I have tried my stock battery, an extended battery, and then another battery I ordered online. Whenever I plug it in the charging light lights up foe a couple seconds, then goes out. When I try to charge from my computer, win7 will make the noise of a detected device, then disconnected device, then when unplugged makes the disconnected device noise again.
You Should try another cable and see if anything changes.. sounds like cable might be going bad. I had that issue, it would only pick it up at certain spots and when it moved nothing was happening
Sent from my HTC PH39100 using xda app-developers app
Another good solution is to buy an external charger. They are fairly cheap on Amazon. I had my Vivid do the same thing, took the battery out and charged it in an external I have, put it back in and it was fine. It seems that sometimes the Vivid forgets about charging when the battery has hit some magic point, and the only way to reset it is to charge the battery externally.
Related
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
jvillejoe said:
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
Click to expand...
Click to collapse
what are you charging from? are you using the stock nook cable and plug?
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
altimax98 said:
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
Click to expand...
Click to collapse
Yeah seems to me thats what it must be I'll post back what I find out.
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
RobertsDF said:
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
Click to expand...
Click to collapse
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
jvillejoe said:
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
Click to expand...
Click to collapse
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Non-Standard chargers...
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
danger-rat said:
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Click to expand...
Click to collapse
I never used another charger besides the stock charger that came with the NC. Up until this happened all that was ever used was the stock cable for charging. I only used another charging cable once I ran into these problems cause I figured the cable was damaged. Its happened to me before with other devices. But the same results happen with every cord I use. When I plug it in it lights up and shows the red battery screen. So that tells me that the cord or USB port couldn't be the problem. Cause its clearly getting power its just not charging.
Fattychance said:
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
Click to expand...
Click to collapse
When charging I can not turn the screen off it's stuck on the screen with a red battery.
jvillejoe said:
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
Click to expand...
Click to collapse
No. They sell it without one...the 8GB internal storage is enough for looooottts of books. The microsd was just a nice + for people with lots and lots of music.
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
bstock said:
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
Click to expand...
Click to collapse
Thanks for the feed back. I'm wondering by un-pluging the battery from the nook if it resets it. Kind of like if a phone freezes or if your computer freezes and you pull the battery. Seems like a plan. Not sure if this is what I'll do as I'm sure its still under warranty. If it comes back and its not covered or B & N wont replace it I guess thats my only hope.
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
CLMT said:
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
Click to expand...
Click to collapse
If your not worried about voiding the warranty then sure I guess its worth a shot.
So I got it fixed right. All it was was a faulty cable lol!
jvillejoe said:
So I got it fixed right. All it was was a faulty cable lol!
Click to expand...
Click to collapse
I had this problem too, but I'm not sure "faulty" is the right word for the cable.
My friend borrowed my nook and returned it with a dead battery (Thanks asshole). So I plugged it into my computer at work and just got the always-on low battery message. After 45 minutes I took it to my car so I wouldn't forget it. I plugged it into my USB charger in the car using a different cable. Two hours later, same state.
When I got home I pugged it into the Nook wall charger with yet another cable (not the nook's original) and got the same thing. I searched here to see if I could figure out what was going on and decided to try the original cable with the wall plug. literally two seconds after plugging it in it started booting into Froyo.
I'm sure I didn't have four "faulty" cables. I think those that are saying you should be using the original are correct. The others worked fine when the battery wasn't empty, but mine only responded to the original once it got to the point of the unending low-battery message.
Original charger / cable required with totally empty battery
Same here. With battery completely empty and non standard cable,stuck at red battery sign forever. With orginal cable, boots fine and charges.
solution I found
Have CM7 installed on SDCard, got the battery icon, even with the unit plugged into the charger with oem equipment. Held the power button 'til the unit turned off completely, removed the sdcard, rebooted. Nook booted into stock fine, turned off, re-inserted sdcard and rebooted. All is well.
my vivid was wroking 100% fine, when i pulled it out of my pocket it was dead. i replaced the battery, and i also notice no mater what source i charge it from (USB or USB tethered)
completly out of the blue and im at such a loss... i work as a salesmen for AT&T and i went down the whole troubleshooting guide and still nothing but a b;ac;it scrren with nothing to light up
any thoughts? i just wanna charge it lol
Swap your battery with one at the store that is charged. Then you can diagnose if its truly your phone or something with your charger or cord.
Maybe you put keys or some other object in your pocket with your phone that borked your phone's USB port.
sent from my HTC Vivid using XDA app premium
Yesterday my phone shutted because my battery, I connected to my car and charged a while, I got out from charging and using 2-3 minutes more and battery died again. When I got home I connected it to AC power and powered on, It was working without problem. I left my phone maybe 1 hour charging and when I took it again it was dead: screen dead, no life signal, just the led blinking slowly when connected to power (either AC and USB)...tried to take off battery but nothing. Today I connected it to PC and windows has recognized it but cannot identify it (on the PC the classic USB device not recognized error with yellow triangle on top) and the led is always blinking.
Any idea? should I have to buy a new phone?
thanks
Sounds like your battery is dead. Try replacing your battery
Sent from my HTC Incredible S using xda app-developers app
mohdsubaie said:
Sounds like your battery is dead. Try replacing your battery
Sent from my HTC Incredible S using xda app-developers app
Click to expand...
Click to collapse
Do you think is a battery problem? phone should boot even without a battery when connected to power...or not?
ledzgio said:
Do you think is a battery problem? phone should boot even without a battery when connected to power...or not?
Click to expand...
Click to collapse
Try Running some POST tests. As in, Power off your device and wait for few seconds. Then Press and hold your power key and your volume down key. You should be able to access your Bootloader. (If you have Rooted your device, you could access your recovery and clear the battery stats although your device's condition seems peculiar/critical). Its worth a shot If you ask me.
I have already tried it but nothing, cleared dalvik and battery stats..I cannot understand whats going on. Now phone is working again but it cannot maintain battery, I mean I kept it in charge all the night but when I power on the phone it shuts down just when it starts android (thats strange because I went to a store yestarday and tried a new battery but it didn't worked, when got home I tried to power on it again and it started)...this is driving me crazy!!
edit: I turned it on, plugged in AC charger and phone after some minutes told me that (I don't remember the exact message) power needed by the phone is more than the charger could provide...
edit2: now it is on and it is charging (USB) and it doesn't charge more than 21%...really strange
Odd that this hasn't been mentioned but perhaps try a different usb cable? Different port? Seems obvious but you never know. Cables can deteriorate.
Sent from my HTC Incredible S using xda app-developers app
TheMegosh said:
Odd that this hasn't been mentioned but perhaps try a different usb cable? Different port? Seems obvious but you never know. Cables can deteriorate.
Sent from my HTC Incredible S using xda app-developers app
Click to expand...
Click to collapse
I have tried 3 different cables and 2 different computers...same result. I have flashed a new ROM, plugged in for charging and now is stuck on 15% battery (5 minutes aga was 16%, it discharges while plugged in).
Ok maybe here is a solutions:
http://forum.xda-developers.com/showthread.php?p=26492940#post26492940
What do you think about?
Hi everybody...
I have an issue for you...
Yesterday I was using my phone and battery was aboout 40%.
I then took out it from my pocket to switch on the screed and it didn't switch on...it seems the screen was on but black...
- I tried to press the switch button, but nothing...I connected it to my portable battery and nothing too...
- I tried to switch on by press all three phisical buttons and I had a short vibration and nothing else, just another vibration after about 20sec...
That makes me feel that situation was possible to fix...
Of course the battery couldn't be removed and put on again...
Finally I arrived home and I connect to electricity and nothing, I connected to my PC and I reboot the phone by the utility: it works!!
I was worried and I would like to know what happened and if that's possible to repeat again...
Thanks!
Sent from my DROID4 using xda app-developers app
This phone doesn't play nice with a lot of portable battery chargers. Try it with the charger that came with it?
A short while after you plug the charger in, it should appear to boot and display only a charging screen. Once it gets to 10% or 15% you can pull the charge cable out, power it on normally and then plug the charge cable back in.
Oddly, Nokia micro USB chargers seem to work well with this phone, if you have one of those spare.
Hi!
thanks for the answer, but you maybe misunderstood, I know about difference between charging from portable charger and normal...it happened with my backflip when it was completely empty...
Maybe I didn't explain well...the phone went "off" alone, but I was sure battery was about 30%...and it didn't work, just the screen on and black...
In my case even normal charger didn't work to reboot phone...
My solution was just to connect to computer and reboot with the tool...
but I don't know what happened, till now it didn't happen again...
p.s. I have a portable charger bought on groupon, that it works, but it's extremely slow...
bye!!
Sent from my DROID4 using xda app-developers app
Well im pretty good with electronic, dis assembly and reassembly... however I may have bit the farm here. I replaced my digitizer for my device and the adhesive I purchased wasnt good enough so it was causing touch screen issues... So I took it all apart again and put it all back together to find OMG it wont turn on? Fully charged battery so I know thats not the issue and everything seems to be put in the right place (as if there is any other way to re-assemble this phone)....
So I did some trouble shooting... I tried switching to an original charger, attempted hard reboot assumed maybe the device was confused... left it on the charger as if god himself removed the remaining battery life all to no avail... However one thing I did notice is that for a while when the device was unplugged and sitting there the LED light would periodically blink red... hmm couldnt find anything on that ... Also when I remove the battery leads and plug it in the LED light illuminates green and stays that way regardless there still is no function to the phone literally a blank screen... I checked the screen and digitizer for damages both on its leads and the devices themselves and found there to be nothing wrong with them...
Im pretty sure I know the answer Im just hoping that Im wrong..
Also heres something Ive noticed as well, that when I plug both the phone in and leave the battery in it gets dangerously hot like battery about to explode hot after about 10 minutes or so
Berrabus said:
Also heres something Ive noticed as well, that when I plug both the phone in and leave the battery in it gets dangerously hot like battery about to explode hot after about 10 minutes or so
Click to expand...
Click to collapse
I buy broken Atrix HDs off of eBay all the time so I may be able to help. I've noticed that even though the battery is fully charged, when replacing the digitizer, the phone will think it's dead until it hits 100%. I usually have to hold the power button a Lil longer than normal, and when it turns on it will say 1% bat, remaining. It will charge the remaining battery and instantly jump to 100% when it's full.
Tl;dr: hold power until it turns on, charge to 100%
Markyzz said:
I buy broken Atrix HDs off of eBay all the time so I may be able to help. I've noticed that even though the battery is fully charged, when replacing the digitizer, the phone will think it's dead until it hits 100%. I usually have to hold the power button a Lil longer than normal, and when it turns on it will say 1% bat, remaining. It will charge the remaining battery and instantly jump to 100% when it's full.
Tl;dr: hold power until it turns on, charge to 100%
Click to expand...
Click to collapse
Well heres the thing. I already have been using the phone since Ive replaced the digitizer and its functioned relatively properly (aside from the adhesive not holding the digitizer down) the thing that concerns me is when I hook the battery back up to it and plug the phone in it gets dangerously hot like literally to the point where I question weather or not its going to explode also it doesnt show any LED function with the battery connected.
Go through and double check all of your connections. Also, connect it to your computer and see what device manager says.
Sent from my MB886 using xda premium
darknessrise1234 said:
Go through and double check all of your connections. Also, connect it to your computer and see what device manager says.
Sent from my MB886 using xda premium
Click to expand...
Click to collapse
Checked, rechecked and triple checked the connections as you know with the MB886 the connections only go one way and they either are in or not theres no middle-man. Unfortunatly my data-cable is not functioning so I cannot hook it up to the PC at the moment however I assume that if there is no function or charge with it just being plugged into the power cable then likewise would result from a PC connection. Not to mention the unexplained heat... like Im saying its almost to hot to hold kinda heat..
Well, last one I bricked it would be green light anytime it was plugged in and it had a specific register on the device manager.
Sent from my MB886 using xda premium
darknessrise1234 said:
Well, last one I bricked it would be green light anytime it was plugged in and it had a specific register on the device manager.
Sent from my MB886 using xda premium
Click to expand...
Click to collapse
When I plug it into my computer it says USB INPUT DEVICE RECOGNIZED DRIVERS INSTALLED CORRECTLY! To me that all sounds posative! Question is where to from here?
Thats with the battery out... When I hook the battery up it immediatly begins to get warm and recognizes as a Motorola USB Composite Device then starts disconnecting/reconnecting... Also during this process I noticed that the aluminum battery chassis is cracked right where the battery connects to the unit...
Do you have a second battery? If so, test the other battery. Otherwise, I am out of thoughts.
Sent from my Atrix HD using xda premium