Related
Hi,
I know that the boot loop scenario is pretty common, but my problem seems bizarre. I recently installed cyanogenmod successfully but I was unhappy with it so I decided to remove it and install a clean version of Sense 5.5. I obviously screwed up somehow.
The problem is that the phone doesn't want to boot up to the normal home screen. Whenever I power the phone on it automatically boots onto the FASTBOOT screen. From there I get a number of different problems, I shall list which options work and which do not; FASTBOOT works, RECOVERY does not (reboots back to FASTBOOT), FACTORY RESET does not work (reboots back to FASTBOOT), SIM LOCK does not work, IMAGE CRC works, SHOW BARCODE works.
When I use FASTBOOT USB I am unable to see my device on my computer also, so I am unable to look inside my SD card or use abd commands.
Here is what the top of HBOOT reads;
*** TAMPERED ***
*** RELOCKED ***
*** Security Warning ***
M7_UL PVT SHIP S-ON RH
HBOOT-1.55.0000
RADIO-4A.21.3263.04
OpenDSP-v32.120.274.0909
OS-3.62.206.1
eMMC-boot 2048MB
Oct 18 2013,00:29:38.0
It seems your boot loader has been relocked. It must have been unlocked for you to install cyanogenmod right?
Which method did you use to install a clean version of Sense? I'm not too familiar with running RUUs but if you want the phone to stay rooted then I would flash a new recovery using fastboot.
I'm running into a similar problem, my HTC One is just like yours, my computer doesn't even read it as a media device and says that there's something wrong (duh), tried running up ADB, redownloaded drivers and I still have no luck.
Sent from my SM-N900T using Tapatalk
JasSingh93 said:
It seems your boot loader has been relocked. It must have been unlocked for you to install cyanogenmod right?
Which method did you use to install a clean version of Sense? I'm not too familiar with running RUUs but if you want the phone to stay rooted then I would flash a new recovery using fastboot.
Click to expand...
Click to collapse
It must have been unlocked. I used ClockworkMod, I deleted the cache and then installed the Sense ROM from my SD card.
I tried to run a RUU but I couldn't because my phone is not being recognized by my computer.
@ hrogers .. Try to load a custom RECOVERY from TWRP and/ or an RUU. executive from HTCguru
Sent from my HTC One using XDA Premium 4 mobile app
dayze0 said:
@ hrogers .. Try to load a custom RECOVERY from TWRP and/ or an RUU. executive from HTCguru
Sent from my HTC One using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Unable to do that due to no connection between phone and computer.
hrogers123 said:
Unable to do that due to no connection between phone and computer.
Click to expand...
Click to collapse
You should be able to send commands to the phone using fastboot USB. Have you checked you have the correct drivers installed and correctly set it up? Tried using a different PC maybe?
Also try starting from scratch, deleting all the PC fastboot files and drivers and re-setup.
I've never had any problems with fastboot, it usually never fails.
JasSingh93 said:
You should be able to send commands to the phone using fastboot USB. Have you checked you have the correct drivers installed and correctly set it up? Tried using a different PC maybe?
Also try starting from scratch, deleting all the PC fastboot files and drivers and re-setup.
I've never had any problems with fastboot, it usually never fails.
Click to expand...
Click to collapse
Wow i'm a dumbass, completely forgot about fastboot commands. Will do that now to see if it fixes the problem.
As the topic says, the phone was bought on ebay-Germany and when received, I found out that the phone was tampered with previously. Seller does not respond to my mail or willing to pay back. The phone is only 1month old with receipt.
So, decided to seek help here. I will appreciate any help to get this fone work. This is what I can say about the phone;
- When I press on the power, it boots directly into Team Win Recovery project V2.6.3.3. I tried to reboot it takes me into further steps that finally switch off the phone. All attempts to actually boot the phone yield no result.
- Again in Recovery, I tried to restore backup (if ever the was any) and it show successfully restore. But on reboot it then shows “no OS installed!”
- I tried connecting on my pc and the phone driver installation failed several time on all usb port on my laptop (I have only one pc, with win8 – my laptop). I decided to uninstalled the htc software and driver I used for my HTC 1X, then reinstalled again. Still the phone could not be recognized.
- On pressing power and vol., the following can be seen including IMEI (from show barcode);
*** TAMPERED ***
*** UNLOCKED ***
M7_UL PVT SHIP S-ON RH
HBOOT-1.55.0000
RADIO-4A.21.3263.04
OpenDSP-v32.120.274.0909
OS-3.62.401.1
eMMC-boot 2048MB
Oct 17 2013, 23:06:14.0
This is all the informations I can provide as of now, since connection with pc has not been successful. I wonder how to get the Token ID if successful connection with pc occurs.
Please help me any way you can. Thank you and Happy new year
htcstone36 said:
As the topic says, the phone was bought on ebay-Germany and when received, I found out that the phone was tampered with previously. Seller does not respond to my mail or willing to pay back. The phone is only 1month old with receipt.
So, decided to seek help here. I will appreciate any help to get this fone work. This is what I can say about the phone;
- When I press on the power, it boots directly into Team Win Recovery project V2.6.3.3. I tried to reboot it takes me into further steps that finally switch off the phone. All attempts to actually boot the phone yield no result.
- Again in Recovery, I tried to restore backup (if ever the was any) and it show successfully restore. But on reboot it then shows “no OS installed!”
- I tried connecting on my pc and the phone driver installation failed several time on all usb port on my laptop (I have only one pc, with win8 – my laptop). I decided to uninstalled the htc software and driver I used for my HTC 1X, then reinstalled again. Still the phone could not be recognized.
- On pressing power and vol., the following can be seen including IMEI (from show barcode);
*** TAMPERED ***
*** UNLOCKED ***
M7_UL PVT SHIP S-ON RH
HBOOT-1.55.0000
RADIO-4A.21.3263.04
OpenDSP-v32.120.274.0909
OS-3.62.401.1
eMMC-boot 2048MB
Oct 17 2013, 23:06:14.0
This is all the informations I can provide as of now, since connection with pc has not been successful. I wonder how to get the Token ID if successful connection with pc occurs.
Please help me any way you can. Thank you and Happy new year
Click to expand...
Click to collapse
you don't need to get the Token ID, your Bootloader says UNLOCKED
You should be able to use ADB commands trough TWRP recovery and you should also be able to mount your sd card via TWRP
Go to this link: http://www.htc1guru.com/downloads/stock-rom-downloads/ and watch the video guide.
download your guru reset for your version (3.62.401.1) here: http://www.htc1guru.com/dld/guru_reset_m7_3-62-401-1-zip/
connect your phone to pc and boot in twrp recovery
mount your sd card
push the .zip file to your sd card
install the zip and reset your phone like in the video guide
are you using windows 8.1 or 8.0 bcause 8.1 have issue with fastboot drivers. Better to do all of this procedure on a win 8.0 or 7 pc.
Looks to me like no ROM on Phone
Hi and happy new year to you too....
After from what I read here it looks to me like there is no Rom installed on the phone.
The phone seems to be wiped therefore boots into recovery on Power On.
Can you access all features of Team Win recovery?
If yes try this:
You will need an OTG cable and a USB Storage for this!!!
Download a Custom Rom, I recommend SD Eragon v21
Put Rom onto your USB Storage plug USB Storage into OTG Cable and Cable into Phone.
Boot into Team Win Recovery
Select "Wipe"
Select "Format Data" type "yes" to continue
Making sure that we format the Phone properly again.
Go Back to Recovery Menu and select "Mount"
Tick "USB-OTG"
Go Back
Select "Install"
Find "usb-otg" on the list; if you cant see it select (Up a Level)
If you have found usb-otg select it and you will see Eragon21 Rom
Swipe to install and follow the prompts.
Once successfully installed reboot phone and hopefully it should work
Let us know how u r going
htcstone36 said:
As the topic says, the phone was bought on ebay-Germany and when received, I found out that the phone was tampered with previously. Seller does not respond to my mail or willing to pay back. The phone is only 1month old with receipt.
So, decided to seek help here. I will appreciate any help to get this fone work. This is what I can say about the phone;
- When I press on the power, it boots directly into Team Win Recovery project V2.6.3.3. I tried to reboot it takes me into further steps that finally switch off the phone. All attempts to actually boot the phone yield no result.
- Again in Recovery, I tried to restore backup (if ever the was any) and it show successfully restore. But on reboot it then shows “no OS installed!”
- I tried connecting on my pc and the phone driver installation failed several time on all usb port on my laptop (I have only one pc, with win8 – my laptop). I decided to uninstalled the htc software and driver I used for my HTC 1X, then reinstalled again. Still the phone could not be recognized.
- On pressing power and vol., the following can be seen including IMEI (from show barcode);
*** TAMPERED ***
*** UNLOCKED ***
M7_UL PVT SHIP S-ON RH
HBOOT-1.55.0000
RADIO-4A.21.3263.04
OpenDSP-v32.120.274.0909
OS-3.62.401.1
eMMC-boot 2048MB
Oct 17 2013, 23:06:14.0
This is all the informations I can provide as of now, since connection with pc has not been successful. I wonder how to get the Token ID if successful connection with pc occurs.
Please help me any way you can. Thank you and Happy new year
Click to expand...
Click to collapse
MotoXoom said:
Hi and happy new year to you too....
After from what I read here it looks to me like there is no Rom installed on the phone.
The phone seems to be wiped therefore boots into recovery on Power On.
Can you access all features of Team Win recovery?
If yes try this:
You will need an OTG cable and a USB Storage for this!!!
Download a Custom Rom, I recommend SD Eragon v21
Put Rom onto your USB Storage plug USB Storage into OTG Cable and Cable into Phone.
Boot into Team Win Recovery
Select "Wipe"
Select "Format Data" type "yes" to continue
Making sure that we format the Phone properly again.
Go Back to Recovery Menu and select "Mount"
Tick "USB-OTG"
Go Back
Select "Install"
Find "usb-otg" on the list; if you cant see it select (Up a Level)
If you have found usb-otg select it and you will see Eragon21 Rom
Swipe to install and follow the prompts.
Once successfully installed reboot phone and hopefully it should work
Let us know how u r going
Click to expand...
Click to collapse
Hello there, i have a very similar problem on my side: http://forum.xda-developers.com/showthread.php?t=2595552
I get to go back to TWRP Recovery who asks me a password everytime. I'm looking forward to get a OTG Cable to try all you told here. But without the password will I be able to do anything?
When TWRP asks you for password try to hit "cancel" and see what happens.
Are you able to get into Recovery once you hit cancel?
Yeeshak said:
Hello there, i have a very similar problem on my side: http://forum.xda-developers.com/showthread.php?t=2595552
I get to go back to TWRP Recovery who asks me a password everytime. I'm looking forward to get a OTG Cable to try all you told here. But without the password will I be able to do anything?
Click to expand...
Click to collapse
MotoXoom said:
When TWRP asks you for password try to hit "cancel" and see what happens.
Are you able to get into Recovery once you hit cancel?
Click to expand...
Click to collapse
Yep I'm, just missing the OTG Cable to install a ROM now
Then you should be all good to go
Yeeshak said:
Yep I'm, just missing the OTG Cable to install a ROM now
Click to expand...
Click to collapse
Thank you very much for the prompt reply to my post. I will be going out soon to get the OTG cable, then try if it works. Will post the result thereafter.
Meanwhile, I will first try the first solution with Guru Reset. Once again thank you.
QUOTE=MotoXoom;49071630]Hi and happy new year to you too....
After from what I read here it looks to me like there is no Rom installed on the phone.
The phone seems to be wiped therefore boots into recovery on Power On.
Can you access all features of Team Win recovery?
If yes try this:
You will need an OTG cable and a USB Storage for this!!!
Download a Custom Rom, I recommend SD Eragon v21
Put Rom onto your USB Storage plug USB Storage into OTG Cable and Cable into Phone.
Boot into Team Win Recovery
Select "Wipe"
Select "Format Data" type "yes" to continue
Making sure that we format the Phone properly again.
Go Back to Recovery Menu and select "Mount"
Tick "USB-OTG"
Go Back
Select "Install"
Find "usb-otg" on the list; if you cant see it select (Up a Level)
If you have found usb-otg select it and you will see Eragon21 Rom
Swipe to install and follow the prompts.
Once successfully installed reboot phone and hopefully it should work
Let us know how u r going [/QUOTE]
i got stuck 2 days ago, i used hansons toolkit in fastboot, and flashed stock recovery, relocked bootloader, and ran the RUU.. all fixed up...
then i unlocked the bootloader.. u might need to go htc dev to get the unlock bootloader
Hi,
I too am having a similar problem but my phone is frozen on the htc logo I can't turn it off i have to wait till it's dead, I can't enter recovery mode plus my laptop won't find the phone when it's connected.
I'm in a rite mess, I just formatted everything before I gave it to my son now I've ruined it for him
Finally, I am happy to announce the result of the solutions provide by Alray and MotoXoom.
First and foremost, my phone has been saved! This is thanks to Alray's Guru reset method proposed in post 2 and MotoXoom for the idea of using a OTG cable mentioned in post 3.
For those who may be facing a similar issue, this is what I did;
The Guru Reset method is very easy if the instruction on the video is follows keenly. Since my pc could not find my phone, I when on to buy an OTG flash drive from Conrad Berlin, also available on ebay.
Initially the flash was not recognised, I then formatted with fat32 and plung-in again to the phone. Voila! it worked. First of all hit on mount and click on usb otg , then click back and hit on install. The rest of the instruction can then be seen on the video on post 2 from Alray.
It is also worth mentioning that at the end of the installation Team win recovery should be reinstall as was deleted be the Guru reset software.
However, I still need further help on how to remove the “ Tampered” on the bootloader screen as well as how to get S-Off. I do not know how to go about this, since I do not have the Token-ID. Is the Token ID not necessary for this? I will appreciate further help. Once again thank you Alray.
N.B.: I still find it difficult to quote a post directly, how is this done?
Since over an hour I am not allow to post anymore and decided to edit the previous message in order to post a message.
I also do not understand this message " To prevent spam on the XDA forums, ALL new users prevented from posting outside links in their messages. After approximately 10 posts, you will be able to post outside links. Thank you for understanding!"
Worst case scenario: flash a RUU (of course one from the phone's region)
RUU will reinstall the whole phone's original rom but you will lose root (you will reroot it later)
htcstone36 said:
Hi alray, I am using win 8.0.
I'm actually trying to use the solution you provided, but then, I am still face with some difficulties. I can't push the zip file into my phone directly without a OTG cable. Only possible with ADB Sideload, which is taking a little longer (over an hour and still on 35%)? Am I doing something wrong?
Moreover, I will like to know how to get the "Tampered“off the screen and change the “S-ON” to S-Off. But before then, first thing first; that is to boot the phone.
Accept my gratitude for the initial solution u provided. Thank you!
Click to expand...
Click to collapse
Push / sideload on usb 2 should take less than 10 min
your stuck restart both the phone and pc and try again
htcstone36 said:
As the topic says, the phone was bought on ebay-Germany and when received, I found out that the phone was tampered with previously. Seller does not respond to my mail or willing to pay back. The phone is only 1month old with receipt.
So, decided to seek help here. I will appreciate any help to get this fone work. This is what I can say about the phone;
- When I press on the power, it boots directly into Team Win Recovery project V2.6.3.3. I tried to reboot it takes me into further steps that finally switch off the phone. All attempts to actually boot the phone yield no result.
- Again in Recovery, I tried to restore backup (if ever the was any) and it show successfully restore. But on reboot it then shows “no OS installed!”
- I tried connecting on my pc and the phone driver installation failed several time on all usb port on my laptop (I have only one pc, with win8 – my laptop). I decided to uninstalled the htc software and driver I used for my HTC 1X, then reinstalled again. Still the phone could not be recognized.
- On pressing power and vol., the following can be seen including IMEI (from show barcode);
*** TAMPERED ***
*** UNLOCKED ***
M7_UL PVT SHIP S-ON RH
HBOOT-1.55.0000
RADIO-4A.21.3263.04
OpenDSP-v32.120.274.0909
OS-3.62.401.1
eMMC-boot 2048MB
Oct 17 2013, 23:06:14.0
This is all the informations I can provide as of now, since connection with pc has not been successful. I wonder how to get the Token ID if successful connection with pc occurs.
Please help me any way you can. Thank you and Happy new year
Click to expand...
Click to collapse
ADB will be your friend. follow everyone elses instructions and you will be fine
Hello,
(my english is not very well, sorry for that)
Because the vibration engine was to loud, i wanted to reset my HTC One (delete root and lock it again) to send it to HTC.
I did something wrong and now my HTC One is in a Boot-Loop.
When i hold the power button and the volume down button i can get into "Menu" with Fastbood. And i can turn it on.
But my PC can't find it anymore. I tried it on 3 different Pc's and one Mac.
The Recovery doesn't work (i come into the boot-loop).
I'm working since 20 working hours to solve this problem, but i can't fix it...
Could you please, please help me?
Thank you very much!
Best wishes
Dakanta said:
Hello,
(my english is not very well, sorry for that)
Because the vibration engine was to loud, i wanted to reset my HTC One (delete root and lock it again) to send it to HTC.
I did something wrong and now my HTC One is in a Boot-Loop.
When i hold the power button and the volume down button i can get into "Menu" with Fastbood. And i can turn it on.
But my PC can't find it anymore. I tried it on 3 different Pc's and one Mac.
The Recovery doesn't work (i come into the boot-loop).
I'm working since 20 working hours to solve this problem, but i can't fix it...
Could you please, please help me?
Thank you very much!
Best wishes
Click to expand...
Click to collapse
reflash twrp 2.6.3.3 via fastboot should let you get back into recovery, then do a full wipe and sideload your rom and install it
xnknown said:
reflash twrp 2.6.3.3 via fastboot should let you get back into recovery, then do a full wipe and sideload your rom and install it
Click to expand...
Click to collapse
Hello xnknown,
but my PC can't find my HTC One in Fastmood.
When I try adb devices it can't be found.
When I try dab devices in boot loop there comes just for a few seconds until my HTC One restarts this message:
List of devices attached
FA34NW902365 device
Thank you
Dakanta said:
Hello xnknown,
but my PC can't find my HTC One in Fastmood.
When I try adb devices it can't be found.
When I try dab devices in boot loop there comes just for a few seconds until my HTC One restarts this message:
List of devices attached
FA34NW902365 device
Thank you
Click to expand...
Click to collapse
Here is what stands in my Fastboot Mode on my HTC One
TAMPERED
UNLOCKED
M7_UL PVT SHIP S-ON RH
HBOOT-1.44.0000
RADIO-4A.20.3263.16
OpenDSP-v26.120.274.0202
eMMC-boot
Apr 12 2013,12:10:45:-1
Dakanta said:
Here is what stands in my Fastboot Mode on my HTC One
TAMPERED
UNLOCKED
M7_UL PVT SHIP S-ON RH
HBOOT-1.44.0000
RADIO-4A.20.3263.16
OpenDSP-v26.120.274.0202
eMMC-boot
Apr 12 2013,12:10:45:-1
Click to expand...
Click to collapse
try fastboot erase cache, u sure u have the htc drivers installed and the adb sdk?
xnknown said:
try fastboot erase cache, u sure u have the htc drivers installed and the adb sdk?
Click to expand...
Click to collapse
Thank you. Fastboot erase cache didn't worked.
I installed the adb SDK and HTC Sync (the drivers are included there, right?) Would my HTC be found in Boot-Loop when I didn't installed the drivers?
List of devices attached
FA34NW902365 device
Or are the drivers in fastboot another thing?
Thank you for your great help!
Dakanta said:
Thank you. Fastboot erase cache didn't worked.
I installed the adb SDK and HTC Sync (the drivers are included there, right?) Would my HTC be found in Boot-Loop when I didn't installed the drivers?
List of devices attached
FA34NW902365 device
Or are the drivers in fastboot another thing?
Thank you for your great help!
Click to expand...
Click to collapse
yes the htc drivers are included in htc sync however you need to uninstall htc sync itself afterwards
socialistic rrbaungm
Thank you.
I should uninstall HTC Sync directly after installation?
Dakanta said:
Thank you.
I should uninstall HTC Sync directly after installation?
Click to expand...
Click to collapse
yes, you should still see your htc drivers in your uninstall program list
xnknown said:
yes, you should still see your htc drivers in your uninstall program list
Click to expand...
Click to collapse
Suddenly my CWM started again :good:
So i played Viper One 2.6 on my One. But Fastboot doesn't work at all.
I'll try to fix my driver problem.... or is there an other way to get back on stock and lock my One?
Can you flash TWRP and then boot into TWRP ?
Also, fastboot only works in fastboot moder in bootloader. Not in recovery and NOT in OS.
ADB works only in recovery and when you are in OS. NOT in fastboot boot mode.
Dakanta said:
Suddenly my CWM started again :good:
So i played Viper One 2.6 on my One. But Fastboot doesn't work at all.
I'll try to fix my driver problem.... or is there an other way to get back on stock and lock my One?
Click to expand...
Click to collapse
well if you want a relatively stock experience i would suggest going with ARHD 51, its basically the same as stock but a little speedier without the bloat
SaHiLzZ said:
Can you flash TWRP and then boot into TWRP ?
Also, fastboot only works in fastboot moder in bootloader. Not in recovery and NOT in OS.
ADB works only in recovery and when you are in OS. NOT in fastboot boot mode.
Click to expand...
Click to collapse
Hey SaHiLzZ,
can I flash TWRP without Fastboot?
If I understand your second sentence right, yes I was in fastboot mode. I obviously got driver problems, i'll try to fix them now.
xnknown said:
well if you want a relatively stock experience i would suggest going with ARHD 51, its basically the same as stock but a little speedier without the bloat
Click to expand...
Click to collapse
Thank you xnknown,
no I have to go to Stock because of warrenty.
My vibration engine is much louder than normal. And my second Mic doesn't work.
I don't know the warranty of your countries, but in Germany it has to be stock when I'll bring it back to my electronics retailer
At the moment i just install all possible in SDK and I hope that it will work.
Thank you for your help
Dakanta said:
Hey SaHiLzZ,
can I flash TWRP without Fastboot?
If I understand your second sentence right, yes I was in fastboot mode. I obviously got driver problems, i'll try to fix them now.
Click to expand...
Click to collapse
Yes you were in fastboot if it says Fastboot USB on your phone. You can flash it once you are in the screen.
fastboot flash recovery (name of recovery)
I will suggest TWRP 2.6.3.3
Then type fastboot erase cache
I was such an Idiot.
I tried to find my Phone with adb devices in adb. The correct command was fastboot devices.
Two days of work because of that little problem :crying: :crying::crying::crying::crying:
Now I'm back on Viper One 2.6 and I'm looking for a Tutorial to bring my One back to Stocke an lock it again.
Thank you!!!
Hey,
i brought my One back on Stock.
But when I update to 4.2.2. the progress always hang up at i think 30%.
I startet it 3 times new, but its always the same failure. I'll keep the One over night on the charger and I hope, that in the morning the One is on 4.2.2 and I can update on 4.4.2.
Did I do something wrong?
And my other problem:
How can I delete the CWM Backup? I don't have root anymore. My SDCard is just 25GB
Thank You !
Hello,
I am pretty sure that I bricked my usb port and there is NO way to solve my problem but just to be sure:
Does anyboidy know if I have a software or a Hardware issue??
No computer recognized my phone. Im 100% sure that it is no driver problem, My computer just say: Unknown device. code:43
My phone was unlocked and rooted, so I tried to flash a stock rom with root-access on my HTC. I thought it could solve my USB-problem, but it did not, Unfortunately I lost my root-access and my phone went from S-off to s-on...
Oh yeah and I already tried to clean my usb-port..
Some extra Infos: when I boot in my recovery menu:
**** TAMPERED *****
**** UNLOCKED *****
M7_UL PVT SHIP S-ON RH
HBOOT-1.57.0000
(and in fastboot-mode): FASTBOOT AC
seven09 said:
Hello,
I am pretty sure that I bricked my usb port and there is NO way to solve my problem but just to be sure:
Does anyboidy know if I have a software or a Hardware issue??
No computer recognized my phone. Im 100% sure that it is no driver problem, My computer just say: Unknown device. code:43
My phone was unlocked and rooted, so I tried to flash a stock rom with root-access on my HTC. I thought it could solve my USB-problem, but it did not, Unfortunately I lost my root-access and my phone went from S-off to s-on...
Oh yeah and I already tried to clean my usb-port..
Some extra Infos: when I boot in my recovery menu:
**** TAMPERED *****
**** UNLOCKED *****
M7_UL PVT SHIP S-ON RH
HBOOT-1.57.0000
(and in fastboot-mode): FASTBOOT AC
Click to expand...
Click to collapse
Assuming you have tried multiple ports, cables and computers with the same results. You could try an OTG cable, it may fail but if not you could at least move a rom to the phone.
** Put a zip file on USB
** Attach USB to phone reboot to TWRP
** TWRP >> Mount usb-otg >> Install using file from USB
Sorry about S-OFF, it would have made your life easier to remove the tampered & unlocked to return the phone for repair. My guess it is hardware.
majmoz said:
Assuming you have tried multiple ports, cables and computers with the same results. You could try an OTG cable, it may fail but if not you could at least move a rom to the phone.
** Put a zip file on USB
** Attach USB to phone reboot to TWRP
** TWRP >> Mount usb-otg >> Install using file from USB
Sorry about S-OFF, it would have made your life easier to remove the tampered & unlocked to return the phone for repair. My guess it is hardware.
Click to expand...
Click to collapse
Thanks for your reply.
I tried an OTG cable already and it failed Well I could copy a rom on my phone. E.g. using dropbox but without twrp or another recovery its pretty useless ..
thanks anyway
hi guys, i think made a big mistake. i erased my custom recovery. i have a all in one kit hasoon 2000 3.1 version. but i forgot how to use.
or if you give any advice or tutorial i can make this.
because i cant use my phone
PLEASE HELP!
adilsefa said:
hi guys, i think made a big mistake. i erased my custom recovery. i have a all in one kit hasoon 2000 3.1 version. but i forgot how to use.
or if you give any advice or tutorial i can make this.
because i cant use my phone
PLEASE HELP!
Click to expand...
Click to collapse
Download the android SDK or "minimal adb and fastboot"
Download TWRP 2.8.5.0, save it in the same folder where you have adb and fastboot
boot your phone in bootloader mode/fastboot usb
open a terminal window from your adb/fastboot folder
Code:
fastboot flash recovery name_of_recovery.img
fastboot erase cache
fastboot reboot-bootloader
Done
when i enter to bootloader it will see ''fastboot ac'' not ''fastboot usb''
device not enter to usb mode but still working.
there is no any hardware problem. because i cant see ''usb not recognized''
i dont know how i erased fastboot usb mode.
i think i convert to fastboot ac to fastboot usb mode. if i make, it can works
but how?
***TAMPERED***
***UNLOCKED***
M7_U PVT SHIP S-ON RH
HBOOT-1.54.0000
RADIO-4A .17. 3250. 14
Open DSP-v31.120.274.0617
OS-2.24. 401.2
eMMC-boot 2048MB
JUN 23 2103,05:18:07.0
adilsefa said:
when i enter to bootloader it will see ''fastboot ac'' not ''fastboot usb''
device not enter to usb mode but still working.
there is no any hardware problem. because i cant see ''usb not recognized''
i dont know how i erased fastboot usb mode.
i think i convert to fastboot ac to fastboot usb mode. if i make, it can works
but how?
***TAMPERED***
***UNLOCKED***
M7_U PVT SHIP S-ON RH
HBOOT-1.54.0000
RADIO-4A .17. 3250. 14
Open DSP-v31.120.274.0617
OS-2.24. 401.2
eMMC-boot 2048MB
JUN 23 2103,05:18:07.0
Click to expand...
Click to collapse
If your phone is booted in bootloader mode and displaying "fastboot AC" instead of "fastboot USB" its simply because its detecting power on pins 1 and 5 but doesn't detect any data connection via pins 2 and 3. It might be because a defective usb port on your computer or on your phone, because of a defective usb cable or because you are simply using a usb power cable instead of a usb data cable. Usb power cable only have 2 contacts for pin 1 and 5 (power+ and power-). Usb data cable also have pin 2 and 3 (Data+ and Data-).
yes i plug the original cable now is iam seeing fastboot usb but i installed also htc sync i see usb not recognised. what will i do?
i'm having a similar problem actually.. for the LIFE of me i can't get fastboot to recognize my device. i have htc sync drivers. have full access to ADB, but for some reason no fastboot. i've tried on windows 8.1, but also recently have been trying on Ubuntu.. so drivers shouldn't be an issue. I'm currently s-on, not rooted, and have no recovery. i flashed an RUU trying to return my phone to stock for sale however the sale fell through now i'm trying to get cm12 back on it. i've been trying to flash the recovery through Hboot.. but from everything i see it seems like you need s-off for that to work. without fastboot i can't achieve s-off although all i really want is root.
ok i understand. but whats meaning ''RUU''
or how can install cyanogenmod12 ?
i need use my phone.
adilsefa said:
yes i plug the original cable now is iam seeing fastboot usb but i installed also htc sync i see usb not recognised. what will i do?
Click to expand...
Click to collapse
uninstall HTC sync but keep the drivers installed. Also make sure you latest drivers version.
plug your phone to your computer, boot it in bootloader/fastboot usb mode. Go to windows devices manager, take a screenshot of your device manager and post it here.
View attachment 3208438
alray said:
uninstall HTC sync but keep the drivers installed. Also make sure you latest drivers version.
plug your phone to your computer, boot it in bootloader/fastboot usb mode. Go to windows devices manager, take a screenshot of your device manager and post it here.
Click to expand...
Click to collapse
i uploaded here is the below
@alray
adilsefa said:
View attachment 3208438
i uploaded here is the below
@alray
Click to expand...
Click to collapse
your drivers are not installed. install htc drivers: http://www.mediafire.com/download/msfud4uem3gew2d/HTC-Mobile-Driver_v4.14.0.001.exe
View attachment 3208690
now i see this device issue.
@alray
hey bro are you there?
what will i do
@alray
adilsefa said:
hey bro are you there?
what will i do
@alray
Click to expand...
Click to collapse
Try to install the drivers manually. Check nnk71's guide linked in my signature. In post 2 of his guide are FAQs. HE explain how to install drivers manually. Follow his instruction at 2) and everything should be fine. Sorry can't help more now I'm at work.