[Q] Xperia z not booting after flashing kernel ;( - Xperia Z Q&A, Help & Troubleshooting

I am extremely new to root n stuff, i successfully rooted using happy, doomlord binary and was preety happy . flashed few patchs and was happy.
Finally thought i flashing Pure X audio for xperia z and my mistake i saved DoomLord kernal on the same place. i mis selected Doomslord kernel instaed of PureXaudio ;( and finnally when i try hit reboot - it is not booting up
PLZ help !!! what do i need to do to get in to recovery tried power volume up and down , it vibrate but screen doesn't turn on or no progress ;(

Is flash or fast boot mode working properly?
Try to flash kernel again, or flash stock rom thru flashtool

doing it
Bairei said:
Is flash or fast boot mode working properly?
Try to flash kernel again, or flash stock rom thru flashtool
Click to expand...
Click to collapse
IT is not at all switching on , blank screen ;(
i tried to enter TWRP recovery , holding power on and tapping voume up - no go ;(
is there any other way to get in to revcovery ? i am preety new .. yes i am installing flashtool now and should i try tft ROM or can i flash by back up ?? i am not sure

http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium

Trying it .. small query , pl help
gm007 said:
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
Thanks a lot, i am doing it right now, downloading kernel
But my doubt is phone seem completely dead - when i hold power button it vibrates and red LED blinks, is this normal behavior ??.

no loader found for this device ;(
gm007 said:
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
Now i am stuck at teh screen where it says 'no loader found for this device flashtool' can't go any further.
My bootloader is locked, should it be unlocked to get this done
please help !!

No you don't need to unlock the boot loader to flash via flash tool'you need the drivers
http://developer.sonymobile.com/services/flash-tool/
you will need to unlock if you want to flash a custom kernel ..
Try using Sony update service sus to repair your phone
http://www.sonymobile.com/gb/tools/update-service/
Sent from my Nexus 7 using Tapatalk 2

Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
Please help If anybody has experienced
Thank you in advance

vodanhdaisu said:
Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
Please help If anybody has experienced
Thank you in advance
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2229250
Sent from my C6603 using xda premium

fish droid said:
Try using Sony update service sus to repair your phone
http://www.sonymobile.com/gb/tools/update-service/
Click to expand...
Click to collapse
You can't use SUS if you have already flashed your phone with a custom kernel, you can only use flashtool.
Just take a look to the link of gm007.

Xperia z bricked after doom Lord kernel! Help pls
QualQuek said:
You can't use SUS if you have already flashed your phone with a custom kernel, you can only use flashtool.
Just take a look to the link of gm007.
Click to expand...
Click to collapse
I am having the same problem. I have tried everything I know of including fastboot, flash mode, sus, pc companion, and so on. Still my phone won't even blink anymore. It doesn't seem to charge either. I don't know what to do. Someone please help! I was running creskole romantic and goo manager recommended the install of the doom Lord kernel v.18. Sadly, my phone never rebooted. Complete black screen.

Flash via flashtool bro.and dont use custom kernel ,use the stock kernel of doormlord one if ur locked bootloader.
Sent from my C6603

hOtsacE22 said:
Flash via flashtool bro.and dont use custom kernel ,use the stock kernel of doormlord one if ur locked bootloader.
Sent from my C6603
Click to expand...
Click to collapse
You can't flash unsigned kernels on locked bootloaders!! Just stock kernel.sin from identical FW!
Sent from my C6603 using XDA Premium 4 mobile app

PLEASE HELP i flash DooMKernel via cwm after reboot mobile not turn on push power button, the phone vibrates but does not awake
then i flash ftf via flashtool its turn on but again cant use any of the kenerl ..i have unlocked boot loader i tried to clean cash dalvik etc but always get soft bricked >PLEASE HELP
---------- Post added at 04:04 PM ---------- Previous post was at 03:06 PM ----------
Ronco87 said:
I am having the same problem. I have tried everything I know of including fastboot, flash mode, sus, pc companion, and so on. Still my phone won't even blink anymore. It doesn't seem to charge either. I don't know what to do. Someone please help! I was running creskole romantic and goo manager recommended the install of the doom Lord kernel v.18. Sadly, my phone never rebooted. Complete black screen.
Click to expand...
Click to collapse
same with me .........i try to flash it via cwm but after reboot mobile not turn on then i flash its original stock 2.67 kernel via flashtool my mobile turn on but wifi didnt works ..
then i flash
eXistenZ v4.3.5 ultra edition wifi now working but again : but cant install any of the kernels from doom kernel and others please help

my xperia Z cant turn on
Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
will it boot if i flash once again the latest firmware
Please help If anybody has experienced
Thank you in advance

raveldom said:
Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
will it boot if i flash once again the latest firmware
Please help If anybody has experienced
Thank you in advance
Click to expand...
Click to collapse
Is your bootloader unlocked? If not, you cannot run a custom kernel.
Flashing just the stock kernel for your firmware with Flashtool should fix your problem.
Sent from my C6603 using Tapatalk

kingvortex said:
Is your bootloader unlocked? If not, you cannot run a custom kernel.
Flashing just the stock kernel for your firmware with Flashtool should fix your problem.
Sent from my C6603 using Tapatalk
Click to expand...
Click to collapse
yes it is unlocked,i try to look everywhere on the internet and finally resolved d issues with d phone

problem!!
kernel not getting flashed through cwm and xperia z is rebooting again and again.what to do ?

salujapulkit said:
kernel not getting flashed through cwm and xperia z is rebooting again and again.what to do ?
Click to expand...
Click to collapse
Flash the img file from fastboot

Xperia Z not booting up after flashing
Hello guys, I badly need help in fixing my Xperia z c6603 device. I flashed the device using the ftf file from xperifirm and now my device does not boot up and stuck in blank screen.
Kindly assist.

Related

[Q] How to Rectify Bootloop Problem using Flash Tool

I was stuck up with Sony ericsson logo after installing the ROM CM7.1 , i tried to rectify this problem using flash tool but i couldn't. Please help me on this.
Vigneshj said:
I was stuck up with Sony ericsson logo after installing the ROM CM7.1 , i tried to rectify this problem using flash tool but i couldn't. Please help me on this.
Click to expand...
Click to collapse
Did you unlocked your bootloader ? And which CM rom are you using exactly ?
Vigneshj said:
I was stuck up with Sony ericsson logo after installing the ROM CM7.1 , i tried to rectify this problem using flash tool but i couldn't. Please help me on this.
Click to expand...
Click to collapse
relax dude!
maybe you can try this!
- first download X8 E15i 2.1.1.C.0.0._un.ftf from filecrop
put in the firmware folder on Flashtool
- flash that kernel, so you get your phone in 2.1
- root your phone with flash tool by clicking the cross icon
-unlock bootloader (remember do not unlock BL for 11w29+)
- flash the kernel
- backup
- factory reset, wipe data, etc
- flash your ROM
Done! :laugh:
hi every1. im new to this kind of thing. i got a notification from cyanogenmod saying that there was an update avalible for my phone. i then downloaded it and installed it using cwm. i chose the default install option and when my phone rebooted itself, its just stuck on the sony ericsson logo. i know this is called a bootloop but i tried to boot into cwm (by rapidly pressing back when the SE logo appears) but nothing hapened. i took the battery out and when i went ot press the power button the phone turned no itself and is just stuck at the SE logo. can some1 pls help me :-(
s3nbon5akura said:
hi every1. im new to this kind of thing. i got a notification from cyanogenmod saying that there was an update avalible for my phone. i then downloaded it and installed it using cwm. i chose the default install option and when my phone rebooted itself, its just stuck on the sony ericsson logo. i know this is called a bootloop but i tried to boot into cwm (by rapidly pressing back when the SE logo appears) but nothing hapened. i took the battery out and when i went ot press the power button the phone turned no itself and is just stuck at the SE logo. can some1 pls help me :-(
Click to expand...
Click to collapse
You should flash using flash tool to solve it
praveenkumarkm8 said:
You should flash using flash tool to solve it
Click to expand...
Click to collapse
how do i do that? sorry about this
s3nbon5akura said:
how do i do that? sorry about this
Click to expand...
Click to collapse
Here read these..
http://forum.xda-developers.com/showthread.php?t=1755215
Hit thanx if it helped..
Sent from my LEWA using xda premium
And here's the .ftf file of stock rom...
Sent by the walking walkman..
BlackRabbit1703 said:
relax dude!
maybe you can try this!
- first download X8 E15i 2.1.1.C.0.0._un.ftf from filecrop
put in the firmware folder on Flashtool
- flash that kernel, so you get your phone in 2.1
- root your phone with flash tool by clicking the cross icon
-unlock bootloader (remember do not unlock BL for 11w29+)
- flash the kernel
- backup
- factory reset, wipe data, etc
- flash your ROM
Done! :laugh:
Click to expand...
Click to collapse
Thanks for ur information, I tried all those steps mentioned above. Now my phone is working fine. Now I installed GingerDX 028b

I bricked my XZ :(

Please help guys. I tried flashing ROM using the instructions on the front page for locked bootloader and my phone froze on formatting /system, I restarted phone and it is just stuck on Sony. I have tried holding power and volume up it does nothing except restart the device. My PC won't recognise it to do any repairs. Any ideas?
Keep pressing vol up + power for 15 sec till the phone shutdown.
Use flashtool to flash a stock ftf firmware.
Sent from my C6602 using xda premium
It just ends up vibrating for three times and restarting back to Sony screen?
Weird this should turn off the phone.
Is the phone plugged to a usb?
Sent from my C6602 using xda premium
Ok thanks I have it turned off now. How do I flash with it off with flashtools?
Download flashtool from development section,and an ftf stock firmware.
Put the ftf file in flashtool/firmware folder.
Install xperia z drivers,you find it in flashtool/drivers
Click on flash,choose the ftf and wait the the pop up telling you to connect your phone by holding volume down and connecting the usb.
Sent from my C6602 using xda premium
Thanks so much mate... Big thanks
gm007 said:
Download flashtool from development section,and an ftf stock firmware.
Put the ftf file in flashtool/firmware folder.
Install xperia z drivers,you find it in flashtool/drivers
Click on flash,choose the ftf and wait the the pop up telling you to connect your phone by holding volume down and connecting the usb.
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Is there a way in this situation to boot into CWM recovery mode, because I have same problem but I have a backup
p.s. while I booting the phone, the LED didn't light up
mannok said:
Is there a way in this situation to boot into CWM recovery mode, because I have same problem but I have a backup
p.s. while I booting the phone, the LED didn't light up
Click to expand...
Click to collapse
I don't know if there is an easier way cause i didn't tried the recovery available.
All you can do is doing all steps again and install the recovery than restore your backup.
Sent from my C6602 using xda premium
gm007 said:
I don't know if there is an easier way cause i didn't tried the recovery available.
All you can do is doing all steps again and install the recovery than restore your backup.
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
thanks... btw i didnt unlock the bootloader yet, if i use the flashtools to flash back to the stock rom, will i break the warranty?
mannok said:
thanks... btw i didnt unlock the bootloader yet, if i use the flashtools to flash back to the stock rom, will i break the warranty?
Click to expand...
Click to collapse
No
Sent from my C6602 using xda premium
i may have bricked mine too
gm007 said:
No
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
ok so i was stupidly messing around with my fastboot cwm interface menu`s
and i decided ,somehow that it was a good idea to try and install the jellybean 4.2.2
firmware on my device so i entered the install from sdcard menu without even thinking much about it i located the .zip file and installed it and clicked reboot and then absolutley nothing but the boot vibration went off and the screen stays black and it is stuck here . so i used to old powr+ vol up for 3-15 secs and waited for the double vibration and still nothing happens .so im stuck.
sorry for the long post but i`m in a panic as this phone is fairly new about 1 month old and i had already rooted and unlocked boot loader on it so .i hope the info helps you to help me
please respond asap :fingers-crossed:
rix0400 said:
ok so i was stupidly messing around with my fastboot cwm interface menu`s
and i decided ,somehow that it was a good idea to try and install the jellybean 4.2.2
firmware on my device so i entered the install from sdcard menu without even thinking much about it i located the .zip file and installed it and clicked reboot and then absolutley nothing but the boot vibration went off and the screen stays black and it is stuck here . so i used to old powr+ vol up for 3-15 secs and waited for the double vibration and still nothing happens .so im stuck.
sorry for the long post but i`m in a panic as this phone is fairly new about 1 month old and i had already rooted and unlocked boot loader on it so .i hope the info helps you to help me
please respond asap :fingers-crossed:
Click to expand...
Click to collapse
Did you have enough battery before flashing?
Did you tried flashtool?
Sent from my C6603 using xda premium
rix0400 said:
ok so i was stupidly messing around with my fastboot cwm interface menu`s
and i decided ,somehow that it was a good idea to try and install the jellybean 4.2.2
firmware on my device so i entered the install from sdcard menu without even thinking much about it i located the .zip file and installed it and clicked reboot and then absolutley nothing but the boot vibration went off and the screen stays black and it is stuck here . so i used to old powr+ vol up for 3-15 secs and waited for the double vibration and still nothing happens .so im stuck.
sorry for the long post but i`m in a panic as this phone is fairly new about 1 month old and i had already rooted and unlocked boot loader on it so .i hope the info helps you to help me
please respond asap :fingers-crossed:
Click to expand...
Click to collapse
Sounds to me like you haven't flashed the kernel required for 4.2.2 (I am presuming you were on a stock/custom Sony ROM before)
If you flash 4.2.2 you also need to flash the kernel specific to the ROM you've tried to flash using fastboot commands.
To do that you need to have the correct XZ drivers installed, and have adb/fastboot working
gm007 said:
Did you have enough battery before flashing?
Did you tried flashtool?
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
yes i did have enough BATT and no i have not used any flashtool yet as im not sure which to use and i did have a custom romor kernel it was a doomlord one but i just did not take the correct steps and so i was wondering how to undo this ?or just start again (factory reset)
---------- Post added at 08:00 PM ---------- Previous post was at 07:54 PM ----------
rix0400 said:
yes i did have enough BATT and no i have not used any flashtool yet as im not sure which to use and i did have a custom romor kernel it was a doomlord one but i just did not take the correct steps and so i was wondering how to undo this ?or just start again (factory reset)
Click to expand...
Click to collapse
also the phone just does not boot at all i can hardboot as much as i like the screen stays blank and the notification led dont do anything it only shows the red led wen i plug in the usb to indicate charging.
Use flashtool and flash a stock ftf firmware.
Read this could help http://forum.xda-developers.com/showthread.php?t=2229250
Sent from my C6603 using xda premium
gm007 said:
Use flashtool and flash a stock ftf firmware.
Read this could help http://forum.xda-developers.com/showthread.php?t=2229250
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
thanks i will try it and update you after but i think it will work ,thanks alot:good: for the help

Please help Xperia Z stuck on Sony Logo boot loop

help please phone has been rooted has no recovery installed not sure it has locked bootloader or not just got phone last week rooted the phone to try and hide the on screen buttons when playing games which worked fine untill now been trying for 3 days searching the forums for help
swithched phone off then whent to power it back up it shows SONY logo then black screen then back to sony logo
tied sony update software it just says your phone has the latest version installed no options to recover
next tried sony pc companion it get to where it says downloading then comes up with a error saying sony has not got the software for the connected device please try again later
then i tried flash tool using fastboot as i can get the blue light by holding vol up then connceting usb i downloaded the official uk stock firmware i extracted the 3 main files from the ftf file which were kernal system and userdata flashed then but still the same now when i put phone back into fast boot flashtool does not show it being there put windows shows s1 boot fastboot connected as a usb device
please please help i am getting desparite now think am running out of ideas i have rooted and flashed many samsungs s2 s3 note note 2 htc and had no problems at all its my first sony phone
To flash a ftf file you need to go into flash mode volume down green led and flashtool will do the rest
You are going into fastest which is used for kernels
Sent from my C6603 using xda premium
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
gm007 said:
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
just followed the link posted thanks i select flash mode then the stock firmware then it tells me to hold vol down and plug usb cable in then the log just sayes device conneted in flash mode and does nothing else untill the phone reboots its self any more ideas
Have you selected to flash file?
Sent from my C6603 using xda premium
Maddhouse said:
Have you selected to flash file?
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
yeah m8 click flash select flashmode select c6603 which i put in the firmware folder click flash it asked to connect the device holding vol down then plug usb cable in which i do then flash tool says device connected in flash mode and goes no further
pie2007 said:
yeah m8 click flash select flashmode select c6603 which i put in the firmware folder click flash it asked to connect the device holding vol down then plug usb cable in which i do then flash tool says device connected in flash mode and goes no further
Click to expand...
Click to collapse
okay then did you install drivers for flashmode?
Edit: Are you using pc companion or Sony Update Service
pie2007 said:
yeah m8 click flash select flashmode select c6603 which i put in the firmware folder click flash it asked to connect the device holding vol down then plug usb cable in which i do then flash tool says device connected in flash mode and goes no further
Click to expand...
Click to collapse
got it sorted was holding vol dwn for to long as soon as the green light come on i let go and it worked thanks everyone
pie2007 said:
got it sorted was holding vol dwn for to long as soon as the green light come on i let go and it worked thanks everyone
Click to expand...
Click to collapse
Good good just to remember in future if you phone reboots on sony logo it is a kernel problem if it reboots on xperia screen it is a system problem just to keep that in mind and if you are on a stock rom then they are ODEX so you will need to find mods which will work not DEODEX other wise you will get bootloop
Pls help ex z
PLEASE HELP
my xperia Z , c6602 , got new update .244
tried to update using fone , downloded 175 mb and restrted, updating proceess came up (android logo) automatically rebooted when the progress bar about 75% , not updated same old .423
tried 2 times same issue,
then i tried using sony pc companin(win8), donloaded updated and strted update process, progress bar 90% came up error that update failed,
disconnect phone,
NOW phone didnt boot up
only SONY logo coming and switchs off.
pls help
Ok guys I am facing a problem.
I am coming from 6.0 when I update to 6.5.0 and restart the phone it gets stuck at sony logo. Have flashed the correct kernel ie 101 still the same any suggestions?
Jay_B said:
Ok guys I am facing a problem.
I am coming from 6.0 when I update to 6.5.0 and restart the phone it gets stuck at sony logo. Have flashed the correct kernel ie 101 still the same any suggestions?
Click to expand...
Click to collapse
I suggest you more thoroughly describe your problem. Version 6.0 and 6.5.0 of what, exactly?
Sent from my C6603 using Tapatalk
Sorry wrong forum
facepalm.jpg
Sent from my C6603 using Tapatalk
Jay_B said:
Sorry wrong forum
Click to expand...
Click to collapse
Yes, but are you talking about Existenz v6 and about update package version v6.5?
When yes, go to recovery, select clean to install new rom, wipe cache, dalvik cahe and install Existenz v6. Then reboot and download Existenz v6.6 (latest update, which fixes many bugs) and flash it. Flashing without wiping should work, but i recommend to wipe cache and dalvik
My xperia stuck in boot loop
Maddhouse said:
Good good just to remember in future if you phone reboots on sony logo it is a kernel problem if it reboots on xperia screen it is a system problem just to keep that in mind and if you are on a stock rom then they are ODEX so you will need to find mods which will work not DEODEX other wise you will get bootloop
Click to expand...
Click to collapse
my xperia c3 stuck in bootloop when it boots it display sony logo then vibrate once with purple LED blink then it boot again display sony logo and
so on... [ it stuck in bootloop when i am tried to install/flash custom recovery (philz recovery)] [i can open recovery still ]
please help me it i flash stock rom can it fix boot loop?
My sony xperia z c6602 got stuck in sony logo boot loop. I was trying to install xperia z dual recovery for locked bootloaders but my boot loader is unlocked. As the process of recovery installation finished my phone started rebooting but it shows the sont logo and then power off again it shows the sony logo and power off this thing keep on going. Please help me
My phone is rooted with superuser and is working on android lollipop and recovery is not installed

My Xperia Z can't boot!

I need some helps plz.
my Z had bootloader unlocked and I had flash DooMkernel and on the EXCELSUS Z v2.5.1 rom.
At the first, everything work perfect till yesterday I turn off my phone.
Then it didn't boot anymore.
Here is my situation:
1. When I press power button, it had a vibration and nothing on screen.
2. I long press the button and it gave me regular vibrations and also nothing on the screen.
3. When I try to charge it, it had red LED on and off all the night.
4. It can still go into flashmood and fastboot.
5. I try to use flashtool to flash .434 ftf. Flashtool told me "ERR_SEVERITY="MINOR";ERR_CODE="0026";ERR_DYNAMIC="Write TA failed"
6. I try to use sony update service to fix it and it told me your device doesn't have new update.
7. I try to use fastboot to reflash kernel and failed as well.
Any idea? Someone plz help me!
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
gm007 said:
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
I have try it. And when It going to flash then appear a line in red "ERROR - ERR_SEVERITY="MINOR";ERR_CODE="0026";ERR_DYNAMIC= "Write TA failed"
jason57 said:
I have try it. And when It going to flash then appear a line in red "ERROR - ERR_SEVERITY="MINOR";ERR_CODE="0026";ERR_DYNAMIC= "Write TA failed"
Click to expand...
Click to collapse
Are you sure you followed the instructions carefully?
Do you have flashtool beta6?
Sent from my C6603 using xda premium
gm007 said:
Are you sure you followed the instructions carefully?
Do you have flashtool beta6?
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
I follow it and do again.
But it still failed
Sent from my Xperia X10 using xda app-developers app
Did you tried.flashtool beta4? Or another firmware?
Move your issue to flashtool' thread.
Sent from my C6603 using xda premium
Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
Please help If anybody has experienced
Thank you in advance
jason57 said:
I follow it and do again.
But it still failed
Click to expand...
Click to collapse
Try this, when you start flashing, press-release the power button multiple times until it finish flashing, this is something that is actually happening on my xperia z, and sometimes it just starts redlight and vibrate 3 times, reboot, if i press-release press-release fast multiple times, it just dont reboot.
Regards!
It works
vodanhdaisu said:
Please help. I've just flash DoomLord v13 kernel via CWM: after install the zip file, I choose Reboot to system but my phone does not boot afterward
I push power button, the phone vibrates but does not awake
I connect my phone to usb, the red light blinks only
Please help If anybody has experienced
Thank you in advance
Click to expand...
Click to collapse
First of all, Flash Kernel only if have unlocked bootloader :/ i encountered the same issue. If so you need to flash the stock ROM - Please find the stock ROM below in link below.
http://forum.xda-developers.com/showpost.php?p=38637922&postcount=2
Use Beta6 Flashtool to flash the ROM.
It will worl for sure

[Q] Help flashed tilal6991's CM 10.2 [4.3] [XPERIA T] cant go back to cm 10.1

Hello everyone
I am a noob.
I have just recently flashed tilal6991's CM 10.2 [4.3] [XPERIA T] rom onto my Xperia T. I know it is a working progress and it works really fast on my phone.
I had decided that after trying it out I would wait till a nightly came out for it. Only thing is I can no longer access CWM by starting up phone and repeatedly pressing down volume. it justs keep screen flickering on a blank screen until I hold up volume and power button to reboot phone.
Can someone please tell me an idiot proof process of reinstalling cm 10.1 onto the phone?
I used CWM to install teh rom.
Many thanks in advance
Just flash a stock ftf using flashtool.
Our flash a stock kernel (doomkernel is good) then flash a stock based custom Rom in recovery (I suggest mine Rom-assaye)
You cannot repair in pccompanion because you have unlocked your bootloader
Sent from my LT30p using xda premium
gregbradley said:
Just flash a stock ftf using flashtool.
Our flash a stock kernel (doomkernel is good) then flash a stock based custom Rom in recovery (I suggest mine Rom-assaye)
You cannot repair in pccompanion because you have unlocked your bootloader
Sent from my LT30p using xda premium
Click to expand...
Click to collapse
Thanks for the quick reply. downloading flash tool now. I will give your rom a go.
Do I need to download the ftf from flashtools website? I noticed they have 9.1.A.1.140 Customized CE1 firmware.
No, just one from the all in one thread, but that one seems fine.
Make sure you use the flash tool from the first post in the dev section
Sent from my LT30p using xda premium
you dont need to flash stock FTF
just flash this kernel via flashtool
http://goo.im/devs/tilal6991/kernels/mint/boot-cm-10.1-test-28072013-take2.img
and you will be able to enter recovery and then flash what you need... this way is more quicker..
Apologies, I misread the op, I thought he wanted to go back to stock.
Yes, flashing a kernel (doomkernel will do) with recovery then the . Zip for cm10 will do the trick much quicker.
Edit
Or flash the kernel then restore the backup of your cm10 Rom that you made before flashing a new Rom
Sent from my LT30p using xda premium
thanks for all the help guys.
I have a new problem. the phone will not stay in fast boot mode and fast tool just keeps saying awaiting device. i dont know what to do. I hold down power and volume up buttons when putting the micro usb in. I get the 3 vibration in a row and then i let go of buttons. blue light comes on for a few seconds and then goes off.
Any ideas?
open flashtool and select flash icon then fastboot mode
turn off your phone hold power +volume down till you get 3 vibrations on a row
now connect the phone by holding only up volume when connecting cable
then select SELECT kernel to flash switch to IMG extension and select kernel after 5 second it should be flashed
now turn on your phone go to recovery and flash what you want
Guys you are all awesome.
finally got it sorted. took me til 2230 GMT. It was the cursed Windows 8. it was not letting me install sony fastboot drivers. once i switched off the function to stop me installing my own drivers, I was able to install fastboot drivers and 30 secs later I was in CWM.
Once again guys you are awesome.

Categories

Resources