://forum.xda-developers.com/showthread.php?t=1982558&page=3
Click to expand...
Click to collapse
Not sure where you are located, but I guess we are far away from summertime to test it out if it stays stuck to the surface? I was looking at this case as well, until read in another forum about people having issues with a sticky part of the suction cup especially when it gets hot outside. Maybe it was a defective batch or whatever. That kind of put me away from buying it, plus I was waiting for Arkon to release their slim grip ultra mount with a sticky suction cup I actually have it coming my way next week and will review it once I get it. But I don't think it has any release buttons, etc. like their other grip mount I had for my DX. I guess I'm still on the fence until I get it and test it out. But I'm definitely glad iOttie is working out for you! I just wish they would drop "i" cause I'm sure a lot of android people buying their mounts as well lol!!!
The one from iOttie on amazon is worth every penny it works too well lol make sure where you it is where you want it cause it sticks like rubber cement!
Sent from my SGH-T889 using xda app-developers app
sleepy8686 said:
The one from iOttie on amazon is worth every penny it works too well lol make sure where you it is where you want it cause it sticks like rubber cement!
Sent from my SGH-T889 using xda app-developers app
Click to expand...
Click to collapse
So once you release a suction cup latch you have to pry it off the dash board with a butter knife? Will it take off dashboard textured layer or so? Not sure if you were kidding or serious about it sticking like cement
vectron said:
So once you release a suction cup latch you have to pry it off the dash board with a butter knife? Will it take off dashboard textured layer or so? Not sure if you were kidding or serious about it sticking like cement
Click to expand...
Click to collapse
He is not kidding. Read the Amazon reviews. This thing sticks to anything and the quick release is a GOD sent. It's SO easy to take the phone in and out of the mount, and once you put it in the mount it isn't going any where. Lots of adjustable settings. I LOVE it.
On my previous mounts I didn't even use them that often (only when I needed GPS), but this thing is so easy to take in/out that I do it every time I drive the car. It is worth every penny for sure!
I used my 50% off at Samsung.com and got the universal there. Loving it.
http://m.samsung.com/us/mobile/cell-phones-accessories/ECS-K200BEGSTA
Sent from my SPH-L900 using Tapatalk 2
I have an iOttie that I use on my note 4 (I am going to return it, to get the nexus 6). However I noticed that the nexus will be too wide for the car mount. Does anyone know a similar mount that will fit this phone?
Not off hand. I wish they would release an official car dock. The one for nexus one and gal nexus were awesome. Nothing released officially for nexus 4 or 5
There's an "iOttie One Touch XL" that holds devices up to 3.5" wide, which should be enough for an N6 plus a case.
I'm planning to get The Air Dock for it.
eksasol said:
I'm planning to get The Air Dock for it.
Click to expand...
Click to collapse
As much as I love wireless charging (and I do I have 5 QI chargers at home I use all the time) it just doesn't work for me in the car. I use GPS and stream music all the time with screen always on. Wireless can't even come close to keeping up to that. I'm sure it will be worse with the N6 screen size too... I am really hoping they release an official car dock this time. Moto seems to be good at doing that so I am hopeful.
bogus83 said:
There's an "iOttie One Touch XL" that holds devices up to 3.5" wide, which should be enough for an N6 plus a case.
Click to expand...
Click to collapse
On iOttie's website FAQs, they list the sizes of each of their mounts. Actually, the One Touch XL only goes up to 3.3", which should be just wide enough for the N6 since it is roughly 3.27" wide. However, it probably wouldn't work if you put a case on it. The only one I can see working if you put a case on it would be the Easy View 2, which has a max width of 3.5".
HOWEVER, I can see another potential issue arising if you want to use a car mount like this. Notice where the buttons are. They are not towards the top of the device like other phones. They are smack dab in the center going down the right side, taking up a good range in the middle of the phone. So you would have to have the mount clamp down on either the top or bottom of the device. I guess we won't know how awkward it would be to use until we have the device in-hand, so we'll see when the phone actually comes out.
Interesting- when I posted that comment there was a graphic on the Amazon listing showing support for up to 3.5. The image is no longer there, so it was likely an error. Too bad.
pseudoSequential said:
I have an iOttie that I use on my note 4 (I am going to return it, to get the nexus 6). However I noticed that the nexus will be too wide for the car mount. Does anyone know a similar mount that will fit this phone?
Click to expand...
Click to collapse
I have the IOttie Easy One Touch XL
MODEL NO: HLCRIO101
It is the best mount I've found to reduce vibration, and super easy to use.
Another iOttie that would work if you need extra distance from your windshield to you, but will vibrate more of course is the iOttie Easy One Touch 2 Universal
MODEL NO: HLCRIO121
Just go with 9to5mac.com ... if they say this one is the best so I won't argue
http://9to5mac.com/2014/11/09/two-o...-by-winnergear/comment-page-1/#comment-224951
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
c4ud4m said:
Just go with 9to5mac.com ... if they say this one is the best so I won't argue
"To be clear, this won’t stay in one place during rapid acceleration and braking"
Click to expand...
Click to collapse
Sounds like a winner! :good:
Click to expand...
Click to collapse
Just found this
I have a Tylt Vu Qi charger for my N4 on my desk at work and I've loved it. I've had it for just about a year now (or has it been 2 I can't remember).
Anyway I ran across this recently and they are advertising it will launch this year. I'm optimistic since Tylt makes such high quality products (from my limited experience)
http://www.tylt.com/vu-car-wireless-charger/
Arioch5 said:
I have a Tylt Vu Qi charger for my N4 on my desk at work and I've loved it. I've had it for just about a year now (or has it been 2 I can't remember).
Anyway I ran across this recently and they are advertising it will launch this year. I'm optimistic since Tylt makes such high quality products (from my limited experience)
http://www.tylt.com/vu-car-wireless-charger/
Click to expand...
Click to collapse
That actually looks like a winner. I'd definitely be interested in purchasing one.
Sent from my GT-N7105 using XDA Premium HD app
I like the magnetic phone mounts. I currently use one from Mountek on my Nexus 5. http://www.mountek.com/shop/
Do you have to use the plate or does it just hold on with the Nexus 5 magnets?
Anything like that but with qi charging?
Thanks
Sent from my Nexus 5 using XDA Free mobile app
I just received this one from Amazon a couple days ago when I was able to get it for $7: http://www.amazon.com/gp/product/B009GSI0MM/ref=oh_aui_detailpage_o02_s00?ie=UTF8&psc=1. Will see how it works out. Keep in mind the buttons are almost smack dab in the middle of the right side of the phone, so you have to be mindful where the grippers will squeeze, or it'll push the buttons.
Inspiration! (Mountek nGrove Grip)
rubi76 said:
Do you have to use the plate or does it just hold on with the Nexus 5 magnets?
Anything like that but with qi charging?
Thanks
Sent from my Nexus 5 using XDA Free mobile app
Click to expand...
Click to collapse
I'm using Mountek nGroove Snap2 with my Nexus5. It's great that I don't have to use any of the plates provided as Nexus5 has wireless charging feature, so the body will stick to the magnet just fine. It is very convenient that I can just throw and it stick easily unlike the hassle of using grip type mount.
Now I hope it will work just fine too with Nexus 6. The non flat back of N6 worries me. maybe I need to modify it so that N6 will not move around when mounted. :fingers-crossed:
digitheatre said:
I'm using Mountek nGroove Snap2 with my Nexus5. It's great that I don't have to use any of the plates provided as Nexus5 has wireless charging feature, so the body will stick to the magnet just fine. It is very convenient that I can just throw and it stick easily unlike the hassle of using grip type mount.
Now I hope it will work just fine too with Nexus 6. The non flat back of N6 worries me. maybe I need to modify it so that N6 will not move around when mounted. :fingers-crossed:
Click to expand...
Click to collapse
I have the same magnetic mount. One of the best purchases I've ever made. I have an iOttie as well but the Mountek is just so much more convenient in that I don't have to slide open the arms to insert or remove my phone.
I have the same concern you do about the curved back. I also use a case and was thinking I'd have to bend the included metal plates to fit between the phone and the case. I absolutely refuse to stick the plate to the back of my case because of the added thickness and the fact that it will just look ugly.
I have the iOttie Easy One Touch 2 Universal Mount (The one that extends), it's a great mount and will fit the N6 without a case. The problem is the button placement on the N6., the mount manages to squeeze the lower volume button when it shuts. Also It will not fit with a case on. Just thought I would let anyone know who was looking into it for a care mount. Again for any other phone this thing is great, best mount I have purchased so far.
RAM X-Grip?
I have been looking into the RAM X-Grip, mostly because of its 4-point "X"-Grip which should avoid pushing any of the hardware buttons.
It is also built like a tank (w/ lifetime warranty) which should lend itself well to any dashboard video recordings should I desire to utilize it for that purpose.
It is relatively expensive ($40-52) but if it out performs (in terms of secure grip & vibration reduction) every other plastic 2-piece pincer style mount then it is absolutely worth the extra investment.
I am still unsure whether the short arm or medium arm length would be best and whether to go with the small or large suction cup option.
I read on Amazon, one pro for the large suction cup (aside from likely better suction) is that the 1" ball (that the arm attaches to) screws on to the suction cup so it can be a bit more versatile (allowing you to screw anything onto the suction cup) should you desire that functionality. Although it appears another option should you desire more versatility from your mount would be to purchase the 1" ball with the plate (w/ screw holes) separately and simply replace the X-Grip mount. This of course means you have the adjustable arm in the system now, but I think that's a good thing.
Last note:
I also read in an Amazon review (and sorta noticed in one video review) there MAY be a bit of play (rotating around the z?-axis, like rotating portrait to landscape) in the X-Grip cradle/mount itself, but more research is necessary to confirm this is actually an issue or just a faulty unit.
First post on XDA
I will be back after further research.