Related
Anyone else have a broken power button from regular day to day use?
Mine started acting up like 2 weeks ago. I noticed I had to press the power button more than once to turn the screen off/on. As the days went by the presses increased til it eventually gave out entirely this weekend as I landed in Vegas. I had to get someone to call my phone so I can turn the screen on and download "no lock" to enable trackball wake. I've also been paranoid about not letting the battery die since I won't be able to turn the phone on.
Calling Google/HTC tomorrow.
Btw, this is my second nexus one. First one had dead pixels. I had this second one maybe a month before the power button gave up!
Bummer.. Thought this might be a weak point in the design. Thanks for the heads up on "no lock". Will use that when @ home.
I've read about it happening a couple of times
Oh my god I'm having the same problem. Thought my N1's power button is now getting harder and harder to press to turn the screen on and off.
I was so angry about that, but after sometimes I figured out that the problem is not from the button (the hardware), it's because of the software. I dont know exactly from what apps which caused this, uninstalled some apps (especially apps for root only - which I thought are the main causes), but sometimes the problem occurs.
*Im using MCR r13.
And for your poor N1's button, I think it's broken because when facing with that trouble, you tried to press too hard... Bless your N1!
(Sorry for my bad english!)
Not A Software Problem...
The issue you are having is indeed a hardware problem. Well for the OP it is. I had a Nexus that was in the same situation. You can tell its not a hardware problem because if you remove the battery and put battery back in, the phone wont power up unless you press the power button like 8 to 10 times. That my friend is a hardware situation.
I created a small fix for mine. I should have created a youtube video of it lol. What I did was removed the back cover and batter and inbetween the Power Button and The Phone itself youll see like a small crack or very small gap of space between the phone and button. I stuck some small very small thin piece of paper in that gap. This will raise the buttun away from the phone just a lil bit. Put the battery back in and back cover back on. And noticed my button working 100% again.
So long story short the button itself starts to not make contact with the switch on the mother board or somethin. My bootloader was unlocked so i never got HTC involved. If your on cyan lates rom you can set it to wake via trackball under settings.
In the end, I ended up selling that N1 on craigslist for loot for a HD2 and HD2 was gargage (out dated OS and 65k color max display at LCD) and ended up selling the HD2 and got another nexus.
PS - I did have one of them argyle clear body cases on it that fit the N1 very snug and tightly, and wonder if that had somethin to do with power button goin out since it was rubbing against it repeatily.
same story happend to me, with a regular daily usage. It really bummers me, i unlocked the bootloader too, so i cant send it to HTC.
And I can't sell it in this condition too, sux!
Anyone with the same problem that sent it to HTC?
My wife had her's for about a week before having issues with the power button. Got a replacement and haven't had issues yet.
I had the same problem as the OP. Had to push the button several times to get the phone to respond.
HTC swapped my original N1 with dust under the screen and then sent me one that eventually had the power button crap out.
My GF's Nexus One has had no issues at all and we bought around the same time. My current (third) N1 is now rooted so I'm crossing my fingers that I won't need to deal with HTC again.
I love both the N1 and Android, but from my experience, I'm shocked and disappointed with it's poor build quality.
hypersonicx said:
The issue you are having is indeed a hardware problem. Well for the OP it is. I had a Nexus that was in the same situation. You can tell its not a hardware problem because if you remove the battery and put battery back in, the phone wont power up unless you press the power button like 8 to 10 times. That my friend is a hardware situation.
I created a small fix for mine. I should have created a youtube video of it lol. What I did was removed the back cover and batter and inbetween the Power Button and The Phone itself youll see like a small crack or very small gap of space between the phone and button. I stuck some small very small thin piece of paper in that gap. This will raise the buttun away from the phone just a lil bit. Put the battery back in and back cover back on. And noticed my button working 100% again.
So long story short the button itself starts to not make contact with the switch on the mother board or somethin. My bootloader was unlocked so i never got HTC involved. If your on cyan lates rom you can set it to wake via trackball under settings.
In the end, I ended up selling that N1 on craigslist for loot for a HD2 and HD2 was gargage (out dated OS and 65k color max display at LCD) and ended up selling the HD2 and got another nexus.
PS - I did have one of them argyle clear body cases on it that fit the N1 very snug and tightly, and wonder if that had somethin to do with power button goin out since it was rubbing against it repeatily.
Click to expand...
Click to collapse
Wow... I'm shaking my head at this. You'd think HTC would have thought about this some more...
Crossing my fingers, cuz my power button still "works the first time, most of the time"..
Yea I gave myself a good month of testing this phone before even considering rooting and I'm glad I did.
My first unit was rooted and it was hell to get htc to support my fix over a dead pixel so naturally on my second phone I avoided rooting.
With the build quality on these phones (unfortunately) I would recommend NOT rooting for a good month or so to make sure you don't need warranty support.
I've ended up doing the repair option because I can never justify a $529 hold. Will get a ****ty flip phone loaner from Tmobile for the time being.
sorry to hear your issues but thank you for pointing out that app "no lock". I've been waiting for something like this! Now I can wake my Nexus with the volume button rather than the power button(wear and tear) or the trackball(it gets dirty from touching too much so I never do).
Have any app can replace power button?
I got a ****ty samsung flip phone loaner from tmobile. Ironically, I feel the call quality on these old phones are better than all the smart phones i've owned lol
Will this issue eventually happen to every one? That would be horrible..
Eclair~ said:
Will this issue eventually happen to every one? That would be horrible..
Click to expand...
Click to collapse
I guess that all depends on how much people "baby" their phones. Then again, we all die eventually.. same with technology.
ChillRays said:
I guess that all depends on how much people "baby" their phones. Then again, we all die eventually.. same with technology.
Click to expand...
Click to collapse
Phone was never dropped and was in one of those gel cases. I use my phone heavily but no more than I've used any of my other phones. That power button is definitely not made for heavy use. I'd hope froyo has a trackball awake feature because from what I read on the interweb this problem is definitely not exclusive to a select few people.
That really blows about the power button. I've heard of that alot now and feared it as well. I'd never heard of the "nolock" program so I'm really glad you mentioned it. Downloaded it and fired it up. Talk about a sweet program, I can't believe it flies to far under the radar. I'm not rooted so it's definately a great program as I wanted trackball wake. Plus you can create a widget on the desktop so you can toggle it off. Sorry about your phone but thanks for the program. I hope you get your phone fixed soon.
Wow a 1 day turn around. My phone should be back here tomorrow in the morning. Seems like HTC customer care is improving?
uansari1 said:
Wow... I'm shaking my head at this. You'd think HTC would have thought about this some more...
Crossing my fingers, cuz my power button still "works the first time, most of the time"..
Click to expand...
Click to collapse
Eh TBH I've heard of iphones with the same problem. Manufacturing tolerances in any product inevitably produce a few faulty units...that's what the warranty is for.
Just be glad your N1 will never decide that its automatic backup is now encrypted and password-protected and that you can't use your phone until you figure out what the password you never set is (happened on my brother's iphone 3G)
hypersonicx said:
I created a small fix for mine. I should have created a youtube video of it lol. What I did was removed the back cover and batter and inbetween the Power Button and The Phone itself youll see like a small crack or very small gap of space between the phone and button. I stuck some small very small thin piece of paper in that gap. This will raise the buttun away from the phone just a lil bit. Put the battery back in and back cover back on. And noticed my button working 100% again.
Click to expand...
Click to collapse
Can you please explain how to remove the power button? Can it be removed alone or you have to remove all the screws and body of the phones?
I can turn on the milestone with the power button but when the OS has booted up it becomes unresponsive, if i keep pressing it it sometimes goes to the power off menu but besides from that it does not work
also i can no longer boot into the bootloader but recovery still works, the last rom i installed was the cronos rom with the included kernel, i used this rom for most of the day and it was fine untill i got home
hopefully someone can help
so...no one has any idea what i can do?
Hi silvacrest, I know this is a very old post (in Internet years), but have you (or somebody else) by any chance found a fix for the problem you described? My Milestone running CM7.2RC1 just started to present those same symptoms.
Thanks!
I have the same problem, started an hour ago, i don't know why, someone please help!
Try taking the battery, SD, and SIM out and using a can of compressed air (NOT an air compressor machine, those pull tons of moisture out of the air and can cause serious damage to your phone) on every nook and cranny of the device. Around and in the headphone port, around the power button, everywhere inside the battery compartment, etc. You'd be amazed at what problems dust can cause.
Thank you for the advice, I'll try that and keep you updated!
Sent from my Milestone using xda premium
Don't recommend this.
You will break the button for good and you'll need to open your phone, well if think you already need to do that.
The milestone button is composed of a thin foil glued to a metallic case, the glue gets old and the adherence with time will decrease and the foil will get dislocated from it's location. This is why your buttons won't work anymore.
If you use compressed air will probably break the button. I have fixed mine by putting a little thin foil of duct tape after I put the foil button in place.
Good luck.
There are more than enough videos out there that shows how to open the milestone.
Hi i2gh0st, in my case, the milestone now sometimes acts as if the power button was pressed, long or short press, waking up the device, displaying the menu or even boot when the phone is off.
You think this behavior could correspond to the foil problem you described?
I don't think so, the button should not work at all, unless it got stuck on press mode. Anything is possible its a ****y button if you look at it from an engineering way.
When I assembled my phone last time I noticed the volume up didn't work, so I opened it again and I found the foil glued to another place instead of its location. So everything started to make sense why buttons break down.
Sorry if I don't really make myself understood, I'm not that good at technical English.
Oky, can't find any relevant video or picture to show you, so I'll open my phone again in week-end after my exam and make a video or some pictures. Just wait a little
power button: Too recessed and flat, to the point where I now have to use my fingernail to power on the device.
volume button: Flimsy to the point where I can literally slide it up and down. I can also hear it jingle when the device vibrates.
Backcover Flimsy, moves around too much and is never tightly secured.
hardware: When I unplug my device from the charger and the screen is getting ready to time out, it flashes green, then times out... (this looks like it's going to create bigger issues down the road)
Power button: 1 in 20 HD7's I have exhibited the behavior you mention. It went away however. I would advise against using your fingernails if at all possible.
Volume Button: Again, 1 in 20 have this, and unfortunately it's the one I carry around. Two other HD7's I personally used did not have this.
I'd try to get it replaced if I were you.
I'm 2 for 2 on the first two annoyances (power and volume button).
I'm getting it replaced again (for the third time) tomorrow morning. I've also noticed these problems with the store models at various T-Mobile stores.
If I have the same problem with my third device, I'm returning it and getting my refund. Omnia 7, here I come.
Hmmm... I don't care much for the power button placement, but I haven't seen any of the other things you mentioned.
jimbonics said:
Power button: 1 in 20 HD7's I have exhibited the behavior you mention. It went away however. I would advise against using your fingernails if at all possible.
Volume Button: Again, 1 in 20 have this, and unfortunately it's the one I carry around. Two other HD7's I personally used did not have this.
I'd try to get it replaced if I were you.
Click to expand...
Click to collapse
regarding issue #1, how did the problem go away? did some mechanism inside shift causing the power button to pop out more? just wondering?
i also have the loose battery cover. very annoying.
also about the screen... havent seen this mentioned before. i have a slight gap at the left and right edges of the screen where it meets the chrome-ish border. its pretty easy for particles to get stuck in there. compared to the hd2, this gap is pretty noticeable.
I thought I was the only one with these issues lol, figured the recessed power button was just a design oversight
@jimbonics: just wondering, but why do you advise against using your fingernail?
Sent from my T-Mobile G2 using XDA App
jimbonics said:
Power button: 1 in 20 HD7
Volume Button: Again, 1 in 20 have this
Click to expand...
Click to collapse
Seriously? I checked a batch of HD7 in malaysia, and exceptionally, all of them had this issue. You're just so lucky you dont have it
daaango said:
why do you advise against using your fingernail?
Click to expand...
Click to collapse
Maybe because of this ?
Thanks Shu and daaango.
I knew I wasn't crazy in thinking this was an issue only I was experiencing.
I've also read several phone reviews, and a lot of the reviewers mentioned about the power button being recessed and stating frustration waking up the device.
I don't know how HTC can fluff up something so important. I mean, what good is a product if you can't power it on; wake it up? One would think they would put emphasis on having a solid foundation on the power button.
Melcali: Yeah, on one phone the power button managed to become flushed, to the point the user had to use their fingernail (even though i found it easy to turn on with the flat of my finger, almost like it was capacitive). However, next day it had 'popped out' a bit and had become less recessed and hasn't been a problem for him since.
daango: In addition to what Shu posted, using your fingernail is likely going to cause you to press the button in harder than it needs to be, which would likely cause the button to be crammed in more and more over time. If it can't be prevented, it can't, I'm just advising against it.
I've got two unopened spares. I'm going to crack them open and see if the volume button jiggles.
Ah, thanks shu and jimbonics for explaining that
Honestly, I don't think it can be helped. Maybe my fingers are too round or something, but using my fingernail seems like the only option right now. I might try adding layers of tape on the button so its easier to press but idk yet... it might take away from the aesthetics
Sent from my T-Mobile G2 using XDA App
All five units I've come across so far -- my defective original (corrupted memory), my current one, a second defective one (also corrupted memory), its replacement, and an in-store demo phone -- have the same issues:
Recessed power button
Very difficult to press camera button (basically useless)
Loose volume rocker (the case opening is about 0.8 mm too long for the rocker, so it moves around)
Imperfect battery cover fit (the plastic cover flexes from the opening process, so usually doesn't fit perfectly)
Weak screen support in bottom-right (press a bit on the search key and you'll see waves on the LCD)
On the two that I've had long enough to use, the clear coat on the kickstand is flaking off, and the Windows Phone logo, which was barely visible to begin with, has almost completely faded away on one of them.
Kind of sad that HTC screwed up so badly given that the HD7 is a barely-modified HD2, which was among the best-built phones on the market.
amb9800 said:
All five units I've come across so far -- my defective original (corrupted memory), my current one, a second defective one (also corrupted memory), its replacement, and an in-store demo phone -- have the same issues:
Recessed power button
Very difficult to press camera button (basically useless)
Loose volume rocker (the case opening is about 0.8 mm too long for the rocker, so it moves around)
Imperfect battery cover fit (the plastic cover flexes from the opening process, so usually doesn't fit perfectly)
Weak screen support in bottom-right (press a bit on the search key and you'll see waves on the LCD)
On the two that I've had long enough to use, the clear coat on the kickstand is flaking off, and the Windows Phone logo, which was barely visible to begin with, has almost completely faded away on one of them.
Kind of sad that HTC screwed up so badly given that the HD7 is a barely-modified HD2, which was among the best-built phones on the market.
Click to expand...
Click to collapse
wow, you have had a lot of problems. I'm still on my original hd7 since second week of november.
1. power button is slightly recessed, but no problems pushing it with my finger (not nail)
2. camera button does have some orange on it, but it functions properly.
3. volume buttons work fine, maybe a little slide to the rocker, but doesn't effect controls
4. no flaking of clearcoat, no wp7 logo coming off, no lcd discoloration no matter how hard I press on the search or back buttons.
5. Back cover fits properly. I haven't had much reason to pull it off after initial placement of sim card, thanks to phone not constantly freezing. There is a slight gap where the back cover meets the smaller cover.
What are you subjecting your phones to???
I agree the hd7 build quality might not be iphone, but it's holding up well for me. It's not like we have a lot of choices on t-mobile, the dvp has way more problems at this point.
amb9800 speaks the truth. I went through 3 different units that had defects to varying degrees. I had similar issues with the EVO as well. HTC are notorious for shoddy craftsmanship.
I have the same problems they started AFTER my 30 days .. So i havent tryed to go and change at my local T-Mobile!! Is there any loop in the contract or something that would let me change it for anither phone and pay difference/get a refund xD
have the same problems as the op
Home button just stopped working. Its happened a couple of times before, but it comes back after a day or so. Is this a common problem on the ds7? I didn't find any mention of this anywhere.
If honeycomb have the button bar at the bottom when its released, this wont be a problem.
vtinmanv said:
Home button just stopped working. Its happened a couple of times before, but it comes back after a day or so. Is this a common problem on the ds7? I didn't find any mention of this anywhere.
If honeycomb have the button bar at the bottom when its released, this wont be a problem.
Click to expand...
Click to collapse
I have never seen this problem, and have not heard about it before. Have you try to search for an app that remap button?
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
vtinmanv said:
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
Click to expand...
Click to collapse
I'm using this case, it fit perfect because its made for the ds7. I don't know if its anti - static or not, but it close into a book like style. I'm not affiliated with this eBay seller, just using it for reference.
http://www.ebay.com/itm/NEW-T-MOBIL...580194?pt=PDA_Accessories&hash=item23128548e2
otnos said:
I'm using this case, it fit perfect because its made for the ds7. I don't know if its anti - static or not, but it close into a book like style. I'm not affiliated with this eBay seller, just using it for reference.
Click to expand...
Click to collapse
I was eyeing this case too. But since the button is already broke, no point in getting a case now. Hopefully, this will be a non-issue once I install honeycomb since it'll have the action bar. Assuming it works just like 3.1 on a galaxy tab 10.1. In fact, I might be looking for a way to disable the hardware buttons.
vtinmanv said:
The home button is working again after I left it alone overnight and restarted it in the morning.
After thinking about it a bit, it seems that every time the home button stops working, it's after I take the Streak out in my jacket pocket. I think this may be a problem with static electricity, the screen have been rubbing against my jacket so it's always spotless when I take it out of my pocket. But why is only the home button affected?
Can anyone recommend a good anti-static case for the Streak 7?
EDIT: Spoke too soon, it seems on and off. But it's definitely static that caused this.
Click to expand...
Click to collapse
I've had my screen itself be poor or nutty responsive behaviour, but I can almost always turn the screen off and back on and it fixes it. Usually happens when I pull it out of my pocket and it's either still partly in my pocket or my fingers are on the screen while turning it on. Seems all capacitive devices do a screen calibration on screen-on and it hoses it when it's being touched.
Hey, recently I bought a Sony Xperia Z (C6603) off ebay. The phone is working fine so far, except for one thing:
The power button is VERY sensitive. If I only swipe over it with my finger, it treats this already like a press.
Comparing it to my other C6603 (I want to give on of them to my parents) with a working power button,
I can see that the working button sticks a tiny bit more far out than the overly-sensitive one. Also, the sensitive one doesn't give that typical "click"-feedback when pressing it.
Not only do I fear that this would accidentially turn on the screen whilst being in my pocket, but also it's a bit irritating while actually using the phone (initially I thought that the LCD was defect until I realized that it's only flickering because my finger touched the button lightly).
Has anyone else experienced this and/or knows a solution? I guess since the device is waterproof opening it (and closing it after) is bit more of an effort and is thus not too advisable. But who knows.
With the case on it's a bit better but still an issue.
tl;dr: Power button is VERY sensitive, is there any easy fix?
Also, is there any app that could tell me how often the screen got turned on during the phone was in my pocket? Just to know how much this is an issue.
Thanks in advance!