Related
Well, I got a bit cocky after previously flashing a T-Mo Tab and didn't carefully (re) read the directions (I know...dumb..dumb...dumb).
Anyhoo, I rooted a factory AT&T Tab that was running Froyo, I verified the bootloader was not locked with the downloaded .apk..and began flashing BG stock (en route to Overcome) with only the PDA and Phone files selected....no .pit and not repartition checked.
The load went to about 90% then Odin "stopped unexpectedly". The device is currently stuck on the download screen showing the stuck progress bar. I am keeping it like this to drain the battery.
I have to confess that I actually did this same thing once before (on a unit that was returnable). I have only NOW determined that it is almost certainly the lack of the .pit that is causing this. I know from this previous experience that if I force the unit to power down...it will do nothing..no restore...no download. Therefore, I am keeping it in this state to drain the battery quicker.
I found another poster on the forum that has the ability to "un brick", but I am hoping that after the battery drains I can get to the download screen and Odin again.
Anyone have any thoughts? Am I likely to recover after the battery drains? Time will tell I guess...but I am anxious!
Thanks much...
p
Sorry...obviously I was flashing GB (GingerBread) stock.
TIA...p
If its in download mode doesn't ODIN recognise it? If so, just reflash with all the necessary files...
If you drain battery you might not get it working again. There have been people with problems like this....
Odin "sees" it as evidenced by yellow in COM port...but upon attempt to flash it fails to connect - load never starts.
Thanks for your reply anyway.
1st post, w00t!
Mine did something similar. After multiple attempts at getting Odin to connect, it finally did. I basically had to put it into download mode 5ish times. Pressed the 'reset' button in Odin a few times, unhooked it from the USB cable a few times.
I wish I could be more specific, but I don't remember the exact process, sorry . What I can tell you is that I was able to charge it over night by just leaving it plugged in and from what I could tell, it was powered off.
Best of luck mang!
Thanks for the note.
I wish I COULD put the device back into download mode.
Completed dead now....
Looking at un-bricking options (Samsung, private party, etc..)
PM sent...
Hey there, i am feeling somewhat overwhelmed with all of the advice going on out there and need someone who can give me the answer to my specific problem hardware wise without breaking a sweat...
I flashed a froyo 2.2 rom onto my phone a while ago, recently all of my apps stopped working, and i could no longer install any apps.
Couple days ago i tried openning gmail and the screen went black and gave me the bzzzzzz...............................bzzz...bzzz...
vibrating error that you usually get when an app crashes.
Now the phone continues doing that even when booted up and stuff
It starts right after the S screen and repeats until the battery is removed.
My phone can't get into download or reset mode using the 3 button method so i bought a jig off of ebay, works like a charm.
however NOW, i cannot get the computer to see the phone; both when it is on and attached and in download mode and attached. Odin can't see it, neither can Kies.
If i can get either to see it, i can look up the flashing process to make sure everything is right.... but as of yet nothing i am doing is making a difference.
Thanks for any help
Ok, I'd focus on odin so disable Kies (in task manager processes - all the kies processes).
Then I would 1) reinstall the drivers (standalone ones) 2) Have a few versions of odin to try (like 1.3, 1.7 and ez odin) 3) Clean your usb port on the phone (and computer maybe too - whats the harm?).
Usually if you are sure the drivers are Ok then you should be able to odin working with a nice clean port. They are more sensitive to dirt/moisture or whatever than they should be.
Try that and let us know...
BTW Some people think that the order is important but I've never noticed that. I always have odin open and then connect it but cant hurt to try the other way around too.
Hey thanks alot,
I am at work right now but i am optimistic about trying that out lol.
Just so i know for when the time comes and if Odin works, what files do i need to flash it? .pit, .tar and anything else specific for Bell Canada?
I only ask because you are with Bell so it is probably a very simple answer for you. Otherwise I am sure i can find it elsewhere.
Thanks,
I'll keep you updated
Josh
Download the complete jl2 rom from link I posted yesterday (search my posts) with repartition ticked, then flash the kc1 rom from stock rom link on xda or at samfirmware.com and flash without repartition if you want the latest. You could just try the kc1 step but I you need to repartition.
Sent from my GT-I9000M using XDA Premium App
Hey man,
my phone has never been sent in for repairs or replaced...
I was reading one of your other posts and you advised another member to send it in and maybe they will replace/update hardware?
I have still had my phone for less than a year so sending it in will be no problem at all...
Should i flash to the latest myself or return to stock and send it in?
I really appreciate your help.
Thanks
Well he knows his is broken as he can see that his internal memory reads 0 (which means its cooked - ask me how I know...) and he was trying to fix it in a round about way. Or there was the guy who flashed a captivate rom - that was just a big no-no.
You might just have a corrupt partition or some other corruption in the file system. I seem to get that all the time and its a pain but very fixable .
Alright, sooo
-uninstall Kies
-install drivers only
-try to connect to Odin
-If succesful flash with Odin
-dance with joy
Got it, I will update you later when i get home.
Thanks
installed drivers on my work computer (32 bit windows xp) and nothing... I've tried phone off, phone on, phone in d/l mode... It doesn't pick up anything...
I can try it on my Windows 7 comp at home and see if that works but i'm wondering what the worst case scenario is just bringing into Bell and having them fix it... Am i looking at charges, warranty voiding, etc.. etc... to have it fixed or could i BS my way out of it?
Fuuuuuuuuuuuuuuuuuu
pretty sure i flashed the wrong firmware on my phone, when it boots up it says GT-I9000 not GT-I9000M.
It worked fine for like 6 months so i never questioned it... damn damn damn
Not to be completely devious but i got an extended warranty that replaces the phone due to water damage, theft, etc. etc...
If there is no other way should i take advantage of that?
I would hate to jump to one of those actions but i am somewhat panicking becuase i made a super-noob mistake and effed up my phone....
I9000 firmware is completely compatible. The text you see is from the kernel which are always for i9000 unless you have one of the three bell firmwares. So that's not the issue.
Sent from my GT-I9000M using XDA Premium App
RogueCow27 said:
Not to be completely devious but i got an extended warranty that replaces the phone due to water damage, theft, etc. etc...
If there is no other way should i take advantage of that?
I would hate to jump to one of those actions but i am somewhat panicking becuase i made a super-noob mistake and effed up my phone....
Click to expand...
Click to collapse
I would keep trying. I have gotten warranty before and I was in the same predicament as you almost except I knew that the internal memory was dead. But that was also around the time when most of the I9000M models were dying. They might be checking more now.
If you get odin to flash a stock rom then you can go for it but by then you should be able to fix it.
Sent from my GT-I9000M using XDA Premium App
Alright i will keep trying.
As far as the firmware goes, my gf and i both have the same phone, but she kept heres official and i put custom roms on mine (just the 2.2 because it wasn't available)
We are both on bell canada so i asked her to boot up her phone and the beginning message on hers says GT-I9000M so it freaked me out lol
I will try on my home computer,
keep your fingers crossed for me
Alright, so Odin can now see my phone (it was the damn cord, my Win 7 comp couldnt see it but my xp work laptop can)
Which firmware would you recomend flashing? Stock gingerbread or a slight variation?
I am at work right now so i can wait a bit for a good response. It'd really help me out if you could provide links and tips to the best firmware out right now (i have no problem flashing a custom ROM if it is good).
Thanks alot,
Josh
Succesfully Flashes Gingerbread 2.3.4
Thanks for all your help!!!
how did you manage to see it in odin?
i have te same problem with restarting just after first screen (after flashing to gingerbread) but i cant see it in odin so i cant flash it again?
when i connect it when turned off, a small icon appears with usb connected sound but its still not visible.
Is it maybe my win7?
help, anyone please
Did you start in Download mod? Did you kill the Kies processes in you Win7 task manager ?
If yes, sometimes Windows takes time to install the drivers (be sure ton be connected to the internet), you should also close and relaunch Odin.
i launched download mode with sdk, and now i cant start it.
i went to another pc with xp. it installs drivers but odin cant recognize it.
Well i did it on my work XP computer becuase WIN 7 wasn't recognizing it. But it turns out the whole time the cable i was using would connect to charge, but not act as a pc connection.
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
I have the same issue. I was tryint to load Cognition and it just gets stuck on the ATT screen but I haven't tried a jig yet. I was wondering if I can replace the files on the phone with good files that aren't corrupted and see if it boots up because droid explorere can still pick up the phone and so does Odin but when I do a master reset nothing happens.
@rajasekhar - Have you tried: Removing all parts (battery, sim, sd) let it sit for a few min (my preference is around 10 min to insure no residual power is left in the system) then hold the jig in place and putting the battery back in? Keeping the jig in place, so that as soon as the device gets power it is immediately seeing the jig, before it can try any other processes.
A bit difficult to do with hand made jigs I know. If you still getting nothing then your in for the worst and the phone need a JTAG or service center visit.
Tho it sounds a little odd that it could boot up to seeing the AT&T logo, but does not respond to the jig. Might even be a hardware problem.
@i3oots - Since you say your still getting PC response your safe to try and reflash it or just pick something different altogether. Tho you might wanna let ODIN settle and just sit there doing nothing for a few min, w/o then w/ the phone plugged in. Or learn about Heimdall and go that route.
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
You have probably Hard Bricked your phone. A JIG will not work to recover the phone. If the phone has any life at all, then the JIG will work. Else, u hard bricked it...you should never remove the usb cable when flashing bootloaders or odin or anything!
the only solution is to get a JTAG which can recover hard bricks OR you can go to a warranty store (don't know about india) and make up a sob story and have them replace it..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
Does your computer recognize the phone? If odin is open, does the box turn yellow when you connect your phone? Make sure you have the right drivers. I think cm7 and captivate drivers are different. Keep trying with the jig. Just because you can't see anything on the screen doesn't mean the phone is dead.
i3oots said:
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
Click to expand...
Click to collapse
If your phone is booting up far enough to send out USB info for ODIN and other PC programs to see it, then your still in a workable condition. This also means you can still get into download mode, but since things arn't working properly it will be harder. Depending on which bootloaders your phone has will direct which methods you'll have to try out to get into download mode.
AFTER you've had a chance to look around the forum and self-educate on the different ways of getting into download mode. If your still having problems give us a lil more info of what you were running before the flash and to which version of Cog you were trying to flash.
Did anything worked for you, if not only a jtag can help you looks like u hard bricked the phone.
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
bricked maybe not
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU...... ................................................. I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cant find the original post
rajasekhar19489 said:
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
Click to expand...
Click to collapse
rajasekhar19489 said:
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Click to expand...
Click to collapse
If you just wanna know a bit about the process ask this guy. He is pretty much the only person in the US (I know not all to useful to a person in India) that does JTAG for the cappy.
I can tell you this much, it requires a special device called a Riff box and it sends boot info directly to the chip on the main/mother board that is used for the booting process.
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
malebornin69 said:
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU......
Click to expand...
Click to collapse
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
DaNaRkI said:
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
Click to expand...
Click to collapse
Thanx DaNaRkI .. hmm well i would now again start digging the threads for seeing wat u have suggested ..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
hello brother,,
u can find the Jig here in india... i also purchased... and it worked for me..
Download-Mode-USB-Jig
press thanx if it helps..
rajasekhar19489 said:
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
Click to expand...
Click to collapse
Hope it helps I wish I could find the original post again to thank the guy that told me how to do it. I had sent that phone back to att and the promptly sent it back and told me the water dammage sticker in the bat compartment was missing and they wanted to charge me 409 bucks for the phone ....long story short it was there when I sent it and I told them to go pound sand up their ass because I wasnt paying them that much and ended up paying 125 bucks for a paper weight.So that is when I decided to have it jtaged but figured I would give it one more shot before mailing it off. That was when I found the post from that person and low and behold it worked........................... I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cat find the original post
malebornin69 said:
Hope it helps
Click to expand...
Click to collapse
Buddy tried it ... Thanx for that..But dint help . Now going for another options i mean in search for other options
But ppl help me with JTAG thing and its users(or developers) availability in india
Forgot to mention
I Missed to explain my flashing procedure i have done this time . Like I never tried flash a boot file along and so was reading some threads about boot loader variations between FROYO and GINGERBREAD so i tried flashing ablong with boot loader and then I got the stock gingerbread file i put the boot loader SBL in heimdall Firstboot loader path .And Boom the first reboot got stuck and i removed the battery and then again when i tried to restart the phone is dead
Thinking this might have where the whole thing went wrong and made the cell dead .
I superonelick rooted. Then i downloaded ROM Manager and flashed CWM. Then i returned to stock using ODIN 1 click. It failed.
Now when i turn phone on it just shows a white screen and nothing else happens... i can't find problem anywhere else on google. I've rooted many captivates but never had this problem! UH-OH... Help please
the same thing happens whenever i try to boot into recovery and into download mode...
You are gonna need a JIG. Check mobiletechvideos.com to get one or u could make one urself.--see this for homemade jig... [HOWTO] *Layman's iGo Jig* [Solderless]
Which One Click Odin did u use ??
i used I897UCKH3_withBL
i used it the night before and did the exact same procedure with no fault... i didn't do anything differently...
If u can't get into download mode by pulling battery/ replacing battery and connecting the micro usb to the phone, having already connected the usb end to the computer... then u r gonna need a jig.
And a friendly fyi, once u flash Gingerbread firmware that contains the Bootloaders, there is no need to flash a firmware that contains GB Bootloaders again if u are flashing another or the same Gingerbread firmware... or even going back to Froyo or Eclair for that matter, because the GB Bootloaders are backwards compatible.
i pull the battery. press both volume buttons, plug in usb chord to phone (already plugged into computer) then put in battery. The phone screen turns on (all white, blank screen)
I've seriously done this with 5 captivates... i've never had ANY issue... and now this happens. I'm so confused.
Do u remember or can u still see on the Odin where it failed ?
Either way though, u r gonna need a jig.
But on the plus side, it is not hard bricked.
Yeah i just did it out of order... ugh...
well this sucks, cuz it's someone elses phone and it's 9pm on a sunday night... I don't know what to tell him, lol.
Once u get or make a jig, then just flash the KH3 that contains NO Bootloaders 1st, that is, if that is still the base u want to take the phone to. This should get the phone working, if the Odin failed after it had already installed the GB Bootloaders.
good grief... i still can't believe this has happened... I guess i'll just give him my phone to use... i'm never helping anyone else again with their phone. I don't want to be responsible for this crap.
Can i just take his phone to AT&T store and get a new one (it is only 2 months old)
i mean are there any other ways to try and get the phone to do SOMETHING? I mean it turns on....
Jig is ur answer.
If it turns on still its fixable if you tried download mode and the screen is all white does odin still see the phone??
Sent from my I897 using XDA App
odin does not see the phone.
As others have mentioned jig is your only option at this point, but easily fixed none the less
Sent from my I897 using XDA App
okay well i just bought one. I'm really short on time to make one this week. So it'll be here tomorrow or wednesday.
what are the actual instructions once the jig comes in? I just plug it in and it goes into download mode? Then hook it up to computer and ODIN. (which odin do you recommend for cognition, or do you recommend another OS? )
Search, man, search.there are dozens of threads that answer this, and all the questions you've had.
You may also want to try one of the heimdall one-clicks, especially if ODIN isn't working for you.
i appreciate that. I just wanted the opinions of forum members that i respect. (i know there are a lot out there who are worthy of it as well.) So i figured while i had one's attention, i would ask
There is nothing wrong with asking questions, but you can learn more by searching for one answer than asking 10 questions.
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
hav0c said:
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
Click to expand...
Click to collapse
WOW...
the problem is that i live in a fu**ed up country and we dont have samsung here.
all phones come without warranty and by smuggling from other countries
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Dude, if you have no way of repairing a bricked phone in your country then stay away from flashing custom ROMs!!!
Sent from my superior GT-N7000 using Tapatalk
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
Click to expand...
Click to collapse
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
Click to expand...
Click to collapse
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
octavian90 said:
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
if you had gone through what i went through to get the phone, you would probably do the same.Thanks for the reply, any thing would help me right now.
vijai2011 said:
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
Click to expand...
Click to collapse
Thanks man, i will definitely try it right away.
mother board
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
chasmodo said:
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
MR.change said:
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
Click to expand...
Click to collapse
pvillasuso said:
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
Click to expand...
Click to collapse
You guys are awesome, im gonna do everything you said and get back with the results, fingers crossed.
I have a friend who's going to Dubai,UAE in a week or so. if nothing worked i'll send the phone with her to repair it at samsung,does anybody know if there's a samsung service center in Dubai and give me the location ?
i cant thank you enough,really appreciate all the help.
firasusman said:
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
Click to expand...
Click to collapse
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Try a different USB cable?
Sent from my SPH-D710 using XDA
izzmohamed said:
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Click to expand...
Click to collapse
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
jeffrey567 said:
Try a different USB cable?
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
I did, still the same.
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Hmmm,i'll try cleaning it.I had the same situation, so the jig should work fine despite this problem ?
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
lanwarrior said:
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
Click to expand...
Click to collapse
I am wondering the same thing, mine got bricked about a week ago and I don't really know what to do with it