Database Develop

[Q] Please help me with my Note GT-N7000 (I might have bricked it)

My Galaxy Note GT-N7000 was on CM10 last night and I followed Zedomax's rootgalaxynote.com GT-N7000 unrooting method and when I was installing the Mobile Odin Lite on my phone, it said it needs to download more add-on to be able to flash it, then all the sudden my internet connection was down, so I couldn't download it, but followed his instruction and tried wipe and factory reset, but it got stuck at formatting (no progress), then I flashed cm9 again, but it was stuck at cm9 boot logo, nothing else. Then I followed Zedomax's rootgalaxynote.com's first method using my Computer Desktop but
"<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DXKL1_N7000OLBKJ6_N7000DXKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> factoryfs.img
" it got stuck at here, no progress. The only thing I can do with my phone is that to either put on download mode or it says "Firmware upgrade encountered an isssue. Please select recovery mode in Kies & try again." Please help me with this friends. I am looking forward to your help. Thank you.
Khai.

you give not detail as needed. but nevermine, from the last part it seems you has bricked your phone.
i think you might need to refer "hg42" thread to revive your note.
Sad to be hear that.
Sent from my GT-N7000 using xda premium

immediately contact dr.ketan
khaino said:
My Galaxy Note GT-N7000 was on CM10 last night and I followed Zedomax's rootgalaxynote.com GT-N7000 unrooting method and when I was installing the Mobile Odin Lite on my phone, it said it needs to download more add-on to be able to flash it, then all the sudden my internet connection was down, so I couldn't download it, but followed his instruction and tried wipe and factory reset, but it got stuck at formatting (no progress), then I flashed cm9 again, but it was stuck at cm9 boot logo, nothing else. Then I followed Zedomax's rootgalaxynote.com's first method using my Computer Desktop but
"<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DXKL1_N7000OLBKJ6_N7000DXKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> factoryfs.img
" it got stuck at here, no progress. The only thing I can do with my phone is that to either put on download mode or it says "Firmware upgrade encountered an isssue. Please select recovery mode in Kies & try again." Please help me with this friends. I am looking forward to your help. Thank you.
Khai.
Click to expand...
Click to collapse
Contact dr.ketan for yr solution. He is the sweet n right person to guide u.

khaino said:
My Galaxy Note GT-N7000 was on CM10 last night and I followed Zedomax's rootgalaxynote.com GT-N7000 unrooting method and when I was installing the Mobile Odin Lite on my phone, it said it needs to download more add-on to be able to flash it, then all the sudden my internet connection was down, so I couldn't download it, but followed his instruction and tried wipe and factory reset, but it got stuck at formatting (no progress), then I flashed cm9 again, but it was stuck at cm9 boot logo, nothing else. Then I followed Zedomax's rootgalaxynote.com's first method using my Computer Desktop but
"<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000DXKL1_N7000OLBKJ6_N7000DXKJ3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> factoryfs.img
" it got stuck at here, no progress. The only thing I can do with my phone is that to either put on download mode or it says "Firmware upgrade encountered an isssue. Please select recovery mode in Kies & try again." Please help me with this friends. I am looking forward to your help. Thank you.
Khai.
Click to expand...
Click to collapse
the ever GOLDEN RULE: Don't ever ever attempt to WIPE data if your on a unsafe or on a stock ICS kernel. That's should be at the top of your list before you do anything on your phone. If you need to WIPE, make sure your already in a safe kernel or if you haven't still, then flash one.
Now going back on your perennial issue. The only thing you can and will do is FLASH a stock GB on download mode using PC ODIN. Yes Doc Ketan's thread/s have those old GB's ROM.. -> http://forum.xda-developers.com/showthread.php?t=1424997, follow it to a tee.
One added thing when your going to start to flash GB again... Pray, that it would not stuck back again at 'factoryfs.img'
Good luck bud!

No luck...yet.
letters_to_cleo said:
the ever GOLDEN RULE: Don't ever ever attempt to WIPE data if your on a unsafe or on a stock ICS kernel. That's should be at the top of your list before you do anything on your phone. If you need to WIPE, make sure your already in a safe kernel or if you haven't still, then flash one.
Now going back on your perennial issue. The only thing you can and will do is FLASH a stock GB on download mode using PC ODIN. Yes Doc Ketan's thread/s have those old GB's ROM.. -> http://forum.xda-developers.com/showthread.php?t=1424997, follow it to a tee.
One added thing when your going to start to flash GB again... Pray, that it would not stuck back again at 'factoryfs.img'
Good luck bud!
Click to expand...
Click to collapse
I spent two days straight working on it, but no luck. I think I am gonna contact Samsung and send it to them for the warranty and I don't know if they would know that I rooted it. But I am just gonna give a try. Please share your knowledge and thoughts. Thank you.

Reflash it with PC odin (Again? )... refer to Dr Ketan... I encounter same issues before, I just try try to reflash old GB... link at #4

khaino said:
I spent two days straight working on it, but no luck. I think I am gonna contact Samsung and send it to them for the warranty and I don't know if they would know that I rooted it. But I am just gonna give a try. Please share your knowledge and thoughts. Thank you.
Click to expand...
Click to collapse
Can you get the Note into Download mode?
If so, try using desktop Odin (latest desktop version not mobile version) and flash the Abyss 4.2 kernel. the Tar file is easily found on XDA. This is a GB kernel and should allow you to get into full Recovery. From there you can flash a new ROM as you are now on a safe kernel.

Tried that, but not sure about the latest desktop version.
Alba Donzo said:
Can you get the Note into Download mode?
If so, try using desktop Odin (latest desktop version not mobile version) and flash the Abyss 4.2 kernel. the Tar file is easily found on XDA. This is a GB kernel and should allow you to get into full Recovery. From there you can flash a new ROM as you are now on a safe kernel.
Click to expand...
Click to collapse
Hi, thank you for your message, I was on Abyskernel when I factory data reset, and tried to flash back to cm9 from cm10, but no luck. Then I used Odin3-v1.85 on desktop with Gingerbread Rom, it got stuck at factoryfs.img.. I have tried with different pc disabling firewall and anti virus. What is the latest desktop version of Odin that you know? What specific tar file do you know that is the best? Thank you again.

khaino said:
Hi, thank you for your message, I was on Abyskernel when I factory data reset, and tried to flash back to cm9 from cm10, but no luck. Then I used Odin3-v1.85 on desktop with Gingerbread Rom, it got stuck at factoryfs.img.. I have tried with different pc disabling firewall and anti virus. What is the latest desktop version of Odin that you know? What specific tar file do you know that is the best? Thank you again.
Click to expand...
Click to collapse
Latest Odin is 3.0.4
Sent from my GT-N7000 using xda app-developers app

khaino said:
Hi, thank you for your message, I was on Abyskernel when I factory data reset, and tried to flash back to cm9 from cm10, but no luck. Then I used Odin3-v1.85 on desktop with Gingerbread Rom, it got stuck at factoryfs.img.. I have tried with different pc disabling firewall and anti virus. What is the latest desktop version of Odin that you know? What specific tar file do you know that is the best? Thank you again.
Click to expand...
Click to collapse
your CM10 to CM9 downgrade sounds like a bad flash, it can happen. I would try Odin3 V3.05 with Abyss (search for "AbyssNotekernel42CWTouchOriginalLogo.tar" or go here - https://www.dropbox.com/s/yoe791qq3atbung/AbyssNotekernel42CWTouchOriginalLogo.tar).
this should allow you to install a safe kernel to flash from. if you can now access Recovery, then you can flash a ROM from there. I would use a Stock based one (I always recommend Chrack ROM or Criskelo), If you prefer, you can download a Stock tar file and use Odin but I would try downloading the latest Chrack ROM or Criskelo ROM, transferring it to your micro SD and flashing after you have installed the Abyss tar.
I hope this helps. Please hit Thanks if it did.

Question!
Alba Donzo said:
your CM10 to CM9 downgrade sounds like a bad flash, it can happen. I would try Odin3 V3.05 with Abyss (search for "AbyssNotekernel42CWTouchOriginalLogo.tar"
this should allow you to install a safe kernel to flash from. if you can now access Recovery, then you can flash a ROM from there. I would use a Stock based one (I always recommend Chrack ROM or Criskelo), If you prefer, you can download a Stock tar file and use Odin but I would try downloading the latest Chrack ROM or Criskelo ROM, transferring it to your micro SD and flashing after you have installed the Abyss tar.
I hope this helps. Please hit Thanks if it did.
Click to expand...
Click to collapse
You gave me the AbyssNotekernel, but the only thing my phone can now do when I turn on is either show a screen with "Firmware upgrade encounters an issue. Please select recovery mode in Kies and try again" or on download mode. Or is there any way I can use the Desktop Odin and try to install the AbyssNotekernel that you gave me? I really don't know bro. Thank you for the message, please let me know.

khaino said:
You gave me the AbyssNotekernel, but the only thing my phone can now do when I turn on is either show a screen with "Firmware upgrade encounters an issue. Please select recovery mode in Kies and try again" or on download mode. Or is there any way I can use the Desktop Odin and try to install the AbyssNotekernel that you gave me? I really don't know bro. Thank you for the message, please let me know.
Click to expand...
Click to collapse
Yes, the Abyss tar file is for use with Odin. install Odin on your PC, put the Note into Download and connect. Flash the tar file and wait for the Note to reboot (search for notes on how to flash with Odin if you're not 100% sure). you should now be able to use Recovery to flash a ROM from this safe kernel.

Just a quick question.
Alba Donzo said:
Yes, the Abyss tar file is for use with Odin. install Odin on your PC, put the Note into Download and connect. Flash the tar file and wait for the Note to reboot (search for notes on how to flash with Odin if you're not 100% sure). you should now be able to use Recovery to flash a ROM from this safe kernel.
Click to expand...
Click to collapse
Sorry I didn't explain in details, I am on pc Odin version 3.07 and clicked on PDA but the Abyss tar file is not appearing there even after unzipping it a couple of times on the desktop. Please let me know bro. Thank you for your response.
Khai.

khaino said:
Sorry I didn't explain in details, I am on pc Odin version 3.07 and clicked on PDA but the Abyss tar file is not appearing there even after unzipping it a couple of times on the desktop. Please let me know bro. Thank you for your response.
Khai.
Click to expand...
Click to collapse
.tar file is to be flashed with odin directly. It has an image inside and should not extract it. Should put the .tar file in one folder but not on desktop screen. Select pda box in odin and brow to the folder where you put .tar file. Should see it there.
BTW, if flash using CWM failed again, then should use hg42 scanner to check if there is partition damage.
http://forum.xda-developers.com/showthread.php?t=1823918

Update.
forest1971 said:
.tar file is to be flashed with odin directly. It has an image inside and should not extract it. Should put the .tar file in one folder but not on desktop screen. Select pda box in odin and brow to the folder where you put .tar file. Should see it there.
BTW, if flash using CWM failed again, then should use hg42 scanner to check if there is partition damage.
http://forum.xda-developers.com/showthread.php?t=1823918
Click to expand...
Click to collapse
Thanks for your patience on your instruction, I actually was able to flash the Abysskernel that you gave me with ODIN and it went straight to the recovery mode, but then I can't install anything, then I put it back to download mode and tried to flash a Gingerbread ROM, but as always it got stucked at factoryfs.img. What do you think I can do bro? Please let me know about it. Thank you.
Khai.

khaino said:
Thanks for your patience on your instruction, I actually was able to flash the Abysskernel that you gave me with ODIN and it went straight to the recovery mode, but then I can't install anything, then I put it back to download mode and tried to flash a Gingerbread ROM, but as always it got stucked at factoryfs.img. What do you think I can do bro? Please let me know about it. Thank you.
Khai.
Click to expand...
Click to collapse
It seem to show you have an emmc brick, although using the partition scanner will confirm. The options are to send to ss service for warranty or to revise using repartition. For warranty you will need to reset flash counter using a jig.
Sent from my phone

Update and question.
forest1971 said:
It seem to show you have an emmc brick, although using the partition scanner will confirm. The options are to send to ss service for warranty or to revise using repartition. For warranty you will need to reset flash counter using a jig.
Sent from my phone
Click to expand...
Click to collapse
Hi bro,
I flashed the Abysskernel again and it went to Samsung Galaxy Note GT-N7000 logo with big Triangle at the bottom and it then goes to Android system recovery <3e>, then it looks like there is no option for me to access the SD card, but its own 16GB storage it came with and that one has CM10 in it. Tried to flash that, but it says "E:failed to verify whole-file signature". If I attempt to claim for warranty will Samsung know that I rooted it after clearing the binary counts? Please let me know. Thank you for your instructions. If there is anything else you want me to try out, please let me know. Thank you.
Khai.

khaino said:
Hi bro,
I flashed the Abysskernel again and it went to Samsung Galaxy Note GT-N7000 logo with big Triangle at the bottom and it then goes to Android system recovery <3e>, then it looks like there is no option for me to access the SD card, but its own 16GB storage it came with and that one has CM10 in it. Tried to flash that, but it says "E:failed to verify whole-file signature". If I attempt to claim for warranty will Samsung know that I rooted it after clearing the binary counts? Please let me know. Thank you for your instructions. If there is anything else you want me to try out, please let me know. Thank you.
Khai.
Click to expand...
Click to collapse
Once reset flash counter the triangle will go and you can flash a stock kernel find link from dr.ketan toolbox, then it is ok to send to warranty.
Sent from my phone

Update.
forest1971 said:
Once reset flash counter the triangle will go and you can flash a stock kernel find link from dr.ketan toolbox, then it is ok to send to warranty.
Sent from my phone
Click to expand...
Click to collapse
Hi bro, it somehow managed to get on CWM and but any flashing was aborted. And tried to flash Criskelo, but got stuck at installing, no progress. What should I do? Thank you.

Just two options above, warranty or repartition.
Sent from my phone

[Q] Galaxy Note doesn't go beyond logo and stuck at Downloading.. PLZ HELP :(

Hello all,
I read now the warning post and I understand now that probably I shouldn't have done it (so please be gentle ).. however maybe someone can still help me with my situation:
I've rooted my Galaxy Note with ClockworkMod recovery successfully and then busybox.
Then I went to recovery mode again (after restarting the phone), however it loaded Android regular recovery mode (not Clockwork), so I installed Clockwork again and without restarting performed WIPE DATA (maybe that was also a mistake?). After it was finished it restarted by itself and now its in the following status:
- stucks at GALAXY NOTE N7000 logo. Sometimes blinks, but never goes beyond it.
- Recovery mode exactly same - stuck at logo.
- when plugging USB it will show the battery, but it's like stuck then.
- Tried download mode, but it's stuck at Downloading... forever.
I couldn't find the exact case as mine, that it restarted by itself and stuck at logo now.
I backed up everything, the previous ROM and etc.
I am aware of the bricking bug of ICS, however I had the ClockworkMod installed, so what did I do wrong??
And most importantly, what should I do now? Can I do something via the download mode? I don't think Odin recognizes any connected device when I plug in the USB, but I don't know how to check if it does or not..
Thanks in advance!

Switch to download mode, connect to PC and install a stock JB (be sure to install the USB drivers before).
Make a snapshot of the errors an post it here.

http://forum.xda-developers.com/showthread.php?t=1424997
May be this helps ...
Just flash a new stock rom..
Sent from my GT-N7000 using xda premium

i believe u use wrong kernal so it's stuck ！ if u don't ever do any factory reset or wipes then u're stillsafe ！
if u do so ? then just follow the instructions above given by the 2members here ：p
if u still haven't do any wipes n factory reset then look for philz safe kernal wif ur rom version flash it n let it update for mins
n ur phone will resume operation ！

Trying
alvinhaw said:
i believe u use wrong kernal so it's stuck ！ if u don't ever do any factory reset or wipes then u're stillsafe ！
if u do so ? then just follow the instructions above given by the 2members here ：p
if u still haven't do any wipes n factory reset then look for philz safe kernal wif ur rom version flash it n let it update for mins
n ur phone will resume operation ！
Click to expand...
Click to collapse
Trying all that right now, will keep you posted.

what is my stock ROM?
whatever61 said:
Trying all that right now, will keep you posted.
Click to expand...
Click to collapse
I don't understand this.. my stock ROM was:
Baseband Version: N7000XXLB2
Kernel Version: 2.6.35.7-N7000XXLC1-CL1003701 [email protected] #2
Build number: GINGERBREAD.XXLC1
I don't know what coutnry, I bought it from Netherlands, I live in Belgium, but it could be from any country in the region!
I cannot find this one exactly. I find many with N7000XXLB2 and many with N7000XXLC1.
Which one should I choose?
Also, can I install a JB or ICS directly?

Please let me know I'm doing it right (cause this is getting really insanely ridicilous):
1. I install PhilZ recovery mode via the phone recovery mode.
2. I install a stock ROM (I tried many) via Odin download mode.
All the time stuck as Galaxy N7000 logo. Never goes past it.
Every time I install a stock ROM it also removes the Philz recevory mode, but maybe that's ok..
Anything I'm doing wrong??

Why don't you follow my advice from second post and then show us a snapshot of PC Odin.
No need for Philz when installing a stock Rom with PC Odin (it's always deleted).
And tell us what Rom you install.

ThaiDai said:
Why don't you follow my advice from second post and then show us a snapshot of PC Odin.
No need for Philz when installing a stock Rom with PC Odin (it's always deleted).
And tell us what Rom you install.
Click to expand...
Click to collapse
So I don't wipe anything and just go to download mode and install a PDA file of a STOCK ROM, that's it?
I tried that, but now I will be more specific (and in another guide they say to do some steps before, so its very confusing already).
I also asked above how do I know which ROM I should install?
and also, how do I get errors log? there were no errors when I was installing the PDA..

whatever61 said:
So I don't wipe anything and just go to download mode and install a PDA file of a STOCK ROM, that's it?
I tried that, but now I will be more specific (and in another guide they say to do some steps before, so its very confusing already).
I also asked above how do I know which ROM I should install?
and also, how do I get errors log? there were no errors when I was installing the PDA..
Click to expand...
Click to collapse
Just let THAIDAI knows which stock rom u're flashing !

alvinhaw said:
Just let THAIDAI knows which stock rom u're flashing !
Click to expand...
Click to collapse
Ok, here we go.
I was trying with ROM: N7000XXLC1_N7000OXALC1_N7000XXLB2_HOME.tar.md5
This is what I got from Odin (I hope that's what you meant by snapshot and not actual screenshot or something ):
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLC1_N7000OXALC1_N7000XXLB2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> factoryfs.img
<ID:0/008> NAND Write Start!!
<ID:0/008> zImage
<ID:0/008> hidden.img
<ID:0/008> modem.bin
<ID:0/008> cache.img
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
This is something new: just after it was completed it booted to recovery mode and gave me the following message:
Android system recovery <3e>
Finding update package
bla bla
Successfuly installed package.
Wiping cache..
Formatting /cache
Cache wipe complete.
E:failed to mount /data (unknown error: 0)
your storage not prepared yete, please use UI menu to format and reboot actions.
copy application failed.
Applying multi-CSC
Can't access to '/system/csc/ATO/system'
Successfully applied multi-CSC.
and it still doesn't boot.. gonna try another ROM now and post here the results.

Now tried with:
N7000XXLRI_N7000XXLRB_N7000XEFLP2_HOME.tar.md5
This is the original original ROM that I had when I just bought the phone.3
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLRI_N7000XXLRB_N7000XEFLP2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> SetupConnection..
<ID:0/008> Initialzation..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> cache.img
<ID:0/008> NAND Write Start!!
<ID:0/008> factoryfs.img
<ID:0/008> hidden.img
<ID:0/008> modem.bin
<ID:0/008> zImage
<ID:0/008> RQT_CLOSE !!
<ID:0/008> RES OK !!
<ID:0/008> Removed!!
<ID:0/008> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
No going into recovery mode after restart this time and still same problem.

when you flash a stock rom with pc odin, the phone may not boot. If you have flashed a GB rom then when you are stuck at logo enter stock recovery with three button combo and then wipe data factory reset, wipe cache and then reboot.

I flashed a stock rom as explained above, not a GB. I tried wiping cache and all data through recovery. Nothing helps. You say it might not boot, so how do I make it boot with Stock ROM?

stock roms can be ginger bread (GB), or ICS or JB (jelly Bean)
flash a GB stock rom, wait for the proceedure to finish completely, when you see its not booting then use three buttons to get into stock recovery and then wipe then reboot

rraaka said:
stock roms can be ginger bread (GB), or ICS or JB (jelly Bean)
flash a GB stock rom, wait for the proceedure to finish completely, when you see its not booting then use three buttons to get into stock recovery and then wipe then reboot
Click to expand...
Click to collapse
I already did, the last post was a GB, i tried to wipe out everything afterwards also.

ThaiDai, please see my replies, I did as you requested..
Thanks

whatever61 said:
I've rooted my Galaxy Note with ClockworkMod recovery successfully and then busybox.
Then I went to recovery mode again (after restarting the phone), however it loaded Android regular recovery mode (not Clockwork), so I installed Clockwork again and without restarting performed WIPE DATA ...
....I am aware of the bricking bug of ICS, however I had the ClockworkMod installed, so what did I do wrong??
Thanks in advance!
Click to expand...
Click to collapse
By "ClockworkMod" you mean CWM.zip right? This is a temporary recovery that disappears upon reboot. It also LETHAL to wipe with when running on top of a stock ICS kernel.
So to sum up;-
You were running Stock ICS.
You flashed CWM.zip (from YouTube or where ever) from stock 3e recovery and then flashed Root/busybox file.
Booted back into stock recovery, flashed CWM.zip again and performed wipe data/factory reset with it.
How am I going so far?
Bad news - you have most likely superbricked your device.
If so,new MOBO or repartition is only way out now

it might be mess up.. try get 5files wif bootloader n place it accordingly in odin .
go here to study http://forum.xda-developers.com/showthread.php?t=1424997

shoey63 said:
By "ClockworkMod" you mean CWM.zip right? This is a temporary recovery that disappears upon reboot. It also LETHAL to wipe with when running on top of a stock ICS kernel.
So to sum up;-
You were running Stock ICS.
You flashed CWM.zip (from YouTube or where ever) from stock 3e recovery and then flashed Root/busybox file.
Booted back into stock recovery, flashed CWM.zip again and performed wipe data/factory reset with it.
How am I going so far?
Bad news - you have most likely superbricked your device.
If so,new MOBO or repartition is only way out now
Click to expand...
Click to collapse
Yep, emmc bricked. Send it to servicecenter, they repaired it for free, for me. Or you can do the workaround http://forum.xda-developers.com/showthread.php?t=1667886 , but i dont would do that, as you will get many freezes maybe. Thats very annoying.
Regards

[Q] phone hanging at the start screen.

i was want just change my old recovery software, so i install TWRP recovery that time i facing this problem.
This worked out once, then I was trying another firmware, this didn't work out (phone was hanging at the Samsung GT-I9070 start-screen), so I thought: "OK, lets do the other firmware again".
So entered the download mode and tried to flash the "old" firmware again (XXLD1.tar) but it just does something very fast (not really installing) and reboots again with hanging at the start screen.
OK, so lets got to the "recovery-mode"... not possible!
Did this now a few times, but everytime the same result, just a quick full download bar and restarting with hanging.
Did I kill my phone?
ODIN look also fine...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> xxld1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> kernel.bin.md5
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
PLEASE HELP ME!!!

saha.gobinda89 said:
i was want just change my old recovery software, so i install TWRP recovery that time i facing this problem.
This worked out once, then I was trying another firmware, this didn't work out (phone was hanging at the Samsung GT-I9070 start-screen), so I thought: "OK, lets do the other firmware again".
So entered the download mode and tried to flash the "old" firmware again (XXLD1.tar) but it just does something very fast (not really installing) and reboots again with hanging at the start screen.
OK, so lets got to the "recovery-mode"... not possible!
Did this now a few times, but everytime the same result, just a quick full download bar and restarting with hanging.
Did I kill my phone?
ODIN look also fine...
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> xxld1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> kernel.bin.md5
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
PLEASE HELP ME!!!
Click to expand...
Click to collapse
if u r eble to boot u r phone in to download mode then its not being bricked i think u r not flashed file properly
Step-1: Download Android Jelly Beanofficial firmware for Samsung Galaxy S Advance to the computer
Step-2: Extract the downloaded zip file using Winzip, Winrzr, 7zip or any other extracting tool to get a file with .tar.md5 extension
Step-3: Download latest Odin software which will help to install the Jelly Bean firmware. Extract the Odin zip to getOdin exe
Step-4:Switch off the Galaxy S Advance and wait for five to six seconds for the vibration to confirm the power off
Step-5:Boot the phone into Download Mode by pressing and holdingVolume Down,HomeandPowerbuttons together. A warning screen will appear, now press theVolume Upbutton to continue to enter into Download Mode
Step-6:RunOdin.exe as an Administrator
Step-7:Connect the Galaxy S Advance to the computer using USB cable while the device is in Download Mode. Wait for some time until Odin detects the device. When the device is connected successfully, an Added message will appear under Odin. Also, the ID: COM box in Odinwill turn blue indicating all the drivers are installed successfullyNote:If theAddedmessage does not appear, then try the USB port at the back of the computer. In case Odin still fails to recognsie the device, then re-install USB driver.
Step-8:Click thePDAbutton and select the (tar.md5 file)
step-9: Verify that Auto Rebootand F.Reset Timecheckboxes are selected in Odin window. Also, ensure that the Re-Partition option is unchecked
Step-10:When everything is set, hit theStartbutton in Odin. The installation process should begin now and would take few minutes to complete
Step-11 once the installation process is completed, the phone will reboot automatically. And soon a PASS message with green background will appear in the extreme left box at the very top of Odin indicating successful installation.
phone get rebooted with samsung logo
Now safely unplug the USB cable from the phone to disconnect it from the computer
How to Fix Bootloop Issues
1) While installing the firmware if thePASSmessage does not display or the device gets stuck for a long time, then disconnect the phone from the computer. Remove the battery and re-insert it, check the USB connection, re-install the USB driver and disable KIES. Enter Download Mode and repeat the whole procedure.
2) If bootloop occurs or the device is stuck in welcome screen logo, then boot the phone into recovery mode. To do so, press and hold theVolume Up,HomeandPowerbuttons together. In recovery mode, perform data wiping task by selectingWipe data/factory resetthen selectWipe Cache Partition.Reboot the phone in normal mode by selectingreboot system now.When the phone boots up, it should be running on the official build. In recovery mode, useVolumekeys to scroll between the options and use thePowerbutton to select the particular option. Performing wiping task will erase the internal memory of the device.

Just flash firmware with odin, after it says "pass", remove cable and let your device boot and mostly (a.f.a.i.k) it doesn't boot, take out battery, go to recovery mode and wipe data/factory reset and after that reboot your phone.
sent with my S Advance

nalityta collect
Thank you very much my phone is now okay.......:laugh::good::angel:

saha.gobinda89 said:
Thank you very much my phone is now okay.......:laugh::good::angel:
Click to expand...
Click to collapse
just press thnx button if u can

Now i am facing another problem, my samsung galaxy s advance is 16 GBbut when i format my USB storage its show that 3.92 GB.....what can i do now. where is my rest of the storage 7 GB.......
PLEASE HELP ME.......

saha.gobinda89 said:
Now i am facing another problem, my samsung galaxy s advance is 16 GBbut when i format my USB storage its show that 3.92 GB.....what can i do now. where is my rest of the storage 7 GB.......
PLEASE HELP ME.......
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2096093

dimentl under
How to Update my samsung galaxy s advance gt i9070 16 GB Android jelly bean 4.1.2 to kitkat 4.4.2..... help me
give me solution in easy way....... plz help me

saha.gobinda89 said:
How to Update my samsung galaxy s advance gt i9070 16 GB Android jelly bean 4.1.2 to kitkat 4.4.2..... help me
give me solution in easy way....... plz help me
Click to expand...
Click to collapse
Just install CM11 zip from recovery. That is if the phone is I9070, and not I9070P.
Sent from my GT-I9070 using Tapatalk

shut_down said:
Just install CM11 zip from recovery. That is if the phone is I9070, and not I9070P.
Sent from my GT-I9070 using Tapatalk
Click to expand...
Click to collapse
i don't understand what you say plz give me better solution for this.....

saha.gobinda89 said:
i don't understand what you say plz give me better solution for this.....
Click to expand...
Click to collapse
Well, now can I ask? Is your device is Galaxy S Advance GT-I9070 series (not GT- i9070P series - NFC supports)? And has installed the official firmware 4.1.2+ (jelly bean)?
If your device is GT-I9070, and has installed the first official firmware 4.1.2+ (jelly bean). Then simply you do the installation via CWM Recovery which is certainly already installed on your device. after all these, then you can feel the sweetness of chocolate kitkat (CM11) style developers. Like what was mentioned by senior @shut_down before.

TPD-21 said:
Well, now can I ask? Is your device is Galaxy S Advance GT-I9070 series (not GT- i9070P series - NFC supports)? And has installed the official firmware 4.1.2+ (jelly bean)?
If your device is GT-I9070, and has installed the first official firmware 4.1.2+ (jelly bean). Then simply you do the installation via CWM Recovery which is certainly already installed on your device. after all these, then you can feel the sweetness of chocolate kitkat (CM11) style developers. Like what was mentioned by senior @shut_down before.
Click to expand...
Click to collapse
Yes, My device is Galaxy S Advance GT-I9070, 16 GB And has installed the official firmware 4.1.2+ (jelly bean). can you give proper download link kitkat (CM11) and give whole process by CWM method for install kitkat 4.4.2 or update version in my device.

saha.gobinda89 said:
Yes, My device is Galaxy S Advance GT-I9070, 16 GB And has installed the official firmware 4.1.2+ (jelly bean). can you give proper download link kitkat (CM11) and give whole process by CWM method for install kitkat 4.4.2 or update version in my device.
Click to expand...
Click to collapse
Look for CM11 bt TeamCanjica in original development section, put it in sd card, boot to recovery and install it with "update from external storage" or qhatever it was in stock recovery. Do factory reset and that should be it. If still not working go to cwm and wipe dalvik cache.
Sent from my GT-I9070

saha.gobinda89 said:
Yes, My device is Galaxy S Advance GT-I9070, 16 GB And has installed the official firmware 4.1.2+ (jelly bean). can you give proper download link kitkat (CM11) and give whole process by CWM method for install kitkat 4.4.2 or update version in my device.
Click to expand...
Click to collapse
Sorry I'm late replying. Yes, do as senior @shut_down mentioned above.
÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷
Sent From Glonass Satellite
÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷÷

kitkat install
shut_down said:
Look for CM11 bt TeamCanjica in original development section, put it in sd card, boot to recovery and install it with "update from external storage" or qhatever it was in stock recovery. Do factory reset and that should be it. If still not working go to cwm and wipe dalvik cache.
Sent from my GT-I9070
Click to expand...
Click to collapse
please give me download link CM11 or kitkat 4.4.2 install software.

saha.gobinda89 said:
please give me download link CM11 or kitkat 4.4.2 install software.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2578599

thanks
shut_down said:
http://forum.xda-developers.com/showthread.php?t=2578599
Click to expand...
Click to collapse
Thanks Man....

Kitkat rom
shut_down said:
http://forum.xda-developers.com/showthread.php?t=2578599
Click to expand...
Click to collapse
which one is best for Samsung galaxy S advance Cyanogenmod_Kitkat ROM or Omni_Kitkat ROM Please tell me and which is battery support will be good. if think that any of them one good then give me download link. pls help me.

saha.gobinda89 said:
which one is best for Samsung galaxy S advance Cyanogenmod_Kitkat ROM or Omni_Kitkat ROM Please tell me and which is battery support will be good. if think that any of them one good then give me download link. pls help me.
Click to expand...
Click to collapse
You should try yourself. It depends on your usage. And there is no such thing as best rom. You have our development and original development sections and look there.
Sent from my GT-I9070

looking for kitkat
shut_down said:
You should try yourself. It depends on your usage. And there is no such thing as best rom. You have our development and original development sections and look there.
Sent from my GT-I9070
Click to expand...
Click to collapse
where i looking.... give me download link...

Not solved bootloop (i've really tried)

Hello everyone.
My baseband was missing after flashing latest Maclaw's CM11 so i decided flash a new baseband from this thread http://forum.xda-developers.com/showthread.php?t=2526831 After i flashed and got NO error from Odin, my phone ended in this infernal bootloop where it shows the samsung model of the device (Samsung galaxy s3 mini gt-i8190) and then it turns off, vibrates and starts over again, however i'm able to access both download and recovery mode.
I've flashed untouched stock ROM from sammobile and rooted stock ROM from this thread http://forum.xda-developers.com/showthread.php?t=2030282 after doing that i either factory reset myself via recovery or flashed the WIPE.tar followed by the PARAM.tar file also in the thread above. No success. I have also tried to flash back to maclaw's cm11 with TWRP or CWM and factory reset from these custom recoveries instead of stock recovery but it doesn't work.
Last time i checked my battery (from TWRP menu) it was 15% but when i plug my phone off to the charger it starts bootlooping so i don't think it is able to charge.
So i don't know what else i can do, if there's something that can be done at this point, i was thinking to pay for technical service but there's really something to be done? i don't want to lose my phone AND my money.
I'll appreciate any guidance or help this awesome community could offer, thanks in advance.

Last way out:
Download This rom "I8190 серв. укр.rar" from here.
Unpack .rar and open Odin.
Select the goldenxx.pit to [PIT]
CODE_I8190XXAMA2_809600_REV00_user_low_ship.tar.md 5 to [PDA]
CSC_QXE_I8190QXEAMA1_20130109.163004_REV00_user_lo w_ship.tar.md5 to [CSC]
Put your phone in download-mode and connect it to computer.
Hit [Start] when device is detected by Odin.
You will end up with a "La'Fleur" branded phone, but no worries!
Just go to download mode again and flash your choice of firmware.
Then flash the baseband of your choice.
The three button combo will still work!!
Click to expand...
Click to collapse
moonryder
p.s. this is not my work, i took it from my bro @tys0n from this thread.

moonryder said:
Last way out:
moonryder
p.s. this is not my work, i took it from my bro @tys0n from this thread.
Click to expand...
Click to collapse
Now i remember i also tried flashing that ROM
i get this, i don't know why:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CODE_I8190XXAMA2_809600_REV00_user_low_ship.tar.md5 is valid.
<OSM> CSC_QXE_I8190QXEAMA1_20130109.163004_REV00_user_low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.

Check your partitions with TWRP recovery (make sure partitions are there and they work fine (You can try mounting it and open twrp file manager)) and try to change filesystem to ext4 (Maclaw Roms changes it to f2fs) and, if anyone already has ext4 format, do a format again and flash stock rom with Odin.
Do you have a .pit for your phone?

LuuchoRocha said:
Check your partitions with TWRP recovery (make sure partitions are there and they work fine (You can try mounting it and open twrp file manager)) and try to change filesystem to ext4 (Maclaw Roms changes it to f2fs) and, if anyone already has ext4 format, do a format again and flash stock rom with Odin.
Do you have a .pit for your phone?
Click to expand...
Click to collapse
Sorry, could you be more specific? How exactly do i check my partitions with TWRP recovery and how to change my filesystem?
I do not have any .pit for my phone neither.

2112212 said:
Sorry, could you be more specific? How exactly do i check my partitions with TWRP recovery and how to change my filesystem?
I do not have any .pit for my phone neither.
Click to expand...
Click to collapse
To check your partitions, almost, you must mount them and check if there have any files...
To mount, select mount:
http://img.wonderhowto.com/img/36/7...ur-htc-evo-4g-lte-using-twrp-supersu.w654.jpg
And after in twrp advanced options select file manager:
http://cloud.addictivetips.com/wp-content/uploads/2013/05/TWRP-Recovery-Advanced.jpg
A pit file contains info of "partition table" and can help you to do a repartition of your phone mmc

[Q] Help me please

Hello new in this forum.....
The threads I read overwhelmed me.... :cyclops:
I have a N7000 from a friend of mine. It had a dedicated 4.0.4 rom from "3" (italian operator) build IMM76D.XXLRL
I tried to install a new italian rom 4.1.2 via odin but every attempt failed
Unfortunately I ended up into a thread about ICS kernel (sorry if I make some mistakes with names but I'm really lost....)
so downloaded the ICS and with my surprise it was installed into the phone.
From that moment the N7000 hang at samsung logo with the yellow triangle....
And the worst thing It goes in download mode but not in recovery mode.....
I tried to read many post before write, trying to understand waht to do but now I'm totally confused..... md5,tar,img, zip...... kernel,root, cwm., rom ....
Someone may explain to me if there is something to do to save the phone?
Thanks i n advance
Andrea

andrew59it said:
Hello new in this forum.....
The threads I read overwhelmed me.... :cyclops:
I have a N7000 from a friend of mine. It had a dedicated 4.0.4 rom from "3" (italian operator) build IMM76D.XXLRL
I tried to install a new italian rom 4.1.2 via odin but every attempt failed
Unfortunately I ended up into a thread about ICS kernel (sorry if I make some mistakes with names but I'm really lost....)
so downloaded the ICS and with my surprise it was installed into the phone.
From that moment the N7000 hang at samsung logo with the yellow triangle....
And the worst thing It goes in download mode but not in recovery mode.....
I tried to read many post before write, trying to understand waht to do but now I'm totally confused..... md5,tar,img, zip...... kernel,root, cwm., rom ....
Someone may explain to me if there is something to do to save the phone?
Thanks i n advance
Andrea
Click to expand...
Click to collapse
so, what is your question actually??

Mate, I think the question is simple.
From what I understand in your comment, it seems you tried to install the Stock Rom 4.1.2 Italy, when you were the 4.0.4 / 4.0.3 Stock Rom Italy. On installation through ODIN pc you had a problem where it remains in the Samsung logo, will not let you enter the Recovery mode, only the Download mode. Is that so?
I should arrived that case do not leave any triangle would remove the battery, and after 10-15 seconds reintroduce it, and just then press buttons to enter the Recovery mode. If it fails, repeat the removal of the battery, but now when placed connect the DC charger to the phone I tried to turn normally to 20-25 seconds (just outside and away the logo of battery charging), and try to turn it on Recovery mode again, but we will keep down so long that should disappear all as to turn it off, and you press the keys for the Recovery mode, this time releasing anything else lighting appear on the screen, just a moment before letters GT-N7000, now if it really is accessible Recovery should apparate.
If you enter Recovery Mode Stock Samsung, you will have look out if a line appears below indicating the application, or wondering whether to apply the new CSC, we accept without thinking, since it must reaffirm the phone to initiate a Stock Rom.
Now if I come to this moment really was not accessible Recovery mode should get a screenshot of ODIN pc which finishes entering files to mobile, if it were really a fault, and do not leave do the installation, if you checked any box incorrectly, of which are not activated.
Other options include USB cable failure, USB port, lack of USB debugging enabled before starting the installation, do not put at least 10 minutes in the backlight time (this can try to fix running a finger across the screen every 23 seconds if it was 30 seconds off), but that the capture can determine ourselves if the error is only for ODN pc, which can be a failed in the installation and have not really finished the installation, in this case it would be almost insurance problem USB cable used, and in extremis or USB port.

fusionero said:
Mate, I think the question is simple.
From what I understand in your comment, it seems you tried to install the Stock Rom 4.1.2 Italy, when you were the 4.0.4 / 4.0.3 Stock Rom Italy. On installation through ODIN pc you had a problem where it remains in the Samsung logo, will not let you enter the Recovery mode, only the Download mode. Is that so?
I should arrived that case do not leave any triangle would remove the battery, and after 10-15 seconds reintroduce it, and just then press buttons to enter the Recovery mode. If it fails, repeat the removal of the battery, but now when placed connect the DC charger to the phone I tried to turn normally to 20-25 seconds (just outside and away the logo of battery charging), and try to turn it on Recovery mode again, but we will keep down so long that should disappear all as to turn it off, and you press the keys for the Recovery mode, this time releasing anything else lighting appear on the screen, just a moment before letters GT-N7000, now if it really is accessible Recovery should apparate.
If you enter Recovery Mode Stock Samsung, you will have look out if a line appears below indicating the application, or wondering whether to apply the new CSC, we accept without thinking, since it must reaffirm the phone to initiate a Stock Rom.
Now if I come to this moment really was not accessible Recovery mode should get a screenshot of ODIN pc which finishes entering files to mobile, if it were really a fault, and do not leave do the installation, if you checked any box incorrectly, of which are not activated.
Other options include USB cable failure, USB port, lack of USB debugging enabled before starting the installation, do not put at least 10 minutes in the backlight time (this can try to fix running a finger across the screen every 23 seconds if it was 30 seconds off), but that the capture can determine ourselves if the error is only for ODN pc, which can be a failed in the installation and have not really finished the installation, in this case it would be almost insurance problem USB cable used, and in extremis or USB port.
Click to expand...
Click to collapse
Thanks to reply.....
I was not really clear probably.
I tried to install 4.1.2 over 4.0.4 dedicate rom (3 H3G italian operator)
Odin always failed hanging or giving some fault
So I installed the ICS kernel (or rom) everything was fine. So I suppose the cable is ok , odin is ok etc....
But from the moment I downloaded the ICS, at reboot the phone hang on samsung logo with yellow triangle. ANd if I try to switch off the phone it restart and hang on logo.
Download mode is still working but recovery mode not.....
I'm looking for some kernel, rom, cwm to download, to recover the phone.....

The best thing to do is reinstall the ROM 4.1.2 (the 4.0.x are more dangerous if we wipes, JellyBean when they are not), but check that no error appears, if it appears only after installing the Rom rather fails during it, you can download the kernel Philz for you version, right now if you tell me the link to SamMobile I can tell you what, so you can tell which is correct, although it is not hard to tell if you look at the post of Philz above kernel with all links to them. After installation and download the kernel, you turn the phone into Recovery mode, you select mount usb (I think it came out well, but stresses) and connect your phone to your pc, you can pass the kernel to the internal SD and another copy to the SD external (remember to leave both copies at the root of both SD's). You MUST complete the transfer and disassemble with the option displayed on screen, and disconnect the USB cable. You continue by going to install zip, and should be able to select the Kenel Philz to install, after installing (if you get an error: Status 7 quiet, it was not the correct version of the kernel, and not actually installed), you will have to restart the mobile again, but when you start on with the letters GT-N7000, you will have to restart it by pressing Vol + - Power - Home, all at once, and keep it until the letters again, and keep it until it goes - restart, then you press the 3 keys, and when the letters appear, you must drop the 3 keys, and should you appear the menu Recovery kernel Phliz, there as you will see below something that says CSC implemented or instead ask if you want to apply, accept if you ask, and you should be able to restart the phone and wait about 5 minutes maximum to emit sound and vibration as it is booting at all, and then you should be able to start getting bills from Samsung and Google.

Thank fusionero
the problem is I'm not able to install the 4.1.2 , odin hang or fail
The ROM version I need is
sammobile.com/firmwares/download/22314/N7000XXLT9_N7000ITVLT3_ITV
So I think nex step is to install kernel Philz but I don't know which version I need. On the phone was installed 4.0.4 build IMM76D.XXLRL
CIAO

You must enter this http://www.sammobile.com/firmwares/download/22314/N7000XXLT9_N7000ITVLT3_ITV.zip/ address, and you must connect to you account to download that version you mention, I just check and this downloading smoothly on my pc . The problem is that it would open without ending .zip or you caught hours of server failure, just that i found this morning when downloading another who asked me.
As to what you mention about the version you have installed, as you are looking at the correct thread ( http://forum.xda-developers.com/showthread.php?t=1901191 ), the kernel you need for what you indicate ( 4.0.4 build IMM76D.XXLRL CIAO ) is this:
Update to all ICS 4.0.4 kernels from 3.71 ---> 3.99:
http://www.mediafire.com/?3ale6m9q6b6a3
Updated kernels list:
PhilZ-cwm6-BULR1-SWC-v3.99
PhilZ-cwm6-DDLR6-ODD-v3.99
PhilZ-cwm6-DDLR9-INU-v3.99
PhilZ-cwm6-DDLRB-ODD-v3.99
PhilZ-cwm6-DXLP9-OLB-v3.99
PhilZ-cwm6-DXLR2-OLB-v3.99
PhilZ-cwm6-DXLR5-OLB-v3.99
PhilZ-cwm6-JPLPD-OJP-v3.99
PhilZ-cwm6-JPLR8-OJP-v3.99
PhilZ-cwm6-UBLPC-UUB-v3.99
PhilZ-cwm6-UBLR3-PSN-v3.99
PhilZ-cwm6-UBLR5-TCE-v3.99
PhilZ-cwm6-XXLPY-XEN-v3.99
PhilZ-cwm6-XXLQ3-OXX-v3.99
PhilZ-cwm6-XXLRG-DBT-v3.99
PhilZ-cwm6-XXLRI-AUT-v3.99
PhilZ-cwm6-XXLRK-XEU-v3.99
PhilZ-cwm6-XXLRL-HUI-v3.99 - Is this your kernel
PhilZ-cwm6-XXLRQ-DBT-v3.99
PhilZ-cwm6-XXLRT-DBT-v3.99
PhilZ-cwm6-XXLRU-VDI-v3.99
PhilZ-cwm6-XXLRW-SFR-v3.99
PhilZ-cwm6-ZSLPF-OZS-v3.99
PhilZ-cwm6-ZSLPM-OZS-v3.99
PhilZ-cwm6-ZSLPN-OZS-v3.99
Click to expand...
Click to collapse

andrew59it said:
Hello new in this forum.....
The threads I read overwhelmed me.... :cyclops:
I have a N7000 from a friend of mine. It had a dedicated 4.0.4 rom from "3" (italian operator) build IMM76D.XXLRL
I tried to install a new italian rom 4.1.2 via odin but every attempt failed
Unfortunately I ended up into a thread about ICS kernel (sorry if I make some mistakes with names but I'm really lost....)
so downloaded the ICS and with my surprise it was installed into the phone.
From that moment the N7000 hang at samsung logo with the yellow triangle....
And the worst thing It goes in download mode but not in recovery mode.....
I tried to read many post before write, trying to understand waht to do but now I'm totally confused..... md5,tar,img, zip...... kernel,root, cwm., rom ....
Someone may explain to me if there is something to do to save the phone?
Thanks i n advance
Andrea
Click to expand...
Click to collapse
Your phone is not booting since you flashed an ICS kernel over a JellyBean ROM
Android ICS version : 4.0.4
Android JB version : 4.1.2
so I hope you understand the difference.
You are lucky you didn't brick your device or have you already
But since you are able to go in download mode I think its not bricked yet.
It was probably a bad download which failed the installation so download ROM again and this time verify that your download is not corrupt by running it via md5 if provided.
also please provide the link of the ROM thread that you are trying to install so that I can understand better
and if you are not looking to flash a custom ROM or rooting your device in order to do so then in that case the steps are pretty straight forward
download Stock ROM
extract ROM
open Odin
select appropriate files i.e Choose CODE in PDA, MODEM in PHONE, Multi CSC in CSC
put phone in download mode and connect
the bar should turn yellow once connected.
once connected click on flash
bar should turn green if successful
REVENGE SOLVES EVERYTHING

tysonraylee said:
Your phone is not booting since you flashed an ICS kernel over a JellyBean ROM
Android ICS version : 4.0.4
Android JB version : 4.1.2
so I hope you understand the difference.
You are lucky you didn't brick your device or have you already
But since you are able to go in download mode I think its not bricked yet.
It was probably a bad download which failed the installation so download ROM again and this time verify that your download is not corrupt by running it via md5 if provided.
also please provide the link of the ROM thread that you are trying to install so that I can understand better
and if you are not looking to flash a custom ROM or rooting your device in order to do so then in that case the steps are pretty straight forward
download Stock ROM
extract ROM
open Odin
select appropriate files i.e Choose CODE in PDA, MODEM in PHONE, Multi CSC in CSC
put phone in download mode and connect
the bar should turn yellow once connected.
once connected click on flash
bar should turn green if successful
REVENGE SOLVES EVERYTHING
Click to expand...
Click to collapse
Thanks everyone....
I think you hit the problem..... but my original ROM version was 4.0.4 .... (H3G)
Anyway probably something went wrong.... I don't need a custom ROM or to root the device.
I need to install N7000XXLT9_N7000ITVLT3_ITV if possible but the flash doesn't start via ODIN
May you explain step by step what have I to do? I really appreciate....
What do you mean "select appropriate files i.e Choose CODE in PDA, MODEM in PHONE, Multi CSC in CSC" ?
md5 is not a single file? I read something about more files to place in odin.....
@ fusionero: I already downloaded the files.... also PHILZ XXLRL but the device doesn't start anyway.....

andrew59it said:
Thanks everyone....
I think you hit the problem..... but my original ROM version was 4.0.4 .... (H3G)
Anyway probably something went wrong.... I don't need a custom ROM or to root the device.
I need to install N7000XXLT9_N7000ITVLT3_ITV if possible but the flash doesn't start via ODIN
May you explain step by step what have I to do? I really appreciate....
What do you mean "select appropriate files i.e Choose CODE in PDA, MODEM in PHONE, Multi CSC in CSC" ?
md5 is not a single file? I read something about more files to place in odin.....
@ fusionero: I already downloaded the files.... also PHILZ XXLRL but the device doesn't start anyway.....
Click to expand...
Click to collapse
Did you download the XXLT9 ROM?? or the ROM that you want to flash ??
if so then it should be a zip file, if you extract that zip file you should have 3 files in it (sometimes only PDA file is present and the other two i.e Modem and CSC are not present, dont worry the PDA file alone is enough)
Open Odin, click on PDA button and select the firmware file with .tar.md5 extension (The firmware file look something like: N7000XXDLJ5_N7000ODDDLI7_INU.tar.md5 Select the one that looks similar to the ROM you downloaded)
and if there are CSC and Modem files then select them by clicking Phone and CSC in Odin accordingly. It will be mentioned in the file name if its a Modem or CSC file
if MODEM_XXXX.tar.md5 then select that file by clicking the PHONE in Odin and if XXXX_CSC_XX.tar.md5 then select it by clicking CSC in Odin
remember that you lose all your data
Then just click flash and it should flash
md5 is a single file and is used to check the integrity of the file you downloaded. Its just used to make sure that the file you downloaded doesnt have any errors or is corrupt. you use the .md5 file and compare it with the md5 of the ROM.zip If it matches then its not corrupted or is a bad download. (.tar.md5 and .md5 are different files as in .tar.md5 is a firmware file and .md5 is a hash file used for integrity check)
Just right-click the rar/zip file and select properties and select the "file hashes" tab and if you downloaded a .md5 open that file by clicking "compare file" in the same tab
.md5 is always provided along with file you downloaded and its size is always in kbs , if its not provided then you cant do the hash check
If you dont have "file hashes" tab after right-clicking and selecting properties of the rar/zip file then you should download and install HashTab to get that option
follow this video for a better understanding https://www.youtube.com/watch?v=Ulz-1UYzHBA
the process is same but you should use your ROM files i.e Italian N7000 files to flash your phone and yes Odin version doesnt matter, you can use any version

Hello
I downloaded N7000XXLT9_N7000ITVLT3_ITV.ZIP
Extracted the file into a folder and had N7000XXLT9_N7000XXLT3_N7000ITVLT3_HOME.tar.md5 (there is also SS_DL.dll)
Tried to flash the md5 file with odin (V.1.85) , but odin returns a fail.....
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLT9_N7000XXLT3_N7000ITVLT3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

andrew59it said:
Hello
I downloaded N7000XXLT9_N7000ITVLT3_ITV.ZIP
Extracted the file into a folder and had N7000XXLT9_N7000XXLT3_N7000ITVLT3_HOME.tar.md5 (there is also SS_DL.dll)
Tried to flash the md5 file with odin (V.1.85) , but odin returns a fail.....
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLT9_N7000XXLT3_N7000ITVLT3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> cache.img
<ID:0/007> NAND Write Start!!
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
did you follow the video??
did you select N7000XXLT9_N7000XXLT3_N7000ITVLT3_HOME.tar.md5 by clicking PDA??
REVENGE SOLVES EVERYTHING

Yes of course.....

andrew59it said:
Yes of course.....
Click to expand...
Click to collapse
still odin fails?? even after following the video??
are you using the original cable to flash ??
try plugging the cable into a different usb port and flash

Yes it fails
I will try with another cable and port. But if I flash Philz rom it works.....

andrew59it said:
Yes it fails
I will try with another cable and port. But if I flash Philz rom it works.....
Click to expand...
Click to collapse
after trying that try the solution from this post http://forum.xda-developers.com/showthread.php?p=41844601#post41844601
and also try and follow the thread as people have posted different solutions regarding your problem
Also this would be the extent of help i can provide
if that doesnt work i dont know what will
So please forgive me for not being able to help any further :angel:

maybe you should use odin3 v3.04 or v3.09.
usually i use odin3 v1.8X for multiple file roms but in your case, you have only One-file rom.
---------- Post added at 01:12 PM ---------- Previous post was at 01:09 PM ----------
besides, extract all the files in odin archive and place them in one folder dont just start the odin .exe file directly from the archive.

Hello changed the cable the port and ODIN (ver 3.04)
The same problem..... look at the picture attached....
I'm loosing hope.....:crying:

Thanks to all....
solved the problem!!! WOW! :good::victory:
The solution was to change pc, I went on my girlfriend laptop and everything went smooth as silk.....
Thank you all to supporting me !!

andrew59it said:
Thanks to all....
solved the problem!!! WOW! :good::victory:
The solution was to change pc, I went on my girlfriend laptop and everything went smooth as silk.....
Thank you all to supporting me !!
Click to expand...
Click to collapse
congrats
REVENGE SOLVES EVERYTHING