(Solved) i9070 jellybean can't start - Galaxy S Advance I9070 Q&A, Help & Troubleshooting

hi all
i have samsung gt-i9070
i was on jellybean stock rom
i tried to install Cm 10.1 but it didn't start i did something wrong but it isn't the problem
i wanted to return to stock jellybean i falshed it by odin but the setup wizard crashed several times and "blahblah.gapps failed to start"
i tried several copies of the stock rom and every time i wiped cashe and reset everything using Cwm
I9070JVBMD1_I9070OJVBMD1_XSG
I9070XXLQG_I9070ITVLQ3_ITV
it all crashed
so i managed to downgrade to Gingerbread but i can't return to jelly bean any more
note:in Cwm : "efs can't be mounted" & "failed to load efs" in red
please help >>>>>>>>.thanks all
note:there was a solution didn;t work for me in forum
it is
install stock jelly-root-wipe system and preload-mount-install stock jelly
finally it is solved from this topic
http://forum.xda-developers.com/showthread.php?t=2353293

try to installing FULL (3 files cont., by Odin) GB
after reboot just flash single-file JB
Sent from SGSA using Tapatalk 4

pawelarc said:
try to installing FULL (3 files cont., by Odin) GB
after reboot just flash single-file JB
Sent from SGSA using Tapatalk 4
Click to expand...
Click to collapse
i did that before and i'm on Ginger now
but ican't return to jelly it crashed all times

up
please help

* Use Odin 3.07 for JB not 1.85,
* Download THIS firmware and extract from zip,
* Make sure you installed drivers (ODIN should say "Added" when you connect your phone in download mode)
* Open ODIN and give the tar file (you extracted) to PDA section,
* Close the device then go into download mode and connect device to PC, (and again ODIN should say "Added")
* Flash
- after flashing phone probably go into bootlop so remove the battery and go to the recovery mode (VolUp-Home-Power) choose WIPE DATA / FACTORY RESET (This one wipe your apps not internal storage)

it can't help
i did that and the wizard crashed again no change

up up please hellllllllp
i will burn this mobile

Install JB, go to recovery ,do a factory reset.

Sh0m1 said:
Install JB, go to recovery ,do a factory reset.
Click to expand...
Click to collapse
i did that more than 10 times no change
i did it by the original recover and custom recover cwm

amr diab said:
i did that more than 10 times no change
i did it by the original recover and custom recover cwm
Click to expand...
Click to collapse
What cwm did you used? Temp one?
Try this: put some JB stock based ROM on your sd, open CWM and do factory reset and wipe everything you see (cache, dalvik, system, preload...). After that install ROM.
Sent from my GT-I9070 using Tapatalk

shut_down said:
What cwm did you used? Temp one?
Try this: put some JB stock based ROM on your sd, open CWM and do factory reset and wipe everything you see (cache, dalvik, system, preload...). After that install ROM.
Sent from my GT-I9070 using Tapatalk
Click to expand...
Click to collapse
yes temp one
i did that and i installed harshjelly
there is no wizard and it opened normally but no apps can start
and there is no call-camera everything not appeared

amr diab said:
yes temp one
i did that and i installed harshjelly
there is no wizard and it opened normally but no apps can start
and there is no call-camera everything not appeared
Click to expand...
Click to collapse
Try to mount prelaod in recovery, and flash it again. If that do not help, download gapps for 4.1.2 and flash it. Maybe it is because of wrong gapps, left from CM.
Sent from my GT-I9070 using Tapatalk

shut_down said:
Try to mount prelaod in recovery, and flash it again. If that do not help, download gapps for 4.1.2 and flash it. Maybe it is because of wrong gapps, left from CM.
Sent from my GT-I9070 using Tapatalk
Click to expand...
Click to collapse
didn't help man
i also format system and preload then mount but no help too
but i think this problem because of efs can't be mounted in recovery ?
and there is an option on odin clear efs i tricked it but not help
thanks for your replies

up

use the search:
http://forum.xda-developers.com/showthread.php?t=2548933
Exactly the same case, with solution.
EDIT: my second link was wrong: it is actually a previous thread about same case.
http://forum.xda-developers.com/showthread.php?t=2546728

alete89 said:
use the search:
http://forum.xda-developers.com/showthread.php?t=2548933
http://forum.xda-developers.com/showthread.php?t=2667579
Exactly the same case, with solution.
Click to expand...
Click to collapse
Thanks God
there is a hope
but i'm sorry i can't understand this
On another device (same model and region) I did:
dd if=/dev/block/mmcblk0p2 of=/sdcard/modemfs.img.md5
Copied generated file to my sdcard and did:
dd if=/sdcard/modemfs.img.md5 of=/dev/block/mmcblk0p2
Reboot and it's done.
how i use this codes and which one i must use
and is it in terminal program ?
my baseband is oK and 3G is oK how i do that solution ?
sorry for bad english

Make all wipes including fix permissions in cwm temporaly in 4.1.2, a counter going to start after fix permissions... so extract the battery, and then flash a stock jb via odin...
Sorry for my bad english

amr diab said:
Thanks God
there is a hope
but i'm sorry i can't understand this
On another device (same model and region) I did:
dd if=/dev/block/mmcblk0p2 of=/sdcard/modemfs.img.md5
Copied generated file to my sdcard and did:
dd if=/sdcard/modemfs.img.md5 of=/dev/block/mmcblk0p2
Reboot and it's done.
how i use this codes and which one i must use
and is it in terminal program ?
my baseband is oK and 3G is oK how i do that solution ?
sorry for bad english
Click to expand...
Click to collapse
If you don't have any baseband or 3g problem the steps should be:
1)downgrade to GB 2.3.6, you can try downgrading with ODIN 1.85 with 3 files (PDA, PIT, CSC) and checking the "re-partition" option (be carefull, this will erase the "sdcard0" internal phone memory!, make a backup if you have personal stuff there). If EVERYTHING works well, (even 3g and baseband) continue to:
2) flash JB 4.1.2 stock with odin (a newer one if you have it) only with PDA (without checking re-partition!) and that should work well.
If you have back ups made with CWM or TWPR: flash your custom recovery from stock recovery and then root.
Good luck!

alete89 said:
If you don't have any baseband or 3g problem the steps should be:
1)downgrade to GB 2.3.6, you can try downgrading with ODIN 1.85 with 3 files (PDA, PIT, CSC) and checking the "re-partition" option (be carefull, this will erase the "sdcard0" internal phone memory!, make a backup if you have personal stuff there). If EVERYTHING works well, (even 3g and baseband) continue to:
2) flash JB 4.1.2 stock with odin (a newer one if you have it) only with PDA (without checking re-partition!) and that should work well.
If you have back ups made with CWM or TWPR: flash your custom recovery from stock recovery and then root.
Good luck!
Click to expand...
Click to collapse
i did these things before a lot of times and i'm now on GB and everything is fine
i ca't start jellybean any more because the wizard crashes and i tried harshjelly but came without any programs like you
but your baseband was xxxx and u solved it with the modem file and everything is ok ? am i right ?
i don't have this problem how can i fix the jellybean problem ?

amr diab said:
i did these things before a lot of times and i'm now on GB and everything is fine
i ca't start jellybean any more because the wizard crashes and i tried harshjelly but came without any programs like you
but your baseband was xxxx and u solved it with the modem file and everything is ok ? am i right ?
i don't have this problem how can i fix the jellybean problem ?
Click to expand...
Click to collapse
Well. When I had that problem I wasn't sure if wizard and baseband problem was related, but both things fixed when I replaced my modemfs with one from my friend.
If you want to try the same (at your own risk), you have to:
1) have a rooted GB (there are guides all over the internet)
2) download the file: goo.gl/DzAjza (it is from company: Claro, Argentina, UBLD1, I'm sure it is not "device specific" but I'm not sure if it is "carrier specific") and put it in your phone.
3) install any Terminal app from playstore
4) in terminal write:
"su" (to get super user privileges)
and then:
dd if=/sdcard/modemfs.img.md5 of=/dev/block/mmcblk0p2
assuming that you put the file in your sdcard. (write carefully!!! you can mess it up hard if you misstype here)
then reboot and check if everything work properly, if yes, try flashing JB with Odin again and cross fingers.
Good luck!

Related

[Q] from rooted version 2.2 to rooted version 4.0 or more?

Hi,
I was redirected to this part of the forum. A friend of mine rooted my samsung mobile Galaxy S I9000 with a android 2.2 version. I cannot contact him anymore to help me with the update and I am really a newbie in this rooting world. So, I am coming on this forum to have some advice. I read information on rooting your device, in which everything is explained very well, but could not find information on how to update once a device was rooted (probably I did not search in the right place). What I did so far is:
1) Taking backup of my pics (by manually drag and drop the folder on my pc), SMS and call logs (with sms backup + app), syncronized my contacts with gmail so that I can recover them later on and backup the music folder. I installed backup Titanium to back up my apps on my SD card.
But now, I am stuck with some questions (could you guide me where to find the information?):
1) Which most recent version of Android is supported on the device I have? Which version will work best?
2) Is there important information that I forgot to back up? + I have a problem with the backup Titanium app. It could reach my root in the beginning, but then the Superuser app updated the binary and from then on my titanium app got stuck when getting access to the root. Any idea how to solve this? Install an older version of the bin.file? How to do that exactly? thanks! => I could fix this problem by installing an older version of superuser in CW recovery. If others have problems with this issue, I can provide help from now on
3) Is there a guide with step by step procedure on which files I have to download on my pc and which procedure to follow? Or could you advice me some useful links?
thanks!
1) there is android 4.2.2 available for this amazing device
2) you propably forgot to backup efs folder
3)
- 1) follow this guide to get android 2.3.6 to your device: http://www.darkyrom.com/index.php?threads/odin-darkyrom-10-2-resurrection-gt-i9000.4272/
- 2) follow this guide to get android 4.2.2 (cm 10.1) to your device after: http://wiki.cyanogenmod.org/w/Install_CM_for_galaxysmtd
- 3) now you can flash most of the roms you find in i9000 android development forum. i personally use slimrom
copy /efs! backup ur imei n md5 in efs first! copy da whole efs file! or do nandroid backup.
READ N FOLLOW CAREFULLY here
http://forum.xda-developers.com/showthread.php?t=2149455
considering u already done flashing Sammy n CF
prepare for ROM & kernel(optional) hunt! go to dev section and choose which JB u wanted.download it together with cm9.1.0 n copy to root of internal sd.
n make sure to flash cm9.1.0 stable from cyanogenmod website (galaxymtd) first from 2.3.6, first flash will bootloop, go back to recovery with 3 combo button. flash again n dont leave recovery.
after done flashing twice (if flash ended too quick, then flash again). direct flash 4.1/4.2 chosen rom, twice (first flash will come up with error, juz ignore it flash again (bootloop) recovery again n flash again
Sent from my GT-I9000 using xda premium
A bit off topic, but i didnt want to start a new thread for that...
My question is: is there an android 4.0 version with full touchwiz?
I mean the whole tweaks as slide the contact to message/call and so on
I only foubd CM 9 based ROMs which are themed to look like touchwiz and had the launcher...but i miss the sms app interface, smilies, slide to call things
Is there a port from the SGS2?
Greets Vauvenal7
Sent from my SGS i9000
Vauvenal7 said:
A bit off topic, but i didnt want to start a new thread for that...
My question is: is there an android 4.0 version with full touchwiz?
I mean the whole tweaks as slide the contact to message/call and so on
I only foubd CM 9 based ROMs which are themed to look like touchwiz and had the launcher...but i miss the sms app interface, smilies, slide to call things
Is there a port from the SGS2?
Greets Vauvenal7
Sent from my SGS i9000
Click to expand...
Click to collapse
maybe nope, but try mod urself by searching on theme n app section
Sent from my GT-I9000 using xda premium
Thanks guys!! Will have a look at your suggestions! I guess both explanations are more or less equivalent !! Right?
mogwai123 said:
Thanks guys!! Will have a look at your suggestions! I guess both explanations are more or less equivalent !! Right?
Click to expand...
Click to collapse
yap, its da same, but do some reading first
Sent from my GT-I9000 using xda premium
when I copy my efs folder, I see that it is empty. any idea? I should not proceed further? What should I do?
UPDATE: phone still finds my IMEI number when dialing *#06#
if ur imei intact, then leave it, i dont know which ROM ur using but try to see /efs with option show hidden in rooted file explorer
Sent from my GT-I9000 using xda premium
I followed the guide you mentioned here:
http://forum.xda-developers.com/show....php?t=2149455
in which they install that JVU ROM... then they say at the end that you have to unmount SD card (but that option was gray in my case) and wipe the USB storage and then reboot in recovery and do those 4 wipes, what I did, and then he mentioned that you could install your custom ROM, so I put the version of slimrom 4.2.2 on my sd card and launched it for installation.
However, the procedure started, but after a few seconds already my phone rebooted and now it is stuck at the logo of Semaphore...
What did I wrong? And what should I do?
mogwai123 said:
I followed the guide you mentioned here:
http://forum.xda-developers.com/show....php?t=2149455
in which they install that JVU ROM... then they say at the end that you have to unmount SD card (but that option was gray in my case) and wipe the USB storage and then reboot in recovery and do those 4 wipes, what I did, and then he mentioned that you could install your custom ROM, so I put the version of slimrom 4.2.2 on my sd card and launched it for installation.
However, the procedure started, but after a few seconds already my phone rebooted and now it is stuck at the logo of Semaphore...
What did I wrong? And what should I do?
Click to expand...
Click to collapse
Should I shut down my phone and try to put it in download mode again to put the JVU rom on it again via odin? is that the best strategy? Or should I do something else? and if that would work, what is then the best procedure to avoid such situations again?
nope, u did rite, but also wrong, ok, read carefully here....
flashing for upgrade is easy if u follow carefully, when in GB, after flashing CF ROOT, flashing to 4.0 (cm9) first (take da zip from cyanogenmod website) but luckily ur on 2.3.6 JVU (if u follow da link i gave), so it will be safe (safe procedure will be GB-ICS-JB), first flash will bootloop, second flash (sometimes) will occur error n third flash will succeed, which means u hav to flash twice or thrice or maybe 4 times! if its bootloop, go to recovery back by 3 button combo (its da matter of when u release da combo button, release it rite after u see da first white bootsplash)
bootloop cause by changing da partition tp ext4, its common
but if u already try to reach recovery n failed most times, u need to flash back firmware n cf root.
Sent from my GT-I9000 using xda premium
compacity said:
nope, u did rite, but also wrong, ok, read carefully here....
flashing for upgrade is easy if u follow carefully, when in GB, after flashing CF ROOT, flashing to 4.0 (cm9) first (take da zip from cyanogenmod website) but luckily ur on 2.3.6 JVU (if u follow da link i gave), so it will be safe (safe procedure will be GB-ICS-JB), first flash will bootloop, second flash (sometimes) will occur error n third flash will succeed, which means u hav to flash twice or thrice or maybe 4 times! if its bootloop, go to recovery back by 3 button combo (its da matter of when u release da combo button, release it rite after u see da first white bootsplash)
bootloop cause by changing da partition tp ext4, its common
but if u already try to reach recovery n failed most times, u need to flash back firmware n cf root.
Sent from my GT-I9000 using xda premium
Click to expand...
Click to collapse
Ok, thanks!!!! this worked!!! I justed flashed cm9 and it works. So, if I understand well now, I can just return in recovery mode and install from zip from sd card to cm10 and then for instance to slimrom? Or between 'two' flashes, I need to follow the last part of the procedure in the link you gave me? So:
"Now, what I do now is go into :
Settings > SD Card and Storage > Unmount SD and Wipe that and then at the bottom Wipe Format USB Storage
Enable USB Debugging > Plug in Phone
Window should open up showing your phone Directory..
Copy over your ROM that you want
Shut Down Phone
Reboot into Recovery (Vol UP - Menu - Power)
Wipe the 4 things (probably know these... you should do)
Data / Factory Reset
Cache Partition
Go to Advanced > OK
Dalvik Cache
Battery Stats
Go Back > OK
To move Up or Down > Use the Left Side Volume Rocker Switches with Menu to OK Action
Install your Custom ROM from Zip Card that you want..."
OR: can I just go to recovery mode and do install from zip without doing that procedure with "wipe" etc?
Just to know, as I am just a newbie in these things!!! But I want to thank you once again for the clear explanations and the good help!!!!
juz flash mate , its easy, da important thing is to follow da sequence, thats all, juz flash, wiping cache or resetting juz for changing ROM. not upgrading
juz FLASH it
GB-ICS (twice)(do not leave recovery after second flash)-(any custom JB ROM u choose(twice or thrice))(make sure u already put da zip file in internalsd). dont need any wiping.
but FLASH AT UR OWN RISK,remember that.
n yes, recovery need hardbutton except TWRP recovery.
Sent from my GT-I9000 using xda premium
---------- Post added at 10:57 AM ---------- Previous post was at 10:34 AM ----------
here info
updating ROM from firmware (juz flash)
changing from custom ROM to any custom ROM (wipe ALL cache, factory reset, wipe dalvik n mount system n format system)
changing/flashing inbetween custom kernel (wipe cache n wipe dalvik cache)
fone slowing down (reboot or fix permission)
changing/flashing/applying tweak (wipe dalvik cache)
Sent from my GT-I9000 using xda premium
compacity said:
juz flash mate , its easy, da important thing is to follow da sequence, thats all, juz flash, wiping cache or resetting juz for changing ROM. not upgrading
juz FLASH it
GB-ICS (twice)(do not leave recovery after second flash)-(any custom JB ROM u choose(twice or thrice))(make sure u already put da zip file in internalsd). dont need any wiping.
but FLASH AT UR OWN RISK,remember that.
n yes, recovery need hardbutton except TWRP recovery.
Sent from my GT-I9000 using xda premium
---------- Post added at 10:57 AM ---------- Previous post was at 10:34 AM ----------
here info
updating ROM from firmware (juz flash)
changing from custom ROM to any custom ROM (wipe ALL cache, factory reset, wipe dalvik n mount system n format system)
changing/flashing inbetween custom kernel (wipe cache n wipe dalvik cache)
fone slowing down (reboot or fix permission)
changing/flashing/applying tweak (wipe dalvik cache)
Sent from my GT-I9000 using xda premium
Click to expand...
Click to collapse
Thanks!!!! Just one small question. I just flashed CM10 in recovery mode and first flash gave error, second went well. Then while still being in recovery mode I directly flashed slimrom and that went well from the first time. Do you always flash a second time to make sure that things went well or this is ok then?
mogwai123 said:
Thanks!!!! Just one small question. I just flashed CM10 in recovery mode and first flash gave error, second went well. Then while still being in recovery mode I directly flashed slimrom and that went well from the first time. Do you always flash a second time to make sure that things went well or this is ok then?
Click to expand...
Click to collapse
as i already said, flash more than 2 times when upgrading, juz upgrading process. GB-ICS-JB (CM7-CM9-CM10/10.1) is upgrading process.
changing ROM not necessarily need double flashing, but u can do it if ur not satisfy whether da ROM already flashed or not
Sent from my GT-I9000 using xda premium
ok, thanks!!! no, everything is working fine with this slimrom, except for google play that does not seem to open once I install it. It opens and closes directly... but I guess there are persons that had the same problem. will have to check the forum for a solution
mogwai123 said:
ok, thanks!!! no, everything is working fine with this slimrom, except for google play that does not seem to open once I install it. It opens and closes directly... but I guess there are persons that had the same problem. will have to check the forum for a solution
Click to expand...
Click to collapse
Hmmm, is probably because I get this error when starting slimrom: invalid IMEI number...I flashed it a second time, but it gave me the same error...
Which gapps have you flashed? Slimbean needs a special package, you find it under slimroms.net.
Sent from my GT-I9000 using xda app-developers app
wget21 said:
Which gapps have you flashed? Slimbean needs a special package, you find it under slimroms.net.
Sent from my GT-I9000 using xda app-developers app
Click to expand...
Click to collapse
I will have a look there for that google play problem.
More problematic is that problem of IMEI. When I flashed from CM 9 to CM10 I did not do that wipe of cache and data as suggested above (the reply came later on), and then I flashed slimrom. That I forgot to wipe between CM9 and CM10, can that be the cause of wrong IMEI now? Is the solution now, to wipe cache and data, to flash again CM 10 and to flash then slimrom again?
Or should I just leave everything like that and do a recovery of my efs folder? If yes, any link for this?

RemICS

Hello guys,
i have succesfully flashed the new RemICS rom. It's works fine. When i will install the new addonpack, it's still show the bootanimation. I wait for 30 min but nothing happened. I try it 3 times but nothings change. I come from ICS 4.3. Can anyone please help me out?
And yes... I follow the installation steps.
Rom link: http://forum.xda-developers.com/showthread.php?t=2427514
Thanks,
Marvin
PS: Sorry for my bad english.
Did you try to do a full wipe?
Sent from my GT-I9001 using xda app-developers app
KiLLAH89 said:
ICS 4.3
Click to expand...
Click to collapse
4.3 is Jelly Bean (JB), not ICS (..."I scream sand witch"....) could it be that you 've flashed wrong Gapps version?
käsebr0t:45552591 said:
Did you try to do a full wipe?
Click to expand...
Click to collapse
Yes everytime i flashed it.
tetakpatak said:
4.3 is Jelly Bean (JB), not ICS (..."I scream sand witch"....) could it be that you 've flashed wrong Gapps version?
Click to expand...
Click to collapse
No, thats not possible, see http://forum.xda-developers.com/showthread.php?t=2427514. I flashed all this yesterday on it's release. Its run now, i install no performance tweaks from the AIO.
KiLLAH89 said:
Yes everytime i flashed it.
No, thats not possible, see http://forum.xda-developers.com/showthread.php?t=2427514. I flashed all this yesterday on it's release. Its run now, i install no performance tweaks from the AIO.
Click to expand...
Click to collapse
It is just name of the ROM, and the developer writes you clearly in the first blue field, in the first text line:
Android Base CM10.1.3. RC1 JellyBean
JellyBean is not ICS (ICS is 4.0.x) so you need Gapps for CM10.1x / Android 4.2.x
CyanogenMod 9 is based on ICS
HELP needed for RemICS Odin installation
Not sure whether to start a new thread or not so for the sake of making xda a little less cluttered i will first post my query here:
It refers to the RemICS ROM thread already mentioned
http://forum.xda-developers.com/showthread.php?t=2300693
This looks like a great ROM and i would like to do a one time flash using Odin
Are there any install methods using Odin. I see there is a full download on the page but it appears to be for a I9003. Have searched all over and not seen anything as yet
FYI: I am currently running DarkysROM JVQv10.2 Extreme Edition, firmware 2.3.4
Kernel Version 2.6.35.7-I9000XXJVQ-CL281085
thx in advance :good:
[email protected] said:
Not sure whether to start a new thread or not so for the sake of making xda a little less cluttered i will first post my query here:
It refers to the RemICS ROM thread already mentioned
http://forum.xda-developers.com/showthread.php?t=2300693
This looks like a great ROM and i would like to do a one time flash using Odin
Are there any install methods using Odin. I see there is a full download on the page but it appears to be for a I9003. Have searched all over and not seen anything as yet
FYI: I am currently running DarkysROM JVQv10.2 Extreme Edition, firmware 2.3.4
Kernel Version 2.6.35.7-I9000XXJVQ-CL281085
thx in advance :good:
Click to expand...
Click to collapse
This isn't meant to be flashed via Odin.
Download the rom + addons + gapps + CM9 (you don't need CM9 gapps). You can download the rom + addons from here: http://forum.xda-developers.com/showthread.php?t=2075058
1.) Backup everything you need to- call logs, SMS, bookmarks, etc with Titanium or other methods of your choice
2.) Reboot into recovery. Perform the three wipe combo (data, cache, Dalvik)
3.) Flash CM9. You'll probably have to flash it twice- once for the kernel, another time for the rom. Let it boot.
4.) Once CM9 has booted, check that you still have reception.
5.) Reboot into recovery again and do the wipe combo. This time choose to flash the base rom. You'll need to flash it three times- once due to the incompatible partition (first flash overcomes this), another time for the kernel, a third time for the rom.
6.) Once the base rom's finished flashing, reboot. Check you still have your IMEI- you'll know if you still have reception.
7.) Reboot to recovery, flash addons (flash Addons then Addons_V1)
8.) Reboot
9.) Back to recovery (AGAIN), flash gapps.
Unfortunately a one-time flash with Odin isn't possible. But the endless flashes you have to do for RemICS V6 is well worth it
Sent from my GT-P7510 using Tapatalk HD
thx for reply
thx for your reply and apologies for getting back to you late.
If only i could do it the way you suggested but for some reason (me) i have messed the phone so that it now no longer is able to mount the external SDCard so putting the relevent zip files on the ext card is useless because in recovery mode using CWM these files fail to show.
I note that via CWM it shows the card as unmounted. If i try and do a mount it fails.
any ideas?
thx
Lawrence
Soryuu said:
This isn't meant to be flashed via Odin.
Download the rom + addons + gapps + CM9 (you don't need CM9 gapps). You can download the rom + addons from here: http://forum.xda-developers.com/showthread.php?t=2075058
1.) Backup everything you need to- call logs, SMS, bookmarks, etc with Titanium or other methods of your choice
2.) Reboot into recovery. Perform the three wipe combo (data, cache, Dalvik)
3.) Flash CM9. You'll probably have to flash it twice- once for the kernel, another time for the rom. Let it boot.
4.) Once CM9 has booted, check that you still have reception.
5.) Reboot into recovery again and do the wipe combo. This time choose to flash the base rom. You'll need to flash it three times- once due to the incompatible partition (first flash overcomes this), another time for the kernel, a third time for the rom.
6.) Once the base rom's finished flashing, reboot. Check you still have your IMEI- you'll know if you still have reception.
7.) Reboot to recovery, flash addons (flash Addons then Addons_V1)
8.) Reboot
9.) Back to recovery (AGAIN), flash gapps.
Unfortunately a one-time flash with Odin isn't possible. But the endless flashes you have to do for RemICS V6 is well worth it
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse
[email protected] said:
thx for your reply and apologies for getting back to you late.
If only i could do it the way you suggested but for some reason (me) i have messed the phone so that it now no longer is able to mount the external SDCard so putting the relevent zip files on the ext card is useless because in recovery mode using CWM these files fail to show.
I note that via CWM it shows the card as unmounted. If i try and do a mount it fails.
any ideas?
thx
Lawrence
Click to expand...
Click to collapse
What about your internal storage?
Sent from my GT-P7510 using Tapatalk HD
Here is where my noob-ness kicks in.
What internal storage is available by default on the Note1? Is it just the internal sdcard?
what puzzled me when I last flashed with odin (repeated it a number of times as I was trying to get the device to recognise ext sd card) to get the current Darky Extreme rom on (which is working fine no problem at all) is that there was still some relic directory structure left over. These were all empty folders visible when navigating within CWM. Didn't matter what type of formatting I did they wouldn't go. To summarise: much confusion and something got twisted.
So questions arising are:
-How to nuke the internal disk/card properly so there are no remnants prior to me doing another darky reinstall?
-Then, how to copy a zip file to internal card but still have it remain after the format and wipes that would precede a zip install?
-How to fix the device to mount the ext sdcard? FYI other sdcards can't be mounted either. I have tried 4 different ones. And here's the kicker-once booted I go to file manager and there I can see and access all the files/folders on the external card!!! So it's definitely a phone problem as opposed to a sdcard problem. Something got flagged along the line.
Rgrds
Lawrence
Soryuu said:
What about your internal storage?
Sent from my GT-P7510 using Tapatalk HD
Click to expand...
Click to collapse

[Q] i9070 Galaxy Advance HELP !!!

I have recently installed Carbon ROM Build 11 on my Galaxy S Advance. But now I'm not getting used to this Kitkat interface and I want to go back into my stock Jellybean. My phone is currently running on Cyanogen Mod.
Is it possible to downgrade from 4.4.2 to the default jellybean ? If so, then please explain it to me.
I want to go back as fast as I can . I'm asking this doubt here because I don't want to something wrong and end up bricking my device.
I'm new to these forums, so I'm sorry if I have done something wrong. Please help me get out of this problem . Any help will be greatly appreciated
Flash your stock firmware with Odin. Fastest way...
Trimis de pe al meu GT-I9195
R_a_z_v_a_n said:
Flash your stock firmware with Odin. Fastest way...
Trimis de pe al meu GT-I9195
Click to expand...
Click to collapse
Can you please PM me the exact steps to do it with download link ? I just want do it correctly without bricking.
Answer these questions , if possible :-
1) Will all my data be erased ?
2) Does it unroot my phone ?
3) Will it brick my phone ?
Thanks for answering
Download from samsung-updates.com stock JB firmware, unzip on your PC, open Odin, put the phone in DL and proceed.
That .tar file put it on PDA, wait few moments until check that FW, and hit Start.
Do not unplug the phone until Odin said "Passed" and your phone is rebooted.
Check this guide for more info's, maybe i forget something :
http://forum.xda-developers.com/showthread.php?t=2198341
Trimis de pe al meu GT-I9195
R_a_z_v_a_n said:
Download from samsung-updates.com stock JB firmware, unzip on your PC, open Odin, put the phone in DL and proceed.
That .tar file put it on PDA, wait few moments until check that FW, and hit Start.
Do not unplug the phone until Odin said "Passed" and your phone is rebooted.
Check this guide for more info's, maybe i forget something :
http://forum.xda-developers.com/showthread.php?t=2198341
Trimis de pe al meu GT-I9195
Click to expand...
Click to collapse
Thnx .. but can I perform these steps to downgrade from kitkat 4.4.2 to jellybean ?
Because in that thread, it is written from GB to JB.
I'm currently running Carbon rom Kitkat. So can I follow these steps to get back to jellybean ?
Fireblaze15 said:
Thnx .. but can I perform these steps to downgrade from kitkat 4.4.2 to jellybean ?
Because in that thread, it is written from GB to JB.
I'm currently running Carbon rom Kitkat. So can I follow these steps to get back to jellybean ?
Click to expand...
Click to collapse
Yes, follow what i tell you and that guide and no problems.
Trimis de pe al meu GT-I9195
Okiee.. Thnx. I got my firmware for i9070 from samsung-updates.com.
One last doubt... I recently reinstalled my Windows in my computer. I have installed KIES. But how do I know if I have the drivers for i9070 ?
KIES does not recognize my phone since it is rooted.
How will I know if the drivers are installed ?
Fireblaze15 said:
Okiee.. Thnx. I got my firmware for i9070 from samsung-updates.com.
One last doubt... I recently reinstalled my Windows in my computer. I have installed KIES. But how do I know if I have the drivers for i9070 ?
KIES does not recognize my phone since it is rooted.
How will I know if the drivers are installed ?
Click to expand...
Click to collapse
You don't need Kies. Only Samsung drivers and Odin.
Samsung drivers you can take from here: http://www.samsung.com/hk_en/support/model/GT-I9070HKATGY-downloads
R_a_z_v_a_n said:
You don't need Kies. Only Samsung drivers and Odin.
Click to expand...
Click to collapse
Okay...so I have all the files now
Final question.... After flashing with ODIN, when I reboot the device, will it reboot normally ? Or will it go into a boot loop ?
Will any of my data be erased in this process ?
Fireblaze15 said:
Okay...so I have all the files now
Final question.... After flashing with ODIN, when I reboot the device, will it reboot normally ? Or will it go into a boot loop ?
Will any of my data be erased in this process ?
Click to expand...
Click to collapse
If you get a bootloop you must do factory reset. All things from internal memory and sd card will be there, only you will lose apps, contacts, sms and stuff what is wiped when you do factory reset.
shut_down said:
If you get a bootloop you must do factory reset. All things from internal memory and sd card will be there, only you will lose apps, contacts, sms and stuff what is wiped when you do factory reset.
Click to expand...
Click to collapse
Okay, thnx ...I will backup before flashing
shut_down said:
If you get a bootloop you must do factory reset. All things from internal memory and sd card will be there, only you will lose apps, contacts, sms and stuff what is wiped when you do factory reset.
Click to expand...
Click to collapse
I want to install LightJB v1.2 for my phone i9070.
So to do that , what am I exactly supposed to do ? Should I go to stock JB and then flash LightJB, or straight away from Kitkat , can I install LightJB using ODIN ?
Fireblaze15 said:
I want to install LightJB v1.2 for my phone i9070.
So to do that , what am I exactly supposed to do ? Should I go to stock JB and then flash LightJB, or straight away from Kitkat , can I install LightJB using ODIN ?
Click to expand...
Click to collapse
Option 1: Go back to stock, root it, install CoCore, install LightJB.
Option 2: Use this script to format preload partition (the one with zip that you flash in recovery) http://forum.xda-developers.com/showthread.php?t=2612540 then install LightJB (with all wipes).
shut_down said:
Option 1: Go back to stock, root it, install CoCore, install LightJB.
Option 2: Use this script to format preload partition (the one with zip that you flash in recovery) http://forum.xda-developers.com/showthread.php?t=2612540 then install LightJB (with all wipes).
Click to expand...
Click to collapse
Woah !! My head is spinning now ....hehe
If I go on to do something else other than stock, then I'm sure to brick this device.
Anyway thanks for all the help you guys gave me, if I have doubts or trouble in flashing, I'll ask you guys again
I'm OK with the stock firmware. I'll just connect my device with ODIN , put the .tar.md5 file into PDA , go into download mode and click START.
Before everything , I'll back up my contacts, sms , etc.
Did I say the steps correctly ?
Fireblaze15 said:
Woah !! My head is spinning now ....hehe
If I go on to do something else other than stock, then I'm sure to brick this device.
Anyway thanks for all the help you guys gave me, if I have doubts or trouble in flashing, I'll ask you guys again
I'm OK with the stock firmware. I'll just connect my device with ODIN , put the .tar.md5 file into PDA , go into download mode and click START.
Before everything , I'll back up my contacts, sms , etc.
Did I say the steps correctly ?
Click to expand...
Click to collapse
Yes, that is correct.
Sent from my GT-I9070 using Tapatalk
Shall I wipe cache and do a factory reset before flashing or after flashing ? Is it compulsory to do it ?
Fireblaze15 said:
Shall I wipe cache and do a factory reset before flashing or after flashing ? Is it compulsory to do it ?
Click to expand...
Click to collapse
Whenever you want. Just do it before you boot after flashing it.
So ODIN doesn't make the device auto reboot ?
What if ODIN makes it reboot automatically and then hangs on the boot screen ?
Fireblaze15 said:
So ODIN doesn't make the device auto reboot ?
What if ODIN makes it reboot automatically and then hangs on the boot screen ?
Click to expand...
Click to collapse
It does make auto reboot. Problem with data or cache from old ROM makes hangs on the boot screen. So you must do factory reset if it occurs.
And you always can go to recovery again and do factory reset.
P.S. To make it more clear to you: Odin flash firmware, recovery flash ROM. ROM is modification, firmware contains more things than ROM.
Thank you to all you guys especially shut_down and R_A_Z_V_A_N for helping me out
Its done and I'm back to stock JB Thnx again.
[ This thread can be marked as solved ]​

[Q] need urgent help! bricked it

hey eveyone!
my device is galaxy s advance gt-i9070 on which i was using cutom rom aicp 3.5 nightly (4.4.2 kitkat) with minor bugs and cwm recovery 6.0.4.7
i decided to switch to paranoid android 3.69 for smoother perfomance but sadly i bricked my device. although i had backed up my rom using cwm recovery on sd card. but the most sad part is that even recovery is not working. it just reboots again and again. someone told me to flash stock firmware via odin as the download mode is working. but i am worried that my data will be lost. can anyone tell me my data will be lost or not????
and if it ll lost than any way to save it or recover it/ ? i had extremely precious data in it. but being careless i didnt backed my personal data in my laptop.. please help me guys.. ready to pay any cost for my data
shivamgaba22 said:
hey eveyone!
my device is galaxy s advance gt-i9070 on which i was using cutom rom aicp 3.5 nightly (4.4.2 kitkat) with minor bugs and cwm recovery 6.0.4.7
i decided to switch to paranoid android 3.69 for smoother perfomance but sadly i bricked my device. although i had backed up my rom using cwm recovery on sd card. but the most sad part is that even recovery is not working. it just reboots again and again. someone told me to flash stock firmware via odin as the download mode is working. but i am worried that my data will be lost. can anyone tell me my data will be lost or not????
and if it ll lost than any way to save it or recover it/ ? i had extremely precious data in it. but being careless i didnt backed my personal data in my laptop.. please help me guys.. ready to pay any cost for my data
Click to expand...
Click to collapse
Flashing stock firmware with Odin will not delete your data from SD card. You will probably need to do factory reset, it will delete your contacts, sms, apps... But stuff from internal and external sd will remain there.
You bricked it because 4.4.2 uses preload partition for a swap, and it is partitioned in different way. And on PA 3.69 is probably different.
Or ROM zip of PA was corrupted.
thankyou and one more question
shut_down said:
Flashing stock firmware with Odin will not delete your data from SD card. You will probably need to do factory reset, it will delete your contacts, sms, apps... But stuff from internal and external sd will remain there.
You bricked it because 4.4.2 uses preload partition for a swap, and it is partitioned in different way. And on PA 3.69 is probably different.
Or ROM zip of PA was corrupted.
Click to expand...
Click to collapse
thanx a lot buddy now i can flash it being tension free. but can you tell me the way to flash PA without bricking /????
shivamgaba22 said:
thanx a lot buddy now i can flash it being tension free. but can you tell me the way to flash PA without bricking /????
Click to expand...
Click to collapse
I did not use that version that you used. I think that you will not have a problem when you install it over stock, I explained you why you had problem when you did it over CM11.
Sent from my GT-I9070 using Tapatalk
Thanx a lot
Everything fine now with all data restored..
Once again thnx buddy
Sent from my GT-I9070 using XDA Premium 4 mobile app
Hi
I 've bricked my phone as i was trying to clear cache 'n partition of my rooted phone. I assume it must have cleared the software as well.
i'm trying to flash it via odin but it is showin FAIL. i'm putting a pda .md5 file from sammobile 'n it's still not working. pl help.
Neo2803 said:
Hi
I 've bricked my phone as i was trying to clear cache 'n partition of my rooted phone. I assume it must have cleared the software as well.
i'm trying to flash it via odin but it is showin FAIL. i'm putting a pda .md5 file from sammobile 'n it's still not working. pl help.
Click to expand...
Click to collapse
You can't brick phone with clearing cache. Did you wipe system partition? Try to install same ROM that you had (if you had).
Give us a screenshot of Odin fail. What exactly happen. And what is the full name of md5 that you put in pda of Odin. Try different version of Odin too.
shut_down said:
You can't brick phone with clearing cache. Did you wipe system partition? Try to install same ROM that you had (if you had).
Give us a screenshot of Odin fail. What exactly happen. And what is the full name of md5 that you put in pda of Odin. Try different version of Odin too.
Click to expand...
Click to collapse
Yes, i did wipe system partition. Should i have not done that ???????/
Name of md5 - I9070DDULP8_I9070ODDULP8_HOME.tar.md5 .. Can you suggest another one ?
I did have a ROM named light JB which i found here only. Its location showthread.php?t=2244441.
pl guide future course of action.
TIA.
Neo2803 said:
Yes, i did wipe system partition. Should i have not done that ???????/
Name of md5 - I9070DDULP8_I9070ODDULP8_HOME.tar.md5 .. Can you suggest another one ?
I did have a ROM named light JB which i found here only. Its location showthread.php?t=2244441.
pl guide future course of action.
TIA.
Click to expand...
Click to collapse
Go back to recovery, and if you have ROMs zip install it again.
Ofcourse you shouldn't wipe system partition, system files are there...
And if you can't install ROM again, what error do you get in Odin?
shut_down said:
Go back to recovery, and if you have ROMs zip install it again.
Ofcourse you shouldn't wipe system partition, system files are there...
And if you can't install ROM again, what error do you get in Odin?
Click to expand...
Click to collapse
I didn't think twice before wiping it. My bad.
Anyways, That's the issue. I can't go to recovery. Phone only shows the odin mode (if i press VOL. DOWN+HOME+POWER).
Odin simply says FAILS.
Neo2803 said:
I didn't think twice before wiping it. My bad.
Anyways, That's the issue. I can't go to recovery. Phone only shows the odin mode (if i press VOL. DOWN+HOME+POWER).
Odin simply says FAILS.
Click to expand...
Click to collapse
Well then you did not just wipe system, you installed some GB based ROM over?
You have log window in Odin, where it fails? Try to redownlaod firmware again, and then install again.
What version of Odin do you use? Try 3.x.
shut_down said:
Well then you did not just wipe system, you installed some GB based ROM over?
You have log window in Odin, where it fails? Try to redownlaod firmware again, and then install again.
What version of Odin do you use? Try 3.x.
Click to expand...
Click to collapse
Odin Version - 3.07
I'm not sure it s GB based ROM and neither if it's JB. Can you take some more pain 'n send me a proper link ? please.
My older custom ROM is http://forum.xda-developers.com/showthread.php?t=2244441 - http://d-h.st/vge
Neo2803 said:
Odin Version - 3.07
I'm not sure it s GB based ROM and neither if it's JB. Can you take some more pain 'n send me a proper link ? please.
Click to expand...
Click to collapse
But it should be the same:
http://terafile.co/222154239129/INU-I9070DDULP8-20130412134604.zip
http://rapidgator.net/file/0a25225062db04ba2c8216cca12972d2
Check the file zize of zip when you download it, it should be 425MB.
shut_down said:
But it should be the same:
http://terafile.co/222154239129/INU-I9070DDULP8-20130412134604.zip
http://rapidgator.net/file/0a25225062db04ba2c8216cca12972d2
Check the file zize of zip when you download it, it should be 425MB.
Click to expand...
Click to collapse
Lemme download this firmware. but what about the custom ROM I installed last time. Shouldn't THAT be the one i install NOW ???
pasting the link here for your review -
http://forum.xda-developers.com/showthread.php?t=2244441
http://d-h.st/vge
Neo2803 said:
Lemme download this firmware. but what about the custom ROM I installed last time. Shouldn't THAT be the one i install NOW ???
pasting the link here for your review -
http://forum.xda-developers.com/showthread.php?t=2244441
http://d-h.st/vge
Click to expand...
Click to collapse
ROM is fine. And you was on GB or JB before? If you was on GB then this problem you got is normal. You must be on JB (flash JB firmware) if you install JB ROM.
And again, if you get FAIL on Odin DO A SCREENSHOT AND POST IT HERE. To see what cause that fail. Left part of this screenshot is a log http://4.bp.blogspot.com/-gkWcapOu2...gingerbread+s5570jpq8+samsung+galaxy+Mini.jpg
Blue, where it says Message.
This is for other phone, do not pay attention on that, I just told you what I need to see.
---------- Post added at 11:28 AM ---------- Previous post was at 11:02 AM ----------
Neo2803 said:
Lemme download this firmware. but what about the custom ROM I installed last time. Shouldn't THAT be the one i install NOW ???
pasting the link here for your review -
http://forum.xda-developers.com/showthread.php?t=2244441
http://d-h.st/vge
Click to expand...
Click to collapse
And no, you must install Firmware not, not ROM. Because you probably installed JB ROM over GB. That is why you do not have working recovery.
Finally unbricked !!!
shut_down said:
ROM is fine. And you was on GB or JB before? If you was on GB then this problem you got is normal. You must be on JB (flash JB firmware) if you install JB ROM.
[/COLOR]
And no, you must install Firmware not, not ROM. Because you probably installed JB ROM over GB. That is why you do not have working recovery.
Click to expand...
Click to collapse
Finallyyyyyyy !!! yipppieee !!! I'm able to flash my phone with a JB Firmware. I shall be more careful in future.
http://i.imgur.com/UMv2kgs.png
http://i.imgur.com/WPP6yqs.png?1
Thanks a tonnnnn shut_down :good:: God bless you.

Messed up partition table (need a PIT file)

I'm pretty sure i've messed up my partition table. Can anyone help me find a PIT file for my phone, so i can get i repartitioned?
BelugaHval said:
I'm pretty sure i've messed up my partition table. Can anyone help me find a PIT file for my phone, so i can get i repartitioned?
Click to expand...
Click to collapse
What happened and what makes you think it's a PIT problem? Repartitioning a phone should always be the last option.
ArkThompson said:
What happened and what makes you think it's a PIT problem? Repartitioning a phone should always be the last option.
Click to expand...
Click to collapse
No matter what ROM i try i have problem with mounting and unmounting /system ... the only thing i can get working is stock 4.4.4 rom via ODIN.
BelugaHval said:
No matter what ROM i try i have problem with mounting and unmounting /system ... the only thing i can get working is stock 4.4.4 rom via ODIN.
Click to expand...
Click to collapse
Have you tried using a different recovery?
ArkThompson said:
Have you tried using a different recovery?
Click to expand...
Click to collapse
I've tried Philz, CWM and TWRP(which i normally use) the same problem with all recoveries.
what recovery are you using?
try flashing with odin 3.09 twrp 2.8.5.0 official .tar file.
then try any custom rom.
if your partition table would be messed up i belive your phone would be bricked.
hexisg said:
what recovery are you using?
try flashing with odin 3.09 twrp 2.8.5.0 official .tar file.
then try any custom rom.
if your partition table would be messed up i belive your phone would be bricked.
Click to expand...
Click to collapse
II alredy tried that 100 times ... doesnt work
BelugaHval said:
II alredy tried that 100 times ... doesnt work
Click to expand...
Click to collapse
I suspect /system has become R/O (Read Only) So i cant install anything.
BelugaHval said:
I'm pretty sure i've messed up my partition table. Can anyone help me find a PIT file for my phone, so i can get i repartitioned?
Click to expand...
Click to collapse
You may take a look here (without any warranties):
http://forum.xda-developers.com/gal...fo-i9305-pit-file-flash-analysis-pit-t1950591
From my perspective: If you are still able to flash a working stock rom then the partition table most likely is ok.
Tried that. Didn't help. When I flash a ROM i check /system and it's empty. No matter what ROM, no matter which recovery
I don't think it's the PIT now. /system seems to be read only. How do I change the permissions via ADB?
Sent from my Lenovo S6000L-F using XDA Free mobile app
Just wanted to say: I have the same issue now. It's not that critical as I have long moved on from this phone and only experiment, but same behavior here. Have tried many things to no avail (recoveries, ROMs, stock firmwares, etc.).
nazfalas said:
Just wanted to say: I have the same issue now. It's not that critical as I have long moved on from this phone and only experiment, but same behavior here. Have tried many things to no avail (recoveries, ROMs, stock firmwares, etc.).
Click to expand...
Click to collapse
If ANYONE can come up with a solutions that works i'll donate for a beer or cup of coffe. I'm currently running Stock 4.4.4 with CF Root. Better than nothing. But i miss 5.1.1
BelugaHval said:
If ANYONE can come up with a solutions that works i'll donate for a beer or cup of coffe. I'm currently running Stock 4.4.4 with CF Root. Better than nothing. But i miss 5.1.1
Click to expand...
Click to collapse
Anyway here's what i've been trying:
Recoveries: PhilZ, CWM, TWRP
Custom ROMS: well amost all there are...
Stock ROM
Tried repartitioning with PIT
Erasing NAND
I checked the permissions on /system and they are as they should be
I fixed it (not really sure how) ... i ran stock for a while and decided to try again. This time with CWM. Now all is good and i'm back on NAMELESS :good:
BelugaHval said:
I fixed it (not really sure how) ...
Click to expand...
Click to collapse
Fine, welcome back to the modern world! ☺
But it's sad that you can't tell what fixed the situation. Would have been good to know.
GhouLinux said:
Fine, welcome back to the modern world!
But it's sad that you can't tell what fixed the situation. Would have been good to know.
Click to expand...
Click to collapse
1. Flashed 4.4.4 nordic version of stock (I9305XXUFNL1_I9305DNFFOB1_I9305XXUFOA1) in ODIN, and let it complete with its setup-wizards and so forth
2. Flashed clockworkmod for i9305 (v. 6.0.4.5) via ODIN
3. I flashed nameless nightly 09.07.2015 in cwm and booted it (without gapps)
4. Rebooted back to recovery and installed tk-gapps.
5. Well everything works
BUT before i did that i did all kinds of stuff, like repartitioning with a PIT file and erased NAND in ODIN.
Not sure if the repartitioning and NAND erasure had anything to do with the success.
I still get the "unmount of /system failed no such volume" when flashing in CWM. But the difference between before and now, is that it actually puts stuff in the /system dir It didn't before. I'm too scared now to change the recovery, although i prefer TWRP. So i'll let CWM be.
BelugaHval said:
1. Flashed 4.4.4 nordic version of stock (I9305XXUFNL1_I9305DNFFOB1_I9305XXUFOA1) in ODIN, and let it complete with its setup-wizards and so forth
2. Flashed clockworkmod for i9305 (v. 6.0.4.5) via ODIN
3. I flashed nameless nightly 09.07.2015 in cwm and booted it (without gapps)
4. Rebooted back to recovery and installed tk-gapps.
5. Well everything works
BUT before i did that i did all kinds of stuff, like repartitioning with a PIT file and erased NAND in ODIN.
Not sure if the repartitioning and NAND erasure had anything to do with the success.
I still get the "unmount of /system failed no such volume" when flashing in CWM. But the difference between before and now, is that it actually puts stuff in the /system dir It didn't before. I'm too scared now to change the recovery, although i prefer TWRP. So i'll let CWM be.
Click to expand...
Click to collapse
Will try this procedure and report back. I think this should be moved to Q&A, though.
Edit:
Using CWM I was able to flash and boot NamelessROM, as well.

Categories

Resources