Well do not think that this thread is one among others. It's my experience when i messed up with my Razri. I wish I had this before, so I'm sharing it with you !
Every has his experience and a way to do it, so this is mine
First I searched everywhere, as you already did, the technique is globally the same but one important thing was missing and I had to get my Razri ON, it's an "Intel" !
I tried this app to install the needed drivers and to flash firmware, and I tried also this
Just let me explain what i had before the "softbrick" just to assure you that your Razri is not dead and it's up to you to bring it up from the dead and you can do that
I softbricked it by rooting my JB android with ICS, I messed up, in you case might be different but you are here cause we all had the same problem
Well, if your Razri Motorola XT890 cannot boot (or keeps rebooting with no end), charging the battery is [im]possible. Below is a quick how-to
RSD Lite detects the Razri as a "MEDFIELD" device. You can use RSD Lite to flash your phone whith a new Android Image [JB here, for "JB 4.1.2" I choose "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip"] but this is doable only after getting to the fastboot menu
1. Install EXE drivers for the "MEDFIELD" device
2. Run BAT file and follow the instructions inside
3. You might restart you Razri
You need to use the wright ifwi & dnx file, so I included those for JB (and not for ICS and if you did you will get "Service code corrupt" error but don't worry you have just to get the good version of ifwi&dnx for your android version)
Just to say, for everyone who has this trouble, and thinks that his Razri is dead, good new It is not, but remember that to make this work that fastboot menu is in there, somewhere just use the right combination, no matter what you have on the screen (Bootloader Unlocked screen or nothing at all just a black screen)
This is a little How-To:
Power botton+Volume Down botton at the same time
Wait until the screen flashes or the green led light to flash the immediately release the Power button while keeping the Volume down pushed (do not release ever) until the fastboot menu appears
Good Luck
service required code corrupt
DoxyMarket said:
Well do not think that this thread is one among others. It's my experience when i messed up with my Razri. I wish I had this before, so I'm sharing it with you !
Every has his experience and a way to do it, so this is mine
First I searched everywhere, as you already did, the technique is globally the same but one important thing was missing and I had to get my Razri ON, it's an "Intel" !
I tried this app to install the needed drivers and to flash firmware, and I tried also this
Just let me explain what i had before the "softbrick" just to assure you that your Razri is not dead and it's up to you to bring it up from the dead and you can do that
I softbricked it by rooting my JB android with ICS, I messed up, in you case might be different but you are here cause we all had the same problem
Well, if your Razri Motorola XT890 cannot boot (or keeps rebooting with no end), charging the battery is [im]possible. Below is a quick how-to
RSD Lite detects the Razri as a "MEDFIELD" device. You can use RSD Lite to flash your phone whith a new Android Image [JB here, for "JB 4.1.2" I choose "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip"] but this is doable only after getting to the fastboot menu
1. Install EXE drivers for the "MEDFIELD" device
2. Run BAT file and follow the instructions inside
3. You might restart you Razri
You need to use the wright ifwi & dnx file, so I included those for JB (and not for ICS and if you did you will get "Service code corrupt" error but don't worry you have just to get the good version of ifwi&dnx for your android version)
Just to say, for everyone who has this trouble, and thinks that his Razri is dead, good new It is not, but remember that to make this work that fastboot menu is in there, somewhere just use the right combination, no matter what you have on the screen (Bootloader Unlocked screen or nothing at all just a black screen)
This is a little How-To:
Power botton+Volume Down botton at the same time
Wait until the screen flashes or the green led light to flash the immediately release the Power button while keeping the Volume down pushed (do not release ever) until the fastboot menu appears
Good Luck
Click to expand...
Click to collapse
hello good afternoon,
Could you tell me if it corrects this type of unbrick?
service required code corrupt. appears on the black screen.
already thanks.
DoxyMarket said:
Well do not think that this thread is one among others. It's my experience when i messed up with my Razri. I wish I had this before, so I'm sharing it with you !
Every has his experience and a way to do it, so this is mine
First I searched everywhere, as you already did, the technique is globally the same but one important thing was missing and I had to get my Razri ON, it's an "Intel" !
I tried this app to install the needed drivers and to flash firmware, and I tried also this
Just let me explain what i had before the "softbrick" just to assure you that your Razri is not dead and it's up to you to bring it up from the dead and you can do that
I softbricked it by rooting my JB android with ICS, I messed up, in you case might be different but you are here cause we all had the same problem
Well, if your Razri Motorola XT890 cannot boot (or keeps rebooting with no end), charging the battery is [im]possible. Below is a quick how-to
RSD Lite detects the Razri as a "MEDFIELD" device. You can use RSD Lite to flash your phone whith a new Android Image [JB here, for "JB 4.1.2" I choose "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip"] but this is doable only after getting to the fastboot menu
1. Install EXE drivers for the "MEDFIELD" device
2. Run BAT file and follow the instructions inside
3. You might restart you Razri
You need to use the wright ifwi & dnx file, so I included those for JB (and not for ICS and if you did you will get "Service code corrupt" error but don't worry you have just to get the good version of ifwi&dnx for your android version)
Just to say, for everyone who has this trouble, and thinks that his Razri is dead, good new It is not, but remember that to make this work that fastboot menu is in there, somewhere just use the right combination, no matter what you have on the screen (Bootloader Unlocked screen or nothing at all just a black screen)
This is a little How-To:
Power botton+Volume Down botton at the same time
Wait until the screen flashes or the green led light to flash the immediately release the Power button while keeping the Volume down pushed (do not release ever) until the fastboot menu appears
Good Luck
Click to expand...
Click to collapse
Hi
do you have any solution for "service required code corrupt" plz
thanx
If you've tried to root your JB Motorola RAZR I with the ICS root-method don't worry. The ICS-root-method flash a unsave boot image, which is for the ICS firmware. That's why the RAZR with JB have problems to boot.
To make everything working again, you need:
- RAZR I PC driver
- fastboot (PC program)
- the right boot image for your JB version. (e.g. retail.EU) (download the right version from firmware-thread and search for a file "boot.img" )
If you have everything prepared do the following things:
- start your RAZR I (make sure, that it doesn't boot into bootloop)
- connect your RAZR I to your PC
- on PC start a command line/terminal and (for windows users) navigate in the directory with the fastboot.exe and make sure that the boot.img file is in the same directory
(Linux users navigate into the directory with the boot.img)
- type: fastboot flash boot boot.img
- wait until it's done
- reboot the device by typing: fastboot reboot
And that's it. Your personal data won't be touched, everything is like it was before.
Gesendet von meinem XT890 mit Tapatalk 4
Try this
sysmanin said:
Hi
do you have any solution for "service required code corrupt" plz
thanx
Click to expand...
Click to collapse
It's probably beacause tou updated your Formware with the wrong version, try this out:
You need to use the wright ifwi & dnx file, so I included those for JB (and not for ICS and if you did you will get "Service code corrupt" error but don't worry you have just to get the good version of ifwi&dnx for your android version) ==> You can get it from de XML file form sbf.droid-developers.org/smi/list.php it depends in which android version you were befor, in my case i took "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip"
So you have to Unzip it and there you'll find the ifwi & dnx files
Nice
cupioscire said:
If you've tried to root your JB Motorola RAZR I with the ICS root-method don't worry. The ICS-root-method flash a unsave boot image, which is for the ICS firmware. That's why the RAZR with JB have problems to boot.
To make everything working again, you need:
- RAZR I PC driver
- fastboot (PC program)
- the right boot image for your JB version. (e.g. retail.EU) (download the right version from firmware-thread and search for a file "boot.img" )
If you have everything prepared do the following things:
- start your RAZR I (make sure, that it doesn't boot into bootloop)
- connect your RAZR I to your PC
- on PC start a command line/terminal and (for windows users) navigate in the directory with the fastboot.exe and make sure that the boot.img file is in the same directory
(Linux users navigate into the directory with the boot.img)
- type: fastboot flash boot boot.img
- wait until it's done
- reboot the device by typing: fastboot reboot
And that's it. Your personal data won't be touched, everything is like it was before.
Gesendet von meinem XT890 mit Tapatalk 4
Click to expand...
Click to collapse
Worth testing. Very useful for people having the issue
Hello everyone,my phone had bricked;
I was on jelly bean 4.1.2 , Systemversion : 91.2.26001.XT890.Retail.en.EU ( Firmwareupgrade)
my question is ,using this method wich ifwi & dnx file could i choose ?
Thanks in advance
DoxyMarket said:
Well do not think that this thread is one among others. It's my experience when i messed up with my Razri. I wish I had this before, so I'm sharing it with you !
Every has his experience and a way to do it, so this is mine
First I searched everywhere, as you already did, the technique is globally the same but one important thing was missing and I had to get my Razri ON, it's an "Intel" !
I tried this app to install the needed drivers and to flash firmware, and I tried also this
Just let me explain what i had before the "softbrick" just to assure you that your Razri is not dead and it's up to you to bring it up from the dead and you can do that
I softbricked it by rooting my JB android with ICS, I messed up, in you case might be different but you are here cause we all had the same problem
Well, if your Razri Motorola XT890 cannot boot (or keeps rebooting with no end), charging the battery is [im]possible. Below is a quick how-to
RSD Lite detects the Razri as a "MEDFIELD" device. You can use RSD Lite to flash your phone whith a new Android Image [JB here, for "JB 4.1.2" I choose "CFC_9.8.2I-50_SMI-26_S7_USASMIJBRTEU.xml.zip"] but this is doable only after getting to the fastboot menu
1. Install EXE drivers for the "MEDFIELD" device
2. Run BAT file and follow the instructions inside
3. You might restart you Razri
You need to use the wright ifwi & dnx file, so I included those for JB (and not for ICS and if you did you will get "Service code corrupt" error but don't worry you have just to get the good version of ifwi&dnx for your android version)
Just to say, for everyone who has this trouble, and thinks that his Razri is dead, good new It is not, but remember that to make this work that fastboot menu is in there, somewhere just use the right combination, no matter what you have on the screen (Bootloader Unlocked screen or nothing at all just a black screen)
This is a little How-To:
Power botton+Volume Down botton at the same time
Wait until the screen flashes or the green led light to flash the immediately release the Power button while keeping the Volume down pushed (do not release ever) until the fastboot menu appears
Good Luck
Click to expand...
Click to collapse
Hi! i have a chance to revive my razr i?
HI guys! I have a problem.
i have downgraded with this rom:http://forum.xda-developers.com/showthread.php?t=2294653
and after i tried to flash two rom with rsd lite:
CFC_signed_customer_8.7.1I-110_IFW-31_RTGB.xml
CFC_8.7.1I-110_IFW-39_S7_UCASMI01E1017.0R_USASMIICSRTGB_P042_A005_S1F F_fb.xml
now the phone is locked , in the screen is write: service required code corrupt
and the green led .. can help me please?
It will work!!... keep trying
peter971215 said:
Hi! i have a chance to revive my razr i?
HI guys! I have a problem.
i have downgraded with this rom:http://forum.xda-developers.com/showthread.php?t=2294653
and after i tried to flash two rom with rsd lite:
CFC_signed_customer_8.7.1I-110_IFW-31_RTGB.xml
CFC_8.7.1I-110_IFW-39_S7_UCASMI01E1017.0R_USASMIICSRTGB_P042_A005_S1F F_fb.xml
now the phone is locked , in the screen is write: service required code corrupt
and the green led .. can help me please?
Click to expand...
Click to collapse
Check this for your problem http://forum.xda-developers.com/showthread.php?t=2134391
You must use the boot.img for you Android version (boot.img isn't the same for ICS, JB or GB)
DoxyMarket said:
Check this for your problem http://forum.xda-developers.com/showthread.php?t=2134391
You must use the boot.img for you Android version (boot.img isn't the same for ICS, JB or GB)
Click to expand...
Click to collapse
i can't get fastboot, the phone go on "service required code corrupt" screen with the green led on and nothing..
Try again
peter971215 said:
i can't get fastboot, the phone go on "service required code corrupt" screen with the green led on and nothing..
Click to expand...
Click to collapse
This would help http://forum.xda-developers.com/showthread.php?t=2220242
DoxyMarket said:
This would help http://forum.xda-developers.com/showthread.php?t=2220242
Click to expand...
Click to collapse
Nothing... the phone show Only the green led and nothing.....
Again
peter971215 said:
Nothing... the phone show Only the green led and nothing.....
Click to expand...
Click to collapse
Charge the phone
And try to get to Fastboot menu
help
Hello!
Pozhausta tell where to get the files (ifwi and dnx) of this firmware (CFC_8.7.1I-110_IFW-39_S7_UCASMI01E1017.0R_USASMIICSRTGB_P042_A005_S1F F) and then archive them in there?
You simply saved my life!
I did the whole process, but now i'm stuck on (flash boot "boot_signed") in RSD, any ideas?
renatotec said:
I did the whole process, but now i'm stuck on (flash boot "boot_signed") in RSD, any ideas?
Click to expand...
Click to collapse
You probably did not use the right image for you phone
peter971215 said:
Nothing... the phone show Only the green led and nothing.....
Click to expand...
Click to collapse
Have you already found a solution mate ?
GRACIAS!!!
Instalé una ROM brasilera porque se había brickeado, era JB, luego instalé la ICS y quedo muerto, encontre tu post primero y funcionó perfecto, mil gracias!!!!
Motorola XT890 Razr i
Hi, I tried to follow your instructions but so far my cell phone is still death. when I run the bat file I got this error message. libusB0.dll not found. also I don't know how RDS lite tools detects my cel. it is not working as the same manner as you showed us. can you help me to find a way to unbrick my cell phone.
thanks
Related
Well, this is embarrassing...
Current Status:
After a factory wipe and reinstalling (phone was OK after that) and an OTA, i managed to nearly brick my razr.
Currently every time i start it lands in fastboot (according to RSD Lite mode S) with the message fastboot reason: flash failed
after 'fastboot reboot-bootloader' i can operate the menus but only changing the console type and power off work, everything else results in a freeze.
Reflashing CFC_signed_customer_8.7.1I-110_IFW-DE-32_O2DE.xml.zip or 31 is not possible, since the OTA update apparently changed boot[1], gpt[2], and few other things to version "8.7.1I-110_IFW-DE-39" (the only thing i can flash from those are the recovery partitions and from the new one the gpt.bin)
Custom fastboot also does not work, since i'm not eligible according to Motorola ( tis was my first thought to check the custom boots & finally unlock the bl *g*)
I already ordered the factory adapter (hey, you never know, when you're gonna need one) & My Battery still has ~3.9v left, so i think a few tries should not hurt that much : >
TL;DR, Here's my question:
1) is it possible to patch the images provided in CFC_signed_customer_8.7.1I-110_IFW-DE-32_O2DE.xml.zip with the binary patches from Blur_Version.81.5.32002.XT890.O2.en.DE (updates to: 8.7.1I-110_IFW-DE-39_O2DE) and then maybe re-flash them to get my razr back from the near death zone?
2) should i hope and pray that Motorola announces JB upgrade and provides us with the full system images within the next few days?
3) can anyone find a full system image / full update with the version: 8.7.1I-110_IFW-DE-39_O2DE ?
References:
[1]: from update-script:
assert(apply_patch("MTD:boot:11534336:affeb8868070f6e6f061143b662e03b5bf65b2f3:11534336:19bf404a393a50d08a809affd45df5692e36e1db",
"-", 19bf404a393a50d08a809affd45df5692e36e1db, 11534336,
affeb8868070f6e6f061143b662e03b5bf65b2f3, package_extract_file("patch/boot.img.p")));
[2]: There is a brand new gpt.bin file within the OTA package
Cheerio,
Andy
The Problem is, without unlocking your Bootloader, you can't downgrade the Boot. img.
I would suggest you to grap the 39002 O2 Homemade Fastboot from Mattlgroff and flash only the Boot. img out of it. If you're an lucky guy, you're able to boot after that.
An Guy from my Home Forum tried the downgrade from 40002 today with an locked boot loader. RSD stopped @ point 1 GPT. His solution to boot his phone again was to flash the gpt.bin out of the 40002 OTA .zip.
So your only chance to get your phone back is to find flashable Images from the 39002 or 40002 because of the secure Level.
The easiest way is to unlock the device, I can downgrade to any FW. Or you'll have to wait for an updated Fastboot File to flash with RSD.
Hokay, apparently i had a typo yesterday when i tried to unlock the bootloader
But, now after trying the custom fastboot, i still land in fastboot with reason: Sticky bit fastboot
and all other menus still cause a freeze : /
If you're now unlocked, get an EU FW, regardless what Version. Open the XML with Notepad + or any similar Programm and delete ONLY the complete Line that contains MOTOBOOT. Save the XML and start RSD 6.1.4.
After that you should be good to go.
HSD-Pilot said:
If you're now unlocked, get an EU FW, regardless what Version. Open the XML with Notepad + or any similar Programm and delete ONLY the complete Line that contains MOTOBOOT. Save the XML and start RSD 6.1.4.
After that you should be good to go.
Click to expand...
Click to collapse
Purrrrfect, i owe you a bottle of wine.
Problem solved : >
Yeah, I'm glad I could help you out... RazR I Nr. 8 > Strike
bricked
hi guys the same thing happen to me i cant use rsd or fastboot because it says stigki bit fastboot.and in rsd it fails tryin to flash boot. im in mexyco i was using the new ota for 30006 that would be 40002. i just try to erASE THE BOOT LINE AND IT DIDNT WORKIT SAID THE SAME. HELP
So you're on 40002 and tried to flash back with RSD and your Bootloader is locked?
RSD failed on step one, right?
brick
Yes sir. Iwas on 40002 and with the rsd i was trying to go back to stock 30006,but on step 3 it says fail. Then i try to fastboot 40002 but it tqkes me again to fastboot and its freezes when i try to open a command like normal boot or recovery. I tried to eras the lineinside of motoboot where it says motoboot like the guy you just helped. But in my case still gets stuck on step 3in the rsd. So could you send me images of how erase the line of motoboot on text editor?? Im boot unlocked.
You mean 31006...Here ya go (unpack it > i can't attach an .xml)
Thank u sir. So i flash this on rsd,right? Vause i think that this is the one i have.the last digits are 31 on mine an starts cfc . Something else. I cant really tell u cause im at work but tonight i'll try ur method. Hope it works.
http://www.mediafire.com/download.php?ud9kowzk1uw2bcb
Use RSD 6.1.4 and copy the xml into the fastbootfolder. That's all...BTW: Charge your battery if possible or hope you got enough juice!
unbricked
thank you sir. everything like new!!!!!!!!
i"ll buy u some beers.
my razr i is workin now but i cant update the ota for the 31006 thats going to take me to 40002??
You're trying to update regular over the Phone or the manual over the leaked Update.zip? If you're trying it over the leaked zip, than beware. There's one if you're coming from 31006 and one from 32002.
Sent from my XT890
I go into software update, then i download the file, its like 50mb. Then it goes into rwcovery but the android dies and says aborted. So then i tried in recovery mode to flash zip blur ota 310006 but it happen the same. So i decided to stay in mis rom the 31006 from sept. But i was wondering if now i could flash in fastboot another rom like 40002? I saw u guy have the ota update for that rom.
---------- Post added at 03:04 PM ---------- Previous post was at 02:07 PM ----------
I go into software update, then i download the file, its like 50mb. Then it goes into rwcovery but the android dies and says aborted. So then i tried in recovery mode to flash zip blur ota 310006 but it happen the same. So i decided to stay in mis rom the 31006 from sept. But i was wondering if now i could flash in fastboot another rom like 40002? I saw u guy have the ota update for that rom.
Thank you - you're the best
HSD-Pilot said:
If you're now unlocked, get an EU FW, regardless what Version. Open the XML with Notepad + or any similar Programm and delete ONLY the complete Line that contains MOTOBOOT. Save the XML and start RSD 6.1.4.
After that you should be good to go.
Click to expand...
Click to collapse
My RAZR i works again thanks to HSD-Pilot. You saved my life.
THANK YOU
Roman
how found fastbootfolder me friend, sorry im newbie and me phone is death, please help
Razr i black screen after update phone not getting on
After i have unlock bootloader and root the phone....i have to do a fresh update to last Jelly Bean....phone have got turno of for starting insatll the update....and have rest like that...............When i press Power or Power and Vol Down is just doinf a short vibrate and the Notification led stay On for 10 sec after led OFF and a short vibrate.....>>Connecting to PC no getting any device on RSD or Fastboot and in Windows detect as a MEDFIELD device for wich no driver i found anywhere.........Phone was having 100% POWER before doing all this....adn i have try on several Pc with diferent Windows and diferent 32 or 64 bit with all RSD, drivers Sdk, etc installled and same results.....if anyone have a ideea how to repair will be a really expert on this modding devices....thank you and ...HELP
Hey guys,
i did stupid things witch my razr i and now i'm completely lost…maybe someone can help?
I've been impatient enough to try to flash the leaked jb rom 3 days ago. That did'nt work
No, whenever i power up the phone it shows the red M logo and nothing happens.
I can power it down by holding vol+down and power for more than 4 seconds.
If i release the keys, it goes back to te red M,
If i keep holding vol+down it boot s into AP fastboot flash mode (secure boot) 20.0f
i can choose recovery and that'll work, but i don't have an update for external storage. rebooting from there leads to red M.
Normal Powerup, Factory and BP Tools are choosable, log says Booting into… but nothing happens after that, i'll stay in fastboot.
Power off works.
I tried to flash various images via »fastboot flash boot/recovery/system«, but nothing worked out.
I flashed the files from Razri_Root_Linux, two files (retail central europe) from here sbf.droid-developers, but nothing helped, every reboot leads to the red M.
I read about RSD-Lite, tried to install it under Win7, got it, but was lost after the Program always complained about an invalid xml.
Since i don't own that machine i went back to my linuxbox where i found sbf_flash, but i don't get it how to put the pieces together (which file/s to use)
Any hints on how to go from here?
[EDIT:] I downloaded 91.2.26001.Retail.en.EU.zip and did all the steps from flashandboot.bat, read
fastboot flash boot
fastboot flash system
fastboot flash recovery
next step ist to select recovery, did this an cwm comes up, sideloaded RAZRiRoot2.zip everything is pisitively quited, no errors are shown.
reboot leads to red M
wiped data/factory reset, reboot
red Logo.
I'm completely lost, please help
[\EDIT]
greetings, D.
I had same problem
Hello.
I had same problem because I did very stupid thing. I flashed homemade JB and because some apps don´t work I tried downgrade my i to ICS back....
My i stucked at the red M then I tried same thing as you and phone still booted into red M.
So I tried in windows cmd and FlashAndRoot.bat from this .zip "91.2.26001.Retail.en.EU - 4.1.2" it did nothing, but I tried to choose in fastboot mode BP Tools, then my i booted and started to flash JB what I can see in command window. Phone was still connected to PC. After next reboot my phone has work normally with JB.
I hope to help you. Let me know.
Lucki
Hi Lucki
thanks for jumping by.
Lucki_X said:
Hello.
So I tried in windows cmd and FlashAndRoot.bat from this .zip "91.2.26001.Retail.en.EU - 4.1.2" it did nothing, but I tried to choose in fastboot mode BP Tools,
Click to expand...
Click to collapse
I tried this, and display on razr i says »Booting into BP Tools mode…«
and nothing more happens, display stays on…
and after some time pc automounts a "cd-rom drive" with some motorola files (Autorun.inf MDMSetup.xml MotorolaDeviceManagerSetup.exe MDMSetup.ini MotorolaDeviceManager_2.2.28)
but it still won't reboot…
i don't know.
Hi.
I had opened command window, "FlashAndRoot.bat" was running (I pressed any key) process was running (it means freezing ) and at this time I chose in fastboot booting into BP tools mode. My phone did restart and after it "FlashAndRoot.bat" process started to flash JB. After flashing my phone is going normally with JB. But some apps don´t work in JB.
Lucki
Lucki_X said:
Hi.
I had opened command window, "FlashAndRoot.bat" was running (I pressed any key) process was running (it means freezing ) and at this time I chose in fastboot booting into BP tools mode. My phone did restart and after it "FlashAndRoot.bat" process started to flash JB. After flashing my phone is going normally with JB. But some apps don´t work in JB.
Lucki
Click to expand...
Click to collapse
Doesn't work. :crying:
since i use linux i opened FlashAndRoot.bat in texteditor and executed the comands from there in terminal
only chance for the script to stop and wait is IMHO(correct-me-if-i'm-wrong) "adb wait-for-device push RAZRiRoot2.zip /sdcard/RAZRiRoot2.zip & adb reboot bootloader"
but that message "Booting into BP Tools mode…" just stays there forever, or does it take longer than 5minutes?
dogo77 said:
but that message "Booting into BP Tools mode…" just stays there forever, or does it take longer than 5minutes?
Click to expand...
Click to collapse
In my case it booted within 10 second and ran.
I am noob, I am writing just my experience. I couldn´t give you another advice, sorry.
I'm not sure how far the real installation went, but i would find Windows computer, get RSD (6.0-6.14) and try to flash ICS first. If failed due to impossibility of downgrading, then try JB. While you are able to boot to Recovery - don't loose hope yet
okaban said:
I'm not sure how far the real installation went, but i would find Windows computer, get RSD (6.0-6.14) and try to flash ICS first. If failed due to impossibility of downgrading, then try JB. While you are able to boot to Recovery - don't loose hope yet
Click to expand...
Click to collapse
Yeah. I'm still stuck at the red logo, or indeed, at a blueish "Bootloader unlocked warnig" message since i was able to install parts of an image from sbf.droid-developers. But flashing always fails while trying to flash system.img_signed.
After reading and trying a lot these last days i think i have to install windows somewhere just to get rsd-lite to run.
sbf_flash for linux didn't work for me and fastboot gives stange warnings about "Invalid sparse file format at header magi"…
so i'll give rsd a try before i give up. As i read in posts by HSDPilot, this is the only tool that works
thanks for your help!
Hi, my best friend she had a HD phone, one day got stuck into the M logo, the only thing I can do is get into the fastboot, no recovery no nothing.. So i try to reinstall the rom, have download several tools but i cant do anything, after several intents to install roms i hace in AP fastboot flash mode, device is unlocked status code 1fastbookt Reason sticky bit factoy_fastboot. for a 2nd time but i can install roms, I dont know if phone bootloader unlock and cant check... I dont know if phone is usb debugging cause it wont load the system. I dont see any internal files from phone I also try rsd lite, but the same it says that it start doing the process but nothing else happen.. any ideas on how to get a rom install there..
thanks
SAME thing..
Please do help us...No recovery...No debugging...stuck at logo..!!
If you don't have an unlocked bootloader, I don't think you can use Myth or RSD to flash an ICS rom over a JB rom.
Did you load the latest Motorola USB drivers? When you connect the phone, run adb to list the devices. Does your phone appear?
not for me doesnt show any devices... and while trying to do other commands always get stuck ad *daemond started succesfully* but doesnt do anything.. also when trying to use motorola device manager it says it will update and never connect to server and close the app.
if i do fastboot commands like reboot-loader it does work it reboots the phone, but if i try to flash something doesnt it doesnt do anything.. i try using mfastboot also and the same happen.
Is there a way to flash a rom or something so i can fix this phone or it is dead?
On the Fastboot screen, if it says UNLOCKED in capitals next to "Device Status:" , then this problem is easily fixable.
Download RSD Lite from here: http://forum.xda-developers.com/showthread.php?t=2231249
Download Motorola Stock Firmwares:
Stock Jellybean for AT&T: http://sbfdownload.droid-developers...MB886_NII_TA-2-16-release-keys-NII-MX.xml.zip
Stock Jellybean for Bell Canada: http://sbfdownload.droid-developers...FFW-11-4-release-keys-BellMobility-CA.xml.zip
Open up your zip file and replace the .xml with the new XML you will download from this link: https://www.box.com/s/num1eshkf0c2or2h4160 You really can't forget to do this!
Launch RSD, connect device to PC, make sure RSD recognizes it. Navigate to your firmware file, select it, and press the start button. Sit back, relax, and let it do its work. It will take around 5-10 minutes. Do not unplug the cable, and do not attempt if you are in a situation in which you think you may lose power (especially if running from a desktop PC).
If RSD Lite won't work, then this thread will show you how to manually flash your stock firmware: http://forum.xda-developers.com/showpost.php?p=40929335
Basically, you repeat all the instructions I just gave you and then manually input some lines in Command Prompt.
Help! My Motorola RAZR I XT890 cannot be "unbricked" and I tried several methods...
Hello!
I unlocked the bootloader successfully, then I tried to root my phone using The Razr guy method and I used the "RAZRi_Root_Windows" file, while rooting my phone went to the "warning bootloader unlocked" screen and it just loops forever from that screen, the bat file, showed that it successfully rooted my phone. I tried to fix it using rsd lite, but it never detects my phone, so I searched for a way to make my pc able to detect it, so I found I could use Intel xFSTK, installed it but still nothing it doesn't appear as shown in the tutorial, I even downloaded the dll file that it needed to run, but after running the xFSTK DLDR or something like that, the application is completely empty, and I saw it should show some tools to download something. Also tried using Linux Zorin, but it only says that my XT890 cannot be accessed and shows an usb error code.
I am able to enter the fastboot screen, the one you get by pressing POWER and VOLUME DOWN, also it charges my batter completely normal. Also my pc is able to show that the XT890 is connected, but only before installing the drivers and it shows the CD installer for the Motorola Device Manager and some other files (all this while looping), and if I enter the fastboot flash mode, it appears as "fastboot smi S", with a yellow triangle and an exclamation sign while in Windows device manager. It has Jelly Bean update from telcel (mexico), and I already have the xml.zip file to reinstall it.
I use windows 8.1 , and as mentioned Linux Zorin on my PC.
Could some help me with it...if you now how to fix it please list every single step on how to do it T_T, THANKS IN ADVANCE!!!!
It looks like the root method changed something bad in your system partition and that's why it won't boot up. First thing to do is installing the correct Motorola drivers. When in fastboot the device should be normally listed and could be acceded by fastboot. If fastboot is working well, use rsd lite to recover it or flash the system partition manually.
If everything is working well, consider installing a custom recovery and flashing a SuperSU zip for root access.
Hazou said:
It looks like the root method changed something bad in your system partition and that's why it won't boot up. First thing to do is installing the correct Motorola drivers. When in fastboot the device should be normally listed and could be acceded by fastboot. If fastboot is working well, use rsd lite to recover it or flash the system partition manually.
If everything is working well, consider installing a custom recovery and flashing a SuperSU zip for root access.
Click to expand...
Click to collapse
Thanks for answering!!
I've checked on some websites that if the phone is not detected by RSD Lite it maybe due to a bug in the phone's driver that happens only on windows 8/8.1, so I will try to do the same thing on windows 7 and see what happens...
Hope it works...T_T
weird_user said:
Thanks for answering!!
I've checked on some websites that if the phone is not detected by RSD Lite it maybe due to a bug in the phone's driver that happens only on windows 8/8.1, so I will try to do the same thing on windows 7 and see what happens...
Hope it works...T_T
Click to expand...
Click to collapse
That could be it.
I just noticed u have unlocked your bootloader. That means u have used fastboot earlier to get the unlock code into the device. So the drivers should work perfectly if u are in the good device modes. Try to flash the system_signed image manually though fastboot and see what happens ("fastboot flash system <path-to-system_signed-image>", u may need mFastboot for that(is inside the rsd-lite package))
Just for the record if u didn't know:
Adb: works only in selected recovery's and normal boot(sometimes in charging mode as well)
Fastboot: works only in AP fastboot mode (power+vol-down, black screen with white/blue text (rsd-lite needs this mode))
XFSTK: works only in medfield flash modues, something u don't need to be with that kind of error
Thanks again!!!
Hazou said:
That could be it.
I just noticed u have unlocked your bootloader. That means u have used fastboot earlier to get the unlock code into the device. So the drivers should work perfectly if u are in the good device modes. Try to flash the system_signed image manually though fastboot and see what happens ("fastboot flash system <path-to-system_signed-image>", u may need mFastboot for that(is inside the rsd-lite package))
Just for the record if u didn't know:
Adb: works only in selected recovery's and normal boot(sometimes in charging mode as well)
Fastboot: works only in AP fastboot mode (power+vol-down, black screen with white/blue text (rsd-lite needs this mode))
XFSTK: works only in medfield flash modues, something u don't need to be with that kind of error
Click to expand...
Click to collapse
Hazou said:
That could be it.
I just noticed u have unlocked your bootloader. That means u have used fastboot earlier to get the unlock code into the device. So the drivers should work perfectly if u are in the good device modes. Try to flash the system_signed image manually though fastboot and see what happens ("fastboot flash system <path-to-system_signed-image>", u may need mFastboot for that(is inside the rsd-lite package))
Just for the record if u didn't know:
Adb: works only in selected recovery's and normal boot(sometimes in charging mode as well)
Fastboot: works only in AP fastboot mode (power+vol-down, black screen with white/blue text (rsd-lite needs this mode))
XFSTK: works only in medfield flash modues, something u don't need to be with that kind of error
Click to expand...
Click to collapse
I am able to enter RECOVERY MODE NOW (I installed CWM, before this I was only able to see the android lying on the floor ans saty dead right there, I was supposed to press Volume + and - and the camera button at the same time, but nothing happened), it seems to be easier to unbrick it this way, but now the problem is that after I follow the steps to reinstall the original ROM, it aborts installation. I read this may be caused due to a file on the zip file, I looked for it, but nor the Folder META-INF, whic is supposed to contain a "update-script" file, nor that file is anywhere in the ROM folder...
I've even tried cyanogenmod (after first trying Telcel original ROM and then the retail GB ROM) cuz it actually contains the folder previously mentioned and the file is in a different path, but it is there, I modified it, but got a "Can't open tmd/update.zip (bad) Installation aborted" error...I don't know what else to do T_T...
Note: I also used sideload and CWM to install it, but the same thing happens. Also checked some other post about this issue, but none has helped me...
What zip file are u installing?
If u want to go back to stock, just use a RSD lite package for 4.1.2 or install TWRP and restore a TWRP backup to go to 4.4.2. There is no official RSD lite package for 4.4.2 and the update.zip doesn't work if your system doesn't boot already.
Hazou said:
What zip file are u installing?
If u want to go back to stock, just use a RSD lite package for 4.1.2 or install TWRP and restore a TWRP backup to go to 4.4.2. There is no official RSD lite package for 4.4.2 and the update.zip doesn't work if your system doesn't boot already.
Click to expand...
Click to collapse
It's done! Thanks!
I actually used another computer with windows 10, also I used RSD Lite and it worked just fine, now I have the stock ROM from Telcel and it it is working almost normal. The only abnormality I've seen is that my phone turns itself off when battery is at 20%, I searched info about that problem and it says I may re calibrate the battery, so it may work fine again, but now I need to root again to be able to do that T_T, hope it works this time...
THANKS! again!
My Lenovo K3 note bricked and now it boots up to spash logo and says dl image error or something. Downloaded the stock rom and tried the spflash tool but it doesnt seems to work. Please help.
e
Download the rom and tool from here- https://www.youtube.com/watch?v=mzN1q0h_YKM&ab_channel=Techjunkie
Hey,
I just uploaded BAD stuff from a BAD folder ...
preloader
ik
logo
secro
system
userdata
No life whatsoever. Tried as I realized after flash is done that I did a big fail to go into recovery (vol + & - & power) but nothing.
Even SPFlashtool is not seeing the phone nor adb.
Please help me unbricking this brand new phone.
/I wanted to make it full Hungarian language.../
I did the same. I tried to install another rom the tool and flash my phone died.
I did the firmware backup and now I am unable to restore the file Scatter.bin by Droid Tools.
I must have firmware.bat file but it was excluded.
someone could help me with this file. if there is a site to download and there is no way to reverse this? Please help me solve. Thank you
Do this
First Sorry for my Bad English
Try to do these steps:
Install all the drivers (including lephone and others)
Open Device Manager on Windows PC
Now plug in your SWITCHED OFF
And notice the hardaware changes
If you find a hardware named "MTK 675XXX Preloader" or something like that, then your mobile can be easily unbricked
if you notice a small triangle under it then the preloader drivers might not be installed
just click on it (be fast because it will only stay for a 10 seconds or less)
and click "Update Driver"
Now, Try to flash using SPF tools
If the above method dosent work then try to boot into bootloader. if not able, then YES, YOU HAVE HARD BRICKED YOUR PHONE