[Q] Big time help needed - Galaxy Tab 8.9 General

I think I may have done it this time. I was trying to root my galaxy tab ATT SGH-I957 through Odin. I flashed AOSP through Odin, it showed it flashed successfully. So I began to boot my tablet up in Recovery Mode. I got the following Message Under ODIN MODE: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I then connect my tablet into my laptop, and try to connect it to Kies only to find that Kies cannot discovery my tablet, as it just continues to show that kies is trying to connect the device.
I then try to get back into Odin3 v1.83 to see if I can flash the stock recovery.rar and get a red FAIL with the Following Message:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1
So- I am at a loss.
I honestly cannot give any further details as to where I goofed- as I did this while watching NLDS Game 5 as a Cardinals fan.. Too much excitement I guess.

Still stuck.. have I royally screwed things up?
jhgebel said:
I think I may have done it this time. I was trying to root my galaxy tab ATT SGH-I957 through Odin. I flashed AOSP through Odin, it showed it flashed successfully. So I began to boot my tablet up in Recovery Mode. I got the following Message Under ODIN MODE: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I then connect my tablet into my laptop, and try to connect it to Kies only to find that Kies cannot discovery my tablet, as it just continues to show that kies is trying to connect the device.
I then try to get back into Odin3 v1.83 to see if I can flash the stock recovery.rar and get a red FAIL with the Following Message:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1
So- I am at a loss.
I honestly cannot give any further details as to where I goofed- as I did this while watching NLDS Game 5 as a Cardinals fan.. Too much excitement I guess.
Click to expand...
Click to collapse

You didn't by chance flash a ROM for the 7300?
If so, I think you are screwed, as the hardware is different as well as the partitions.
go back and check the filename for the .tar you flashed.
Sent from my SAMSUNG-SGH-I957 using XDA Premium HD app

Flash the stock rom through odin and you'll probably be ok. You can find the stock rom on sammobile. Make sure you get the right one for your device.
Sent from my SAMSUNG-SGH-I957 using xda app-developers app

jhgebel said:
I think I may have done it this time. I was trying to root my galaxy tab ATT SGH-I957 through Odin. I flashed AOSP through Odin, it showed it flashed successfully. So I began to boot my tablet up in Recovery Mode. I got the following Message Under ODIN MODE: "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I then connect my tablet into my laptop, and try to connect it to Kies only to find that Kies cannot discovery my tablet, as it just continues to show that kies is trying to connect the device.
I then try to get back into Odin3 v1.83 to see if I can flash the stock recovery.rar and get a red FAIL with the Following Message:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1
So- I am at a loss.
I honestly cannot give any further details as to where I goofed- as I did this while watching NLDS Game 5 as a Cardinals fan.. Too much excitement I guess.
Click to expand...
Click to collapse
Turn off .. firewall, anvir, run odin as administrator
Sent from my GT-P7300 using xda premium

Related

[Q] Stuck at "Get PIT for Mapping" everytime

hello all! so i hope that wans't posted before,
Here is the thing , earlier today i tried to flash to JM7 but odin got stuck for 2 hours so i unplugged the usb. Since then i have been trying to flash jm,1 jm5, or jm6 but i can't get past the "get PIT for Mapping".,
Since earlier i also can't make the phone to boot, black screen all the way , the only thing i can do is get in download mode, i can't even access recovery mode.
did it ever happen to anyone?
Yeh happened a few times. Are you using the right pit file? Also set odin to win xp compatibility mode with admin access. Unplug all usb except mouse and kb and try again
Worst case find yaself a xp box and do it there.
Sent from my GT-I9000 using Tapatalk
d.fx said:
hello all! so i hope that wans't posted before,
Here is the thing , earlier today i tried to flash to JM7 but odin got stuck for 2 hours so i unplugged the usb. Since then i have been trying to flash jm,1 jm5, or jm6 but i can't get past the "get PIT for Mapping".,
Since earlier i also can't make the phone to boot, black screen all the way , the only thing i can do is get in download mode, i can't even access recovery mode.
did it ever happen to anyone?
Click to expand...
Click to collapse
Did you follow exactly the instruction given? You may read the link below
http://forum.xda-developers.com/showpost.php?p=7940762&postcount=1
It did happen to me once , i was on windows 7 , i installed xp on my macbook and since then all my flash went great.
Sent from my GT-I9000 using XDA App
d.fx said:
hello all! so i hope that wans't posted before,
Here is the thing , earlier today i tried to flash to JM7 but odin got stuck for 2 hours so i unplugged the usb. Since then i have been trying to flash jm,1 jm5, or jm6 but i can't get past the "get PIT for Mapping".,
Since earlier i also can't make the phone to boot, black screen all the way , the only thing i can do is get in download mode, i can't even access recovery mode.
did it ever happen to anyone?
Click to expand...
Click to collapse
Yeah I know..I'm bringing a thread back from the dead. But I'm desperate right now.
I'm having the same issue. So I rooted my phone awhile ago and was using the Paragon RC4 ROM, I upgraded it to RC6 and everything worked fine, but I decided to start from a clean slate and use ODIN3 to go back to stock and start from scratch (with a full battery cause when I first flashed I was apparently only at 98% battery). So I started ODIN3 and put the phone into download mode. ODIN picked the phone up right away and I hit Start. ODIN's status says:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
And it sits at 'Get PIT for mapping..'.
There's a small blue status bar on the phone and it just sits at about 1/4".
I did a bad thing and yanked the battery and now the phone will only go into Download mode and ODIN still just sits at 'Get PIT for mapping..'. I can't get into recovery mode, can't even get a splash screen. I can't post in the [STOCK ROM\ Odin3 thread cause I'm a new member. So I'm stuck...anyone know what I can do to fix this?
Where is the pit file you are using .
jje
I have the same problem. Phone get's stuck at that point. I don't know what to do. I am using win 7 64 bit. Does anyone have an idea.
razyell said:
I have the same problem. Phone get's stuck at that point. I don't know what to do. I am using win 7 64 bit. Does anyone have an idea.
Click to expand...
Click to collapse
Put pit file on the desktop in a folder with the zipped files makes location easy .
Are you using the correct pit file are you loading it in PIT
jje
done.
JJEgan said:
Put pit file on the desktop in a folder with the zipped files makes location easy .
Are you using the correct pit file are you loading it in PIT
jje
Click to expand...
Click to collapse
I've managed to solve it. It wasn't the pit file, it was my 64 bit Windows. After I emulated a virtual machine and installed windows xp 32 bit, it worked like a charm.
razyell said:
I've managed to solve it. It wasn't the pit file, it was my 64 bit Windows. After I emulated a virtual machine and installed windows xp 32 bit, it worked like a charm.
Click to expand...
Click to collapse
My i9003 gets stuck there. i tried to emulate but i get an error regarding the PDA. can u please let us know how u did it???
razyell said:
I've managed to solve it. It wasn't the pit file, it was my 64 bit Windows. After I emulated a virtual machine and installed windows xp 32 bit, it worked like a charm.
Click to expand...
Click to collapse
this is the error i get in the virtual pc in xp mode
i solved it by plugging the cord into another port and letting windows rediscover the phone
screwyluie said:
i solved it by plugging the cord into another port and letting windows rediscover the phone
Click to expand...
Click to collapse
Plus One to this solution. Thought I killed my phone.
screwyluie said:
i solved it by plugging the cord into another port and letting windows rediscover the phone
Click to expand...
Click to collapse
+1
soft brick
i got the same problem.
cant get it right. im on winxp 32 got the pit file from this thread and stock rom MDC from Sammobile site.
<ID:0/008> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720VPUAMDC_L720SPTAMDC_L720VPUAMDC_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Removed!!
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/008> Added!!
I don't know what happened, I switched from pc to laptop and tried the same thing with pit file, same error, but my phone is working now. No changes in the phone it's still in MDL and I have superuser app but it says binary not found. Can't install binary also...
Sent from my SPH-L710 using Tapatalk 2
SOLVED
http://forum.xda-developers.com/showthread.php?t=2298876
[solved] pit file not found error
Sent from my SPH-L710 using Tapatalk 2
same problem :/
n30nix said:
Yeah I know..I'm bringing a thread back from the dead. But I'm desperate right now.
I'm having the same issue. So I rooted my phone awhile ago and was using the Paragon RC4 ROM, I upgraded it to RC6 and everything worked fine, but I decided to start from a clean slate and use ODIN3 to go back to stock and start from scratch (with a full battery cause when I first flashed I was apparently only at 98% battery). So I started ODIN3 and put the phone into download mode. ODIN picked the phone up right away and I hit Start. ODIN's status says:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
And it sits at 'Get PIT for mapping..'.
There's a small blue status bar on the phone and it just sits at about 1/4".
I did a bad thing and yanked the battery and now the phone will only go into Download mode and ODIN still just sits at 'Get PIT for mapping..'. I can't get into recovery mode, can't even get a splash screen. I can't post in the [STOCK ROM\ Odin3 thread cause I'm a new member. So I'm stuck...anyone know what I can do to fix this?
Click to expand...
Click to collapse
same problem dud , i didnt find any solution so far ! :/
moody-mj said:
same problem dud , i didnt find any solution so far ! :/
Click to expand...
Click to collapse
Do you have a custom recovery or not?
Sent from my SPH-L720 using Tapatalk 4 Beta
thx for your fast replay...
pvinodnayak said:
Do you have a custom recovery or not?
Sent from my SPH-L720 using Tapatalk 4 Beta
Click to expand...
Click to collapse
first of all thanks for your fast reply
i've downloaded this firmware ( \N7100XXDLJ2 OXA FACTORY )
and tried it , didnt work
i work at samsung company in lebanon , and i have all the offical firmwares
i tried them , it wont work
in odin 3.04 it wont work , it quickly fails with out even starts ( re-partition operation failed )
and in odin 3.07 ( get pit for mapping ) and stucks on ( set partition )
i tried allot of different PIT files , and unticking ( re-partition ) nothing happend , and it only goes to download mode , or when i turned it on , it stucks on ( samsung galaxy note II ) plz help me

[Q] Stuck in Odin when flashing kernel

I was following the overcome guide and when i came to step 8/9 (flash overcome kernel) it didn't work, so then i chose the same pit which you use in a previous step and also the kernel and now it worked with the pit but not the kernel. i got stuck in download mode and tried to flash only kernel again but it didn't work not it got stuck on ConnectionSetup... or something like that. I think it couldn't find the device, i shut down odin and took out the micro-sd card which someone said could cause problems but it still didn't work. now i'm stuck at a screen like this: picture of phone .. ! .. picture of computer. I guess it means it can't connect to the computer. Anyone know what to do? I've tried searching the forums and tried some different stuff but haven't succeded.
Edit: Seems like i can use odin even though i don't get into the download mode, will update soon. Seems to work correctly, i'll give the flashing another try and i will make sure to cross the right boxes and so on.
Edit2: This time i checked that i had all the correct things crossed in Odin but when i try to flash the kernel it fails. what should i do? i come from gingerbread 2.3.3 (re-stocked) so it can't be the bootloader right?
Edit3: This is what i get when i try to flash the kernel:
<ID:0/036> Added!!
<ID:0/036> Odin v.3 engine (ID:36)..
<ID:0/036> File analysis..
<ID:0/036> SetupConnection..
<ID:0/036> Initialzation..
<ID:0/036> Get PIT for mapping..
<ID:0/036> Firmware update start..
<ID:0/036> ‹
<ID:0/036> NAND Write Start!!
<ID:0/036>
<ID:0/036> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Edit4: From my research it seems i have the same problem as people hade with the signed/locked bootloaders on froyo, however i'm running 2.3.3 and the thread specifically said not to use their patch so i have no idea of how to solve this. Help would be very appreciated.
Edit5: finally works, thanks to this: http://forum.xda-developers.com/showthread.php?t=1324052

Can't flash with Odin - Please help!

I have been trying to flash my Samsung Galaxy S i9000 for a week now with no success.
First off, it has a lot of problems connecting when I am in download mode. It has no problem at all when the phone is fully booted up, but Odin has a really hard time seeing it while the phone is in download mode. I have to restart the phone several times into download mode and pull the cable, etc until I can finally get Odin to see it.
Once I get Odin to finally see the phone in download mode I loaded the PIT and the PDA files from the tutorial for DarkyROM_10.2_Resurrection.
But when I hit start is just stops here:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
And will not go any further.
I originally rooted with one click, but I am afraid I might have messed that up. After I did the one click I was messing around with the phone and formatted the internal memory from the download screen. I even went back into one click to try to unroot, but it gives me an error message.
Did I mess up my phone? Is there any way to fix this?
have you ever succeeded in flashing with odin or first time?
have you closed all kies programs from task manager? (do you even have it installed?)
if you have win7, have you opened odin with right click menu->as administrator?
what ver. of odin do you use?
maybe the cable is faulty?
did you connect it directly to the comp or by some hub? (better connect directly)
guy7685,
No, I have never flashed before. This is the first time.
I tried running Odin as system admin, made no difference.
I do not have Kies installed.
I'm pretty sure the cable is good, it works fine for everything else including data transfer on my other phone, just not in download mode for this phone.
I've tried a few different versions. v1.30, v1.83, v1.85
When I tried in in v1.83 & v1.85 I get a fail, then this message:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Can't open the serial(COM) port.
<OSM> All threads completed. (succeed 0 / failed 1)
Any thoughts?
If you have another computer you can try it on, do that otherwise I think you need to install the drivers again. You can search for them or you can install them via kies. Once you have kies installed go to tools and install drivers.
Remember that before you open Odin you go through task manager to close all kies processes.
Good luck
Sent from my GT-I9000 using XDA
Got it to work
I was finally able to get it to work. I think I was using the wrong recovery screen or at least what I thought was a recovery screen because I finally got the guy in the construction picture and it flashed no problem with Odin.
After Odin Succes
Everything is ok and all thred completed (succesd 1 / failed 0)
After this, my galaxy tries to reboot but it only shows the flashing battery and will not reboot itself.
Help!
jimnycricket65 said:
Everything is ok and all thred completed (succesd 1 / failed 0)
After this, my galaxy tries to reboot but it only shows the flashing battery and will not reboot itself.
Help!
Click to expand...
Click to collapse
i have similar problem. Please have you gotten solution to this problem? Your help is appreciated. Thanks.
are you instaled drivers completly???
alireza17mah said:
are you instaled drivers completly???
Click to expand...
Click to collapse
Right Click -> Run As Administrator it should resolve the issue
If its showing the battery only then its probably the wrong flash file.
Sent from my GT-I9000 using xda app-developers app

[Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode screen

[Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode screen
Hi,
I was trying to install new ROM through Odin software. I tried with Odin3 one click downloader. I also tried using KI2 with Boog's Kernel odin software. but both are failing. Shows FAIL with following output -
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
Another problem is that for my Samsung Captivate mobile... Download mode screen stopped coming ( I think it happened when by mistake I updated mobile's bootloader with some Corn s/w bootloader by selecting the file in Bootloader field in Odin. It created a big problem for me. I couldn't go in to download mode after this.
So finally I purchased USB jig to enable Download mode (last option to make mobile in download mode).
Even though I can update the firmware using Jig. But still download mode screen is not coming.But when I connect mobile to computer with usb cable, after using USB jig, I could see that odin shows "ADDED" with yellow box showing some port no. Above output comes when i continue with installing tar/md5 file of ROM with Odin. but it fails. So i am unable to use my mobile... .
It worked when I updated ROM with following package - GT_I9000_ZSJPK_ZSJPG_OZSJPG. It contains PDA, PHONE and CSC files.
First I did partition with file s1 odin 20100512.pit and after that I selected these three files in corresponding fields in Odin software and clicked on start button. It worked and i could see FROYO installed in my captivate phone. But this ROM update is for I9000 mobile. so all functionality is not working properly. what i mean to say here that I can update mobile with I9000 ROM. but not with captivate ROM.
My mobile's situation is that it has no software installed. Just as a hardware. No Bootloader, Nothing. Even AT & T screen doesnt come when I start my mobile. It is totally dead.
Can anybody please help me ? how can I resolve this problem. I searched all the thread in forum. But it is not helping me to resolve my problem. .
Issues are -
AT & T screen is not coming when i start the phone.
Download mode screen is not coming when i start the phone.
Just Assume that I have captivate phone without partition, without bootloader ...
Can anybody please help ?
vishu_10d said:
Hi,
I was trying to install new ROM through Odin software. I tried with Odin3 one click downloader. I also tried using KI2 with Boog's Kernel odin software. but both are failing. Shows FAIL with following output -
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
Another problem is that for my Samsung Captivate mobile... Download mode screen stopped coming ( I think it happened when by mistake I updated mobile's bootloader with some Corn s/w bootloader by selecting the file in Bootloader field in Odin s/w. It created a big problem for me. I couldnt go in to downlaod mode after this.
So finally I purchased USB jig to enabled Download mode (last option to make mobile in downlaod mode).
Even though I can update the firmware using Jig. But still download mode screen is not coming.But when I connect mobile to computer with usb cable, after using USB jig, I could see that odin shows "ADDED" with yellow box with some port number. Above output is comes when i continue installing tar/md5 file of ROM with Odin. but it fails. So i am unable to use my mobile... .
It worked when I updated ROM with following package - GT_I9000_ZSJPK_ZSJPG_OZSJPG. It contains PDA, PHONE and CSC files.
First I did partition with file s1 odin 20100512.pit and after that I selected these three files in corresponding fields in Odin software and clicked on start button. It worked and i could see FROYO installed in my captivate phone. But this ROM update is for I9000 mobile. so all functionality is not working properly. what i mean to say here that I can update mobile with I9000 ROM. but not with captivate ROM.
My mobile's situation is that it has no software installed. Just as a hardware. No Bootloader, Nothing. Even AT & T screen doesnt come when I start my mobile. It is totally dead.
Can anybody please help me ? how can I resolve this problem. I searched all the thread in forum. But it is not helping me to resolve my problem. .
Issues are -
AT & T screen is not coming when i start the phone.
Download mode screen is not coming when i start the phone.
Just Assume that I have captivate phone without partition, without bootloader ...
Can anybody please help ?
Click to expand...
Click to collapse
Here's what you need: http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Grab Odin KK4 with bootloaders from that thread. That should get your phone back up. If you wanna get farther and flash a custom ROM, follow http://forum.xda-developers.com/showthread.php?t=1350266
BWolf56 said:
Here's what you need: http://forum.xda-developers.com/showpost.php?p=18370912&postcount=3
Grab Odin KK4 with bootloaders from that thread. That should get your phone back up. If you wanna get farther and flash a custom ROM, follow http://forum.xda-developers.com/showthread.php?t=1350266
Click to expand...
Click to collapse
Thanks for the reply...
I tried with Odin one click downloader also... but it is failing... attaching the image...
Re: [Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode scr
Try a different micro usb/usb cable. And also a different usb port if the different cable doesn't work.
And if that fails...some Captivates don't like One Clicks, so see my post here...http://forum.xda-developers.com/showthread.php?p=30840818
Then use the [Utility]KK4 Easy Root by Red_81 http://forum.xda-developers.com/showthread.php?p=26710533 to get Root and KK4 Corn Kernel that has CWM Recovery...if u want.
Another helpful sticky thread...http://forum.xda-developers.com/showthread.php?p=33227541
Sent from my SAMSUNG-SGH-I747 using xda premium
4-2ndtwin said:
Try a different micro usb/usb cable. And also a different usb port if the different cable doesn't work.
And if that fails...some Captivates don't like One Clicks, so see my post here...http://forum.xda-developers.com/showthread.php?p=30840818
Then use the [Utility]KK4 Easy Root by Red_81 http://forum.xda-developers.com/showthread.php?p=26710533 to get Root and KK4 Corn Kernel that has CWM Recovery...if u want.
Another helpful sticky thread...http://forum.xda-developers.com/showthread.php?p=33227541
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Hi,
I followed the steps written in the forum above. But that is not working my case. I tried the steps in different computer with diff OS installed. but still same problem.
Is there any way to get PHONE, PDA, CSC file separately for i897 ? I could install I9000 in my samsung captivate mobile which had these files. So just thought, if i can get these files for i897, probably it should work?
Any Idea where i can get these files?
Re: [Q] Samsung Captivate phone is dead, not showing AT & T screen, download mode scr
^
Here ya go...http://forum.xda-developers.com/showthread.php?p=19587108
Sent from my SAMSUNG-SGH-I747 using xda premium
4-2ndtwin said:
^
Here ya go...http://forum.xda-developers.com/showthread.php?p=19587108
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Hi,
Still my problem is same. I went through the link. but that is also not helping.
In my phone, I cant see download screen, even though if i use USB jig.
When I run Odin s/w, I can see in odin as port "Added" when Connect my mobile with computer using usb port.
Usually Odin show port added when u are in download mode. But here in my case, when i first USB jig and then connect to computer, download mode screen message and image doesnt come. it shows nothing(like no display). But I can see , Odin shows port Added. and I could update kernel, do partitions etc. But when I select Image file as PDA. and click start. It always fails.
Is it happening because i cant see download mode screen ?
1. What firmware I need to install and how which contains code for showing download screen ?
2. Or can anybody provide me all files i.e. PIT, Bootloader, PDA, Phone, CSC for odin so that i can select all files in respective fields under Odin software and start update?
Please help.
One more thing i have noticed.. here is the output of odin when i update my mobile with following files of I9000 model. while trying images for my captivate mobile, I found a zip file for model GT I9000 and package name was -GT_I9000_ZSJPK_ZSJPG_OZSJPG. It had three files as - 1. CSC_OZSJPG.tar.md5. 2. PDA_ZSJPK.tar.md5. 3. PHONE_ZSJPG.tar.md5.
I selected this files in corresponding PHONE, CSC, PDA fields in odin and it updates phone successfully with the following output -
<ID:0/017> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PDA_ZSJPK.tar.md5 is valid.
<OSM> PHONE_ZSJPG.tar.md5 is valid.
<OSM> CSC_OZSJPG.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/017> Odin v.3 engine (ID:17)..
<ID:0/017> File analysis..
<ID:0/017> SetupConnection..
<ID:0/017> Initialzation..
<ID:0/017> Set PIT file..
<ID:0/017> DO NOT TURN OFF TARGET!!
<ID:0/017> Get PIT for mapping..
<ID:0/017> Firmware update start..
<ID:0/017> param.lfs
<ID:0/017> zImage
<ID:0/017> factoryfs.rfs
<ID:0/017> dbdata.rfs
<ID:0/017> modem.bin
<ID:0/017> cache.rfs
<ID:0/017> Removed!!
<ID:0/017> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/018> Added!!
<ID:0/018> Removed!!
<ID:0/019> Added!!
But even though i can see my phone with I9000 model image installed. but most of the operations it doesnt work. might be becoz image is not fully compatible with Captivate model. so no use.
You should always be able to see the download screen no matter what fw you're on. I could see it on 2.3.5, 4.2.2, etc. Even with a jig you can't force it into download mode? Did you make it or buy it?
x0ne215 said:
You should always be able to see the download screen no matter what fw you're on. I could see it on 2.3.5, 4.2.2, etc. Even with a jig you can't force it into download mode? Did you make it or buy it?
Click to expand...
Click to collapse
I purchased a jig for samsung captivate from ebay website. when I tried with it, It doesnt show me downlaod mode screen. But it make my mobile able to connect to system. And I can see the port as added in odin. using that only I have installed android froyo of GT I9000 model in captivate mobile. I tried with all the PDA files available in forums here, but it didnt work.
Presesnt situation is, I am using captivate mobile which have android version of GT 9000 model. As I mentioned in the post.
vishu_10d said:
I purchased a jig for samsung captivate from ebay website. when I tried with it, It doesnt show me downlaod mode screen. But it make my mobile able to connect to system. And I can see the port as added in odin. using that only I have installed android froyo of GT I9000 model in captivate mobile. I tried with all the PDA files available in forums here, but it didnt work.
Presesnt situation is, I am using captivate mobile which have android version of GT 9000 model. As I mentioned in the post.
Click to expand...
Click to collapse
I'm curious do you ever see anything on your screen?
Sent from my SGH-I897 using xda app-developers app
m1batt1 said:
I'm curious do you ever see anything on your screen?
Sent from my SGH-I897 using xda app-developers app
Click to expand...
Click to collapse
Yes. As i Said. I am running Android version of GT 9000 on my Samsung Captivate model and it is working fine(except some cases e.g. screen orientation while running games and some other apps, Media sound doesnt come etc).
vishu_10d said:
Yes. As i Said. I am running Android version of GT 9000 on my Samsung Captivate model and it is working fine(except some cases e.g. screen orientation while running games and some other apps, Media sound doesnt come etc).
Click to expand...
Click to collapse
I think it meant something along the lines of ''What is showing on your screen while in download mode''?
BWolf56 said:
I think it meant something along the lines of ''What is showing on your screen while in download mode''?
Click to expand...
Click to collapse
Hi,
when i usb jig and after that connect to system. I can see port Added in Odin software. which ideally happens when mobile is in downlaod mode.
but here for me display doesnt show anything on screen, screen remain blank. No android icon comes. but still I can see port added in odin and also can install files in the mobile. like pit, bootloader PDA files. etc.
I have tried my image files which is available with bootloaders in forum. But when I start. I always get following error.
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
It always fails while executing sbl.bin files. I have gone through some forum where reports similar issue of sbl.bin.
Resolution which was given is to try with " 4 part flash files" which is Boot, PDA, Modem, CSC files.
http://www.droidevelopers.com/f299/14467-sbl-bin-error.html.
But this solution is not for captivate mobile.
It would be good if someone can provide me these files instead of a single installable file.
vishu_10d said:
I have tried my image files which is available with bootloaders in forum. But when I start. I always get following error.
<ID:0/016> Added!!
<ID:0/016> Odin v.3 engine (ID:16)..
<ID:0/016> File analysis..
<ID:0/016> Set PIT file..
<ID:0/016> DO NOT TURN OFF TARGET!!
<ID:0/016> Get PIT for mapping..
<ID:0/016> Firmware update start..
<ID:0/016> Sbl.bin
<ID:0/016>
<ID:0/016>
<OSM> All threads completed. (succeed 0 / failed 1)..
It always fails while executing sbl.bin files. I have gone through some forum where reports similar issue of sbl.bin.
Resolution which was given is to try with " 4 part flash files" which is Boot, PDA, Modem, CSC files.
http://www.droidevelopers.com/f299/14467-sbl-bin-error.html.
But this solution is not for captivate mobile.
It would be good if someone can provide me these files instead of a single installable file.
Click to expand...
Click to collapse
I believe 4-2ndtwin has the link to them in his sig.
BWolf56 said:
I believe 4-2ndtwin has the link to them in his sig.
Click to expand...
Click to collapse
So any suggestions ? what should I do now ?
vishu_10d said:
So any suggestions ? what should I do now ?
Click to expand...
Click to collapse
Search for 4-2ndtwin.. Go into his profile, then sig link and find the separated files.
vishu_10d said:
So any suggestions ? what should I do now ?
Click to expand...
Click to collapse
You need Jtag
Check my signature for more detail.
Here is the i897uckf1 gingerbread 2.3.3 files...http://forum.xda-developers.com/showthread.php?p=30840818...Post #284 in that thread.
Do not put any files in the Bootloader tab of Odin. Just PDA in pda tab, CSC in csc tab, PHONE in phone tab and also Pit file in the pit tab. Be sure to have a reliable usb/micro usb and constant power source. This firmware does contain the Bootloaders.
Sent from my SAMSUNG-SGH-I747 using xda premium
4-2ndtwin said:
Here is the i897uckf1 gingerbread 2.3.3 files...http://forum.xda-developers.com/showthread.php?p=30840818...Post #284 in that thread.
Do not put any files in the Bootloader tab of Odin. Just PDA in pda tab, CSC in csc tab, PHONE in phone tab and also Pit file in the pit tab. Be sure to have a reliable usb/micro usb and constant power source. This firmware does contain the Bootloaders.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Thanks a lot for providing me these files. This is what I wanted. I will try as you suggested and will let you know the result.
Thanks

Help needed for my phone

Dear All,
My phone was not working last month it will be stuck on samsung logo, then later i tried to use odin to put again firmware but it will fail on "system.img" .
Now my phone shows "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again".
In Kies my phone is not detecting at all in firmware emergency recovery.
Kindly help guys...i am really tensed. Even with other firmware in Odin its getting stucked in "system.img" and it fails.
help me guys...its showing in odin
<ID:0/011> Added!!
<ID:0/011> Odin engine v(ID:3.1005)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
https://forums.androidcentral.com/g...e-write-operation-failed-what-can-i-do-2.html
Maybe this will help or try a different usb port? Also look on youtube theres some helpful vids on there or uninstall kies it can sometimes interfere with odin good luck.
are you sure your unit is thecorrect one for correct firmware?
what does it say on what model it is on DL mode?
supertac said:
are you sure your unit is thecorrect one for correct firmware?
what does it say on what model it is on DL mode?
Click to expand...
Click to collapse
GT-I9305
still unable to solve
permission to double to post:
i cant even put another firmware...it always fails on NAND System, does my phone has hardware issue?

Categories

Resources