Related
When I press(with a bit more force) on the left side I hear creaking noise, is that normal or not?
I don't have raised glass problem.
jaroslavj said:
When I press(with a bit more force) on the left side I hear creaking noise, is that normal or not?
I don't have raised glass problem.
Click to expand...
Click to collapse
I have 2 Nexus 7. My Nexus 7 has a minor screen lift, but it's not noticeable. But yea it has the creaking noise near the upper left area. But then again I shouldn't like be putting that much force on the screen so I'm not too worried. My sister's Nexus 7 has no issues with either.
One of the mine did but it seems okay. That's why I think it is the back cover. Because of mine would squeak only if I held it from the back in certain areas. If I held if from another place on the back it wouldn't squeak like holding it from the other side and pushing down then the squeak would be gone. Mine usually would squeak right where the volume of buttons were.
Mine does the same no noticeable screen lift but it will creak if you press too hard on the left side
Sent from my DROID X2 using xda premium
yes.
on the left side of mine its the screen that is raised and creeks. on the right side i think its the back cover that is causing the creeking
I had the creak, it drove me nuts. My screen didn't lift at all. I returned it for a new one with no creak and no screen lift.
ferris2375 said:
I had the creak, it drove me nuts. My screen didn't lift at all. I returned it for a new one with no creak and no screen lift.
Click to expand...
Click to collapse
You had to apply not a lot of pressure if it drove you nuts right? And you RMA yours for that single reason?
jaroslavj said:
You had to apply not a lot of pressure if it drove you nuts right? And you RMA yours for that single reason?
Click to expand...
Click to collapse
I bought mine locally at Sam's, so it was just a matter of taking it back to the store. I bought a new one at Staple's first as they got a new shipment in...of only one.
There was enough movement to make me uncomfortable with it. Not only did it creak on that lower left side with some slight pressure, I could also feel movement when I pressed on the lower left of the screen. Not like squishy movement, just a weird shifting noise.
It's as if the case was a little too large or slightly warped somewhere. I didn't have to press very hard at all to make that sound and it did it naturally if I picked it up from the side. I tend to be OCD so something like that is just one of those things I would fixate on. I also had a dead pixel so the combo was enough to take a trip to Sam's to return it and Staple's for a new one. The difference is night and day with the new one though, it feels so much more sturdy without the noises.
I ordered a case to try and ignore it, but that is still on it's way so the return was kind of an impulse. Honestly if your screen is fine otherwise and you aren't OCD like me, it shouldn't be a deal breaker IMO. Unless a swap is easy, but things could always be worse.
Mine does same, no lift but squeaks with little pressure.
This squeak is because of that black tap that you can see once you open your nexus. At least this was the case with me. The sponge on the top of tape presses the tape when you press the device on left side. I fixed it by removing that foam. I am not recommending anyone to do it as that foam must be there for some reason either to cater for the flex in back cover or something but this was driving me crazy so I removed it. Please don't do it because I am saying this as you might have some different problem. This was my problem and this is how I fix it.
Sent from my Nexus 7 using xda premium
Mine has a slight creak but only when I apply a moderate-high amount of pressure at a certain spot, which I don't feel comfortable doing anyway. Haven't taken the back off but not sure if I will tbh, using a case can alleviate some display issues I.e. screen rising and sight creaks.
Sent from my Nexus 7 using xda premium
Mine has a clicking kind of sound on the left side and the glass depress's about 13/100ths of a MM with little to no force and it was an open box. I will bring mine back as soon as I find a store with another one in stock. I also didn't get the 25$ credit on my Google Play account because the person who bought and returned it took the credit...
My main concern is for dust getting under the glass. If the screen has any kind of travel like mine does I can only assume that it may suck some dust in and under the glass in-between the display and the glass. I don't know if the display is fused to the glass like my Gnex.
I've found that taking the back cover off and putting a single, small piece of electrical tape near the edges in the areas that squeek eliminates the creak. If you have creaking in areas other than the left area where there's screen lift, it's most likely caused by the back cover not fitting perfectly against he device. I put some small pieces of electrical tape in the top right corner and along the bottom right side of my Nexus 7, and it has just about eliminated all creaking.
Mine creaked around the edges til I pressed down hard on them to clip it more securely in place. I've no other issues and the screen is great.
Rik.
Sent from my Nexus 7 using Tapatalk 2
aindow said:
Mine creaked around the edges til I pressed down hard on them to clip it more securely in place. I've no other issues and the screen is great.
Rik.
Sent from my Nexus 7 using Tapatalk 2
Click to expand...
Click to collapse
This is what i done. Worked for me too.
Sent from my Nexus 7 using xda premium
My third replacement has creak with no lift at all.
Sent from my Nexus 7 using xda premium
My second Nexus 7 has no screen lift but the power button clicks loudly when depressed about as loud as a typical space bar. Loud enough that others in my office can tell when I turn the screen on. The vol. rocker does not make the same click sound it sounds and works like the first Nexus 7 I owned. I don't think the louder click from the power button is a big deal and will likely get less loud with use.
Hi!
I got my Nexus 7 yesterday and I dont have the raised glass but I have a creaking noise when pressing down the glass on the left side of the tablet. When I press the glass it creaks and after a second or so you here a popping sound. This is the only issue I have with my Nexus 7. You guys think I should return it and get a replacement or is this normal? It only happen when I press down harder than normal.
Doraso said:
Hi!
I got my Nexus 7 yesterday and I dont have the raised glass but I have a creaking noise when pressing down the glass on the left side of the tablet. When I press the glass it creaks and after a second or so you here a popping sound. This is the only issue I have with my Nexus 7. You guys think I should return it and get a replacement or is this normal? It only happen when I press down harder than normal.
Br D
Click to expand...
Click to collapse
I have the same problem and am trying to decide if its screen lift or just some weird noise. Advice guys?
Same problem - I've had this issue since I got my Nexus 7 two weeks ago and so far nothing terrible has happened.
For anyone having the infamous left side screen lift issue. This includes being able to physically see the glass protruding the silver bezel, screen sponginess, and being able to hear the screen stick/unstick from the adhesive.
After reading this thread http://forum.xda-developers.com/showthread.php?t=1800418 it is apparent the screws are a hair too long. When tightened all the way, they actually can press the screen glass out.
The easiest thing for anyone to try is to just LOOSEN the screws just 1/4 turn. You are loosening the screws so very little, that they will stay snug as far as holding what they are supposed to, but they will no longer push out on the screen glass. I didn't even bother with finding a screw driver, and just used my pocket knife. My screen was raised in the very middle of the left side, so I only loosened the 2 screws directly under the seperation. I suppose this will not work for everyone, but it's so simple and only took me less than 2 mins, you might as well give it a shot. Good luck!
Great thanks
Sent from my Nexus 7 using Tapatalk 2
If you're going to loosen screws you probably want to Loctite them.
http://forum.xda-developers.com/showpost.php?p=29457665&postcount=41
eh hem...what gave you this idea? jk
Just don't overdo it and you'll be fine. No need for loctite, it's only a small turn and the screws are still plenty secure.
---------- Post added at 12:29 AM ---------- Previous post was at 12:28 AM ----------
Loosening the screws in some areas will also help with backlight bleed. If you notice a spot near a screw that is really bright, it's most likely a little too tight.
I found this out by testing different "tightness" adjustments. When I went too far, I noticed back light bleed starting to show, loosen it up a bit and it went away.
This actually worked! So far, anyway. We'll see if it's a permanent fix, but it looks promising.
ferris2375 said:
http://forum.xda-developers.com/showpost.php?p=29457665&postcount=41
eh hem...what gave you this idea? jk
Just don't overdo it and you'll be fine. No need for loctite, it's only a small turn and the screws are still plenty secure.
---------- Post added at 12:29 AM ---------- Previous post was at 12:28 AM ----------
Loosening the screws in some areas will also help with backlight bleed. If you notice a spot near a screw that is really bright, it's most likely a little too tight.
I found this out by testing different "tightness" adjustments. When I went too far, I noticed back light bleed starting to show, loosen it up a bit and it went away.
Click to expand...
Click to collapse
Lol yeah I saw your posts. I mean, that's the same thing I thought of right away. The washers seemed to be a stiff foam, so they compress when screws are tightened. I figured I could loosen them but at the same time keep them snug.
But yeah man good stuff. Did it work for ya?
This.
The washer idea is smart, but for me it caused a more annoying problem. The frame was too thick and pulled the silver trim piece away from the screen and caused a creaking noise at the slightest touch that was way worse than the screen lift.
I just loosened every screw and tightened them back with basically no torque after they stopped turning. All is good now, no creak from the trim and no screen lift, though it's basically flush on he left side
Sent from my Nexus 7
jweitzel24 said:
This.
The washer idea is smart, but for me it caused a more annoying problem. The frame was too thick and pulled the silver trim piece away from the screen and caused a creaking noise at the slightest touch that was way worse than the screen lift.
I just loosened every screw and tightened them back with basically no torque after they stopped turning. All is good now, no creak from the trim and no screen lift, though it's basically flush on he left side
Sent from my Nexus 7
Click to expand...
Click to collapse
Cool. So did you end up loosening the screws then? Meaning, when you re-tightened them, you didn't tighten them as tight as they were from the factory?
Very interesting... I thought the glass was supposed to be flush with the bezel, until I read your comment. After looking at it, the left side of my glass is also flush with the bezel, while the right side glass sits just a little lower.
That's no big deal to me though, as long as my screen is seated properly.
jaycustom said:
Cool. So did you end up loosening the screws then? Meaning, when you re-tightened them, you didn't tighten them as tight as they were from the factory?
Very interesting... I thought the glass was supposed to be flush with the bezel, until I read your comment. After looking at it, the left side of my glass is also flush with the bezel, while the right side glass sits just a little lower.
That's no big deal to me though, as long as my screen is seated properly.
Click to expand...
Click to collapse
Probably a little lighter than factory. Honestly, mine wasn't bad to begin with but like every other ocd person on here, I just couldn't resist opening it up and tightening the screws. At that point, the screen lift started getting worse and I moved on to the other half-dozen or so "fixes" when, it turns out, the screws being too tight was making everything way worse.
But yeah, its been a couple hours now and it still feels real solid. I've got a tpu case on order so regardless I'm done messing with it.
Sent from my Nexus 7 using xda app-developers app
jweitzel24 said:
Probably a little lighter than factory. Honestly, mine wasn't bad to begin with but like every other ocd person on here, I just couldn't resist opening it up and tightening the screws. At that point, the screen lift started getting worse and I moved on to the other half-dozen or so "fixes" when, it turns out, the screws being too tight was making everything way worse.
But yeah, its been a couple hours now and it still feels real solid. I've got a tpu case on order so regardless I'm done messing with it.
Sent from my Nexus 7 using xda app-developers app
Click to expand...
Click to collapse
Cool beans. Luckily, like your N7, mine wasn't bad either.
Couldn't really tell it was lifted by looking at it, but it was the sponginess and that horrible stick/un-stick sound. This is the first fix I tried, and luckily it worked. Let me know how yours turns out, with or without the case..
I simply loosened all screws then tightened them up. Also, Part of a sponge bumper was tucked under a copper shield which I untucked.
Now when I push hard on the left part of the screen I don't get the tacky sound when i unpress it. Also, screen isn't as bulged. In fact you can't even tell anymore.
Neither was a real problem on my n7 but I prefer to make it perfect. This solved everything.
MikeMurphy said:
I simply loosened all screws then tightened them up. Also, Part of a sponge bumper was tucked under a copper shield which I untucked.
Now when I push hard on the left part of the screen I don't get the tacky sound when i unpress it. Also, screen isn't as bulged. In fact you can't even tell anymore.
Neither was a real problem on my n7 but I prefer to make it perfect. This solved everything.
Click to expand...
Click to collapse
Awesome. Mine wasn't bad either, so I just tried for something simple. It seems like the screws may be too long and pressing on the glass, so I thought to just back them off a hair. 2 minutes later the screen is perfect
jaycustom said:
Awesome. Mine wasn't bad either, so I just tried for something simple. It seems like the screws may be too long and pressing on the glass, so I thought to just back them off a hair. 2 minutes later the screen is perfect
Click to expand...
Click to collapse
If you take one of the screws out near the central left and shine a light straight down, you will notice that it is open on the other side as in the the screw can pass through. You will also see a portion of the LCD sticking out underneath those screw holes.
I think the LCD isn't suppose to stick out and get underneath the holes, because otherwise the screws won't hit anything and be tightened all the way. I think for some people without screen lift, the partially sticking out LCD might have been crushed and deformed with the screws or the LCD just isn't sticking out as much.
I've been screwing (pardon the pun) about with this some more today, what I have noticed with mine, is if I take the back off and remove all screws the screen sits perfect, put the screws back in, still seems perfect, clip the back on and the screen now sits above the frame on the left, wondering if mine is an issue with the back plate pushing something out of line.
This worked for a while for me but after it heated up the spongy noise returned. HOWEVER I did notice that loosening the screws did fix the touchscreen issue where it was unresponsive at times.
jaycustom said:
Lol yeah I saw your posts. I mean, that's the same thing I thought of right away. The washers seemed to be a stiff foam, so they compress when screws are tightened. I figured I could loosen them but at the same time keep them snug.
But yeah man good stuff. Did it work for ya?
Click to expand...
Click to collapse
Haha. I was just messing with ya. This is certainly better than adding a shim but I never had the problem. I just wanted to test this out and take my screws back a bit just in case. The other fix is not the way to go as it screws up the casing.
Still no issues though.
Sent from my Nexus 7 using Tapatalk 2
Summerfly said:
If you take one of the screws out near the central left and shine a light straight down, you will notice that it is open on the other side as in the the screw can pass through. You will also see a portion of the LCD sticking out underneath those screw holes.
I think the LCD isn't suppose to stick out and get underneath the holes, because otherwise the screws won't hit anything and be tightened all the way. I think for some people without screen lift, the partially sticking out LCD might have been crushed and deformed with the screws or the LCD just isn't sticking out as much.
Click to expand...
Click to collapse
Thanks for this.
I'm going to open it up again and consider using mini-washers, or something, just to ensure my now-tightened screws are not pressing on the LCD.
Genius. Popped the back off with a knife, loosened the screws down the left side of the screen a quarter of a turn, and now it's perfect - no more squeaking, no more raised screen. Took about 2 mins to do it.
Also, for those who want a decent cover, I bought a Belkin case from PC World yesterday (quite pricey at £30 but I like to try these things out before I buy them rather than just buy online). Even though it's designed for the 7" Samsung Galaxy Tab, it's a near-perfect fit for the Nexus 7. Speaker cut-out is in the wrong place but it doesn't affect the quality noticeably (besides, I hook mine up via Bluetooth to a Jawbone Jambox). Also got myself a sat nav mount and stuck it on the wall next to my bed, so my Nexus 7 is now a handy portable TV
I fixed mine without even getting inside. Just used a blowdryer and heat up the side while holding the screen down. Seemed to stay put and still is.
Simply awesome, completely fixed that annoying screen bulge on the left side!
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Danny80y said:
Ok, so I have had the screen lift problem. It's on the left side worst in the middle. I decided I would take it apart and do the shims between the screws thing. But when I got it open the lift disappeared. So it's a problem with the back pressing up just enough... I noticed a pretty thick piece of foam right on the center left so I removed it. Just replaced the case and tada the tape is holding the screen flat just fine now. Just thought I would pass this on with the other fixes.
Click to expand...
Click to collapse
I noticed last time I opened it that this foam had some compression marks. Likely from pressing against the back. Mine was slightly misaligned, so really only part was compressed. I had the same thought, i.e. remove it. Maybe align it, but it's glued on tight.
So I just removed it. I'll let you know how it turns out in a day or 2.
I also use 3 washers for the top 3 on the left, which helped huge. Hopefully this will make it perfect.
Update Sept 1. This definitely helps. Noticed from pics on another thread that some new models have this foam removed, as shipped. Interesting. Also, on new models, some have screws missing (2 and 4, starting top left). I tried removing screw 2 but when I woke up I noticed creaking and movement at the bezel, when I press my left thumb inwards, which is something I always do. So I put the screw (and washer) back in this morning. Perfect now. But removing this foam was essential, so thanks again.
Makes sense. The screen is dead flat, so it has to be the back case that is separating. Thanks for the info.
Sent from my Nexus 7 using Tapatalk 2
this isn't new and has already been covered already.
dilldoe said:
this isn't new and has already been covered already.
Click to expand...
Click to collapse
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
mike5065 said:
Can you point to where the foam issue was already covered? It was the first I saw.... maybe they have more pointers... Links?
Sent from my Nexus 7 using xda premium
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1781237
http://forum.xda-developers.com/showpost.php?p=29028614&postcount=237
mike5065 said:
Can you point to where the foam issue was already covered?
Click to expand...
Click to collapse
It was covered in the main screen lift thread, which is like 90 pages long and has every possible remedy tested, dissected and mostly debunked. The fact is there are several factors causing the lift and there need to be several solutions to really fix it 100%, and permanently. You can make it better in various ways, one of which is removing that foam, although I believe the foam is there to keep the back from flexing and compressing those metal "prongs", causing them to lose contact. So you might have other problems later without the foam. I probably wouldn't mess with it, personally.
I personally think a workable solution for most N7's with this problem would be to shave that foam down evenly by like 0.3mm, then clamp the screen to the trim and leave it in a hot car like that for a day or so to re-adhere, without the back cover on. Then cool the tablet down and replace the back cover. The hard part is evenly shaving down the foam; it is just a tiny bit too big. But it should be present.
Well I thought I could live with it but the lift is back.... I have also noted that my 8gb gets really poor wifi connection compared to my wife's 16gb. All the clips are still contacting the back plate but I can see no difference in signal with or without the back on. So, I just called google and they are shipping out a new unit for me tomorrow. Hopefully this one is better.
Took the back off to look at screen lift fix. Low & behold 3 screws missing on the LH side of the unit. Also some fingerprints on the copper plates, 2 loose (more than 1 full turn to tighten) screws on the RH side, metal tape/gauze over phone socket loose.
badasscat said:
...So you might have other problems later without the foam...
Click to expand...
Click to collapse
Thanks for all this info. My foam was glued at about 25 degrees off-angle, and clearly compressed at the corner closest to the bezel, so a problem for mine' right from the factory. I didn't get it all off, but most for sure. Once removed, the bulge I had at that point between the bezel and rear case was gone. So was some screen lift' although the washers helped more for that. Not a big win, just another step forward.
I'm still curious why some pics on other thread show no foam, as shipped.
http://forum.xda-developers.com/showthread.php?p=30974024
From my looking, it's in a seemingly non-functional gap, and presses down a wide cable (or something). I earlier traced movement of that cable as the source of 'creaking' I was having, i.e. when it moved against another piece of plastic beside the bezel. I put some lithium where it rubbed and the creaking stopped. Mind you I did that (and the 3 washers precisely tightened) before i removed most of the foam.
My Tf101 was a lot less maintenance than this one. But once done (crossing fingers lol), it's causing my iPad3 to collect dust. This thing just screams. Loving it.
Again, thanks for the info.
Sent from my Nexus 7 using xda premium
A tiny gripe for the perfectionists. But I noticed after a day, that I had a couple of tiny little nicks in the aluminium. As the phone had just been lying on my desk and hadn't been taken outside it must have come that way. I didn't see them at first because they are on the edges and not on the back surface. It is very tiny and it was because it caught the light that I noticed it. I remember when the iPhone 5 came out there were scores of people with chips on the black iPhones that showed silver underneath. This is nowhere near as bad as that....just the light catching the fact that the surface is not quite flat. I had the same with an iPhone 4 a few years ago as well. Seems to me that aluminium is very dingable, even in the factory.
Anyone else notice this?
Mines fine so far, no complaints.
Sent from my HTC One using xda app-developers app
None really had a small black mark but managed to get rid of it quite easily
jonstatt said:
A tiny gripe for the perfectionists. But I noticed after a day, that I had a couple of tiny little nicks in the aluminium. As the phone had just been lying on my desk and hadn't been taken outside it must have come that way. I didn't see them at first because they are on the edges and not on the back surface. It is very tiny and it was because it caught the light that I noticed it. I remember when the iPhone 5 came out there were scores of people with chips on the black iPhones that showed silver underneath. This is nowhere near as bad as that....just the light catching the fact that the surface is not quite flat. I had the same with an iPhone 4 a few years ago as well. Seems to me that aluminium is very dingable, even in the factory.
Anyone else notice this?
Click to expand...
Click to collapse
What colour and is it possible that you post some pictures? I would like to follow this as would a lot of potential buyers Thanks, I have run out of thanks for the day
Please keep us posted about this
markj338 said:
What colour and is it possible that you post some pictures? I would like to follow this as would a lot of potential buyers Thanks, I have run out of thanks for the day
Please keep us posted about this
Click to expand...
Click to collapse
I tried to take a photo of it, but I am going to need someone at home to help me take the picture as its all about getting the light angled correctly so that its clear in the picture. So I will need someone to hold the phone at the right angle so I can get a picture to show. I will try and see if I can get a picture shortly. It is a silver phone, the only colour available right now.
It's not possible to make it 'perfect' so there will be slight defects.
Mine has a tiny little mark on the top that unless you really look for it in certain light its not possible to really see.
Unless there's a real dent or chip on the casing, it shouldn't be a problem. I know it can annoy perfectionists but man, that is aluminium, it is understandable (to an extent, of course)
yep, my silver came with tiny nicks..could feel them when i ran my fingers down the side.not there now [3 days later], maybe 'ironed' out lol
lezduur said:
yep, my silver came with tiny nicks..could feel them when i ran my fingers down the side.not there now [3 days later], maybe 'ironed' out lol
Click to expand...
Click to collapse
Haha...I hope the metal is not SO soft such that it would be possible!
I have wondered if a fingernail is able to nick the edges of the metal. The anodising is only on the back surface. So the bevelled edges will be more suceptible. It is the edge where I noticed a couple of tiny nicks.
I was reading that a fingernal has a hardness of 2.5 (on some scale that I forget the name of). And aluminium is 2.5-3. This would suggest a fingernail striking the edge of the phone could put a nick it. But I am not willing to try intentionally to do so!
jonstatt said:
Haha...I hope the metal is not SO soft such that it would be possible!
I have wondered if a fingernail is able to nick the edges of the metal. The anodising is only on the back surface. So the bevelled edges will be more suceptible. It is the edge where I noticed a couple of tiny nicks.
I was reading that a fingernal has a hardness of 2.5 (on some scale that I forget the name of). And aluminium is 2.5-3. This would suggest a fingernail striking the edge of the phone could put a nick it. But I am not willing to try intentionally to do so!
Click to expand...
Click to collapse
Mohs scale! Yeah, they do overlap on the hardness scale, and nails have a history of being able to scratch aluminum (take Macbooks, for instance).
Yeah my wife came in the room yesterday and said when she pressed the power button, her finger nail scratched the silver lightly. looks like someones drawn a line with a lead pencil by the power button now. might try to buff it out but afraid if i wear the area down it will all go a dull grey.
jcb1985 said:
Yeah my wife came in the room yesterday and said when she pressed the power button, her finger nail scratched the silver lightly. looks like someones drawn a line with a lead pencil by the power button now. might try to buff it out but afraid if i wear the area down it will all go a dull grey.
Click to expand...
Click to collapse
Note to self: Don't be lazy about cutting your nails once you get this phone.
Good call! :good:
jcb1985 said:
Yeah my wife came in the room yesterday and said when she pressed the power button, her finger nail scratched the
Click to expand...
Click to collapse
My wife has damaged three buttons on 2 DAB radios and one remote control by that method.
Not even necessary to use a fingernail to operate the buttons, either.
jcb1985 said:
Yeah my wife came in the room yesterday and said when she pressed the power button, her finger nail scratched the silver lightly. looks like someones drawn a line with a lead pencil by the power button now. might try to buff it out but afraid if i wear the area down it will all go a dull grey.
Click to expand...
Click to collapse
Rule number 1: never let your wife come anywhere near your phone :silly:
compact_bijou said:
My wife has damaged three buttons on 2 DAB radios and one remote control by that method.
Not even necessary to use a fingernail to operate the buttons, either.
Click to expand...
Click to collapse
Have you ever tried growing your nails out super long? The pads of your fingers begin to cease to exist. :laugh:
This is weird. And yes aluminum does indeed has a weak mohs scale and that's the main reason why they anodize it. Now when anodized the mohs scale increases to 9 so how would a fingernail even scratch that?
i can assure you that it does scratch with false fingernails regardless of any specifications.
Riyal said:
This is weird. And yes aluminum does indeed has a weak mohs scale and that's the main reason why they anodize it. Now when anodized the mohs scale increases to 9 so how would a fingernail even scratch that?
Click to expand...
Click to collapse
I dont believe all of the aluminium is anodised though. The back surface certainly is. But there is a bevelled edge which is almost shiny like a mirror, and I think that area is not treated and is also where I found a couple of tiny nicks (seen when angled under a spotlight) out of the box. It is unfortunately also the most likely bit to be hit knocked, swiped with a fingernail etc.
jonstatt said:
I dont believe all of the aluminium is anodised though. The back surface certainly is. But there is a bevelled edge which is almost shiny like a mirror, and I think that area is not treated and is also where I found a couple of tiny nicks (seen when angled under a spotlight) out of the box. It is unfortunately also the most likely bit to be hit knocked, swiped with a fingernail etc.
Click to expand...
Click to collapse
Could you post a picture of that bevelled edge? I'm not sure what you're saying but HTC One is unibody. And when you anodize aluminum you submerge the whole body into a solution. So it's quite impossible that some parts get's anodized and some aren't.
I guess I have to cut all my nails b4 buying it lmao
Sent from my GT-I9300 using Tapatalk 2
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
thats a good idea, itll be great to know if the speaker grills are repleacable, as they are slightly raised on most phones
I'm just worried incase I order the replacment parts and they are not the same quality as the real HTC One parts. Is there a site that sells genuine parts? They would need to ship to the UK for me though...
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
couped said:
Are you out of your mind?
If you are, I'd recommend sandpaper tape and some spray paint. That would probably be easier than disassembly. Maybe even some black nail polish.
Sent from my HTC One using xda premium
Click to expand...
Click to collapse
I dont think it will be as bad as you think, this is the video I was talking about:
http://youtu.be/KwE9PGDnlvs?t=1m51s
I know the top may be more difficult to get off because of the camera and I think I will wait a few more months to see if anyone does drop their One and the top part pops off... But it would be interesting to know because this could be useful to those who get any real bad damage to their speaker grills...
The speaker grills are glued to the housing, Removing them shouldn't be hard
Do it and get us some pics
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
robt772000 said:
I'm doing it. Are you sure about the glue? I also started a thread about it a couple of days ago.
Click to expand...
Click to collapse
The bottom one is definitely glued, I am not sure about the top one though
Im interested...
Barca009 said:
Ok so I have the silver HTC One and as much as I love it, I can't help but think the front would look bad-ass with the black speaker grills...
I was wondering if anyone has any experience replacing their speaker grills, I remember seeing a drop test video and it popped off. The guy in the video mentioned how it didn't clip back on, it was glued on.
I think if it was easy enough to get a stanley blade in between the grill and the plastic it could just pop off (mine has a gap so it could be quite easy) then it would also help in the future if any scratches happen, just to replace them again...
Thoughts?
Click to expand...
Click to collapse
I agree that the black would look pretty cool. Let us know how this turns out! and take pictures of the process. I myself am curious whats behind the top grill, my speaker on the top is starting to crackle horribly i want to know if it would be possible to replace.
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Etradesupply.com sells almost everything for HTC one just so everyone knows if they didn't, u also have a tiny chip in my lower speaker grill, but my case hides it for now so I'm not super worried, but I would love to know if this is possible!!
Sent from my HTC One using xda premium
The grills and the SIM tray are about the only things you can replace. They sell screens, but there is no realistic way to replace them. Even if you could open the phone without marking it, putting it back together is almost impossible.
rovex said:
One of mine (the bottom grill) has a small chip in it that really annoys me, so i have ordered a new set. Postage to the UK is quite expensive, but the total was only £24. Not that bad considering its an original part I guess.
Removing the grills shouldnt be too hard, just heat them up with a hot air gun, being careful not to 'cook' the phone and carefully prise the grill up. The gap most people have in the case may be a help here. The new one should just press on. Warm it up, press it down and hold it firmly until cool, with a clamp or strong bulldog clip if you can.
Click to expand...
Click to collapse
Just for clarification, did you order this from etrade supply? do you have it yet and how is the quality...?
Regards
Zak
Etradesupply quality is very good. I order parts from them and never have an issue.
Heat gun or hair dryer to loosen up the glue should help.
Sent from my HTC One using xda app-developers app
Curious to see if you went through with this.
Sent from my HTC One using xda premium
I bought some etrade silver speaker grills but no longer need them.
If possible please share the whole process heating , removing and fixing the top and bottom speaker grill. Thanks !
Sent from my HTC One using xda app-developers app
Just a tip, do not "paint" the grill. It's impossible to do without stuffing up the holes anyway.. And paint does not stick to aluminium.
You need to anodise aluminium.
Google how to do it but in a nutshell..
1) chemically clean existing aluminium to remove all traces of colour /surface protection. 2)Anodise it to required colour or clear colour
This not only gives you the look you want but makes the surface very hard.
Anodising also is not "on" the surface but part of it so it won't scratch off, block holes etc.
Bare aluminium is very soft and WILL oxidise and go dull. Apart from living in a vacuum or learning to breathe argon gas, you can't stop it.
Anodising MAKES aluminium oxidise and then fill the surface with a dye. This prevents further oxidisation.
Cheers, Marty
Sent from my HTC One using Tapatalk 4 Beta
any luck with replacing the speaker grills?
Just a heads up
I asked about this a different thread and one of the people that replied told me that only the bottom grill is glued in. He said the top is actually screwed in from the back before the back cover is put on. I cant confirm if he was correct, but still good info for anyone planning to try something like this. Can anyone confirm that has purchased these if there are threads in the top grill for it to be screw in?