[Q] Help Request on Chip identification - Galaxy S I9000 Q&A, Help & Troubleshooting

Hi,
I was going crazy trying to figure whi my i9000 doesn't start. I broke the screen and i've replaced this with another. Seeing i wasn't able to boot, i did the Unbreakeable mod wich got me into download mode and i was able to falsh a rom. The problem is that my power button didn't work either to power off the device!
I've checked the button twice and it's ok (it shortcuts the two terminals when pressed). the problem seems to be that in the spots marked with red arrows in the picture below, i don't have any components and it seems that there were some in these places. I need help to confirm if there are components in those spots and in that case, help figuring out wich component it is (resistor / capactior...) and its value.
I would be greatly thankfull to anyone who can supply any information.
Thank you in advance.

scarnia said:
Hi,
I was going crazy trying to figure whi my i9000 doesn't start. I broke the screen and i've replaced this with another. Seeing i wasn't able to boot, i did the Unbreakeable mod wich got me into download mode and i was able to falsh a rom. The problem is that my power button didn't work either to power off the device!
I've checked the button twice and it's ok (it shortcuts the two terminals when pressed). the problem seems to be that in the spots marked with red arrows in the picture below, i don't have any components and it seems that there were some in these places. I need help to confirm if there are components in those spots and in that case, help figuring out wich component it is (resistor / capactior...) and its value.
I would be greatly thankfull to anyone who can supply any information.
Thank you in advance.
Click to expand...
Click to collapse
Mmm, I'm not sure if other users can see the image attached. If not, please me know.
Anyway, please, if anyone can find the time to check this items I'd be greatly thankful.
Thanks!

Related

blue angle siemens SX66 power switch problem. please help

hi. My sx66 got problem with the power switche. I can not turn if off.( it only works for turn on and off the backlight and turn on the pda) Also the 4 buttons (start menu message, internet exploer ok/close) do not work propertly. Otherwise everything is working well. Can someone please help me what to do or what wrong with the mainboard? Thanks!
I have had the same problem, it was the small circuit board that controls the cursor. Unless you have parts you will need to send it in.
hi Cruzzer,
Can you tell me where the small board located. Does your pda have problem with the power switch? Thanks.
Dear Cruzzer,
You are right. I just fix my phone. Thanks for your help. luckily the guy next door have 2 boards, I tested both work 100%. he charge me 15 dollars for one. If you need one for your phone, let me know.

Stuck power button

Hi all, long time, Happy New Year.
I have an old IIi that I would like to try and get up and running again. The problem is ( and why it's on the shelf ) the power button is unresponsive, it doesn't push in, come out, it's sort of 'stuck' Has anyone seen this before, if so, any ideas on how to get around / fix this problem ?
Thanks in advance.
bopdude said:
Hi all, long time, Happy New Year.
I have an old IIi that I would like to try and get up and running again. The problem is ( and why it's on the shelf ) the power button is unresponsive, it doesn't push in, come out, it's sort of 'stuck' Has anyone seen this before, if so, any ideas on how to get around / fix this problem ?
Thanks in advance.
Click to expand...
Click to collapse
try to take off the black plastic antenna cover on the back and see if the small button on the main board is working... search this forums for the service manual... it tells you how to take that cover off.

Pls Help: Problem with Power Button

From yesterday onwards i am getting this problem.power button is nt workn as previous.Phone automatically get the signal of long press power button.it means automatically it asks "power will be turned off,and you may lose data if...".and also when i press power button it doesnt goes to standby mode.when i long press the power button sometimes it doesnt switch off..As i think the power button dnt work as normal or may it seems that power button keep pressed internally..pls help me to solve this problem.thnx in advance
some1 pls help me
naheelja said:
some1 pls help me
Click to expand...
Click to collapse
I'd suggest you make a full backup and hard reset the device in order to make sure its not a hardware problem. If it works fine after a hard reset, you'll know its something you installed relatively recently.
I did a hard reset.nothing changed.then i flashed a different ROM.But still i am facing the problem.
Try the following:
Get a can of canned Air and blow it on the button as it might move any debris that are there. Just make sure that the phone is off and the battery is out. KEEP THE AIR STREAM AWAY FROM THE SCREEN! If any of the propellant escapes while you spray, it can freeze the LCD. Just slide it open and stick some paper on top of the screen. Wait a few moments before you switch the device back on
If this doesn't work, flash the Kaiser with its original ROM and SPL just in case there is an odd interaction somewhere. See here: http://forum.xda-developers.com/showthread.php?t=418375
If nothing of the above work, you have two options:
a. If the device is in warranty, return it and get it fixed or replaced. Make sure is has its original ROM/SPL loaded before you do.
b. If the device is out of warranty/you don't care about the warranty, you can try to open it up and see if something is blocking the switch. There are instructions floating around here somewhere.
EDIT: Added warning regarding the propelant and the LCD
Any update here? My tilt is doing the exact same thing
alt236 pretty much said all there was to it. Hard reset, restore stock ROM, try blowing the switch, if all fails send for repair.
Did all of the above and the cost of repair is not worth it. Time to toss my kaiser I guess

HUGE problem ! HELP ! ( phone wakes on it's own ) (i uploaded a clip so ypu can see)

my TyTN II can't co to sleep - when I press the POWER button it goes to sleep and after 3 seconds it wakes again
PLEASE HELP ME
P.S. and it can not do a HARD RESET with the buttons
_______________________________________________________________________________________
here is a clip that I shot with my camera so you can see what is the problem
RAPIDSHARE - http://rapidshare.com/files/145255212/SL550774.MP4.html
GOOGLE VIDEO - http://video.google.com/videoplay?docid=2057235928163515395&hl=en
_______________________________________________________________________________________
Looks like a software or a regedit is keeping it from doing so. Try resetting the device and see what happens.
kareem9nba said:
Looks like a software or a regedit is keeping it from doing so. Try resetting the device and see what happens.
Click to expand...
Click to collapse
I did a soft reset - nothing
I did a HARD RESET- nothing
I changed the rom - nothing , it still wakes up
This has nothing to do with ROM Dev. Moved to General
I don't have a clue what it is
Ok i have had this problem before. But it is when i put the phone in universal car cradle. It hits the camera button half way so when i put it to sleep, it wakes back up after about 3 seconds. Make sure none of the buttons are partially stuck.
Frank
yes , now it has no autofocus
fordmav said:
Ok i have had this problem before. But it is when i put the phone in universal car cradle. It hits the camera button half way so when i put it to sleep, it wakes back up after about 3 seconds. Make sure none of the buttons are partially stuck.
Frank
Click to expand...
Click to collapse
and how did you fix it ???
do I have to open the phone or there is a softwere way to fix it ?
here is a clip that I shot with my camera so you can see what is the problem
RAPIDSHARE - http://rapidshare.com/files/145255212/SL550774.MP4.html
YOUTUBE - I'm uploading it there now , i will give you the link asap
UPDATE !!!!!
are you running igo8 in the background? Turning the phone off while running an *ahem* type of Igo8 may cause certain on/off issues...
I'm not running anything
Sorry bout the late reply. I work during the day so i didnt see this till now.
What i would suggest is turn on the camera and goto the settings. Make sure it asks for full press. Then attempt to take a picture, by half pressing the camera button, as this will make it auto focus. If the little broken square in middle of screen doesnt show, then it has something to do with your problem.
My problem wasnt an actual problem but rather an observation that i thought could help.
Ive just done a couple tests on my phone and the camera button is the only thing that causes this issue. I hold it half way as to not activate the camera and then turn the phone off to sleep, but after precisely 3 seconds, it wakes back up
Hope this helps you find it. As for solving it, i don't know. Possibly a few harder presses of the camera button???? Please, though, dont take what i am saying as Gospel as it may be something totally unrelated
Frank
i tried the thing with the setting for the full and half press and nothing , it was the same - the camera shoots ONLY WITH A FULL PRESS !
The good news is I took it for a repair
Hope u get it back soon with minimal repairs needed
Frank
more bad news - it turnd out that the camera button is realy stuck on auto focus but the realy bad thing is I CAN'T FIND A SPEAR CAMERA BUTTON
help me pleaseeee !!!!
I have this exact problem...press power button--3 seconds later phone back on again. Have flashed 6 different ROM's and it has not removed this issue. It is not any of my software because this remains before I add any of my software after a flash.....as per OP i am unable to do a hard reset.
I have done many searches on the forums and continually come up with the 10 second backlight fix....this is not the same issue.
If some of the senior members could please help I would greatly appreciate it.
Currently running a kaiser w/ L26 light...Hard SPL 3.29
griffin911 said:
I have this exact problem...press power button--3 seconds later phone back on again. Have flashed 6 different ROM's and it has not removed this issue. It is not any of my software because this remains before I add any of my software after a flash.....as per OP i am unable to do a hard reset.
I have done many searches on the forums and continually come up with the 10 second backlight fix....this is not the same issue.
If some of the senior members could please help I would greatly appreciate it.
Currently running a kaiser w/ L26 light...Hard SPL 3.29
Click to expand...
Click to collapse
At the moment my biggest problem is that i cant' find nother camera button for the motherboard
shtepsel said:
At the moment my biggest problem is that i cant' find nother camera button for the motherboard
Click to expand...
Click to collapse
It's not listed on their site, but it might be worth contacting these people.

Nexus One Power Button Issue

I have read many threads about the issues that the Nexus One has with the power button. I feel that my situation is a little different, so I wanted some opinions on this. My power button is completely unresponsive. I can't use it to turn the phone on, wake or lock my screen when the phone is on, etc. My phone has an unlocked bootloader and is rooted. I am currently using the track ball to wake my phone, so I'm not having any real issues with day to day operations of my phone. I was completely convinced this was a hardware issue (and still am), but I wanted to be 100% sure it was a hardware issue before contacting HTC. I downloaded Quick Boot from the android market which allows you to reboot your phone, boot your phone into your Bootloader, and boot your phone into Recovery. I decided to boot my phone into Bootloader mode to see if the power button would work there. The power button didn't work in the Bootloader, but neither did the volume button (prior to this test, I had no issues with the volume rocker at all). I pulled the battery and let the phone boot up to check and make sure the volume button was still working when the phone was running. Once the phone was booted up, I had no issues with the volume controls. My question is why would the volume rocker not work in the Bootloader? Also, could the issue that prevents the volume rocker from working in the Bootloader be preventing the power switch from working while the phone is booted up? If there is a chance that it's a software issue, how would I test/correct the issue? Thanks your help.
Most people I have seen complain about that problem, send the phone back for a free repair because it's a hardware problem.
The best way to test it is to flash a stock rom.
Thank you, I will try reflashing the FRF91 stock firmware and see what happens. Thanks.
Definatly sounds like the power button is broken. I had one like that. Send it back for a repair/replacement.
I've checked my immediate suspicion, and it turned out to be correct - so I'm posting the result:
Your power button is actually stuck in "ON" position (pressed).
Anyone can test it, press the power button to wake up the screen, keep it pressed, every operation is allowed in the system and volume buttons work. But when you reboot and try the same in bootloader, having power button ON disables the rest of the buttons.
My screen doesn't wake when I press the power button. Any other ways to check if it's stuck in the "ON" position?
It's 100% determined by your description. The only other check would be running any kind of SW that shows the current key states, and I'm not aware of any such SW.
I've posted the checking procedure for people with working power buttons, so they can verify the findings.
Any way to fix the issue?
If you're technically inclined and can't use warranty, I suppose that getting to the power button and repairing/replacing it wouldn't be very difficult. But no other way I can think of.
has anyone tried to repair this?
NEED a Do-IT-Yourself
Jack_R1 said:
If you're technically inclined and can't use warranty, I suppose that getting to the power button and repairing/replacing it wouldn't be very difficult. But no other way I can think of.
Click to expand...
Click to collapse
defroster said:
has anyone tried to repair this?
Click to expand...
Click to collapse
As much as it freaks me out
Pls assist with a DIY ...
As there's No HTC Service in my area
Thanks in advance
aseems said:
As much as it freaks me out
Pls assist with a DIY ...
As there's No HTC Service in my area
Thanks in advance
Click to expand...
Click to collapse
A DIY can not be too difficult and you may be best to search YouTube. It can not be too terribly difficult as long as you can open it up and remove any connecting ribbons (I've had to replace my girlfriends iPhone digitizer due to phone falling out of back pocket onto concrete from three+ feet up). As long as you can open it, you're fine. Just going to need to re-seat the button. Good luck!
Greetings,
I had the same power button issue. I was able to wake my phone using the usb cable whenever the screen timed out but otherwise the phone worked 100% of the time in all ways. I got an RMA and label and shot the phone to them in an anti-static wrap with 4 inches of bubble wrap on all sides and foam padding on top of that. The phone was in perfect condition. Well to cut to the chase. I got a quote of 196.00 because they said there was water damage!? I treated that phone better than I treat my own body! There was no water damage when I sent it in. So one of their folks send me images of a phone that has a broken screen, water damage in the base usb port and no inscription. Interestingly all of the angles avoided showing the ein or s/n. My phone has a laser etched inscription with my name and a couple of bible verses. So what am I supposed to do here? Pay another 196 for an 800 dollar phone that had nothing wrong but a power switch? I am a T-Mobile customer and an Android developer in good standing. What the heck!? Can anyone give me a suggestion on how to get this squared away? My only other option is to send them $28 to get the phone back with the same power button issue. It's even under warranty until Jan 28th.
aseems said:
As much as it freaks me out
Pls assist with a DIY ...
As there's No HTC Service in my area
Thanks in advance
Click to expand...
Click to collapse
why dont you contact htc of a nearby country and send them the phone? i know it is being done. of course you will have to arrange for the transport but it's still worth a shot imo
Here....
http://forum.xda-developers.com/showthread.php?t=687397&page=3
Does anyone know if htc india supports the nexus one for after sales service

Categories

Resources