Chromecast Unable to Connect to Network - Google Chromecast

Hey all. New poster long time lurker. I just wanna thank everyone in advance for all the help I've gotten over the years.
Anyway. I own a chromecast and am attempting to connect it to my home wifi network. I'm using a mi424wr-gen3i router with the latest firmware. I disabled IGMP and UPNP is enabled. I turned on IPv6 like some other posters mentioned. My phone (Bionic) gets to the set up page, sees the chromecast but fails at one of two points. Either it says it cannot communicate with the device or it gets to the point of connecting the chromecast to the network and fails. My network is using a WPA2 security key. As far as I can tell my router is not a dual band and only transmits at 2.4ghz. The chrome support mentions something about Access Point/ Client Isolation, but I have no idea what that is or how to configure it. I called both Verizon and Google. Google said check upnp and 2.4 ghz. Verizon said its not their problem.
I was following this thread which seemed to be point on, on my issue. However where other people seemed to make it work, mine still fails.
http://forum.xda-developers.com/showthread.php?p=44018888

drstrangelove5 said:
Hey all. New poster long time lurker. I just wanna thank everyone in advance for all the help I've gotten over the years.
Anyway. I own a chromecast and am attempting to connect it to my home wifi network. I'm using a mi424wr-gen3i router with the latest firmware. I disabled IGMP and UPNP is enabled. I turned on IPv6 like some other posters mentioned. My phone (Bionic) gets to the set up page, sees the chromecast but fails at one of two points. Either it says it cannot communicate with the device or it gets to the point of connecting the chromecast to the network and fails. My network is using a WPA2 security key. As far as I can tell my router is not a dual band and only transmits at 2.4ghz. The chrome support mentions something about Access Point/ Client Isolation, but I have no idea what that is or how to configure it. I called both Verizon and Google. Google said check upnp and 2.4 ghz. Verizon said its not their problem.
I was following this thread which seemed to be point on, on my issue. However where other people seemed to make it work, mine still fails.
http://forum.xda-developers.com/showthread.php?p=44018888
Click to expand...
Click to collapse
Have you tried rebooting your router, disable MAC address filtering if it is enabled, and/or reset the router's settings back to default

supernova_00 said:
Have you tried rebooting your router, disable MAC address filtering if it is enabled, and/or reset the router's settings back to default
Click to expand...
Click to collapse
Yeah. I rebooted to the factory reset. Unfortunately its a verizon issued modem/router combo and its to their specs. MAC filtering is disabled and its been rebooted.

Get the latest router from Verizon & turn off IGMP. Swapping out the router should be free.
Sent from my SGH-T999 using Tapatalk 4

I was having a similar problem but I realized that Chromecast only needs the network name and it's password to work. After the step were you put in the password and it fails, I should work..Also, if you are getting stuck renaming chromecast, leave it the way it is for now. Before you start over, check to see if you can see chromecast on you network using Fing or a similar program.

drstrangelove5 said:
Hey all. New poster long time lurker. I just wanna thank everyone in advance for all the help I've gotten over the years.
Anyway. I own a chromecast and am attempting to connect it to my home wifi network. I'm using a mi424wr-gen3i router with the latest firmware. I disabled IGMP and UPNP is enabled. I turned on IPv6 like some other posters mentioned. My phone (Bionic) gets to the set up page, sees the chromecast but fails at one of two points. Either it says it cannot communicate with the device or it gets to the point of connecting the chromecast to the network and fails. My network is using a WPA2 security key. As far as I can tell my router is not a dual band and only transmits at 2.4ghz. The chrome support mentions something about Access Point/ Client Isolation, but I have no idea what that is or how to configure it. I called both Verizon and Google. Google said check upnp and 2.4 ghz. Verizon said its not their problem.
I was following this thread which seemed to be point on, on my issue. However where other people seemed to make it work, mine still fails.
http://forum.xda-developers.com/showthread.php?p=44018888
Click to expand...
Click to collapse
I have had same issue and fixed it by doing a MANUAL entry of all wireless connection to your router... type in SSID, pick WPA2, and enter passcode.

Well after several hours of talking with Google and Verizon again. Verizon hung up on me and Google solved the problem. Apparantly my phone (Droid Bionic) is not communicating with the device properly. Off all things i was able to set it up with my buddies IPAD. Ironic right? Now I just need to figure out what the heck is wrong with my phone. I read somewhere that the razrs were having problems. The Bionic and Razr are one in the same so i guess ill head that way. Anyway thanks guys.

drstrangelove5 said:
Well after several hours of talking with Google and Verizon again. Verizon hung up on me and Google solved the problem. Apparantly my phone (Droid Bionic) is not communicating with the device properly. Off all things i was able to set it up with my buddies IPAD. Ironic right? Now I just need to figure out what the heck is wrong with my phone. I read somewhere that the razrs were having problems. The Bionic and Razr are one in the same so i guess ill head that way. Anyway thanks guys.
Click to expand...
Click to collapse
It's always a good idea to try different devices when possible. Adding the Google Cast extension on Chrome for the PC may be the easiest to work with since you're using a full keyboard.

I had to manuilly allow my chromecasts Mac address... Then it worked no problem.
Sent from my SCH-I535 using Tapatalk 2

drstrangelove5 said:
Well after several hours of talking with Google and Verizon again. Verizon hung up on me and Google solved the problem. Apparantly my phone (Droid Bionic) is not communicating with the device properly. Off all things i was able to set it up with my buddies IPAD. Ironic right? Now I just need to figure out what the heck is wrong with my phone. I read somewhere that the razrs were having problems. The Bionic and Razr are one in the same so i guess ill head that way. Anyway thanks guys.
Click to expand...
Click to collapse
My wife's razr had the same issue. You could have also used your PC to set it up.
Here is the thread on the Razr / Bionic issue: groups.google.com/d/msgid/chromebook-central/1280fb6a-d063-4d77-993d-dbec4fc6cdb6%40googlegroups.com (sorry, you have to copy/paste it, I have less than 10 posts so I can't post links yet).
Play Music and Play Movies/TV probably won't work for you either.

Just hit Try Again and it will work. It fails the first time, and hitting Try Again did the trick.
Not sure if it was luck or what not.

Related

WiFi DoA on my Tilt/Kaiser?

Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Wow. Am I the only one on here who's having this problem?? Lucky me, I guess... :S
Anyway, I just tried connecting to a public and open wifi network here in SF, but my Kaiser still wouldn't connect. Guess that confirms it: my WiFi adapter is defective.
Anyone know if I can get it replaced in a different store from where I purchased it, and what I need to take (hope it's just the phone)?
d0ubl3_d1zzl3 said:
Wow. Am I the only one on here who's having this problem?? Lucky me, I guess... :S
Anyway, I just tried connecting to a public and open wifi network here in SF, but my Kaiser still wouldn't connect. Guess that confirms it: my WiFi adapter is defective.
Anyone know if I can get it replaced in a different store from where I purchased it, and what I need to take (hope it's just the phone)?
Click to expand...
Click to collapse
just tried my wifi on the tilt ... works fine out of the box (to my home secured wireless network)
d0ubl3_d1zzl3 said:
Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Click to expand...
Click to collapse
This is what I did. Start->settings->connections tab->WiFI. Now you should see your routers name there with the signal bar next to it. Tap AND Hold the name, then go to settings or edit(I forget), then click NEXT, uncheck the box that says "the key is automatically provided"(thats for open access routers/networks that dont require codes). Then type in your code & make sure you specify what key # it is. click next and youre done. You should be able to connect.
silly question here. is your router broadcasting 802.11b or g? the wifi won't connect to anything else.
You might also check your AP to see if it's not broadcasting its SSID to the world (a common security setting). I couldn't connect until I enabled broadcast on my AP, set the network up, and then went back and disabled SSID broadcast.
Why in the hell this is a problem in the first place is beyond me, but this is the third smartphone/PDA with wireless that I've had to do that for. And every time, once the device found the network once, it never had a problem finding it again.
Believe me. I tried everything in the WiFi settings page. I edited the settings, removed them and added them again, and like I said before I even went and changed my security settings on my router (which to answer your question, zeta, it broadcasts in: n, g, and b. Same router worked with my Apache/XV6700).
Anyway, I stopped by the store where I bought it today and they told me that as far as he can tell, that does qualify for a replacement. The problem is they don't have any in stock to replace it with, and he has no idea when they'll be getting more in. They only received 2 on launch day, and I bought one of those. He did mention that I can get it replaced at any store, however, but they all might be in the same boat.
Guess I'll try another store tomorrow, but if not I guess I'll have to go through AT&T's tech support (don't like the sound of that) and get it replaced through them. So I guess this means I might have a few days to mess around with the phone and even try some risky thangs.
So if any of you developers and hackers, er, I mean tweakers need some1 to test something, I can be that guinea pig (for a while at least)... Just give me a shout.
To troubleshoot your wireless connection always try ruling out as many other factors as possible. So put your router to NO security (temporarily ofcourse) and have it broadcast 802.11g. Also make sure you add the mac address of your device to the list in your router, if it uses mac address filtering. Try connecting to it with a laptop and see if that goes fine. Work systematically...
PerfAlbion said:
You might also check your AP to see if it's not broadcasting its SSID to the world (a common security setting). I couldn't connect until I enabled broadcast on my AP, set the network up, and then went back and disabled SSID broadcast.
Why in the hell this is a problem in the first place is beyond me, but this is the third smartphone/PDA with wireless that I've had to do that for. And every time, once the device found the network once, it never had a problem finding it again.
Click to expand...
Click to collapse
I have a similar Problem, your solution works partly for me:
As soon as I enable the AP to broadcast it's ID, Kaiser connects.
But as soon as the ID is hidden, it does not connect.
Weird.
Is it a security problem if the ID is broadcasted, provided I use WPA2-PSK/AES?
Thanks
V
No. Hiding the SSID really only protects you from folks that are wandering around without any tools. Open up a more fully featured scanner, and it'll pull the SSID out of the air. The encryption is much, much more important.
And I also wouldn't bother with MAC filtering. Changing the MAC address is usually a software setting, so it's not all that much additional security. WPA/WPA2 are much better solutions.
Yeah, the hidden SSID is not an issue with me, since I don't mind broadcasting it at home. Not too paranoid about it. If someone *really* wanted to sniff and break into my network, they could. Don't do much important and highly confidential stuff at home anyway.
Plus, like Perf mentioned, there's software out there, even for PocketPCs, that will find so-called "hidden" SSIDs. Thanks for your suggestions, anyway.
d0ubl3_d1zzl3 said:
Yeah, the hidden SSID is not an issue with me, since I don't mind broadcasting it at home. Not too paranoid about it. If someone *really* wanted to sniff and break into my network, they could. Don't do much important and highly confidential stuff at home anyway.
Plus, like Perf mentioned, there's software out there, even for PocketPCs, that will find so-called "hidden" SSIDs. Thanks for your suggestions, anyway.
Click to expand...
Click to collapse
i had no issue connecting to my wrt54g running DD-WRT v23 SP2 with my SSID hidden with WEP enabled. when setting up a new connection, i just entered the name of the connection and then the WEP hex, and it connected flawlessly. Have fun hacking your phone until you can swap?
Mine is not working either. I exchanged the phone and found out that I was the 3rd person with the same problem.
BiPolarXpress said:
Mine is not working either. I exchanged the phone and found out that I was the 3rd person with the same problem.
Click to expand...
Click to collapse
Glad to hear, I'm not the only one.
I exchanged my phone this morning, and I just tried connecting to my wireless network and guess what??
I'm getting the SAME RESULTS.
Now, before anyone goes and tells me that my router is the problem or that it's user error, then tell me: why does my laptop, PS3 and my Wii connect just fine?? I even changed the SSID and WPA key last night and they all connected w/o a problem as well. All except my freaking Tilt.
Can be it a coincidence that I got 2 bad phones? I don't know if I should call the store and tell them to hold up on sending the other phone to HTC.
Which reminds me, I probably should try calling HTC today, but I doubt they'll be much help...
I don't think you're nuts, and I doubt you got two bad phones. But if you want to double-check, take the phone to your local Starbucks or other shop with WiFi and see if it can detect that AP.
But at this point, I'd be inclined to look for a firmware upgrade for your AP. I could be that it's not supporting long or short preambles right (a problem for some devices in the past), doesn't like seeing more than XXX different devices, or just doesn't like your phone much.
Either way, I'm smelling an issue with your AP. I had a US Robotics AP/Router that drove me nuts because it would spontaneously reboot after a random period any time an IPSec VPN was present.
try setting the power mode on best performance. when i do that i stay connected to wifi.
I took both my old I730 and my tilt to the coffee shop before I returned my first tilt. I was able to connect my I730 at the coffee shop and home, but couldn't connect the tilt at either place. I also tried some open AP's in my neighborhood that I have been able to connect to in the past with the same results. Picky phone or bad wifi radios maybe.
Jesus... like the bloke said:
1) Turn off wpa and see if it will connect (it will unless you have set your N router to only use "n") If it won't then send it back.
2) If it does... then turn on WEP 128bit on your router... and use that instead.
WM devices have always had problems with WPA...
Hi all.
I have tried my HTC TyTN II with one Wifi LinkSys WAG54GS Router using WPA and not hidding the SSID and works fine, no problem at all.
Test with one AP from DLink at the office, using hidden SSID and WEP 64 and 128 Bits and no problem at all, works as fine as my LinkSys.
I'm going to try hidde the SSID at home with WPA and WPA2 and post the results later to know if there is a common issue with Kaiser or some freaky coincidence.
Regards.
d0ubl3_d1zzl3 said:
Hello Everyone,
I'm looking for either a confirmation that my my WLAN is bad, or suggestions on other things I should try before taking it back in for replacement.
Searching and browsing through the forums I didn't see anyone mention any of the problems I'm having so I'm assuming I'm the only one (or one of very few) that bought a Kaiser with a defective Wifi radio.
Here's the symptoms:
I tried connecting to my wireless connection at home maybe a day or two after I bought my Tilt (last Friday). My home connection is draft 802.11n with WPA2-PSK security.
So I enable the WLAN and it detects my Wifi network and it asks for the key. I input it and then it tries to connect, but... it never does. I tried it a few times consecutively and it still didn't work (I get the animating arrows and the 'halo' around the beacon, but then it goes away, and it just keeps doing that). Now, I've seen this before with on my XV6700 with a beta ROM of WM6, but I know well HTC and AT&T wouldn't release something with broken WPA/2 support. At least HTC, I thought...
So I unlocked my Tilt and loaded the factory Kaiser ROM I downloaded from here, and well, WPA2 didn't work on it either. Weird, I thought, so I searched forums and no one mentioned any of this. So I changed my security settings on my network to WPA-PSK (from WPA2) and that made no difference at all... I don't want to bore y'all with everything else I tried, but to sum it up, I then tried a WPA fix I found on PPCGeeks, but that just ended up making my WLAN staying disabled, so I unintalled that and I decided I would try it with a WEP or Open wireless network.
Well, this morning I did just that and even when I try to connect to a wireless connection with WEP, I get the same behavior when I tried this at home with WPA. I've triple checked the WEP key, and I know it's right.
I haven't tried it on an Open network yet, but I'm assuming I'm going to get the same results. I'll have to find a wireless router no one's connected to so that I can try this out, but it might take me a while. Should I even waste anymore time on this? Anyone else here having (or had) the same problem?
I might start loading the AT&T ROM on this soon so I can take it back, but if any of you have any suggestions, I'm all ears.
Click to expand...
Click to collapse
I found that I couldn't get my Kaiser to connect to my WPA encrypted LAN - open access and WEP (64 and 128 bit) work fine.
Not sure what the problem is - maybe some incompatibility between the Kaiser and my Netgear router. I've downgraded the security to 128bit WEP for the time being but I'm hoping that there's a fix soon.

Verizon FiOS and Wi-Fi

Hey all. I saw a thread where an issue was briefly mentioned before but saw not resolution. I just had FiOS installed at my house last week and ever since then I cannot get to the internet when connected to Wi-Fi.
Just so there is not any confusion, I am able to connect to wi-fi and get an IP address. I am also able to access the verizon router's web page from my phone but cannot get out to the internet. It works fine on 3G and Edge.
The problem is seen on both my G1 (running Super D 1.5) and my wife's phone (Running CM 4.2.4).
Anyone else seen this problem and know a solution?
Sounds like a router problem. Get a different one, or turn all the security off on the Verizon and restore to default settings.
evilkorn said:
Sounds like a router problem. Get a different one, or turn all the security off on the Verizon and restore to default settings.
Click to expand...
Click to collapse
I already turned off all the wi-fi security and tried, still a no go. Verizon FiOS uses a modem/router combo and you have to use it. Prior to last week I had a Comcast using a Motorola Surfboard Cable Modem and a D-Link Wireless router with no issue.
I have no doubts this is a router issue I just don't know what it could be as all 3 of my wireless computers are able to access the internet without any issues. The only devices that are having problems are the wife and my G1's.
I will try to do a factory reset today but am afraid this may affect the FiOS home media server and other Set Top Box I have.
I was just hoping someone had a solution to this as someone else mentioned the issue on this thread: http://forum.xda-developers.com/archive/index.php/t-444245.html
Best bet is to take it up with verizon, I'm sure there are other people that have the problem.
It's good to know they force you into using their hardware, I wouldn't want to go without a proper router, so it could be a deal breaker for some.
evilkorn said:
Best bet is to take it up with verizon, I'm sure there are other people that have the problem.
It's good to know they force you into using their hardware, I wouldn't want to go without a proper router, so it could be a deal breaker for some.
Click to expand...
Click to collapse
yeah, basically what I had done was turned off the wi-fi on the verizon router and hooked my D-link wireless N router up so the Verizon was basically just acting as a modem. I took my d-link out of the equation to troubleshoot and determined that it is definitely something with the Verizon router, I just don't know what. The interface on the Verizon router is crap too.
I'm going to reset the router today and see if that resolves the problem. Other than this issue I have been totally happy with their service. The FiOS Cable is nice and the broadband is way faster than what I was getting with Comcast.
This is solved. It turned out to be a port forwarding issue.

I can NOT get it to work with Verizon FIOS Actiontec router

I plugged in the Chromecast and put in all the information and waited while it tried to connect to my Actiontec router. (Verizon FIOS) I waited, and waited and waited. After about 10 minutes it goes back to the beginning. The help button says I need to turn off the Access Point Isolation on my router. Unfortunately there's no such setting. I'm not happy because I have 3 more of these coming tomorrow and if I can't connect to my network I'm shot. Panic starts to set in.
Luckily, I have a cheap $30 Fry's wifi router on my network. I switched the Chromecast to the Fry's router and, bam, it connected immediately.
So, if your cable company's router doesn't work, just go out and buy a cheapo wifi router and you'll be fine.
The joy that is reading Verizon FiOS/Actiontec entrails
Deep voodoo Actiontec solution: You need to disable the IGMP Proxy.
The exact location of this checkbox changes between Actiontec revs but a good start is "Advanced/Routing/Routing Protocols/Internet Group Management Protocol (IGMP)."
Once this is off network devices typically can discover & connect to eachother.
Another strategy is, on the latest revs, enabling IPv6 (no, after years of promises Verizon still hasn't rolled IPv6 out yet, but at least the latest routers might be ready.) Anyhow, this is often reported to resolve local connectivity issues.
Just for reference, I have the newest Fios Actiontec router, and had no problems. Just so everyone with that router doesn't think they'll necessarily need to do this.
Sent from my SGH-T889 using Tapatalk 2
Evo4gLI said:
Just for reference, I have the newest Fios Actiontec router, and had no problems. Just so everyone with that router doesn't think they'll necessarily need to do this.
Sent from my SGH-T889 using Tapatalk 2
Click to expand...
Click to collapse
Good point. Mine's about 6 years old, maybe I should get them to replace it.
I had the same problem. Turned off NAT, connected, then turned NAT on
Guess this is reason #153 why I'm glad I have a Linksys router piggy-backed off of the crappy FIOS unit for the majority of my networking needs
A tip if upgrading to a newer Actiontec router: The settings backup files are *not* compatible between versions.
I upgraded to the latest router version six months ago; I'd done a lot of customizing (assigning addresses, ports, etc) and assumed it'd be an easy switch. I ended up having to temporarily return my newer router to get back my old, screenshot many pages of settings, return the old for new, then re-enter settings. A hassle, but it does run better now.
Assuming the local depot/storefront has 'em in stock it's a few minutes to swap out for a newer or newest revision.
Coincidentally I had a visit a week later to replace a burnt-out-again ONT & the tech reported he'd changed things around a bit in it for even better service. I've no idea what that involved but if it's been a long time you might want to look into a service call.
Sent from my SGH-T999 using Tapatalk 4 Beta
Some Help
I also picked up a Chromecast yesterday and am on Verizon Fios with the new Actiontec MI424WR router. I cannot get my Chromecast to connect. Sometimes I see it on the network, but it will not connect. Verizon, Actiontec, and so far Google have not been able to help me. I tried the tricks in this posting, but no luck.
I have a Buffalo Air Station wireless router, but have not had success operating this in conjunction with the Fios service (I have tried to bridge it, and run it just off ActionTec). Can someone help? I am okay at digging into this stuff, but you guys know so much more than me!
HELP!
success
The instructions below worked for me. Found it in an Apple Forum out of all places.
log in to your router(192.168.1.1), go to Wireless Settings then Advanced Security Settings. At the bottom of the screen, click "Other Advanced Wireless Options". On the next screen change Network from "Network (Home/Office)" to "Broadband". Click Apply
Just curious but it could be that you have multicasting disabled on the router.
It could also be that the router does not support multicasting in general, but this is a feature that allows devices to discover each other on a private network.
spm139 said:
I also picked up a Chromecast yesterday and am on Verizon Fios with the new Actiontec MI424WR router. I cannot get my Chromecast to connect. Sometimes I see it on the network, but it will not connect. Verizon, Actiontec, and so far Google have not been able to help me. I tried the tricks in this posting, but no luck.
I have a Buffalo Air Station wireless router, but have not had success operating this in conjunction with the Fios service (I have tried to bridge it, and run it just off ActionTec). Can someone help? I am okay at digging into this stuff, but you guys know so much more than me!
HELP!
Click to expand...
Click to collapse
I am having the same issue with DIR 655 router. Tried all the suggestion in this thread. But still no luck. Anyone having similar problem with DIR 655?
I'm having a similar problem. I've got a Linksys router that is happily supplying WiFi to my laptop, mobile phone, Kindle Fire, and XBox, but I can't get Chromecast to work properly. I get partially into the setup and then get the following message -- "Chromecast connected to [Name of Network], but can't connect to the internet." I've fiddled with countless settings to no avail. AP/Isolation mode is disabled, I've only got 2.4 GHz bands, the router is 20 ft away, etc. All the suggestions the Google Help guy gave me have had zero effect, so I thought I'd post here to see if anyone else ran into this error message and had a solution.
mowgle said:
I am having the same issue with DIR 655 router. Tried all the suggestion in this thread. But still no luck. Anyone having similar problem with DIR 655?
Click to expand...
Click to collapse
OK! finally found the issue. If your wifi password is too long(auto generated for WPA2) then chromecast cannot handle it. Reducing the length of router password fixed it. I reduced it to ~20 characters. Have not tested the pw length limit of cast.
mowgle said:
OK! finally found the issue. If your wifi password is too long(auto generated for WPA2) then chromecast cannot handle it. Reducing the length of router password fixed it. I reduced it to ~20 characters. Have not tested the pw length limit of cast.
Click to expand...
Click to collapse
My password is only 9 characters, and I have tried everything else suggested here. Anyone else have any ideas on how to get it to work?
I'm also having a similar issue with my DIR-601. I am able to detect my Chromecast but after the screen that asks for the WiFi info /renaming the Chromecast, I get an error stating that we were unable to find Chromecast on your network. I have checked that UPnP and have Enable IPv4 Multicast Streams selected (tried both ways.) I don't have any special firewall rules or anything like that. My pass is only 8 characters.
Wish Google had better support for this, all they have is a little questionnaire on their support page.If anyone finds a solution, please share. Thanks
Out of curiosity where is the enable multicast option at? I didn't see one.
Sent from my HTC One X using Tapatalk 2
axdela said:
log in to your router(192.168.1.1), go to Wireless Settings then Advanced Security Settings. At the bottom of the screen, click "Other Advanced Wireless Options". On the next screen change Network from "Network (Home/Office)" to "Broadband". Click Apply
Click to expand...
Click to collapse
Thanks! This is the only solution that fixed it for me.
axdela said:
The instructions below worked for me. Found it in an Apple Forum out of all places.
log in to your router(192.168.1.1), go to Wireless Settings then Advanced Security Settings. At the bottom of the screen, click "Other Advanced Wireless Options". On the next screen change Network from "Network (Home/Office)" to "Broadband". Click Apply
Click to expand...
Click to collapse
Worked for me as well. Thank you! :good:
None of the suggestions in this thread worked for me. I have the Actiontec Gen 3, rev I router (MI424WR-GEN3I), with firmware v. 40.20.7.
Apparently, the UPnP page is hidden, but can be accessed after logging in to the router using: 192.168.1.1/index.cgi?active_page=900. Changing the settings on this page didn't work either.
After a quick Google, I found an IGMP hidden page at 192.168.1.1/index.cgi?active_page=6059. I looked at these settings yet.
Calling Verizon's Expert Care, I was told that they don't support UPnP, since they only provide access to the Internet.
Fix found ... at least for me
AJL-Hates-Verizon said:
None of the suggestions in this thread worked for me. I have the Actiontec Gen 3, rev I router (MI424WR-GEN3I), with firmware v. 40.20.7.
Apparently, the UPnP page is hidden, but can be accessed after logging in to the router using: 192.168.1.1/index.cgi?active_page=900. Changing the settings on this page didn't work either.
After a quick Google, I found an IGMP hidden page at 192.168.1.1/index.cgi?active_page=6059. I looked at these settings yet.
Calling Verizon's Expert Care, I was told that they don't support UPnP, since they only provide access to the Internet.
Click to expand...
Click to collapse
I had the same issues as everyone else at both my office and my house. At home, I changed the IGMP settings, the UPnP settings, the security settings, etc. I finally figured out a way to make it work by simply trying to complete the setup from my laptop instead of my Droid 4. It worked on the first try at my house, and now all of my phones, tablets and computers can cast to the big tv. I immediately brought my laptop to the office and changed the IGMP setting -- and it immediately worked after that.
So maybe a solution is to try setting it up from your computer instead of your phone/tablet? It worked for me twice that way!

Chromecast will not connect to my TELUS ROUTER

Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:
2237 9525694
mydrl said:
Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:
Click to expand...
Click to collapse
How?
try changing the wifi channel the router uses
mydrl said:
Chromecast wont connect to my telus router (Actiontec V1000H). I can't see any option to enable/disable AP Isolation. Is there any solution for this?
fixed:laugh:
Click to expand...
Click to collapse
How did you fix this?
MadBob said:
try changing the wifi channel the router uses
Click to expand...
Click to collapse
Good advice.
Remember that the WiFi bands (channels) are not exactly the same between countries. So if you're in a non-US country and your router happens to choose a channel that is not available in the US, Chromecast may not detect your wireless AP.
But Telus is Canadian, and Canada has the same WiFi channels as the U.S. (Canada and the U.S. necessarily share identical radio spectrum allocation).
DJames1 said:
But Telus is Canadian, and Canada has the same WiFi channels as the U.S. (Canada and the U.S. necessarily share identical radio spectrum allocation).
Click to expand...
Click to collapse
Didn't know that. Thanks! Still applies to other countries though. I think Channel 13 is one of the channels that applies to Europe but not US. I should put it in the FAQ...
EDIT: Seems there's far less exclusion than I thought... but added a note in the FAQ just in case.
http://en.wikipedia.org/wiki/List_of_WLAN_channels
So I can get through the setup phase up until the Chromecast tries to connect to my wifi network. I get a message saying it couldn't connect, and when I click the link in the message it brings me to a page that mentions AP filtering, UPNP enabling and .NET 3.5. I checked and UPNP is enabled, and I can't find an option for AP filtering (I have the Actiontech V1000h). I am using a Macbook pro.
Kipp34 said:
So I can get through the setup phase up until the Chromecast tries to connect to my wifi network. I get a message saying it couldn't connect, and when I click the link in the message it brings me to a page that mentions AP filtering, UPNP enabling and .NET 3.5. I checked and UPNP is enabled, and I can't find an option for AP filtering (I have the Actiontech V1000h). I am using a Macbook pro.
Click to expand...
Click to collapse
In some cases you have to go through a couple of times. I just reset my Chromecast to test a few things and had to go through the setup twice before it connected to my WiFi.
Chromecast in Canada, on Telus
A friend lent me his chromecast. He uses an iphone and Shaw cable. I use a Nexus 4, and have Telus as my internet provider.
It was a bear trying to get chromecast to work. Tried 5 separate days. Got it to work and i could watch netflix/youtube on it about 3 times and played with it for a couple of hours each. That's the success.
The fail is that I had to trouble shoot more then 4+ hours to get it to work those 3 times. Reboot the chromecast. Reboot the router. Reboot my Nexus 4. Try my wife's Nexus 4. Try the Nexus 7 tablet. It was a horrible experience. I got the AP recommendation like the earlier post in this thread. I tried that. Tried calling telus and signed into my router to check that those settings were correct. As far as I understand it's a gateway 11n wireless router.
So my conclusion is change my internet provider to Shaw unless someone has a smart solution to this problem. The router says it's a 50ghz signal? So it isn't the 2.4vs 5.0 ghz signal problem that I've googled and read about.
Please provide some brains to my situation. I've used all of mine up.
bhiga said:
In some cases you have to go through a couple of times. I just reset my Chromecast to test a few things and had to go through the setup twice before it connected to my WiFi.
Click to expand...
Click to collapse
Still not fixed.
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.
johnson2423 said:
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.
Click to expand...
Click to collapse
TVs are great at blocking/scrambling radio signals.
Use the included HDMI extender. If that doesn't help (enough), get an HDMI extension and move Chromecast away from the TV. One of mine is on a 10-foot HDMI extension. The other is connected upstream of a another device that connects to my TV, so both of my Chromecasts are at least a foot away from its associated TV.
johnson2423 said:
So I took the plunge and bought one. Maybe it'd be different than my friends. Looks like this is a me problem. The chromecast still doesn't work. I thought it might be the tv that it's plugged into? Maybe shielding the chromecast from the wifi? I don't know. Will trouble shoot with a different tv or a long hdmi cable that will get the chromecast out from behind the tv. Maybe that'll help.
Click to expand...
Click to collapse
It could be a few things not related to the router directly but related in how the Router connects to your ISP.
So a couple of questions...
What kind of service is your ISP? (DSL, CABLE, OTHER)
What Public IP does your router report? (Usually found on the status page that shows connection data) If it starts off 192.168 then your Modem is doing a double nat translation and you need to call your ISP and tell them you want the Modem to be put into gateway mode and just pass a public IP to your router.
Does the CCast actually connect to the Router but not work or will it not connect at all period? If it doesn't connect at all it is possible you need to change the Security method used to WPA or WEP. To test shut off security alltogether and try to connect the CCast. If there is currently NO security try putting WPA on and trying again (but it should work on an open AP)
fixed...
Asphyx said:
It could be a few things not related to the router directly but related in how the Router connects to your ISP.
So a couple of questions...
What kind of service is your ISP? (DSL, CABLE, OTHER)
What Public IP does your router report? (Usually found on the status page that shows connection data) If it starts off 192.168 then your Modem is doing a double nat translation and you need to call your ISP and tell them you want the Modem to be put into gateway mode and just pass a public IP to your router.
Does the CCast actually connect to the Router but not work or will it not connect at all period? If it doesn't connect at all it is possible you need to change the Security method used to WPA or WEP. To test shut off security alltogether and try to connect the CCast. If there is currently NO security try putting WPA on and trying again (but it should work on an open AP)
Click to expand...
Click to collapse
Service is Telus DSL.
Solution: I changed the security settings. It still tries to stop the CCast from talking to my phone once in a while, but I just log into my router and log into the firewall settings. The firewall settings are "high, medium, low, NAT". It started working once I started turning it off of NAT and onto Medium or High.
I don't know why this is the solution, but it is a solution. I suspect that either Telus will fix the prolbem for everyone else or this thread will become popular. Now CCast is coming to Canada. So either Telus fixes it or there'll be a lot of searching leading to this post.
As a reminder, a friend of mine on telus never toughed his firewall settings and never had a problem with using his CCast. Go figure.
johnson2423 said:
Service is Telus DSL.
Solution: I changed the security settings. It still tries to stop the CCast from talking to my phone once in a while, but I just log into my router and log into the firewall settings. The firewall settings are "high, medium, low, NAT". It started working once I started turning it off of NAT and onto Medium or High.
I don't know why this is the solution, but it is a solution. I suspect that either Telus will fix the prolbem for everyone else or this thread will become popular. Now CCast is coming to Canada. So either Telus fixes it or there'll be a lot of searching leading to this post.
As a reminder, a friend of mine on telus never toughed his firewall settings and never had a problem with using his CCast. Go figure.
Click to expand...
Click to collapse
Well if the Telus was set to NAT perhaps Double Nat Translation was the issue.
DO you have another router connected to your modem or is this one of those all in one Hybrids supplied by the ISP?
Asphyx said:
Well if the Telus was set to NAT perhaps Double Nat Translation was the issue.
DO you have another router connected to your modem or is this one of those all in one Hybrids supplied by the ISP?
Click to expand...
Click to collapse
I have a friend that is struggling with this as well. While setting up the WiFi connection between the chromecast and the router (the Actiontec V1000H - which is a modem/router combo if that helps). The chromecast will see the WiFi, but it seems to time out while trying to connect to the router.
I did find a comment on a blog somewhere (sorry, I forget where) that suggests unchecking the "IGMP snooping enabled" option in the router (Advanced Settings>IGMP Setting). Once this was done, the chromecast connected to the WiFi without any issues and we were able to stream it without any issues.
However after going out for dinner we had major issues trying to connect to the WiFi on our phones and his laptop (laptop would try to connect to the WiFi but continually fail). It seems like this is a temporary fix at best.
The only permanent solution I can think of at the moment is to go buy a new router that is listed as having no issues on the chromecast compatibility list... Which kind of defeats the whole purpose of having the chromecast as an economic way to stream content to your big screen.
Buy a better router
I don't see why IGMP should have any affect on being able to login and connect.
I Can see it being a problem with streaming but not connection.
IS this an ISP provided Modem/Router? How many devices are connecting wirelessly?
Check settings for IGMP Proxy, Try changing that setting whatever it is but it should probably be disabled (Still don't think this would affect connection but it's worth checking)
Check if UPnP Is enabled (again not really connection related but it does need to be enabled for CCast)
I personally prefer to use a two device setup with separate Modem (in Bridge Mode) and Router....This way the Modem protects the router from the outside world and even if the Modem goes bad the Network still functions properly.
And I pretty much stay away from anything that isn't a Linksys or Netgear product as far as Routers are concerned.
There are a bunch of Actiontec models that are listed as incompatible with CCast on the google site so it's obvious that something about their firmware is not CCast friendly.
So the the previous poster may actually have made a good suggestion in the long run! LOL
I'm using the telus actiontech router with chromcast with no issues....
its a pretty crappy router though and it seems telus disabled the ability for bridge mode in the latest firmware... has anyone found a solution to this so i can buy a better router?
Sent from my Nexus 7 using Tapatalk
nolook said:
I'm using the telus actiontech router with chromcast with no issues....
its a pretty crappy router though and it seems telus disabled the ability for bridge mode in the latest firmware... has anyone found a solution to this so i can buy a better router?
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
As long as double NAT doesn't cause you problems, you can
Assign the new router's WAN port to an address in the ISP router's LAN range
Set the new router's gateway to the ISP router's LAN address
Connect the two routers LAN port to LAN port
Have all your wired and wireless clients connect to the new router.

Issues with new TWC modem/router

Hi all, while thinking that faster internet would be a good thing, it seems that I have managed to break chromecast compatibility with my network. Previously I had a Netgear router that worked perfectly, but when we got an upgrade to TWC's new "Extreme Internet" they installed a new WiFi router/modem hybrid that I cannot seem to connect to. I get the message that it is connected to the network but not the internet. Ap isolation. Is disabled, but I cannot find the plug and play feature anywhere in the network settings. Has anyone found a work around?
Sent from my SAMSUNG-SGH-I317 using Tapatalk
jmikeb92 said:
Hi all, while thinking that faster internet would be a good thing, it seems that I have managed to break chromecast compatibility with my network. Previously I had a Netgear router that worked perfectly, but when we got an upgrade to TWC's new "Extreme Internet" they installed a new WiFi router/modem hybrid that I cannot seem to connect to. I get the message that it is connected to the network but not the internet. Ap isolation. Is disabled, but I cannot find the plug and play feature anywhere in the network settings. Has anyone found a work around?
Click to expand...
Click to collapse
If you can give us the exact make and model we might be able to help more.
BTW, TWC changed their policy a few years back and now allow approved customer-owned modems which will save you the modem rental. They used to not charge for the modem rental but also not let you use your own. Installed a Motorola SB6141 for my relative and it's been working great with the Netgear WNDR3700 I put there.
No Chromecast yet because I haven't been by to visit...
You could always use your own modem with twc, just that most people did not know that. Like previously mentioned, more details are needed in order to further assist you. Make and model(tg862g, ddw3611, dvw32011b???). More than likely you just need to call and talk with level 3 tech support. I personally used my own router behind the modem because I do a bit more than normal with my router.
jmikeb92 said:
Hi all, while thinking that faster internet would be a good thing, it seems that I have managed to break chromecast compatibility with my network. Previously I had a Netgear router that worked perfectly, but when we got an upgrade to TWC's new "Extreme Internet" they installed a new WiFi router/modem hybrid that I cannot seem to connect to. I get the message that it is connected to the network but not the internet. Ap isolation. Is disabled, but I cannot find the plug and play feature anywhere in the network settings. Has anyone found a work around?
Sent from my SAMSUNG-SGH-I317 using Tapatalk
Click to expand...
Click to collapse
I went through Hell on Christmas Eve with Time Warner....
They have a new Modem/Router they are using....When connected to a personal Router it does a double Nat translation which really doesn't work at all.
Your lucky if you even get Internet access on a Computer with it.
Check your router and see what IP address it has under internet connection. It should not be 192.168.0.x
If it is not an outside IP you need to call support and tell them you need your Router to breach the Modem and have them shut off all ROUTER capability on their Device so that all it does is pass a public IP to whatever is connected to it.
If you get your phone service from Time Warner as well better call on a Cell Phone because they will drop the phone call the second they mess with their Modem/Router and you will suffer through Groundhog day explaining it to the next guy from scratch!
Well guys I solved my own problem in a way. I disabled the wireless broadcast from the TWC Arris router and just connected my old NetGear ( old as in 2 months old) and it seems to work perfectly now. And the installer said, " You won't need to use your old one because this box is like commercial grade bro."
Sent from my SAMSUNG-SGH-I317 using Tapatalk
Glad to hear. The wireless modem you have is indeed a great modem and you could use that alone but it is easier to just use your own. The installer more than likely wasn't on the up and up about the more technical aspects of the modem. You can't knock him for that part as the techs are not trained on a lot of the extra features of the modem. I only know this because I may or may not work for the company(need to keep work out of forums).
shelby04861 said:
I only know this because I may or may not work for the company(need to keep work out of forums).
Click to expand...
Click to collapse
I usually go with "I have a lot of experience with these products"

Categories

Resources