Dear friends,
When I end a call there is a delay of 3-5 seconds (sometimes more) until the call it actually ends.The issue appears when my phone is connected to a bluetooth handsfree. When the bluetooth is disconnected the call ends instantly.
Currently running Slim Bean 4.3 ROM, but I have noticed the same behavior with Paranoidandroid 3.98 and 3.99
Searching the net did not provided any solution.
Kindly ask you if anyone faced the same behavior and any suggestion towards its solution will be highly appreciated
Galaxy Note N7000
Bluetooth Samsun HS3000
Do you end the call using the headset button or the phone one?
Check using both methods, might be a characteristic of the headset itself.
Sent from my GT-N7000 using Tapatalk 4
Dear projeto56,
Thanks for the reply. I have tried both methods to end the call. and In both ways the same behavior is observed.
I believe that your reasoning is logical, since the issue appears only when the headset is connected, therefore I will try to connect a different headset and check the behavior, to rule out, or not, the headset.
Thank you again
EDIT: I have tried the same with another bluetooth headset (Jawbone Era) and the call ended almost instantly, so as projeto56 suggested it is related to the headset.
Thank you for the help
Related
Done this on loads of different devices with different bluetooth headset and the same result. Able to pair devices no problem. On making a call all one hears is a lot of static no voices. When answering a incoming call the same happens you answer the call but can't hear anything. Referred this the the ever helpfull O2 technical support who advised me to download latest Rom with the same result.
Any suggestions would be much appreciated.
Thanks in advance :roll:
Stupid question but you have tested the bluetooth headset with another phone and checked that its not actually the headset which is faulty?
I spent ages trying to diagnose a problem with my phone when I first got a wired GPS unit and it turned out in the end it was the unit not the phone.
Hi
I had the same problem. It disappeared after a hard reset.
Here is the similar thread: http://forum.xda-developers.com/viewtopic.php?t=41270
Hi everyone. I have had my Tilt for 4months now and it has given me a lot of joy. I have flashed and reflashed with no problems at all. I am currently using Schap's 4.31 Rom with 1.27.12.11 radio.
About a month ago i installed a new car stereo that has bluetooth connectivity with my phone - worked like a charm, paired very easily and generally appeared to be working with no probs.
Then i noticed that if i was in a bluetooth conversation and somebody else was calling (on call waiting), if i switched calls i could not hear anything, and if i ignored the second call, when the person on call waiting hang up, both conversations were terminated. I thought it was odd, but i just deactivated call waiting and thought, "let them try calling me later".
The other, a lot more serious problem, is that sometimes, randomly as far as i realised, the phone will go totally silent - incoming calls won't ring, and when i try to make a call, when i press "talk" then phone does not make that beep that it makes when an outgoing call is initiated. Should the person i call pick up i cannot hear them at all.
A soft reset takes care of this problem, but it has happened to me 3 times already, and i think it was after a bluetooth call.
Has anybody faced this problem before? I need to be available on the phone 24/7 due to my work and i really need to find a solution for this. Yesterday afternoon i took a nap for 45 minutes and had six missed calls that i never heard cause the phone never rang.
The phone is always on "ring" and at full volume.
Any ideas would be welcome.
Thanks
Alkis
Same issue
I'm assuming since I also am facing this same problem that it is not uncommon. It seems to me that it happens after a bluetooth device is turned off. Somehow it sets the volume on everything to mute. I thought only a soft reset would fix it until I discovered that it was just shutting off the volume. Still annoying, though.
Tilt problems with phone going silent
This problem has occurred with my phone every since upgrading to the WM 6.1 and it is related to a bluetooth device being hooked up. Often when someone calls the ringer will go from vibrate to on, but the volume turns all the way off. It will then cycle to off completely. The cycling occurs when a call comes in or when I hang up. I can stop this problem from happening by disconnecting the bluetooth head set. I have tried three different headsets and the problem occurs with all of them (Jawbone I, Jawbone II, and Plantronics) so I know it is not the brand of headset. HTC said to try a download of a screen dimmer problem, but have not done that yet. Anyone have any better advice?
did u guys ever find a solution to this?
its quite annoying missing calls because my phone decides to go silent for some reason
Same issue with GPS
I have the same issue, even when using software that accesses the GPS via bluetooth port. Muting is irritating, but at least voicemail catches messages. What really bothers me is that sometimes the mute is turned off and the volume up, especially when in a private meeting where we do not want interruptions
Gregg
HTC Tytn II bluetooth causes silent setting
I too have had the issue where my phone will go into total silent mode after using my bluetooth stereo hands-free feature. It doen't happen after using my bluetooth headset though.
It happens pretty regular that after using the bluetooth hands-free of my JVC car stereo that when I take the phone elsewhere it is totally silent. no ringer, no alarm (Ptravel alarm is what I use), no audio if I make a call (or receive a call).
It also will cause the phone to be silent on subsequent calls on the bluetooth stereo hands-free: ie: I take a call, hang up and another call will come in and I can answer it but have no audio.
My Tytn II is running the HTC (AT&T) WM 6.1 upgrade. The only thing I have done is use the Advanced configuration manager and the Kaiser tweak to change a few settings for performance and visual enhancements.
I see others are having the same problems.....Has anyone else used the tweaks and maybe that is root of the problem?
Has anyone discovered a fix (really important). My only options are to soft reset every time I get out of the car or not use the JVC bluetooth capability (which is why I replaced the stock radio in the first place).
Thanks
Hi rrackman,
I'd advice for you to look at the following thread:
http://forum.xda-developers.com/showthread.php?t=438457
It's quite long, so better subscribe to it and wait for responses. Several people with Tilt's have the same problem. Myself I have a JVC NX-7000 and an unbranded Kaiser (HTC TyTN II). It works fine with WM6.0, but I have the same issues you mention with WM6.1. First advice while we're searching for the solution: downgrade to WM6.0...
Regards,
Nika.
Is there a solution to this problem?
Try WM6.0 ROM - check out the thread I mention in my sig.
Regards,
Nika.
I did indeed take a look at the thread you linked earlier. Sorry for making the quick post earlier, I should have mentioned that this is regarding the "unexplained volume drop to zero" symptom, not the NSI symptom. Fortunately I don't have the NSI problem, just the drop to zero problem.
Of course downgrading to 6.0 would be the key solution, was just hoping to find a way to avoid doing just that. My phone never had the problem prior to 6.1 and was running the exact same list of applications and settings.
Hi!
I have one black X1i SW ver R3AA010, GENERIC_UK rom.
Great phone, but i have problem with the wired factory headset.
If i have call, phone playing ringtone, and i want receive this call, but no effect. Another problem is mic is on the phone enabled, not on the headset - in ear-phone mode.
On another forums reported same problem.
I see now only one solution:
1.,Unplug Headset from phone
2.,Incoming call, after hearing rintone - plug in the headset
3.,Problem is fixed..., but only to next soft reset or next unplug
Is there any registry mod or cab fix to this?
example : manual headset mode on/off
pls help me, thank you
As you mention, the problem has been scarcely discussed in other threads (and forums), but no one's seemed to find a solution. I'm not even aware if the headset problem is a general flaw in X1, or we're just a few unfortunates.
I won my X1 in a competition so I don't think I'm really in a position to be pissed off, but this defect is indeed a MAJOR drawback, and it surprises me it hasn't been criticised more loudly in e.g. reviews and forums.
The problem smells to me like a firmware issue (though I really don't have a clue), i.e. something that our friends at Sony Ericsson (are you out there, guys?) should be able to fix in an update, but they don't.. :-(
Anyway, my workaround is to make sure the headset is 'armed' in advance whenever I want to be prepared for an incoming or outgoing call. E.g. before I hop on my bicycle, I 'simply' make a short call to whatever number, e.g. to my voicemail, and as soon as there's a connection I plug in my headset and hang up. Now the headset works - I test it by pressing the headset button twice, which should initiate redialling the last number used.
In any case, it shouldn't be necessary to make such arrangements! My previous mobile was a crap, crap Nokia - but I miss it because its headset worked like a charm.
In fact, just out of curiosity - if anyone reading this has an X1 without any headset problems (i.e. mic and button not being responsive), please speak up. Maybe we can then isolate the problem.
Hi there,
I've got a xperia z with a stock rom(android 4.1.2 build 10.1.A.1.434.) and a Plantronics Voyager Legend Bt Headset(running with the latest firmware).
The phone is new, only one week old. I've installed only few programs (beside the bloatware already on the phone).
One out of that is "avast mobile security", not sure if it's a possible fault for the problems I'm going to describe...:
The Headset is paired and I can, sometimes, use it.
Sometimes the headset gets disconnected from the mobile phone during calls(to get the call back on headset I need to turn bt on/off on the xz)
Sometimes the headset states "connected to phone 1" but when I start a call it's not possible to use the headset (same fix, bt on/off on the xz)
Also the Voice Commands are not working, a black page pops up and closes immediately.
The same Headset is paired with a Samsung S2, and there are no problems with that phone.
(...except voice commands, I've never tried them on that phone...)
Has somebody similar problems with a bt headset and this phone?
Has somebody similar problems with the same bt headset and this phone?
Is there a "magic app" that could fix problems or help debugging this problem?
(- I've tried the plantronics app, but this one was very unstable so I removed it.)
Kind regards
known issue
Win**** said:
Hi there,
I've got a xperia z with a stock rom(android 4.1.2 build 10.1.A.1.434.) and a Plantronics Voyager Legend Bt Headset(running with the latest firmware).
The phone is new, only one week old. I've installed only few programs (beside the bloatware already on the phone).
One out of that is "avast mobile security", not sure if it's a possible fault for the problems I'm going to describe...:
The Headset is paired and I can, sometimes, use it.
Sometimes the headset gets disconnected from the mobile phone during calls(to get the call back on headset I need to turn bt on/off on the xz)
Sometimes the headset states "connected to phone 1" but when I start a call it's not possible to use the headset (same fix, bt on/off on the xz)
Also the Voice Commands are not working, a black page pops up and closes immediately.
The same Headset is paired with a Samsung S2, and there are no problems with that phone.
(...except voice commands, I've never tried them on that phone...)
Has somebody similar problems with a bt headset and this phone?
Has somebody similar problems with the same bt headset and this phone?
Is there a "magic app" that could fix problems or help debugging this problem?
(- I've tried the plantronics app, but this one was very unstable so I removed it.)
Kind regards
Click to expand...
Click to collapse
its a known issue with bluetooth headsets. But I have a Sony MDR-1RBT and i have never had music skip. At the same time, not so lucky if i am listening on the free NFC speaker I got from Clove. Its a bit hit and miss really. May be do a factory reset and try again. If not try to replicate the issue and go to the nearest Sony Center for a warranty case ?
I just wanted to add that I have a Nexus 4 with the Plantronics Voyager Legend and I'm having the same issue of random disconnects during a call. I'm running AOKP on my phone. I still haven't figured out how to fix it, but this is not just happening on the Sony Xperia Z.
Same problem
WillJitsu said:
I just wanted to add that I have a Nexus 4 with the Plantronics Voyager Legend and I'm having the same issue of random disconnects during a call. I'm running AOKP on my phone. I still haven't figured out how to fix it, but this is not just happening on the Sony Xperia Z.
Click to expand...
Click to collapse
Hi, I have been experiencing the same issue on my Xperia LT28i also known as international Ion for several months now. I think I started having it around the time when I upgraded to ICS. Since then performed 2 hard resents but problem didnt go away. Nothing like this was experienced on Gingerbread (the version of the OS that came with the phone...
BTW, I am using two differen bluetooth earpieces - a Jabra and a Jawbone. Both have the same problem with sony - random transfer of teh conversation from the earpiece to the phone. this is really annoying when driving... Sometimes it gets worse and does it every 5 mins. other times wont happen an entire day...
I waited for 6 month for the JB update, hoping it would cure the problem. Updated to JB on AUG 1 but the problem persists. Thinking about sending the phone to Sony for repair...
---------- Post added at 06:37 AM ---------- Previous post was at 06:32 AM ----------
Win**** said:
Hi there,
I've got a xperia z with a stock rom(android 4.1.2 build 10.1.A.1.434.) and a Plantronics Voyager Legend Bt Headset(running with the latest firmware).
The phone is new, only one week old. I've installed only few programs (beside the bloatware already on the phone).
One out of that is "avast mobile security", not sure if it's a possible fault for the problems I'm going to describe...:
The Headset is paired and I can, sometimes, use it.
Sometimes the headset gets disconnected from the mobile phone during calls(to get the call back on headset I need to turn bt on/off on the xz)
Sometimes the headset states "connected to phone 1" but when I start a call it's not possible to use the headset (same fix, bt on/off on the xz)
Also the Voice Commands are not working, a black page pops up and closes immediately.
The same Headset is paired with a Samsung S2, and there are no problems with that phone.
(...except voice commands, I've never tried them on that phone...)
Has somebody similar problems with a bt headset and this phone?
Has somebody similar problems with the same bt headset and this phone?
Is there a "magic app" that could fix problems or help debugging this problem?
(- I've tried the plantronics app, but this one was very unstable so I removed it.)
Kind regards
Click to expand...
Click to collapse
Hi, I have been experiencing the same issue on my Xperia LT28i also known as international Ion for several months now. I think I started having it around the time when I upgraded to ICS. Since then performed 2 hard resents but problem didnt go away. Nothing like this was experienced on Gingerbread (the version of the OS that came with the phone...
BTW, I am using two differen bluetooth earpieces - a Jabra and a Jawbone. Both have the same problem with sony - random transfer of teh conversation from the earpiece to the phone. this is really annoying when driving... Sometimes it gets worse and does it every 5 mins. other times wont happen an entire day...
I waited for 6 month for the JB update, hoping it would cure the problem. Updated to JB on AUG 1 but the problem persists. Thinking about sending the phone to Sony for repair...
Love the Note 8 and everything about it except how it interacts with bluetooth headsets. I troubleshooted starting with a few bluetooth devices LG HBS1100, Samsung Flex, Motorola earpiece and car audio bluetooth. Here are a few things I encountered:
1. None of answer call buttons on the headsets will answer calls, even the Samsung Flex does not function properly
2. If you using an internet driven app such as Skype, WhatsApp etc, it is the worse. In addition to the buttons not working properly
A. The call waiting feature does not work when using internet audio or video it disconnects those call and allow the other call to come through sometimes unprompted.
B. If you are using Skype, WhatsApp etc, sometimes the call suddenly drops, battery still medium to full on the headsets.
C. A and B only happens with bluetooth headsets, call waiting function as design with car bluetooth calls and traditional BT earpieces
Im am posting this because a phone with this price tags should have overcome these discrepancies , the company should have come across this somehow during testing hmmm. It was almost a deal breaker but I like having a stylus, beautiful screen , phone design and the note taking features. I have friends that I communicate with overseas but I don't call them everyday or I will just use the speaker phone when Im talking to them.
I came from a 7 plus and all features on the BT headsets worked (Not enough to sway me back to Apple but its just confirmation.)
Has anyone experience these and what was the remedy if there was one Thanks..... or dead I get sent a lemon?
Never owned a Bluethooth. ?
Sent from my Galaxy Note8 using XDA Labs
Have been using 2 bluetooth headsets and a Gear S2 watch to answer calls, have been able to make and take calls without a fuss, although I've always used the phone itself or the watch to answer a call. Never used call waiting. I use Viber as well to receive calls and never had a problem and no drops.
I had some odd issues when connected to my Car Blue tooth - I was using Hotspot on my phone to connect my Car's Android Navigation system - listening to I Heart Radio in the car - made a call - call connected - but several times during the call - Blue tooth suddenly disconnected for about 10 seconds and then reconnected.
This happened several times on different calls. I don't know if using WIFI while I was connected to blue tooth had anything to do with this - and I don't have the note any more (I returned it because it was OEM Locked ) should have an unlocked version next week and I will try again. But I saw your post and thought I would share.
My Senheiser MB pro 2 works fine with the Note 8. If there is any tests you want me to perform let me know.
Only thing I noticed today was that if I went out of range, the headset and phone would not auto reconnect when in range again , not sure if this is normal or not.
I have a Plantronic Edge. When I'm on Duo it starts the video call fine and after a few seconds it disconnects and goes to the speaker. So far it only does this in that app or at least that I can tell.
Issue with me is I don't recall how the behavior of my Bluetooth headset was on my other previous phone's, like I mentioned it disconnected when I was out of range then didn't reconnect automatically. Should it reconnect automatically?
Sent from my SM-N950U using Tapatalk
Bluetooth headset issues
Problem solved it was the phone. Verizon gave me a new one and this one works perfect. Thanks for your responses
Problem solved, was user error. Thanks for the feedback guys.
Sent from my SM-N950U using Tapatalk