Database Develop

[Q] P1000 International unlocked doesn't see any simcard

Hi there,
I'm having an International P1000 that came unlockled with the following details.
PDA: P1000JVJM5
PHONE: P1000JXJM2
CSC: P1000OJVJM5
But every time I put in a sim card, it will reboot because it has detected a sim card. Then after starting up again it tells me that there is "No SIM card in device". I've tried it with 6 different sim cards, from different providers and even from a different country. All with the same result.
*#7465625# Tells me that all the locks are OFF.
Does anybody have any idea what could be the problem?

have u inserted the sim card fully and close off the simcard bay?
Or try shutting down completely and insert the sim card then power on?
If you have, sorry I have no Idea what could be wrong (hardware defect maybe?)
You would have to bring it back for warranty.

UNIQUE .. may you take ur tab to the samsung service center , maybe its hardware issue ..
can i ask u rude question based on how long you used the tab ( did u put the simcard correctly ? ? ? pls check .. another thing ,, if u bought the tab now , so u better go and replace it

PieWai said:
Hi there,
I'm having an International P1000 that came unlockled with the following details.
PDA: P1000JVJM5
PHONE: P1000JXJM2
CSC: P1000OJVJM5
But every time I put in a sim card, it will reboot because it has detected a sim card. Then after starting up again it tells me that there is "No SIM card in device". I've tried it with 6 different sim cards, from different providers and even from a different country. All with the same result.
*#7465625# Tells me that all the locks are OFF.
Does anybody have any idea what could be the problem?
Click to expand...
Click to collapse
Are you sure the tab is unlocked??
Try unlock it first.
That's my personal opinion.
Good luck
SGT Running Overcome 2.0.0 RC1

[Q] Sim Card Detection Problem

Hi all,
I am running
firm 2.3.3
base board p1000xxjpz
kernel 2.6.35.7 [email protected]
build gingerbread xxjq1
When it boots it asks for SIM card, i slip in the SIM card it gets detected then says its going to reboot. I reboots saying "install sim card" even thought the card is still in place. I pull card out then back in and it reboots and again "insert sim card" comes back. any ideas whats up with it ?
I was wiondering when i reflashed it, did i use the correct modem, is there anyway to tell which one should be used ....
cheers
K

tbw1 said:
Hi all,
I am running
firm 2.3.3
base board p1000xxjpz
kernel 2.6.35.7 [email protected]
build gingerbread xxjq1
When it boots it asks for SIM card, i slip in the SIM card it gets detected then says its going to reboot. I reboots saying "install sim card" even thought the card is still in place. I pull card out then back in and it reboots and again "insert sim card" comes back. any ideas whats up with it ?
I was wiondering when i reflashed it, did i use the correct modem, is there anyway to tell which one should be used ....
cheers
K
install samsung kis on your PC and upgrade tu 2.3.6 or you can flashed with odin
Click to expand...
Click to collapse

[Q] HELP SIM CARD Not recognized after flashing rom

Dear XDA I9070 experts I really need some help here.
First I want to apologize if I have some errors, my english is not very good, so sorry about that, I will try to do my best to explain and give the best background information if anyone can help me.
My actual phone is an Motorola Atrix 2, and I have flashed roms several times following the procedures explained on the threads here in this awesome site XDA step by step. So being able to flash roms with no problem at all I tried to do the same on my wifes old Samsung I9070.
I followed a thread that explained how to flash a ROM from GB to Kit Kat for the I9070 step by step here on XDA. The thread is this one:
http://forum.xda-developers.com/showthread.php?t=2198341
It all went fine but being that the phone was not being used by anybody I forgot to insert a SIM CARD before the flashing procedure. I really don't know if that makes a difference, but when the mobile booted the first time after the ROM flashing I inserted my SIM card and to my surprise I didnt recognized it... booted the phone again several times and nothing, but the SIM card is being detected right away on my Motorola.
So I tried to do some research about that and some people suggested to go back to stock firmware, and others told that it was a problem with the EFS folder.
So I tried going back to stock JB with ODIN, but this time with the SIM CARD inserted, and nothing, the same problem. So I tried inspecting the EFS folder and I think that is the problem but I need some advice on this.
The EFS FOLDER has this content:
A bunch of files named CRYPTPROP...
DECRYPT_KEY
ESSIV
GUARDFIL
NV.LOG
NV_DATA.BIN.MD5
And some folders inside... Thats all. I didnt made any backups of the phone or the EFS folder
So I tried using the code *#06# and it gives a valid IMEI 3544******* etc
I really don't know how the phone still shows a valid IMEI with the file NV_DATA.BIN missing, so I checked the phone information and found this:
Inside SETTINGS:
MODEL NUMBER: GT-I9070
ANDROID VERSION: 4.1.2
BASEBAND VERSION: I9070XXLQL
KERNEL VERSION: 3.0.31 - 1485715
BUILD NUMBER: JZO54K.I9070XXLQL
Inside SETTINGS - STATUS:
NETWORK: UNKNOWN
SERVICE STATE: OUT OF SERVICE
MOBILE NETWORK STATE: DISCONNECTED
MY PHONE NUMBER: UNKNOWN
IMEI: 3544******
Maybe the EFS folder is not all bad, I really dont know, please I need some advice here. My motorola screen is dying and I need to recover this one as it is a good phone. Thanks in advance for your help.

v_casas said:
Dear XDA I9070 experts I really need some help here.
First I want to apologize if I have some errors, my english is not very good, so sorry about that, I will try to do my best to explain and give the best background information if anyone can help me.
My actual phone is an Motorola Atrix 2, and I have flashed roms several times following the procedures explained on the threads here in this awesome site XDA step by step. So being able to flash roms with no problem at all I tried to do the same on my wifes old Samsung I9070.
I followed a thread that explained how to flash a ROM from GB to Kit Kat for the I9070 step by step here on XDA. The thread is this one:
http://forum.xda-developers.com/showthread.php?t=2198341
It all went fine but being that the phone was not being used by anybody I forgot to insert a SIM CARD before the flashing procedure. I really don't know if that makes a difference, but when the mobile booted the first time after the ROM flashing I inserted my SIM card and to my surprise I didnt recognized it... booted the phone again several times and nothing, but the SIM card is being detected right away on my Motorola.
So I tried to do some research about that and some people suggested to go back to stock firmware, and others told that it was a problem with the EFS folder.
So I tried going back to stock JB with ODIN, but this time with the SIM CARD inserted, and nothing, the same problem. So I tried inspecting the EFS folder and I think that is the problem but I need some advice on this.
The EFS FOLDER has this content:
A bunch of files named CRYPTPROP...
DECRYPT_KEY
ESSIV
GUARDFIL
NV.LOG
NV_DATA.BIN.MD5
And some folders inside... Thats all. I didnt made any backups of the phone or the EFS folder
So I tried using the code *#06# and it gives a valid IMEI 3544******* etc
I really don't know how the phone still shows a valid IMEI with the file NV_DATA.BIN missing, so I checked the phone information and found this:
Inside SETTINGS:
MODEL NUMBER: GT-I9070
ANDROID VERSION: 4.1.2
BASEBAND VERSION: I9070XXLQL
KERNEL VERSION: 3.0.31 - 1485715
BUILD NUMBER: JZO54K.I9070XXLQL
Inside SETTINGS - STATUS:
NETWORK: UNKNOWN
SERVICE STATE: OUT OF SERVICE
MOBILE NETWORK STATE: DISCONNECTED
MY PHONE NUMBER: UNKNOWN
IMEI: 3544******
Maybe the EFS folder is not all bad, I really dont know, please I need some advice here. My motorola screen is dying and I need to recover this one as it is a good phone. Thanks in advance for your help.
Click to expand...
Click to collapse
Your baseband is not missing, but anyway you can try this: http://forum.xda-developers.com/showthread.php?t=2677807
P.S. And you did factory reset after going from GB to JB?

shut_down said:
Your baseband is not missing, but anyway you can try this: http://forum.xda-developers.com/showthread.php?t=2677807
P.S. And you did factory reset after going from GB to JB?
Click to expand...
Click to collapse
Thank you very much for your help shut_down....
I followed all the steps and still No SIM... Insert SIM card message :crying::crying::crying:
And to answer your question... yes I did factory reset several times... wiped cache, everything... several times after flashing :crying:
Any other suggestions?, I really don't know what else to do... thanks in advance for your help and time.

What JB rom did you flash? Link? Perhaps any Baseband problem ... and where are you from?

Flo0008 said:
What JB rom did you flash? Link? Perhaps any Baseband problem ... and where are you from?
Click to expand...
Click to collapse
Thank you Flo0008 for you help... I used a firmware from Sammobile... this one exactly I9070XXLQL_I9070ITVLQ5_ITV as it was one of the more recent ones.
By the way I'm from Venezuela, but I bought the phone new and unlocked from amazon, the phone is in mint condition and my wife used it for more than a year without any problems, also we use the same carrier... it was not used anymore since December 2013 and recently I charged it for a full battery and did the firmware flashing and since then I'm facing the No SIM card, Insert SIM card message.
Could it be the firmware I selected I9070XXLQL_I9070ITVLQ5_ITV the problem?... It's from Italy... maybe you can recommend using another one.
Thanks in advance!

I had similar situation once when I tried different SIM card. My solution was to put SIM a bit twisted into its bed.
[\] instead of [|].
It took few tries but finally it got detected and working.
Sent from my SGS Adv. using xda-developers app.

most likely your phone was *not* SIM unlocked before you flashed it: I did the same thing to mine and read many similar stories here and there.
I never found a solution and bricked my phone while trying to fix it. I went up to copiing a full ROM dump from another working 9070P: the copy succeded and phone worked (IMEI cloned etc...) but still no SIM card recognized (it was a spare free one so not a problem
If I manage to achieve my unbrick procedure (http://forum.xda-developers.com/showthread.php?t=2701363), we might be able to fix that by reseting the full ROM to a valid state.

Facing the No Sim issues
i am facing the same problem, and it was all of a sudden."No SIM"
I sent the phone to service center, but they failed to repair.
i have tried everything, hard reset, downgrade to GB, upgrading again to JB (via ODIN), custom ROMs, but no luck.
what i figured out is my phone works on some older SIM cards, which have square shaped Chip (like the one in BSNL sim).
any suggestions????

"no SIM card detected" after using Flashtool

Hello World,
As I'm a stupid boy, I've used flashtool to downgrade a Xperia Z to a rootable firmware Xperia Z_10.3.1.A.2.67_SFR 4.2.2.ftf
I've then used rootkitXperia_20140719 and XZ-lockeddualrecovery2.8.3-RELEASE.installer
Reboot, every thing seems ok except that my SIM card is no more detected. "Please insert a SIM card and restart your phone".
The SIM card works well in another phone. But I've never used it in the Xperia Z. IMEI is still correct in Xperia.
Why am I stupid ? Because I don't have any backup. So, what could I do now ? I've try touse flashtool to flash other stock roms or baseband without success. :crying:

Really stupid. I found what I've done wrong: I've used Flastool fastboot mode on locked bootloader...
Any idea to solve ?

Me too

Did you find a solution?????

puneet0009 said:
Did you find a solution?????
Click to expand...
Click to collapse
No

Yes, I found a solution: The SIM card was not well inserted. Change the side when inserted (electronic part should back oriented) and everithing works well.

No service, no imei, no baseband after rebooting

I just got an old htc ph39100 and it met some troubles like this. After rebooting, it usually lost imei and baseband so my phone has no service. But if I try to reboot many times, finally it has service and Imei and baseband too. But if I turn off or restart my device, it has same troubles again.
I tried to flash RUU file to come back stock rom but it doesn't solve the problem
So anyone can help me to fix this?

kulomo said:
I just got an old htc ph39100 and it met some troubles like this. After rebooting, it usually lost imei and baseband so my phone has no service. But if I try to reboot many times, finally it has service and Imei and baseband too. But if I turn off or restart my device, it has same troubles again.
I tried to flash RUU file to come back stock rom but it doesn't solve the problem
So anyone can help me to fix this?
Click to expand...
Click to collapse
Check your Sim card slot... Make sure your card fits tight... Maybe push down on the metal that the Sim card rides in

rignfool said:
Check your Sim card slot... Make sure your card fits tight... Maybe push down on the metal that the Sim card rides in
Click to expand...
Click to collapse
I checked a lot of times but no luck. I just wondering if it's sim card slot problem, so why my device doesn't recognize IMEI, baseband? After many many times try to reboot, some how it have service again and IMEI and baseband appear. But all of them were lost after rebooting.

kulomo said:
I checked a lot of times but no luck. I just wondering if it's sim card slot problem, so why my device doesn't recognize IMEI, baseband? After many many times try to reboot, some how it have service again and IMEI and baseband appear. But all of them were lost after rebooting.
Click to expand...
Click to collapse
SIM stands for Subscriber Identity Module....
If the information you are talking about is missing... Its usually because the gold contact on the card isn't making a connections to the gold pins in your phone... Especially when its intermittent...
Try this...
Take the back cover off the phone with the power off... Push down LIGHTLY on your SIM slot and hold it... Then push power... If the slot is under the battery... Try a little shim under the battery on top of the SIM slot... We are just trying to push down on the card a little...