Related
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
I have the same issue. I was tryint to load Cognition and it just gets stuck on the ATT screen but I haven't tried a jig yet. I was wondering if I can replace the files on the phone with good files that aren't corrupted and see if it boots up because droid explorere can still pick up the phone and so does Odin but when I do a master reset nothing happens.
@rajasekhar - Have you tried: Removing all parts (battery, sim, sd) let it sit for a few min (my preference is around 10 min to insure no residual power is left in the system) then hold the jig in place and putting the battery back in? Keeping the jig in place, so that as soon as the device gets power it is immediately seeing the jig, before it can try any other processes.
A bit difficult to do with hand made jigs I know. If you still getting nothing then your in for the worst and the phone need a JTAG or service center visit.
Tho it sounds a little odd that it could boot up to seeing the AT&T logo, but does not respond to the jig. Might even be a hardware problem.
@i3oots - Since you say your still getting PC response your safe to try and reflash it or just pick something different altogether. Tho you might wanna let ODIN settle and just sit there doing nothing for a few min, w/o then w/ the phone plugged in. Or learn about Heimdall and go that route.
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
You have probably Hard Bricked your phone. A JIG will not work to recover the phone. If the phone has any life at all, then the JIG will work. Else, u hard bricked it...you should never remove the usb cable when flashing bootloaders or odin or anything!
the only solution is to get a JTAG which can recover hard bricks OR you can go to a warranty store (don't know about india) and make up a sob story and have them replace it..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
Does your computer recognize the phone? If odin is open, does the box turn yellow when you connect your phone? Make sure you have the right drivers. I think cm7 and captivate drivers are different. Keep trying with the jig. Just because you can't see anything on the screen doesn't mean the phone is dead.
i3oots said:
Would I be able to flash it even though it get's stuck on the ATT screen? It won't go into download mode. I'll look on the forums how to flash it too. I'm a newb at this which is why I bricked it but everyone has to start somewhere lol.
Click to expand...
Click to collapse
If your phone is booting up far enough to send out USB info for ODIN and other PC programs to see it, then your still in a workable condition. This also means you can still get into download mode, but since things arn't working properly it will be harder. Depending on which bootloaders your phone has will direct which methods you'll have to try out to get into download mode.
AFTER you've had a chance to look around the forum and self-educate on the different ways of getting into download mode. If your still having problems give us a lil more info of what you were running before the flash and to which version of Cog you were trying to flash.
Did anything worked for you, if not only a jtag can help you looks like u hard bricked the phone.
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
bricked maybe not
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU...... ................................................. I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cant find the original post
rajasekhar19489 said:
Hi guys
@DaNarki : Yea i tried that method to .
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Went for a samsung service centre they said they wont handle other country products of samsung. Just yesterday went to the local Cell phone Repair store , He said like he would try using a Ctool box they have for installin onto the rom directly. So i thought why not Give a shot to it ...
That store guy raised another question in me . Yesterday after giving it in the morning he said to call in the evening . I did so and he said the Phone is booting on the Ctool but it is sometimes throwing error . I dint get his intention in saying so . have to go to him today
Click to expand...
Click to collapse
rajasekhar19489 said:
Thanx for ur suggestions guys .I really squeezed through xda for all possible ways of unbricking but no use. SO thought JTAG was the only option.But wanna know more about JTAG???????
Click to expand...
Click to collapse
If you just wanna know a bit about the process ask this guy. He is pretty much the only person in the US (I know not all to useful to a person in India) that does JTAG for the cappy.
I can tell you this much, it requires a special device called a Riff box and it sends boot info directly to the chip on the main/mother board that is used for the booting process.
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
malebornin69 said:
I thought I was bricked also ...HARD BRICKED......no buttons no nothing ...tried odin on, phone plugged in, and hold down volume up and down and reinstall batt......nothing worked.......but this... it worked for me........ok first of all remember this will be a bit tricky because you will have to keep the volume keys pressed the whole time till you have download mode......should also have full batt......take out the sim and any flash cards you may have in the phone and the batt.....set the phone down and watch a couple hours of tv or try to brick your buddies phone so he can feel your pain...lol something.....ok now after your tv show has gone off turn on your computer and start up odin one click to stock.... put just the batt in the phone.....if your friend is still there you should try this with 100% batt.... use his phone to charge your batt.....any way put the batt in the phone....plug the usb cable into your computer......now for the tricky part .......press down the volume up and down now and do not let them go till the end of this and you should have download mode.......now plug in the usb to your phone IF YOU HAPPEN TO GET DL MODE HERE THEN GO AHEAD AND LET GO OF THE VOLUME BUTTONS AND FLASH YOUR PHONE ....if not... KEEP THE BUTTONS PRESSED.......now take the batt out of the phone.....keep them pressed......unplug your usb cable......keep them pressed.... restart odin...... keep them pressed....plug your usb cable back in.......keep them pressed... re-install the batt.....you should get download mode.......remember you have to keep them pressed... JUST... the volume up and down pressed through the whole process nothing else....This worked for me and I was dead bricked no nothing from any of the keys no nothing..... I DIDNT INVENT THIS METHOD I READ IT ON HERE SOMEWHERE AND CANT FIND IT AGAIN......It did work for me when nothing else did.....so if the person that posted it reads this THANK YOU......
Click to expand...
Click to collapse
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
DaNaRkI said:
Somewhere I've seen a site that listed info of ppl around the world that will JTAG, but I can't seem to find it right now.
Click to expand...
Click to collapse
Thanx DaNaRkI .. hmm well i would now again start digging the threads for seeing wat u have suggested ..
rajasekhar19489 said:
HI,
I am from INDIA, few months back I got a Samsung Captivate , Till now i tried FIREFLY and CM7 ROMs . The first time flash i did it with ODIN i guess i did it with a wrong firmware ,So was stuck with AT&T screen boot loop issue. Searching the forums and found JIG may help and so made a JIG (as i can't get one here) . and recovered my phone and flashed stock and then FIREFLY and 2 weeks back i flashed CM7 for getting Gingerbread and not likeing the UI of the ROM tried to switch back to stock and then customize on my own.
So When i tried flashing Stock the installation was success the screen stuck few moments on AT&T logo and i thought it would go off, But as i was very eager to get my phone online again i pulled of the battery to restart manually (Which i dont think was nice idea ) Now the screen remains black even i use the JIG to get into download mode. But the phone heats UP when i plug it for charging on computer or directly to switch
HELP NEEDED as i am very addicted to this PHONE
Click to expand...
Click to collapse
hello brother,,
u can find the Jig here in india... i also purchased... and it worked for me..
Download-Mode-USB-Jig
press thanx if it helps..
rajasekhar19489 said:
Thanx MAN!!!!!! . it seems interesting method to try .. but i have to wait 12 hrs to get my phone back from the guy i gave to repair that. he said his chances of getting it fixed are 50-50 so i might as well prepare for your method to ..
Click to expand...
Click to collapse
Hope it helps I wish I could find the original post again to thank the guy that told me how to do it. I had sent that phone back to att and the promptly sent it back and told me the water dammage sticker in the bat compartment was missing and they wanted to charge me 409 bucks for the phone ....long story short it was there when I sent it and I told them to go pound sand up their ass because I wasnt paying them that much and ended up paying 125 bucks for a paper weight.So that is when I decided to have it jtaged but figured I would give it one more shot before mailing it off. That was when I found the post from that person and low and behold it worked........................... I hate to say this but I may have got the last two instructions backward you may have to put the batt in before plugging in the usb cable.......Like I said I cat find the original post
malebornin69 said:
Hope it helps
Click to expand...
Click to collapse
Buddy tried it ... Thanx for that..But dint help . Now going for another options i mean in search for other options
But ppl help me with JTAG thing and its users(or developers) availability in india
Forgot to mention
I Missed to explain my flashing procedure i have done this time . Like I never tried flash a boot file along and so was reading some threads about boot loader variations between FROYO and GINGERBREAD so i tried flashing ablong with boot loader and then I got the stock gingerbread file i put the boot loader SBL in heimdall Firstboot loader path .And Boom the first reboot got stuck and i removed the battery and then again when i tried to restart the phone is dead
Thinking this might have where the whole thing went wrong and made the cell dead .
I tried flashing the ics source port but forgot to flash cm7 first... It flashed fine and I followed the procedure to flash. The phone would turn on but always go straight to recovery. I figured this was because I didn't go to cm7 first, so I went to flash it but I kept getting errors. I went to flash stock, it started going so I walked away. When I came back my phone was just a white screen and odin was stuck at sbl.bin. So now I can't boot up the phone, there's no bootloaders, just a black screen whenever I try to do anything. The thing is, I can get into download mode just fine through button combos which leads me to think it's not bricked. However, odin/heimdall will not recognize it... Anyone know what to do?
EDIT: View last post by me.
mikel.canovas said:
I tried flashing the ics source port but forgot to flash cm7 first... It flashed fine and I followed the procedure to flash. The phone would turn on but always go straight to recovery. I figured this was because I didn't go to cm7 first, so I went to flash it but I kept getting errors. I went to flash stock, it started going so I walked away. When I came back my phone was just a white screen and odin was stuck at sbl.bin. So now I can't boot up the phone, there's no bootloaders, just a black screen whenever I try to do anything. The thing is, I can get into download mode just fine through button combos which leads me to think it's not bricked. However, odin/heimdall will not recognize it... Anyone know what to do?
Click to expand...
Click to collapse
Try the things listed in the "connectivity issues" post attached to my signature. If none of those works to get Odin/Heimdall to see your phone, post back.
followed it. Didn't recognize for like a minute then it showed up. I started it but it's stuck at do not turn off the target
tried again and same thing
What is it showing on the computer side (i.e. what is Odin/Heimdall saying right now)?
I'm using odin right now. But heimdal would always just say not recognized or whatever it says. Odin, when I get it to finally recognize after waiting a minute using your method, it just gets to DO NOT TURN OFF TARGET! and stalls there.
I got it to work. No clue what made it finally work
mikel.canovas said:
I got it to work. No clue what made it finally work
Click to expand...
Click to collapse
Good to hear. I know the feeling - it's like the computer/phone are just messing with you.
Damn. A similar thing happened. I had to flash to stock since button combos weren't working, and all the sudden while odin was running my screen just went black. I waited to see if anything would happen, but everything just stalled there. I've been trying to use my homemade 100k ohm resistor jig, and button combos to get into download mode but nothing seems to be doing anything. Am I bricked?
If u have no signs of life at all (no battery charging screen when u plug into a wall charger or no kind of something happening if u try to power it on) then u r hard bricked.
But there is Jtag and the Unbrickable Mod.
4-2ndtwin said:
If u have no signs of life at all (no battery charging screen when u plug into a wall charger or no kind of something happening if u try to power it on) then u r hard bricked.
But there is Jtag and the Unbrickable Mod.
Click to expand...
Click to collapse
Thanks, not what I wanted to hear. But okay.
mikel.canovas said:
Thanks, not what I wanted to hear. But okay.
Click to expand...
Click to collapse
Its cheap and keeps your phone from ever being unrecoverable again, it is better than paying the $150 for a replacement.
Sent from my I897 using xda premium
Yeah and seeing as how I'm planning on doing a bunch of development on it once I get another phone, I'm probably going to need it.
I have it and it does come in handy
Sent from my I897 using xda premium
mikel.canovas said:
Yeah and seeing as how I'm planning on doing a bunch of development on it once I get another phone, I'm probably going to need it.
Click to expand...
Click to collapse
Sometimes, if you get a lucky brick, the UnBrickable resurrector will work without any mod. This is rare, but its a shot. If you need a mod and don't have the tools, pm me.
AdamOutler said:
Sometimes, if you get a lucky brick, the UnBrickable resurrector will work without any mod. This is rare, but its a shot. If you need a mod and don't have the tools, pm me.
Click to expand...
Click to collapse
Thanks, will try that next time. Luckily AT&T exchanged it for me
mikel.canovas said:
Thanks, will try that next time. Luckily AT&T exchanged it for me
Click to expand...
Click to collapse
I had something similar happen to me,when I was running A6 or A7. I even noticed that I was losing folders that were visible on CWM. I was going to try to re-flash the ROM, but those folders were gone. What fixed it for me, was I did a Factory Reset, and al of the lost folders came back, and I was able to Odin back to stock. I was one of the more weird things I'd seen with my Cap
Hello people,
I have searched a lot on google en XDA to solve my problem, but i can't find it. The temperature of my Samsung Galaxy s GT-i9000 is to low, to be exact -7° degrees.
The problem is that i can't charge my phone now. The phone says: Charging paused. Battery temperature is too high or too low.
Can anyone help me, is would appreciate it a lot!
That's unusual to be honest ^^ , maybe if you put your phone ( or the battery ) in a worm place this problem will be solved , lol i can't even imagine what you've done to make it -7degrees ..
If the temperature of the phone is nrml and you're getting this msg for no reason u can reset it to factory settings , this will probably fix any software problems.
Good luck
i have reset a lot of times my factory settings. Do you have more solutions? (sorry for my English, i speak dutch) Thanks
did u flash any rom?
How old is your phone(battery)
Try a factory wipe,as suggested in the above post,maybe it's an app that caused the prob
I know for sure it's not my battery because had a other battery in it and it said the same. What i was forgotten to say was that my computer recognize my phone as a samsung galaxy, that is really strange. He doesn't want to charge.
Can you manage to get into recovery mode (by clicking vol up+home+power)? If you can, go to "advanced>wipe battery stats", and see if that fixes the problem.
did u flash any rom(kernel) if not,then I think your battery chipset is broken.
If u did flash any rom try format your system in recovery and flash a new rom first from cwm and if this doesn't fix then format again and flash a rom with Odin
Good luck
Yes i can it didn't work. Could a Kernel help me? Or has anyone have a link to rom which could help me?
Stock rom(jvu) get it from sammobile.com or search for darky's rom and flash this through ODIN.if u never tried odin then search and read how to use it
Thanks i'll try to install the darky rom. I tell you if it helps and when it doesn't i tell is also.
Have you flashed custom rom before? If yes try darky or something. If no is your phone still under warranty? If yes don' t flash anything and take it in. If no flash darky or other rom to see if you can resolve issue.
Sent from my GT-P7500 using Tapatalk 2
Thanx ,cos I never heard of this problem before,so it would be nice with a follow up
Hope u will get fixed.
Good luck m8
Sorry m8 it didn't work. I installed the darky rom and the problem is still there. I installed the Rom by CWM recovery. It couldn't work with odin
Could anyone help me with this problem?
Use darky's 10.2 TAR file this is flashable with Odin or any other .tar file.
@RAMAD rooted roms is tar and only flashed in Odin.search ramad
it diden't work. Could it be solved with a secret code or something? I don't think it is a hardware problem because i can connect with my computer.
dubbelr said:
it diden't work. Could it be solved with a secret code or something? I don't think it is a hardware problem because i can connect with my computer.
Click to expand...
Click to collapse
Hi, did you find a solution to the problem? I have the same problem after leaving my phone in a hammock in the rain (probably not the greatest of ideas). The phone works fine, but won't charge the battery. My solution so far was to buy a separate charger to charge the battery (about $10 from Amazon), but if there is a way to stop the battery check that would be much better than having to take out the battery every day to charge it.
Regards,
Svein
svein.berg said:
Hi, did you find a solution to the problem? I have the same problem after leaving my phone in a hammock in the rain (probably not the greatest of ideas). The phone works fine, but won't charge the battery. My solution so far was to buy a separate charger to charge the battery (about $10 from Amazon), but if there is a way to stop the battery check that would be much better than having to take out the battery every day to charge it.
Regards,
Svein
Click to expand...
Click to collapse
I'm having the same issue. It just started yesterday. Even with low use the phone gets hot and it won't let me charge it. I keep getting the battery temperature error. Even when it's powered off. I went into recovery mode as suggested by a previous poster and there is no advanced options that I can see. I'm not rooted and bone stock. Very frustrating. I've also tried another OEM battery to no avail.
HELP! http://forum.xda-developers.com/ima charging paused battery temperature too low
Hello guys, I get that message whenever I charge it or connect it to PC
my phone is galaxy s2 and the ROM is ICS 4.0.4
if anyone can help me. THanks
The problem is in the charge port flex it self. i work for a cell phone repair shop. i fix this issue all the time. its just a trac on the flex that goes bad. easy replacement fix. Here is a link to buy one.
http://www.ebay.com/itm/USB-Charge-...e_Replacement_Parts_Tools&hash=item3a841732e2
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
hav0c said:
You probably end up going to Samsung. Pay €200 and get a new motherboard.
Good luck.
Sent from my CM9 GT-N7000 using XDA premium
Click to expand...
Click to collapse
WOW...
the problem is that i live in a fu**ed up country and we dont have samsung here.
all phones come without warranty and by smuggling from other countries
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Dude, if you have no way of repairing a bricked phone in your country then stay away from flashing custom ROMs!!!
Sent from my superior GT-N7000 using Tapatalk
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
i love my note so much that if i couldnt fix it i think im gonna kill myself.
let me tell you the whole story, maybe you can revive my note again.
im a daily rom flasher, sometimes even 2 or 3 roms a day,
i wanted to flash ics stunner rom so i went into cwm recovery,flashed the zip file and wanted to format data\factory reset, but while the phone was formatting i accidently pressed the power button, the phone was stuck and didn't complete formatting, i took the battery out, put it back in and powered the phone, it was stuck at the bootscreen GTn7000 Galaxy Note.
I got into download mode and flashed a stock rom, but it was the same.
i downloaded and flashed other stock roms but it was stuck at the bootscreen.
then i wanted to flash a stock rom that came with a Pit file, i did everythig correctly, and Odin was stuck at the partition thing, for more than 15 minutes.
i unpluged the phone i pressed the power button, NOTHING!!
i officially bricked my phone which i worked so hard for months to get it.
i tried everything,even the jig thing, i couldn't buy so i had to make one.
maybe i did somethig wrong with the jig or maybe because i didnt solder it or the usb plug im using isnt working.
this may be relevant, i pluged the usb OTG in the phone and in the OTG was a bluetooth peice for computers, the piece had a light, and the light was ON.
Another thing that if i leave the battery in the phone for a while, the camera area in the back gets a little hot, my phone always did that meaning its still alive.
i may have written too much, forgive me but im really desperate.
Thanks in advance.
Click to expand...
Click to collapse
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
izzmohamed said:
Hi everybody, I searched everywhere for a solution but no luck
Click to expand...
Click to collapse
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
octavian90 said:
You mentioned killing yourself. Bro it's just a phone... Hang in there!!!
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
if you had gone through what i went through to get the phone, you would probably do the same.Thanks for the reply, any thing would help me right now.
vijai2011 said:
First thing donot flash Ics now untill you are craze about it.2nd donot use CWM as much as possible.Read this.
Ok to the problem now.Since you say it gets hot,it might be still alive.Remove the battery and insert it after 10 secs and insert the jig and after few secs press vol up button.Now connect the phone to computer and see if its detected if it does try flashing abyy's kernel.I dont know which kernel for sure.Somebody might help you.People were able to get into DL mode when there screen were not showing anything.
Click to expand...
Click to collapse
Thanks man, i will definitely try it right away.
mother board
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
chasmodo said:
There are situations when your phone is working, but your screen is black.
Let's hope yours is one of those...Try this:
1. Don't flash Abyss. Download a stock GB Rom instead.
2. Charge your phone for a couple of hours. You need your battery for the
following steps.
3. After charging, take out your battery and wait 1 minute
4. Put it back in
5. Boot into Download mode (Volume Down+Home+Power) (you will see only black screen)
6. Count to 10
7. Press Volume Up
8. Count to 10
9. Start your PC Odin
10. Connect your phone to PC
11. Wait untill PC installs the necessary drivers
12. If all goes well, your PC Odin will flash the yellow light with COM info in it
13. Flash your stock GB Rom
If this doesn't work, you'll need to think of the ways of getting your phone JTagged or where to get a new motherboard.
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
kvsandeepreddy said:
Bro as u mentioned already that u flashed stock once...all root and cmw will be wiped... i would prefer going to samsung service center and tell them that u were updating your phone through kies and after the update completed ur phone stopped working... they will fix it for free... and act innocent
Edit::: dint see the other post where u mentioned that there is no samsung center at your place... in that case theres only one thing u can do... buy the motherboard and fix it urself.... sorry that ur beast is dead
Click to expand...
Click to collapse
MR.change said:
Your phone is pretty much dead I'm afraid
Why didn't you bother to read stickies first?
It has been known for several weeks now that doing a wipe from CWM in a leaked recovery (I.e all ICS ROMs except cm9 official) will lead to a corrupted emmc drive ,thus a dead phone
And no ,you pressing the power button had nothing to do with it being stuck
The moment you hit wipe from ICS stunner's recovery your phone was dommed.
Anyway what's done is done ,now find an unofficial repair shop and replace your motherboard.
I hope this makes it clear ,and good luck to you.
Click to expand...
Click to collapse
pvillasuso said:
Try this : http://forum.xda-developers.com/showthread.php?t=1257434
To force your phone into Download mode !
Click to expand...
Click to collapse
You guys are awesome, im gonna do everything you said and get back with the results, fingers crossed.
I have a friend who's going to Dubai,UAE in a week or so. if nothing worked i'll send the phone with her to repair it at samsung,does anybody know if there's a samsung service center in Dubai and give me the location ?
i cant thank you enough,really appreciate all the help.
firasusman said:
mother board is gone due to kernel harm of ics leak
sorry
this is the fact...
Click to expand...
Click to collapse
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Try a different USB cable?
Sent from my SPH-D710 using XDA
izzmohamed said:
OK, how much will it cost me ?
by the way i forgot to mention that before i bricked the note, it had a charging problem, saying voltage too high,charging stopped,and when the phone is turned off the battery icon keeps appearing and disapearing, could it be that the jig is not working because of that??
Click to expand...
Click to collapse
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
jeffrey567 said:
Try a different USB cable?
Sent from my SPH-D710 using XDA
Click to expand...
Click to collapse
I did, still the same.
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Hmmm,i'll try cleaning it.I had the same situation, so the jig should work fine despite this problem ?
jayshah said:
You're not going to like this: I had to send my phone back to Samsung to get that fixed. Basically the charging port was shorting out, happens when stuff gets inside it (dirt, moisture, etc, from what I read). You could try cleaning it, but for me the port didn't break, it just acted like it was charging when there was nothing plugged in. So the JIG will work if it's supposed to.
Click to expand...
Click to collapse
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
lanwarrior said:
Just out of curiosity: Are you in the US and had to send your international Note somewhere? I am wondering how one can get a support for an International Note if you're in the US.
I don't mind sending it to another country, but which Samsung center will accept it?
Click to expand...
Click to collapse
I am wondering the same thing, mine got bricked about a week ago and I don't really know what to do with it
Yesterday evening my phone was on the charger then it suddenly stopped and it is completely dead. It isn't showing any signs of life ever since, even if I charge it. It doesn't even show offline charging and I can't send it to Samsung as it's rooted so my warranty it VOID. It seems to me that it has Sudden Death Syndrome because it has been recently been switching off and now it's completely dead. What should I do? I'm pretty much screwed!
KoolKid98189 said:
Yesterday evening my phone was on the charger then it suddenly stopped and it is completely dead. It isn't showing any signs of life ever since, even if I charge it. It doesn't even show offline charging and I can't send it to Samsung as it's rooted so my warranty it VOID. It seems to me that it has Sudden Death Syndrome because it has been recently been switching off and now it's completely dead. What should I do? I'm pretty much screwed!
Click to expand...
Click to collapse
Can you enter download mode?
robintjeuuu said:
Can you enter download mode?
Click to expand...
Click to collapse
Well... I managed to just get it into offline charging. When I boot it up in normal mode it shows Samsung Galaxy S3 mini then after a few seconds the bottom lights flash for half a second and shut down. When I try to boot to recovery, model name then shut down. Yes it can just about make it into download mode.
KoolKid98189 said:
Well... I managed to just get it into offline charging. When I boot it up in normal mode it shows Samsung Galaxy S3 mini then after a few seconds the bottom lights flash for half a second and shut down. When I try to boot to recovery, model name then shut down. Yes it can just about make it into download mode.
Click to expand...
Click to collapse
If you get into download mode, go to sammobile en download the firmware for your phone and flash it with odin. if that worked, open stock recovery and do a fatory reset to make sure everything is back to stock... Then you can just hope it won't happen again.
robintjeuuu said:
If you get into download mode, go to sammobile en download the firmware for your phone and flash it with odin. if that worked, open stock recovery and do a fatory reset to make sure everything is back to stock... Then you can just hope it won't happen again.
Click to expand...
Click to collapse
I tried flashing stock recovery and ROM through Odin, it said pass but nothing actually seemed to fix and it still has the same problem that it shuts down after showing logo and when I boot to recovery it just shows TeamWin for a few seconds and shuts down so looks like I'm screwed and I have to use my BlackBerry :'(
KoolKid98189 said:
I tried flashing stock recovery and ROM through Odin, it said pass but nothing actually seemed to fix and it still has the same problem that it shuts down after showing logo and when I boot to recovery it just shows TeamWin for a few seconds and shuts down so looks like I'm screwed and I have to use my BlackBerry :'(
Click to expand...
Click to collapse
Ok, can't help you, maybe search this forum for unbrick device. I know there are fixes that can be used with some bricks.
robintjeuuu said:
Ok, can't help you, maybe search this forum for unbrick device. I know there are fixes that can be used with some bricks.
Click to expand...
Click to collapse
And I don't think Samsung will repair it as my warranty is void and I doubt if my parents would get me a new phone as this phone is only 3 months as well! And I have seen an unbrick thread and I tried it and it didn't work :'(
Well, I know how you feel. My charging port died once after I changed rom. Samsung asked me 200 for repair. Maybe you can give it a try and send him in... You never know Samsung loves you more than me..
Sent from my GT-I8190 using Tapatalk
robintjeuuu said:
Well, I know how you feel. My charging port died once after I changed rom. Samsung asked me 200 for repair. Maybe you can give it a try and send him in... You never know Samsung loves you more than me..
Sent from my GT-I8190 using Tapatalk
Click to expand...
Click to collapse
My dad took it to the service centre and they said they can't fix it as it's rooted so I'm screwed :'(
sunny296 said:
thanks,this index help me out very much.
Click to expand...
Click to collapse
What do you mean?
Zamoro1 said:
it is not samsung galaxy problem. it was your problem. you must close your downloading and other working while it is on charging.
Click to expand...
Click to collapse
It wasn't downloading anything?
Don't worry everyone I sent it to a repair shop (not Samsung) so I hope they manage to fix it.
Mine also dead
KoolKid98189 said:
Don't worry everyone I sent it to a repair shop (not Samsung) so I hope they manage to fix it.
Click to expand...
Click to collapse
Have you any news about the problem in your phone?
Mine (i8190 with one of the mclaws roms from previous week) also appeared in the morning shut down and there's no way of starting it. It does not even vibrate when power button pressed, as if the battery was completely empty.
Tried with another battery and checked that the original one had charge, but no luck. It does not start (normal, download or recovery, makes no difference).
Any ideas?
PelosBi said:
Have you any news about the problem in your phone?
Mine (i8190 with one of the mclaws roms from previous week) also appeared in the morning shut down and there's no way of starting it. It does not even vibrate when power button pressed, as if the battery was completely empty.
Tried with another battery and checked that the original one had charge, but no luck. It does not start (normal, download or recovery, makes no difference).
Any ideas?
Click to expand...
Click to collapse
Well mine was dead for a day then I plugged it into the charger (this was after a day and I left it on charge all night and it wouldn't start) and I held the power button for 10 seconds while it was on the charger it showed offline charging so I let it charge for a bit and then I powered it on and it seemed to be bricked so I sent it to a phone repair shop (not Samsung as my warranty is void). If it doesn't show any signs of life then it's bricked. If it comes to life then it is also probably bricked. I tried flashing many recoveries, ROMs, kernels and params and nothing happened.
In the S III Mini General forum there are topics about getting your phone back to stock so that it is covered by warranty.
james.faction said:
In the S III Mini General forum there are topics about getting your phone back to stock so that it is covered by warranty.
Click to expand...
Click to collapse
I tried to flash stock ROM and recovery but nothing actually worked!
1. Did you follow the instructions in detail?
2. What does "nothing actually worked!!" mean??
Maybe you need to work out what is the problem and why it is failing. Then you will be able to figure out if it is actually fixable, and if so how to fix it. "Trying everything" doesn't really work unless you make an effort to analyse the results you get every time you try something.
You could try posting in one of the threads about taking the phone back to stock. The people who posted them might be able to help you, they are more experienced at this sort of thing.
james.faction said:
1. Did you follow the instructions in detail?
2. What does "nothing actually worked!!" mean??
Maybe you need to work out what is the problem and why it is failing. Then you will be able to figure out if it is actually fixable, and if so how to fix it. "Trying everything" doesn't really work unless you make an effort to analyse the results you get every time you try something.
You could try posting in one of the threads about taking the phone back to stock. The people who posted them might be able to help you, they are more experienced at this sort of thing.
Click to expand...
Click to collapse
I tried those solutions and they didn't work.
Kid, can you read?
What did you try? What was the result?
"didn't work" isn't a result, it's you giving up. Without even trying to find out why it didn't work.
james.faction said:
Kid, can you read?
What did you try? What was the result?
"didn't work" isn't a result, it's you giving up. Without even trying to find out why it didn't work.
Click to expand...
Click to collapse
I read all instructions, and when I flashed it via Odin, nothing actually changed even with the params!