{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
INFORMATION
According to info that I found
around on the net the Galaxy
Pop Plus (GT-S5570I) is completely
different from the Galaxy mini/pop (GT-
S5570) or the two terminals to the
external appearance are different in
hardware since the Galaxy Pop Plus is more
similar to Galaxy Y.
FEATURES
Processor: ARMv6 rev 5 - 832Mhz
RAM: 362 MB - 72MB Reserved
GPU: Broadcom Videocore 4
NAND: 512
system: stl9 - 225MB
cache: stl10 - 35MB
Date: stl11-189MB
Flash Back To Stock Rom
1) Odin (see below)
2) Driver to connect your samsung
mobile to PCDownload 3) USB Cable
4) Next Turbo S5570I with at least
70% of battery
5) Windows OS (XP recommended
but 7 works)
6) Firmware to be installed (see
below)
The version of ODIN which is used
on this device does not provide for
the use of OnePackage, and then
need to have the separate files.
How to get the files that are used
for the flash?
There are windows and linux,
windows or only with the second
method.
There are 2 methods of installation
and the third method to unbrick
(see the bottom of the guide).
Method 1
Download the version of Odin 1.84
(with associated files) to be used:
DownloadDownload the firmware fileDownload and pull them out of
windows
INSTALLATION
1.Open ODIN PIT and choose the
file (the one in the file so you have
to Odin
remove the Windows Desktop)
2. Click on pda.tar PDA and select
the file, click on the file and choose
PHONE phone.tar
3. Put the device in Download Mode
(Hold Vol Down + Home + Power) and
connect to the PC via the USB cable
(check the box posts you will see
the word "Added")
4.Press the START button
5.Wait up to 5 minutes, after which
will show PASS (do not touch
anything until it comes out the word
PASS!)
6.The phone will reboot itself
7.After that will output the word
PASS disconnects the cell from the
PC
METHOD 2
Download the version of Odin 1.84
(with associated files) to be usedDownload
Download the original firmware
(other than the first linkDownload
A developer has created a simple
application called Odinatrix!
This application successfully
decompressor the file(Winzip, 7-Zip,
Winrar, etc..
How to use?
1) Download it fromAttachment
2) Extract the folder on your DesktopODINATRIX
3) Extract the file and take
S5570IDDLA1_S5570IODDLA1_INU.zip S5570IDDLA1_S5570iODDLA1_S5570IDDLA1_HOME.
Tar.md5 and copy to folder Odintrix
4) Run the file "runme.bat" in the
folder Odintrix, after almost half an
hour in the folder you get the
output file:
*
CSC_S5570IXILB2_S5570iITVLB2_S5570IXXLB3_HOME.tar
*
MODEM_S5570IXILB2_S5570iITVLB2_S5570IXXLB3_HOME.t
ar
*
PDA_S5570IXILB2_S5570iITVLB2_S5570IXXLB3_HOME.tar
INSTALLATION
5) Start Odin
6) Enter the 3 files. Tar in Odin:
* Included in PDA PDA_xxxx.tar
* Included in the PHONE MODEM_
xxxx.tar
* Included in CSC CSC_xxxxx.tar
7) PIT and / or BOOT files are not
required - Leave the fields blank!
8) Leave as is everything else!
9) Put the device in Download Mode
(Hold Vol Down + Home + Power) and
connect to the PC via the USB cable
(check the box posts you will see
the word "Added")
10) Press the START button
11) Wait up to 5 minutes, after
which will show PASS (do not touch
anything until it comes out the word
PASS!)
12) The phone will reboot itself
13) After the output will be written
PASS disconnects the cell from the
PC
Bootloop ?
wipe data/factory data reset
[color=Root after flashing on stock rom[color=red]Download in Attachment[/color]
Copy the file to the Memory Card
Restart the device in recovery mode
(Hold Vol Up + Home + Power) Apply update from SD Card
Choose ZIP from SD Card (choose the root zip/file
Select YES, install update
Reboot system now
Install the ClockworkMod (Recovery)
Download in Attachment
How to Install?
It 'must have obtained root permission
Copy the file to the Memory Card
Restart the device in recovery mode
(Hold Vol Up + Home + Power)
Apply Update from SD Card
Choose ZIP from SD Card
Select YES, install update
Reboot System now
Samsung Galaxy Mini GT-S5570i
Firmwares
------------
DISCLAIMER:
------------
YOU HEREBY ACKNOWLEDGE BY
USING THE SOFTWARES INCLUDED
ON THIS SITE THAT I'M NOT LIABLE
FOR ANY DAMAGE OR BE HELD
RESPONSIBLE IN ANY WAY, WHETHER
EXPLICIT OR IMPLIED, IF YOU BRICK
OR TURN YOUR PHONE INTO A
USELESS PAPERWEIGHT. YOU ARE
USING THE SOFTWARES AT YOUR
OWN RISK.
If you're in another region, you
can try this firmware, it has
support for the following
languages:
Gingerbread 2.3.6
TIMLB1ITALY TIM
ITALY TIM
[url= http://hotfile.com/dl/153945172/d60fdc6/S5570IBGLB1_XECLA2_Spain_Android_2.3.6.zip.html]XECLA2SPAIN
ODDINDIA
ODDLD2INUINDIA
OJPLC2ARABIC
ARABIC
ITVLB2ITALY
WINLB2ITALY WIND
ITVLB2ITALY
OXEKK1RUSSIA
OXXKL3RUSSIA
CRGKL1CROATIA
ORRKK1CROATIA
OXXKL3XEZ CZECH
XSK SLOVAKIA
[url= http://hotfile.com/dl/155322252/7e5fe60/S5570IXXLD6_OXXLD4_XEZ_Czech_Android_2.3.6.zip.html]OXXLD4XEZ CZECH
OXXLD4XSX SLOVAKIA
CHNCHINA
SPACE
Tanks a lot, bro.And well explained.
Zilem said:
Tanks a lot, bro.And well explained.
Click to expand...
Click to collapse
welcome ..
any patch to working power buton.room it"s perfect.power buton it"s broken,click power buton and phone restart,maybe working any flash file for wake up with home buton thanks.
pancepaki said:
any patch to working power buton.room it"s perfect.power buton it"s broken,click power buton and phone restart,maybe working any flash file for wake up with home buton thanks.
Click to expand...
Click to collapse
Flash this Latest italy stock rom
http://forum.xda-developers.com/showthread.php?t=2661361
new firmware out there
thebiggboss180 said:
new firmware out there
View attachment 2737114
Click to expand...
Click to collapse
i saw that yesterday while i was also finding GS3 new firmware , you guys can download it and split it to 3 packages (splitfus <--- i dont know if i spelled it right or Odinatrix
akosicarlo said:
OXEKK1RUSSIA
OXXKL3RUSSIA
Click to expand...
Click to collapse
In Russia we call them S5570IXXKL2 and S5570IXXKL4, OXEKK1 and OXXKL3 - version CSC..
And links do not work, try on PC and phone..
thebiggboss180 said:
new firmware out there
View attachment 2737114
Click to expand...
Click to collapse
link please
blackaxeV1.2225 said:
link please
Click to expand...
Click to collapse
Now upload 3 file version..
I was downloading it
Sent from my GT-S5570i using XDA Free mobile app
---------- Post added at 11:28 AM ---------- Previous post was at 11:18 AM ----------
Hi guys did you have kies please give me the dl link pls
Sent from my GT-S5570i using XDA Free mobile app
blackaxeV1.2225 said:
I was downloading it
Click to expand...
Click to collapse
S5570IXXND1? Okay, to someone else will come in handy: link.. DropBox Link
Information:
Country: Czech Republic
Version: Android 2.3.6
Changelist: 1254568
Build date: Tue, 08 Apr 2014 05:36:30 +0000
Product Code: XEZ
PDA: S5570IXXND1
CSC: S5570IOXXNC1
MODEM: S5570IXXND1
Cut to three parts using Odinatrix
Screens about phone and languages: http://imgur.com/a/dvsqe
Gisha 7 said:
S5570IXXND1? Okay, to someone else will come in handy: link..
Information:
Country: Czech Republic
Version: Android 2.3.6
Changelist: 1254568
Build date: Tue, 08 Apr 2014 05:36:30 +0000
Product Code: XEZ
PDA: S5570IXXND1
CSC: S5570IOXXNC1
MODEM: S5570IXXND1
Cut to three parts using Odinatrix
Screens about phone and languages: http://imgur.com/a/dvsqe
Click to expand...
Click to collapse
I need kies for s5570i
Sent from my GT-S5570i using XDA Free mobile app
blackaxeV1.2225 said:
I need kies for s5570i
Click to expand...
Click to collapse
I do not use Kies..
If you want latest stock - flash stock that I posted in Odin v1.84/1.85/1.87.
By the way on picture: S5570 with android 2.2 froyo..
Im really sorry guys
i feel so useless being an OP on this thread cuz i can't even Compile or Update this Thread with Latest 10 Firmware for our mini ...... Bandwidth is killing me
Anyways , If anyone who's free to get busy giving me Direct Download link of Top 10 Latest Firmware for our Little device so i can get this thread updated . Just tell me and ill give you guys on credit
blackaxeV1.2225 said:
I need kies for s5570i
Sent from my GT-S5570i using XDA Free mobile app
Click to expand...
Click to collapse
kies not needed ..use odin....with the link gisha gave above
blackaxeV1.2225 said:
I need kies for s5570i
Sent from my GT-S5570i using XDA Free mobile app
Click to expand...
Click to collapse
You don't need kies for that. The only one you need in the kies are the samsung usb drivers but there's a separate installer for that
other than they're correct
ronhyukie07 said:
You don't need kies for that. The only one you need in the kies are the samsung usb drivers but there's a separate installer for that
other than they're correct
Click to expand...
Click to collapse
You can find the drivers on my guidehere
use this
http://www.sammobile.com/firmwares/3/?download=28786
Related
Hi
I deleted some programmes on my rooted TAB
Cant recall exactly what
Now Market fails with message 'The application Market (process com.android.vending) has stopped '
I deleted the cache but still it wont work
Can I restore the tab to an earlier date?
Can I somehow restore missing files?
PLEASE HELP need basic instructions as no expert
zalanz said:
Hi
I deleted some programmes on my rooted TAB
Cant recall exactly what
Now Market fails with message 'The application Market (process com.android.vending) has stopped '
I deleted the cache but still it wont work
Can I restore the tab to an earlier date?
Can I somehow restore missing files?
PLEASE HELP need basic instructions as no expert
Click to expand...
Click to collapse
Hmm... if you knew exactly which apps you deleted, you might be able to find them in another ROM and just adb push them back to the tab.
Otherwise, at this point, I would suggest a re-stock (take the tab back to factory settings via re-flash).
Which tab do you have exactly, and what Android OS were you running? For example, I have a Galaxy Tab 7" P1000 GSM (T-Mobile) and I used to run Gingerbread (2.3.3)
thanks
mine is a Galaxy Tab 7" P1000 GSM (ORANGE) on Gingerbread (2.3.3)
I know I uninstalled z4root but honestly cant recall what else.
How easy is it to restore?
Not sure how I reflash it?
Hmm, I'm not too sure if you need root or not to do an adb push, but it's pretty much:
Download app to computer, plug tab to pc, open cmd and do adb push FILE.apk
You'd need android SDK though prior to that and platform tools.
As for re-stocking, you can either use Odin (samsung's phone/tab flashing tool) or Heimdall (open-source flashing tool). In any case though, Team Overcome made a nice guide for restocking that should work with Odin.
http://forum.xda-developers.com/showthread.php?t=1317384
In short, you want to have Samsung's drivers installed, reboot your tab and put it in download mode, download the files needed to re-stock from that thread, open Odin, enter the gt-p1000 pit for pit, GB-stock-safe-v5.tar for the pda, and a modem for modem, then start flashing
I also made a nice guide involving Heimdall re-stocking here: http://forum.xda-developers.com/showthread.php?t=1508703
wow
bit too complicated for me I am afraid.
I am grateful for your reply, but I could not do that.
Looks like my TAB is useless now
It's not really too hard I'd hate to see your tab useless though.
If you had some sort of instant messenging service, I could maybe guide you through the process
thanks but I do not use Instant messaging.
@yyalanyy on twitter is all, but doubt tht could help?
If you could email me any simple [and I mean simple] help to [email protected]ltrans.co.uk I would be very grateful.
I can make you a package zip that will pretty much only require you to install drivers and then run 1 file (I can give you a small walkthrough on how to setup the drivers in email)
It'll take me a little bit to upload it though (I would say 40mins :/). Otherwise, if someone else feels like offering some simple instructions, feel free to do so
That would be great
many many thanks
Actually, download this: http://www.rosanoscorner.com/p1000/downloads/GB-Stock-Safe-v5.zip
And i'll upload my batch file in a bit. You'll just have to extract some things though
---------- Post added at 12:35 AM ---------- Previous post was at 12:16 AM ----------
Here's a guide (it's a bit long, but the steps are really quick)
- You'll also want 7zip installed (WinRAR might also work if it can open .tar), it's a free program for unzipping archives
1. Download that .zip file above and unzip somewhere
2. Download my archive here and unzip somewhere: http://www.mediafire.com/?pdpy59z6bdej6wb
3. In my folder, there is a Drivers folder, go in it
4. Run SAMSUNG_USB_Driver_for_Mobile_Phones (if it says drivers are already installed, then close it)
5. Reboot tab into Download Mode (shut it off and unplug from charger/computer, hold Vol-Down button and power)
6. Plug tab into computer
7. Go to the Drivers folder in my folder and open zadig
8. Options > List All Devices
9. Select Samsung USB Composite Device
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
10. Hit Install Driver (accept any prompts you see about unsigned drivers)
11. If it's successful, close it
12. Unplug tab and plug it back into computer (on the same USB port)
13. Go to the folder you extracted GB-Stock-Safe-v5.zip at
14. Find the folder called JPZ Modem (for anyone else following this, use the modem of preference)
15. Go into it, take the modem.bin, put it into my folder (my folder with the .bat and heimdall stuff)
16. Go back to the GB stock folder
17. Open GB_Stock_Safe_v5.tar (7-zip should open this like an archive)
18. Drag every file in that .tar to my heimdall folder
19. Run flash.bat in my folder
20. Do not do anything with the tab until it's done
21. Once the tab is done, you should be in recovery. You have to (i think) use the volume buttons to scroll up and down in the menu, but you have to wipe data, and then reboot to system
22. Done
I'll be here if you need any help still
hi
i have followed your instructions. when I run the flash,bat a cmd window opens, tells me to press any key but nothing happens?
zalanz said:
hi
i have followed your instructions. when I run the flash,bat a cmd window opens, tells me to press any key but nothing happens?
Click to expand...
Click to collapse
Hmm, it should be starting Heimdall and starting a 1-2min flashing process. Not too sure why it wouldn't actually work though
Try running it again and then when it says press any key, Right-click anywhere in command prompt > select all, and then when everything is selected, press Enter. Then copy/paste that into a post here
C:\Users\alan acer\Desktop\helpsamsung\Re-stock (Heimdall)>heimdall flash --repa
rtition --primary-boot boot.bin --cache cache.rfs --dbdata dbdata.rfs --factoryf
s factoryfs.rfs --pit gt-p1000_mr.pit --modem modem.bin --param param.lfs --sec
ondary-boot Sbl.bin --kernel zImage
C:\Users\alan acer\Desktop\helpsamsung\Re-stock (Heimdall)>pause
Press any key to continue . . .
its approaching 1.00am here so I must get some sleep.
Thanks for your help
I will have another try tomorrow
Thanks you
Hmm, how many files are in your Heimdall folder and how big is the folder? I think you should have about 15 files in the folder total, equaling 391MB
Edit: Just saw your message about you heading to bed, night
think thats the problem.
After using 7zip on your download there are only 6 files totalling 28mb ?
Hi
Tried it again and it worked!
So pleased thank you for all of your help
Problem now is different as it is now NOT rooted.
and it seems very laggy now.
I have tried Z4 root and it fails
I have tried superone click and that fails at stage 6
Any ides?
Would it be best via ODIN?
Hmm, thought I hit reply earlier but guess not :/
Anyway, with Odin, the only thing that is different is that it automatically wipes data/factory reset and wipes internal SD instead of you having to manually do this. Generally, Odin is slower as well too, but it does work
As for Root, hmm, not too sure what can be done about this. I can't recall me actually rooting Gingerbread (maybe someone else can shed some light on this?) I always flashed a custom ROM right after I re-stock, and most (if not all) custom ROM's offer Root instantly
No worries. At least my tab is useable again now. I would once again like to thank you for the help and time that you have given to me.
Sent from my GT-P1000 using Tapatalk
zalanz said:
No worries. At least my tab is useable again now. I would once again like to thank you for the help and time that you have given to me.
Sent from my GT-P1000 using Tapatalk
Click to expand...
Click to collapse
No problem
Hello, I have a little problem after installing clockworkmod with tutorial inside this page http://forum.xda-developers.com/showthread.php?t=1774560 (can't post outside link)
Instructions:
First time flashing CyanogenMod 10 your device, or coming from another ROM?
1. Root the device and install ClockworkMod Recovery. Instructions are available here.
Code:
Installing the ClockworkMod Recovery
This guide applies to a Samsung Galaxy Tab (GSM) on the stock 2.3 release. If the Samsung Galaxy Tab (GSM) already has the ClockworkMod Recovery installed, skip this section.
Warning: Installing a custom recovery image on the Samsung Galaxy Tab (GSM) will void the warranty.
Download Technomancer's kernel with the ClockworkMod Recovery and the Heimdall Suite:
Technomancer's Kernel with the ClockworkMod Recovery 5: Download
md5: e67e61a27741069e43bf9f790bf35b10
Windows:
Heimdall Suite 1.3.2: Download
NOTE: The Heimdall Suite requires the Microsoft Visual C++ 2010 Redistributable Package installed on the computer, which can be downloaded here.
Ubuntu 32bit:
Heimdall Suite 1.3.2 Command-line Binary: Download
Ubuntu 64bit:
Heimdall Suite 1.3.1 Command-line Binary: Download
Mac OS X:
Heimdall Suite 1.3.2: Download
NOTE: The source code for the Heimdall Suite is available on Github.
Windows ONLY:
Power off the Samsung Galaxy Tab and connect the USB connector to the computer but not the Samsung Galaxy Tab.
Boot the Samsung Galaxy Tab into download mode by holding down Power and Volume Down while connecting the USB connector to it.
Run the included zadig.exe in the drivers folder of the Heimdall Suite.
From the menu, choose Options » List All Devices.
From the drop down, select Samsung USB Composite Device or Gadget Serial.
Click Install Driver.
NOTE: A prompt may appear warning that the installer is unable to verify the publisher of the driver. Ignore it and select "Install this driver anyway."
Heimdall can now be used safely on the Windows computer.
NOTE: For more information about the Heimdall Suite, please read the included README.txt.
Power off the Samsung Galaxy Tab and connect the USB connector to the computer but not the Samsung Galaxy Tab.
Boot the Samsung Galaxy Tab into download mode by holding down Power and Volume Down while connecting the USB connector to it.
Untar Technomancer's kernel into the Heimdall directory.
On the computer, open terminal and run the following command from the Heimdall directory:
heimdall flash --kernel zImage
A blue transfer bar will appear on the device showing the kernel being transferred. The device will reboot automatically.
The Samsung Galaxy Tab now has the ClockworkMod Recovery installed. Continue to the next section.
After reboot I'm stuck on Galaxy Tab Samsung screen. I can reach clockworkmod and download mode. Is there something to worry about or I can just continue installing cm10?(when i launch clockworkmod it displays a few comunicates
E:can't mount /cache/recovery/command
E:can't mount /cache/recovery/log
E:can't open/cache/recovery/log
E:can't mount /cache/recovery/last_log
E:can't open /cache/recovery/last_log
cmd log:
Microsoft Windows [Wersja 6.1.7600]
Copyright (c) 2009 Microsoft Corporation. Wszelkie prawa zastrzeżone.
C:\Users\Bardys>cd c:\Users\Bardys\Desktop\Galaxy Tab\heimdall-suite-1.3.2-win32
\Heimdall Suite
c:\Users\Bardys\Desktop\Galaxy Tab\heimdall-suite-1.3.2-win32\Heimdall Suite>hei
mdall flash --kernel zImage
Heimdall v1.3.2, Copyright (c) 2010-2012, Benjamin Dobell, Glass Echidna
http://www.glassechidna.com.au
This software is provided free of charge. Copying and redistribution is
encouraged.
If you appreciate this software and you would like to support future
development please consider donating:
http://www.glassechidna.com.au/donate/
Initialising connection...
Detecting device...
Claiming interface...
Setting up interface...
Checking if protocol is initialised...
Protocol is not initialised.
Initialising protocol...
Handshaking with Loke...
Beginning session...
Session begun with device of type: 0
Downloading device's PIT file...
PIT file download sucessful
Uploading KERNEL
100%
KERNEL upload successful
Ending session...
Rebooting device...
c:\Users\Bardys\Desktop\Galaxy Tab\heimdall-suite-1.3.2-win32\Heimdall Suite>
edit:1
Flashed clockworkmod on gingerbread previously updated via kies from froyo
Version of clockworkmod: 5.0.2.8
Any help much appreciated
For those come from non ICS MTD rom, such as yourself from froyo,
You need to flash cm10 twice.
First round installs new cwm and converts to mtd.
Second round the rom itself.
So, just boot to cwm again, and flash cm10 again.
Sent from my GT-P1000 using xda app-developers app
By flashed i mean i have flashed only recovery yet.
Oops. Yes, then you should flash.
Weird you can't go download mode.
Sent from my GT-P1000 using xda app-developers app
I can, i created this thread because my stock rom isn't working after install of recovery and im curious why and to know if im safe to begin install of cm10
edit1: I found something, that can be related http://forum.xda-developers.com/showthread.php?t=1841748
gogol1996:Well, the problem is that the bootloop occurs if the cwm i mentioned is flashed in the firmware of gb stock safe package. so i recommend against it
Maybe that is the case but what can I do now?
Well you saw my post there too.
I can't say enough.
Overcome method works 100% where cf root fails sometimes.
When you said you can't go to download mode, what actually showing.
Sent from my GT-P1000 using xda app-developers app
I can access download mode, I just can't boot stock rom
Bardys said:
I can access download mode, I just can't boot stock rom
Click to expand...
Click to collapse
then you must continue the installation
There is something else about I forgot, because I installed recovery when the battery was about 40%i didn't have to worry about this, but now because I was checking recovery and download mode it's about 20% I think. When I plug the charger it displays battery whith circle but its not showing the state of battery, is it charging or not and if not will it charge in download mode/recovery?. And because I can't boot stock rom I can't access internal sd, can I use external from my wildfire S to place cm10 rom file and install via recovery?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
not sure about the charging from recovery/download.
But you can always powered it all down and charge.
yes you can download using your other phone.
but make sure it is not corrupted (I prefer to download using PC if possible)
I want to download using PC and transfer it to wildfire s sd card. You mean I have to deplete the battery completely? It's little risky, because if I then wont be able to charge it it's over. The tab is off when i plug the charger.
not sure about that part. Probably just battery charging animation. Just leave it charging for a few hours then do your flashing.
You are not flashing the bootload (since you are not using Odin), so it is unlikely you can screw up the bootloader. So it should be always possible to revive should anything go wrong. Unless there is hardware issue to start with.
Ok, I'll do as you say (for charging battery is responsible bootloader or Rom?)
I am not a dev. But I remember that certain battery charging animation pictures are in kernel. One of the cm9 humberos kernel has broken battery picture briefly when plugged in.
Sent from my GT-I9300 using xda app-developers app
Ok, I want just to make sure, that the charging script isn't damaged because if yes, the tab is just depleting(screen doesn't go off while charging)
edit1: That what I get in recovery:
I tried also HumberOS http://www.humberos.com.br/2012/08/cm10-20120823.html ,the same result.
What was your tab running before this? What model is it. What does it say at the back. The assert function says you are not P1000.
Did you do the whole GB stock safe v5 + overcome kernel.
If not, you should. That should correct the detection.
The alternative is to unpack the rom and find the updater script deep in META-INF folder and remove the assert lines....
Sent from my GT-P1000 using xda app-developers app
Model: GT-P1000
I said I was on stock GB, I will try restocking.
Not any restocking.
You want overcome method.
Sent from my GT-P1000 using xda app-developers app
You mean, that I should do from Overcome site http://www.teamovercome.net/p1000/?page_id=17 point "Re-“Stocking” Yer System…" or "Installin’ The Overcome ROM…" ?(just want to make sure) and have I to have Kies installed before using Odin?
I see there is a lot of people who post in here who dont know how to Flash JVU before Custom Rom with ODIN
Either they get the Red wipe error in Recovery or just arent sure on how to use it, hope this helps you...
THE TOPICS HERE ARE GUIDES ON HOW TO FIX OR USE :
RED WIPE DBDATA ERROR
FLASH JVU 2.3.6 BEFORE CUSTOM ROM
MANUALLY INSTALL CWM
FEAMOD RECOVERY INSTALL
FIX INTERNAL STORAGE ON GT-I9000M
FAILED TO MOUNT SD CARD (E: FAILURE IN RED)
COMPUTER NOT CONNECTING TO PHONE VIA USB
UPDATE TO CYANOGENMOD 10.
AND LINKS TO WHAT YOU NEED ......
Click to expand...
Click to collapse
------------------------------------------------------------------------------------------------------------------------------------
Red wipe error is because the problem is with the dbdata!
Install THIS FILE in the PDA section with ODIN and dont touch anything else!
DBDATA.RFS DOWNLOAD : If you need it
Open ODIN
Click the PDA button and choose the dbdata.rfs.tar file you downloaded
Make sure Re-Partition is unchecked
Boot your SGS into DOWNLOAD MODE
To do this : Hold down the Home, Volume Down and the Power button
Connect your device to your computer with the usb cable when in Download Mode
If your device is connected Odin will recognise it
Click Start in Odin and wait
When the process is completed your device will restart
No more dbdata errors!...
------------------------------------------------------------------------------------------------------------------------------------
HOW TO GUIDE : TUTORIAL TO FLASH 2.3.6 JVU + ROOT BEFORE INSTALLING CUSTOM ROM
Samsung USB Drivers : DOWNLOAD MINE or LINK 1 : LINK 2
Needed to recognise Phone to your PC ... duh! :silly:
Reboot Computer once installed for changes to take effect :good:
Please do not attempt anything if you don’t know completely what it is.
If any damage occurs to you or your device, I will not be held liable ... you have been warned !!
If you arent sure ... just ask
FLASHING JVU ROM WITH ODIN v1.85
Why ODIN v1.85? ... I have not had any issues with it, plain and simple!
Use ODIN with PIT File
PIT File Incase you need it : DOWNLOAD
*Using PIT File just Tick Re-Partition and put PIT File in PIT ..simple!
ODIN 1.85
ODIN FILES HERE
Turn off your phone and put it in download mode by holding VOL DOWN+MENU+POWER
Do you get the Yellow Triangle?..If so continue..if not do it again...
VIDEO LINK : HOW TO GET INTO RECOVERY / DOWNLOAD MODE
Open ODIN and select 512 .PIT, and put in your files for : CSC, PDA, MODEM
*PIT File isnt always needed to do this only if you get the 3 Red errors*
Plug in Phone with USB Cable To Computer
In ID:COM it should go yellow and you should see ADDED in the message box
Check Re-Partition option and then Cleck PIT button to select: s1_odin_20100xxx.pit file.
Click PDA button and select : CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar
Click PHONE button and select: MODEM_I9000XXJVU_REV_00_CL1092175.tar
Click CSC button and select: GT-I9000-CSC-MULTI-OXAJVU.tar
When you have all the files needed in ODIN, say JVU Rom as thats what we are using here
Click Start let it Run
Once complete you will see S logo on phone (computer will make a few noises like connect/disconnecting
Unplug the Cable to the Phone
Power Off Phone
Go into Download mode so that we can now root the Phone
Then plug in Phone
Click Reset on ODIN then in PDA put in CF-Root Kernel File for JVU to be Rooted
CF-Root is in ODIN FILES or DOWNLOAD HERE
Then Click START.. should take just a few seconds ....
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Same again when you see S Logo on Phone unplug Cable
Close ODIN
Now, what I do now is go into :
Settings > SD Card and Storage > Unmount SD and Wipe that and then at the bottom Wipe Format USB Storage
Enable USB Debugging > Plug in Phone
Window should open up showing your phone Directory..
Copy over your ROM that you want
Shut Down Phone
Reboot into Recovery (Vol UP - Menu - Power)
Wipe the 4 things (probably know these... you should do)
Data / Factory Reset
Cache Partition
Go to Advanced > OK
Dalvik Cache
Battery Stats
Go Back > OK
To move Up or Down > Use the Left Side Volume Rocker Switches with Menu to OK Action
Install your Custom ROM from Zip Card that you want...
Reboot Phone when complete... DONE!
Please Check APN Settings.. for your area after you have done the following steps to give better signal
Sometimes Authentication Type is set to Default..try it at PAP and then Reboot Phone
As some ROMS APN settings are done manually for the user.. so be careful
Rom I am currently using : Blue SAUROM JWB
Hope this helps out a few people as there are quite a few posts opening up with the same problems or issues :good:
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Manually Install CWM (need to have Root in your phone)
Download This FILE and copy it over to /sdcard/
Power off and Boot into Recovery with 3 Button Combo
Select 'apply sdcard:update.zip' and Install (Do not Delete this file from SD Card)
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Deleting Cryption Meta Data Error : CWM6012-CM9-Recovery
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
IF YOU CANT GET INTO RECOVERY (only if CWM doesnt work)...
Start ODIN
Put your Phone into Download mode and connect it via USB
(Volume Down + Home and then Power)
Download FeaModRecovery : HERE
Choose PDA and use the Downloaded File and put it in there > START
Wait for process to complete....
Exit ODIN..
Start Recovery ....
Install .. Reboot....Done
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
IF YOU STILL RECIEVE THE : E: Failed to mount /sdcard
Try This :
Download This First SDFormatter (Windows)
1. Download "SDFormatter" from the link above
2. Install "SDFormatter"
3. Enable "USB Debugging Mode" from Developer Options in settings.
4. Connect your tablet to PC (USB).
5. Then, tap the "USB Strage Mode" to connect to PC.
6. Backup data on INTERNAL_SD card.
7. Run "SDFormatter".
8. Specify the drive letter of INTERNAL_SD in SDFormatter and click "(Option)" button.
9. "FORMAT TYPE" select "FULL OVERWRITE" and set "FORMAT SIZE ADJUSMENT" to "ON" and click "OK"
10. Now click "FORMAT" and wait for the procedure to complete. (Can take approximately 1 hour 40 minutes)
11. After format is completed you can recopy the backup files back onto the INTERNAL_SD
..or Try and Format SD card in your Computer
If none of the above works try this : Samsung Format Utility
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
FIX INTERNAL STORAGE ON GT-I9000M (/dev/block/mmcblk0 corrupted) : SEE THIS POST
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
COMPUTER NOT CONNECTING TO PHONE VIA USB
Windows
Remove all traces of KIES in Add/Remove.. never use KIES anyway...Reboot PC
Unplug any attached USB Devices to PC
Use Latest Samsung USB Drivers HERE and install.. Reboot System when Done
Go to Device Manager and scroll to the Bottom > Universal Serial Bus controllers
Expand all Items >
Now Uninstall one by one all the way down...
Reboot Computer when Done.
Plug in Phone... wait till it recognises Device.
Some people have also tried ...
Going into Download Mode, Connect Phone to USB.
System should install a Driver.. and voila!
Done.
DOWNLOAD THIS AND FOLLOW INSTRUCTIONS IF YOU NEED MORE HELP
Please Hit the Thanks Button if I helped you... :victory:
A.I.O Rescue & Recover : LINK
Android Solutions : LINK
Samsung Updates : HERE
Latest Official I9000 and I9000M Firmwares collection : LINK
Modems : LINK
Perka's File Stash : LINK
Z4ROOT APP : HERE
3 BUTTON COMBO FIX : HERE
SECRET CODES : HERE *Use at your own Risk!*
--------------------------------------------------------------------------------------------------------------------------------------------------------------
Procedure To Update Samsung Galaxy S With Cyanogenmod 10
Device must be running latest Gingerbread 2.3.6 with ROOT to begin .....
Remove KIES completely from Phone and reboot Computer then Install latest Samsung USB Drivers then Reboot Computer...
Ensure that your phone battery is at least 85 percent charged
Cyanogenmod 10 Download
Download Google Apps (Optional)
Connect your device to PC by using the cable.
Enable mass storage mode on it.
Now transfer / copy all the 2 files to your device’s internal SD card.
Ensure that you are not keeping it in deep directory.
Now disconnect the phone from computer.
You then need to enter into recovery mode.
To do so, switch off the device completely, press & hold Volume Up button + Home Button + Power key until recovery mode appears.
After entering into recovery mode, select “install zip from sdcard” & then “choose zip from sdcard“.
Navigate to the ROM file (which you’ve transferred earlier)
Select it & press on ‘Yes‘ to continue. ROM installation process will start.
Wait for the ROM to get installed.
After ROM gets successfully installed, your phone will land in the recovery mode again.
Now select wipe data/factory reset & wipe cache partition to wipe all the data & caches from the phone memory.
The same procedure you have to do for installation Google Apps. (Just don’t do the above step i.e, don’t wipe the data after installations of Gapps).
After installaing both things, now press back button to land in recovery mode.
Select reboot system now from the Recovery mode to Restart the phone.
Usually first boot of the phone takes some time after flashing of new ROM so be patient....
Done!
Issues if you have any :
LOW STORAGE NOTIFICATION : HERE or See this LINK
If the above doesnt help TRY THIS APP
NO MOBILE DATA :
Toggle Flight mode ON/OFF
IMEI Issue :
Flash a stock version of Android for your device: GB 2.3.6 (JVU, or other) that will restore your IMEI
Then you can backup the /EFS folder.
NO 3G AVAILABLE :
The CSC you used is most likely not intended for your area.
This means that the broadband provider settings are not included and
need to be configured manually.
Go to : Settings->Wireless and Networks->Mobile Networks->Access Point Names, press the settings-button and select "New APN"
Galaxy S i9000 / 9001 Disassembly & Assembly
Will add more links when I can ...
Fantastic...
After struggling like an armless lumberjack for what seems like a millenium - I can now relax
Major thanx are flying your way for this epic tutorial
Snowhiter said:
Fantastic...
After struggling like an armless lumberjack for what seems like a millenium - I can now relax
Major thanx are flying your way for this epic tutorial
Click to expand...
Click to collapse
Your most welcome!
Will add more when i get the time...:fingers-crossed:
Added more useful Links.. should be everything you need
HI,
thank you for this huge How to!
I have big trouble to update my Device.
It is not possible to get in the download mode. I tried SDFormatter, it crashes every time i connect SI, Samsungs Ex. HDD Formater runs but no effects on the Phone. Odin cant flash anything (maybe of course of download modus).
What do you recommend?
Sys:
WIN XP Pro SP3, Samsung Driver, Kies
Samsung SI, Android 2.3, Vodafone (Germany) Branding, No Simlock, SIM insert (E-Puls, Provider), No Ex SD Card, original Samsung USB-Cable
What are you trying to update to?
Using the Format tool try with USB Debugging ON
>
Uninstall Kies and reboot machine
Use my HOW TO Files ...
Install Samsung USB Drivers to install then reboot computer again..
Open ODIN and Check Re-Partition and put in PIT File
Make sure all 3 are ticked...
Also put in PDA / Modem / CSC press start when phone is connected via Download MODE
Press start....
Then just follow the rest to Root it...
Let me know if this helps
If you are wanting to go to CM 10 or JB Kies is no use anyway...no one uses KIES anymore
Thanks a lot. I pressed volume +... That was my fault.
Now runs CM 10.1 Nighlty with Helly Bean!
Tnak you
Finished moving GT-i9000 to CM-10 after using your steps.
Thank you.
Just have to solve camera app problem now
grA$ said:
Finished moving GT-i9000 to CM-10 after using your steps.
Thank you.
Just have to solve camera app problem now
Click to expand...
Click to collapse
Glad it helped
** Updated :victory:
New links added ... should cover everything!
This should be more than enough for anyone with problems with there S i9000 Phones
Re: [HOW TO GUIDE] ★ Flashing Rom with JVU before Custom ROM + EXTRAS ★
Thanks for the amazingly helpful thread. I had spent amazing amounts of time looking for a JVU bootloader an could not find it. Now i don't need to as your GB odin files fulfilled all my needs.
Now to test out whether your section on drivers will solve my issues of connecting post GB ROMd phone to my computer.
Sent from my GT-I9000 using xda app-developers app
Your welcome, if you dont need Kies in your computer get rid of it ....
Reboot computer afterwards then Install the Samsung USB Drivers and reboot PC again to take affect....
If Phone doesnt recognise follow the Tutorial on the link if USB not Recognised
Random thought .......Life is so good!
High WAF Wireless Inductive Charging Mod Step by Step Guide
Ok i am a little confused with your guide so decided to ask a few questions
i have read your guide down to after odin and this is where i got stuck
i downloaded odin and the odin.tar file on the page what confused me was this - Open ODIN and select 512 .PIT, and put in your files for : CSC, PDA, MODEM
i could not find the underlined files for these. also this confused me too
Check Re-Partition option and then Cleck PIT button to select: s1_odin_20100xxx.pit file. (make sure its on or off?)
Click PDA button and select : CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar (i only have the odin tar in post)
Click PHONE button and select: MODEM_I9000XXJVU_REV_00_CL1092175.tar (there wasnt anything there when i clicked it)
Click CSC button and select: GT-I9000-CSC-MULTI-OXAJVU.tar (there wasnt anything there when i clicked it)
any help would be nice before i continue
mazoshi said:
I downloaded odin and the odin.tar file on the page what confused me was this - Open ODIN and select 512 .PIT, and put in your files for : CSC, PDA, MODEM
i could not find the underlined files for these. also this confused me too
Check Re-Partition option and then Cleck PIT button to select: s1_odin_20100xxx.pit file. (make sure its on or off?)
Click PDA button and select : CODE_I9000XXJVU_CL851880_REV03_user_low_ship.tar (i only have the odin tar in post)
Click PHONE button and select: MODEM_I9000XXJVU_REV_00_CL1092175.tar (there wasnt anything there when i clicked it)
Click CSC button and select: GT-I9000-CSC-MULTI-OXAJVU.tar (there wasnt anything there when i clicked it)
any help would be nice before i continue
Click to expand...
Click to collapse
Re-Partition > ON
If you downloaded the ODIN Files all these are included in the files PDA / MODEM / CSC
HERE
What Rom are you coming from etc...
im useing what was on the phone and my phone is upto date so not sure
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Before going into details let's have a look on some key features of Asus Zenfone 4 A450CG::
4.5" Capacitive Touchscreen
1.2 GHz Intel Atom processor
8.0 MP camera with PixelMaster
1GB RAM
Android 4.4 KitKat (Not out of box)
1,750 mAh Lithium battery
Full hardware specifications :
DISPLAY:
- 4.5" Capacitive Touchscreen
- IPS FWVGA display resolution (800x480)
- Corninng Gorilla glass 3 protection
- 10 fingers supported touch input
CPU: Intel Atom Z2520 1.2 GHz
RAM: 1 GB LPDDR2 RAM
STORAGE:
- 8 GB internal memory
- Expandable upto 64 GB using an SD card
CAMERA:
- Rear 8 Mega-Pixel, F2.0 Aperture, PixelMaster
- 0.3 MP front facing camera
H/W and WIRELESS NETWORKING INTERFACE:
- v2.0 High Speed USB
- Bluetooth 4.0
- 802.11b/g/n wi-fi with WLAN support and WiFi direct support
- 3.5mm audio jack
- Power lock button and the volume rocker buttons
NETWORK FREQUENCY BAND and DATA SPEED:
- EDGE/GPRS/GSM: 850/900/1800/1900
- UMTS: 850/900/1900/2100
BATTERY: 1750 mAh Lithium battery
======================================================================================
=== I ASSUME THAT YOU ALREADY KNOW THE RISK OF DOING THIS ===
=== AND ===
=== I'M NOT RESPONSIBLE FOR THE DAMAGE OF YOUR PHONE ===
=======================================================================================
-------------------------------------------------------------------------------------------------------------------
TO ROOT YOUR ASUS A450CG
-------------------------------------------------------------------------------------------------------------------
Download the resources above and install Intel Android Driver View attachment intelandroiddrvsetup1.1.5.zip
Turn Off your Asus Zenfone 4.5 A450CG
Go to Droidboot Mode (Hold Power button + Volume up)
Connnect Asus Zenfone 4.5 A450CG to the PC
Download Root file "RootZenfone450.zip" View attachment 2950905
Unzip RootZenfone450.zip to a folder and open command window (by pressing Shift + Right Click)
In CMD window Type : fastboot flash update rootzen450.zip
Wait until OK then reboot.
View attachment 2950913
After restarting looking SuperUser application, if the application already exists Asus Zenfone A450CG means you have successfully rooted.
-------------------------------------------------------------------------------------------------------------------
FIX BOOTLOOP || STRUCK ON BOOT || STOCK FIRMWARE
-------------------------------------------------------------------------------------------------------------------
Instructions on how to dump files system.img.gz YOUR STOCK ROM
How to dump the rom file on zenfone 450 system.img.gz
Requirements:
PHONE has root
PC have installed the drivers on
Method:
Open the cmd to type the following commands, View attachment stockflash.zip
Note:: To dump the file system it TAKES quite long so do not remove phone neither press any key ,
let's
turn your phone offline!
turn screen off to 30 minutes
open the start.bat this will open CMD window
connect your phone
turn on USB DEbugging
and type this to CMD WINDOW
adb shell
su
(To the above tel root report agrees offline)
mount o remount, rw / system
dd if = / dev / block / mmcblk0p9 | gzip> /Removable/MicroSD/system.img.gz
complete dump file in memory card
USE THIS DUMP TO FIX THE BOOTLOOP ETC
********************************************************************************************************************************
GUIDE TO FLASH STOCK ROM DURING BOOT LOOP********************************************************************************************************************************
First:
Download system.img.gz file if you dont have Backup
The v4.1.1
SYSTEM IMG
BOOT IMG View attachment 2950957
The v4.2.3
SYSTEM IMG
BOOT IMG View attachment boot4.2.3.zip
CHOOSE ANY OF THE AVAILABLE (( SYSTEM IMG+BOOT IMG ))
Copy System.img.gz+boot.img to the folder "stockflash"( extracted from downloaded stockflash.zip)View attachment stockflash.zip
BOOT TO DROIDBOOT MODE
(power and volume +)
Plug the cable connected to your computer
OPEN THE START.BAT(CMD WINDOW)
type the command
fastboot erase cache
fastboot erase userdata
fastboot erase system
after that
fastboot reboot-bootloader (( reboot to droidboot itself ))
now
type:
fastboot flash boot boot.img
(What's boot.img downloaded above++ both firmware have different boot.img dont mix up )
now turn off your antivirus
and type
fastboot flash system system.img.gz
FLASHING WILL TAKE ABOUT 20-30 MIN
dont disturb PC it will HANG
after its DONE
reboot the
OK okay
Note after first reboot boot to droidboot menu and do a factory reset
if my post helped you then please HIT THANKS BUTTON
ANY PROBLEM/SUGGESTION PLEASE COMMENT
A billion and more thanx to u
're gently, when I tried to root my device ,it was successfully done.but after a minute or two ,it shut down and stuff not turn on , I found that nth device war bricked , and those helped Me too retrieve my device from the bricked situation.
ASUS Zenfone 4 A450CG
It would be helpful if you can provide a tutorial to install custom recovery (CWM or TWRP).. is it possible to install custom recovery in our devices...
Thank you so much! And I have some notice about this that when I finished flashing the rom, there is a root status stuck on the device too!
Sent from my ASUS_T00Q using Tapatalk
For CWM you have to give a try by YourSelf...i Dont own the device now..i can provide the files for CWM recovery but it may brick your phone...
Sent from my Primo F2 using XDA Free mobile app
Hai
hello, do you have firmware before 4.1.1? i wanna downgrade to version 3.x.x
anjargr said:
hello, do you have firmware before 4.1.1? i wanna downgrade to version 3.x.x
Click to expand...
Click to collapse
Not Released until now...
Sent From..old Rusty Typewriter
ss429842 said:
Not Released until now...
Sent From..old Rusty Typewriter
Click to expand...
Click to collapse
emhh i have trouble, I touched the reading mode in the settings even force stop, when update to latest version firmware 4.3.2, can you help me? sorru for my bad english
anjargr said:
emhh i have trouble, I touched the reading mode in the settings even force stop, when update to latest version firmware 4.3.2, can you help me? sorru for my bad english
Click to expand...
Click to collapse
Use the Boot.img for the same version which ever System version you aee installing......for example if you are going to flash 4.1.1 version then use boot img 4.1.1 ....or else you will find yourself in Bootloop/ restart/ hanging problems
Sent From..old Rusty Typewriter
Nice work there, I wish we see some development soon about our device and custom recoveries too.
Hi. Do you have CWM recovery which will be compatible for our device. If you have. Provide the file. I'm ready to give a try
Virus0044 said:
Hi. Do you have CWM recovery which will be compatible for our device. If you have. Provide the file. I'm ready to give a try
Click to expand...
Click to collapse
Will must provide..
Sent From..old Rusty Typewriter
----Do it With Your Own Risk----
----Do it With Your Own Risk----
Install with computer/laptop:
1. Download CWM Recovery for Zenfone
(https://db.tt/ReEJHU15)
2. Install ADB (Downloadhttps://db.tt/6YZ8HXu8 )
3. Unzip and copy to the same folder
4. Use RootExpoler access to the file
system rename the r ecovery-from-
recovery-from-boot.p boot.bak or move
somewhere out memory cards
5. Run the " install.bat" file pending reboot
is OK
So you've finished installing CWM
Recovery For Zenfone
How to Install CWM Recovery
1. Turn off your Zenfone
2. Press the power + Volume -down
3. Wait a moment it will enter Recovery
The method is basically for zenfone 5 but it should work for 4.5 ..
Try at your own risk...dont blame me
Sent From..old Rusty Typewriter
ASUS Zenfone 4 A450CG
ss429842 said:
For CWM you have to give a try by YourSelf...i Dont own the device now..i can provide the files for CWM recovery but it may brick your phone...
Sent from my Primo F2 using XDA Free mobile app
Click to expand...
Click to collapse
Can you provide the files and throw in some instructions too... please.. oops.. sorry dint see the last post.. seems u already did!! great!! will try!!!
Thank for your guide. But I got a problem after I flash stock rom 4.1.1. I can't upgrade to 4.3.4 again. My droidboot version is 4.3.4 but system version is 4.1.1
Could you build a system file 4.3.4 ? Thank you very much! And sorry for my bad english
Help me!!!
Help make the system boot version V4.3.4 for WW (thanks). :crying: :fingers-crossed:
virus1412 said:
Thank for your guide. But I got a problem after I flash stock rom 4.1.1. I can't upgrade to 4.3.4 again. My droidboot version is 4.3.4 but system version is 4.1.1
Could you build a system file 4.3.4 ? Thank you very much! And sorry for my bad english
Click to expand...
Click to collapse
Sorry but ,I Dont Own the Device NoW . so cant make a backup.
Sent From..old Rusty Typewriter
4.3.4?? I m still on 4.2.1, is that an new update?
Jexbox said:
4.3.4?? I m still on 4.2.1, is that an new update?
Click to expand...
Click to collapse
Yes, this update just released on october 15.
Sent from my ASUS_T00Q using Tapatalk
Well i haven't got that yet can anyone post a system dump
Firstly, thanks to a lot of help from @Nmc_alves® @adfree @[email protected] and @technoproz (Link here). As well, most, if not all, of the files are provided by these guys & a big shoutout to them!
Purpose of this post is to put the information all into one for SM-R845 and other things that I've come across that may help others too.
Converting from R845U to R845F [using sample scenario: R845U XAR (US) to R845F ITV (Italy)]
Prepare by downloading the following files:
Wifi NetOdin - (Click here - uploaded by Adfree)
COMBINATION-FT55_R845USQU1ATL2_clean_v1.zip (Click here - uploaded by kebez)
R845FXXU1CTJ5_Tizen_4File_CSC (OXA).zip (Click here - uploaded by kebez)
SDB tools (Click here - uploaded by Adfree)
Prepare Watch
1. Switch to Connect Wifi, always on (just in case),
2. Software -> Software Version. Press multiple times to turn on Developer Mode.
3. Turn on Debugging Mode.
4. Hold Back & Power button until you see the Reboot Mode. Use power button to scroll to Download (Wireless), and hold power button to select.
5. In wireless download mode, double press the power button to change the mode to act as a hotspot.
PC
6. Open NetOdin
7. On PC, connect Wifi to SM-R845. NetOdin should turn green.
8. Under AP, place the combination firmware. Once completed, give it time for the watch to set up.
Watch
9. Go to Connections, Wifi, and select Always On. Connect to same wifi network as your PC.
10. Note down your IP Address: 192.168.Y.Z
11. Reboot your watch to make sure it is connected to same wifi network.
PC
12. Unzip SDB tools and run version based on your PC.
13. Go to Data/Tools and open ansicon.exe
14. Type the following to pull files:
a. sdb connect 192.168.Y.Zb. sdb root onc. sdb pull /csa/csc/csc-active-customer.infd. sdb pull /csa/imei/prodcode.dat15. You should see 2 files in the same folder: csc-active-customer & prodcode. Open these 2 files using notepad, make the following edits and save:
a. In the csc-active-customer file, change XAR to ITVb. In the prodcode file, change SM-R845UZKAXAR to SM-R845FZSAITV16. Type the following to push files back in:
a. sdb push csc-active-customer.inf /csa/csc/b. sdb push prodcode.dat /csa/imei/
Watch
17. Go to Reboot Mode again. Select Download (Wireless). Double press to go to AP mode.
PC
18. Open NetOdin.
19. Connect Wifi to watch (SM-R845F-xxx). NetOdin will turn green once again.
20. Extract the original firmware R845FXXU1CTJ5_Tizen_4File_CSC (OXA).zip. Files are labelled so place into BL, AP, CSC accordingly. CP is the modem (I placed added it in for completeness so that the entire 4 sets are of the same firmware but will still work even if you do not flash it) Double check, and then flash away.
Q&A
1. How do you figure out what firmware to choose for your region?
Use the link as a starting reference
https://doc.samsungmobile.com/SM-R845F/ITV/doc.html
a. use either R845U or R845F
b. type in your region code.
If the combination is correct, you will see build information and firmware pertaining to your intended region.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
2. So now that I know which firmware to target, is it 100% certain that by flashing that firmware, I will be able to switch to that region?
Not true.
In the case of TGY, there was build information provided (https://doc.samsungmobile.com/SM-R845F/TGY/doc.html).
I would assume going thru all the steps above with TGY and flashing the upload firmware CTJ5 would yield my intended goal. It was not true. You need to actually download the firmware itself, use .7z to open the csc.img (see below).
What this means is that although TGY has a firmware version CTJ5, the uploaded package provided does not have that region!! Download and inspect the file yourself. If you did proceed with the combination/sdb/flash, you just won't have the region you want no matter what you typed in for the .inf & .dat files.
3. Now that I've flashed from R845U to R845F, I want to go back to R845U. Which combination file do I use?
I used the R845F combination file provided by @Nmc_alves and failed at the very end (not sure why). Scared the crap out of me as the Samsung logo appeared and the software was stuck. Don't panic and reboot back to wireless download mode. I used the original R845U combination file and was successful. I cannot explain why but what I did that worked.
4. I have CSC Region A installed and I want to switch to CSC Region B, do I need to go thru the combination file or can I just start from the steps involving SDB pull/push?
I went through the beginning with the combination file. Of course, if your firmware has both Region A & B, then all you need to do is do a reset (eg. CTJ5, going from Italy to Sweden).
5. Now that I've flashed R845F CTJ5 firmware, why am I not able to update it?
Good question. I don't know. I went thru from R845U BTK2 ->R845F CTJ (SWE) -> R45F BTH4 (XSA) by flashing only BL, AP, CSC and wasn't able to push for FOTA. I even used NetOdin and flashed in CP for BTH4 (XSA) and still wasn't able to push. My mistake could have been flashing from CTJ5 to BTH4 using NetOdin directly.
I reflashed the combination file, sdb command, picked the intended firmware and flashed BL, AP, CSC and CP. Got the FOTA notification and updating to DUC2 as we speak.
6. Can you manually update firmware? Also, rather than waiting for FOTA update, can I flash to a higher firmware version.
You can. Have to make sure it is available and double check the CSC file for the region just to be safe.
Reserve
Hi, I have a watch 3 R855U but can't find COMBINATION file, can you give me this file. Thank you so much, brother
I haven't seen anyone posted it.
Easy firmware has it but payment required.
Link
icecool217 said:
I haven't seen anyone posted it.
Easy firmware has it but payment required.
Link
Click to expand...
Click to collapse
thanks for your reply. I have paid and downloaded it, but when the step 6 is finished, the device reboots continuously, it seems it's not customized
?
Can you give more details?
A
Maybe you took old Firmware and now you are in Security Trap... because f&5ing Rollback Prevention blabla...
Latest leak I can see is:
COMBINATION-FT55_R855USQU1AUA3.tar.md5
B
In Firmware packages for LTE is additional folder with additional file... this makes trouble in old neOdin...
netOdin is meanwile 4 or 5 years old...
And only 1 Version leaked...
Code:
meta-data -->crap folder
1.mf ------->crap file
This is why I remove this folder from TAR files...
Best Regards
Can someone confirm if changing CSC to Italy will enable ecg, blood pressure and samsung pay?
TienDinh said:
thanks for your reply. I have paid and downloaded it, but when the step 6 is finished, the device reboots continuously, it seems it's not customized
Click to expand...
Click to collapse
Please share in details exactly what you did and what files you used. If you have Netodin results, you may wish to post the details of the flash.
As @adfree mentioned regarding the meta-data files, saw another post mentioning so not sure if relevant to yours that's causing the issue -> Link
jmatic said:
Can someone confirm if changing CSC to Italy will enable ecg, blood pressure and samsung pay?
Click to expand...
Click to collapse
Already done and confirmed working.
Link
icecool217 said:
Please share in details exactly what you did and what files you used. If you have Netodin results, you may wish to post the details of the flash.
As @adfree mentioned regarding the meta-data files, saw another post mentioning so not sure if relevant to yours that's causing the issue -> Link
Click to expand...
Click to collapse
here bro: https://drive.google.com/file/d/1Uqxey-funDJCz4bGKWER71RUPVHaGeYy/view?usp=sharing
Can you customize it for me? thanks you so much
ATL2 could be outdated/obsolete...
Better... maybe less risk:
COMBINATION-FT55_R855USQU1AUA3.tar
Best Regards
TienDinh said:
here bro: https://drive.google.com/file/d/1Uqxey-funDJCz4bGKWER71RUPVHaGeYy/view?usp=sharing
Can you customize it for me? thanks you so much
Click to expand...
Click to collapse
Before proceeding, refer to @adfree message as ATL2 could be outdated/obsolete
COMBINATION-FT55_R855USQU1ATL2(meta-removed).tar download
adfree said:
ATL2 could be outdated/obsolete...
Better... maybe less risk:
COMBINATION-FT55_R855USQU1AUA3.tar
Best Regards
Click to expand...
Click to collapse
thanks you so much bro
icecool217 said:
Before proceeding, refer to @adfree message as ATL2 could be outdated/obsolete
COMBINATION-FT55_R855USQU1ATL2(meta-removed).tar download
Click to expand...
Click to collapse
thanks you bro, Can I safely use this file, right?
@TienDinh
Can you check Firmware Version on your SM-R855?
Easiest way with most infos is to enter this code like you would call someone...
*#1234#
Write your infos here...
Best Regards
adfree said:
@TienDinh
Can you check Firmware Version on your SM-R855?
Easiest way with most infos is to enter this code like you would call someone...
*#1234#
Write your infos here...
Best Regards
Click to expand...
Click to collapse
Hi bro, my watch is currently stuck with a logo and can't access the main screen
TienDinh said:
thanks you bro, Can I safely use this file, right?
Click to expand...
Click to collapse
I basically took the file you provided.
Used .7z to extract all the files and folders within
Deleted Meta-data folder (with 1.mf file contained within)
Repackaged everything back to .tar
You can download and compare the file and your original file to double-confirm that only meta-data folder was removed.
TienDinh said:
Hi bro, my watch is currently stuck with a logo and can't access the main screen
Click to expand...
Click to collapse
If your watch came with the box (and have yet to update the firmware), the firmware should be listed on the back of the box as well.
Hi bro, my watch is currently stuck with a logo and can't access the main screen
Click to expand...
Click to collapse
Maybe helpfull... for you... not me. Because I have this problem not...
Give maybe more details...
A
You remember your Firmware Version?
So it is possible to identify date...
B
What you did to reach this status of bricked Watch...
And how much bricked?
You are sure Download WiFi is still alive?
C
You have access to latest LEAK:
COMBINATION-FT55_R855USQU1AUA3.tar
Then better use this...
Best Regards