[Q] is my i9000 bricked? - Galaxy S I9000 Q&A, Help & Troubleshooting

My i9000 respond to Downloading Mode (Volume Down+Home+Power) but it doesn't boot...the logo stay on and on until I decided to take off the battery.
Is there a foolproof method to recover my phone? It was locked to T-Mobile and has been unlocked to all networks and rooted - the ROM was Gingerbread 2.3 and working perfectly until I decided to "upgrade" to Jelly Bean...:silly:
I did backup the previous ROM via CWR but right now I can't access any partition...
Help!

with gazbil
Does ODIN recognize your phone when you're in download mode? If so, you should be able to flash gingerbread without losing all your data.

Skire90 said:
Does ODIN recognize your phone when you're in download mode? If so, you should be able to flash gingerbread without losing all your data.
Click to expand...
Click to collapse
thanks for your reply....
Yes Odin recognize my phone and I've tried to update using "JW4" (these 3 letters represent the end of a ROM file which isn't Gingerbread - I've followed this tip from another thread) - Odin says PASS (green box) but when I try to reboot the phone get stuck in Recovery mode (3?) - there are some errors, related to Data and Cache which I believe need to be erased from previous install but still no luck...
I'll try to post a picture of the error messages (or maybe I just copy the text here). At least the booting gives some signals now - there is a logo loop while before there was no boot whatsoever - so, things seems to improve a bit.

solved!
I've solved the problem by installing dbdata.rfs:
hope this helps others....
in the end I got into troubles because I didn't wipe data and cache before flashing the new ROM.

Related

Help me please...galaxy tab Exclamation mark

i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
water30 said:
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
Click to expand...
Click to collapse
what did you do to get to this screen? Is this after or before you upgraded firmware?
GANJDROID said:
what did you do to get to this screen? Is this after or before you upgraded firmware?
Click to expand...
Click to collapse
after upgrade firmware odin show reset but the my tab not reset then i just manual reset (i can take this method for my galaxys ) after that.....
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
primeroz said:
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
Click to expand...
Click to collapse
Read my above post. Go into download mode (volume down + home + power) you'll still have the same image but the phone WILL be in download mode. Then flash your previous firmware and you're sorted.
Sent from my GT-P1000
You probably got that by messing with the kernel. Fund the zImage from the firmware, extract it with a .tar extractor then use something like heimdall to flash the kernel and it should work.
Sent from my GT-P1000 using Tapatalk
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Help please
slaia said:
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Click to expand...
Click to collapse
Having the same problem too... anyone can help?
If you see Phone-!-Pc on the Tab screen it is the download mode.
You can reflash it using Odin, however, you will need to do full Rom flash. I had similar problem and solved it by replashing.
I followed the latest guide published in this forum and Roto-JME rom with reformatting of internal sd.
Phone ! PC error FML!!!
GANJDROID said:
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
Click to expand...
Click to collapse
Where can i download the JM6 zip??
Hey guys,
I tried to manually update my tab to Gingerbread today via Odin, but it kept hanging on select partition (I discovered I used the wrong PIT for the firmware I was going to flash, but as I didn't select the firmware yet that shouldn't be a problem). At last I decided to quit Odin (which might have been stupid...) and try it again. Then it kept haning even earlier, so I tried to restart the device in download mode. However, whatever I try it keeps giving the Phone ! PC sign. If I try to just boot, if I try to go into recovery mode or if I try to go into download mode. I saw a lot of possible ways to solve the problem, but my PC doesn't recognize the tab anymore. If I connect it, it does give the "usb device connected" sound, but there is a popup which sais "USB Device not recognized. One of the USB Devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message". I already tried to reinstall the driver but it doesn't work. Also Odin and Heimdall don't detect any device.
Does anyone know a solution for this problem? Maybe taking the battery out? (for which I have to buy a new triangle screwdriver, so I need to know if it could possibly work first. It takes some weeks to order such a thing I think...)
EDIT: I played around a bit with the drivers again, and suddenly both Heimdall and Odin recognized it. However Odin stopped recognizing it again. Then I pressed "read PIT" in Heimdall, which worked. After that the device started booting up to the Samsung logo animation and then powered off again. Now it doesn't do anything anymore, not even showing the Phone ! PC screen. I'll charge it overnight (maybe it's gone empty during the process), so I hope that helps.....
In some strange way, the phone works again..... So never mind my post above.

[Q] Phone won't boot, simply vibrates.

Hey guys,
I tried to update my girlfriends Galaxy S today from Darky's rom to Miui, I tried to remove the lagfix by following the instructions through recovery.
However, after the phone rebooted it now displays the Galaxy S logo, then simply vibrates periodically (every 5 seconds, than every 12 - not that I think this matters).
Does anybody have a clue what I've inadvertently done and how to recover the device - preferable without wiping the data on-board.
Thanks in advance guys.
Just an update, it's clearly a soft brick. I can still get into download mode and recovery, it did a backup before it rebooted however I've tried to restore this backup and still no joy - although I do now get the old rom's boot animation back which is stuck on an endless loop with the phone vibrating in the background.
You probably won't be able to fix it without a wipe. You should still be able to get into download mode, so you can flash a full ROM with Odin. You need to use a .PIT file and make sure repartition is checked as the file system is probably broken.
DrFredPhD said:
You probably won't be able to fix it without a wipe. You should still be able to get into download mode, so you can flash a full ROM with Odin. You need to use a .PIT file and make sure repartition is checked as the file system is probably broken.
Click to expand...
Click to collapse
Yeah miui uses a different file system so you have to undo that as described above. Then you may be able to restore the backup.
Sent from my GT-I9000M using XDA Premium App
After you guys pointed me in the right direction and a little more digging I ended up stumbled across galnet's Miui thread and his instructions through there.
To cut a long story short the phone's now running Miui and I'm not in the dog house, thanks for the help guys.
Where would I get a JTAG repair?

[Q] Bricked Galaxy Mini

Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
u cant even enter recovery?if u can,just wipe cache and data..
Sent from public phone using 10cents.
ybregeon said:
Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
Click to expand...
Click to collapse
Just remove the battery and stop your phone.
Put the battery in again.
Go to recovery mode by pressing Home + Power button at the same time.
In the reocevey choose wipe data/factory reset option.
Reboot your device after you are done.
You mobile will boot up fine.
Thank you for your answers but I wanna insists on a point: I can't access recovery at all, the phone show me the samsung logo for about half a second then restarts, and is looping in this state. No recovery, only downloading mode and RAMDUMP Mode (ARM9 mode) & Emergency Dload Mode (ARM9 Mode). Nothing else is avalaible.
Helppp
ybregeon said:
Hi, I live in Egypt for a while and I bought last month a Mini. Everything was going just fine, I was using Odin many times to try new roms, and CWM Recovery to give a try to custom roms, without problems. Yesterday morning I flashed my device with the 2.3.6 rom that I found on this forum, apparently made for Latin America. Since that moment, my mobile is on boot loop, i can't do anything, I only can access downloading mode, I tried to reflash gingerbread 2.3.4, and2.3.5, it goes well, Odin gives me the PASS message, but still my mobile is forever rebooting at Samsung logo. I can't access recovery.
What to do? Is it bricked and do I have to send it to Samsung Center or is there hope to fix it by myself?
Thank you for any help...
Yohan
Click to expand...
Click to collapse
hey man i've already had that problem..coz i flash 2.3.6 and encountered same problem but i manage to fix it.. you need to enter recovery mode... Note: you need to hold the home & power button and wait for the samsung logo to flash TWICE (2X),when the 2nd logo flash, just realease the buttons and your on recovery mode.just wipe/ data reset.. right now im using Ginger bread 2.3.6JKVT and its rooted also.
No, I can't access recovery sorry.
Connect your phone to your laptop.
Use ADB
Type this :
adb shell reboot recovery
That will take you to download mode,then you can flash rom again. It would be easier if you have a CWM installed
Sent from my GT-I5500-MADTEAM using Tapatalk
Shall I use Downloading mode to do this?
ybregeon said:
Shall I use Downloading mode to do this?
Click to expand...
Click to collapse
If you can't access recovery either falsh CWM recovery or Flash another firmware from Download mode. If you want to flash CWM recovery just follow the link below for Galaxy Mini and search CWM recovery.
I tried many times, since i have this problem, to flash and reflash, official roms, CWR, but nothing works, setup goes fine according to Odin, but still have the problem on my phone, still only downloading mode works, and still a flashing screen, just during the samsung logo.
No one can help me with my mobile???
ybregeon said:
No, I can't access recovery sorry.
Click to expand...
Click to collapse
did you wait for the samsumg logo to flash tiwce while holding the combo key? you see when im installing firmware using odin my laptop turn off coz i dont have a battery i thought my mini was brick because the process was not finish,so what happen i tried to acces recovery mode its only shows a computer icon & phone icon. but i manage to fix the problem i go to download mode and flash again another firmware. and everything goes fine..so how come that you cant access recorvery...i would suggest that you flash a firmware with 4 parts not a single package.
just try this www*mediafire*com/?br3r8fod5g3vud4 flash this firmware with Odin this will surely work please replace * with . brace my post count is not enough to post outside link
As long as you can enter download mode... you are safe. If you can... just flash it back with Odin.
Follow this step
http://forum.xda-developers.com/showthread.php?t=1107331
Thanks but no
dhlalit11 said:
just try this www*mediafire*com/?br3r8fod5g3vud4 flash this firmware with Odin this will surely work please replace * with . brace my post count is not enough to post outside link
Click to expand...
Click to collapse
Thank you for the link, i tried but still have the same problem. Could this be an EEPROM problem?
ybregeon said:
Thank you for the link, i tried but still have the same problem. Could this be an EEPROM problem?
Click to expand...
Click to collapse
Try booting up without micro sd nor sim card.
Sent from my neighbour’s android phone
i had a same problem too.
my phone cannot power on, and ONLY download mode only working.
i flashed it for so many time too, and it doesn't seem to fix the problem.
so any fix on this ?
To ybregeon and Tre3,
I had the exact same issue, only Download Mode and RAM Dump, but could not enter recovery mode. Tried flashing many ROMs, oneclick unbrick, Heimdall recovery etc. but still no solutions available, I tried many-many tricks with no luck. So I went to Samsung Service Center, and it turned out that the problem is in the mainboard. It took me one night before Samsung replaced the mainboard from my phone and it's been working well since. All free of charge.
I hope your warranty is still valid. Good luck.
Sent from my GT-S5570 using XDA App
distan7 said:
To ybregeon and Tre3,
I had the exact same issue, only Download Mode and RAM Dump, but could not enter recovery mode. Tried flashing many ROMs, oneclick unbrick, Heimdall recovery etc. but still no solutions available, I tried many-many tricks with no luck. So I went to Samsung Service Center, and it turned out that the problem is in the mainboard. It took me one night before Samsung replaced the mainboard from my phone and it's been working well since. All free of charge.
I hope your warranty is still valid. Good luck.
Sent from my GT-S5570 using XDA App
Click to expand...
Click to collapse
reflash the XXKPI/XXKPK 2.3.4 then flash the cmw, xxkpi and xxkpk is the safest stock gb rom to install
Flash odin and go to recovery mode and wipe.
It should work.

[Q] Messed it up and need help

This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.
Do not flash thru CWM... Flash a good GB kernel like "franco.Kernel" but thru PC Odin then u can flash whatever u want from franco's CWM... Good luck
Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.
Ce said:
Don't need help anymore
Note is officially bricked. After several attempts to recover from a softbrick the screen of my Note didn't turn on anymore. No button or button combination works, no recovery and no download mode, just a black screen.
Click to expand...
Click to collapse
Flat battery? It's also possible that it's just the screen that's not working. Try entering download mode "blind". So hold power+home+vol down for ~10 seconds, then press vol up. Hook it up via usb and see if Odin can recognize it.
Thanks, didn't think of that. But unfortunately no response from the device.
So now that it looks like your phone is officially bricked, I think you should just take it to Samsung and make up a story. Like you were updating your software with Kies and something happened and the phone is just not booting up.
I am sorry you bricked your note though..
try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose
musashiro said:
try AMORA Filemanager.. flash via recovery and you have a file manager,,, take a look on your partitions
just my idea, you got nothing to lose
Click to expand...
Click to collapse
I would like to but it's very hard when you can't see anything on the screen...
Maybe it's just the battery, try to charge it externally and try a JIG also
Sent from my GT-N7000 using XDA
Just a quick, final, update.
My Note was superbricked. Had to send it to a Samsung Service Center. No additional questions were asked. Samsung replaced the mainboard. Didn't have to pay anything.
Great service!!!
try this out buddy, do it on your own risk!!! anyways you have messed it up.
Ce said:
This WAS the situation before the problems:
Rooted Gingerbread rom, all working fine. Decided to unroot and install the full version of the official German ICS rom by using PC Odin. All went fine and used my Note for over two days. Because of the lags en slow responses I decided to reflash the ICS rom. From that moment on I messed it up. I've been reading and searching hundreds of posts for almost a day but didn't find a solution.
This IS the current situation:
I can get into download mode
I can get in recovery mode
However, in recovery mode I can not install a rom, every flash (CWM, both ICS and GB - even using chainfire's rom needed for rooting) stops on a random moment...but never gets it to the end, even if I wait several hours. Installing is very...very....very slow.
In recovery mode i can not restore a Nandroid backup, both ICS and GB. Every backup stops when /system has te be installed. errormessage.
In download mode I can connect my Note to PC Odin. I can select a rom and start flashing. However, after appr. 80% installation halts during "nand write start", no error message. The flashing does not finish, even after hours.
Funny is, i can install a kernel like Abyss.
So, I can't restore, i can't flash using cwm in recovery and I can't flash using PC Odin. My device seems not fully bricked. The max I get when rebooting (knowing that the process has not finished) is the triangle screen.
Any advise is appreciated.
Click to expand...
Click to collapse
i was not a member when i commited this mistake. but then big thanks to this community it helped me back from softbrick.
first you do is install a stock kernel of ics on your note go into recovery and just clear cache partition, thats it no wipe/data factory reset.
then,
install the pit file from this thread, also read it completely before proceeding. http://forum.xda-developers.com/show....php?t=1667886 , hoping yours is 16gb version and also read this thread for additional info but its quite complicated for me so im just telling you the direct method and hopefully itll get your note back to work. so once you download the 16gb pit file unzip it and in the unzip folder you will find a separately lying pit of 16gb stating patched-standard thats the one you want.
then,
goto samfirmware and download the latest ics firmware(i downloaded the indian one as it is in file .tar),
unzip it till you get .tar file.
open odin- click pit-select 16gb patched standard pit- check wether repartion is ticked- click pda-select the .tar file you extracted connect your phone and start. this time i wont stop at factory.fs.....
NOTE THAT AFTER THIS PROCEDURE IS COMPLETED SUCCESSFULLY YOUR INTERNAL STORAGE WOULD BE ONLY 8GB INSTEAD OF 11 GB STOCK WHICH YOU WERE GETTING.
I REVIVED MY NOTE THROUGH THIS PROCEDURE. PROCEES AT YOUR OWN RISK.
one your phone is working you'll be able to reset the counter with a jig and get your phone under warranty and get your motherboard changed by teliing at the Samsung Service that you are getting only 8gb instead of 11gb you used to get earlier(warranty only if you had any).
hope this helps mate.
BEST OF LUCK!!
A BIG HUGE THANKS TO hg42.....

[Q] galaxy ace s5830D in BOOT LOOP, no access to 'RECOVERY'

Hi gals and guys, I bought a new galaxy ace s5830D (gingerbread) from Telus and decided to unlock it the following way:
1. root using Universal_GB_ROOT_v10.zip
2. installed SuperOneClickv2.1.1-ShortFuse.zip on PC
3. installed Root Explorer (File Manager) v2.19.apk
4. used ADB shell on PC to read ST5L for unlock code
here is where the problem begins:
-- upon reboot phone goes in a bootloop (screen lights for a sec without Samsung logo)
-- I CANNOT put phone in recovery via home + power
--I CAN put phone in 'download' via power + home + vol dwn; or to RamDump with vol Up; or to Emergency Dload Mode by holding both up and dwn
I have tried the following:
-- flash stock telus rom S5830DTLKI4_S5830DTLSKI4_S5830DTLKI4_HOME.tar using ODIN. The flash goes successful but upon reboot goes back to bootloop? And still cannot enter 'recovery'
-- tried to flash cwm-recovery-ace.tar.md5 using ODIN. The flash is successful but on reboot goes to bootloop. Still no acess to 'recovery'
-- tried QtADB but cannot connect to phone
-- tried OneClickUnbrick but it will not recognize connection to phone either
-- tried AndroidSDK however cannot get to recognize device
So any ideas considering the main thing is I cannot get to 'recovery' and flashing with ODIN still results in bootloop.
Thanks for any advice
tedxdadevelopers said:
Hi gals and guys, I bought a new galaxy ace s5830D (gingerbread) from Telus and decided to unlock it the following way:
1. root using Universal_GB_ROOT_v10.zip
2. installed SuperOneClickv2.1.1-ShortFuse.zip on PC
3. installed Root Explorer (File Manager) v2.19.apk
4. used ADB shell on PC to read ST5L for unlock code
here is where the problem begins:
-- upon reboot phone goes in a bootloop (screen lights for a sec without Samsung logo)
-- I CANNOT put phone in recovery via home + power
--I CAN put phone in 'download' via power + home + vol dwn; or to RamDump with vol Up; or to Emergency Dload Mode by holding both up and dwn
I have tried the following:
-- flash stock telus rom S5830DTLKI4_S5830DTLSKI4_S5830DTLKI4_HOME.tar using ODIN. The flash goes successful but upon reboot goes back to bootloop? And still cannot enter 'recovery'
-- tried to flash cwm-recovery-ace.tar.md5 using ODIN. The flash is successful but on reboot goes to bootloop. Still no acess to 'recovery'
-- tried QtADB but cannot connect to phone
-- tried OneClickUnbrick but it will not recognize connection to phone either
-- tried AndroidSDK however cannot get to recognize device
So any ideas considering the main thing is I cannot get to 'recovery' and flashing with ODIN still results in bootloop.
Thanks for any advice
Click to expand...
Click to collapse
What ROM are you trying to flash with ODIN, because I couldn't find any on SamFirmware. Also in order to use ADB, you need the drivers, make sure you have them installed (they automatically install when you install Kies).
tedxdadevelopers said:
Hi gals and guys, I bought a new galaxy ace s5830D (gingerbread) from Telus and decided to unlock it the following way:
1. root using Universal_GB_ROOT_v10.zip
2. installed SuperOneClickv2.1.1-ShortFuse.zip on PC
3. installed Root Explorer (File Manager) v2.19.apk
4. used ADB shell on PC to read ST5L for unlock code
here is where the problem begins:
Click to expand...
Click to collapse
The stl5 method might damage the efs partition. It's a coinflip, with 3 outcomes:
-all goes well and you get an unlocked ace.
-your imei becomes 00000000000000 in which case you get aa working ace, but many carriers deny service to that imei, so no calls, no sms, no movile data.
-completely f****d up efs partition. You loose your imei. That's it, you're toast. No amount of flashing fixes this, it's not a hardbrick, but no rom will boot appropriately.
Try and flash a full package with odin. Make sure you use the correct odin version for your model and have the correct firmware. Then go into recovery and wipe everything, see if it boots. If it boots, open up your call app and dial *#06#* to see your imei (to make sure its still there).
If you have successfully flashed with odin before, and still won't boot or go into recovery, then maybe your efs partition got messed up.
Return the phone to telus, just don't tell them what you did.
thanks for the suggestions.. few more questions
-- any suggestions as to what to tell telus that is believable that happened? (phone is 3 days old and i bought it outright)
-- also re Efs partition damage, is there any way to repartition the phone and rewrite imei (isn't it on the stickers behind the battery)?
with ODIN i flashed (several times - all successfully) the stock rom made for the TELUS D version on the Ace. Its someone that build it from a stock Ace. Its available if u google it and many ppl have returned their Telus phones to stock telus\koodoo status via that rom with proprtietary carrier startup screen and all. The Model D of the Ace is not at all available on the SamFirmware site.
I also flashed only the CWM Recovery - sucessfully and still no access to 'recovery' menu.
ODIN i am using is the right version according to all i have read (4.42); and the .ops file is made, as I understand it, for partitions of the D version of the Ace. (odin + ops + rom was all one package that many ppl from telus have said to have used sucesfully to return their phones to stock.)
-- should i try to flash with odin a cyannogen mode 7.2.0; could that make a difference vs stock rom, or does the cyannogen just go on top of the stock rom; ie will not function without a proper stock rom? (i guess what i am asking is cyannogen a complete self contained os?)
--If the efs partition is damaged does it make sense then, that the ADB, oneclick unblock etc.., will not recognize the phone? Am i supposed to be able to even connect to ADB when phone is in 'download mode'? or its made to work only when phone is already booted up?
thanks guys again.. T
tedxdadevelopers said:
thanks for the suggestions.. few more questions
-- any suggestions as to what to tell telus that is believable that happened? (phone is 3 days old and i bought it outright)
-- also re Efs partition damage, is there any way to repartition the phone and rewrite imei (isn't it on the stickers behind the battery)?
with ODIN i flashed (several times - all successfully) the stock rom made for the TELUS D version on the Ace. Its someone that build it from a stock Ace. Its available if u google it and many ppl have returned their Telus phones to stock telus\koodoo status via that rom with proprtietary carrier startup screen and all. The Model D of the Ace is not at all available on the SamFirmware site.
I also flashed only the CWM Recovery - sucessfully and still no access to 'recovery' menu.
ODIN i am using is the right version according to all i have read (4.42); and the .ops file is made, as I understand it, for partitions of the D version of the Ace. (odin + ops + rom was all one package that many ppl from telus have said to have used sucesfully to return their phones to stock.)
-- should i try to flash with odin a cyannogen mode 7.2.0; could that make a difference vs stock rom, or does the cyannogen just go on top of the stock rom; ie will not function without a proper stock rom? (i guess what i am asking is cyannogen a complete self contained os?)
--If the efs partition is damaged does it make sense then, that the ADB, oneclick unblock etc.., will not recognize the phone? Am i supposed to be able to even connect to ADB when phone is in 'download mode'? or its made to work only when phone is already booted up?
thanks guys again.. T
Click to expand...
Click to collapse
Hey again, changing IMEI is illegal in some countries:
Here is a link on how to change it though.
when I go to repair my phone, they normally don't ask why does this happen, they just ask what's the problem. ALso, you have to pretend you are really angry, because the phone broke just 3 days after buying it. That's all. Just be sure that the boot animation is from the stock ROM, as well as the currently installed ROM.
Good deal, had phone exchanged for a new one. That should serve as a lesson to those trying to screw with their efs/ that sometimes it may actually NOT work!!
Thanks guys Cheers!

Categories

Resources