I have a familiar problem we've all read about but my instance seems to be a bit different than anything i've found when searching the forums. Heres the Details.
I have a Tilt, I'm running Dutty's WM6.1. I've been running it for weeks and all is great. recently bought a usb car adapter. plugged it in and the phone lit the red light of doom and shut down. i soft reset...same problem. so I left it alone. Now my TILT turns on fine, operates fine. boots in a timely fashion but will not recognize any USB cord i've plugged in. I've tried many. However it WILL charge when the power is turned off. the red light is lit while charging but it charges.
and in case it helps anyone...the bootloader does say SERIAL and no usb.
I've seen lots of different instances of this issue on the forum search but they all were a little different from my situation or an answer was never given in the thread. Thank you to any one who knows the secret to this or has a solution that works.
Seems you fryed some part of your USB port. You should send it in to AT&T if you're under warrenty. If not, best thing is to replace it by solderng a new USB port.
Kraize
Since you can still turn it on and all seems relatively normal why not back up your data and try a Hard Reset ?
You may not have bricked it...may I ask which USB car charger you bought so I can avoid it ?
I doubt the physical USB jack is damaged, anythings possible but it's more likely worse than that IF it is not software/rom related.
Hope you solve it cheaply !
are you trying to charge it with the one that came with the kaiser?
Okay, first thing to mention is that I have searched for information on my issue and while I have found (and tried) solutions that approach my goof, I need to post this:
Last night I finished reading from Kindle app, hit the power button to shut off the screen and laid it down. I know I should have plugged it to recharge but too late now. I am running CM nightly from 07172012, so I know I didn't download the nightly CM battery issue versions.
This morning the screen will not light up; I have tried charging it, hard reset with power and home screen buttons for 15-20 seconds (and longer), and nothing works. My concern is that the screen is dead. I connected the touchpad to my laptop and I get the connection sound from the laptop; it sees the TP but does not accept it as a portable storage device. Device Manager lists it as: QHSUSB_DLOAD with driver(s) not loaded.
When I try the volume rocker button I do not hear the small audible ping as volume goes up or down. Of course, with the resets, who knows where I am in the OS (or even if it is WebOS or Android).
I really didn't want to be a noob and post this, but I need some advice from the brethren here on XDA. Thanks in advance.
It seems to me that it's not even booting if your getting that strange device in device manager. Try the webos recovery tool from hp. It may help. Although it will wipe android off.
Sent from my SGH-I777 using xda app-developers app
my son-in-law is in the same boat. Nothing he does wakes it up. I believe there are tp's out there with this hardware issue. I let my tp battery drain completely. It powers down around 4% battery. I place it on the touchstone, it charges backup and boots into moboot, then webos. I've done this twice. no problems. If it's under warranty still, send it in.
If you have a touchstone charger put it on that and leave it for a couple of hours and it Will come back to life.
See this article by Reverend Kyle http://www.reverendkyle.com/index.php/articles/146-hp-touchpad-charging-issues-solution
I hope this helps.
I've had multiple instances of black screen of death failure.
The latest one I had, I was able to restore by using a standard USB to micro USB cable (and recently NOT the HP OEM cable) to connect to the computer I usually use to sync or use HP web doctor with.
Same symtpom as the OP, get the three dings when connecting the touchpad to the computer, no responses and the QHUSB driver load error. HP charger wouldn't chage it, touchstone would not charge it.
Anyhow, I left it connected for a few hours to charge connected to my PC. Then, I disconnected from the PC using the large USB connector and reconnected. Whamo, got to the bootloader.
I believe what happened was I trickle charged the touchpad enough to get the touchpad to boot.
You can try the various hard boot keypresses too, but wait for a few hours while trying to trickle charge the touchpad via the computer USB.
Update
Okay, so I followed the old rule of doing the simple (and/or free) solutions first and then move on.
1) I set the touchpad on the touchstone for several hours yesterday - no luck
2) I connected the touchpad to my pc through the USB and let it charge - no luck
3) I let it be plugged into the standard charging plug all night - no luck
4) I prayed to the great old god Cthulhu - no luck
My only option remaining is to use WebOS Doctor. One question on that: in all the literature I have read thus far (and perhaps I am mistaken), I need to be able to get the TP into USB mode to download the corrections/reboot back into WebOS. Is that right or can I expect that when the doctor sees the mangled mess of an OS through the USB connection, it will know what to do?
Again, as always that for the previous posts and for the support.
mnachazel said:
Okay, so I followed the old rule of doing the simple (and/or free) solutions first and then move on.
1) I set the touchpad on the touchstone for several hours yesterday - no luck
2) I connected the touchpad to my pc through the USB and let it charge - no luck
3) I let it be plugged into the standard charging plug all night - no luck
4) I prayed to the great old god Cthulhu - no luck
My only option remaining is to use WebOS Doctor. One question on that: in all the literature I have read thus far (and perhaps I am mistaken), I need to be able to get the TP into USB mode to download the corrections/reboot back into WebOS. Is that right or can I expect that when the doctor sees the mangled mess of an OS through the USB connection, it will know what to do?
Again, as always that for the previous posts and for the support.
Click to expand...
Click to collapse
Another piece of black magic that worked for me and is worth a try as it is free. Connect Touchpad to standard HP brick charger plugged into power outlet. Unplug cable from charger, count to 5, plug it back in, count to 5, take it back out. Repeat the cycle until you get bored or until you get a red charging symbol. If you get the latter then let it charge up normally and you are back in business. The theory behind this method is that it takes a few seconds on plugging in for the circuits to realise they "shouldn't be charging" and this allows a little bit of charging to take place on each insertion. Repeat enough times and you get enough to kick start the proper charging. In my case about 20 times did the trick.
As I didn't want to get into this situation again I then set up a Tasker process to power down th eTouchpad if the battey charge dropped below 8% and I've been OK since.
RIP Touchpad / EOT
Well, I had to wait a day to get my hands on a WinXP laptop; I upgraded my Dell to Win8 about 3 months ago and WebOS Doctor does not play well with Win8.
While that time passed, the touchpad finally gave up the ghost. There is no power left in the TP. When I run WebOS Doc the laptop cannot see the TP connecting via USB. I also checked by connecting the TB to the Dell, since it would at least see the device. Not any more.
My thanks again to those that responded. I did try the plug in, plug out with 5 second waits between, just in case. You never know. However, after 50+ attempts I had to call it a no-go.
does your home button light come on at all? Are you able to see moboot bootloader at all or are you able to start the tablet in webos recovery mode by holding the vol key while powering it on? are you able to ./adb connect? Also I've never had much luck with the resest method youre using, holding down the power and home key, I always hold down the power key and press the home key 15 times, when I get hard freezes and lockups, it's always worked.
Mine is in the same boat for a couple of months, removed battery and charged. Boot loader is borked I get only get a qualcomm usb device but nothing thats of any use for webos doctor or qualcomm tools. We'll have to wait until someone figures out jtag or how to replace the bootloader with qualcomm tools. I'm amazed with the number of touchpads out there that something hasn't leaked from hp to fix it. Anyone got friend in hp or qualcomm :angel:
OP Update
Well, I thought this was a dead issue but here is the latest.
After wallowing it a pit of despair the likes of which can only be described as wretched, (I even coveted my wife's TP up close, almost giving into temptation and swapping decals to reverse ownership) I looked outside of XDA and did general Google searches and happened upon this site:
http://forums.webosnation.com/hp-touchpad/299256-dead-touchpad.html
After reading a bit I realized that the touchstone may be able to recharge the dead battery even though fully drained. I began the quest that Friday morning the 24th of August, after verifying that my Dell laptop did not see the TP when plugged in via the USB cable.
I just did a quick check and the laptop now "sees" the TP when connected. Still no luck on booting into Moboot or the USB icon screen - neither Power and Volume Up or Power and Home buttons achieve anything. But I am glad to see that the touchstone has placed enough charge into the battery that the laptop is aware of the TP when connected.
I believe that given a few more days on the touchstone I should be able to boot into moboot.
@ haxin - I have nothing. Not a single light from the Home button - my only evidence that there is SOMETHING going on is when I connect the TP to the laptop and get my connection "sound". Again, I have high hopes that the touchstone will get me where I am going, albeit at a snails pace.
@ paddy - Yeah, I hope that when (if) I get to a lit screen, I am able to move past where you are at. My big concern is that I am toast even with a semi charged or fully charged battery from the touchstone.
I will update later on. Again, thanks to all for the input and probing questions. You have made me think harder and work a bit longer on this project.
OP Update - 31 August
After 7 days on the touchstone, the touchpad is currently showing the low battery charge icon; I have now plugged it into the A/C adapter.
Each morning I have picked up the TP, held down the power button and held the home button for 15+ seconds. Today it worked, turning on the screen for the first time in a week and letting me see the low battery image.
In my quest to resolve this issue, I have read so many variations on what buttons to hold and how long to hold them that after awhile you end up considering the possibility that SOME of the button options are not correct. That the operator has booted their TP up, but they misconstrued the actual solution; how else can you explain the idea that HP built so many different button combinations and hold times to boot a TP from a nearly or fully dead battery state?
Anyway, I will continue to post updates until my beloved TP is back to running CM9.
And to all those who gave their TP up because the battery got too low; find a touchstone or other "trickle" charger solution, connect and let it sit for a week or so.
Thanks!
Glad the Touchstone worked for you , don't know why it has taken so long to charge but when your up an running properly Llama is a good app to install as
A:You can set alarms for when the battery gets to a certain level/levels
B:Have it shut down when the battery gets to a certain level.
I use 20% for an alarm and 10% to shut down which allows me to sleep easy and not worry if someone else is using it . .
I am up and running. I most definitely will load that app on my TP, plus my wife's and a coworker who bought a TP because of mine.
I don't know either why it took so long; I am just glad it worked and I have it back. I am on it right now.
Thanks again to all who provided feedback and guidance. This is why I love XDA.
Sent from my HP Touchpad using xda app-developers app
HP Touchpad sleeping and will not turn on
Just a note to those HP tablet owners who experience the Black screen of death or sleep of death.
I am the proud owner of 4 HP tablets and two of them so far have had the black screen of death. I have read forum after forum trying to get answers to this problem. There was only one posting that has made cense to me. Someone posted that the tablets symptoms are very much like when the Phones use to go to sleep. The solution was to disconnect the battery for a few minutes then plug it back in. Then simply hit the hold the power button down to turn on the tablet.
The problem is taking the TP apart. There is a video on youtube on how to disassemble the tp. It is a little annoying that you have to go to such lengths to reset the hardware but HP will charge you 250 dollars to fix the problem. After you watch the video on how to open the TP, remove the 3 little screws holding the battery. Now slowly pry the battery up, they use double sided tape to hold it in place along with the screws. Wiggle the battery side to side and try to disconnect the battery connector. This can be done without removing the boards in the TP. Wait 1 min then try to replace the connector in the socket. It is on the underside of a board so when you have it in place use something to make sure it is tight. Plug the charger in to the USB cable. Without closing up the unit hold the tablet power button in until you get the battery charging symbol on the display. Let the unit charge while it is still disassembled. Just in case you have a problem. Once everything is operating disconnect to charger and replace the battery screws, now snap everything together.
This was the only way I was able to fix two of my four TP's. I am sure I will have to do this again because my kids always let the tablets go dead and they don't pay attention when placing them on the Stone for charging. If the tablet is not properly placed on the stone the tablet will not charge.
Hope this helps.
This by far is the best tablet for the money anywhere.
msousa1 said:
Just a note to those HP tablet owners who experience the Black screen of death or sleep of death.
The solution was to disconnect the battery for a few minutes then plug it back in. Then simply hit the hold the power button down to turn on the tablet.
The problem is taking the TP apart. There is a video on youtube on how to disassemble the tp. It is a little annoying that you have to go to such lengths to reset the hardware but HP will charge you 250 dollars to fix the problem. After you watch the video on how to open the TP, remove the 3 little screws holding the battery. Now slowly pry the battery up, they use double sided tape to hold it in place along with the screws. Wiggle the battery side to side and try to disconnect the battery connector.
Click to expand...
Click to collapse
I realise this is an old thread, but I recently had a reoccurrence of the black screen of death issue and thought given the number of touchpads still out in the wild, I would share my experience on the off-chance it may help somebody.
My first experience of the black screen issue was a few months after having my touchpad (many years ago). The screen just went black and no combination of holding the reset keys for any period of time would restart the unit. I had suffered lock-ups before and found the reset combination to be successful, but this time none of that worked and I had effectively what appeared to be a dead unit.
Having contacted HP, I returned the unit under warranty and a unit was returned working. I say “a unit” as I was never quite sure if it was the same unit or a refurbed unit, but to be honest given the speed the units went out of stock during the fire sale, I was just glad to have a working unit again.
Well this week after several years of use including the installation of Android, the black screen occurred again. As before, no combination of the keys / holding for a period of time / pressing them a number of times etc had any effect. The unit was three quarters charged and I was using it up till the point the screen went black. :crying:
Given that the unit has no warranty and it was “dead” anyway, I decided to take it apart. Despite watching YouTube videos, this appeared to be more troublesome than I thought, but eventually I was in. Interestingly, the backlight on the screen was still lit, suggesting the unit was still powered. I did consider disconnecting the battery, having removed the screws as per the previous poster, but mine seemed to be well and truly stuck down and I felt I may damage it prying it away from the base.
However, looking around inside the unit, I spotted what was clearly a surface mounted switch that faced upwards towards the back of the screen. Out of interest, I pressed on this switch with my finger nail and my unit powered off (shown by the backlight turning off). I then pressed the normal power switch and the unit powered up as normal. I have attached a photo of the switch which resides close to the popout tab with serial numbers on that can be found on the right hand side of the unit.
It does appear strange that HP put this “reset” button inside the unit, facing inwards rather than outwards where a small hole in the back of the case could be used to press it. So if you do get to the opening the case stage, consider this as an alternative to prying the battery loose. Also if somebody can work out a way to make the button accessible from outside the case it might be a useful modification.
JoeG90 said:
<.......................................>
However, looking around inside the unit, I spotted what was clearly a surface mounted switch that faced upwards towards the back of the screen. Out of interest, I pressed on this switch with my finger nail and my unit powered off (shown by the backlight turning off). I then pressed the normal power switch and the unit powered up as normal. I have attached a photo of the switch which resides close to the popout tab with serial numbers on that can be found on the right hand side of the unit.
It does appear strange that HP put this “reset” button inside the unit, facing inwards rather than outwards where a small hole in the back of the case could be used to press it. So if you do get to the opening the case stage, consider this as an alternative to prying the battery loose. Also if somebody can work out a way to make the button accessible from outside the case it might be a useful modification.
Click to expand...
Click to collapse
Oh I was so keen when I came across this post. A Reset Button! How great would that be?
Tried it, unfortunately it did not resurrect my dead as a doorstop TP. I was so hoping...
I just put a 'new' EBay battery in it a couple of days ago and tried trickle charging with a 1000mA charger for 24hrs. No joy there either.
All I get when I plug it into the PC is that it shows up as a "QDLoader 9008" (QHSUB_DLOAD driver) .
No flicker of life or light whats so ever...
_mr
middle_road said:
Oh I was so keen when I came across this post. A Reset Button! How great would that be?
Tried it, unfortunately it did not resurrect my dead as a doorstop TP. I was so hoping...
I just put a 'new' EBay battery in it a couple of days ago and tried trickle charging with a 1000mA charger for 24hrs. No joy there either.
All I get when I plug it into the PC is that it shows up as a "QDLoader 9008" (QHSUB_DLOAD driver) .
No flicker of life or light whats so ever...
_mr
Click to expand...
Click to collapse
Try to borrow a Touchstone conductive charger if you can. It's the only thing that has worked for me when it has totally drained down.
All the best.
sstar said:
Try to borrow a Touchstone conductive charger if you can. It's the only thing that has worked for me when it has totally drained down.
All the best.
Click to expand...
Click to collapse
That's what I was thinking - no joy there either... It is not even showing signs of getting the least bit warm.
I keep thinking and hoping that there is some way to resurrect this one but I may be wrong...
It's currently trickling on a 1000mA charger. Tomorrow I'm going to try the Touchstone behind it.
If that doesn't start something then I'm going to yank the new battery and along with the old battery charge them like an RC device.
(if I can ascertain the proper way to do that --- )
_mr
After several days on the trickle, still no life.
Took it apart at lunch and with the battery still connected to mobo it is showing 3.1V across the red/black. So I figure the battery
is good. Looks like the mobo is gone.
Not sure what else to try.
_mr
I don't know what happened with my HTC One (M7), but it's completely unresponsive now, and I'm hoping it's not dead.
It was working earlier today (about 3 hours ago), I know that 100% because I turned on/off airplane mode when going into/leaving the dentist this morning.
I drove around today for about 40 minutes or so, I'm fairly certain it was plugged into the car charger (that's what I do with my phone), but I might not have, unfortunately I wasn't paying attention. When I got back home, I went to turn it on and...nothing.
Plugging it into the wall with a known-good charger (works on other phones) gives no charging LED. Plugging it into the computer gives no plug-in noise in windows.
I've tried holding down all combinations of power, volume up, and volume down for 10s, 15s, 30s, 45s, 1m, 2m, 5m intervals. No response whatsoever.
I've also tried with different cables, different outlets, and even went so far as to bend the prong that the USB Micro connector interfaces with, no dice. I've tried USB3.0, USB2.0, and regular power outlets, to no avail. ADB reports no devices found (honestly I don't know what I expected). When someone calls me, it rings 2-3 times before going to voicemail on their end, but the phone sits impassive in my hand.
Is it dead? Is there something I'm missing? I'm really hoping I can salvage it, I love this phone. Unfortunately, I got it from Swappa so I have no warranty or anything, and honestly I really can't be without a phone since I'm waiting on a call back about an interview for a job. Can anyone give me any suggestions/links/things to try? I'm at the point where I'm about to attempt disassembly on my own, but I'd MUCH rather not have to go that route, since I'm more likely to break it than fix it.
Best case scenario! Out of juice. Leave it plugged in to walk for couple days.
Worst case! Look for a new phone
SaHiLzZ said:
Best case scenario! Out of juice. Leave it plugged in to walk for couple days.
Worst case! Look for a new phone
Click to expand...
Click to collapse
Thanks for the response.
I'm going to leave it plugged in overnight, though I believe it is wasted. I contacted HTC Support and they said it was still under warranty, so maybe I can get it replaced through them....Though probably not for free, as I had already rooted it back before they were S-Off, so as soon as it boots it says something like "Experimental bootloader for internal use only, do not distribute outside of HTC" or something like that....without it booting, no way to unroot it
Here's hoping it's completely fried and they don't see that part of it XD
Hello, I've had no luck anywhere else, so I decided to ask here.
My Nook HD Plus has been running CM11 for quite some time with no issues whatsoever. Then, one night, it died, and I can't get it to charge at all. I've tried several outlets, with different cords and everything, with no luck. When plugged in, the indicator light doesn't turn on at all, any color. I tried plugging it into my computers, with the same results. I've also tried holding the power/home/volume buttons and all of that, but still nothing happens. I've also left it plugged in for hours, but it just warms up slightly. Is there anything I can do?
Thanks,
-LBurdick43-
LBurdick43 said:
Hello, I've had no luck anywhere else, so I decided to ask here.
My Nook HD Plus has been running CM11 for quite some time with no issues whatsoever. Then, one night, it died, and I can't get it to charge at all. I've tried several outlets, with different cords and everything, with no luck. When plugged in, the indicator light doesn't turn on at all, any color. I tried plugging it into my computers, with the same results. I've also tried holding the power/home/volume buttons and all of that, but still nothing happens. I've also left it plugged in for hours, but it just warms up slightly. Is there anything I can do?
Thanks,
-LBurdick43-
Click to expand...
Click to collapse
Possibly helpful info is here: http://forum.xda-developers.com/showthread.php?p=53721550
Sent from my BN NookHD+ using Tapatalk
LBurdick43 said:
I've tried several outlets, with different cords and everything, with no luck
Click to expand...
Click to collapse
So several outlets and additional proprietary charging cables but not another usb outlet adapter or is that "everything"?
In any case, the no light thing is probably a good indicator that the tablet is needing a replacement. IF it was getting juice there should be a light.
IF it was plugged in when it happened, could have been an electrical surge. Long term brownouts could potentially cause damage.
I'm also assuming that the port on the tablet isn't simply where the fault it, or perhaps even the battery, or that the light simply doesn't work anymore.
IF its still under warranty could go to B&N for a replacement.
The tablet is dead, it was suddenly. Won't charge or turn on and it's not recognised by the PC. Recovery mode (power button + volume-) doesn't work either.
I know that is not the screen, because the PC doesn't detect the tablet at all. I tried with another battery (my wife has the same tablet), but I had no luck. I also know that the charger and the usb cable are fine.
What else I can do, any ideas or suggestions?
maloyztor said:
The tablet is dead, it was suddenly. Won't charge or turn on and it's not recognised by the PC. Recovery mode (power button + volume-) doesn't work either.
I know that is not the screen, because the PC doesn't detect the tablet at all. I tried with another battery (my wife has the same tablet), but I had no luck. I also know that the charger and the usb cable are fine.
What else I can do, any ideas or suggestions?
Click to expand...
Click to collapse
Are you using the OE usb cable? Have you tried charging using the OE wallwart?
TonyStark said:
Are you using the OE usb cable? Have you tried charging using the OE wallwart?
Click to expand...
Click to collapse
Yes, I'm using the OE usb cables (I have 2) and the OE charger.
maloyztor said:
The tablet is dead, it was suddenly. Won't charge or turn on and it's not recognised by the PC. Recovery mode (power button + volume-) doesn't work either.
I know that is not the screen, because the PC doesn't detect the tablet at all. I tried with another battery (my wife has the same tablet), but I had no luck. I also know that the charger and the usb cable are fine.
What else I can do, any ideas or suggestions?
Click to expand...
Click to collapse
I had the same symptoms after disconnecting and reconnecting battery,I hed to disconnect it for like an hour and then three times try to power on the tablet and it did power on. Maybe your battery is dead so after another hour you may try to use the other battery. If it will work, try to connect the batteries together so the dead one can get a little charge (but do some research I am not sure if it won't have a chance to damage anything) then the same after an hour connect try power on and if it powers on immediately give it a charge.
Mis012 said:
I had the same symptoms after disconnecting and reconnecting battery,I had to disconnect it for like an hour and then three times try to power on the tablet and it did power on. Maybe your battery is dead so after another hour you may try to use the other battery. If it will work, try to connect the batteries together so the dead one can get a little charge (but do some research I am not sure if it won't have a chance to damage anything) then the same after an hour connect try power on and if it powers on immediately give it a charge.
Click to expand...
Click to collapse
Just wondered if you had tried this and if so, how you got on? Asking because I bought my daughter one off ebay and it was working fine when I got it, am sure I recharged it once , she played it and then again in morning and thinks she played it till battery ran out. I have since tried charging via pc and mains power, and have disconnected battery twice (case was v. easy to remove so concerned this fault may be reason it was sold), but cannot get a flicker of a response on screen. i got my daughter this as she was desperate for an android tablet for mods for minecraft as I had bought her a Amazon Fire 7 and from what I could see just after xmas, it wasnt possible to root it or sideload at that time, and she said Amazon had no mods compared to the play store and she had been ecstatic with the mods she had found for her android for the short time she had it. I do know when I plug it into the wall charger that the motherboard area gets warm if its been plugged in for a while? Bit of a noob on this stuff,and off sick with probs with my nervous system so my concentration and memory can be a pia. Anyway I was wondering how I can find out if its goosed or what I can try? One of the batterys advertised on ebay is about £50 which seems steep to me, esp. if it doesnt fix it, and esp since I have been unable to work for a few years cos of this illness. I only bought the tablets cos I had extra money after I finally applied and got pip, and got it backdated. Any recommendations for a reasonably priced option for her for her minecraft? Should I go the tablet\notebook type route or can they not handle minecraft? Bit confused by these new notebooks esp touchscreen ones as new ones seem to have small amounts of ram yet are v. popular.
Thanks for advice\thoughts\feedback and let me know if I should start ,y own thread...I only jumped on this to see how he got on and then as I do nowadays with this illness, I then jumped from topic to topic that jumped into my head x sorry x
nikkiandmidgets said:
Just wondered if you had tried this and if so, how you got on? Asking because I bought my daughter one off ebay and it was working fine when I got it, am sure I recharged it once , she played it and then again in morning and thinks she played it till battery ran out. I have since tried charging via pc and mains power, and have disconnected battery twice (case was v. easy to remove so concerned this fault may be reason it was sold), but cannot get a flicker of a response on screen. i got my daughter this as she was desperate for an android tablet for mods for minecraft as I had bought her a Amazon Fire 7 and from what I could see just after xmas, it wasnt possible to root it or sideload at that time, and she said Amazon had no mods compared to the play store and she had been ecstatic with the mods she had found for her android for the short time she had it. I do know when I plug it into the wall charger that the motherboard area gets warm if its been plugged in for a while? Bit of a noob on this stuff,and off sick with probs with my nervous system so my concentration and memory can be a pia. Anyway I was wondering how I can find out if its goosed or what I can try? One of the batterys advertised on ebay is about £50 which seems steep to me, esp. if it doesnt fix it, and esp since I have been unable to work for a few years cos of this illness. I only bought the tablets cos I had extra money after I finally applied and got pip, and got it backdated. Any recommendations for a reasonably priced option for her for her minecraft? Should I go the tablet\notebook type route or can they not handle minecraft? Bit confused by these new notebooks esp touchscreen ones as new ones seem to have small amounts of ram yet are v. popular.
Thanks for advice\thoughts\feedback and let me know if I should start ,y own thread...I only jumped on this to see how he got on and then as I do nowadays with this illness, I then jumped from topic to topic that jumped into my head x sorry x
Click to expand...
Click to collapse
Firt I would try to trickle charge the battery.
BEFORE YOU DO THIS:
Remove the SD CARD. I forgot to do this and snapped my card straight in half removing the back cover.
This started happening to my ME176 as well but of course not until after I retired it and gave it to my mom.
I would start by letting it sit on the charger for about 30 minutes (since we don't know the current charge state and if the overcharge block is functioning). This will give it a slight charge if dead.
Disconnect charger and remove the back cover and disconnect the battery (as posted earlier). Push and hold the power button a few times even though there is no power.
It may take a few tries of disconnecting and reconnecting the battery before it decides to power up, so keep the cover off while doing this.