CUSTOM ROM error - HD7 Q&A, Help & Troubleshooting

Device: HTC HD7 T9292
MID PD29100
SPL-1.57.2250.0
SD SANDISK 7580MB Class0
Total storage: 7.20GB
Available Storage: 6.80GB
OS Version: 7.0.7004.0
Firmware revision number: 2250.09.15702.728
Hardware revision number: 0002
Radio software version: 5.71.09.02a_22.51.50.21U
Radio hardware version: A.102.0.D4
Bootloader version: 1.57.2250.0(113571)
Chip SOC version: 2.2.5.0
Please help, i tried to install custom ROM due to some errors i experienced (constant need for HARD RESET due to white HTC logon screen bug; (stuck on bootloader htc screen)). I downloaded the first file DFT_RSPL_WP7FG1_LAUNCH" (also tried revision #3) but it won't change to RSPL...(there were no error messages..it say like it is all done, but it remain spl.) I chose spl 1.56 from list, there weren't 1.57. Therefore i couldn't install HSPL aswell.
Then i tried to install just RUU_Schubert_HTC_Europe_5.10.401.04_SLSPL_Signed_by_ansar". It installed to 100%.. and then says "Invalid image" File is courpted. When i started the phone menu was different a bit. I see some new icons..SingTel IDEAS; SingTel Xplorer; etc..
I should probably point out that i done all this without SIM card inside.
And i had problems with phone in past...it fall a couple of times...my camera is not responding from menu..and i had a "STORAGE CARD NOT WORKING" message.... I don't know is that has to do something with this...but it is better to tell all the informations.
Thanks for the time, any hint would be appriciated.
Thanks,
Nebojsa

nshA said:
Device: HTC HD7 7.5
MID PD29100
SPL-1.57.2250.0
SD SANDISK 7580MB Class0
Please help, i tried to install custom ROM due to some errors i experienced (constant need for HARD RESET due to white HTC logon screen bug; (stuck on bootloader htc screen)). I downloaded the first file DFT_RSPL_WP7FG1_LAUNCH" (also tried revision #3) but it won't change to RSPL...(there were no error messages..it say like it is all done, but it remain spl.) I chose spl 1.56 from list, there weren't 1.57. Therefore i couldn't install HSPL aswell.
Then i tried to install just RUU_Schubert_HTC_Europe_5.10.401.04_SLSPL_Signed_by_ansar". It installed to 100%.. and then says "Invalid image" File is courpted. When i started the phone menu was different a bit.
I should probably point out that i done all this without SIM card inside.
And i had problems with phone in past...it fall a couple of times...my camera is not responding from menu..and i had a "STORAGE CARD NOT WORKING" message.... I don't know is that has to do something with this...but it is better to tell all the informations.
P.S. I would give you more information about the phone, but it seems i messed it preety well with this Custom ROM thing..it won't start anymore; i can't go to settings>about" . It shows only (power on + volume down) screen.
Thanks for the time, any hint would be appriciated.
Thanks,
Nebojsa
Click to expand...
Click to collapse
Your device is bricked.
You might be able to save it if you can still get into USB host mode - Device off, hold down the volume down button and camera button together and power on the device, keep holding down the volume down and camera button until you see a screen with a phone and a laptop.
If you can get into USB host mode then you can try and flash the device using the goldcard/ Y cable method. You have to flash a stock/shipped rom that is specific to your device carrier with the Y cable.
Just follow the tutorial here:
http://forum.xda-developers.com/showthread.php?t=1597837

xdrc45 said:
Your device is bricked.
You might be able to save it if you can still get into USB host mode - Device off, hold down the volume down button and camera button together and power on the device, keep holding down the volume down and camera button until you see a screen with a phone and a laptop.
If you can get into USB host mode then you can try and flash the device using the goldcard/ Y cable method. You have to flash a stock/shipped rom that is specific to your device carrier with the Y cable.
Just follow the tutorial here:
http://forum.xda-developers.com/showthread.php?t=1597837
Click to expand...
Click to collapse
Thank you.. I will try that too. I edited my previous post. The phone start to work normally. I still can't access my camera, and i will try to replace Storage Card manually. I have a bit different menu now...so i assume Custom ROM install was successful. I'm doing all this to repair my "HTC white boot screen stuck problem". That ussally accure when battery reach low levels, so maybe it is battery problem aswell.
I will see if it will happen again when new ROM is installed.
Thank you for your time and help.
Regards, Nebojsa

Related

[SOLVED] Touch HD is dead???

Hi all!
first of all sorry for my Egnlish
I tried to perform task29 on my HD and get an error "Invalid vender ID", in some guides i read that in this case I should use a stock .nbh files... I tried the .hbn file from HSPL thread from one of restore_stock_spl* zip files. task29 was performed normally. When I turn on device I can see the clear smart mobility screen only with "smart mobility" words in center. bootloader now showing me 1.54 Olinex version. Before task29 this version was 1.56.
And from this moment I can't do anything with device: I can't flash any rom or radio. When using RUU after three-colour screen device shows me a progres indicator which suspends on 0% and RUU progress is also 0%. after waiting some time RUU shows an "262 Update erorr". When I'm trying to flash ROM or radio from SD card I see the three-colour screen then grey screen "loading... No image file!!!" and then again the three-colour screen. It shows so fast that it looks like a screen blinking and almost impossible to read what is written on grey screen.
I have spend 3 days while looking for different files and flash packages, have read a guides and I'm at a loss.
Please helpme to make my HD work again!
sergey.ss said:
Hi all!
first of all sorry for my Egnlish
I tried to perform task29 on my HD and get an error "Invalid vender ID", in some guides i read that in this case I should use a stock .nbh files... I tried the .hbn file from HSPL thread from one of restore_stock_spl* zip files. task29 was performed normally. When I turn on device I can see the clear smart mobility screen only with "smart mobility" words in center. bootloader now showing me 1.54 Olinex version. Before task29 this version was 1.56.
And from this moment I can't do anything with device: I can't flash any rom or radio. When using RUU after three-colour screen device shows me a progres indicator which suspends on 0% and RUU progress is also 0%. after waiting some time RUU shows an "262 Update erorr". When I'm trying to flash ROM or radio from SD card I see the three-colour screen then grey screen "loading... No image file!!!" and then again the three-colour screen. It shows so fast that it looks like a screen blinking and almost impossible to read what is written on grey screen.
I have spend 3 days while looking for different files and flash packages, have read a guides and I'm at a loss.
Please helpme to make my HD work again!
Click to expand...
Click to collapse
Have you tried flashing stock rom which came with your device?
I have tried .nbh file from "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE.zip"
if it possible tell me what exactly should I download and how to use it, I'll try. I'll try everything you advise, because I didn't find solution myself and don't know what esle should I try. first of all where should I start? do I need to perform task29 correctly or do I need to restore HSPL to 1.56 version, or flash a stock rom?
* Dont connect your phone to your computer.
* Hold down the Volume down button and hit the power button.
* Your entering the tricolor boot screen and at the bottom the word "Serial".
* Now connect you phone to your computer with te USB cable the word serial disappear and now it says USB.
* Now you can normally flash/update your phone and please use hspl.
I had before a HTC Diamond. On that device I used to run "task29" until that command killed my device. Almost same as you, I could flash the device but I couldn't boot normally. My ROM memory probably got damaged for good so I had to replace the device with a new one. My suggestion to you: on a new device never use that command again and you will be fine.
iamjohno said:
* Dont connect your phone to your computer.
* Hold down the Volume down button and hit the power button.
* Your entering the tricolor boot screen and at the bottom the word "Serial".
* Now connect you phone to your computer with te USB cable the word serial disappear and now it says USB.
* Now you can normally flash/update your phone and please use hspl.
Click to expand...
Click to collapse
I tried this way. Progress is suspends on 0% and then I get an error "262 Update Error" in RUU What should I do first: change HSPL version or flash ROM/radio?
xdmcdmc said:
I had before a HTC Diamond. On that device I used to run "task29" until that command killed my device. Almost same as you, I could flash the device but I couldn't boot normally. My ROM memory probably got damaged for good so I had to replace the device with a new one. My suggestion to you: on a new device never use that command again and you will be fine.
Click to expand...
Click to collapse
it's terrible, hope my devise still alive...
There is one detail I didn't mentioned... If download task29 package and just simply execute task29.exe (using .nbh from this package) progress on device goes forward to 4% and then "Invalid vender ID" error occurs... So I think I should use another .nbh file but which one?. Hope this checking of vender ID is not that 4% of progress and some actions with device memory really starts...
sergey.ss said:
I tried this way. Progress is suspends on 0% and then I get an error "262 Update Error" in RUU What should I do first: change HSPL version or flash ROM/radio?
it's terrible, hope my devise still alive...
There is one detail I didn't mentioned... If download task29 package and just simply execute task29.exe (using .nbh from this package) progress on device goes forward to 4% and then "Invalid vender ID" error occurs... So I think I should use another .nbh file but which one?. Hope this checking of vender ID is not that 4% of progress and some actions with device memory really starts...
Click to expand...
Click to collapse
Try using a radio nbh for blackstone.
The original package, contains nbh for the LEO
thanks all of you for replay but I still need a help very much.
there are ways that I have tried
1. flashing rom/radio from SD card
2. flashing rom/radio using RUU
3. task29 using different .nbh files
4. install/restore HSPL
In the first way always hapens same thig: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, then for a very short time (less than second) i see a grey screen and there is written: "loading... No image file!!!", then i see tricolor bootloader again.
I tried different rom/radio files (it was "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE" and other roms I flashed before and different versions of radio files from thread int this forum).
for the RUU using ways I always get two situations: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, connect the devise to PC, execute RUU/taks29/HSPL/Restore_SPL, then press next a few times, then i see the progress in RUU and on device screen and there is two endings:
1. progress goes up to 4% and devise making a soft reset, load the black smart mobility screen with no orange version characters on screen bottom, RUU shows "Invalid vender ID";
2. progress suspends on 0% and after some timeout RUU shows "Error [262] Update error" and now changes on device screen.
last what I have tried: execute task29 with last hd radio 1.17.25.09 file and got invalid vendor id error, then execute task29 with radio 1.09.25.14 file and got update error.
my be this holds some information: in my bootloader is written following
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
what should I do?
sergey.ss said:
thanks all of you for replay but I still need a help very much.
there are ways that I have tried
1. flashing rom/radio from SD card
2. flashing rom/radio using RUU
3. task29 using different .nbh files
4. install/restore HSPL
In the first way always hapens same thig: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, then for a very short time (less than second) i see a grey screen and there is written: "loading... No image file!!!", then i see tricolor bootloader again.
I tried different rom/radio files (it was "HTC Stock ROM_BLACKSTONE_1.14.401.3 (22273) WWE" and other roms I flashed before and different versions of radio files from thread int this forum).
for the RUU using ways I always get two situations: I turn off the device, turn it on, press volume down button, see tricolor bootloader screen, connect the devise to PC, execute RUU/taks29/HSPL/Restore_SPL, then press next a few times, then i see the progress in RUU and on device screen and there is two endings:
1. progress goes up to 4% and devise making a soft reset, load the black smart mobility screen with no orange version characters on screen bottom, RUU shows "Invalid vender ID";
2. progress suspends on 0% and after some timeout RUU shows "Error [262] Update error" and now changes on device screen.
last what I have tried: execute task29 with last hd radio 1.17.25.09 file and got invalid vendor id error, then execute task29 with radio 1.09.25.14 file and got update error.
my be this holds some information: in my bootloader is written following
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
what should I do?
Click to expand...
Click to collapse
Hmmm... I want to know, what .nbh file did you include in the task29 folder you have? Remember, you must to copy a radio ROM to your task29 folder and name it as RUU_signed.nbh, don't copy an OS ROM to task29 as this will give problem.
From the information above, seems you had restore to original SPL? Try flash HSPL or USPL. If you have any problem flashing, you can ask in this thread http://forum.xda-developers.com/showthread.php?t=505377
Good luck, my friend. Cheers.
Agree with philrom: you are an the stock SPL. So, flash HSPL, then you should be fine.
Has this been resolved?
Fallen Spartan said:
Has this been resolved?
Click to expand...
Click to collapse
Yes. Sorry I forgot to post the ending of this story...
I didn't understood about flashing HSPL in formated device... I was really tired of using different ways and flashing different roms... I just took my device to a not official service center (there is no Touch HD for my country). There guys said me that I need to flash a stock rom of my HD birthplace country. They found out that it was shipped from Arab Emirates, than they found a required ROM and flash it. It cost me 50$. Now I'm using my HD as usual.
Thank for the replays!!!
Glad you got it resolved
Thread closed

[Q] HTC Touch Diamond 2, not flashing

Dear Honorable Seniors, I am so obsessed to get some troubles with my htc (Touch Diamond 2).
I want to get rid off from my ROM that is already available on it (I dont how to find it is official or cooked and which is that version or name). I try to download many cooked ROMs to flash but tried two:
1-energy
2-mozart
but everytime flashing process stopped at 0% percent and after 6-7mint it display a window for recovery. I do restart my system and got the prior windows version, no flashing at all.
I thought there may be Hard-SPL issue (although I dont know what is it). I download its compatible version and try to flash Hard-SPL it also stuck at 0% and not moving upwards.
Help will be appreciated in their respect.
Sorry if my english not comprehendable I am not english speaking person.
regards,
Muqaddas Shahzad
[email protected]
+923222000048
1. Install HSPL. Follow instructions in the thread.
2. Install custom ROM.
You cannot install a ROM until you have installed HSPL first.
I think Muqaddas has already tried HSPL as he described in the post, but the progress stuck @ 0%.
Muqaddas, may be you can try below:
- Disable antivirus software, temporarily, on your PC
- Do HSPL (1.83 and update to 2.51)
- Use Advance ROM Update Utility to do a Task 29.
- Upgrade to latest Radio ROM, if not latest.
- Flash the ROM you wanted.
Hope this will help you .
Thanks.
dear prabhat thank to reply me dear:
1-during Hard spl I found my version is already about 2.16.415.3 and the version I got from Hard-spl link (your given) is showing 1.83.OliNex, yet I tried with this but again stuck at 0% (error code---262)......Can yoy please tell me how Can I check That my cell is already did hard-spl on it-----and how to know it is CID-Unlocked...............
2-by using Advance ROM Update utility, it also not being flashed and giving the same error 0% (code-262)
may this because of my PC operating system which is Windows 7?
but I have flashed HTC Touch Diamond in the same system.....
please help me, my already OS disturbing me alot.
i-windows (send-don't error)
muqaddas_dunyatv said:
please help me, my already OS disturbing me alot.
i-windows (send-don't error)
Click to expand...
Click to collapse
WIN7 could be your issue, it is best to use XP. Also it is important to install the enablenewrapi.cab
You can check your SPL level by entering bootloader mode (holding Volume Down as device reboots until you get to the tri-colored screen)to verify that your SPL: version has "Olinex" as a suffix.
How to flash?
RUU.exe method;
1. Download enablenewrapi.cab, copy to your device with ActiveSync (WMDC) and execute the cab.
2. Download Topaz_CustomRUU_v1.1.zip and both the 1.83 and 2.51 HSPL files.
3. Place the CustomRUU.exe and the RUU_Signed.nbh file from the 1.83 version into the same folder on your PC.
4. With your device sync'd, run the CustomRUU.exe and follow the prompts on your PC.
5. If successful, the progress bar will go to 100% and you can enter bootloader mode (holding Volume Down as device reboots until you get to the tri-colored screen)to verify that your SPL: version has "Olinex" as a sufffix.
If so, you've successfully flashed HSPL.
Repeat steps 3-5 for 2.51
If unsuccessful....
SD Card Method;
1. Rename the RUU_Signed.nbh to TOPAIMG.nbh and place on the root of your FAT32 formatted SD card.
2. Enter bootloader mode and it should initiate the flash. You may get an error of "No Image Found" or you get progress bar stuck at 0%. This would be a failed flash, just soft reset and you'll be back to stock.
If still unsuccessful....
Try the HardSPL_V5_00R5_183HSPL.zip
my respectable serniors please help me out, I tried to change the PC which has Windows XP, and followed all the procedures you all honored but still stock on 0%.....
dear I try to flash PHOTON ROM through storage card by renaming it and placing it into the root of SD card but not being flashed................
please help
HI Muqaddas,
The issue seems to be somewhere in HSPL and the device is not ready for any custom ROM yet. I dont think PC OS has anything to do here unless the "Antivirus S/W is disabled".
Once you device is CID unlocked you should able to install any ROM .
But as you are telling you can see "1.83.OliNex" in the Bootloader... so Can you try to update that to 2.51 and see if that work?
Also try searching the "error code---262" in the HSPL thread, whihc may give you some idea...
EDIT:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
As you said you can see the OliNex in bootloader your device is CID unlocked.
Can you try below and see if that work:
1) Upgrade your HSPL to 2.51.
2) Start Windows Mobile Device Center
3) Start your device in TriColor boot loader mode.
3) Connect you USB to PC and and make sure your device bootloader white screen say "USB"
4) Now start flashing from PC using RUU.
See if this work else try "SD Card Method" suggested by Bruce.
Hope this will help...
Thanks.
On Ur phone go to Settings-> Connections -> USB to PC & "uncheck" the option Enable faster data synchronization & then try ...worked for me
I am sorry to be desperate but after following all the precedures suggested in this place I am not successful...
I was hopefull that I might flash my TOPAZ after getting 512mb card and after many struggles I arranged it for flashing .....
but after bootloader it stuched at
loading.....
please help if someone can
Try restoring your bootloader to the stock, flash a Windows stock ROM, then come back with HSPL and custom ROM.
Hey, May be you can go to service center near to you and ask them to install new ROM so that they will install new ROM and may be try to unlock the phone if it is with them...
Once they install new ROM then I think you can continue HSPL here and have fun .
Thanks.
Dear Hamsn, Where I can get Windows stock ROM, Please any link or description......
You can get that from HTC website of your region.
Goto: http://www.htc.com/uk/selectcountry.aspx
Select your country -> Click Support -> Select your device and download the latest ROM update.
Of you can grab from here: http://shipped-roms.com/index.php?category=windows mobile&model=Topaz
(File: RUU_Topaz_S2_HTC_WWE_2.53.405.5_Radio_Signed_Topaz_61.44etc.25.35_4.49.25.91_Ship.exe)
Just sync your device in PC and run the above file and all should get updated .
Cheers!!!

[Q] Help Required regarding installing new ROM !!!

I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik
guitarguru31 said:
I am having Xperia X1 Black with factory installed Win Mo 6.1....so, now i wanted to try the Windows Mobile 6.5.3-Build- 29007. Can anyone help me with detailed procedure of installing new ROM on my X1.
I tried according to the procedure available in various post's. According to the procedure i need to first Hard SPL my phone. So, when i try doing that my progrees bar on the phone screen gets stuck at 0% and then i get a error that check the connection of the pc and phone.
In bootloader mode the configuration shown is as follows
KOVS110
SPL-0.78.0000
Micro P1-787
Micro P2-707
I even tried the direct SD card method in which i renamed the ROM file i.e RUU_signed.nbh to kovsimg.nbh...in this when i go to the bootloader mode, the tricolour screen shows with above mentioned specifications then after about few seconds another screen is displayed saying" LOADING..." and then gets stuck.
So, anybody can please help me with installing new ROM
Regards
Bhavik
Click to expand...
Click to collapse
You bootloader should show
Kovs110
SPL-0.78.OliNex
MicroP1-787
MicroP2-707
don't know if .0000 and OliNex is different
http://forum.xda-developers.com/showthread.php?t=431218
look here for download the good Hard SPL and then replace the 0.78 in it, HARD SPL with cable / computer (I never use SD CARD because it never works for me)
then you TASK29 (find it in the forum), then you can flash it =)

[Q] Help! - Bricked Incredible S, S-ON, unable to boot past HTC logo

Hi guys,
what I have:
Optus (AU) HTC Incredible S - it was running 2.3.3 fine, no hacks/root or anything has been done to it. [I've done a vol down + power button hboot thingy and it says S-ON]
what happened:
I connected the phone to a WIFI network to update my apps, it started updating many apps. mid-way through the updates, the phone became unresponsive and apparently hung, left it alone for a few hours, it remained hung.
I disconnected the power and pulled the battery.
The phone has since refused to boot past the HTC splash logo.
What I've tried:
I've tried rooting the phone with Revolutionary - however I can't complete the steps as I am unable to boot the phone.
I've tried Hboot with the [PG32IMG.zip] file - nothing seemed to change
I've tried usb fastboot with adb and fastboot - Signature verification failed [well, it is S-ON]
I've tried recovery - failed, gave me 3 arrows, 2 in a circular pattern and one straight, followed by a phone icon and a red triangle and ! mark
I've tried running the RUU.exe file for 2.3.3 optus, but it does not get past 'rebooting to bootloader'
Current situation:
I've spent around 6 hours trying to figure out what went wrong and make it work ... but nothing seems to work ... so guys ... i really could use some help ...
btw, I can't warranty it as I purchased the phone in Australia, but now am in Singapore ... I'll be returning to Australia in January though ...
All help and suggestions will be greatly appreciated ...
Thanks!
expiredyoghurt said:
Hi guys,
what I have:
Optus (AU) HTC Incredible S - it was running 2.3.3 fine, no hacks/root or anything has been done to it. [I've done a vol down + power button hboot thingy and it says S-ON]
what happened:
I connected the phone to a WIFI network to update my apps, it started updating many apps. mid-way through the updates, the phone became unresponsive and apparently hung, left it alone for a few hours, it remained hung.
I disconnected the power and pulled the battery.
The phone has since refused to boot past the HTC splash logo.
What I've tried:
I've tried rooting the phone with Revolutionary - however I can't complete the steps as I am unable to boot the phone.
I've tried Hboot with the [PG32IMG.zip] file - nothing seemed to change
I've tried usb fastboot with adb and fastboot - Signature verification failed [well, it is S-ON]
I've tried recovery - failed, gave me 3 arrows, 2 in a circular pattern and one straight, followed by a phone icon and a red triangle and ! mark
I've tried running the RUU.exe file for 2.3.3 optus, but it does not get past 'rebooting to bootloader'
Current situation:
I've spent around 6 hours trying to figure out what went wrong and make it work ... but nothing seems to work ... so guys ... i really could use some help ...
btw, I can't warranty it as I purchased the phone in Australia, but now am in Singapore ... I'll be returning to Australia in January though ...
All help and suggestions will be greatly appreciated ...
Thanks!
Click to expand...
Click to collapse
You better wait till january and claim the warranty!
hey buddy
well , the easy way to solve your problem is to download the stock rom for your device , and install it using the offical HTC exe ( the rom exe ) .
it will do it all and get your device like brand new .
hope this solve it .
If the above doesn't work send it to any htc repair center. You have to pay but whatever.
hassanhm said:
hey buddy
well , the easy way to solve your problem is to download the stock rom for your device , and install it using the offical HTC exe ( the rom exe ) .
it will do it all and get your device like brand new .
hope this solve it .
Click to expand...
Click to collapse
Hey hassanhm,
thanks for the reply. I've tried searching the HTC official website for the stock rom, however it is not available for download due to the fact that firmware upgrades are now over the air ..
i've downloaded the RUU rom by optus (RUU_Vivo_Gingerbread_S_Optus_AU_2.12.980.2_R_Radio _20.2803.30.085AU_3805.04.03.12_M_release_185028_s igned
http://www.filefactory.com/file/cfdd...028_signed.exe) found here - http://forum.xda-developers.com/showthread.php?t=1033922 - however it just gets stuck on the booting to bootloader step ...
if there a different stock rom exe file i should be using?
Thanks!
I'm a singaporean. Its uncommon to see this kinda stuff :/
looks like dead motherboard i saw thing like that already
I'm from Singapore. I had this issue, spent a day flashing and rebooting to try and fix it. Then I have up and just flashed an official ROM, I think any one will do, then sent it to HTC. It was still s-off but they didn't care. Took just 3 days and they sent it back, fixed and like brand new. I suggest you don't waste time and just sent to HTC. it will come back s-on but you can just root it again.
Hope this helps!
Sent from my HTC Incredible S using XDA App
There's one but when they put latest Hboot (1.16.0000)then it's harder to flash ROM than 1.13.0000. Hope you get your phone back and it's working
expiredyoghurt said:
Hi guys,
what I have:
Optus (AU) HTC Incredible S - it was running 2.3.3 fine, no hacks/root or anything has been done to it. [I've done a vol down + power button hboot thingy and it says S-ON]
what happened:
I connected the phone to a WIFI network to update my apps, it started updating many apps. mid-way through the updates, the phone became unresponsive and apparently hung, left it alone for a few hours, it remained hung.
I disconnected the power and pulled the battery.
The phone has since refused to boot past the HTC splash logo.
What I've tried:
I've tried rooting the phone with Revolutionary - however I can't complete the steps as I am unable to boot the phone.
I've tried Hboot with the [PG32IMG.zip] file - nothing seemed to change
I've tried usb fastboot with adb and fastboot - Signature verification failed [well, it is S-ON]
I've tried recovery - failed, gave me 3 arrows, 2 in a circular pattern and one straight, followed by a phone icon and a red triangle and ! mark
I've tried running the RUU.exe file for 2.3.3 optus, but it does not get past 'rebooting to bootloader'
Current situation:
I've spent around 6 hours trying to figure out what went wrong and make it work ... but nothing seems to work ... so guys ... i really could use some help ...
btw, I can't warranty it as I purchased the phone in Australia, but now am in Singapore ... I'll be returning to Australia in January though ...
All help and suggestions will be greatly appreciated ...
Thanks!
Click to expand...
Click to collapse
If you claim warranty : YOU LOSS A CHANCE TO HAVE BIG FUN I'm exactly on your situation (may be worse), but probably we feel different. I can only boot into fastboot and hboot ... LOL
expiredyoghurt said:
Hi guys,
what I have:
Optus (AU) HTC Incredible S - it was running 2.3.3 fine, no hacks/root or anything has been done to it. [I've done a vol down + power button hboot thingy and it says S-ON]
what happened:
I connected the phone to a WIFI network to update my apps, it started updating many apps. mid-way through the updates, the phone became unresponsive and apparently hung, left it alone for a few hours, it remained hung.
I disconnected the power and pulled the battery.
The phone has since refused to boot past the HTC splash logo.
Click to expand...
Click to collapse
You must be able to revive, since you did not do anything related to s-off, rooting etc. rooting, s-offing are for modding addict fellow
[/QUOTE]
What I've tried:
I've tried rooting the phone with Revolutionary - however I can't complete the steps as I am unable to boot the phone.
[/QUOTE]
Revolutionary only work on phone with NORMAL BOOTING (Android booting). If you did on fastboot then (I Think) you start create big trouble
I've tried Hboot with the [PG32IMG.zip] file - nothing seemed to change
Click to expand...
Click to collapse
This will only work for UPDATE, mean you must use higher version of ROM than in the phone (if you are s-on) -CMIIW-
I've tried usb fastboot with adb and fastboot - Signature verification failed [well, it is S-ON]
I've tried recovery - failed, gave me 3 arrows, 2 in a circular pattern and one straight, followed by a phone icon and a red triangle and ! mark
I've tried running the RUU.exe file for 2.3.3 optus, but it does not get past 'rebooting to bootloader'
Current situation:
I've spent around 6 hours trying to figure out what went wrong and make it work ... but nothing seems to work ... so guys ... i really could use some help ...
Click to expand...
Click to collapse
can you post your mainver : FYI, I could NOT resolve my vivo since my situation is worse than you, but probably my experience with unsuccesfull result will give different output ... who knows.
on fastboot (I'm sure You know how to do) fastboot getvar all (windows command) and post the output for our analysing together and help each other.
btw, I can't warranty it as I purchased the phone in Australia, but now am in Singapore ... I'll be returning to Australia in January though ...
All help and suggestions will be greatly appreciated ...
Thanks!
Click to expand...
Click to collapse
You will loss a big FUN on your life !!! by choosing easy way.
i have the same problem with a unit of incredible s. will not continue booting up past the htc logo.
Is this a software problem? cause im thinking maybe its the motherboard.
ice_pick88 said:
i have the same problem with a unit of incredible s. will not continue booting up past the htc logo.
Is this a software problem? cause im thinking maybe its the motherboard
Click to expand...
Click to collapse
.
what did you do before stuck. Can you boot into bootloader (?) are you S-ON or S-OFF (?) what is Hboot version do you have. To have bootloader state : press power and volume down button SIMULTANEOUSLY if within TEN MINUTES you do not have bootloader status you should stop and let us know here
Thanks for the reply. Its S-On, Hboot 1.13, I was simply browsing using the phone when it restarted and stuck with the htc logo.
ice_pick88 said:
Thanks for the reply. Its S-On, Hboot 1.13, I was simply browsing using the phone when it restarted and stuck with the htc logo.
Click to expand...
Click to collapse
I'm wondering. You probably did not enable fastboot option > setting > power > UNTHICK fastboot item.
On your today phone state you can not do it. Do you remember ? you enable fastboot option or not. Presumed you enable fastboot option then you can go to bootloader by pressing power and volume down buttons simultaneously > once you come into bootloader there is an option FACTORY RESET. If you see RED TRIANGLE. No other choice (AFAIK) you need to download the RUU of your phone and just run RUU ... all your personal user data will be wiped.
x1123 said:
I'm wondering. You probably did not enable fastboot option > setting > power > UNTHICK fastboot item.
On your today phone state you can not do it. Do you remember ? you enable fastboot option or not. Presumed you enable fastboot option then you can go to bootloader by pressing power and volume down buttons simultaneously > once you come into bootloader there is an option FACTORY RESET. If you see RED TRIANGLE. No other choice (AFAIK) you need to download the RUU of your phone and just run RUU ... all your personal user data will be wiped.
Click to expand...
Click to collapse
Thanks again for the reply. when i choose the factory reset the phone hangs but when i select recovery it goes to the red triangle logo. Where and how can i know whats RUU of my phone? Sorry im literally a noob.
3 days ago, i was having the same problen but i could solve it
Here what you can do:
1. Eject your sd card and insert another android phone. You can create a gold card over another android phone (Making gold card is completely independent from android version or phone model. Trust me.). You can search the forum, there are a lot of guides for making a gold card.
2. Boot into fastboot, plug your usb cable. Open a windows console, and send that command:
Fastboot getvar mainver
It will tell you your mainver.
3. Go here: http://forum.xda-developers.co m/showthread.php?t=1359555 .
In there, you can find original rom list. Choose one which has higher mainver than yours then download it. The thread also explains how to install the original rom.
Hth.
-R
programci_84 said:
3 days ago, i was having the same problen but i could solve it
Here what you can do:
1. Eject your sd card and insert another android phone. You can create a gold card over another android phone (Making gold card is completely independent from android version or phone model. Trust me.). You can search the forum, there are a lot of guides for making a gold card.
2. Boot into fastboot, plug your usb cable. Open a windows console, and send that command:
Fastboot getvar mainver
It will tell you your mainver.
3. Go here: http://forum.xda-developers.co m/showthread.php?t=1359555 .
In there, you can find original rom list. Choose one which has higher mainver than yours then download it. The thread also explains how to install the original rom.
Hth.
-R
Click to expand...
Click to collapse
Just for additional info. If you can not find another android/windows phone to get sdcard CID (you have only one phone and now in trouble). You can use any laptop with Built In card reader at PCI slot and NOT USB STORAGE if you were not have BOTH ... it's time to ask help your neighbour or your friends
Unlock bootloader through htcdev.com (phone doesn't have to boot normally to do this and it remains S-ON)
Flash clockwork recovery
Do arhd wipe
Flash any rom you want
flash the boot.img of that rom
there done
fallenwout said:
Unlock bootloader through htcdev.com (phone doesn't have to boot normally to do this and it remains S-ON)
Flash clockwork recovery
Do arhd wipe
Flash any rom you want
flash the boot.img of that rom
there done
Click to expand...
Click to collapse
Good day,
Thanks for the replies. Im having problem with this step. Im doing the unlocking the bootloader of the phone but when im in the process of inputting the cmd command "fastboot oem get_identifier_token" it gets me the " <waiting for device>
I have installed the latest htc sync version and updated all the drivers but it looks like my pc doesnt detect the incredible s.
Need suggestion guys.
Ill try the Gold card step later maybe it will work.
Thanks again.

[Q] HTC HD7 Stuck On Splash Screen

Hey guys, Google hasn't been as kind as ya'll are here, so I figured I'd give you a try. My mothers HTC HD7 failed to update via Zune a few months ago, and it has been stuck on the splash screen since (HTC with white background). So I took it from her since she now has an Android, and I'm looking to modify it. Upon booting into the hard reset mode, I do not get the actual recovery, I get a red, green, blue, and white screen. It reads as follows:
PD29110 SS-BC (4K) <------- In Red Rectangle
SPL-1.20.2250.0(111584)
MicroP(LED) 0x07
TOUCH S1(v2.A, #1625
SD SANDISK 15193MB Class0 <------- In Green Rectangle
Parition Info-v211v413
<------- In Blue Rectangle
USB <-------- In White Rectangle (When hooked up to my PC by USB cable. In this mode it installed drivers)
Note: In the middle of writing this, I saw it suggested here that this is a bootloader, so there should be a fix; http://forum.xda-developers.com/showthread.php?t=1161108
I think it's pretty clear what the question is here. How do I at the very least get this thing back to factory? Any help would be greatly appreciated. I'm no stranger to using programs to factory reset my phone, as I've soft bricked my LG Optimus One numerous and today it is running perfect on Cyanogenmod 9.
CodmasterRob said:
Hey guys, Google hasn't been as kind as ya'll are here, so I figured I'd give you a try. My mothers HTC HD7 failed to update via Zune a few months ago, and it has been stuck on the splash screen since (HTC with white background). So I took it from her since she now has an Android, and I'm looking to modify it. Upon booting into the hard reset mode, I do not get the actual recovery, I get a red, green, blue, and white screen. It reads as follows:
PD29110 SS-BC (4K) <------- In Red Rectangle
SPL-1.20.2250.0(111584)
MicroP(LED) 0x07
TOUCH S1(v2.A, #1625
SD SANDISK 15193MB Class0 <------- In Green Rectangle
Parition Info-v211v413
<------- In Blue Rectangle
USB <-------- In White Rectangle (When hooked up to my PC by USB cable. In this mode it installed drivers)
Note: In the middle of writing this, I saw it suggested here that this is a bootloader, so there should be a fix; http://forum.xda-developers.com/showthread.php?t=1161108
I think it's pretty clear what the question is here. How do I at the very least get this thing back to factory? Any help would be greatly appreciated. I'm no stranger to using programs to factory reset my phone, as I've soft bricked my LG Optimus One numerous and today it is running perfect on Cyanogenmod 9.
Click to expand...
Click to collapse
That is the bootloader screen indeed.
The good thing is that your bootloader isn't bricked or damaged.
More than likely during the update process the rom image was wiped or corrupted.
Try this first, download a stock/shipped specific rom for your device. Unzip all the contents (use a program like 7zip) to a new folder on your desktop.
Enter your device into bootloader mode and connect the device to your PC via USB cable. Device will change from "Serial" to "USB" click on the RUUwrapper (Rom Update Utility wrapper) in the folder and follow the prompts on the screen. That's it, should work and boot up.
I would recommend a stock/shipped rom that has a SPL of 3.xxx or under... That way if you want to install a custom rom your SPL doesn't have to be downgraded. To install a custom rom your SPL has to 3.xxx or lower, then you have to install RSPL/HSPL and the you can flash a custom rom of your choice.
If flashing the stock/shipped rom through bootloadet doesn't work then you'll need to use the goldcard/ Y cable method to flash the stock/shipped rom and then you can still install a custom rom. permitting your SPL is at or under 3.xxx
Here's a link to the stock/shipped roms -
http://forum.xda-developers.com/wiki/HTC_HD7/Shipped_Roms
Here's Shadow's tutorial on downgrading SPL, flashing XSPL and installing roms. It has all the links you'll need for the roms, goldcard/ Y cable method and everything you'll need -
http://forum.xda-developers.com/showthread.php?t=1295068
If you have any questions or need any help... Just let me know!
Thank you sir, you are indeed awesome. I'm going to try this tomorrow. I'm guessing SPL is the equivalent of a base band for an Android? I'm not familiar with Windows, but if I've got the similarities down I could figure it out relatively easy.
Sent from my LG-P509
Okay... I'm looking at the ROMs, and I have no clue which one I need. The phone is phone T-Mobile, so I'm sure TMOUS is the first part, but I have no clue what exact ROM I need. Any one will do?
CodmasterRob said:
Okay... I'm looking at the ROMs, and I have no clue which one I need. The phone is phone T-Mobile, so I'm sure TMOUS is the first part, but I have no clue what exact ROM I need. Any one will do?
Click to expand...
Click to collapse
Pretty much any TMOUS rom will work. Use this one though -
http://www.filefactory.com/file/cc8...9.25a_22.45.50.21_Signed_SCHUBERT_RELEASE.exe
The SPL on this one is 3.1 so after you install it and get the device booted, you can go to Shadow's tutorial and download RSPL and install it, download HSPL and install it and then download and install a custom rom. RSPL/HSPL and the custom rom are installed while in bootloader mode.

Categories

Resources