Replacing housing on Note 3? - AT&T Galaxy Note 3 Q&A, Help & Troubleshooting

I have some scuffs on the chrome plastic around the Note and because I'm OCD, want to repair it but cannot find what part it is. I watched ifixit and etradesupply but I'm not sure which part I have to replace, does anyone know? Thanks.
Sent from my SAMSUNG-SM-N900A using xda app-developers app

Sir_Zuul said:
I have some scuffs on the chrome plastic around the Note and because I'm OCD, want to repair it but cannot find what part it is. I watched ifixit and etradesupply but I'm not sure which part I have to replace, does anyone know? Thanks.
Sent from my SAMSUNG-SM-N900A using xda app-developers app
Click to expand...
Click to collapse
Don't know the part number but I picked one up off eBay for less than $20 shipped. Just don't trash your screen like I did during the install. Had to buy a new screen for $240:crying:

redalertlb said:
Don't know the part number but I picked one up off eBay for less than $20 shipped. Just don't trash your screen like I did during the install. Had to buy a new screen for $240:crying:
Click to expand...
Click to collapse
Yeah, I'm assuming it's all one piece and is the housing I'm looking for. How did you trash your screen? Did a cable tear or something?

http://www.etradesupply.com/samsung-galaxy-note-3-sm-n900a-front-housing.html
This is the part you're wanting. You can get the whole shebang for like 275. At least then you don't possibly botch the screen and need to replace it all and do the gluing etc.
****
Basically, you CAN buy just the housing, but you will have to remove all the hardware (motherboard, etc) from the back of the old one, then using a heat gun/hair dryer, seperate the glass/LED screen/digitizer from the housing, and then re-glue the glass/LED screen/digitizer to the new housing, reattaching the motherboard, etc. You also have to worry about the capacitive buttons at the bottom. And all without doing any damage. Its quite doable, but not necessarily 'easy'.
There are videos of the process all over youtube on various phones like the S3 and S4, as well as the Note 2. And I've seen one or two videos of it being done on a Note 3, however they've destroyed the glass in the ones I've seen. Its not really a recommended process for replacing the housing/bezel, and more for replacing already damaged screens.
However, if you buy the whole shebang for 275, I believe not only do you get the housing along with the pre-attached glass/screen/digitizer, you also get some of the smaller components like USB port and such as well. So you could part out the extra pieces and make up some of the cost.
Either way, there are a few options you have available, ranging from cheap and hard to fix, to expensive and super easy.
GL on the end result!

I was alittle impatient with the hair dryer cracked the digitizer before I even knew it. If you take your time it's not hard if you pay attention to the video.

redalertlb said:
I was alittle impatient with the hair dryer cracked the digitizer before I even knew it. If you take your time it's not hard if you pay attention to the video.
Click to expand...
Click to collapse
This. If you have little patience, don't even attempt it. If you do, go slow, and you should be fine.

Thanks all for the advice and links. I'm rather leery of gluing and possibly messing the screen up, but my insurance plan to get a new phone is less than the completed housing cost. Maybe a case will cover it so I'm not reminded daily of how I failed as a phone parent.
Sent from my SAMSUNG-SM-N900A using xda app-developers app

That was going to be my next response, if its not bad a case is the way to go. The only reason i actually even attemped this was because the back cover wouldnt go back on correctly anymore.

Related

Cracked Glass Screen

A few days ago I cracked the glass screen on my Dinc. There wasn't any significant damage aside from the crack, and my LCD screen is working fine, so I ordered a replacement on Amazon thinking I could replace it. I found a screen which reviewers claimed came with the tools necessary to replace the screens, although the product did not advertise it as such. I made the order to find that the replacement did not come with any tools, and now I am stumped. Does anyone know where I can find cheap (and usable) tools to crack open my Dinc? I was hoping to finish this before I return to college in a few weeks and I'd rather not go back with a broken screen.
Thanks in advance!
Not sure what "tools" you're looking for, but there are only a few things you need to take your dinc apart (I just did this with mine):
1. T6 screwdriver to remove 4 screws on the big red cover
2. A small flat-head screwdriver to release block clips around the big red housing and pop it off. (also used to open up the ribbon cable clips)
3. small philips-head screwdriver to remove screws securing the main board and LCD
4. X-acto knife + hairdryer to remove the digitizer (the glass that you cracked)
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Sounds like you cracked the digitizer yet you ordered a new screen?
m52 power! said:
Sounds like you cracked the digitizer yet you ordered a new screen?
Click to expand...
Click to collapse
Although the sentence structure is somewhat ambiguous, it sounds like he bought the correct replacement part, a digitizer.
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
I'll vouch for this, it's the biggest headache to replace JUST the glass.
Since you already got the glass, you can go ahead and order a bezel by itself if you want... make sure you get one that has adhesive on the metal lip on the inside so the dust won't get in there
swatmedic911 said:
Do yourself a favor and order the digitizer with the frame. It eliminates the need to pry the broken glass out completely. It is a little more expensive, I think I paid $35 for mine, but well worth the time and effort! All in all it took me about an hour to complete mine! BTW, I found and ordered all the parts and tools from amazon.
Click to expand...
Click to collapse
Exactly. I made the mistake of ordering JUST the screen and it was a complete headache. I subsequently ordered the frame/screen combo. Much easier.
Sent from my ADR6300 using XDA App
yeah i replaced mine but now i have trouble with the touch screen not working right. It randomly registers touches on the screen. Hope you don't run in to the same issue.
Glad to hear people are having success replacing these. I have a friend who's cracked his recently and will pass this thread on to him.
I replaced my screen with the digitizer/screen combo bought on amazon for under $20. it's a pain to install, but I found a good video on youtube and used their blowdryer method to make the glue more easy to manage and allow the screen to come off in fewer pieces. Also when you put the little ribbons back into their connectors make sure you get them all the way in - I had 256 color-like graphics for a little bit until I reconnected the screen properly
I've done it multiple times. I'm not clumsy, I just got the phone broken in the first place .
While it would make it easier to get the bezel, it can be done fine with just the digitizer.
They give you all the little plastic tools you need usually.
The last time I did it I used Krazy glue instead of very thin double sided tape.
I can answer any specific questions you have when replacing the digitizer if you want.
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal, but it annoys me a tiny bit that my phone isn't perfect.
Could you record the exact order in which you disassemble it? It might even help you out later
drizzt5;19538891
One request I have for you:
When I put the trackball back into place I wasn't sure if I did the correct order. It still works but it looks a little more recessed then it should be. Not a big deal said:
I just replaced my screen tonight with an amazon digitizer kit and my trackball is also recessed. Might just open it back up and jam some leftover adhesive underneath it. I would recommend buying the frame though as it was a bit of a b*tch prying broken glass shards and adhesive from the thing. Would also make the phone look better as well..
Click to expand...
Click to collapse
i dont have a cracked screen but a very banged up bezel and battery cover. i calculated it and everything will cost me a total of $35 to replace. this includes the digitizer, bezel, battery cover and camera lens. cant wait to get this done.
thanks for the info on here.
Order the digitizer WITH the housing shell. I cracked my screen, too, and ordered the digitizer/screen only and ended up damaging my housing shell. The hairdryer trick is bogus and doesn't work very well, so spend the extra $10 to get the housing.
I was going to repare the screen to resell on Ebay, but since I broke the housing, I decided to just sell the actual AMOLED screen for $40. I'll find other parts I can sell, too, such as the motherboard and camera piece. Might actually end up making more money. Ah well.
I don't use Verizon anymore, which is why I ditched the DInc. Will miss it though. I do love HTC Sense. I have a Samsung Exhibit II now.
My first time doing this was with the digitizer only. Biggest mistake of my life! I could've made it work, but I was getting it replaced since it was bricked and superglue oozing out the sides might have raised some eyebrows. Digitizer+frame, void sticker, and 2 weeks later I had a "new" dinc.

Bionic screen repair

Ok, had a great Thanksgiving until I dropped my Bionic on concrete outside. I guess it landed on the top corner where the power button is, the glass is smashed there and partially missing with major cracks going downwards over half the screen. Miraculously, the LCD display itself is undamaged, only the outer glass. Also the digitizer is still functional. I researched the parts and found that the digitizer and outer glass are one piece on top of the LCD. I couldn't locate any teardown video showing how to take these things apart properly but I did find photos and a new digitizer/glass assembly on E-bay for only $35 bucks. I had sucessfully replaced one of these on a motorola Cliq and figured the Bionic should be easier since it lacks the sliding keyboard. I took a T5 driver and seperation tool and had it disassembeled in 5 minutes. I love how easy it is! I reassembled it until the new screen arrives, hopefully this week.
Since I couldn't find a video of the teardown (and assuming no one else has either) I would be willing to video the job when I replace the screen IF there is sufficient interest.
Sent from my DROID BIONIC using XDA App
Ok, heres the video of the teardown and replacement I did. Enjoy!
Part 1 (Teardown): http://www.youtube.com/watch?v=HqPLk2XNYxs
Part 2 (Re-assembly): http://www.youtube.com/watch?v=q9CMXcVweRU
I would love to see a tear down video. Also where are you getting the replacement parts?
Check ebay for "Bionic digitizer"
Sent from my DROID BIONIC using XDA App
+1 on the video. It would be very helpful.
Ok, I will post a vid to YouTube when the digitizer arrives and post the link in this thread
Sent from my DROID BIONIC using XDA App
I cracked my bionic glass last weekend and just got my replacement screen.
I'm about ready to dig in to fix it, but in reading repair guides for other phones, it appears that the LCD could be glued to the glass. When you had yours open, did you see if the LCD is glued to the glass/digitizer assembly on the Bionic? I'm hesitant to open it up until I know since its still working with the cracks.
I paid $50 at Dealsishop and it came in 7 days.
Love to see your repair guide.
Here you guys go. The glass is not fused to the lcd fyi. Not a video but looks easy enough.
http://www.ifixit.com/Teardown/Motorola-Droid-Bionic-Teardown/6449/1
Thanks - the iFixit teardown was very helpful.
I finished and it works!
My only question is that the glass was stuck to the frame with a thin double stick tape. I tried to re-use it, but there were multiple gasket type shapes that didn't keep their shapes. What do people use for this material?
pasp10 said:
I cracked my bionic glass last weekend and just got my replacement screen.
I'm about ready to dig in to fix it, but in reading repair guides for other phones, it appears that the LCD could be glued to the glass. When you had yours open, did you see if the LCD is glued to the glass/digitizer assembly on the Bionic? I'm hesitant to open it up until I know since its still working with the cracks.
I paid $50 at Dealsishop and it came in 7 days.
Love to see your repair guide.
Click to expand...
Click to collapse
I tore down the phone once, everything but taking the glass out of the frame. The LCD was NOT stuck to the glass/digitizer. The only adhesive material I encountered was the large sticker with the IMEI numbers and such in the battery compartment. That thing actually causes the back piece and underlying piece to stick together. Felt like I was going to bend the pieces when I tried separating them because of that sticker, so I just removed the sticker first and was a lot easier.
pasp10 said:
Thanks - the iFixit teardown was very helpful.
I finished and it works!
My only question is that the glass was stuck to the frame with a thin double stick tape. I tried to re-use it, but there were multiple gasket type shapes that didn't keep their shapes. What do people use for this material?
Click to expand...
Click to collapse
Well I only payed $35 for mine on E-Bay, they say it's OEM part and all, lets hope its the real deal. Also, atleast in the photo, it LOOKS like it includes the entire piece, the frame around the glass and all. Did you get something a little different? Could be the photo is misleading on the E-Bay item too...we will find out soon enough.
http://www.ebay.com/itm/200671887593
Never broke any screens but +1000 for helping community! Your services wont go unapeiciated.
Sent from my DROID BIONIC using xda premium
My glass/digitizer looks the same as the one on ebay. It does not come with the frame around the glass (the part that says Verizon on the bottom). The glass is held in the frame only with double stick tape around the perimeter - works really well because it was tough to get off without damaging the frame. I'm thinking I may need to buy some of that tape and re-do it if it gets loose. Also, there were little gasket-like things around the openings that I couldn't re-use.
questions...
pasp10 said:
My glass/digitizer looks the same as the one on ebay. It does not come with the frame around the glass (the part that says Verizon on the bottom). The glass is held in the frame only with double stick tape around the perimeter - works really well because it was tough to get off without damaging the frame. I'm thinking I may need to buy some of that tape and re-do it if it gets loose. Also, there were little gasket-like things around the openings that I couldn't re-use.
Click to expand...
Click to collapse
So I am about to order the screen and begin the replacement process. Do you think there is enough stick left in the tape to hold the screen to the frame for now? With it put back together, does it force the screen to but up against the frame without the tape doing anything? What does the gasket go around? Did you have to use any of the tools listed in the tear down (besides the t5 screwdriver)
Thanks for the help...
iflysiu said:
So I am about to order the screen and begin the replacement process. Do you think there is enough stick left in the tape to hold the screen to the frame for now? With it put back together, does it force the screen to but up against the frame without the tape doing anything? What does the gasket go around? Did you have to use any of the tools listed in the tear down (besides the t5 screwdriver)
Thanks for the help...
Click to expand...
Click to collapse
The tape is holding for me so far, but I don't think it is right. It's not bulging or anything, but it seems loose in spots. There are holes for the speaker and camera. I'm guessing the gaskets are to keep dust/moisture out. I used the t5 and a couple of plastic tools to separate the parts. The other thing not mentioned in the teardown is that there is a large sticker just below the battery that keeps the back from coming out. I just pulled it back halfway and it releases. Then after everything is reassembled, the sticker can be put back like new.
it's funny,
because the SAME thing happened to me...i am looking fwd to your video/tips on the replacement.
I ordered the glass, and the repair kit online 60bucks total. (prices everywhere have gone up in past 24 -48 hours!)
weird.
The local shop says they can repair for 125 bucks. So hopefully i can do this.
KEEP US POSTED!!
Sam
Done!
Ok, the digitizer/glass arrived today and after a chill with some beers I decided to take a crack at the replacement job.. so please look over my clumsiness.
I experienced the same issues as PASP10 concerning the adhesive for the glass and the slight 'bulging' after the replacement. This is a result of the replacement not being bonded to the frame as well as the original. Everything else is perfect. I will probaly be looking for a kind of epoxy to line the frame with and re-do it later.
Right now, I'm working on converting the HD video of the rebuild I did and uploading to YouTube. Once finished, I will post the link in the 1st post of this thread. Thanks all!
sammyguyana said:
it's funny,
because the SAME thing happened to me...i am looking fwd to your video/tips on the replacement.
I ordered the glass, and the repair kit online 60bucks total. (prices everywhere have gone up in past 24 -48 hours!)
weird.
The local shop says they can repair for 125 bucks. So hopefully i can do this.
KEEP US POSTED!!
Sam
Click to expand...
Click to collapse
These are still $35 bucks on e-Bay.. Did you not check there?
http://www.ebay.com/itm/200671887593
Tear down videos have been posted in first message... loving my shiny new screen again
Sent from my DROID BIONIC using XDA App
thank you!
hey man, that video was great.
I just got my screen in the mail today. Looks good. I am still waiting for the screwdriver repair toolkit.
Can you do me a favor and send me the whole unedited video via pm or something? I could pm you my email addy, thank you!
Sam
sammyguyana said:
hey man, that video was great.
I just got my screen in the mail today. Looks good. I am still waiting for the screwdriver repair toolkit.
Can you do me a favor and send me the whole unedited video via pm or something? I could pm you my email addy, thank you!
Sam
Click to expand...
Click to collapse
Thanks man. I took it back apart later .because I didn't like the "looseness" of the new glass, it was missing the adhesive of the original. I put a small bead of some Plumbers Goop adhesive/sealant around the edge of the frame under the glass since I already had a tube and it seems very close consistency to the original stuff. It worked great
As far as the original video, it was several gigabytes of HD video lol
Sent from my DROID BIONIC using XDA App

Raider digitizer glass shattered, anyone know the proper way to install a new one?

Yes, I already broke my phone. Go ahead, grin and chuckle..now that you've gotten it out of your system, anyone want to offer a little guidance? Never disassembled a newer cellphone before. New glass is ordered and has been shipped, just waiting for it to arrive. I'm hoping the process is fairly simple. I do have a specialized set of screwdrivers with all the hard-to-find bits, so that's not a problem ..it even has the tiny blackberry bit.. but from what I can see HTC uses standard micro Philips screws. Yay for standard formats!
Sent from my HTC PH39100 using xda premium
If this phone is anything like hd2 you're gunna want the flat pry tools they sell (search hd2 screen replacement tools). Their not needed but a nice handy thingy to have, other wise you might crack your LCD from flexing it too much.
Sent from my HTC PH39100 using XDA App
I wont grin and chuckle too much, I broke my Atrix after 4 days.
The Vivid screen seems very fragile. 2 of my coworkers have broken theirs within a few weeks of having them. Small drops from waist distance. Its too bad because I have seen the current Samsung models dropped from 6 feet face first and survive
Sent from my HTC PH39100 using xda premium
Yeah, I've cracked mine as well. If you google HTC raider teardown on YouTube.. There's a vid.... Butttt, it's not in English and it's a teardown not a screen replacement tutorial.
It seems as thought HTC has been using reeeeally thin glass in their devices.
Whered you get the glass? It'd be very thoughtful of you to do a tutorial as you do it. I really want to replacement mine but if you remove one on the screws by the battery it voids your warranty
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
How much is it for them to fix it?
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
travisxcore said:
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
Click to expand...
Click to collapse
I'll do that right now. Thanks alot
(sorry to hijack the thread lol)
They use a double sided tape that hopefully comes with your replacement screen , I tried to replace a water damaged screen and it really wasn't a fun process
Sent from my HTC PH39100 using xda premium
It didn't fall very far..
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
bproulx said:
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
Click to expand...
Click to collapse
So, how was the installation process? And did it come with the adhesive? I'm going to buy it from that site as well
And then it was fixed..! FTW!
Ok sorry for the delay getting back to you guys.. been frantically waiting for the screen to clear US customs (ugh) and arrive, which it finally did today. I was able to get my hands on it at about 3 this afternoon, but I wasn't able to actually look at it until about an hour ago..
So.. I open the package, big grin on my face..and the first thing I notice is that the glass is AT&T branded. Funny, considering I'm in Canada and using Rogers..but hey a digitizer by any other name...and all that. So! I open the bag that my "tools" came in.. There are 2 blue plastic tools, one a prying tool and one looked a lot like a guitar pick. Cool. There are also 2 screwdrivers included, and I'm momentarily excited, until I realize they're just tiny torqx bits. The Raider uses TINY philips head screws, so those were useless. I put them into my tiny tool set..for later consideration.
Back to the screen. Looks like it the real deal, so I watch half of the teardown vid on youtube.. As mentioned in an earlier post it isn't an english-language vid so aside from seeing the locations of the screws and the methods of levering off the internal components, there's no exchange of information going on. I would like to mention however that the video kind of glazes over the locations and removal processes for some sensitive connections, so having only experienced laptop repairs personally.. I was in fairly uncomfortable and unfamiliar territory - but I was determined.
I tried several ways at getting the phone down to its base components, and finally succeeded in locating the panel's ribbon connector interface on one of the phone's circuit boards. I had to remove the back of the phone, pull the batt, sim and sd, and pull the 4 main screws that lock the housing down onto the phone.. From there its a matter of levering off the black plastic shell and whats underneath is a whole lot of tech in a very tight space. There were 3 or 4 wires I had to disconnect, about 15 tiny screws in 3 different lengths, and then when all was said and done I had to pry the busted panel off using the supplied blue lever tool (pretty handy, actually.) and then lift the lcd away from the metal housing enough to slide the old connector out and the new one through.. This was a very tricky process - I drink way too much coffee to hold completely steady for long..lol.. Finally got it all through, but by this time I had smudged the inside of both glass surfaces pretty badly and it took some serious mechanical dexterity to hold the surfaces and wipe them down without wrecking any of the flapping, loose circuit boards, screens, etc.. it was a frightening experience.. I won't lie.. I definitely feared the worst possible outcome given my limited experience.
So.. the panel's ribbon cable is inserted, the white clip back down securing it.. I manage after several attempts to remember how to put the puzzle all back together, and after about 45 minutes of messing with it I had a visually complete phone again. I hit power, and miracle of miracles the HTC logo flashes on the screen.. I'm hopeful..
The phone boots up, looks great (aside from a few smudges I missed on the inside..grr) so I start touching the screen and here's where we have the first problem..lol.. its recognizing that I'm touching the screen..but not really accurately.. it seems to be that there are dead areas.. So now I'm thinking I broke something..lol..
Smoke break.
Took it all apart again, forgot to clean the smudges, removed and re-seated all the connections, and about 15 minutes later I had it back together again. I booted it up and waited.
Success!! It sees where I'm touching accurately now - I think the ribbon must have moved while I was putting it back together, I was shifting things a lot as I was trying to figure it all out, so I must have stressed the cable enough to move it slightly in the slot.. that, or I didn't have it all the way in / straight the first time I did it. Either way, it works fine now. I was successful on the 2nd attempt, and now the only difference is that this glass feels..rougher? less smooth? not sure how to describe it.. it feels different, anyway.. and the at&t logo of course. Aside from that, you'd never know it was in pieces an hour ago..lol.
Would I do this again? ..I hope I don't have to. Its not impossible, but man, if you're going to try this BE SUPER CAREFUL!! lol..
edit: and no - it didn't come with the double sided tape, but it seems to be staying without having to replace it.. it wasn't too hard to remove it from the panel, but getting it back on straight took some finesse.. lol.. it comes apart easier now when you're tryingn to disassemble it..but seems to be holding together fine on its own.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
Corning makes the glass on the Raider/Vivid?
I would suspect it to be more sturdy if its corning, my SGS has been without a screen protector and still does not have any scratches. Yes i know SGS is Gorilla Glass and this is not but i would think it would be stronger.
@ bproulx
You should take it apart again and make a tutorial . I hope i never have to go though what you did. Knock on wood.
lol..might take it apart again..
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
bproulx said:
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
Click to expand...
Click to collapse
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Getting better at taking it apart..lol..
Chism87 said:
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Click to expand...
Click to collapse
No, the little void sticker on mine was less like a sticker and more like... glue, with paint on it.. lol.. it just flaked apart when I tried to lift it.. but I wasn't concerned with preserving it. Maybe if u use an x-acto or something like that you can lift it intact..? Let me know how you do.
I started getting some random touch input glitches yesterday, and today they got worse.. then my son spilled hot coffee on me and I dropped my phone on the carpet where it of course popped apart..lol..and then when I booted it back up I had some *major* touch glitches.. it was seeing input higher up than the actual contact point, and just acting real buggy..the phone was lagging.. so I took it apart again, completely.. took my sweet time reassembling it this time - I even got out the micro-fibre cloth and cleaned all the glass, and voila.. this time - its like new. I can already tell its put together right this time, which tells me something wasn't quite right before - I'm guessing I didn't get the ribbon cable seated properly before.. there are a lot of tiny, offset contacts on the end of that little cable. Anyway, I guess the moral of the story is screw warranties, and the more times you disassemble your phone the better you get at it.. lol.. it wasn't anywhere near as intimidating this time around. Felt kinda easy, actually. I think I just psyched myself into thinking it would be hard to do the first time around.
I do miss my original glass tho.. I'm thinking about contacting HTC and ordering an oem panel lol.. this one feels.. grippy. The HTC one felt smooth as silk.. I dunno this one kinda feels more like window glass. Meh.. better than a broken ghetto phone. At least now I can whip it out in public without hanging my head in shame and peeking around to see who's looking at my ugly screen. I never even tried HTC directly..I just googled the part and went with the one with good reviews..
OMFG...FML..
Sooo.. I got angry at my Raider today.. started doing the weird touch input glitches again after a battery pull, got frustrated and slammed my phone down on the table in anger...and.... smash. Brand new panel is now ten times as shattered as the old one was. AND...now the phone won't even light up. AND..it looks like I may have cracked the actual LCD this time.. just a small crack at the very bottom - wouldn't even be visible with the shell on the phone.. but.. I'm not very optimistic. I get absolutely nothing on my screen when I boot the phone, all I get is one haptic "bump" and thats it. Nada.
Sooo... looks like I need a new phone. Again.
Lame.
There goes $600.00
....sigh.
Anyone wanna donate an old android device to a guy who's now really really sad and has no phone? LOL.. why did I give away my legend????
Not giving up my phone!! LOL!
Ok so I decided to try my luck at replacing the LCD as well as the busted digitizer that I just re-broke..lol.. back to tmart, and ordered both. I really wish I could have found the whole assembly pre-built, but the only company I found selling both as a single unit had a minimum order of 5 pcs. Out of my price range for repairs, although with my track record maybe it wouldn't have been a bad idea? lol.. anyway, I just bought both parts from tmart and am still waiting for one of them to show up. The good news is I was able to replace the LCD already. It really is just held in there with tape. Like.. there's nothing really holding it all together..you'd think with all those screws and tabs they could have come up with a better way?? Ah well. I have a display again, but until I can get the digitizer and install it I'm without input.. so I can just watch the phone boot and then sit on my lock screen. Or boot into recovery mode and use the vol and power buttons to mess about.. But why..lol. I'll just wait.
I'm just happy that nothing else seems to be affected. I had my alarm going off still with no screen, so that tipped me off that everything else should still be ok. I won't know for 100% certain til I complete the repair, but it looks promising. I picked up a used HTC Magic (ugh) from kijiji for $80 and it came with 3 batteries, 3 chargers, 3 usb cables, 3 leather cases, and a bunch of other crap in threes. Just so I'm not completely without a phone in the meantime. Overall not bad for $80 but man is this phone slow. I installed a custom rom **THANKS XDA!!** on it and it improved the performance and look of the OS a little, but it lags a lot even overclocked when just typing a text.. I can't wait to get my phone back!!
Aside from the screens, this phone is pretty tough. I slammed that sucker down pretty hard that day.. Cmon HTC - why didn't you give us gorilla glass on a $600 LTE phone!?!?!?!? I wish I could find an aftermarket panel that was made from gorilla glass. That would totally rock!
Yeah, i really wish they would've put gorilla glass on it. I used to have the atrix and ive dropped it on tile floor at least 3 times... Nothing. Keys in the same pocket as phone.. No scratches at all.
I didn't want to try my luck, so I just got a replacement vivid

Nexus 4 Replacement Parts

I know there aren't any out yet, unless I've missed some, but as the husband of a woman who just had her screen shatter when the phone was dropped it sure would be handy to have on thread where people could post links to parts when they become available.
I think this would make a great sticky so people can start fixing their phones ASAP once parts are out.
Well there is a section for accessories but I don't know of that would help. I am sure though when replacement or after market back plates are available we will hear about it here..
sent via xda premium with nexus 7
There are replacement LCD's on ebay
linelock said:
There are replacement LCD's on ebay
Click to expand...
Click to collapse
Damn, for almsot the price of a new 8GB.. Might as well buy a new one and leave the busted one for parts...
Remeber that the backplate houses the nfc chip along with some of the antennas (not 100% sure on the antennas) so it would be a costly replacement compared to a standard back cover
http://www.parts4repair.com/lg-nexus-4-e960-complete-screen-assembly-without-bezel/
Some parts here.
Sent from my Galaxy Nexus using xda app-developers app
Thanks for the links guys, keep em coming!
Anybody knows where to get a replacement backplate? I broke mine
Replacement screen and digitizer:
http://www.etradesupply.com/oem-lg-nexus-4-e960-lcd-screen-and-digitizer-assembly.html
Anyone see the silver trim (that goes around the front glass) available yet?
Hi
pwkpete said:
Anyone see the silver trim (that goes around the front glass) available yet?
Click to expand...
Click to collapse
If it is anything like the HTC One X and similar phones you usually heat the old LCD glass/display and it unsticks from the main chassis, you then stick the replacement screen back on.
Unless you know what you are doing when replacing the LCD and in some cases have specialist tools and lots of patience, you are probably better off buying a new phone (when you can get them!) and selling the broken one for spares on Ebay.
Back covers may appear. The HTC One X had replacement back covers available quite soon after launch and these contain the antennas, which are little more than sticky bits of foil, and the NFC antenna, for around £28.00 in the UK. The charging antenna is little different to the NFC antenna and they are both together as one part on the Nexus, so that shouldn't make too much difference, but of course there is the glass as well. But hopefully not too expensive given the likelihood of breakages.
Regards
Phil
PhilipL said:
Hi
If it is anything like the HTC One X and similar phones you usually heat the old LCD glass/display and it unsticks from the main chassis, you then stick the replacement screen back on.
Unless you know what you are doing when replacing the LCD and in some cases have specialist tools and lots of patience, you are probably better off buying a new phone (when you can get them!) and selling the broken one for spares on Ebay.
Back covers may appear. The HTC One X had replacement back covers available quite soon after launch and these contain the antennas, which are little more than sticky bits of foil, and the NFC antenna, for around £28.00 in the UK. The charging antenna is little different to the NFC antenna and they are both together as one part on the Nexus, so that shouldn't make too much difference, but of course there is the glass as well. But hopefully not too expensive given the likelihood of breakages.
Regards
Phil
Click to expand...
Click to collapse
Waiting and hoping for replacement backs or a method to replace the glass specifically. My rear glass cracked on the first drop and unfortunately has a crack on the camera lens.
You are definitely correct about the NFC antenna, looking at the iFixit teardown it's just basically some foil glued to plastic. This should not be a major deal breaker in terms of replacement costs.
tgarson said:
Waiting and hoping for replacement backs or a method to replace the glass specifically. My rear glass cracked on the first drop and unfortunately has a crack on the camera lens.
You are definitely correct about the NFC antenna, looking at the iFixit teardown it's just basically some foil glued to plastic. This should not be a major deal breaker in terms of replacement costs.
Click to expand...
Click to collapse
The backs should go for about $30-$40 once prices stabilize, I've taken mine apart and it looks fairly cheap to replace. The Digitizer and Glass (along with the bezel) usually are best when purchased as a solid piece (usually titled "Display with frame") and costs $200+ now and will likely stay $150+ in a couple of years. If you crack your display, mail it LGE as they will fix it up for about $150ish I believe, which is the same price you would pay if you had insurance through Sprint for a cracked digitizer ($150 is the standard deductible for a ~$8 a month insurance plan for the SGS3).
has anyone replaced the screen yet? my phone has slid off surfaces loads and never smashed. however a small bit of sand in my pocket and the damn thing gets scratched. i've had touch screen phones for years and never used a screen protector and never had a single scratch, this is my first "gorilla glass" phone and it gets scratched. looking for how difficult it was to replace?
I wonder when replacement ear piece speakers will become available. Phone is working great except for the crackling ear piece. Hopefully it will be a cheap part and easy fix.
Sent from my Nexus 4 using Tapatalk 2
dnlsmy said:
The backs should go for about $30-$40 once prices stabilize, I've taken mine apart and it looks fairly cheap to replace. The Digitizer and Glass (along with the bezel) usually are best when purchased as a solid piece (usually titled "Display with frame") and costs $200+ now and will likely stay $150+ in a couple of years. If you crack your display, mail it LGE as they will fix it up for about $150ish I believe, which is the same price you would pay if you had insurance through Sprint for a cracked digitizer ($150 is the standard deductible for a ~$8 a month insurance plan for the SGS3).
Click to expand...
Click to collapse
Hey what is LGE? I've had my N4 for almost 2 weeks and just shattered the front glass rendering it unusable. It was on a hard surface and just fell on its own. thanks
bguzmanz2 said:
Hey what is LGE?
Click to expand...
Click to collapse
LGE stands for LG Electronics
I have a Nexus 4 with a cracked screen and broken digitizer! Send me a PM if you're interested.
bguzmanz2 said:
Hey what is LGE? I've had my N4 for almost 2 weeks and just shattered the front glass rendering it unusable. It was on a hard surface and just fell on its own. thanks
Click to expand...
Click to collapse
Just fell on its own? That is a good one!!
Sorry for your loss man. How you get it worked out.
Sent from my Nexus 4 using xda app-developers app
Richieboy67 said:
Just fell on its own? That is a good one!!
Sorry for your loss man. How you get it worked out.
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
Suicidal N4 I guess. I'm glad mine doesn't magically move on its own I must have gotten lucky.
Sent from my Nexus 4 using Xparent Blue Tapatalk 2

So I cracked my screen...

I dropped my phone today and the screen cracked. It's still usable, just has two ugly cracks along the front. Anyone know of a easy way to replace the screen?
treezy26 said:
I dropped my phone today and the screen cracked. It's still usable, just has two ugly cracks along the front. Anyone know of a easy way to replace the screen?
Click to expand...
Click to collapse
send it back to motorola i think they charge 150 to fix
nelsonator1982 said:
send it back to motorola i think they charge 150 to fix
Click to expand...
Click to collapse
Might as well have Motorola replace it, it costs $175 for a new device, but you have to mail them you're busted one first.
Sent from my Nexus 6 using Tapatalk
nelsonator1982 said:
send it back to motorola i think they charge 150 to fix
Click to expand...
Click to collapse
Agreed. I had a similar issue and had an overall good experience with Motorola repair. Took about ten days from start to finish.
Do I just go to there website? I don't have insurance.
treezy26 said:
Do I just go to there website? I don't have insurance.
Click to expand...
Click to collapse
Pretty much. Start at their online repair site:
https://motorola-global-portal.cust...ZS8xNDUxMjUxNzM4L3NpZC9zSnk3cDJGbQ==#/service
So I contacted Motorola and they will fix it for $175 and if I want it back fast I would have to pay another $40 in s/h. With that amount of money, I could just buy a brand new one for another $50. Any thoughts?
treezy26 said:
So I contacted Motorola and they will fix it for $175 and if I want it back fast I would have to pay another $40 in s/h. With that amount of money, I could just buy a brand new one for another $50. Any thoughts?
Click to expand...
Click to collapse
Yes it's 250 on Amazon. Probably a better choice.
Also do yourself a favor and buy a case
OK but now I'm in a dilly of a pickle... I have the option to buy the 6p. My concerns are that the 6 isn't gonna receive anymore love now that it's going on two years old. Would it be wise to purchase the 6 again? Or should I just upgrade to the 6p? I love the 6, I do. But...and yes there's always a but lol. But the 6p intrigues me. I've researched and I know its not much of an upgrade but I love the thought of the fingerprint scanner and the overall look of it. But it is slightly smaller in size and I'm a big dude...but (there it goes again), I could always get a case to make up the difference... Anyways, I would love you guys feedback on my first world dilemma lol. Thanks!
get the 6 and save the money for the next nexus 6 upgrade before the end of next year with a proper cpu like the 820
Sent from my GT-N7000 using Tapatalk
Just an update if anyone cares lol. I went ahead upgraded to the 6p. Farewell my fellow shamu-ers. If anyone is interested in purchasing my 6, pm me. Good day.
If you still have the phone and aren't afraid of breaking it you could try a glass only replacement. I have never done it before until yesterday. I ordered the wire from eBay and made a simple jig to hold the wire so I had both hands. I successfully removed the glass. Hooked it back up still works. Am waiting for the new glass and loca glue (didn't order it until I removed old glass so wasn't waisting money if I broke it. I did practice on 2 junk phones first. Only one of the test screens worked before and it still worked after. YouTube videos is what I followed.
get the 6 and save the money for the next nexus 6 upgrade before the end of next year with a proper cpu like the 820
Sent from my GT-N7000 using Tapatalk
Click to expand...
Click to collapse
This. It's not worth the extra $400 for the 6P just for a bit more dev love.
affiatic said:
If you still have the phone and aren't afraid of breaking it you could try a glass only replacement. I have never done it before until yesterday. I ordered the wire from eBay and made a simple jig to hold the wire so I had both hands. I successfully removed the glass. Hooked it back up still works. Am waiting for the new glass and loca glue (didn't order it until I removed old glass so wasn't waisting money if I broke it. I did practice on 2 junk phones first. Only one of the test screens worked before and it still worked after. YouTube videos is what I followed.
Click to expand...
Click to collapse
Would you care to share your links in what you did?
If better camera and finger print sensor and more comfortable phone in hand is whats important to you i would dive in. I buy 3 phones a year so i can understand you wanting to upgrade even if its not that big of an upgrade . But at this point there won't be any giant leaps from year to year .
treezy26 said:
Would you care to share your links in what you did?
Click to expand...
Click to collapse
Here is a link to glass and t3 torque screwdriver. http://pages.ebay.com/link/?nav=item.view&id=361337407585&alt=web
I got all the parts on ebay. Used the cheapest I could find from us sellers. You need a loca glu. I used a uv flashlight I got on eBay to cure the glue. Have to put it on all parts of glass for about 30 seconds each spot.
Here is the link to the wire I used
http://pages.ebay.com/link/?nav=item.view&id=111281188717&alt=web
I drilled 2 holes in a 2x10 block of wood about 8" apart and put the wire holding sticks in the holes. Watch YouTube videos to see how to take phone apart
It worked pretty good for me. I ended up with 2 small air bubbles under the glass and glass is slightly lifted on one side. Cannot notice once in cheap tpu case.
I used a locktite glue that takes 24hrs to cure to glue screen back to bezel. Cleaned with close pins while curing. Tried double sided tape didn't hold, krazy glue dried to hard didn't hold screen to bezel. I think all my trial and error and scraping and reglueing the bezel is why it is lifted.
Sorry took so long to reply. Just glued the screen on 2 days ago.
And I am in no way saying this is easy just that it was no where near as hard as I thought it would be. You could easily completely break screen trying this
Update. Screen works fine but... The locktite worked the best but is coming undone again. I believe I may have had the loca glu to thick. And made the screen thicker in doing so. And when I put it together it is pressing out. Am thinking of reseperating and reglueing. Any advice is welcomed

Categories

Resources