i have a motorola droid and it is rooted.i flashed a new rom and then i flashed sprecovery,i let it run its course and i disconnected the phone.when the phone turns on it starts up and then a red light comes on and my phone says please connect charger.it keeps saying android process is not responding and then the phone shuts itself off.ive tried to boot it into recovery mode and do a restore,it keeps giving me an error that says nandroid exited with status 20 and its also not reading my sd card.can somebody tell me whats happened and if it can be fixed???please and thank you
Well, seems as if you need to reflash or restore because of bad flash. If you try flashing again make sure you wipe data and cache. As far as not reading sdcard I have same problem not sure why but when I'm in recovery and I choose install zip which I used clockworkmod recovery, if it fails then it reboots automatically after couple seconds not sure if this happens with sprecovery. After sdcard mount fail it shuts down and reboots so before it reboots I pull the battery and wait a minute or two before trying again. It may take me 3 to 4 times of doing this but eventually it will mount sdcard in recovery. I recommend keep trying till it allows you to apply recovery file and then flash to either clockworkmod or sprecovery which ever one you not using and then flash back to the one you want. I'd also recommend try if after all this you flash rom again and same thing happens redownload it and try again. Good luck.
Sent from Droid using, Sapphire v1.0.0/ 928Droid Black Glass 2.2 Theme/ Sholes 1.0 Ghz 7 Slot Kernel.
Please install Advanced Task Manager and from the setting use what ever setting that might suite you.
For me i use the following setting:
Auto Kill Level --> Safe
Auto Kill Frequecny --> Every One Hour
Security Level --> Meduim
With the above setting, i didn't face any performance problem and reduced reboot frequency (General Problem in the Android).
Feel free to ask any question and I will be ready for you
fadimck said:
Please install Advanced Task Manager and from the setting use what ever setting that might suite you.
For me i use the following setting:
Auto Kill Level --> Safe
Auto Kill Frequecny --> Every One Hour
Security Level --> Meduim
With the above setting, i didn't face any performance problem and reduced reboot frequency (General Problem in the Android).
Feel free to ask any question and I will be ready for you
Click to expand...
Click to collapse
Please note, that there have been wide reports of people having issues with various task killer apps consuming excessive amounts of battery life when used on a Droid with Froyo.
Please install Advanced Task Manager and from the setting use what ever setting that might suite you.
For me i use the following setting:
[*]Auto Kill Level --> Safe
[*]Auto Kill Frequecny --> Every One Hour
[*]Security Level --> Meduim
With the above setting, i didn't face any performance problem and reduced reboot frequency (General Problem in the Android).
Feel free to ask any question and I will be ready for you
Click to expand...
Click to collapse
Please note, that there have been wide reports of people having issues with various task killer apps consuming excessive amounts of battery life when used on a Droid with Froyo.
Click to expand...
Click to collapse
Okay, I didn't know this info as I've Milestone with stock OS 2.1
Sent from my Milestone using XDA App
Attention, new stable rom for our legends!
From a Spanish cheff, SuperFroyo MVZ Legend 8
The thread is in Spanish, but you can download the rom from the link "Descarga" in red.
The thread: http://www.movilzona.es/foro/topic2567.html
Thanks to superatmel for his hard work, we finally have an alternative with Froyo in our machines.
EDIT: The rom is working FINE finally right now. Download and test!!
Enjoy this rom from Superatmel
EDIT2: Translation of the first post of the SuperFroyo ROM:
SuperFroyo MVZ 8 for HTC Legend, MovilZona edition
It´s installed from the recovery, as every time you install a ROM. Don't worry if takes a long time to get the first splash. It´s absolutely normal because it executes the config files in the first boot.
Added by manudas: It really reboots twice, the first time for the overlay filesystem, for having read/write access to the system partition.
You must have the Legend rooted. If you don´t know how to do, please search in this forum before asking.
I strongly recommend a full formatting to the SDCARD with three partitions EXT3 512MB / LinuxSwap 64MB and the rest in FAT32. You can do it from the recovery, but remember to save your data before (pics, music, etc…). This is because some directories are created in the sdcard (Android) in which records data I found to negatively affect the rom. PROVEN!
-------------------
WARNING!
This rom autoinstalls itself, and also restarts twice after installation. Ie, reconfigures itself.
WIPE is recommend before the installation, because it has many changes. After installing the rom leave it alone for at least 4 minutes, not touching the screen, because this is the time it takes to finish of installing everything. Then you can setup the rom, but I recommend that you skip the google config, pressing skip button, and once in the launcher you can configure the rom as you like. This is because otherwise the phone will autoconnect to the market, and begin to automatically download all the applications you had installed. Al this can saturate the terminal because it does everything at once. Besides, if the phone connects to the market, background image that you had prior to the rom flashing will be there again, and then you will ask how is possible that after a wipe the bottom appears as you had before.
If you follow my instructions you will do a clean install. Then you should enter the market and install a free application to refresh the applications you have installed in the terminal and to see if everything went well you should go into "Downloads" and see if appears at least an update of SupSetup I'll post this afternoon to check .
Very attentive to you who do restorations of any kind against the rom cause you can have problems. (I mean backups, including their own SupSetup least in the application section). Special attention to restore configuration data of any kind. Under doubt, the best it´s not doing it.
Remember that the installation is at your own risk.
- Added Apps2sd in SupSetup. Now even allows the deactivation of this without having to WIPE. NEW! Do not be alarmed if you reboot, read the posts !!!!! (Better don´t use the applications move feature of Froyo)
Don´t activate Apps2sd without at least once you have restarted
Improvements in this version.
All versions are the same for all terminals
In 8
- SupSetup with integration to Legend
- Implementation of the base for HTC Legend
- Bug fixed Chamber
- HTC Legend Custom Kernel (2.6.29.6 reissued)
- Deactivated perflock for changing CPU frequencies (Only Legend)
- Implemented Swap Legend, not Compcache
- New edition of Framework for all bases (Nexus, Magic, Dream, Legend, Galaxy S)
- Preparation for FM (But not yet available)
In 6.6.4
- On base Froyo FRG83 2.2.1
- Kernel 2.6.35.6 (Nexus One, Magic & Dream)
- Digital retouching (the Chinese muiu)
- More stable Camara
- Google Apps updates
- Etc. ..
In 6.6.2
- New Gmail upgradeable
- New upgradeable Street View
- New way of setting up the internal processes with better results
- New SupSetup V12 14.06
- Edited the rill for a better and stable 3G HSDPA coverage
- Various internal improvements
In 6.6
- New management of the post installation Rom
- New way of SupSetup for disabling applications of the rom (Attention!! Disable is not uninstall)
- New very optimized kernel and removed processes that do not use the Nexus
- New SupSetup V12 v14.00
- New Launcher Pro if activated from the SupSetup configured for higher performance.
- Appear new SupSetup's with more applications to disable!!
- Now install themselves the voices for the GPS
- And more internal improvements for a brutal stability. That if it´s installed with a generous WIPE!
- Adding the Control of energy, I recommend activating the cells that are in the last captures for battery consumption settings, because for example when you turn on wifi automatically pass to 2g for lower battery consumption or you change the data will change also to 2g, or if the wifi is enabled then will activate the sync automatically, etc ...
In 6.4
-Added new option in SupSetup with the direct integration against the system (Optimize the system)
- New setup for the Launcher Pro: to activate it from the SupSetup, go to applications! Important if the Launcher Pro is enabled, for activating the future updates of the market you have to execute the option Optimize system!
- New Shazam
- Rescheduled framework for the implementation of the new option of SupSetup
- Kernel settings
- Adding the Control of energy, I recommend activating the cells that are in the last catch for battery consumption settings.
- Etc ...
In 6.2
- Fix Shazam
- Recompiled the framework to eliminate obsolete processes
- A small graphic touch
- Added black and white bar from the jrosmetamorh. (You must enter the program and select the folder jrosmetamorh / SuperFroyoBNegra or SuperFroyoBBlanca, wait to finish installing and reboot).
- Set some xml framework
- New icon of the battery.
- Various internal improvements
- This rom is very stable.
In 6.1
- All Cyano improvements
- Fix for flash player to install without Wipe (Nexus only)
- Improved 3D Gallery
- New ADWLauncher 1.1.5
- SupSetup V12 12.94
- Updated all apps
- Added icon headphones
- New kernel 2.6.34.5
- And as always own improvements
In 6.0
- Fixed a bug in the CPU frequency
- Fixed issue with FlashPlayer, if it does not work, apply "the force be with you" from the SupSetup, and wait to restart. (Solo Nexus)
- Fixed problem with Speech Sinthesis.
- Edited the battery again to display up to 100% load
- Revert SoundRecorder
- Added Series for Android
- Optimized Kernel for lower consumption. (Removed unused drivers)
- And besides of my optimizations, all from Cyanogen too
In 4.4
- Added restart in normal mode, recovery and bootloader
- Enabled again hsdpa
- Fixed bug in the battery icon
- New Wallpaper.apk
- New sounds and notifications in addition to integrating the lock & unlock from Iphone
- Many of internal improvements in the libraries
- Camera with manual focus touching the screen.
- Added Launcher Pro activating it from the SupSetup (applications menu)
- Added File Explorer activating it from the SupSetup (applications menu)
- ADWLauncher updated to version 1.1.4 (thanks AnderWeb)
General
- New option in the SupSetup Applications
- Added Development (Disabled from SupSetup)
- Added STK sim provider (Disabled from SupSetup)
- Added File Explorer from the SupSetup (Disabled from SupSetup)
- Terminal (Available from SupSetup)
- Added news and weather
- Implemented Flash Player 10.1 (only Nexus)
- Added Google Chrome to Phone. Allows you to launch pages from pc to mobile with one click, after installing the plugin on Google Chrome on your pc.
- Now you can customize the toolbars notifications from the Spare Parts.
- New application for viewing videos.
- Control the music in the lockscreen activated from the Spare Parts
- Many and funny improvements in Spare Parts for the control of the rom.
- You can modify all the colors of the rom including notification bar (text notifications, time and date)
- Now SupSetup applies directly the changing of CPU frequency
- Modified the management of "the force be with you", with better results of suffering sporadic FC's.
- Fixed the problem of always-on Bluetooth from SupSetup
- Implemented LinuxSwap and CompCache, but warning, you can only enable one of the two. If you enable one the other will be disabled automatically (Thanks Tole)
- And many small modifications to control the system.
- Optimized all the apk's png
- Take a look at the new Spare Parts integrated settings.
- Improved management of root
- New Market Management
- Now enabling APNs from SupSetup automatically applies
- Development is disabled from SupSetup
- New options in the Spare Parts that can even choose which applications are installed if not activated Apps2sd (better do not use)
- Wake Unlock & Wake up
- Sound Recorder can record conversations
- Updated Spanish translations
- Added Speech Synthesis (To the voices of the GPS)
- Added provider SIM STK
- Now you can activate and deactivate the JIT from the Spare Parts
- Spare Parts and SupSetup integrated into the rom settings
- Bug fixed contacts and translations
- Redesign of the images of the framework
Applications
- Audio Manager
- Google Apps integrated default
- Maps with GPS 4.5.0
- New Gmail
- Shazam
- AndroidVNC
- Ebuddy
- Facebook
- SupSetup V12
- Twitter
- Wireless Manager
- Wifi status
@superatmel is great, very great. Can't wait.
Sent from my Legend using XDA App
Can I ask why I would want this over say the Cyanogen Mod froyo ROM?
not hating, just asking.
Also is it in English?
I think that is multilingual. This rom includes optimizations from cyanogen, as its author says, and many other of their own. You should try it and if you like it you stay, if not you can restore the previous. Furthermore, this will activate the FM radio in future versions.
wow great news! Finaly something fresh on legend scene! More chefs should work on froyo roms
Good!
thank you I'll try this one as soon as it's available.
PS: GPS does not work in Cyanogen for me, so I hope it's fixed in this one.
hoping that rom is multi language that avail english!
Anyway I think it would not be difficult to add some language support in case that have not english
manudas said:
Furthermore, this will activate the FM radio in future versions.
Click to expand...
Click to collapse
I laughed a lot on this one.
Not that it's impossible and I really wish the devs good luck on btips and that proprietary mess HTC created.
ali ba said:
I laughed a lot on this one.
Not that it's impossible and I really wish the devs good luck on btips and that proprietary mess HTC created.
Click to expand...
Click to collapse
I laugh because he laughed.
Rom is on servers, ready to download!
its huge 85mb... now downloading... after download flashing!!!
How is it?
I can not wait to try it. I'll download it now. Someone who has tried can give us the first impressions and tell us if in addition to Spanish it has English?
Well tried it but all i got was boot loop. It starts but at enter pin the phone reboots.
Same here.
Boot loops on pin code entering.
Did u wipe before flashing? I wanted to flash this rom to, but my SD card started to f*** with me AGAIN. Now trying to backup data and format it, if it would help.
Yes, I did.
same here wiped everything, but no go.
Wiped twice, reboots at the first screen (touch the android logo)...
Google Translate doesn't help much:
This rom installs itself alone, that is completely reconfigures.
WIPE recommend because it has many changes, after installing the rom to let her leave without touching recovery 4 minutes or more exactly because of that time will finish installing everything. Then you can already configure but I recommend you salteis the account settings to skip giving google and once in the launcher and set podreis rom to your liking. This is because otherwise the phone will Autoconnect the market and begin to automatically download all the applications you had installed and it saturates the terminal because it does hit, besides putting the background image that you had prior to the rom and then you ask me that as it is possible that if I install the rom to wipe the bottom appears to me that I had before. In this way you will do a clean install. Then you enter the market and instalais a free application to refresh anyone that you have installed in the terminal and to know that everything went well when you go into shock must appear at least an update of SupSetup I'll post this afternoon to check .
Very attentive to you to do restorations of any kind against the rom or program that you can have problems. (I mean backups, including their own SupSetup least in the section on applications), special attention to restore configuration data of any kind. Under the best not to doubt.
Remember that the installation is at your own risk.
- Added Apps2sd in SupSetup now even allows the deactivation of this without having to WIPE. NEW! Do not be alarmed if you reboot, read the posters !!!!! (Better not use the applications move Froyo)
Apps2sd not activate without at least once you have restarted
HELP
I've got a problem with my Nook Color (BNRV200)
Tired of searching for a thread that tells you what to do when you need to install, fix a problem, need a recovery, etc. I have compiled a number of links to various threads by developers and others that answer questions that get asked a lot. This post is intended to give a site that will make finding these answers easier than a regular search. It will have a list of threads and posts with various helps, have a topical list of problems and sites which address those topics, links to common sites and app needed to get what both Noob and seasoned members need to work with and on Nook Colors.
You choose to make changes, flash ROMs, etc. it is your choice. You assume all responsibility for what ever happens. I list these links because I know they have helped and work for me as well as many others. If you need help with a particular problem addressed in these links, ask on those threads.
If you use information in any of these links make sure to click on the thanks button both here and in those links. If you want to write a thank you note also, that to is fine, but does not add to the "Thanks" counter. These people have worked hard for free that we can have greater enjoyment and fun with our tablets. Most get nothing for their time and effort so "thanking them" is their greatest return and the least the rest of us can do in appreciation. Credit and kudos are given by Authors Names in Post #2
By Topic(A)
Add Network speed to Status Bar. Post#3
Android.process.media force close or crash Click here Also make sure all Google apps are updated, defrost frozen ones, update in play, refreeze (Mine was Gmail) (Thanks bowguy)
(B)
Boot Loop Problems (2)
Bootable CWM Recovery SD (v5.5.0.4 and now v6.0.1.2) (1)
(C)
Change "Status Bar" or "Navigation bar" colors or heights (for two rows of status info). Post#3
Change perceived DPI, rotation behavior, fullscreen, permissions on a per app basis Post#3
(D)
Dual Boot Nook (12)
(F)
Faster bootup
To get faster bootup you can disable the boot animation and save about 30 seconds from boot up time by adding "debug.sf.nobootanimation=1" to the build property file in the /system folder. This is a pain though if you keep up with the nightlies regularly like I do. I got tired of editing the file for every update or reversion if there was a problem with the newer nightly. So I created a script that goes into the Userinit.d folder that checks build.prop on every boot and adds the line if needed without any further intervention. The first boot after installing a new nightly will have the boot animation but no more till the next install when the process will repeat all automatically. Download the AutoNoBootAnimationScript.zip in attached files below, unzip, follow the included instructions and enjoy.
Faster SD card access. Instructions bottom of Post#4
Freeze/Disable applications (1)
(G)
Google Play says, "This app is not available for your device"
Get Xposed Framework in Post#3, download "PlayStore Fixes", set Fake density 240, Check No Restrictions Patch. Clear Google Play Store data, reboot enjoy.
(H)
Home button / icon stopped working, defrost / enable android Keyguard
How can I make my ROM run smoother, have more free memory or have longer battery life. Post#4
How to play flash video on Android 4.4 Kitkat in Dolphin Browser (14)
How to do a Logcat (13)
(I)
I wiped, erased, formated my /ROM (#2) partition (2)
Installing CM11 and get Status error 7 or other problems - Must use CWM 6.0.4.7+ or TWRP 2.6.3.0 (Download below)
Installing new CM11 and latest Gapps and no Google Play. Problem /system is too small.
The Prefered way to fresh install latest nightlies: If you do a conventional (no repartition) install using the smaller 01/05 Gapps and install the other Goople apps through Google play. They install into the /data directory instead of the /system. You can do this also with Gmail, Sound search (ears), Google TTS and Hangouts.
Alternate experimental adventurous way. There are two .zips available that will repartition your Nook and give you more /system space and /Data space.
Dweatons mod of Leapinlarswork, Repart.zip, is here and will yield 1.1Gb /System, 2Gb /Data, and 3.6Gb /Media.
Mine is here and will yield 1.1Gb /System, 4.5Gb /Data, and 1Gb /Media. You must get and use a reformat 5,6,7,8.zip after the running the repartition.zip for dweatons get Leapinlar's here. For mine get it here. the difference is for his you must install with CWM before 6.0.3.6, mine works with 6.0.4.8. Reverts to B&N Stock /system are available here.
Installing CM on EMMC CM11 (8), CM10.2 (9), CM7 or CM10 (6)
Installing CM on SD (3)
(M)
Make Play Store show All apps in listings Post#3
Modifying partition sizes original (5) Modified for CM11 and CWM 6.0.4.8 (15)
More SD card storage Use a 64 Gig SD Micro. Instructions bottom of Post#4
(N)
Nook won't boot (7)
(P)
Put Play Store link in App info window Post#3
(R)
Recovery boot loops (1)
Repairing partitions, blank screens and cannot flash new roms (2)
Restore Nook Color to Stock, (4)
Running Netflix app in CM 10 and 11 (11)
(S)
Screen touch sensitivity a little off. Try Nook Screen Recalibrate in Google Play
SD Card install tips Leapinlar's Tips post #2
Stock Nook Color Roms Leapinlars (1.4.3), Dizzy Dens (1.4.1)
(V)
Video Flicker in CM11 Crackle, Hulu and other video sites and apps, update to CM11 nightly 4/22+ or (10)
Volume / Sound to low. Try Speaker Boost in Google Play. Caution:
Mine works great @ 50% boost. Be very careful above 40%, go slowly and safely. If you want to rename the DSPmanager goto post #6. If you have CM 10.2+ (4.2.1) you must do the renaming since the DSP version since then throttles back the sound levels.
(Y)
YouTube updated and asked for update for Google Play Services but Google play has no update. Get Version 4.2.43 here: (11) (At bottom of attached files) Latest (4/20/2015) New update on Youtube and / or Google Play problems. Solution here: http://forum.xda-developers.com/showpost.php?p=60241045&postcount=54
(W)
Where can I get:Gapps http://wiki.cyanogenmod.org/w/Gapps
Latest Nightlies http://download.cyanogenmod.org/?device=encore&type=nightly
Recoveries (download in attached files below)
Stable versions http://download.cyanogenmod.org/?device=encore&type=stable
Older releases of CM 10 or CM11 http://techerrata.com/browse/cm/encore/nightly List of Authors of Post
To whom credits and thanks are due!
See Post (#2)
If you know of other Help, Info, etc sites post a reply I'll check it out and include it in the lists above. Even if the post are not on Nook Color forum, If it worked for you on your Nook, post a reply with your Rom version and I will check it out and consider adding it to this list.
Recoveries The recoveries I have are listed below and can be downloaded in the attached files box. The MD5 sum files are in the MD5 sums for recoveries zip. Download it, un-zip it, and check with the approriate recovery. These are for the Nook Color (BNRV200)
CWM Recoveries3.2.0.1 - Good for CM7 Eyeballer or nemith
5.5.0.4 - Good for CM7 thru CM10.2 Racks
6.0.1.2 - Good for CM7 thru CM10.2 - LeapinLar
6.0.5.0 - Must have for CM11 5-16+ Nightlies eMMC & SDCard installs - polymath257
6.0.5.1 - Latest Available - rjwil1086TWRP Recoveries2.3.1.0 - From TWRP Site
2.4.1.0 - Eyeballer
2.6.3.0 - Must have for CM11 thru 5-15 nightly (use 2.4.1.0 for pre CM11) - Eyeballer
2.8.3.0 - Must have for CM11 for 5-16+ nightlies - rjwil1086(nba#+5)
[INFO][HELP][FIXES][HOW TO] Collection of Help - Pt2
By Author of Post
Dean Gibson
Repartitioning the NC to 1-5 Gb, 2-4Gb and 5-1 Gb: (5) http://forum.xda-developers.com/showthread.php?t=1094371
Eyeballers
Install CM7 or CM10 + Recovery to EMMC: (6) http://forum.xda-developers.com/showthread.php?t=1030227&highlight=install+cm7+to+nook+color
Leapinar
Tips: (1) http://forum.xda-developers.com/showthread.php?p=25354258#post25354258
EMMC Repair: (2) http://forum.xda-developers.com/showthread.php?p=28457126#post28457126
Nook Color Installation Guide for CM7/CM9/CM10/CM10.1/CM10.2/CM11 on SD: (3) http://forum.xda-developers.com/showthread.php?p=32921666#post32921666
nismopc
Running current Crackle TV 4.0.3 on CM11 Nightlies: (10) http://forum.xda-developers.com/showthread.php?t=2634964
Nootered
Restore to Stock: (4) http://forum.xda-developers.com/showthread.php?t=931720&highlight=fix+boot
pastordl
Running current Netflix app in CM 10 and 11: (11) http://forum.xda-developers.com/showthread.php?p=44626173#post44626173
Repartion and reformating zips for CM11 and CWM 6.0.4.8: (15) http://forum.xda-developers.com/showpost.php?p=54401912&postcount=4177 (From Dean Gibson's work, also Leapinlars and Dweaton)
paxChristos
[Tutorial] How To Logcat (13) http://forum.xda-developers.com/showthread.php?t=1726238
RileyGrant
Dummies Guide to Fixing 'My Nook Won't Boot' (7) http://forum.xda-developers.com/showthread.php?t=949699&highlight=boot+zip
Steven676
CyanogenMod 11 Nightly Builds for Nook Color: [Read first three posts]: (8) [FONT="]http://forum.xda-developers.com/showthread.php?t=2629337[/FONT]
surviveland
[Guide][Flash]How to play flash video on Android 4.4 Kitkat - xda-developers (14) http://forum.xda-developers.com/showthread.php?t=2548001
Tausaur
Dual Boot (12) http://forum.xda-developers.com/showthread.php?t=1275859
Tdm
CWM 6.0.4.7 Touch Recovery Ramdisk (http://forum.xda-developers.com/showpost.php?p=51446977&postcount=19015) http://forum.xda-developers.com/showpost.php?p=51446977&postcount=190
Customize Rom or Apps without being a developer - Xposed Framework
Customize Rom or Apps without being a developer - Xposed Framework
From Rovo89's thread
In this thread, I'm presenting a framework which gives you the possibility to modify your ROM - without modifying any APK (developers) or flashing (users)!
Click to expand...
Click to collapse
Get Xposed Framework and install instructions Click on "click to show content" box
For the framework:
Download the Xposed Installer APK and install it
Launch the Xposed Installer, go to the "Framework" section and click on "Install/Update"
Reboot
Done!l
You can verify this by starting the Xposed Installer again. If app_process jumped back to an older version (or none at all), you probably have a ROM with S-On or similar, which reverts any changes to /system after a reboot. Then you can try to flash this file: http://forum.xda-developers.com/show...postcount=2308
For any modules you want to install:
Download <module>.apk and install it
Launch the Xposed Installer and go to the "Modules" section (you will also get there if you click on the notification warning you that the module is not enabled yet)
Enable the module by checking the checkbox
Reboot
Done!
For information & help with Xposed Framework go to Rovo89's thread.
Once you have installed the Xposed Framework you can get many of the modules under the Download tab in the framework app.
There are also a large number of modules at this thread made for module developers to list their work. If the Modules indicate they are made for a specific phone or tablet they may not work on others. If you try and it does not do what it says it will do, contact the module maker, not rovo89, unless it is his module, ie: "Make Play store show all apps" or just un-install the module. No guarantees they will help. Some only have one tablet and only develop for what they have.
A Short list of some of the things you can do using Xposed Framework and modules.
These do all work with CM11 current nightlies and CM 10.2 last nightly, 1/19/14
For more info on Modules listed install Xposed Framework and click on Download tab
Change color of status bar / notification bar. Xposed Framework - X Blast tools. Plus lot more. By femblack.
Network Speed Indicator - by fatminmin. With 123 below the up down speed can be shown in two readable rows. ** This will not work with CM10.2 Stable with the 3.0.8 Kernel or the updated hack fix kernel
Play Store link in app info - by qwerty12 - Does what the title says
App settings - by Tungstwenty & Rovo89 - What it is: This is an Xposed module that allows changing generic settings on a per-app basis. "Generic settings" means settings that are global to all applications, such as: perceived DPI, rotation behavior, fullscreen, etc..
Play Store Fixes - Rovo89 - Make play store show all apps
Enable SwiftKey predictions in more places - by qwerty12 - Email address website and filter list fields.
123 Dimension Editor. - by Hamzahrmalik - Change various UI dimensions: Status bar height, Navigation bar height and others. I doubled the height of my status bar and shrunk my navigation bar.
Cool Tool: - by Deviant Studio Software - Monitor various system info in floating window or in Status Bar. I have time, day, date, Free Memory and Battery Temp in two rows of my status bar.
Status bar volume. - by Niko001 - Move the volume bar over the status bar.
I do like things my way. That is what Android is noted for.
This Module "Workaround for Netflix on CM10/CM10.1" works on most any CM10 thru 10.2 Rom.
From Kaepernick's post.
"Well, thanks to Entropy512's help, I was able to modify his Xposed hack to work on CM10 (based on Android 4.1) and CM10.1 (based on Android 4.2) for the Incredible. Using the newest Netflix app and it's working well without issue.
Click to expand...
Click to collapse
Get it here.
*** Make the Xposed Framework persist through a CM ROM update with script "90-xposedpersist.sh" (in the 90-xposedpersist.zip), put the ".sh" file in the /system/addon.d/ folder. Available here See Post #4 there for specifics here***
Image 1. Cyan status bar & navigation bar, network speed indicator & X blast options.
Image 2. Play Store button in app info.
Image 3. App Settings screen.
Image 4. Home screen with dual line expanded status bar, Cool tool info and Net work speed.
Run CM10 & 11 smoother and get more free memory
Tips to help CM10 and CM11 run smoother, less laggy, etc.,
and have more free memory on your Nook Color
and maybe even a little longer battery life.
These are a collection of tips that have been collected from various post in XDA, personal sharing with others, and as a result of my own desire to try to improve things where I can. I have tried everything listed here and each adds a little to smoothness(s), free memory(f) or battery(b) life. My CM11 flashed Nook runs quite smoothly, with free memory at desktop running from 110 to 160 Mb and six to eight hours of battery life depending on type of constant use. This is on a nearly three year old tablet. I have partitions set to 5Gb data and 1Gb media. All apps are in the tablet. I also have a 32Gb Sdcard. I also have over 220 apps including system apps. I use my tablet from 6-8 hours or more a day.
Unless noted all apps mentioned are available through Google Play. I recommend the apps, etc., because they work for me. I get nothing out of it except the joy of helping others. Like everything try at your own risk. This includes app I have on my Nooks. If you have other programs you can try adjusting them as I have and see how it helps, or not. Trying and finding out what does and doesn't work is half the fun.
Free and simple
On all CM10 and CM11: (s) Try lowering your maximum clock speed to 1000, or even 800mhz in System, Performance Processor, Maximum CPU frequency. Many have reported improved smoothness at slower speeds. Faster can run ahead of itself and actually make things jittery. Make sure to check Set on boot to retain settings.
CM11: Use 5/17+ nightly.
On all: System Settings ( some may only apply to CM10 or 11 List:
Wifi, advanced,Uncheck Network Notification (b)
Keep Wifi on during Sleep, only when plugged in (b)
Scanning always available, uncheck (b)
Wifi Optimization, checked (b)Sound,Set quiet hours (your sleep time)(b)
Touch sounds, screen lock sound, volume adjustment sound and Charging Sounds, Enable, all unchecked (b)DisplaySleep (set time for max time you want screen to stay on before going to sleep, shorter time saves more battery)(b)Developer Options,Kill app back button, checked, (Allows you to kill kill app by long pressing back button)(b)Performance,CPU governor, (Lower on list will give faster response but use more battery, Default is "ondemand". Try the others and stick with what suits you the best.) Make sure to check Set on boot to retain settings.If you haven't activated the "Developer Options list":In "About Tablet, Build Number, tap ten times till it states "Developer Options turn on."
AdFree: (b) Available on Slideme.com Stops adds in browsers and most all App with add banners. Saves time by not downloading the adds.
On All: ((f,b) Freeze / Disable unused (unusable) apps in System.(b,s,f)
Don't delete them since any ROM update you install will replace them, freezing / disabling them will last through an update. The stock App manager allows you to disable most of these. Titanium Backup and Rom Toolbox Pro can freeze more but do cost, though I think they are well worth the price for what they deliver. There are some free "App freezer" programs available. I've only tried Chef's App Freezer, check the ratings and comments.Android Keyboard (ASOP) - I use Swiftkey (lite is available)
Camera - (No camera in Nook, no need of file)
Com.android.smspush. No phone text.
Gmail and / or Email and Email Services (if you use another E-mail client, ie:K9)
File Manager ( if you uses another ie Root Exporer (Speedsoft) or Root Browser (Jrummy))
Google search - Definately slo-o-ows things down
Key Chain - if you don't use lock screen
Mobile Data and Mobile Network Configuration - No phone, no need
One time Init - only used on first install once
Picasa uploader - If you don't use Picasa
Print Spooler - If you don't use it.
Sound Recorder - No Microphone, no need
Sound Search for Google Play - If you don't use it
Talk back - If you don't use or need it.
Trebuchet - If you use another Launcher.
Voice+ - No Microphone or phone, no need.
If you use a different clock than stock, calendar etc you can freeze / disable the stock version. Example: I use Dejaoffice to link with Outlook on my PC so I freeze Calendar storage, calendar, and calendar sync.
Change app permissions: (f,b) (for apps that run at startup and then stay in memory even when you not running them.)
I use App settings, it requires Xposed Framework to run but once set up does it's thing in startup, changes permissions, and closes. To get the Xposed Framework go here.
The most common causes of this problem are the following permissions: receive boot completed, vibrate, and wake lock. Not all apps can have these turned of. App settings has the ability to launch the program from is menu. Try turning off a permission, save, menu (launch). If it works great, if not go back and turn that permission back on.
The following is a list of Apps I changed permissions on and which permissions I disabled to keep them from persisting / sticking in memory:Advanced Task Manager: receive boot completed, and wake lock.
Alarm Clock Extreme: read phone state, receive boot completed, vibrate, and wake lock.
BusyBox Installer: receive boot completed, and wake lock.
CPU Master Pro: receive boot completed.
Crackle: receive boot completed, vibrate.
DejaOffice: vibrate.
Elixer: vibrate, and wake lock.
Evernote: receive boot completed, and wake lock.
Google Play Services: receive boot completed, and wake lock.
Kyo-Tux Aeon HD: vibrate.
News and Weather: receive boot completed, and wake lock.
Nook: receive boot completed, vibrate, and wake lock.
Pandora: receive boot completed.
RoboForm: receive boot completed
ROM Manager: receive boot completed, and wake lock.
The Weather Channel: receive boot completed, vibrate.
Titanium Backup: receive boot completed, vibrate.
Winamp: vibrate.
YouTube: receive boot completed, vibrate.
Advanced Task Manager: (b,f,s) Put the widget in dock, set your ignore list in app. One press and all unwanted apps go bye-bye.
My Ignore List:
Adfree, Elixer Widget, Alarm Clock Extreme, K-9 mail, Nova Launcher, Swiftkey, Speaker Boost, Pie Pro, Earthquakes, AFWall+, Clipper+, DejaOffice, Tasker, 360 Security.
Not so Simple but worth the time, still free
Replace DSPManager with Speaker Boost: (f,b) Get more volume and save EMMC memory.(DSPManager 18Mg - Speaker Boost 1.7 Mg=16.3Mg saved) Get more info here.
Replace Trebuchet with Nova Launcher: (s) does more, has more adjustments. (Does take more memory but pays back in smoothness)
LagFix (fstrim) Free. (s) Use two to three times a week. (s,b)
Use Elixer widget to replace other widgets: (f,b) and save Memory 45 meg (for Battery widget, Wifi state and stats widget, free memory and CPU stats) - 12 Meg for Elixer = 33 Emmc memory saved.
Rom toolbox lite: Settings: (f,b,s) (some of these may need Pro)
Under performance.Settings, Main Preferences, Boot Delay, 40 seconds.
Task Manager, Tap on Task Manager on top left of screen.You can change the Minfree memory settings, with CM10 I found strict to work the best. So far with CM 11 custom settings of 30 FA, 40 VA, 65 SS, 75 HA, 90 CP, and 100 EA setting works well.) I set them then save them into custom settings). Make sure to update to 5/17 nightly.
Start up killer, add Elixer, Google play services, The Weather Channel, and YouTube. (keep them out of active (service) memory or minimize there active size.)
Ignore List. 360 security (or your antivirus app), AdFree, AFWall+, Android system, Clipper+, Earthquakes, Elixer Widget, K-9 Mail, Mobile Data, Nova Launcher, Pie Pro, Rom Toolbox Pro, Speaker Boost, System UI, Tasker.SD Boost. You can change the size of the cache to both internal and external SDcard. I find with my class 4 Sandisk SDcard a setting of 4096KB works best. A benchmark is available to test your settings. If you have a faster card ie: Class 10 you can try larger cache sizes and save as custom.
Not Free but worth it (IMHO)
Upgrade to Nova launcher Prime:
In Nova Settings: (s)
Look and Feel, Scroll and Animation speeds (faster than light) (s)
New Apps - check Auto Add Short cuts, (make sure to turn off auto add in Google Play.)
Labs - Check the following, Big Grid size options, Widget Image Async List, Widget Image Cache, Restore Widgets Faster. (s)
Upgrade to Rom Toolbox Pro, LagFix (fstrim) Premium (scheduling trims): Get more bells and whistles and help support the developers.
Upgrade to 32 or 64Gb Class 10 SD card - Buy a 32Gb Class 10 SD card, about $20.00 + ship, prepare as usual and you'll cut your access time to the SD card buy about half. I can do a 2Gb recovery backup in about 5 and 1/2 min. With my Class 4 it takes just shy of 11 minutes.
More Memory Buy a Sandisk 64 Gb Class 10 Micro SD card, about 40.00 + ship, and partition the whole card as one Primary partition, format as FAT32, Sectors/ cluster 32 (16384 bytes) using "MiniTool Partition Wizard Home Edition" available for free here. I have donated to MiniTool since I use it for all kinds of partitioning,(resizing, moving, copy, etc.), on PC's and all kinds of flash memory. I started with the partition set to 30,451.33, copied my data from my 32G sdcard. It worked great and with SD boost set to 4096 all SD access was noticeably faster. So I used Partition Wizard to resize the card to the full capacity, the program changed the size and copied all the files in about 20 minutes. Plugged it into the Nook Color and went from 17 GB free to 47 Gb Free. It is a bit slower than the 32Gb & and the bootloader doesn't list CWM or TWRP recovery kernel or ram on the SD, but oh the storage. I can put over 40, 2 hr AVI or MPEG movies on the card and still have better than 20Gb free.
If you have other Apps, tricks, tweaks that you have tried and found to help. Please reply and I will try them out and list them if they do add to the smoother, longer, freer Nook.
Netflix on CM11 on SD
Good source of info. Thanks! Confirming that latest Netflix is working on SD. See that thread
If you use Speaker Boost try this to save memory.
Ever since CM7 and Nook Color Tweaks, in has been necessary to find a way to boost the sound output of our little wonder tablet. I tried several an ended up using Speaker Boost. I have found that I no longer need to use DSPmanager. The problem is that freezing or disabling the app doesn't keep it from installing in memory and using 18meg of precious RAM. Renaming the file with.bak extension or deleting it works after a reboot but, if you like to keep up with the nightlies like I do it is re-installed with every update. It gets to be a pain using a file manager to do this every day. So let your Nook do the repetitive work.
So I have worked up three quick and easy ways to rename the file.The best and easiest is the last.
1. Is a Tasker task. This was the first one I used and I setup a widget so I. Can rename with one tap. The.xml file can be imported as a task into Tasker.
2. Is an apk made from the Tasker task. It works the same way just doesn't need Tasker to work.
3. A script file that can run at every boot, check if DSPManager.apk exists, and rename it. This eliminates having to rename it and reboot after every ROM update as it is renamed before the app is loaded. It is only 279 bytes and is the only file that has to remain to work. In the 90RnamDSP scripts.zip below are three files. One that goes into userinit.d folder, an instruction.txt file and an installation script that sets everything in place just by running it.
I want to thank LeapinLar for the help he gave debugging the rename script. This was my first script and had to get everything in proper order and get the syntax correct. What I learned help me build and debug the installation script in a few hours.
Download, unzip, import, install, etc, and enjoy.
Thanks, nice job
Might check the links for the 6.x recovery threads
webyrd said:
Thanks, nice job
Might check the links for the 6.x recovery threads
Click to expand...
Click to collapse
Checked and corrected, Thanks.
pastordl... check pm about a couple of link issues
DizzyDen said:
pastordl... check pm about a couple of link issues
Click to expand...
Click to collapse
Thanks, guess we know where the missing link is.
problem with latest YouTube and Google Play apps not working
For problem with latest YouTube and Google Play apps not working, Go here:
http://forum.xda-developers.com/showpost.php?p=60241045&postcount=54
NEW EASY INSTALLER, RECOVERY ZIP
Total overhaul of code.
*HELP WANTED, PM FOR RELEVANT DETAILS*
This software package was originally just made for my personal use to rectify the issue of my phone not entering deep sleep when idle and me not having access to a charger for the majority of the day while also improving multitasking because being my phone is also my build environment/office environment, I am frequently jumping around various apps that I'd prefer to keep open.
Things this package accomplishes on your phone (very simple and brief summary):
*Forces entry into deep sleep as soon as the screen is off (if enabled, on by default). It also has audio detection so you can listen to music with the screen off without unwanted deep sleep entry.
*Improves multitasking, no more apps having to reload/redraw when you switch back to them.
*Automatic odexing of all apps, including new installs (if enabled, pre-lollipop ROM's).
*Easy management of swap.
*CPU management. You can set your own values to be locked (no other app can change them) or let its device manager automatically set CPU frequencies and the governor you specify.
*Dynamic Max CPU Freq: When enabled (on by default) it will automatically scale the max CPU frequency value depending on the CPU load. This can help with governors that favor the high end of the frequency table too much by allowing you to save battery but have the CPU power available when needed, without having to adjust anything manually whenever you go from doing something processor demanding to having your phone sit idle.
*Fixes issues with several kernels where the touch screen is unresponsive after waking the device. No more inconvenient force reboots.
*Enables all idle and suspend states available (they are disabled by default quite often) and can help get your device into the lower C-States.
*Fixes broken links to firmware files caused by buggy init scripts on some ROM's.
New/Other features:
*New recovery flashable installer
*Force system wide GPU rendering and faster framerate.
*Fixes Dt2w and Sw2w lock screen freeze bug.
*Now compatible with KSM.
*Faster app loading and responsiveness. Key android services are given priority status for I/O and CPU resources.
*Multitask over 20+ apps simultaneously without any redraws and low-latency app switching (provided you have the swap space)
Tip: I use the large amount of unused space on /system to increase the size of that MaxOpt managed swapfile.
*Fixed the crash on boot issue between MaxOpt and some kernels.
Default MaxOpt config:
•Swap on, default MaxOpt generated swapfile size is 64 MB, with one made on /data, one on /cache, and one on /system if mounted rw.
•Auto-odexing off.
•Hotplugging compatibility on.
•User CPU settings off, auto-device manager on.
•Deep Sleep immediately on screen off enabled.
•KSM off (you must have a kernel that supports it to enable this option and have it work).
•Kernel settings on.
•Everything is forced to be drawn by the GPU.
All of the above listed features are user optional/tuneable.
For those who wish to only use MaxOpt for fixing the lock screen freeze bug associated with some kernels/DT2W/S2W use the following link: http://forum.xda-developers.com/showthread.php?t=3061589
If you would like to just use individual components or adjust program settings from a terminal app, here is an example usage and description of their individual functions as well as other useful documentation (VERY OLD DOC, NEEDS LOTS OF UPDATES):https://docs.google.com/file/d/0B_hgNZE_j5sVbEN4ZUtkS2p0bW8/edit?usp=docslist_api
Terminal Emulator is what I would recommend for use with managing MaxOpts' settings.
System Requirements (not entirely sure due to lack of public testing):
Busybox
A terminal app
A kernel that can best be utilized by these programs.
Please make a nandroid backup before using.
And here is the MaxOpt installer ( R2 1.0.6 ):
* https://drive.google.com/file/d/0B_hgNZE_j5sVaGdxV0FfODdxbVU/view?usp=docslist_api
Changelog:
R2 v1.0.6- Adjustments to write buffering and multitasking memory performance.
R2 v1.0.5a- Fixed a bug present in both this project and MaxLife where data wasn't validated thoroughly enough before using it.
R2 v1.0.5- Added a new completely experimental new user tuneable (on/off, default off) that changes runtime memory allocation values. Only activate it if you have a large amount of swap.
R2 v1.0.0- Totally rebuilt the project, installable with a recovery flashable zip now, kernel image installer is no longer compatible and is scrapped.
For those still getting crashes:
The issue still appears to be related to the device radio when it happens, so, after a crash could you please force reboot your device and try to disable mobile data when it boots before it crashes again and please post a copy of /proc/last_kmesg. Thank you.
Screenshots of battery screen showing time spent in sleep:
https://docs.google.com/file/d/0B_hgNZE_j5sVSjRUU0ZlX0UwUWc/edit?usp=docslist_api
https://docs.google.com/file/d/0B_hgNZE_j5sVSmNjYThkUzAtNGM/edit?usp=docslist_api
https://docs.google.com/file/d/0B_hgNZE_j5sVcWxJd0JyV09nMDA/edit?usp=docslist_api
Please thank if my software has helped you and please leave logs and descriptions of problems if my software did not work for you.
Wow, this looks amazing. Very nice work.
I Will be playing with this for the next few days.
Sent from my Moto G using Tapatalk
Damn this looks complicated as hell haha. Good job OP
Very nice job
Thank you very much everyone. Glad for the positive feedback, this is my first public software release. I daylight in a machine shop, so this was far from my field of expertise and a long learning experience for me
I tried it on faux kernel 014m.
But my phone bootlooped
I have faux clock app.
Is it causing the problem?
Thanks
One possible problem could be the boot image it made was over 10 MB depending on the size of the input one. If that wasn't the issue, did you disable signature checking? Also this is currently not ART compatible. It is also important that you run the installer from a partition that supports octal permissions, so the emulated sdcard is a no go.
Edit: it may be worth trying disabling the faux clock app too. I don't have that kernel or app to try for myself but this mod does affect CPU settings so it could be a conflict. If none of those work, I may have to look into updating my installer with an alternate method for incompatible kernels.
elrod16 said:
One possible problem could be the boot image it made was over 10 MB depending on the size of the input one. If that wasn't the issue, did you disable signature checking? Also this is currently not ART compatible. It is also important that you run the installer from a partition that supports octal permissions, so the emulated sdcard is a no go.
Edit: it may be worth trying disabling the faux clock app too. I don't have that kernel or app to try for myself but this mod does affect CPU settings so it could be a conflict. If none of those work, I may have to look into updating my installer with an alternate method for incompatible kernels.
Click to expand...
Click to collapse
I followed steps as below:
I put that 2 files in the data partition.
Then boot.img of faux.
I set permission 755 for both files and boot.img
Then from terminal I executed the command.
I got new_image.img
I repack the zip using this new boot image and flashed it in recovery.
Then I reboot.
Phone booted and stuck on "optimizing apps 1 of 98"
Then again same.
Also I had 700mb of free memory when I tried this.
When I again booted using faux kernel I had 450mb of free memory.
Can you guess what's going wrong?
Did you disable APK signature checking?
elrod16 said:
Did you disable APK signature checking?
Click to expand...
Click to collapse
Sorry I forgot that.
Where exactly should I put those 2 files.
Was I doing right to put them in data partition?
And after first boot can I enable signature verification?
Do I need to disable it before every boot?
Unfortunately for now it needs to be off whenever an app is upgraded or added, but can be enabled after the reboot that that happens on, and yeah, /data works
Even after disabling signature verification it doesn't work on faux boot.img
Am I doing right?
For whatever reason it sounds like the dexy binary isn't playing well with your phone, I'll make a new installer with the option of disabling it for incompatible setups for the time being, but the other ones should still work. I'll keep ya posted.
My rom is stock 4.4.4
I will try again with disabled optimization.
kedar512 said:
My rom is stock 4.4.4
I will try again with disabled optimization.
Click to expand...
Click to collapse
OK, hopefully that should be the only part of this package not working for ya. Keep me posted, I'll continue trying to figure this out if it persists.
elrod16 said:
OK, hopefully that should be the only part of this package not working for ya. Keep me posted, I'll continue trying to figure this out if it persists.
Click to expand...
Click to collapse
No luck bro
Same problem.Stuck at optimization.
Should I try it on Xperience kernel?
Its not working with faux.
kedar512 said:
No luck bro
Same problem.Stuck at optimization.
Should I try it on Xperience kernel?
Its not working with faux.
Click to expand...
Click to collapse
I would say yeah, try it with it and see if it makes a difference
Also did you try the new build with a clean restore? (Before any of the failed install attempts) Try not wiping the cache/dalvik-cache after install and flash.
I tried again but this time booted upto lock screen and rebooted.
I tried with new build.
after placing ./maxopt boot.img appears running with dexy enabled.
That means it's already working? If yes, have to do anything else?
Every time you turn the meter will have to repeat the procedure?
Sorry my bad english