So, im with Wind mobile. I rooted and flashed my LG optimus 2x to CM10. When i got into mobile networks it keeps saying error searching for networks. When i try to put in the wind specific APN it doesnt save. It wont let me connect to my mobile network plz help!!!!
pgan13 said:
So, im with Wind mobile. I rooted and flashed my LG optimus 2x to CM10. When i got into mobile networks it keeps saying error searching for networks. When i try to put in the wind specific APN it doesnt save. It wont let me connect to my mobile network plz help!!!!
Click to expand...
Click to collapse
Wind O2X is actually a G2X aka a P999.
The CM10 ROM here is for the P990 which uses a different radio (850/1900 compatible)
If you look in the G2X section RC even posted there himself saying that he wasn't able to get CM10 to recognize the radio in the P999, though he had some good theories.
I'm actually impressed that people were able to get CM10 to boot at all on the P999 - everything works except the cell radio, lol.
edit: I just realized, what I said applies only to Ricardo Cerqueira's official CM10 build. If you downloaded one of the CM10 hackfests, make sure you got a P999-compatible one and also check the RIL.
Here is Ricardo's official statement on getting the cell radio to work in CM10 on the P999:
aremcee said:
I've been trying to get this to work for over half a year, so allow me to point you in the right direction:
At this stage, the problem has nothing to do with the RIL. Zero, zip, nada. You're not barking up the wrong tree, you're in the wrong forest entirely.
The kernel source is not compatible with the radio firmware the p999 has, and is therefore unable to enable the radio in the SPI bus. The main ttyspiX nodes don't answer, and the ptsX mux nodes are completely dead (check dmesg)
Until you get ttyspi0, ttyspi1, and the various ttys (starting with /dev/pts1) to answer, anything else is futile.
Click to expand...
Click to collapse
I dont think that is the problem, because I have tried to instally CM 7 for P999 also and it still give the same problem
pgan13 said:
I dont think that is the problem, because I have tried to instally CM 7 for P999 also and it still give the same problem
Click to expand...
Click to collapse
Ah, if it happened on CM7, then you likely have a RIL and/or baseband issue. I don't know the exact details, but there are solutions on XDA for that, just gotta find them.
Still though, where did you get the CM10? Is it a hackfest build or the port of RC's official P990 ROM?
Not sure, just got it from the cyanogenmod site. cyanogenmod.org
machoman1337 said:
Ah, if it happened on CM7, then you likely have a RIL and/or baseband issue. I don't know the exact details, but there are solutions on XDA for that, just gotta find them.
Still though, where did you get the CM10? Is it a hackfest build or the port of RC's official P990 ROM?
Click to expand...
Click to collapse
pgan13 said:
Not sure, just got it from the cyanogenmod site. cyanogenmod.org
Click to expand...
Click to collapse
Are you referring to CM7 or CM10?
If it's CM7 you downloaded, then GetRIL should be able to solve the problem.
If you downloaded CM10, I'm frankly quite surprised it even booted without any modification, but that's not going to get any cell signal whatsoever, nada.
I am referring to both, but i also tired GetRIL, it is also not working for me.
machoman1337 said:
Are you referring to CM7 or CM10?
If it's CM7 you downloaded, then GetRIL should be able to solve the problem.
If you downloaded CM10, I'm frankly quite surprised it even booted without any modification, but that's not going to get any cell signal whatsoever, nada.
Click to expand...
Click to collapse
Related
Would like to know the stats of the users of this fone..because i'd like to release CFW ports for this device..currently i have the MIUI Variant..would like to know if someone here on XDA with the SU660 would appreciate my work..
Thanks!!
i am a su660 user
eatblueorange said:
i am a su660 user
Click to expand...
Click to collapse
so what firmware are you using right now??
any other more users??
up
cm7 kang by open2x...a lot would appreciate your work as a lot have been searching custom ROM for su660
chupi_24 said:
cm7 kang by open2x...a lot would appreciate your work as a lot have been searching custom ROM for su660
Click to expand...
Click to collapse
nice..i was able to port MIUI on my unit..currently using 2.1.20 since the latest has been found out to have bugs..
any other users who might be interested??
currently porting ICS on my work space.. hope i get successful results..
kairi_zeroblade said:
any other users who might be interested??
currently porting ICS on my work space.. hope i get successful results..
Click to expand...
Click to collapse
I am using latest CM7 kang from code.google.com/p/openstar2x/
eatblueorange said:
I am using latest CM7 kang from code.google.com/p/openstar2x/
Click to expand...
Click to collapse
not interested with CM7 i have temasek kang nighlies ported out but i dont feel liking it..also some devs here are a bit selfish..and i do emphasize it..
kairi_zeroblade said:
Would like to know the stats of the users of this fone..because i'd like to release CFW ports for this device..currently i have the MIUI Variant..would like to know if someone here on XDA with the SU660 would appreciate my work..
Thanks!!
Click to expand...
Click to collapse
I'm using su660.
What is the CFW?
Who can tell me?
hope you successfully ported ICS on SU660...that will ease out a lot of SU660 users problem of finding a custom ROM(those that dont want the stock ROM)
why can't we use "normal" optimus 2x ROMs on this su660 Variant? i got it yesterday and i'm a lil bit disappointed
kairi_zeroblade said:
Would like to know the stats of the users of this fone..because i'd like to release CFW ports for this device..currently i have the MIUI Variant..would like to know if someone here on XDA with the SU660 would appreciate my work..
Thanks!!
Click to expand...
Click to collapse
hi.i would definitely appreciate your work i am having a hard time getting a stable rom on my device. where can i get the miui variant?thanks
I would appreciate ur work too
I have a Su660 korea set. But i'm trying very hard to find the IMEI number for the phone. Could someone tell me where is the IMEI number for it. As i'm trying to unlock my phone to get it to work on a US sim card. Any help will be appreciated.
I have a P990, so this may not apply, but....
The IMEI can usually be found in at least 4 places.
1) A sticker on the box it came in.
2) A sticker underneath the battery.
3) Settings/About Phone/Status/IMEI
4) By dialling *#06#
TrymHansen said:
I have a P990, so this may not apply, but....
The IMEI can usually be found in at least 4 places.
1) A sticker on the box it came in.
2) A sticker underneath the battery.
3) Settings/About Phone/Status/IMEI
4) By dialling *#06#
Click to expand...
Click to collapse
I don't have the box anymore. The sticker underneath the battery do not have it. It only has the S/N which is not the IMEI. Settings and so forth doesn't show it at all which i don't get it why.
Dialing *#06# doesn't work for me too apparently
That is weird. I searched a bit, and several articles dealing with IMEI on the SU660 state you should see it by dialling *#06#.
Stock ROM should use it, CM should use it. Are you running some special ROM or a custom dialler?
EDIT: You can also try some apps, search for "Show IMEI" in Google Play.
Cyanogenmod 9 ICS 4.03 on SU660
This blog help me install Ice Cream Sandwich on my LG SU660.
optimus-android.blogspot.com/2012/03/how-to-install-ice-cream-sandwich-ics.html
Apparently my phone is unlocked but the 3g services is not working. Is there a setting i need to set to get it to work?
eatblueorange said:
This blog help me install Ice Cream Sandwich on my LG SU660.
optimus-android.blogspot.com/2012/03/how-to-install-ice-cream-sandwich-ics.html
Click to expand...
Click to collapse
Thanks this worked for me
Hi Guys,
I'm currently running the lastest CM Nightly and have never changed Baseband or Kernel.
The question is should i? and is there a better rom to be using?
Hi!
I believe you've got a good ROM now. The latest CM nightly is pretty good I think so there is no need to change that. (Although, you could try Temaseks CM7 KANG, but that's just my opinion , link in signature btw)
BB is another story though. You should ask yourself: Do I have good signal and call quality? If so, then there's no need to change it. At least I wouldn't change it. What I would try to change is your RIL (if it's necessary though). Download the GetRIL app on the market and let it check if your RIL and BB match. If they match then keep it that way . If not change it using that app.
Kernels on the other hand are optional. If you want to overclock your CPU, or if you want a ramhack then you should flash a kernel. Right now I believe you've got stock CM kernel on your phone, which is pretty good, but not the best. Take a look at the ETaNa Kernel thread, (link in signature) There you'll find more information about what this kernel does with your phone.
Oh and one more thing, you don't HAVE TO change your rom etc. I mean, it's not like we're forcing you to change it right? When you're happy with what you have right now, why don't you keep it like that? But, it's your choice obviously
mness90 said:
Hi Guys,
I'm currently running the lastest CM Nightly and have never changed Baseband or Kernel.
The question is should i? and is there a better rom to be using?
Click to expand...
Click to collapse
Hello I will always recommend you try if you want to flash the baseband 1120 greatly enhances the quality of the call!
Pascalone19 said:
Hello I will always recommend you try if you want to flash the baseband 1120 greatly enhances the quality of the call!
Click to expand...
Click to collapse
cheers guys, where can i find the latest basebands as my call & signal quality isn't great
I think the first thing you should try (also because it's the easiest thing to do) is to get "GetRIL" app from gmarket or gplay or whatever it's called now and see if your RIL and BB match. If they don't, get the matching RIL and see if that has improved quality. If it has, great, no further action necessary... if it hasn't then you can proceed to experimenting with different BB
mness90 said:
cheers guys, where can i find the latest basebands as my call & signal quality isn't great
Click to expand...
Click to collapse
Here you go:
http://forum.xda-developers.com/showthread.php?t=1500443
Here the baseband see real improvements if known and remembered as they told others to find the right GetRil with RIL.
If you have been good press thanks.
Thank you!
Pascalone19 said:
Here you go:
http://forum.xda-developers.com/showthread.php?t=1500443
Here the baseband see real improvements if known and remembered as they told others to find the right GetRil with RIL.
If you have been good press thanks.
Thank you!
Click to expand...
Click to collapse
Hi mate,
i have flashed this baseband but am only now recieving G connecting instead of H/3G
mness90 said:
Hi mate,
i have flashed this baseband but am only now recieving G connecting instead of H/3G
Click to expand...
Click to collapse
Have you installed the corresponding RIL, which is located in the thread?
mness90 said:
Hi mate,
i have flashed this baseband but am only now recieving G connecting instead of H/3G
Click to expand...
Click to collapse
Also, not every BB works perfectly on every phone, country and provider... So yeah, as said before, first try a matching RIL and then look if you connection improves...
i've got the getril app and its showing that i dont have matching ril and bb but when i downloaded it to be matching and it actually caused me to drop more calls and have other problems,
restored so they arent matching but im getting better reception and generally internet works most of the time.
so my question whats the point of them both supposed to be matching?
LG 2x
Carphone warehouse open UK
unlocked
current ril 0218 (V10b, Europe)
current BB 1035.21_20111120
the app says i should get ril 1120 (v20l)
anyone have any better combo suggestions?
mez90 said:
i've got the getril app and its showing that i dont have matching ril and bb but when i downloaded it to be matching and it actually caused me to drop more calls and have other problems,
restored so they arent matching but im getting better reception and generally internet works most of the time.
so my question whats the point of them both supposed to be matching?
LG 2x
Carphone warehouse open UK
unlocked
current ril 0218 (V10b, Europe)
current BB 1035.21_20111120
the app says i should get ril 1120 (v20l)
anyone have any better combo suggestions?
Click to expand...
Click to collapse
I suggest you just put that in. Nothing will gonna happen. If its worse than before you can put old RIL back anytime.
mez90 said:
i've got the getril app and its showing that i dont have matching ril and bb but when i downloaded it to be matching and it actually caused me to drop more calls and have other problems,
restored so they arent matching but im getting better reception and generally internet works most of the time.
so my question whats the point of them both supposed to be matching?
LG 2x
Carphone warehouse open UK
unlocked
current ril 0218 (V10b, Europe)
current BB 1035.21_20111120
the app says i should get ril 1120 (v20l)
anyone have any better combo suggestions?
Click to expand...
Click to collapse
In the post that I have posted for the baseband are also the RIL to flash!
So, did you try to put this new RIL? Any improvements?
Like SP1996AC and I said, you should have started by changing only the RIL. This is the easiest of the operations and could have fixed your problem.
Like they say in America, you start by picking the low hanging fruit first.
You climbed the tree and found out that the fruit on the top wasn't good... now you have to climb down again and try the other fruit.
jordantr said:
I suggest you just put that in. Nothing will gonna happen. If its worse than before you can put old RIL back anytime.
Click to expand...
Click to collapse
Thanks for the reply. I did try the suggested rail but it was worse which is why I went back to a mismatch. I will try the other combinations but at the moment its working OK so might stick to this until the weekend.
Thanks
Can anyone tell me if its possible to get data network on thrill.
there might be, but unless someone posts it actually working, dont use cm10. when i used it, i had signal the first time. however, after an hour or so, my phone randomly rebooted. after it turned back on, service was gone, and IT KEPT rebooting every 2 minutes or so. also, same goes for jellybean and pacman
hummerh14 said:
Can anyone tell me if its possible to get data network on thrill.
Click to expand...
Click to collapse
It does works for the thrill. You just have to flash bernis u-boot and x-loader. I was using it on my v20p thrill. I switch back to GB because people on the other end of the phone were hearing an echo. If you can live with that it works fine. Just go to the o3d development threads there is a thread that explains how to install everything.
Sent my from nook tablet using android 4.2.1 jb /cm10.1 rom.
billy8362 said:
It does works for the thrill. You just have to flash bernis u-boot and x-loader. I was using it on my v20p thrill. I switch back to GB because people on the other end of the phone were hearing an echo. If you can live with that it works fine. Just go to the o3d development threads there is a thread that explains how to install everything.
Sent my from nook tablet using android 4.2.1 jb /cm10.1 rom.
Click to expand...
Click to collapse
Hey thanks for the response do you think u can link me to the guide for this. To tell the truth this phone has alot of potential just no one who wants to build ice also what do u mean jellybean does that mean there's a jellybean for o3d.
hummerh14 said:
Hey thanks for the response do you think u can link me to the guide for this. To tell the truth this phone has alot of potential just no one who wants to build ice also what do u mean jellybean does that mean there's a jellybean for o3d.
Click to expand...
Click to collapse
hey hummeh,
if it does work, another rom is called jellybam you could try it out. it is an expansion from cm10
tang097 said:
hey hummeh,
if it does work, another rom is called jellybam you could try it out. it is an expansion from cm10
Click to expand...
Click to collapse
have you tried this rom looks amazing but im sort afraid to try it because most roms never seem to work for me.
hummerh14 said:
have you tried this rom looks amazing but im sort afraid to try it because most roms never seem to work for me.
Click to expand...
Click to collapse
i've tried it in the past. it would work the first time, yet when i reboot, i would lose all sort of network and reboot randomly. however, its the same as cm10. so if cm10 works for you, this should work as well
Hey do u have working flash in that ROM u suggested on the other forum.
Sent from my LG-P925 using xda app-developers app
Sent from my LG-P920 using xda app-developers app
Is CM10 critical for you?
Because I installed ICS port by XBSA, samno kernel and v20c baseband and it's amazing, like new phone! (in Canada)
You can find all info in Optimus 3D development section. Our phones are EXACTLY the same, just different basebands. With v20c I have 3G/H in WCDMA 850 and WCDMA 1900.
It's challenging process but it worth it. I can help.
Good luck!
Does the back and search button work because other than that I don't really want it.
hummerh14 said:
Does the back and search button work because other than that I don't really want it.
Click to expand...
Click to collapse
Yes, buttons work as suppose to IF you install custom kernel on top of ROM. I use one made by samno (lots of settings too):
http://forum.xda-developers.com/showthread.php?t=2077071
Hope it will help.
Good luck!
OK what phone do u have a lg thrill or optimus 3d also I heard the back and search button doesn't work with lg thrill and if i t does work do u want to help me.
Ok, my phone was originally LG-P925g with Rogers (Canada) - I'm not sure if it was officially called Thrill since I bought it used. Then I read and realized that it's absolutely the same phone as Optimus 3D (920).
So for last year I was using Prometheus ROM with iBluekernel.
Then I decided to try ICS port from XBSA. And it worked. Lots of hoops to go thrugh but works.
Then I put kernel made by samno (in 3D development section) and that kernel solved button issue. But I got another one - at home I could connect to wifi but couldn't go past router. So today I flashed kernel made by iodak and am happy surfer.
If you just flash xbsa port you will have all 4 buttons, but BACK button works as HOME and SEARCH as BACK. HOME is HOME and SETTINGS is SETTINGS.
I hope it helps.
hummerh14 said:
OK what phone do u have a lg thrill or optimus 3d also I heard the back and search button doesn't work with lg thrill and if i t does work do u want to help me.
Click to expand...
Click to collapse
Goldenmeadow said:
Ok, my phone was originally LG-P925g with Rogers (Canada) - I'm not sure if it was officially called Thrill since I bought it used. Then I read and realized that it's absolutely the same phone as Optimus 3D (920).
So for last year I was using Prometheus ROM with iBluekernel.
Then I decided to try ICS port from XBSA. And it worked. Lots of hoops to go thrugh but works.
Then I put kernel made by samno (in 3D development section) and that kernel solved button issue. But I got another one - at home I could connect to wifi but couldn't go past router. So today I flashed kernel made by iodak and am happy surfer.
If you just flash xbsa port you will have all 4 buttons, but BACK button works as HOME and SEARCH as BACK. HOME is HOME and SETTINGS is SETTINGS.
I hope it helps.
Click to expand...
Click to collapse
So what r u using and how r the buttons also what kernel did u flash that has working WiFi and buttons.
hummerh14 said:
So what r u using and how r the buttons also what kernel did u flash that has working WiFi and buttons.[/QUOTE
Can you help me upgrade to that because im sick of the cm10 breaking wifi and the battery life is terrible
Click to expand...
Click to collapse
I have some wifi issues on CM10.1. I cant seem to connect to my home network. When i type in the WPA key and press connect the network only gets saved and that's it. Connecting to an unsecured network works fine though. I tried connecting to a friends router but still the same problem.
This doesn't happen on sense based roms.
Any more users experiencing this ? Suggestions are welcome.
Thanks.
Nobody ?
zat0x said:
Nobody ?
Click to expand...
Click to collapse
EDIT: Nevermind, I see when you originally posted. Sorry for jumping the gun.
To your question though, have you tried with a different AOSP-based kernel? Also a nightly is an experimental build therefore it stands to reason that they might have broken WiFi in the nightly you're using and it'll be fixed in the next round. This is a risk you run with nightly builds.
unremarked said:
EDIT: Nevermind, I see when you originally posted. Sorry for jumping the gun.
To your question though, have you tried with a different AOSP-based kernel? Also a nightly is an experimental build therefore it stands to reason that they might have broken WiFi in the nightly you're using and it'll be fixed in the next round. This is a risk you run with nightly builds.
Click to expand...
Click to collapse
I tried different nightly's. All the same problems with wifi. But it seems im the only one. I also tried P.A.C. rom, AOKP 4.2.2 and Liquid-JB . Still the same issue.
On your suggestion i tried a different kernels.Thoravukk][AOSP][1-JUNE and teaMsevenAOSP_v12r6|VC didnt make any difference.
I found the problem. It seems its router related. I changed the wifi channel settings from manually to automatic and the problem was solved. Very strange. ( Arcadyan VGV7519)
Since I got my i9070 I tried some roms: Pure Vanilla, LightJB, CM 10.1, CM 10.2, Omni
I read all these roms threads, and everything I found on the General section, and also other GPS posts I found on xda and google.
The thing is that with stock, Pure Vanilla and LightJB I had no problems with GPS, without caring of which stock I´d flashed first.
But when moving to CM 10.1, 10.2 or Omni, GPS just gets crazy. Very few times it fixes without problems, most of the times it takes 10 to 15 minutes to fix and sometimes it doesn´t even fix.
I tried with different gps.conf configurations and nothing changed, also with fasterfix, gps status, gps fix and so on... but it´s the same.
What I´m asking for is, as I´m not a developer and I don´t know anything about coding, is what else appart from gps.conf makes the gps work? Are there any files I can try from other roms to test if by replacing them I can get gps to work?
I´ll be more than happy to test anything to make GPS work stable.
More than Kit Kat, I´ll be very happy to have a custom rom, such as CM, working fully stable for my device.
Thanks indeed.
If gps is working for most of users, maybe it is not ROMs fault. Maybe you should try with some other firmware (other baseband than yours now). And do you wipe cache and dalvik cache? And do factory reset after ROM change? That is a must for avoiding strange problems.
If its a question, then threads always go in Q&A.
Development is for development, no exception.
EDIT - Ive cleaned the thread or edited posts, they were all off topic. No point stating rules when your breaking them yourselves.
Back on topic please
Thanks :good:
Try with other baseband now. See what will be.
P.S. We all would be very happy with fully stable CM, but if you follow anything about CM's - we do not have needed sources. Developers are patching stuff and make it usable as they can...
shut_down said:
Try with other baseband now. See what will be.
Click to expand...
Click to collapse
For Argentina we only have 3 stock roms. I tried with the 3 of them.
If I use another stock rom, will I still have 2g/3g?
BachuArg said:
For Argentina we only have 3 stock roms. I tried with the 3 of them.
If I use another stock rom, will I still have 2g/3g?
Click to expand...
Click to collapse
I am not sure about that. And I remember that phones with firmwares from Argentina had some problems on Omni...
Maybe try with Brasil or some other in your region. Ofcourse do not flash I9070P firmware on I9070 phone, and otherwise.
shut_down said:
I am not sure about that. And I remember that phones with firmwares from Argentina had some problems on Omni...
Click to expand...
Click to collapse
One of them was me. Also Tano and a couple of guys more... The same happened to us with CM 10.1 and 10.2
That´s the reason I made this thread.
Shut_down: thanks for your answers.
Baseband doesn´t have to do only with mobile signal? What I knew is that baseband was for mobile and data signal but GPS is a separate thing. Because of this, we can have no phone signal at all, no A-GPS, but GPS working. Something useful for hiking far from cities for example.
BachuArg said:
...Something useful ...
Click to expand...
Click to collapse
try this method http://forum.xda-developers.com/showthread.php?t=2523667
BachuArg said:
One of them was me. Also Tano and a couple of guys more... The same happened to us with CM 10.1 and 10.2
That´s the reason I made this thread.
Shut_down: thanks for your answers.
Baseband doesn´t have to do only with mobile signal? What I knew is that baseband was for mobile and data signal but GPS is a separate thing. Because of this, we can have no phone signal at all, no A-GPS, but GPS working. Something useful for hiking far from cities for example.
Click to expand...
Click to collapse
Maybe this what I bolded is crucial. Without A-GPS it is working lot slower... I remember on stock before I was waiting long for a fix. But on the other hand, now without internet it is lot faster on CM10.1 than yours...
R_a_z_v_a_n said:
try this method http://forum.xda-developers.com/showthread.php?t=2523667
Click to expand...
Click to collapse
I´ve already try it before, but I´ll try it again now I have CM 10.1 installed back from 0.
Well... aparently this time, it works!!!. More or less 1:30 mins to fix.
Question about this. Doesn´t if fix A-GPS?
shut_down said:
Maybe this what I bolded is crucial. Without A-GPS it is working lot slower... I remember on stock before I was waiting long for a fix. But on the other hand, now without internet it is lot faster on CM10.1 than yours...
Click to expand...
Click to collapse
The thing is that many times I´m in places without mobile signal.
Doesn´t A-GPS work only with phone signal by making a triangulation with antenas?
BachuArg said:
I´ve already try it before, but I´ll try it again now I have CM 10.1 installed back from 0.
Well... aparently this time, it works!!!. More or less 1:30 mins to fix.
Question about this. Doesn´t if fix A-GPS?
The thing is that many times I´m in places without mobile signal.
Doesn´t A-GPS work only with phone signal by making a triangulation with antenas?
Click to expand...
Click to collapse
I am not sure, you can read it here about AGps or on other place...
http://en.wikipedia.org/wiki/Assisted_GPS
OP: have you tried the MIUI ROM?
yehuda2 said:
OP: have you tried the MIUI ROM?
Click to expand...
Click to collapse
Not with this phone, I tried it with the Galaxy I had before. Didn't like MIUI.