Hey guys,
I recently bought a Samsung Galaxy S i9000 and the Amoled screen has some serious issues with colours. It appears that the red part of the screen is messed up and cannot display any true white anymore. This happens in download mode, recovery, even in a custom ROM. It's definitely hardware. This video should explain it:
Yes, this phone is pretty much screwed, and the home key is no longer functional at all now. However, I've fixed the rotation sensor issue, and I've thought about repurposing it at a remote for my XBMC media center
Firstly, has anyone seen this issue with the screen before, and secondly, has anyone fixed it? It may be an internal connector which is loose. Suggestions would be good, otherwise I'll just have to put up with the annoying blue tint.
Cheers!
Anyone? Is this more likely to be the panel itself or a cable? Wondering if it's fixable or maybe the connector could be corroded...
Take it apart, remove the mainboard, and clean the board with Isoprophyl-alcohol. Its a 70% alcohol, here in germany you can buy it in a pharmacy. I use a paintbrush to get electronics clean safly.
And also clean the connectors that go from the phone to the board with the alcohol. I suspect there is some kind of water damage in your phone. Samsungs are realy *****y when it comes to water. Even sweat sometimes is enough to cause problems.
To take it apart you only need to remove the 7 screws under the back cover, pull of the back and the board is just held in place by the connectors.
Try youtube if you get stuck. There are some Galaxy S disassembly videos.
Related
My Droid's touch screen isn't working in the center vertically all the way down. I can still use the 'edges' of the screen. I need to use the middle of the screen for a few things (not transfering stuff over). Is there any way I can 'project' my Droids screen to my computer and click/touch in it to use it?
Thanks in advance for all help. It's appreciated
~mfungah
Edit: This is the original Motorola Droid.
I have the same problem on the right side of my milestone :S
I had the same problem, but from the back arrow upwards, specially when the phone got hot. As my phone was still on the warranty period, I flashed it back to stock and updated it to the official 2.2., took it to an Orange shop and got it back after almost a month: they basically changed the whole top part of the phone (I got a brand new screen )
Repair problem
I had a same failure. The touch panel was bad. I ordered one from eBay. It also came as well put it. It works well. Only so much wrong with me that for some reason the phone stacked in landscape mode, I can't change to portrait mode. What is wrong? I put together something wrong? I do not think so. Everything else goes. (or so it seems)
This has to do with the digitizer (the glass you touch over the top of the LCD you see) being defective or unsealed. This is due to environmental moisture finding its way into the phone and f**king with the electrictal signals sent by touching the screen. There is a 'phantom touch' issue that seems to happen before or during the vertical unresponsiveness, and that can usually be temporarily remedied by firmly pushing your screen downwards (your phone may restart) and taking a blowdryer to your phone until it's just hot enough to be uncomfortable to hold (and no longer take it into the bathroom while you shower). One way or another, you're going to have to replace your digitizer eventually.
Sent from my Droid using XDA App
I had the same problem months ago but it's now fixed.
STEPS:
1. Digitizer I bought from this guy:
http://cgi.ebay.ph/New-Touch-Screen-Digitizer-Motorola-Milestone-A853-/270780531 891?pt=UK_Replacement_Parts_Tools&hash=item3f0bc704b3#ht_2811wt_850
2. Dissasembly Videos (I advice you to watch them repeatedly before dissasembly):
http://www.youtube.com/watch?v=6d7ETMfgq2s
http://www.youtube.com/watch?v=dE81IaQHEHc
3. Phillips screw driver( for dealing with hard screws around the screen): Because I don't want you to use the low quality screw driver supplied with the digitizer.
4. Double sided tape: I got mine from a hardware shop for only P19. Buy a the more expensive tape(P100+) but look for a very thin one! You will use the cheap weak tape to stick some internal parts and use the Hard tape to stick the external casing. EDIT: I just used the cheap one for everything and it's strong enough.
5. PATIENCE: Don't be in a hurry. I even paused from time to time to get a better idea about what to do next. Get the feel of being a perfectionist (that same additude when I applied a screen protector )
That's the guide from me who haven't dissasembled a phone in my entire life but my milestone. So if something bad and technical that happens along the way then my knowledge can't help.. sorry.
Good luck bro!!
Well, I fixed my old broken G1 with new screen, touchscreen panel, case and keyboard.
Now I have 2 issue:
1) Sometimes my touchscreen goes grazy!! If I use the touch test application I see that sometimes when I touch the screen in an area there is another virtual touch in another zone of the screen. I read that it can depend from the current source when I charge the phone.. but I'm going crazy!! I opened my phone 10 times (I thought there was a problem in the cable that link TouchPanel to LCDPanel, because when I lock the cable with the clip it tends anyway to go out from the connector, now I put some scotch tape to fix but the problem is here.. so I think is another problem).
2) My volume rocker doesn't work!!
I bought 2 new keyboard to fix this problem, but no one of that fixed the problem. I thought the first new keyboard had volume keys broken, so I bought another one, but the problem persists!!
Now the Touch problem rarely happens, but the volume rocker is completely unusable..
Someone have experience about G1 assembling/repairing ?
Thanks and sorry for bad english
if you have put in multiple keypads have the same issue i would assume that it is the connection going to the motherboard. just a guess there but its either that or you have had a bunch of faulty keyboards.
only other thing would be a software problem
does the keypad work in recovery (let you go up down throughout the list) ?
as for the touch screen, probably need a new digitizer or flex cable, both are cheap and it sounds like you have the knowhow to replace them.
Ok, but digitizer is new!! screen also is new, and I have bought a total of 4 flex cable because I see that they are fragile (I broke the first I bought).
I tried to change flex cable but the problem remain the same.
The only thing that can be damaged is the LCD cable that links to the flex cable: it has a small cut where the cable have a curve, but the cut don't reaches the contacts (the cable is transparent). I also use some glue and scotch tape to mantein lock the cable.
The digitizer cable is connected to the LCD cable, and then they go to the flex cable that connect them to the motherboard.
The strange thing is that seems a software issue, because if I turn off and than turn on the screen, the problem is fixed for some seconds, minutes and sometimes hours...
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
video:
have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
really it sounds like it isnt the hardware since you appear to know what youre doing. i have a had a few phones that had screen (digitizer) issues and a new rom flashed cured it just fine
since you dont mind putting a few dollars into it, and your familiar with the inside, you can always try to pick up a cheap motherboard or spare phone from ebay or what have you, then swap the motherboard and you could then hopefully find out if it is the hardware or software
nagash91 said:
Another strange thing is the possibility to control the screen with some metal objects from the moment that the virtual touch problem appear (I can control the screen also without touch it, with hand and piece of metal)
Click to expand...
Click to collapse
Huh sounds like you got a cheap digitizer than. Most good digitizers use heat to touch. If it's literally touch, then sounds like its a fake/meh digitizer. i hate the digitizers that aren't heat, but press. I see them all the time in those first samsuck touchscreen phones. And they usually die in a bit. I had a Samsung behold with a screwed up digitizer
demkantor said:
have you tried a factory reset if you think it may be a software issue? if that dosent work you can try install a whole new rom.
Click to expand...
Click to collapse
Yes I flashed 3 or 4 roms after a wipe (I tried also super-wipe.zip), but the problem is here..
The digitizer works well some times, but sometimes get crazy (you can see in the video).
I don't that my new digitizer is fake, but I really don't know!
BTW I'm trying to repair my phone for fun (now I have desire z) and because I am fascinated by my old G1.
PS:
I see another strange issue--
If I touch the screen when the phone is on a table the screen digitizer is not very sensitive and can't take input from fingertips.
If I touch the screen when the phone is in my other hand, the screen digitizer is a lot more sensitive and it take input from fingertips.
My impression is that there is an electric field or something similar that disturbs the digitizer, and when I take the phone in my hand I discharge that field to ground. Also when I turn off the screen, seems that the electric field discharge so when I turn on the screen is ok, but after some seconds the field returns to disturbs the screen.
I really don't know, but is the impression that I have.. something that is not shielded.
Now I'll try to use my phone in airplain mode.
Thanks guys, I'm happy to see that this forum is still very active
Hello,
So I broke my screen on my HTC One and decided to repair, having done so before on previous phones I didn't think it would be a problem. Unfortunately upon installing the new screen all I got was a coloured and white pixel noise. Thinking it was a faulty screen I returned it to the supplier and sent off for a new one from a different seller. The new one has exactly the same issue however so now I think I have to conclude it is some sort of hardware issue, possibly caused by static during repair or something along those lines.
The bugger is that there were no issues with the repair itself, it was taken apart carefully and none of the cables damaged, wiggling or otherwise removing and replacing the ribbon cables that are responsible for the LCD has no effect on the noise pattern at all, it remains constant.
I can tell the ROM is running beneath the surface as it has the feature to turn on the flashlight with a long hold power press, and this still works. So the issue is purely with the processing of the image sent to the LCD.
I am unable to test the original LCD as the original cracks cause it to get too badly damaged to work during the original repair.
So I'm basically wondering if there is anything I can do to try and fix this, is there a part I can replace that deals with the LCD image or anything like that? I have a distinct feeling the phone is buggered, but it would be foolish not to ask the community here before sending it to the grave.
I have just discovered a damaged part on the circuit board just behind where the ribbon cable attaches to the mainboard. It is one of the very tiny little black squares, there is a row of 5 and one had a corner that looked damaged and came away when lightly scraped with a tool.
I think this must be the source of the problem, and I would guess means a new mainboard.
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
Shouldn't have done that, I think you accidentally broke something. I'd send it to a HTC service center. But that's gonna cost you probably.
nah, official repair isn't worth it. The phone is more than 2 years old...
and yes i think i broke something... thats why im asking
You're gonna have to be good with a solder and a couple of tiny wires if you want to revive your phone.
00Nuclear00 said:
Hi
I tried to replace my battery and after assemble it back i only get a black display when turning my m7 on.
I broke this little plastic thing from the display cable off (look in attachment)
Is this thing essential for a working display? (i thought i can fix it with a drop of glue)
Should the display work when the backcover is off the device? Because there are some connectors on the backcover....
cheers
Click to expand...
Click to collapse
You definitively need this clip to be intact so the flex cable sits firmly in place otherwise you'll have bad contact between the cable and the pins.
If you don't want to send to HTC for repair you'll need at least to send it to your local electronic repair shop so someone skilled with the proper soldering tool (not the standard iron you have at home) can replace the connector. BTW some of these clips must be lifted from the cable side and some other from the opposite side of the cable, so next time use tweezers and apply very light force on each side you'll find from what side it must be lifted.
LCD should work fine with the back cover removed, afaik. Connectors in the back cover are often for antennas but I wouldn't recommend to run the phone with antennas disconnected to avoid damaging the radio chips (reflected power).
If you are from the US, you can easily find this connector on ebay for about 10$. I'm sure it won't be that much expensive to repair if you bring the new connector and the phone already disassembled to your local repair shop.
Btw are you sure its only the LCD? When trying to boot the phone can you here the HTC theme or does it vibrate? Recognized by your computer when connected with usb?
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
00Nuclear00 said:
thx for your response
I found an replacement part on ebay but first i have to look for someone who can solder this for me.
When i try to turn it on it only vibrates without a htc theme sound and there is no display reaction.
The other thing i mentioned is that the phone gets very hot in the middle (should be the cpu) where i dont know if it should get that hot.
I have to try the pc connetion again and let you know asap.
Click to expand...
Click to collapse
I'm not really worried about the absence of HTC sound when booting, if your phone is on silent / vibration mode, it will only vibrate when booting. If your computer does detect it once booted, then I guess the broken connector clip is the problem.
---------- Post added at 09:49 AM ---------- Previous post was at 09:27 AM ----------
Here is a video about the connector replacement, it doesn't look that hard to replace but wouldn't recommend to do it yourself if you never soldered electronics before. Soldering isn't that hard but you need some practices and knowledge to make good joints. I don't think your phone motherboard is a good candidate to practices yourself if you never did it before. You'll also need a really tiny tip for your iron, probably a type "L", 50/50 solder + some flux. Flux must be cleaned after use to avoid corrosion. The most difficult when soldering on motherboard, imo, is to find the right temperature. If your iron is to hot, you'll damage your connector. If its not hot enough, solder will take more time to liquefy and some heat will be absorbed by surrounding components which can cause irreversible damage.
Easy fix mate
You don't need to replace the connector, I've done this before, it is just the connector clip that has come off and it goes back on reasonably easily.
You will need a good magnifier.
You will need a good light source.
The phone held securely on its side with the socket pointing up.
Some masking tape on the loose part because it WILL go "ping" into the distance if you don't and you will not find it.
Look at the other connectors to see the proper orientation for the part, mark it with a permanent marker on top and at one end.
The insertion looks difficult, it isn't too bad, keep the part nice and straight and the motion is kind of like clicking it down on the ribbon.
Forget replacing the connector, that is 100 times harder.
If you do lose the loose part I have one or two laying around.
Good luck.
I've got a replacement screen that my friend had in his house. Mine was broken (both the display and the digitizer, the latter was acting very weird). I did the replacement myself, and when I was finally done, I noticed something. The Touch Screen wasn't working (I could see the image but no input was recognized). I tried opening it and checking every single cable to see if there was anything wrong, but there was nothing looking broken or out of place. When I was going to test it, I noticed another very weird thing. It actually works if I keep the back of the phone off (not the back interchangable cover, I mean the back of the phone that is screwed in place). The problem is that this phone has a very annoying design that makes it so the Wi-Fi, Speakers, Camera and some other stuff don't function well with the back plate off, speacially the Wi-Fi.
I trully have no idea what is happening or what is causing the problem with the touch screen, and have no idea why the back plate makes the screen act funny. Can someone please help me figure this out?
Perhaps something in the digitizer's flex cable is shorting with the back panel. Try putting a layer of electrical tape between the flex cable and the back panel.