Database Develop

Help me please...galaxy tab Exclamation mark

i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....

water30 said:
i want to flash new firmware but i have little problem...now my tab is show exclamation point between a phone and a computer.
but Galaxy tab can not remove battery for reset this error...
Help me please....
Click to expand...
Click to collapse
what did you do to get to this screen? Is this after or before you upgraded firmware?

GANJDROID said:
what did you do to get to this screen? Is this after or before you upgraded firmware?
Click to expand...
Click to collapse
after upgrade firmware odin show reset but the my tab not reset then i just manual reset (i can take this method for my galaxys ) after that.....

Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again

i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?

primeroz said:
i have the same problem, phone - exclamation point - computer ... but i can't get into recovery mode to do a wipe .
is i press VOLUME UP or DOWN + POWER i always end up with the same exclamation point screen ... any help?
Click to expand...
Click to collapse
Read my above post. Go into download mode (volume down + home + power) you'll still have the same image but the phone WILL be in download mode. Then flash your previous firmware and you're sorted.
Sent from my GT-P1000

You probably got that by messing with the kernel. Fund the zImage from the firmware, extract it with a .tar extractor then use something like heimdall to flash the kernel and it should work.
Sent from my GT-P1000 using Tapatalk

Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.

Help please
slaia said:
Hi. I'm looking for solution for my problem but nothing has helped me. I cannot restart mu GTab or put it in download mode. I always land into Android system recovery <3e>.
My problem: I cannot restart my GTab anymore. It started when I wanted to do a backup with ROM Manager. Unfortunately EURO TAB isn't supported yet. Then I want to find out whether nandroid backup is possible. From ROM manager I booted into recovery. But there isn't nandroid backup. And now I cannot boot GTab anymore. Every time I restart it brings me back to Android system recovery <3e>. I would be grateful for every solution.
Click to expand...
Click to collapse
Having the same problem too... anyone can help?

If you see Phone-!-Pc on the Tab screen it is the download mode.
You can reflash it using Odin, however, you will need to do full Rom flash. I had similar problem and solved it by replashing.
I followed the latest guide published in this forum and Roto-JME rom with reformatting of internal sd.

Phone ! PC error FML!!!
GANJDROID said:
Edit:
Had the exact same thing happen to me, but its just a bad flash.
Download the JM6 zip (in the development forum) and flash it via Odin. after the device has rebooted, if the previous apps havent been deleted, go into recovery and perform a factory reset and reboot again
Click to expand...
Click to collapse
Where can i download the JM6 zip??

Hey guys,
I tried to manually update my tab to Gingerbread today via Odin, but it kept hanging on select partition (I discovered I used the wrong PIT for the firmware I was going to flash, but as I didn't select the firmware yet that shouldn't be a problem). At last I decided to quit Odin (which might have been stupid...) and try it again. Then it kept haning even earlier, so I tried to restart the device in download mode. However, whatever I try it keeps giving the Phone ! PC sign. If I try to just boot, if I try to go into recovery mode or if I try to go into download mode. I saw a lot of possible ways to solve the problem, but my PC doesn't recognize the tab anymore. If I connect it, it does give the "usb device connected" sound, but there is a popup which sais "USB Device not recognized. One of the USB Devices attached to this computer has malfunctioned and Windows does not recognize it. For assistance in solving this problem, click this message". I already tried to reinstall the driver but it doesn't work. Also Odin and Heimdall don't detect any device.
Does anyone know a solution for this problem? Maybe taking the battery out? (for which I have to buy a new triangle screwdriver, so I need to know if it could possibly work first. It takes some weeks to order such a thing I think...)
EDIT: I played around a bit with the drivers again, and suddenly both Heimdall and Odin recognized it. However Odin stopped recognizing it again. Then I pressed "read PIT" in Heimdall, which worked. After that the device started booting up to the Samsung logo animation and then powered off again. Now it doesn't do anything anymore, not even showing the Phone ! PC screen. I'll charge it overnight (maybe it's gone empty during the process), so I hope that helps.....

In some strange way, the phone works again..... So never mind my post above.

[Q] Need the rigth USB driver

Hi all,
Have a kind of brick at the moment.
Whats working:
Download mode
Recovery e3
The device is booting up, but I did the wrong battery mod for this firmware so it just vibrats and turns on and of.
The PC doesn`t recognize the device, it just sometimes shows up an unkowm device.
I have found this tread http://forum.xda-developers.com/showthread.php?t=777872 and now I have some hope!
I have tried to pick the Kies Driver (16 Shrewsbury) and all the others from Kies and also the google drivers from the SDK. But none from the works.
Someone can point me to the rigth driver, plase
Fortunately I still have my G1
Sorry for my English.

If you have a black screen after booting then try resetting back to factory settings in recovery mode.

Thank you,
I wiped al i could in recovery e3.
The device is booting up, sound is coming, I see even the SGS logo, after No package was found that provides the FACTORY TESTKEYS
I guess it´s becaus I aplyed the wrong battery Mod for my firmware

If your phone can go in download mode try to reflash a rom with odin

I allways extract the latest kies install file to hdd and pick the latest drivers setup package out of it. I NEVER installed kies just to get some drivers
Sent from my GT-I9000 using XDA App

[Q] my device is not booting. help

Hi guys,
i have my I9000 upgraded to froyo and rooted without any problem. it had vodoo lagfix also with no problem
today, i installed (( galaxy s tweaker )) app and i dont remember waht i did but the device then shut down and reboot but it stuck to the boot screen that contains galaxy and samsung logo and it keeps restarting the same screen many times and nothing further happens.
i tried the recovery mood ( factory reset, restore, format ) but nothing works.
i tried to connect it to my pc and reinstall the rom from odin but odin is not recognizing my device even in downloading mode and i got this notification from windows that usb device was not recognized ..
please please please, help me
thank you in advance

life art said:
Hi guys,
i have my I9000 upgraded to froyo and rooted without any problem. it had vodoo lagfix also with no problem
today, i installed (( galaxy s tweaker )) app and i dont remember waht i did but the device then shut down and reboot but it stuck to the boot screen that contains galaxy and samsung logo and it keeps restarting the same screen many times and nothing further happens.
i tried the recovery mood ( factory reset, restore, format ) but nothing works.
i tried to connect it to my pc and reinstall the rom from odin but odin is not recognizing my device even in downloading mode and i got this notification from windows that usb device was not recognized ..
please please please, help me
thank you in advance
Click to expand...
Click to collapse
Im guessing kies does'nt kies reconize phone? maybe uninstall then reinstall kies which will reinstall drivers. Have you tried pulling out the battery for 10mins and then retrying?

hi tragusman
unfortunately, both kies and odin dont recognize my phone though i tried to reinstall kies .
i tried to remove the battery for hours but it didn't work also

life art said:
hi tragusman
unfortunately, both kies and odin dont recognize my phone though i tried to reinstall kies .
i tried to remove the battery for hours but it didn't work also
Click to expand...
Click to collapse
If you can get into download mode then Heimdall will be able to detect your phone using either Windows or Linux. Heimdall works on OS X also however a fixed bootloader is required.

update:
i installed the driver on my pc from softpedia
i restarted my pc and odin can recognize my phone now
i flashed froyo rom and its not working . i will try another rom and see what will happen
i installed 2.1 rom followed by 2.2 rom and its working like a charm
problem solved
thanx

[i9000b] BSOD - Phone ! Computer Screen

I had Android 4.0.3 (IceCream Sandwich) on my Galaxy S GT-I9000B (I did install it through Odin, nothing went wrong), but is was laggish (too much for it to handle, I think) and after a few months, I decided to roll it back to 2.3.3 (Gingerbread).
I started the process to install the firmware through Odin3 v1.85 - the file I download (from sammobile.com/firmware, had only one file that I used on the PDA space.
Odin recognized my phone and I started to install it, but after a while my phone was stuck on the downloading screen (2 hours of installation, I tought that something went wrong).
I then turned my phone off to try and install again, but when I turned it on, there were a Phone - exclamation mark - Computer Symbol.
I can get it to dowlonad mode (Volume Down+Home+Power), but when I plug it to the pc, it says "unknown device" and it can't find drivers for it.
I think I have the latest drivers from Samsung (I had from Kies and I re-downloaded a file somewhere from this forum named SAMSUNG_USB_Driver_for_Mobile_Phones_1_5_6_0.exe).
It appears that since windows can't install the drivers, Odin doesn't recognize the device - it was recognizing it before, when I was installing the firmware.
Now I'm stuck - I tried anything I saw in this forum and in other places - I did even pray for a miracle, but it didn't work
I know that there must be a way, but I don't know how.
Before I forget, I'm using Windows 7 Ultimate x64.

If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.

KainFromNod said:
I know that there must be a way, but I don't know how. Before I forget, I'm using Windows 7 Ultimate x64.
Click to expand...
Click to collapse
Ok, k4Z3666, has given you a starting point...the phone is still in download mode but without a booting ROM, so its OK, the problem is your PC, USB cable or USB port. If you want to be quick about it, just try on a lap top..if not a simple Reboot of PC ( after removing power cord) and Phone (after a battery Pull), and a switch to a different USB port at the back of PC can solve this for some...for other solutions try these http://forum.xda-developers.com/showpost.php?p=27205737&postcount=4571 anything else you may need can be found on My Android collections., link below

k4Z3666 said:
If you can get it in download mode everything should be fine, I've had a problem like this, my pc couldn't see the phone in download no matter what. Try to use another USB port, better another PC. Also I've heard that x64 doesn't get along well with Odin. If possible you can try Linux and Heimdall, after all Android is Linux too.
Click to expand...
Click to collapse
I tried other USB Ports and also rebooting. It was working just fine - it seems like a driver problem to me.
My notebook is dead, but I'll try using someone else computer.
Does Odin runs in Windows XP? I might try it in my virtual box - I doubt that it will work, but it is the best thing I have to do untill tomorrow.

I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?

KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300

KainFromNod said:
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]

KainFromNod said:
I got it working in my mother's notebook - should I try something different? I only have the PDA, should I try a PIT?
I don't know what those do, but I read somewhere that PIT is used to recover bricked phones.
EDIT: I installed only the PDA, it worked fine on the 2nd time (first time, it got stuck but I could make it work changing the usb port and cable).
Now it is on loop - it repeats the samsung logo over and over again. Any ideas now?
Click to expand...
Click to collapse
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah

Ok, I'm posting it here just to leave a reply and reference for future generations, as my problem was solved.
xsenman said:
what ROM did you use? Did you do any wipes?
Opps..you got an i900B, so make sure you are only using I9000B ROMS as i9000 is not compatible with your phone
I used a firmware from my country (available here: sammobile.com/firmware/?page=3&model=GT-I9000B&pcode=ZTO&os=1&type=1#firmware) and I wiped the cache (I'm not sure what this means, but I believe it is the 2 options on volume up+menu+power)
Follow guidelines from here
http://forum.xda-developers.com/showthread.php?t=919219
http://forum.xda-developers.com/showpost.php?p=22941192&postcount=300
Click to expand...
Click to collapse
k4Z3666 said:
Assuming that you're on the right rom for your phone can you enter recovery mode? Try reinserting battery, and enter recovery with [vol+, menu button, power on]
Click to expand...
Click to collapse
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
yahyoh said:
Yep if u want to back to stock u need pit file because ICS use different system file
Why u don't like ICS ? Its way better and faster than sammy ROM even its more stable , I think u should try it again with devil kernel with oc to 1.2 it will fly u can add some live oc which will give more fluidity
Sent from another galaxy powered by CM10 & Syiah
Click to expand...
Click to collapse
ICS wasn't faster here - it was laggish and always crashed some common apps (gallery, music player). I believe that the firmware wasn't completely "done" as it was being adapted from another version (my phone is brazilian) and some functionalities that it has (i.e. digital TV) wasn't available.
What I done to correct the boot was simple (I found a tutorial in a brazilian site, so it had all the roms that I needed).
1) Used a PIT and a stock rom to get it back to factory version;
2) Upgraded to Froyo (original) - That was kind of a mistake, the tutorial said to do it because then KIES would update it automatically to Gingerbread. The phone was fully functional, but KIES said that it couldn't update it (it recognized the phone and everything).
The tutorial stoped there, but since I had the ROM, I used Odin to install Gingerbread (the one that was looping) and it was done.
Now I need to remember how to root it because there are some dumb apps who can't get away (i.e. Orkut app, some demo games).
Thank you all for the help!

KainFromNod said:
I was entering recovery mode, but it was giving me some error when I tried to wipe the 2 things that I forgot the name =/
Click to expand...
Click to collapse
From recovery you can always try to flash another kernel, that would probably resolve things too. Anyways the problem's solved, glad to help

[Q] CM10 Stuck at bootloop, can't enter recovery, and computer doesn't detect

So I've seen a lot of threads on here with this kind of problem but none of the solutions work for me.
I just flashed CyanogenMod 10 nightly, was tinkering around on it, rebooted and I was just stuck in a bootloop. I can't get into recovery but I can get into download mode. However, my computer just doesn't detect the phone at all. I can't get Odin to detect it to flash a new bootloader or anything. I've tried installing Nexus drivers and everything. It just doesn't even detect that anything has been plugged into the computer. But the usb powers on the phone. If I plug into power I just get a spinny loading wheel that doesn't move and refreshed every few seconds.
I'm stuck. I can't get into recovery to flash, and I can't get my computer to detect it to flash. Help me please?
EDIT:
Okay so tried 3 different USB cables and I've found one that works. I tried flashing a new bootloader but I used the bootloader bit on Odin instead of pda (total noob mistake) now my screen is just black and won't turn on. I can get into download mode to flash stuff again. But what do I need to put in the bootloader section to get it back to normal?

I think you have to start from Gingerbread again
Search on samifirmware a 3 files firmware of Android 2.3.6
After that search on google a Step by Step guide how to flash a Rom with Odin.
I think after that i should work.

ChrissehB said:
So I've seen a lot of threads on here with this kind of problem but none of the solutions work for me.
I just flashed CyanogenMod 10 nightly, was tinkering around on it, rebooted and I was just stuck in a bootloop. I can't get into recovery but I can get into download mode. However, my computer just doesn't detect the phone at all. I can't get Odin to detect it to flash a new bootloader or anything. I've tried installing Nexus drivers and everything. It just doesn't even detect that anything has been plugged into the computer. But the usb powers on the phone. If I plug into power I just get a spinny loading wheel that doesn't move and refreshed every few seconds.
I'm stuck. I can't get into recovery to flash, and I can't get my computer to detect it to flash. Help me please?
EDIT:
Okay so tried 3 different USB cables and I've found one that works. I tried flashing a new bootloader but I used the bootloader bit on Odin instead of pda (total noob mistake) now my screen is just black and won't turn on. I can get into download mode to flash stuff again. But what do I need to put in the bootloader section to get it back to normal?
Click to expand...
Click to collapse
Nothing. Never put anything in the bootloader section. Instead, look for a rom that has bootloader in it. I believe that the darky resurrection rom has bootloader.
Sent from my Nexus 7 using Tapatalk 2

I had the same issue with cm-10-20121125-NIGHTLY-galaxysmtd (after with cm-10-20121126-NIGHTLY-galaxysmtd as well!),
symptoms: after automatic install of mentioned version the phone rebooted, but I've got stuck in bootlop, and I couldn't enter in Recovery Mode, just in Download Mode.
I've managed to fix it in the following way:
1. I've downloaded the Semaphore kernel for JB (Semaphore ver. 2.6.0), and unpacked it.
2. I've used heimdall: `heimdall flash --kernel zImage`
3. After that the phone boots and CM finishes the upgrade as usual. (I've did not lost anything from my data.)
(Environment data: OS: Ubuntu 12.04, Heimdall 1.3.2)

Boot loops with cm-10-20121125-NIGHTLY-galaxysmtd & cm-10-20121126-NIGHTLY-galaxysmtd
frantique said:
I had the same issue with cm-10-20121125-NIGHTLY-galaxysmtd (after with cm-10-20121126-NIGHTLY-galaxysmtd as well!),
symptoms: after automatic install of mentioned version the phone rebooted, but I've got stuck in bootlop, and I couldn't enter in Recovery Mode, just in Download Mode.
Click to expand...
Click to collapse
Thank you very much for the information!
I was thinking I did something wrong... :crying:
Update:
The newer versions cm-10-20121129-NIGHTLY-galaxysmtd & cm-10-20121130-NIGHTLY-galaxysmtd are OK again.
With kind regards
Joe

frantique said:
I had the same issue with cm-10-20121125-NIGHTLY-galaxysmtd (after with cm-10-20121126-NIGHTLY-galaxysmtd as well!),
symptoms: after automatic install of mentioned version the phone rebooted, but I've got stuck in bootlop, and I couldn't enter in Recovery Mode, just in Download Mode.
I've managed to fix it in the following way:
1. I've downloaded the Semaphore kernel for JB (Semaphore ver. 2.6.0), and unpacked it.
2. I've used heimdall: `heimdall flash --kernel zImage`
3. After that the phone boots and CM finishes the upgrade as usual. (I've did not lost anything from my data.)
(Environment data: OS: Ubuntu 12.04, Heimdall 1.3.2)
Click to expand...
Click to collapse
I want to buy you a beer Thanks a ton
I did this on windows 7 x64 without any problems (I had to install driver from heimdall suite)

Same here, but computer WON'T detect, normally does
Hi
I'm desperate, no phone, stuck on galaxy S boot screen, will boot into download mode but not recognised by computer
Any ideas?
Thanks