PRL problems? - One (M7) Q&A, Help & Troubleshooting

I recently unlocked my bootloader and rooted my phone with TWRP using hasoons toolkit.
I can't seem to change my PRL when following the steps in the forum below I'm not sure what the problem is.
it does say the following "NOTE: This will only work on sense roms with epst support." I'm currently rooted but still on my stock rom, could that be the issue?
http://forum.xda-developers.com/showthread.php?t=2296167
As the thread above suggested, I used Kernal Tuner to change the ro build type
like this
ro.build.type user
to
ro.build.type dev
I put a downloaded PRL file in the my phones storage and restarted my phone and when I attempted to use the dialer by typing
##778# nothing would happen.. No menu comes up or anything? what am I doing wrong?
Is there another way to change the PRL for the sprint HTC one? I'v been trying to figure this out for probably the past 2 hours. It's brutal
.
** I just also wanted to make a note, that when I change from "user" to "dev" after I restart, or shut down my phone and turn it on again

This isn't the sprint forum for the HTC one. I don't think anybody can help you here.
Sent from my One using Tapatalk 4

Tw1tchy said:
This isn't the sprint forum for the HTC one. I don't think anybody can help you here.
Sent from my One using Tapatalk 4
Click to expand...
Click to collapse
sorry. I'll repost this in the sprint forum

Related

Using a droid3 on straight talk

Has anyone done this yet I'm getting one that is unlocked and works with att sim card and I know straight talk works on att towers so I should just put the sim in and update the apn correct? Thanks
Sent from my Milestone using XDA
d3adbroke said:
Has anyone done this yet I'm getting one that is unlocked and works with att sim card and I know straight talk works on att towers so I should just put the sim in and update the apn correct? Thanks
Sent from my Milestone using XDA
Click to expand...
Click to collapse
It works. You just need to follow the directions on how to get it set up for ATT. Stick to a GB rom too as I'm not sure if you're able to edit APN settings in ICS.
Okay thanks what would u say would be best gb rom for battery and speed?
Sent from my Milestone using XDA
rquinn19 said:
It works. You just need to follow the directions on how to get it set up for ATT. Stick to a GB rom too as I'm not sure if you're able to edit APN settings in ICS.
Click to expand...
Click to collapse
You could always just push a complete apns-conf.xml to /etc (in gb or ics) and it will be perm setup, even if you factory reset. There's one on code.google or docs.google, just search "complete apns-conf.xml" or take one from any att rom from an att android device.
Willis111 said:
You could always just push a complete apns-conf.xml to /etc (in gb or ics) and it will be perm setup, even if you factory reset. There's one on code.google or docs.google, just search "complete apns-conf.xml" or take one from any att rom from an att android device.
Click to expand...
Click to collapse
I tried that without success on ICS before. Maybe permissions weren't setup? Who knows? I've got ICS running with data now after doing these changes without having to edit my APN settings.

[Q] Need Original Boot.img wifi will not turn on

I hope someone can help. I have a rooted HTC VIVID, Android 4.0.3, HTC Sense 3.6, Kernel 3.016-g1739124
I installed twrp and tried to flash a few different roms. I never could get it to work so I restored my phone to stock. I guess I don't have the correct boot.img since my wifi does not turn on.
Can someone post the correct boot.img for me, or tell where to go?
If you are not in US. Maybe with changing country region code it solve and WiFi work
Sent from my Holiday using xda app-developers app
l0000l said:
If you are not in US. Maybe with changing country region code it solve and WiFi work
Sent from my Holiday using xda app-developers app
Click to expand...
Click to collapse
I am in the US. I did see something about editing my nvram.txt file but I did a search using astro file manager and i can't find one.
If you installed cm10 already.
Do this maybe it work
Be sure WiFi is fully off ( not stucking in 'WiFi turning on')
Before you try to turn WiFi on . Go to WiFi advance menu and choose change country region code and choose new one ( not default)
And try to turn on wifi
Sent from my Holiday using xda app-developers app
I don't have that option under advanced wi-fi
O and CM10 does not support the VIVID
Moved to Q&A
Please post in the correct section next time
Moderating from my One Xl
I use cm10 pacman
Setting>WiFi(be sure WiFi is fully off)>press menu button(near home button downside of phone)>now menu show with 5 option choose advance> now change region code
Sent from my Holiday using xda app-developers app
l0000l said:
I use cm10 pacman
Setting>WiFi(be sure WiFi is fully off)>press menu button(near home button downside of phone)>now menu show with 5 option choose advance> now change region code
Sent from my Holiday using xda app-developers app
Click to expand...
Click to collapse
This is only available in the aosp JB roms. ICS Sense builds won't have that option.
Well I never could get any of the roms to load so I gave up and tried to go back stock. I did do a search and there is no nvram.txt on my phone. I can't seem to find a copy of one for a VIVID online and I can't seem to find the original boot.img I guess I will have to live without wifi.
techxx said:
Well I never could get any of the roms to load so I gave up and tried to go back stock. I did do a search and there is no nvram.txt on my phone. I can't seem to find a copy of one for a VIVID online and I can't seem to find the original boot.img I guess I will have to live without wifi.
Click to expand...
Click to collapse
run the ruu on your computer, but stop at the first step with a next or continue button. hit start/run and type %TEMP% and hit enter
sort by date, newest first. In the first folder should be a ROM.zip that should contain boot.img
homeslice976 said:
This is only available in the aosp JB roms. ICS Sense builds won't have that option.
Click to expand...
Click to collapse
I say if he use jelly ROM he can use this option
For ICS you can use 'wifix manager' that can change region code
All of this that I say is only a guess
Sent from my Holiday using xda app-developers app
I started the RUU without the phone hooke up. No Zip. I then Hooked up the phone and went to the very last step, unhooked the phone and then clicked next. Still no zip. I have been told before that if my phone is rooted then I can't use the RUU or I will brick it. Is this true? If it's not true then I don't have any issues going ahead with the using the RUU.
No that's not true. Relock your boot loader, boot to fast boot, plug in your phone, run ruu
Sent from my Holiday using Tapatalk 2
I tried the wifi fix manager but that didn't solve my issue either. I appreciate you guys trying to help me.
I relocked my phone but I can't get past my boot loader now. I tried to go ahead and run the RUU but it said I had an incompatible phone.
techxx said:
I tried the wifi fix manager but that didn't solve my issue either. I appreciate you guys trying to help me.
Click to expand...
Click to collapse
For the last sentence
How to use wifix :
Be sure WiFi is fully off
Install wifix
Run and install driver
Go out and in phone dial *#94349# ( I think, search about this code). A little text must be shown in buttom of screen 'wifix engaged'
now try to turn WiFi on
All of I do for working wifi for me is this, if you are s-off or installed boot file through adb
Sent from my Holiday using xda app-developers app
OK I figured out the issue. The version of twrp I was using had issues with my VIVID so I switched to the latest cwm and I was able to upload ROMS and get my wifi running again.

[Q] No signal, phone does not recognize sprint as network

Rooted and was running cm 10.2 stable, reset the phone over the weekend while trying to switch devices with sprint to unlock my old device. Ever since I have not had sprint signal, my bars just have an X, MDN and MSID are empty and can't recognize sprint as network. Went back to stock using RUU, phone currently does not say tampered just relocked. Any suggestions?
oddjob727 said:
Rooted and was running cm 10.2 stable, reset the phone over the weekend while trying to switch devices with sprint to unlock my old device. Ever since I have not had sprint signal, my bars just have an X, MDN and MSID are empty and can't recognize sprint as network. Went back to stock using RUU, phone currently does not say tampered just relocked. Any suggestions?
Click to expand...
Click to collapse
Seems like you might need to get with sprint and reconnect your one to your sprint account.
Sent from my One using xda app-developers app
MrFixit007 said:
Seems like you might need to get with sprint and reconnect your one to your sprint account.
Sent from my One using xda app-developers app
Click to expand...
Click to collapse
I'll have to try now that it doesn't say tampered anymore...yesterday I dropped by with a stock rom and they couldn't get it back on the network.
Same issue on mine
I'm having the same exact issue. Had been working fine on Paranoid Android for weeks, and suddenly lost CDMA completely. MSID and MDN are None, and I get a commit failed error if I try to reenter them. Unfortunately, in my troubleshooting, I RUU'd back to stock 1.29, but then let it update to 1.31, without doing the S-OFF exploit, so now I can't get S-OFF and remove the 'Tampered' message. The Sprint store that I went to wouldn't even look at it because it had been unlocked. Will try again at another Sprint store with some less pompous techs.
WiFi, GPS, and even LTE (in the 2 square blocks where I can get it) work fine. When on a CM based ROM, if I change mode from RUIM/SIM to NV, I can actually get a CDMA signal.
oddjob727 said:
I'll have to try now that it doesn't say tampered anymore...yesterday I dropped by with a stock rom and they couldn't get it back on the network.
Click to expand...
Click to collapse
beanpoppa said:
I'm having the same exact issue. Had been working fine on Paranoid Android for weeks, and suddenly lost CDMA completely. MSID and MDN are None, and I get a commit failed error if I try to reenter them. Unfortunately, in my troubleshooting, I RUU'd back to stock 1.29, but then let it update to 1.31, without doing the S-OFF exploit, so now I can't get S-OFF and remove the 'Tampered' message. The Sprint store that I went to wouldn't even look at it because it had been unlocked. Will try again at another Sprint store with some less pompous techs.
WiFi, GPS, and even LTE (in the 2 square blocks where I can get it) work fine. When on a CM based ROM, if I change mode from RUIM/SIM to NV, I can actually get a CDMA signal.
Click to expand...
Click to collapse
will there be a problem servicing/exchanging it with the relocked message? the tampered and security warnings are gone, i'm still within the 2 week return period
I think it depends on which tech you get and there mood. Many people have had no issue getting warranty repair on unlocked phones. As I said, even though I was restored back to stock, the tech wouldn't even look at it, as he claimed I could have loaded a bad ROM that damaged the radio. I don't think that the 2 week window would apply to you, since you've unlocked the bootloader.
oddjob727 said:
will there be a problem servicing/exchanging it with the relocked message? the tampered and security warnings are gone, i'm still within the 2 week return period
Click to expand...
Click to collapse
beanpoppa said:
I'm having the same exact issue. Had been working fine on Paranoid Android for weeks, and suddenly lost CDMA completely. MSID and MDN are None, and I get a commit failed error if I try to reenter them. Unfortunately, in my troubleshooting, I RUU'd back to stock 1.29, but then let it update to 1.31, without doing the S-OFF exploit, so now I can't get S-OFF and remove the 'Tampered' message. The Sprint store that I went to wouldn't even look at it because it had been unlocked. Will try again at another Sprint store with some less pompous techs.
WiFi, GPS, and even LTE (in the 2 square blocks where I can get it) work fine. When on a CM based ROM, if I change mode from RUIM/SIM to NV, I can actually get a CDMA signal.
Click to expand...
Click to collapse
NV is the default. How was it set to RUIM/SIM?
It's supposed to be NV? On my Verizon Galaxy S3, the subsciption is RUIM/SIM. There was/is a bug in CM where it would switch to NV after a factory reset and I would have to manually change it to RUIM/SIM to get data to work again. I thought that Sprint uses the same setting.
david279 said:
NV is the default. How was it set to RUIM/SIM?
Click to expand...
Click to collapse
Verizon and sprint and different. Your on our team now. Leave that alone.
Sent from my One using Tapatalk 4
oddjob727 said:
Rooted and was running cm 10.2 stable, reset the phone over the weekend while trying to switch devices with sprint to unlock my old device. Ever since I have not had sprint signal, my bars just have an X, MDN and MSID are empty and can't recognize sprint as network. Went back to stock using RUU, phone currently does not say tampered just relocked. Any suggestions?
Click to expand...
Click to collapse
I had the same problem and then flashed it to 2.3.6 Gingerbread... And now everything works well..
Sent from my GT-I9000 using xda app-developers app
Gingerbread?
Sent from my One using Tapatalk 4
david279 said:
Gingerbread?
Sent from my One using Tapatalk 4
Click to expand...
Click to collapse
You know.. super yummy desert. goes well with whip cream.whip cream. whip cream. whip.. whip. whip. whip. YOU'RE EATING HAIR!!!
Actually, I'm on both teams. I also have a Verizon phone. The Sprint one is for work. Hence, the lack of a panic that my Sprint phone isn't working for the moment.
Since there is no way to choose between NV and RUIM/SIM in stock, I wonder if the radio is stuck in that mode from when it was changed in CM. I'll try switching back to CM, changing to NV, and then flashing back to stock to see if it fixes it, or at least will let me reenter my MDN/MSID.
As for Gingerbread- I didn't know that there was a GB ROM for the one, since when it was realeased, we were already on JB.
david279 said:
Verizon and sprint and different. Your on our team now. Leave that alone.
Sent from my One using Tapatalk 4
Click to expand...
Click to collapse
david279 said:
Gingerbread?
Sent from my One using Tapatalk 4
Click to expand...
Click to collapse
Yeah Gingerbread but now again rooted to 4.3 super nexus.. Mott much functions but fast and smooth
Sent from my GT-I9000 using xda app-developers app
Solved
david279 said:
NV is the default. How was it set to RUIM/SIM?
Click to expand...
Click to collapse
David- Thanks for the subscription information. That turned out to be the issue. I had changed it to RUIM/SIM because I wasn't getting any signal (probably just because of a local Sprint issue) and I figured that was the problem. Since that didn't fix the issue, I RUU'd back to stock. It seems that when you change the subsciption setting in the radio, it's not a setting that's corrected when you flash a stock RUU. And once on the stock RUU, there's no option to change the setting (unless it's in a hidden ## option).
To fix the issue, I reflashed back to CM, changed to NV, and then RUU'd back to stock. Once on stock, it went through the handsfree activation (which it wouldn't even try before I fixed that setting) and now 3G/CDMA are working again.
oddjob27- Maybe you should give this a try before trying to return it.
Yea I've heard of those Verizon issues but we don't have that.
Sent from my HTCOne using Tapatalk 4
beanpoppa said:
David- Thanks for the subscription information. That turned out to be the issue. I had changed it to RUIM/SIM because I wasn't getting any signal (probably just because of a local Sprint issue) and I figured that was the problem. Since that didn't fix the issue, I RUU'd back to stock. It seems that when you change the subsciption setting in the radio, it's not a setting that's corrected when you flash a stock RUU. And once on the stock RUU, there's no option to change the setting (unless it's in a hidden ## option).
To fix the issue, I reflashed back to CM, changed to NV, and then RUU'd back to stock. Once on stock, it went through the handsfree activation (which it wouldn't even try before I fixed that setting) and now 3G/CDMA are working again.
oddjob27- Maybe you should give this a try before trying to return it.
Click to expand...
Click to collapse
beanpoppa, david you guys saved my ass thank you so much did the trick!

Flashed wrong rom... need ruu for 1.31.651.2

So while having twenty tabs open and sifting through a bunch of dead threads and guides with dead links. I ended up downloaded a stock rom from the main htc one forum and didn't notice. I thought I was in the Sprint section the whole time.
Now my backup does not work, it boots but I can only see the notification bar and it reboots after like a minute. Installing other roms does the same thing so I am assuming the partitions are borked.
I can still get into twrp, I can unlock and relock the bootloader and adb etc.
My current version is 1.31.651.2
Could someone please provide me with some info on getting this fixed. The only thing I wanted to do was unlock the phone, I called sprint and they gave me the unlock code but I could not find where to enter it. After research I read you need root, and unlock helper. And now here I am haha.
Did you get squared away, or are you still out there on that lonely, over populated island?
Sent from my HTCONE using Tapatalk
---------- Post added at 08:58 AM ---------- Previous post was at 08:57 AM ----------
bowenac said:
So while having twenty tabs open and sifting through a bunch of dead threads and guides with dead links. I ended up downloaded a stock rom from the main htc one forum and didn't notice. I thought I was in the Sprint section the whole time.
Now my backup does not work, it boots but I can only see the notification bar and it reboots after like a minute. Installing other roms does the same thing so I am assuming the partitions are borked.
I can still get into twrp, I can unlock and relock the bootloader and adb etc.
My current version is 1.31.651.2
Could someone please provide me with some info on getting this fixed. The only thing I wanted to do was unlock the phone, I called sprint and they gave me the unlock code but I could not find where to enter it. After research I read you need root, and unlock helper. And now here I am haha.
Click to expand...
Click to collapse
Sent from my HTCONE using Tapatalk
Follow this guide
http://forum.xda-developers.com/showthread.php?p=44243635
Just a heads up as you are following the commands you will see strange text and also an error, but just keep going and it will work.
Sent from my HTCONE using xda app-developers app
Konfuzion said:
Follow this guide
http://forum.xda-developers.com/showthread.php?p=44243635
Just a heads up as you are following the commands you will see strange text and also an error, but just keep going and it will work.
Sent from my HTCONE using xda app-developers app
Click to expand...
Click to collapse
Thank you, took a few trys but it worked. +10000
Glad your back up and running.
Sent from my HTCONE using xda app-developers app
Konfuzion said:
Glad your back up and running.
Sent from my HTCONE using xda app-developers app
Click to expand...
Click to collapse
Now do you know of a way to actually unlock the phone to be used on gsm?
I tried this http://forum.xda-developers.com/showthread.php?t=2491840 that didnt work. So now I just restored my original twrp backup that I made after getting it back up. So now I am on 4.1.2 sense 5 original from the ruu and just install SU.
If anyone could point me in the right direction of getting this phone unlocked and working correctly that would be great.
EDIT:
I just noticed after getting it back up with the ruu I am now able to select GSM from mobile data. Before it always said it was sim locked and wouldnt let me choose it.
APN shows T-Mobile Data cinet.spcs and T-Mobile MMS epc.tmobile.com
When I go to Available GSM Network and search networks it shows T-Mobile and AT&T when I choose T-Mobile it tries to register the network for ever then it gets registed and shows T-Mobile as the Available GSM Network but then it gets removed. I was able to make one test call and it worked but then was removed.
Through out all of this I keep getting a message to Change Mode No Network Found Select Yes to switch to global mode, no to stay in current mode. Nothing seems to be working though.
Thanks in advance to anyone who can help me figure this out.
Hmm seems to have stuck this last time I selected T-Mobile. We will see how long it last. I just want to make sure I have done everything correctly. I would like to get updated to the latest stock plus root rom.
Here are some screenshots.
http://i880.photobucket.com/albums/ac7/bowenac/Screenshot_2013-11-05-11-46-03_zps1ddadb6e.png
http://i880.photobucket.com/albums/ac7/bowenac/Screenshot_2013-11-05-11-46-10_zpsa1b83cfb.png
EDIT:
Nope now its gone, I keep having to select T-Mobile and it only works for a couple minutes. Any ideas?

[Q] Messed with My Sprint HTC One while adding Revolution HD 41.0

Hi,
Please help me as I tried to solve the problem with different ways and I totally messed my phone. I am very new to this.
I was running with benny's 4.3 version on my Sprint HTC One.
I downloaded Revolution HD 41.0 and used TWRP 2.6.3.0 after entering into recovery mode.
I had taken back before this. So, everything installed well. However, after reboot phone stuck on the boot screen.
I tried to find the answer. However, when I did not find it, I restored to my earlier backup.
After restoring I started facing reboot problem. So, I again tried ARHD 41.0, by wiping the data.
It again stuck on boot screen. I tried it again and again. And once formatted the device.
Later I read somewhere and copied rom again to phone by using ADB.
However, phone was getting stuck on boot screen. So , I tried to update TWRP to 2.6.3.3.
I used (twrp-2.6.3.3-m7.img) to do the same. And now my phone is not even going in recovery mode, it just restarts as I think this was the wrong TWRP version.
I cannot think any thing now. Please help. This is my new phone.
Please ask if any details required. I do not know what details to add.
Thanks in advance...
ARHD no longer supports GSM. You have to follow this guide http://forum.xda-developers.com/showthread.php?t=2503646
Sent from my HTCONE using Tapatalk
Last I knew, 41 wasn't running on Sprint ... only up to 31.6. Same with TWRP 2.6.3.3 .
I think Ecliptic is the only Sense based Kit Kat ROM for now
elvisypi said:
ARHD no longer supports GSM. You have to follow this guide http://forum.xda-developers.com/showthread.php?t=2503646
Sent from my HTCONE using Tapatalk
Click to expand...
Click to collapse
Hi,
I am following the steps in the link. Kindly suggest which ROM should I use ? Is InsertCoin 6.0-x fine ?
Thanks.
raviksingh said:
Hi,
I am following the steps in the link. Kindly suggest which ROM should I use ? Is InsertCoin 6.0-x fine ?
Thanks.
Click to expand...
Click to collapse
Yes tou ca use IC up to 6.0-5. Don't use 7.0... cause it doesn't have Sprint support
Sent from my HTCONE using Tapatalk
elvisypi said:
Yes tou ca use IC up to 6.0-5. Don't use 7.0... cause it doesn't have Sprint support
Sent from my HTCONE using Tapatalk
Click to expand...
Click to collapse
Thanks. I am now able to go to TWRP. I will use IC 6.0-5.

Categories

Resources