Related
Think I have bricked my Tab - HELP
Just got myself a Tab P1000. I try updating software using Odin3.
I think i have misused the wrong firmware not for P1000 (stupid), when Odin3 is running gonna finish, it showed FAIL! So i disconnected my GT although the download mode still running.....(stupid again) n I manually off my GT by continuing pressing power button wished to reflash by proper firmware.
As i reconnected it to pc again, although i tried to turned it into download mode again from off mode and i failed, Odin still can detect it. As i tried to use proper firmware to flash it, when it gonna finished, it showed FAIL again!
Now the tab screen turned off and it won't turn on. I tried to turn it into download mode or recovery mode but it couldn't be. I think my wrongly flash has made the buttons all mess up their function. All I have is the LED light on permentanly. If I hold the power button for 10 secs, the LED goes off for 3 secs and then comes on again.
Can anyone help me sort this? Any suggestion pls? Urgent!
Thanks a lot!
What firmware did you flash? I only ask because I know I once flashed an I9000 bootloader on my Captivate and it changed my download & recovery combo to I9000's however they still worked once I used the proper combo (I know extremely lucky)
If bootloaders have been wiped and replaced with wrong bootloaders then its back to samsung with your tab for (hopefully) warranty repair...
Send back to samsung is my last choice, beside this there is no more solution??
my tab it was in same condition, check this forum and you will find solution. i give you what it works for me.....http://forum.xda-developers.com/showthread.php?t=1081800
good luck!!!
Dude!! It is worked!!!!
OMG DUDE IT IS REALLY WORKED!!!
Once i really think my GT have to send back to samsung...... but i have the last try of your suggestion, IT IS WORKED!!!
IT IS SO AMAZING N UNBELIEVABLE!!!
Thanks alot dude!!! You save my SGT!!! n my pocket!!! Thanks~
This solution is really useful n amazing!!
Any1 has same situation can try this!
Thanks again dude~!
Hello,
I tried to flash back to the stock ROM of Galaxy S and then install a new Jetpack 8.2 custom ROM.
Apparently, since I did a bad search on the internet on finding a stock ROM and pit file, i downloaded a pack from xda with the .pit file pda file phone file and CSC file.
I DONT REMEMBER which it was..i selected all the files from the pack through odin and re-partitioning was ticked (i saw it after the flash finished).
So when the processes was completed waited a bit and since the phone was not responding i pulled it out.
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Is there anything i can do to fix it?
p.s: havent tried a usb jig but from searches i made on the internet and on xda forums ppl said it will prolly not work. are there any instruction on how to make one (link would be appriciated)?
Thanks in advance
Best option would be to try a Jig (you can buy one on ebay or dealextreme) and see if you can go into DL mode. Sometime the button combination for Download mode changes depending on the firmware. Try pressing the middle of the volume rocker and power at the same time.
If not wait for a Jib or build yourself one. There should be instruction in this forum on how to build one.
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
evanogrady said:
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
Click to expand...
Click to collapse
Worth a try. Just tell them it suddenly stopped working and you have no idea what's wrong. It's not like they can power it on and see that you failed flashing it or something. and even if they use a jig they can only get to download mode and reflash it...
even if they say no... a jig costs like $1.5 on eBay. search for "i9000 jig".
Insert if, press the power button and poof, you're in download mode,
the thing is that the phone is not under any warranty or something and the store i got it is far away now !!
JTAG service if you're in the UK: http://www.fonefunshop.co.uk/
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
As long as your bootloader is intact, the jig will get you to the download mode
Wrongly flashed i9000 with i897 rom has been confirmed to work with the jig, but i don't know i9000 with i9003 rom...
Or you can apply the unbrickable mod if your phone's warranty was voided already, if not, send it back to the shop.
immortalcy said:
Hello,
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Click to expand...
Click to collapse
Had that also yesterday putting a new ROM on my GS. The process of writing the PDA halted.. Black screen, no way to start it up en no screen indications of charging etc..
I removed it from my USB, Removed the battery a few times did the three way download mode trick several times and finally I got the download mode screen from where I successfully loaded the new ROM.
So try a few times.. even when you get a black screen !!
let me be clear once more..i downloaded a complete I9003 rom pack from xda... some guy posted..i just missed that it was I9003 and not I9000..
and on odin re-partition was clicked..but the process was completed successfully even thou after that the phone wont start or go into download mode :/
i used not only PDA and PIT files but 2 more was included as well :/ so what i am asking is if this could really have damaged the bootloader or not
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
dk206 said:
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Try jig first.
Next try JTAG or UNBRICKABLE mod.
Then Try a service centre.
in case it wokes up.. anyone has links for stock rom and pit to flash with odin?
thanks again
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Taxiozaurus said:
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Click to expand...
Click to collapse
Any updates on this ? cause I'm also having the same issue!
Dan_Aykroyd said:
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
Click to expand...
Click to collapse
Are you 100% sure the JIG wont work if bricked with a black screen. Are there any other possibilities to unbrick the phone. I really need this phone back or my dad will kill me..
Yesterday after unbricked my note from lpy brick (for the 5th time), I tried to flash a stock rom with a pit file (found somewhere on xda, special 16gb pit file for restoring bricked device) but the flash stuck at the begginning so I unplugged it.
Now my phone is unable to go in Download mode, recovery mode neither normal mode.
The screen stay black whatever I do, I've tried all the combinaison possible...
I tried to put it in charge all the night but now the problem is still here.
Any help appreciated
Phenom2 said:
Yesterday after unbricked my note from lpy brick (for the 5th time), I tried to flash a stock rom with a pit file (found somewhere on xda, special 16gb pit file for restoring bricked device) but the flash stuck at the begginning so I unplugged it.
Now my phone is unable to go in Download mode, recovery mode neither normal mode.
The screen stay black whatever I do, I've tried all the combinaison possible...
I tried to put it in charge all the night but now the problem is still here.
Any help appreciated
Click to expand...
Click to collapse
ur phone still ok but u need do manually ...
1st-take out ur battery
2nd-put it back
3rd-Put your Galaxy Note into download mode by holding down Volume Down, Center button, and Power button together for about 10 seconds.
after that press volume up , then connect ur device to odin , flash new fresh rom without pit file
Your phone seems to be totally unresponsive; that sounds like the ultimate hard brick to me.
Take it to the nearest service centre.
USB jig
Did you try putting your phone to download using USB jig ? There are many articles relating to that . Sometimes the phone may not charged when its bricked . So get it charged from somewhere else , or may be from your friend who has note and try using USB jig . It might work , no guarantee , try your luck , else be ready to spend almost half what you paid for your phone to change the motherboard !
ichson said:
ur phone still ok but u need do manually ...
1st-take out ur battery
2nd-put it back
3rd-Put your Galaxy Note into download mode by holding down Volume Down, Center button, and Power button together for about 10 seconds.
after that press volume up , then connect ur device to odin , flash new fresh rom without pit file
Click to expand...
Click to collapse
Already tried... Odin doesn't show me anything... neither adb nor windows..
chasmodo said:
Your phone seems to be totally unresponsive; that sounds like the ultimate hard brick to me.
Take it to the nearest service centre.
Click to expand...
Click to collapse
I have unbricked all my brickeds phones, I think there's always a solution for unbricking it, but if I can't I will take it to SSC
Archangel919 said:
Did you try putting your phone to download using USB jig ? There are many articles relating to that . Sometimes the phone may not charged when its bricked . So get it charged from somewhere else , or may be from your friend who has note and try using USB jig . It might work , no guarantee , try your luck , else be ready to spend almost half what you paid for your phone to change the motherboard !
Click to expand...
Click to collapse
I don't think that the problem is battery, It was 55% yesterday evening, but I haven't friend with a Gnote
I haven't a JIG but I will try to make one if I can find a 300K resistor
Can I find a 300K resistor into a old none working device ? (Like a old radio, tv, telecommand ?)
Phenom2 said:
Now my phone is unable to go in Download mode, recovery mode neither normal mode.
The screen stay black whatever I do, I've tried all the combinaison possible...
I tried to put it in charge all the night but now the problem is still here.
Any help appreciated
Click to expand...
Click to collapse
similar type of brick....and the suggestion given by the SSC is better to buy a new mobile since they have to replace the main board....(without warranty)..and cost will be around (Dhs.1150) that is almost half the price of new mobile....
btw i have tried jig also but no luck...
I have the same problem with my galaxy note.
i treid everything no reaction
pls has somebody an idea for me ?
Same problem with me.
Weird, I had a I91000 for a year, flashed everything and never had any problems. Never got close to bricking it.
I did this:
Rooted it with this method: http://forum.xda-developers.com/showthread.php?t=1501719 - OK
Ran again CWM.
I put the latest nightly from CM9. When I started flashing it, it hung. I turned off my cell (no other option, it was stuck), now it won't turn on.
Whoa... What did I do wrong? I admit I was anxious and didn't take the proper care I should've, I was very anxious, but, wow... I wasn't expecting it to be so easily brickable.
Do I have any hope left?
Hi everyone!
Here is the entire list of things I had done before I bricked it. Can some expert please read through and help me? I really need help!!
So as you can read from the title, this phone, the Galaxy Pop/Mini is bricked. It does not turn on at all, even if I press the power key only or the Power+home+vol.down. Needless to say, I have no download mode . The problem started after I flashed the PACman ROM, which didn't turn out that good, so I re-flashed the original firmware using ODIN. It said PASS, but then when it rebooted, the phone got a boot loop. It kept on rebooting again and again. As I have an Xperia Neo V as my primary device, this issue usually meant a wrong kernel to me. So I downloaded "Galpop_kernel_build2" and now when I press the power button or any of the combinations, the screen does not light up. There is no response.
So I tried the Heimdall One Click Unbrick, and it shows me this error:
Is Your Phone Plugged In?
Is It In Download/Softbrick Mode?
If the phone is Plugged In and Everything Is Fine,
Visit the Resolution Center in order to resolve the issue.
So I clicked on the button, it asked me to install 3 things, which I did, no luck. So I was finally going to give up, when I accidently pressed the volume up+ Power+ Home keys. Nothing happened on the screen, but when I connected it to my PC, Windows started installing some drivers! It went well, and even ODIN detected the phone (Yes, there was the Yellow Box), so I quickly tried to flash the original firmware, but it got stuck on "setup connection...". I read somewhere that this was a driver issue so I tried to uninstall and re-install the drivers, no luck.
So now, the phone does not turn on, but goes into this strange mode where it gets detected by ODIN, but cannot be flashed. I'm doomed! Can someone PLEASE HELP!!???
llsiddhantll said:
Hi everyone!
Here is the entire list of things I had done before I bricked it. Can some expert please read through and help me? I really need help!!
So as you can read from the title, this phone, the Galaxy Pop/Mini is bricked. It does not turn on at all, even if I press the power key only or the Power+home+vol.down. Needless to say, I have no download mode . The problem started after I flashed the PACman ROM, which didn't turn out that good, so I re-flashed the original firmware using ODIN. It said PASS, but then when it rebooted, the phone got a boot loop. It kept on rebooting again and again. As I have an Xperia Neo V as my primary device, this issue usually meant a wrong kernel to me. So I downloaded "Galpop_kernel_build2" and now when I press the power button or any of the combinations, the screen does not light up. There is no response.
So I tried the Heimdall One Click Unbrick, and it shows me this error:
Is Your Phone Plugged In?
Is It In Download/Softbrick Mode?
If the phone is Plugged In and Everything Is Fine,
Visit the Resolution Center in order to resolve the issue.
So I clicked on the button, it asked me to install 3 things, which I did, no luck. So I was finally going to give up, when I accidently pressed the volume up+ Power+ Home keys. Nothing happened on the screen, but when I connected it to my PC, Windows started installing some drivers! It went well, and even ODIN detected the phone (Yes, there was the Yellow Box), so I quickly tried to flash the original firmware, but it got stuck on "setup connection...". I read somewhere that this was a driver issue so I tried to uninstall and re-install the drivers, no luck.
So now, the phone does not turn on, but goes into this strange mode where it gets detected by ODIN, but cannot be flashed. I'm doomed! Can someone PLEASE HELP!!???
Click to expand...
Click to collapse
reinstall windows and try again. also try a different computer or laptop.
michal383 said:
reinstall windows and try again. also try a different computer or laptop.
Click to expand...
Click to collapse
I did, I am on a different PC right now, installed all drivers etc. But I just realized... I think I might have flashed the Pop Plus kernel...
Since it is ultimately the low level OS, maybe that is preventing it from starting? Is there a way to forcefully flash a different kernel? :'(
Also, the strange mode that it used to go into is gone now.. I cannot make the PC recognize the phone at all now, and the phone does not power up. So I'm kinda in a doomed position right now..:crying:
The mistake was the kernel flashing. If something is not booiting you need to wipe data/cache. This works with stock ROM too.
ast00 said:
The mistake was the kernel flashing. If something is not booiting you need to wipe data/cache. This works with stock ROM too.
Click to expand...
Click to collapse
I know, but the problem is, I cannot go into Download Mode or Recovery Mode. The battery is charged, but even after pressing the Power button or any of its combinations, the phone just doesn't turn on! No response what-so-ever.
Any suggestions?
Then no idea. I thought maybe you don't know where was the mistake so that's why I wrote it.
SSC. Simple right ?
F4uzan said:
SSC. Simple right ?
Click to expand...
Click to collapse
What is SSC? I have no idea about this.. Can you please explain what to do? :fingers-crossed:
llsiddhantll said:
Hi everyone!
Here is the entire list of things I had done before I bricked it. Can some expert please read through and help me? I really need help!!
So as you can read from the title, this phone, the Galaxy Pop/Mini is bricked. It does not turn on at all, even if I press the power key only or the Power+home+vol.down. Needless to say, I have no download mode . The problem started after I flashed the PACman ROM, which didn't turn out that good, so I re-flashed the original firmware using ODIN. It said PASS, but then when it rebooted, the phone got a boot loop. It kept on rebooting again and again. As I have an Xperia Neo V as my primary device, this issue usually meant a wrong kernel to me. So I downloaded "Galpop_kernel_build2" and now when I press the power button or any of the combinations, the screen does not light up. There is no response.
So I tried the Heimdall One Click Unbrick, and it shows me this error:
Is Your Phone Plugged In?
Is It In Download/Softbrick Mode?
If the phone is Plugged In and Everything Is Fine,
Visit the Resolution Center in order to resolve the issue.
So I clicked on the button, it asked me to install 3 things, which I did, no luck. So I was finally going to give up, when I accidently pressed the volume up+ Power+ Home keys. Nothing happened on the screen, but when I connected it to my PC, Windows started installing some drivers! It went well, and even ODIN detected the phone (Yes, there was the Yellow Box), so I quickly tried to flash the original firmware, but it got stuck on "setup connection...". I read somewhere that this was a driver issue so I tried to uninstall and re-install the drivers, no luck.
So now, the phone does not turn on, but goes into this strange mode where it gets detected by ODIN, but cannot be flashed. I'm doomed! Can someone PLEASE HELP!!???
Click to expand...
Click to collapse
It happens with me too when i flash diff kernel for overclocking and it's bricked i've tried almost every steps to unbrick even jig doesn't work anything so i given it to repair he said that reboot ic is gone he changed it and my phone back to use !
llsiddhantll said:
What is SSC? I have no idea about this.. Can you please explain what to do? :fingers-crossed:
Click to expand...
Click to collapse
Samsung Service Center
-------------------------------------
Your Mini life was in this place.
F4uzan said:
Samsung Service Center
-------------------------------------
Your Mini life was in this place.
Click to expand...
Click to collapse
Oh yes..I guess I'll have to go there.. BTW, what should I say? My phone is still in warranty, but I don't have the papers etc right no, since I'm in college.
I read somewhere that they will change your motherboard for free if in warranty, but how much would it cost? I was thinking of telling them that Kies did this
Zafar7777 said:
It happens with me too when i flash diff kernel for overclocking and it's bricked i've tried almost every steps to unbrick even jig doesn't work anything so i given it to repair he said that reboot ic is gone he changed it and my phone back to use !
Click to expand...
Click to collapse
As I asked someone else too, how much do you think it would cost if I don't have the warranty papers right now? It still is in warranty though..
And what did you tell them that convinced them that you were innocent?
I also had a problem where i had to get my motherboard changed when i asked the samsung people they said it'll cost Rs. 4000 for changing the motherboard so it'll be better if you find your warranty papers and don't worry just tell them that the phone's not working don't tell them about the rom flash stuff they'll repair it for free if you have your warranty papers..
Sent from my GT-S5570 using xda premium
arjunraina7 said:
I also had a problem where i had to get my motherboard changed when i asked the samsung people they said it'll cost Rs. 4000 for changing the motherboard so it'll be better if you find your warranty papers and don't worry just tell them that the phone's not working don't tell them about the rom flash stuff they'll repair it for free if you have your warranty papers..
Sent from my GT-S5570 using xda premium
Click to expand...
Click to collapse
That's the thing, I can't have the warranty papers because I am in college (far from home ), but I'll see what they do, I am going to the repair center today!
Yeah but its gonna cost you a lot of money.. :sly:
Sent from my GT-S5570 using xda premium
arjunraina7 said:
Yeah but its gonna cost you a lot of money.. :sly:
Sent from my GT-S5570 using xda premium
Click to expand...
Click to collapse
Yep, they asked me for 4,000.. That's almost half the price I bought the phone! I think I'm going to wait till December.. I'll be home then!
Thanks everyone for replying and helping!
llsiddhantll said:
Yep, they asked me for 4,000.. That's almost half the price I bought the phone! I think I'm going to wait till December.. I'll be home then!
Thanks everyone for replying and helping!
Click to expand...
Click to collapse
Yeah... I told ya you should get your warranty papers....:thumbup:
Sent from my GT-S5570 using xda premium
can u please explain???
Zafar7777 said:
It happens with me too when i flash diff kernel for overclocking and it's bricked i've tried almost every steps to unbrick even jig doesn't work anything so i given it to repair he said that reboot ic is gone he changed it and my phone back to use !
Click to expand...
Click to collapse
the same thing happened to me too..
the fun part is that this WAS my brother's phone(i mentioned WAS for the phone's been dead for a week )
can u please explain what did the SSC guy told you in detail???
unbricking mini/pop
try deleting all ur data on ur phone - ur android, data, etc....just factory reset it and then try flashing using odin!!!! if that also not works then use clockwork mod and restore backed up firmware on ur phone.
-_- he said he can't enter recovery or any other mode
Sent from my GT-S5570 using xda app-developers app
I was on cm10.1 build, and i clicked "restart" then it closed and now i think i am stuck in ramdump mode, i attached image.
Odin recongnises my phone but i am stuck at "SetupConnection", i am not in download mode and cannot get in it. i suppose it is "force upload " or something like this. please help me!
teodor79 said:
I was on cm10.1 build, and i clicked "restart" then it closed and now i think i am stuck in ramdump mode, i attached image.
Odin recongnises my phone but i am stuck at "SetupConnection", i am not in download mode and cannot get in it. i suppose it is "force upload " or something like this. please help me!
Click to expand...
Click to collapse
can you boot into system ! ?
stop posting these "brick! help!" threads. We cannot help you if you have a hard brick. CM10.1 ROM will not brick your device if you select "Reboot" Go to the service center.
Try removing the battery and then pressing the download mode button combination and Putting the battery in back while pressing the button combination
This is the emergency download mode
If it is not working
Try removing the battery and plug in the USB wire and press the button combination
Good luck
Sent from my GT-S6500 using xda premium
teodor79 said:
I was on cm10.1 build, and i clicked "restart" then it closed and now i think i am stuck in ramdump mode, i attached image.
Odin recongnises my phone but i am stuck at "SetupConnection", i am not in download mode and cannot get in it. i suppose it is "force upload " or something like this. please help me!
Click to expand...
Click to collapse
make a usb-jig to force it in download mode.
if nothing happens, go to service center.
my phone won't turn on anymore, even the screen. It is like i am starting it whit no battery. Does Jig work in this case? Also i forgot to mention that i tried expand ram with swapper 2
teodor79 said:
my phone won't turn on anymore, even the screen. It is like i am starting it whit no battery. Does Jig work in this case? Also i forgot to mention that i tried expand ram with swapper 2
Click to expand...
Click to collapse
that's why u got it bricked
don't use swapper with Oc kernel !
well, what could be the problem? is there any solution?
My phone was bricked aswell, I could not start it at all..not even with charger..it was simply dead...then i tried this
1.Pull out the battery, wait 15 minutes
2.With the battery out , press the power button for 30 seconds(make sure there are 30..i counted 32 to be sure )
3.Put the battery in and try to start it in download mode ( Vol- + Home +Power)
ok, i'll try it, i hope it will work, thank you in advance anyway
It didn't work, but i found on the internet a confidential samsung document with a procedure to flash from external sdcard, but i need JTAG, another mini 2 and the bootloader. so i really don't know what to do, may warranty is void, if i send to service, i think i must pay 100$ or more. i don't have this money.
I'll send it to service center, i think there is no way to revive it manually. I think there is nothing in the phone, because it doesn't boot or even turn on the screen. Anyone knows if EFS is corrupted, will they repair it, and if yes, how much will it costs?
teodor79 said:
I'll send it to service center, i think there is no way to revive it manually. I think there is nothing in the phone, because it doesn't boot or even turn on the screen. Anyone knows if EFS is corrupted, will they repair it, and if yes, how much will it costs?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=1604707
Try this before sending it to the service center. I sent mine and they brought it back saying it's unrepairable, but I don't believe them. I bricked my mini II with flashing wrong rom for other phone and I'm going to try this tomorrow because I can't find the resistors today.
hey man try this method:
1. Battery out. 4secs or more. Battery in (Remove SIM card and SD Card to be saved)
2. Volume DOWN + Home + Power Button. Hold it EXACTLY 5 SECONDS!
(NOW YOU IN DOWNLOAD MOD)
3. You will see or hear nothing! but remember you are there!
4. After when you got in download mod if you remember you need to "Press Volume UP" to confirm it. So press Volume UP and wait 2 seconds
5. Connect your mobile to the PC (Desktop ODIN Running). You will hear the sound. Which mean your phone connected.
6. Flash any stock firmware as you like....
Good Luck!
i don't have money for resistors, also method with download mode doesn't work. i don't think there is a solution
teodor79 said:
i don't have money for resistors, also method with download mode doesn't work. i don't think there is a solution
Click to expand...
Click to collapse
You don't have money for resistors? The price is really low, it costs 1€ in my country. I think USB jig will help or if you don't have time to build it, give it to Samsung service center, they will repair it for free
This thread is full of lulz!
Tomo123 said:
This thread is full of lulz!
Click to expand...
Click to collapse
I have bricked mine the same way, luckily I reset the bin counter before that, sent it to service and got it repaired for free. Motherboard replacement was necessary. So ALWAYS reset the bin counter after you flash!
i don't have money because i'm 13, and now i am at my grandparents. when i'' go home, i'll send it to service center
TheTrakO said:
I have bricked mine the same way, luckily I reset the bin counter before that, sent it to service and got it repaired for free. Motherboard replacement was necessary. So ALWAYS reset the bin counter after you flash!
Click to expand...
Click to collapse
They can't check your bin counter if you hard brick your device.
Sent from my GT-S6500 using xda app-developers app