Hidead
I have flashed TWRP to a Kindle Fire. I did not know was that it was a fire version 2.
Now the device is completely dead.
no charging light, not recognized by pc, really nothing
Can I do something to bring the device back to run or I now have a really expensive paperweight?
found this Firekit LiveUSB repair kit 1.1
or is it for KF1 only?
depressed greetings from dortmund
dennis
vejoun5 said:
Hidead
I have flashed TWRP to a Kindle Fire. I did not know was that it was a fire version 2.
Now the device is completely dead.
no charging light, not recognized by pc, really nothing
Can I do something to bring the device back to run or I now have a really expensive paperweight?
found this Firekit LiveUSB repair kit 1.1
or is it for KF1 only?
depressed greetings from dortmund
dennis
Click to expand...
Click to collapse
I think everything you are looking at is for the original Kindle Fire.
Sent from my Galaxy Nexus using xda app-developers app
okay the kindle is lost for now. accepted maybe its possible to reanimate it in far future
ordered a new one
Gesendet von meinem HTC One X mit Tapatalk 2
Related
Hey Guys, i just got my brand new Kindle Fire HD 7'' just a few hours ago. Didn't do anything much on it, didn't even install drivers on my pc for it. i just connect it through WiFi and that's about it. i got a problem when putting in my email, so i guess i just put it in wrong so i was goin to try back later. When i came back to the Kindle, it was just at the boot screen ("kindle fire") and its been there since. I tried draining the battery, i also tried the hold down for 20 seconds but still no prevail. Guys i need your help i just got it. I live in Trinidad and returning the thing from amazon is a pain. it cost a lot of money to send it back. so help me out here guys thanks. :crying:
I am gonna guess a failed amazon ota update?
It sounds like you are gonna have to use the recovery software and a factory cable (usb with pins 1 and 4 shorted together)
And flash it back to stock, since a return to amazon is out...
Sent from my KFTT using xda app-developers app
mrkhigh said:
I am gonna guess a failed amazon ota update?
It sounds like you are gonna have to use the recovery software and a factory cable (usb with pins 1 and 4 shorted together)
And flash it back to stock, since a return to amazon is out...
Sent from my KFTT using xda app-developers app
Click to expand...
Click to collapse
Can u please provide links to the factory cable and recovery software?
Hi everyone. I want to buy Fire HD, but reason why i didn't done this yet is that i need to connect my MicroSD to it. I know i can do it by OTG cable, but default Kindle doesn't support it.
Would it be real, if i flash Kindle to CM10 (when it be realesed) ? I read that OTG is supported by kernel ICS and JB .
Thanks for answers
I really want to know this as well.
Sent from my SPH-L710 using xda app-developers app
donovanx3 said:
I really want to know this as well.
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
If this queston would see someone who already flash his fire HD to beta CM10 and try to do this :highfive:
I was looking through the source from amazon awhile ago and the drivers appear to be there, its just turned off in the current kernel. Admittedly I really know nothing about compiling anything, but it looks like it might be doable at some point in the future.
Last night, i was using the Kindle Fire First Aide to restore my kindle fire hd to 7.2.3. After it downloaded the files, it failed on one when flashing. All was fine though. I rebooted back to normal mode and it booted fine, i was using the Kinology rom. I then factory resetted my kindle and after rebooting, it now bootloops all the time.
My question now is, do i need a factory cable in order to fix my kindle fire hd or is it bricked??
If i do need a factory cable, would this one: http://www.amazon.co.uk/EARLYBIRD-S...59SG/ref=sr_1_1?ie=UTF8&qid=1362233872&sr=8-1 work fine?
Sorry if this doesn't make any sense.
Thanks for any replies you may give.
That cable will work fine.
Sent from my KFTT using xda premium
Krsmqn said:
That cable will work fine.
Sent from my KFTT using xda premium
Click to expand...
Click to collapse
Oh good. Thanks for the reply!
Quick question, when i get this cable, do i just plug it in to my kindle and it'll go into fastboot automatically or do i have to do something else??
Sn0wdune said:
Quick question, when i get this cable, do i just plug it in to my kindle and it'll go into fastboot automatically or do i have to do something else??
Click to expand...
Click to collapse
Power off the kindle, plug cable into Kindle, plug cable into computer.
Sent from my KFHD using xda premium
Krsmqn said:
Power off the kindle, plug cable into Kindle, plug cable into computer.
Sent from my KFHD using xda premium
Click to expand...
Click to collapse
Ah okay thank you. It will arrive within a few days
I'll post back when i have acquired the cable!
Cable arrived today It had a scorpion on it so i think its a skorpn cable
Anyway, it fixed my kindle fire hd 7 so kudos!
Thanks, you may now close this thread
Sn0wdune said:
Cable arrived today It had a scorpion on it so i think its a skorpn cable
Anyway, it fixed my kindle fire hd 7 so kudos!
Thanks, you may now close this thread
Click to expand...
Click to collapse
Glad to hear it. :good:
I bricked my Kindle Fire HD recently and was hoping that there was a way to enter fastboot on it without purchasing a fastboot cable. I don't have the money to buy one either. I have the img files and everything else needed. Thank you for your reply.
You will have to make one if you can't afford one, or try jumping two points on the motherboard with a wire. Fastboot cables are pretty cheap though, only around 5-15$.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
stunts513 said:
You will have to make one if you can't afford one, or try jumping two points on the motherboard with a wire. Fastboot cables are pretty cheap though, only around 5-15$.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Do you know how to jump 2 points on the motherboard with a wire? if so could you point me to a guide?
Here, just be careful, you don't want to hit the wrong leg and fry something. http://forum.xda-developers.com/showthread.php?t=2432650
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Lawlz I would rather not do that. Do you know how I can make a Fastboot Cable? I have about a million cables for the device. So could you lead me to a guide that I can use to make one with. If I take the device apart the chances of me breaking it is even higher.
If you don't have a soldering iron this could be very difficult to do by jumping a wire.... I believe Samsung cables are recommended because not all cables have a spot on the PCB for pin 4, and Samsung's typically do.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
How to for a fast boot cable
http://forum.xda-developers.com/showthread.php?p=39569189
Sent from my XT907 using xda app-developers app
wire55 said:
I bricked my Kindle Fire HD recently and was hoping that there was a way to enter fastboot on it without purchasing a fastboot cable. I don't have the money to buy one either. I have the img files and everything else needed. Thank you for your reply.
Click to expand...
Click to collapse
Buy a fastboot cord for 10 bucks. Meanwhile install ADB drivers and Kindle Fire FirstAide.
When the cord gets to you, run KFFA and restore to 7.2.3 and root and remove OTA updates all from KFFA.
You'll restore to 7.2.3 so you will have a nice matching boot.img to use from Hashcode's thread when you go to flash a 2nd bootloader and custom rom.
*face palm* I had the link to the tutorial on how to make a fastboot cable copied and I forgot to paste it in my post. Hehe my bad...
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
LinearEquation said:
Buy a fastboot cord for 10 bucks. Meanwhile install ADB drivers and Kindle Fire FirstAide.
When the cord gets to you, run KFFA and restore to 7.2.3 and root and remove OTA updates all from KFFA.
You'll restore to 7.2.3 so you will have a nice matching boot.img to use from Hashcode's thread when you go to flash a 2nd bootloader and custom rom.
Click to expand...
Click to collapse
*face palm* Read my post man. I just told you I don't have the money for it.
stunts513 said:
*face palm* I had the link to the tutorial on how to make a fastboot cable copied and I forgot to paste it in my post. Hehe my bad...
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
Click to expand...
Click to collapse
Lol You still have the link anywhere for me? I have a soldering iron somewhere in my garage. Just need a guide on how to make.
Read mrkhigh's post, he provided a link to it.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app
wire55 said:
*face palm* Read my post man. I just told you I don't have the money for it.
Click to expand...
Click to collapse
Maybe the face palm will fix your eyes so you can read the many other posts posted on here dealing with this issue. Like the part that recommends having a fastboot cord before messing with your tablet. Or how to UTMFSE to find the pin out diagram to make your own fastboot cord.
I wouldn't waste ten dollars on a fast boot cable till I needed one if your careful and all goes right there is no need for one and even at that I'd rather make one than pay for it given I have a Samsung cable.
I grant you I used one but just because I felt like making one. Didn't even use it for a few months
Sent from my XT907 using xda app-developers app
mrkhigh said:
I wouldn't waste ten dollars on a fast boot cable till I needed one if your careful and all goes right there is no need for one and even at that I'd rather make one than pay for it given I have a Samsung cable.
I grant you I used one but just because I felt like making one. Didn't even use it for a few months
Sent from my XT907 using xda app-developers app
Click to expand...
Click to collapse
Well after i opened cable up, I realized I don't have any Solder. LOL. I have a Soldering Iron, but no Solder. So now I just wasted my time practically until I can get solder.
I posted a thread earlier asking how to flash the Kindle Fire HD, and now I have bricked it, I read another thread that there was no way to fix it,
I followed SgtTom123's videos on youtube but then clicked on the wrong one and used the Kindle Fire Utility and used fire fire fire, the device does not boot now.
Any suggestions?
Sorry no. At this point in time there is no simple fix to this. In all honesty with the age of this device now and price of devices going down I doubt there will ever be a service to fix it unless someone does it for the community.
Sent from my XT907 using xda app-developers app
Kurohyou just released the pin outs on the 8.9" kindle motherboard for the emmc, so we should have the pin outs for the 7" soon enough which means we can fix it, we just require enough skill to solder some points on the motherboard to wires soldered to a USB sdcard reader. From there we can reflash the boot loader using the dd command from an Ubuntu live CD.
Sent from my Amazon Kindle Fire HD running CM10.1 Tablet UI using xda-developers app