[Q] nvfalsh problem. can't enter apx mode - LG Optimus 2x

I'm currently using Topogigi ICS 28G.(using new bootloader)
it can boot the rom, enter cwm normally.
but the problem is it can't enter apx mode when I connect it to pc.
after I press vol+ and vol- while connecting it to pc, the screen flash for one second and nothing happen.
the pc not detecting the phone.
wish to try cm10 and need to go back to oldbootloader by nvflash.
anyone has the same problem and solution for it ?
or are there any way to change bootloader without using nvflash ?
btw, I'm sure the cable and pc is not the culprit.
I try to enter apx mode using my friend o2x and it done flawlessly. but not my o2x.:crying:

aris.syah said:
I'm currently using Topogigi ICS 28G.(using new bootloader)
it can boot the rom, enter cwm normally.
but the problem is it can't enter apx mode when I connect it to pc.
after I press vol+ and vol- while connecting it to pc, the screen flash for one second and nothing happen.
the pc not detecting the phone.
wish to try cm10 and need to go back to oldbootloader by nvflash.
anyone has the same problem and solution for it ?
or are there any way to change bootloader without using nvflash ?
btw, I'm sure the cable and pc is not the culprit.
I try to enter apx mode using my friend o2x and it done flawlessly. but not my o2x.:crying:
Click to expand...
Click to collapse
try to do the installing the apx drivers again...restart the computer and then it will work
Hope it helps

aris.syah said:
I'm currently using Topogigi ICS 28G.(using new bootloader)
it can boot the rom, enter cwm normally.
but the problem is it can't enter apx mode when I connect it to pc.
after I press vol+ and vol- while connecting it to pc, the screen flash for one second and nothing happen.
the pc not detecting the phone.
wish to try cm10 and need to go back to oldbootloader by nvflash.
anyone has the same problem and solution for it ?
or are there any way to change bootloader without using nvflash ?
btw, I'm sure the cable and pc is not the culprit.
I try to enter apx mode using my friend o2x and it done flawlessly. but not my o2x.:crying:
Click to expand...
Click to collapse
Go to the recovery, wipe data/Factory reset.
Then reboot. switch it off. Take out the battery. Press the vol- and vol+ button, then put the USB cable.
It should work.

Solution found !
Jishnu Sur said:
Go to the recovery, wipe data/Factory reset.
Then reboot. switch it off. Take out the battery. Press the vol- and vol+ button, then put the USB cable.
It should work.
Click to expand...
Click to collapse
Thanks !
It work !
:highfive::victory:

aris.syah said:
Thanks !
It work !
:highfive::victory:
Click to expand...
Click to collapse
Good to hear that..

Related

Lgp990 stuck at logo screen, not detected by windows

Hi there, I'm new here but I have been following this forum for a long time.
Here's my problem:
I own a LGP990 with DJANGO rom. apart from the random stuck in the DJANGO loading screen which required me to reinstall it, it was all working fine.
Until yesterday, when I plugged it to recharge. The battery charged for a while and then got stuck for hours when almost done.
I unplugged it and try to turn it on but since that moment it always gets stuck at LG logo screen and when plugged it doesn't display any battery charging. I then tried to start recovery to reinstall from zip as I did every time it got stuck in the django loading screen, but recovery does not start.
No problem, I thought, lets smartflash/nvflash a stock rom and i'm good to go. Wrong, the phone won't even get recognized by windows, though I installed the driver several times (disabling driver signature as well) and running it as admin; i tried different driver versions, different usb cables... It does not even play that background sound when plugging usb devices...
I'm using windows 7 32bit.
That's it, I have ran out of ideas... anyone got one? (besides sending it to assistance, since warranty is voided)
little edit: whenever i plug the battery the phone start by itself!
gaernik said:
Hi there, I'm new here but I have been following this forum for a long time.
Here's my problem:
I own a LGP990 with DJANGO rom. apart from the random stuck in the DJANGO loading screen which required me to reinstall it, it was all working fine.
Until yesterday, when I plugged it to recharge. The battery charged for a while and then got stuck for hours when almost done.
I unplugged it and try to turn it on but since that moment it always gets stuck at LG logo screen and when plugged it doesn't display any battery charging. I then tried to start recovery to reinstall from zip as I did every time it got stuck in the django loading screen, but recovery does not start.
No problem, I thought, lets smartflash/nvflash a stock rom and i'm good to go. Wrong, the phone won't even get recognized by windows, though I installed the driver several times (disabling driver signature as well) and running it as admin; i tried different driver versions, different usb cables... It does not even play that background sound when plugging usb devices...
I'm using windows 7 32bit.
That's it, I have ran out of ideas... anyone got one? (besides sending it to assistance, since warranty is voided)
little edit: whenever i plug the battery the phone start by itself!
Click to expand...
Click to collapse
thats an issue I had, power button is making funny games, to enter recovery keep the vol- button pressed before you return the battery.
It always worked for me. let me know if it works.
this is what u have to do man...
http://www.ibtimes.co.uk/articles/40...timus-p990.htm
http://androidadvices.com/unbrick-lg...hone-tutorial/
http://progmaq.es/cm10/progmaq-defau...10-20121105.7z
http://progmaq.es/cm10/progmaq-defau...10-20121105.7z
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: http://bayfiles.com/file/yKZL/eGZ31A/driver.rar The pack includes the APX driver (folder driver)
http://www.putlocker.com/file/4CEDEB7E0893B6F1
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
massimo69 said:
thats an issue I had, power button is making funny games, to enter recovery keep the vol- button pressed before you return the battery.
It always worked for me. let me know if it works.
Click to expand...
Click to collapse
what do you mean before you return the battery? i kept vol- button before removing and then plugging it to the usb but still not detecting
interr said:
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: The pack includes the APX driver (folder driver)
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
Click to expand...
Click to collapse
4/6 of your link are broken dude
gaernik said:
what do you mean before you return the battery? i kept vol- button before removing and then plugging it to the usb but still not detecting
Click to expand...
Click to collapse
I meant to enter recovery. If your phone turns on when you put in the battery, the power button is stuck in a connected position so to enter recovery remove the battery, press the vol- and then insert the battery. If you get your phone to enter recovery and reflash the rom I will tell you what to try to fix the issue.
1.)remove battery
2.)press volume - and volume +
3.)connect phone to pc via usb
4.)download apx driver
5.)(go to device manager install manually apx driver, select the folder where you downloaded and extracted apx ini driver file
6.)flash using nvflash
7.)enjoy.
massimo69 said:
I meant to enter recovery. If your phone turns on when you put in the battery, the power button is stuck in a connected position so to enter recovery remove the battery, press the vol- and then insert the battery. If you get your phone to enter recovery and reflash the rom I will tell you what to try to fix the issue.
Click to expand...
Click to collapse
doing as you said brings me to the "s/w upgrading" screen, not into recovery
wawyed said:
1.)remove battery
2.)press volume - and volume +
3.)connect phone to pc via usb
4.)download apx driver
5.)(go to device manager install manually apx driver, select the folder where you downloaded and extracted apx ini driver file
6.)flash using nvflash
7.)enjoy.
Click to expand...
Click to collapse
problem is that nvflash says "no usb device found" and phone does not appear in device manager
gaernik said:
doing as you said brings me to the "s/w upgrading" screen, not into recovery
Click to expand...
Click to collapse
thats because you have your usb connected
massimo69 said:
thats because you have your usb connected
Click to expand...
Click to collapse
it says so even with usb disconnected :|
gaernik said:
it says so even with usb disconnected :|
Click to expand...
Click to collapse
Then use the AIO toolkit to smartflash a new rom
massimo69 said:
Then use the AIO toolkit to smartflash a new rom
Click to expand...
Click to collapse
as I said earlier, nvflash/aio toolkit give me a "usb device not found" error
gaernik said:
doing as you said brings me to the "s/w upgrading" screen, not into recovery
problem is that nvflash says "no usb device found" and phone does not appear in device manager
Click to expand...
Click to collapse
if you can enter s/w upgrading then you can use smartflash to flash a new rom.
gaernik said:
as I said earlier, nvflash/aio toolkit give me a "usb device not found" error
Click to expand...
Click to collapse
in AIO you have an option to smartflash roms not nvflash. You need to unpack a KDZ rom and install the ROM via smartflash
all the instructions are in the op of the AIO toolkit
the problem still remains, no phone detected and no com port appears in smartflash...
gaernik said:
the problem still remains, no phone detected and no com port appears in smartflash...
Click to expand...
Click to collapse
mmmmhhhhh..... change usb port, change cable, reinstall the drivers. other than that I am at loss
AIO tool has an option to install Nvflash driver. Its the last option in a different color.
Or you could try to reinstall LG driver. I just downloaded the latest driver from lg support tool today. It works fine.
And be noted that you have to hold down both volume up and down while plugging the USB cable to enter nvflash mode. Holding vol down while plugging the cable in will enter boot loader mode which is not the same thing. Remember to remove the battery first of all.
Sent from my LG-P990 using xda premium
massimo69 said:
mmmmhhhhh..... change usb port, change cable, reinstall the drivers. other than that I am at loss
Click to expand...
Click to collapse
done all of that, nothing worked...
mintjustin said:
AIO tool has an option to install Nvflash driver. Its the last option in a different color.
Or you could try to reinstall LG driver. I just downloaded the latest driver from lg support tool today. It works fine.
And be noted that you have to hold down both volume up and down while plugging the USB cable to enter nvflash mode. Holding vol down while plugging the cable in will enter boot loader mode which is not the same thing. Remember to remove the battery first of all.
Sent from my LG-P990 using xda premium
Click to expand...
Click to collapse
installed the driver from support tool but still cant get it recognized neither by smartflash nor nvflash
http://www.ibtimes.co.uk/articles/408044/20121124/unbrick-tool-lg-optimus-p990.htm
http://androidadvices.com/unbrick-lg-optimus-2x-p990-android-phone-tutorial/
http://progmaq.es/cm10/progmaq-default-cm-10-20121105.7z
http://progmaq.es/cm10/progmaq-default-cm-10-20121105.7z
The flasher with NVFlash clears all memory, including the Internal SD., so make a backup if u can..
Download this file: http://bayfiles.com/file/yKZL/eGZ31A/driver.rar The pack includes the APX driver (folder driver) and install the drivers
http://www.putlocker.com/file/4CEDEB7E0893B6F1
1.- Remove the battery to the phone.
2.- Press and hold Vol- and Vol+ and without releasing the 2 keys connect the USB cable to the PC
3.- Go to the progmaq-default-cm-10-20121105 folder and run flash icon... folow instruction., wait wait wait Enjoy!
guys I appreciate all your help but nothing worked. still windows does not detect it, I even plugged to a pc that used to see it :|
lg optimus 2x ics root
gaernik said:
guys I appreciate all your help but nothing worked. still windows does not detect it, I even plugged to a pc that used to see it :|
Click to expand...
Click to collapse
hey...ur problem solved??

[Q] Optimus 4X HD full brick

I tried to put the CM10 on my phone, after installing the zip in recovery mode, I rebooted the device and it never returned to start. Does not show a single light. Do not enter in any way with any combination. When I connect by usb the only thing that appears in device manager is "apx device." Already tried so many things and nothing worked.
anyone have any idea what's going on?
by the way, I tried a lot here in xda before opening a thread.
is your bl unlocked?
Rudjgaard said:
is your bl unlocked?
Click to expand...
Click to collapse
yes
does it vibrate? does it turn on? can you control it through adb? can you enter sw mode?
Rudjgaard said:
does it vibrate? does it turn on? can you control it through adb? can you enter sw mode?
Click to expand...
Click to collapse
No, no, no and no. the only sign of life when it is connected to the pc. Appears "apx" in device manager.
Yeah you are in apx mode, which is basically the boot section of the nvidia tegra chipset.
You should be able to boot normally by unplugging the phone, remove battery for a few seconds, reinsert and hold power button for about 10 seconds
Also try holding power and vol+ (hold them a while) you should be able to boot into normal recovery
Rudjgaard said:
Yeah you are in apx mode, which is basically the boot section of the nvidia tegra chipset.
You should be able to boot normally by unplugging the phone, remove battery for a few seconds, reinsert and hold power button for about 10 seconds
Click to expand...
Click to collapse
I've try that but dont work.
In device manager the apx device is it properly installed or does it have the triangle?
When it first connected as apx device it probably asked you for drivers, i doubt you installed them.
I don't know if the apx drivers for the 04 are out already, check these terms in xda i know some people have been working on them.
Maybe you can find them here
If the device isn't bricked you are in a situation in which you should be able to flash stuff.
For some this method worked:
Try turn off phone
take battery out
hold vol- and put usb cable into phone
if s/w mode starts put battery in and flash kdz
Otherwise check this thread out
or this
I have to go out and can't follow you for a while, sorry
Rudjgaard said:
In device manager the apx device is it properly installed or does it have the triangle?
When it first connected as apx device it probably asked you for drivers, i doubt you installed them.
I don't know if the apx drivers for the 04 are out already, check these terms in xda i know some people have been working on them.
Maybe you can find them here
If the device isn't bricked you are in a situation in which you should be able to flash stuff.
For some this method worked:
Try turn off phone
take battery out
hold vol- and put usb cable into phone
if s/w mode starts put battery in and flash kdz
Otherwise check this thread out
or this
I have to go out and can't follow you for a while, sorry
Click to expand...
Click to collapse
it have the triangle, but i jus want it in normal mode. I dont want that apx mode so i dont need the drivers. But tks for every thing
condegil said:
it have the triangle, but i jus want it in normal mode. I dont want that apx mode so i dont need the drivers. But tks for every thing
Click to expand...
Click to collapse
The only way for you to get connected in APX is without battery, connect to PC while pressing vol- & vol+.
Anyway... why you want to do that? APX mode doesn't work in JB.
Ok... I got it.
Did you tried to deactivate the APX device in device manager?
You can try to performe the bootloader unlock again (run adb and connect the phone while the program wait for device...)
http://www.4shared.com/rar/HFf4newq/LGO4X-UNLOCK-BOOTLOADER.html (instructions inside).
Or try to get in SW mode by trying untill it works... (connect to PC while pressed vol-).
Any update on the problem?
Rudjgaard said:
Any update on the problem?
Click to expand...
Click to collapse
No, i think what happened was that all the firmware is erased and this naturally gave access to apx that should be hidden by the software. Probably there was some error when I wipe to put the CM10. I see no other explanation.
The phone is actually mine. Already sent it to warranty hoping they'll fix it.
Resuming, the phone went unexpectadly in APX mode and havent found a way of quitting that mode, couldn't boot S/W neither bootloader.
And btw the phone is carrier locked and to be honest I'm not sure if it might be part of the problem or not. Anyway in about two weeks the phone should be back and hopefully fixed. If not I'll check here for some more help guys, thanks for attetion so far

[HELP] Boot loop and Cannot enter recovery/fastboot/flashmode

Guys,
I flashed a stock kernel (.207) through fastboot for relocking bootloader.. I was on CM 10.2 (FXP)
I was planning to flash .207 stock through flashmode after relocking BL
But the phone continuosly bootloops. It does not stay in fastboot or flashmode for more than 2 secs, so I cant flash the original kernel of CM 10.2
Also, pc says USB device not recognized when I connect in fastboot or flashmode,I have installed all the drivers also.
Please help me out guys, its urgent..
SOLVED:
Tried this method:
"You mean the problem you were facing is, it keeps on bootlooping even you turn it off via yellow button(off button at the back).then you need to do this. First, ready the flash tool ( until it it prompts to connect the phone.) Then open the back cover, you need a stick or a ballpen to be a tool for pressing the button, then put the pen in standing posistion(the tip's up) hold your phone,place the yellow button against the tip of the pen, press the volume down(if im not mistaken for the flashmode). If you follow me right, you will notice that if you push your phone down, the tip of the pen will trigger the button.. Then ready your usb data cable using your other hand but dont insert it in this point... Now press your phone down until it turn off. Hold and press the volume down(dont release it until you see the green light. Count to five so the movements will sync, after 5 release the pen and immediately attach the cable. If your lucky enough, you can do this in first try."
IT WORKED!!! LIFE SAVER! thanks to Aljon!!
Uhm to relock the bootloader you need to install a Stock ROM via Flashtool.. No need to mess with fastboot mode etc etc..
You could try to reflash the boot.img from the FXP you used before.
~~ Regards
mrjraider said:
Uhm to relock the bootloader you need to install a Stock ROM via Flashtool.. No need to mess with fastboot mode etc etc..
You could try to reflash the boot.img from the FXP you used before.
~~ Regards
Click to expand...
Click to collapse
THe problem is my phone does not stay in fastboot or flashmode long enough
It again goes into bootloop
Also my pc says USB not recognized even when I have installed all drivers (both win 7 and 8)
Use another cable? Or USB port
~~Regards

[Q] Z1 won't turn on

Well i've got this problem with a Xperia Z1 from a friend of mine. It's not powering on. If i press the power button the phone won't turn on. It can enter fastboot but that is everything. The phone is fully charged because that's the only thing that works so far beside the fastboot. It's on stock firmware no custom ROM. Maybe that you people of XDA have the solution i hope so or experienced the same problem and that it is fixable.
Greetings,
Kyrindia
kyrindia said:
Well i've got this problem with a Xperia Z1 from a friend of mine. It's not powering on. If i press the power button the phone won't turn on. It can enter fastboot but that is everything. The phone is fully charged because that's the only thing that works so far beside the fastboot. It's on stock firmware no custom ROM. Maybe that you people of XDA have the solution i hope so or experienced the same problem and that it is fixable.
Greetings,
Kyrindia
Click to expand...
Click to collapse
it is fixable, its very easy: just flash a stock ftf via flashtool. Tutorials can be found here on xda, just google
mo120697 said:
it is fixable, its very easy: just flash a stock ftf via flashtool. Tutorials can be found here on xda, just google
Click to expand...
Click to collapse
Well i've tried that to. But when i plug in the USB cable and press the volume down button it shows the Sony screen and then it goes to charging mode and that's it...... So what coud else be the possible solution? If you want i can make a video of it
kyrindia said:
Well i've tried that to. But when i plug in the USB cable and press the volume down button it shows the Sony screen and then it goes to charging mode and that's it...... So what coud else be the possible solution? If you want i can make a video of it
Click to expand...
Click to collapse
I Had a similar issue, my volume up button got stuck, causing it to always boot in fastboot.
Power up phone, connect to pc, install driver, then run fastboot on your pc and run:
Code:
fastboot continue
Let me know if it helps!
Brainpower said:
I Had a similar issue, my volume up button got stuck, causing it to always boot in fastboot.
Power up phone, connect to pc, install driver, then run fastboot on your pc and run:
Code:
fastboot continue
Let me know if it helps!
Click to expand...
Click to collapse
Thanks for this
Code:
fastboot continue
didn't work but fastboot reboot worked. So i've managed to boot the device and when it was booted. I found out that the power button and the volume down button aren't working! So what is the solution to this can i reinstall Android and find out if it works again because else my friend needs to boot the phone through fastboot and he has no understanding how this fastboot works so is there an another option or am is screwed? Could you please help me? Because i need to fix his phone for this weekend because he already sold his other phone......
kyrindia said:
Thanks for this
Code:
fastboot continue
didn't work but fastboot reboot worked. So i've managed to boot the device and when it was booted. I found out that the power button and the volume down button aren't working! So what is the solution to this can i reinstall Android and find out if it works again because else my friend needs to boot the phone through fastboot and he has no understanding how this fastboot works so is there an another option or am is screwed? Could you please help me? Because i need to fix his phone for this weekend because he already sold his other phone......
Click to expand...
Click to collapse
Did something happen to the phone?
Like dropped it in some liquid other than water?
Does the camera button still function?
For an android reinstall:
Boot the phone normally and perform a software reinstall using Sony PC Companion, connect it via USB to your pc.
With PCC you can fully reinstall the software on the phone.
http://support.sonymobile.com/gb/tools/pc-companion/
Brainpower said:
Did something happen to the phone?
Like dropped it in some liquid other than water?
Does the camera button still function?
For an android reinstall:
Boot the phone normally and perform a software reinstall using Sony PC Companion, connect it via USB to your pc.
With PCC you can fully reinstall the software on the phone.
http://support.sonymobile.com/gb/tools/pc-companion/
Click to expand...
Click to collapse
The phone screen was replaced recently. The camera button works fine. And i don't know if there was any other liquid then water in the phone or something like that. The last thing that i could try is to reinstall the software and hopefully that works.
Thanks anyway :good:

i dont have download mode ???

strange thing!!!
i try to turn off my note 9 exynos then press power+bixby+volume down together but it dont get to download mode but only bootloop till i release the buttons why?
i didn able to get to download mode with the usb hold the bixby and volume down then plug the usb and it did go to download mode
is my phone not good ?
bubu23 said:
strange thing!!!
i try to turn off my note 9 exynos then press power+bixby+volume down together but it dont get to download mode but only bootloop till i release the buttons why?
i didn able to get to download mode with the usb hold the bixby and volume down then plug the usb and it did go to download mode
is my phone not good ?
Click to expand...
Click to collapse
Why would you wanna go into download-mode?
No: your phone is NOT defective, only there's a new procedure to get your phone in download-mode:
https://forum.xda-developers.com/showpost.php?p=77250579&postcount=1
henklbr said:
Why would you wanna go into download-mode?
No: your phone is NOT defective, only there's a new procedure to get your phone in download-mode:
https://forum.xda-developers.com/showpost.php?p=77250579&postcount=1
Click to expand...
Click to collapse
just wanted to check my bootloader so wanted to go to download mode and in youtube people show just to hold the three combine keys but not working for me
bubu23 said:
just wanted to check my bootloader so wanted to go to download mode and in youtube people show just to hold the three combine keys but not working for me
Click to expand...
Click to collapse
If that's not working,can't you use the ADB command adb reboot bootloader ?
KOLIOSIS said:
If that's not working,can't you use the ADB command adb reboot bootloader ?
Click to expand...
Click to collapse
no my friend it works via usb i say that befor and as i see every body say to get to download mode with usb they call it the new methud dont know why lolll
bubu23 said:
no my friend it works via usb i say that befor and as i see every body say to get to download mode with usb they call it the new methud dont know why lolll
Click to expand...
Click to collapse
OK,how about booting to recovery using this (then use the recovery menu to go to bootloader mode):
https://www.hardreset.info/devices/samsung/samsung-galaxy-note-9/recovery-mode/
KOLIOSIS said:
OK,how about booting to recovery using this (then use the recovery menu to go to bootloader mode):
https://www.hardreset.info/devices/samsung/samsung-galaxy-note-9/recovery-mode/
Click to expand...
Click to collapse
nope i try this before and try to get to bootloader like this but it just start my phone regular lollll i can get to bootloader only with usb why??
bubu23 said:
nope i try this before and try to get to bootloader like this but it just start my phone regular lollll i can get to bootloader only with usb why??
Click to expand...
Click to collapse
I can get to it via recovery on my Note 9,I have no explanation as to why you're having issues.
Perhaps try the method given in post #2 of this thread.
New method now for Note 9 download mode. Power off, hold Bixby+Vol Down and connect USB cable to PC to trigger it.
Can't boot into download mode too....
Australia ver....
shirakani said:
New method now for Note 9 download mode. Power off, hold Bixby+Vol Down and connect USB cable to PC to trigger it.
Click to expand...
Click to collapse
Yip, this works...but tricky combo to hold down Bixby and Vol Down while plugging into USB power...I almost took my device in for fixing because I just could't for the life of me boot into Download mode after encountering the dreaded custom binary error on trying to boot up...

Categories

Resources