[Q] Bricked Galaxy Note GT-N7000 using CWM - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Hey Guys. Greetings. I wanted to update my galaxy note [GT-N7000, India] to Android OMNIRom 4.4.2 Kitkat nightly build from Android 4.1.2 [Kernel version DDLSC]. Following steps led to bricking my phone:-
1. I first installed philz custom kernel [Version DDLSC CWM version 6.0.3.7] so that I could have CWM and SU.
2. Then I went to CWM Recovery mode, did factory reset. Then Wipe Cache. Then Wipe Dalvik Cache. Then I tried applying the omnirom update. It failed and gave me some context error and status 7.
3. Then I restored my 4.1.2 image using the CWM recovery only.
4. I booted into 4.1.2 and tried updating the CWM to 6.0.4.3 using ROM Manager. It succeded.
5. I went back again to recovery mode but it said again 6.0.3.7.
6. I tried applying update to CWM from CWM itself. It stuck at something like “replacing the stock recovery….”.
7. I powered off my phone. It went into boot loop once but somehow it started.
8. Then again I went into ROM manager and selected Boot into recovery mode.
9. It bricked my phone. Unable to boot since then. I cannot access recovery mode but I can access download/ODIN mode.
Here’s what I tried to do.
1. Downloaded CWM 6.0.4.3 touch .zip from clockworkmode.com
2. Renamed it to recovery.img.
3. Converted it to tar.md5 using img to tar tool.
4. Using Odin version 3.07, I tried flashing CWM.6.0.4.3.tar.md5 It stucks at NAND Write start.
Please help me recover my phone.
Specs: Samsung Galaxy NOTE GT-N7000
Original firmware: 4.1.2 kernelDLSC
16 GB internal usb storage
Country India.

chirags1986 said:
Bricked Galaxy Note GT-N7000 using CWM
Click to expand...
Click to collapse
Few things you should have already read and understood.
1. Note N7000 doesn't have a separate active recovery partitions as the S3 and so on.. The recovery is built in to the kernel. So flashing Philz was a correct step.
2. You cannot update the recovery using ROM manager as it writes to the recovery partition which this phone doesn't use. Thus you didn't get the updated recovery.
3. Using odin will not work due to 1&2
Download the Philz kernel DDLC tar version and flash using Odin (uncheck Auto reboot). Once it shows Pass, then power off the phone and remove the usb cable. Boot into recovery using the vol up+home+power. The flash a kernel like Raw r4/r5. reboot into recovery and wipe. Flash Omni, Gapps, SU. Reboot.
Revive your phone by flashing stock firmware using.
So its not really "Bricked Galaxy Note GT-N7000 using CWM" but bricked due to sheer ignorance.

my device bricked
nokiamodeln91 said:
Few things you should have already read and understood.
1. Note N7000 doesn't have a separate active recovery partitions as the S3 and so on.. The recovery is built in to the kernel. So flashing Philz was a correct step.
2. You cannot update the recovery using ROM manager as it writes to the recovery partition which this phone doesn't use. Thus you didn't get the updated recovery.
3. Using odin will not work due to 1&2
Download the Philz kernel DDLC tar version and flash using Odin (uncheck Auto reboot). Once it shows Pass, then power off the phone and remove the usb cable. Boot into recovery using the vol up+home+power. The flash a kernel like Raw r4/r5. reboot into recovery and wipe. Flash Omni, Gapps, SU. Reboot.
Revive your phone by flashing stock firmware using.
So its not really "Bricked Galaxy Note GT-N7000 using CWM" but bricked due to sheer ignorance.
Click to expand...
Click to collapse
i flash philz kernel
then i wanted to flash cm11 so
i wiped data
wiped cache
wiped system
wiped dalvik
then i selected cm11 and it showed error status7
so i restored my backup rom
now i restarted my device and it says system ui has stopped..

amiransari2 said:
i flash philz kernel
then i wanted to flash cm11 so
i wiped data
wiped cache
wiped system
wiped dalvik
then i selected cm11 and it showed error status7
so i restored my backup rom
now i restarted my device and it says system ui has stopped..
Click to expand...
Click to collapse
nokiamodeln91 said:
Download the Philz kernel DDLC tar version and flash using Odin (uncheck Auto reboot). Once it shows Pass, then power off the phone and remove the usb cable. Boot into recovery using the vol up+home+power. The flash a kernel like Raw r4/r5. reboot into recovery and wipe. Flash Omni, Gapps, SU. Reboot.
Click to expand...
Click to collapse
Again you did not read properly.

bricked galaxy note gt n7000 using cwm
nokiamodeln91 said:
Again you did not read properly.
Click to expand...
Click to collapse
srry but i have flashed stock rom using odin now my prob is solved.......but why that prob incurred

Hello Sir,
I have the same problem as that guy above. I am unable to boot into download mode itself. How can I connect to odin? Please help sir.
nokiamodeln91 said:
Few things you should have already read and understood.
1. Note N7000 doesn't have a separate active recovery partitions as the S3 and so on.. The recovery is built in to the kernel. So flashing Philz was a correct step.
2. You cannot update the recovery using ROM manager as it writes to the recovery partition which this phone doesn't use. Thus you didn't get the updated recovery.
3. Using odin will not work due to 1&2
Download the Philz kernel DDLC tar version and flash using Odin (uncheck Auto reboot). Once it shows Pass, then power off the phone and remove the usb cable. Boot into recovery using the vol up+home+power. The flash a kernel like Raw r4/r5. reboot into recovery and wipe. Flash Omni, Gapps, SU. Reboot.
Revive your phone by flashing stock firmware using.
So its not really "Bricked Galaxy Note GT-N7000 using CWM" but bricked due to sheer ignorance.
Click to expand...
Click to collapse

techblazes said:
Hello Sir,
I have the same problem as that guy above. I am unable to boot into download mode itself. How can I connect to odin? Please help sir.
Click to expand...
Click to collapse
So no download and recovery mode? Is your battery charged?

nokiamodeln91 said:
So no download and recovery mode? Is your battery charged?
Click to expand...
Click to collapse
I got the download mode after removing and replacing the battery sir. But ODIN is not showing Added message when I connect my device...

techblazes said:
I got the download mode after removing and replacing the battery sir. But ODIN is not showing Added message when I connect my device...
Click to expand...
Click to collapse
Try different USB port, cables, and check if the drivers are installed properly.. Samsung USB drivers..

Looks like the drivers are working back after using Kies. Now I connected the device and ODIN is doing its task. Will update if it successfully finishes the job.
Thanks
Edit: Everything is working as expected. ODIN has flashed CWM on my device and now I am restoring my device using the backup I created yesterday...

Got into the same problem as the OP. Wiped everyting and only have Phliz recovery. Couldn't flash CM11 because according to CM thread must have latest version of CWM (6.0.3.4) while the philz recovery I installed is based on 6.0.2.7. Couldn't flash newer recovery I downloaded from CWM site, it would just freeze and get stuck.
My solution is to just flash CM10.1.3 stable plus gapps. Worked fine. Then proceed from there.

You must have CWM 6.0.4.4 or higher, which is fully SELinux compatible for KitKat.
Just flash Raw kernel r4, reboot in recovery (of raw kernel ) and then do your flash and wipes.
You can't simply install a newer recovery on our device, as kernel and recovery are bound together, but ...THIS IS BASIC KNOWLEDGE FOR OUR DEVICE!!!
#fail²

Just resurrecting this!
After failing to flash KitKat because I had Philz kernel installed, I've got into a real mess.
I'm trying to flash raw kernel r5 but recovery isn't able to mount the SD card and so can't see the zip files on it.
I'm on a Mac and don't have Bootcamp so can't use Odin. Any suggestions?

Oops didnt realise this was kinda necroed :/

Same problem...i have brisked my N7000
i want to know where you have got stock ROM 4.1.2....please help me sir. regards,

manojleo79 said:
i want to know where you have got stock ROM 4.1.2....please help me sir. regards,
Click to expand...
Click to collapse
Go find what you want Here

chirags1986 said:
Here’s what I tried to do.
1. Downloaded CWM 6.0.4.3 touch .zip from clockworkmode.com
2. Renamed it to recovery.img.
3. Converted it to tar.md5 using img to tar tool.
4. Using Odin version 3.07, I tried flashing CWM.6.0.4.3.tar.md5 It stucks at NAND Write start.
Please help me recover my phone.
Specs: Samsung Galaxy NOTE GT-N7000
Original firmware: 4.1.2 kernelDLSC
16 GB internal usb storage
Country India.
Click to expand...
Click to collapse
No need to do all this ^
Flash this using ODIN. Pick the tar file

techblazes said:
Looks like the drivers are working back after using Kies. Now I connected the device and ODIN is doing its task. Will update if it successfully finishes the job.
Thanks
Edit: Everything is working as expected. ODIN has flashed CWM on my device and now I am restoring my device using the backup I created yesterday...
Click to expand...
Click to collapse
Hi all,
I too have the same problem, tried following as instructed
- Download the Philz kernel DDLC tar version (PhilZ-cwm6-DDLSC-ODD-5.11.2.tar)
- flashed using Odin by unchecking Auto reboot option
- Once it showed Pass( it also showed RESTE then went on to became green), then power off the phone and removed the usb cable.
- Tried to boot into recovery by using the vol up+home+power
unfortunately got stuck in the initial screen with yellow triangle
Kindly help
---------- Post added at 04:22 AM ---------- Previous post was at 04:07 AM ----------
techblazes said:
Looks like the drivers are working back after using Kies. Now I connected the device and ODIN is doing its task. Will update if it successfully finishes the job.
Thanks
Edit: Everything is working as expected. ODIN has flashed CWM on my device and now I am restoring my device using the backup I created yesterday...
Click to expand...
Click to collapse
Hi all,
I am new to XDA, and has been following XDA for ROM upgradation on my GTN7000 Samsung note
But today I have landed in the problem when I tried to upgrade the CWM through ROM manager. May be because of half knowledge.
After searching on the XDA I came across above thread identical to the issue I am facing wit same note config, with a great relief I tried to replicate the same for my N7000
steps followed.
- Download the Philz kernel DDLC tar version (PhilZ-cwm6-DDLSC-ODD-5.11.2.tar)
- flashed using Odin by unchecking Auto reboot option
- Once it showed Pass( it also showed RESTE then went on to became green), then power off the phone and removed the usb cable.
- Tried to boot into recovery by using the vol up+home+power
unfortunately got stuck in the initial screen with yellow triangle
Kindly help.

Hi Experts,
please help. I am still stuck with yellow triangle and samsung logo.
Regards

n7000g said:
Hi Experts,
please help. I am still stuck with yellow triangle and samsung logo.
Regards
Click to expand...
Click to collapse
Try downloading XXLTA stock firmware. Flash it with odin, after finished reboot to stock recovery n do a factory wipe reset, reboot. After that download phils XXLTA kernel and flash it in stock recovery. It will give u root n phils recovery. After that u can do whatever u want with ur phone
Sent from my GT-N7000 using XDA Free mobile app

Related

Custom ROM question.

I currently have a rooted SGH-T879. I have never installed a custom ROM before but I would like to install CM10.
The problems I am having are
- CMW and TWRP only have i717 (would this work)?
- I cannot boot into recovery mode. (When I do the button combo it's a black screen after the samsung logo and when I use an app to boot into recovery it soft bricks the phone.
- I am getting a installation aborted error when I tried to install it before the recovery mode stopped working.
The files I have are:
[email protected] (file name exactly as typed)
gapps-jb-20130301-signed.zip (file name exactly as typed)
I also have USB debugging and Unknown sources checked.
Please help, this is far more complicated than the jailbreak on ios that I was used to. Thanks
Do yoi have a custom recovery installed? If so, which one? Did you root the phone via odin?
Sent from my SAMSUNG-SGH-I717 using xda premium
androidmechanic said:
Do yoi have a custom recovery installed? If so, which one? Did you root the phone via odin?
Currently I do not have a custom recovery, I had CWM 5.0 previously but I am trying to install CWM 5.8.4.3 or TWRP 2.3.1.1 which I think are latest for my Note. Those are coming to no avail also.
CWM - the progress bar isn't moving when using the .tar file (used odin 1.85 and 3.04 and 3.07)
TWRP - odin crashes after using the .img.tar.md5 file after it verifies files.
Click to expand...
Click to collapse
Maybe need to uninstall odin then reinstall the latest version and reroot. May have a corrupted odin download
Sent from my SAMSUNG-SGH-I717 using xda premium
Three fresh downloads, still have the same results.

[Q] Help restoring my rooted Galaxy Note n7000 to stock status.

Hi there,
I have a rooted Galaxy Note N7000 running JellyBean 4.1.2. and I've got a ton of apps/photos/videos/messages... etc.
and I've sensed the phone is getting slow. I've removed all the unnecessary apps and deleted photos/videos etc..
but its still slow.
so anyway I decided to start from scratch, I decided to unroot the phone and install a stock rom. delete all photos/videos/apps.. everything.
so I downloaded the official latest stock rom released from samsung for my region. (N7000JPLSB_N7000OJPLSB_XSG)
and I've looked at many many pages on the internet and some site different methods than other, which got confusing.
finally i decided i'd go with the method mentioned in this page:
rootgalaxynote(dot)com/galaxy-note-unroot/how-to-unroot-galaxy-note-gt-n7000/
(sorry for the link formatting it wouldn't let me post a url)
the problem is, at the end of the page it says to do a “Wipe data/factory reset”. However, I have read on many sites and threads that you should never do a factory reset on stock Rom!
So now i'm confused.
1- is the method mentioned in the page i linked above correct and safe?
2- will the method above delete everything? ie: photos/videos/apps.. etc (which is what i want) if not, how do i achieve that?
3- do i do a Wipe data/factory reset? or not?
Thanks in advance.
What's your current config?
nokiamodeln91 said:
What's your current config?
Click to expand...
Click to collapse
sorry i don't understand. i'm really new to this. What do you mean by current config?
What rom are you running and what kernel. Rooted.
1.Download a stock rom for n700
2.Install odin on your pc
3.Go to download mode by pressing the vol + , power button + center button
4.press vol +
You are in odin flash mode for ur mobile.
Open odin on ur pc
Check if ur phone is detected. If the upper box is yellow and it shows a COM usb port.
Browse the stock rom file a .tar.md5 file in the PDA section let everything as it is.
Press flash and wait and note things happen.
The yellow box will turn green with PASS written on it.
Reboot ur phone.
A simple how to
Sent from my GT-N7000 using xda app-developers app
Right. Here my info:
Baseband Vesion: N7000XXLSO
Kernel Version: 3.0.31-906407 / [email protected] #3 / SMP PREEMPT Tue Feb 19 22:05:07 KST 2013
Build Number: JZO54K.N7000JPLSB
Flash Philz kernel and boot into cwm recovery. The go to mounts and storage and format system, data, cache and preload. This will completely erase the trace of old system. Then go back to advanced menu and choose reboot download. Then flash the rom as per reply by above member.
Before doing this just make sure you have a working usb connection because after the steps there won't the any rom on phone to boot till you flash the new now.
nokiamodeln91 said:
Flash Philz kernel and boot into cwm recovery. The go to mounts and storage and format system, data, cache and preload. This will completely erase the trace of old system. Then go back to advanced menu and choose reboot download. Then flash the rom as per reply by above member.
Before doing this just make sure you have a working usb connection because after the steps there won't the any rom on phone to boot till you flash the new now.
Click to expand...
Click to collapse
HI, thanks for your reply, i found Philz Kernel, but what is cwm recovery? and how do i boot into it?
To boot in CWM, you shut down your Note. And then you press Vol-, Home and Power for recovery Mode.
bakkouz said:
HI, thanks for your reply, i found Philz Kernel, but what is cwm recovery? and how do i boot into it?
Click to expand...
Click to collapse
Recovery mode is a mode in which you have control on Android file systems, internal and external SD cards. It run without Android.
Thanks, about the Kernel though.. as I said I found the page regarding Philz kernel, but there are so many of them i really don't know which one to download. there are so many threads intertwined it get really confusing.
is it the one in here:
http://forum.xda-developers.com/showpost.php?p=31911682&postcount=3
should i download the JPLSB one? will this root my phone (again?) cause i don't want it rooted.
should i even download the kernel? i mean do i really need to? is it because my current kernel will cause problems?
bakkouz said:
HI, thanks for your reply, i found Philz Kernel, but what is cwm recovery? and how do i boot into it?
Click to expand...
Click to collapse
1 - Flash Philz kernel
2 - Go to Recovery Mode
3 - Go on "Mount & Storage"
3 - Format ALL ! (Data, Cache, System, Emmc etc ...) Save whant you want to save before.
4 - Go in Advanced, Format Dalv. cache.
5 - Shut down your phone (remove your battery)
6 - Turn on your note in Odin Mode (Vol+, Home & Power)
7 - Flash your last Touchwizz stock rom with Odin.
I'm French, I've do this manip, I'm on XXLT4 full stock. Fast & Economic. (2,5 days)
KalamiGeek said:
1 - Flash Philz kernel
Click to expand...
Click to collapse
Ok. great. but:
1- i have no idea how to flash a kernel.
2- which kernel to chose?
- PhilZ-cwm6-JPLSB-UAE-5.00.5.tar.md5
or
- PhilZ-cwm6-JPLSB-UAE-5.00.5-signed.zip
cause in the thread it says the zip will root the phone, and i don't want to root the phone, can i flash using the tar.md5 one?
bakkouz said:
Ok. great. but:
1- i have no idea how to flash a kernel.
2- which kernel to chose?
- PhilZ-cwm6-JPLSB-UAE-5.00.5.tar.md5
or
- PhilZ-cwm6-JPLSB-UAE-5.00.5-signed.zip
cause in the thread it says the zip will root the phone, and i don't want to root the phone, can i flash using the tar.md5 one?
Click to expand...
Click to collapse
Check .tar.md5
Find Odin v3.04. Put philz kernel .tar.md5 on Pda case. And flash it
bakkouz said:
Ok. great. but:
1- i have no idea how to flash a kernel.
2- which kernel to chose?
- PhilZ-cwm6-JPLSB-UAE-5.00.5.tar.md5
or
- PhilZ-cwm6-JPLSB-UAE-5.00.5-signed.zip
cause in the thread it says the zip will root the phone, and i don't want to root the phone, can i flash using the tar.md5 one?
Click to expand...
Click to collapse
Yes, use tar.md5 file with Odin PC as previously shown.
That file is Philz kernel and add ROOT by default. To avoid root add, use philz_installer.cfg as indicated in the Philz thread.
Ok great, thank you for all the help.
i just hope i don't brick the phone
HI just one last fast question please...
as for philz_installer.cfg it says to put it in /sdcard/clockworkmod/philz_installer.cfg
but i don't have a clockworkmod folder.
should i create it? or put on directly on /sdcard main folder?
Don't use the tar file. It will cause a yellow triangle. Use the zip version. Place it on external sd card. Don't worry about cfg file for now. Boot into recovery and choose apply update from external storage. Choose the zip and flash. After it completes, click on reboot system. The again boot into recovery and you should see cwm
nokiamodeln91 said:
Don't use the tar file. It will cause a yellow triangle. Use the zip version. Place it on external sd card. Don't worry about cfg file for now. Boot into recovery and choose apply update from external storage. Choose the zip and flash. After it completes, click on reboot system. The again boot into recovery and you should see cwm
Click to expand...
Click to collapse
I've often used Odin PC to flash new ROM's, for example Stock LT4 and Stock LT5, no problem, no yellow triangle. To avoid it in the future, please explain when and why we get the trouble triangle yellow. Thanks.:good:
you will get a yellow triangle if you flash anything else that stock roms using PC odin. you will also get an increased counter. nothing to worry if you are out of warranty though

HELP!! Phone bricked!

EDIT: problem solved
teodor79 said:
hi everyone, i installed thewhisp cyanogenmod 10.1 , then I decided to revert to stock. after i flashed the stock firmware, I tried to boot into recovery to wipe data (if i don't do this i get into bootloop) but when i pressed all buttons, it won't boot in recovery
now i am stuck in bootloop and can't recover it, please help me!
Click to expand...
Click to collapse
Does the phone boot to the galaxy mini 2 screen? If it boots then its not hard bricked
Put the phone in ODIN mode and reflash again the stock firmware. If it still does not boot and you cant get into recovery, flash again the firmware but this time check re partition. You will need the jena or jenad pit. NOTE: THIS WILL WIPE ALL YOUR DATA!!!!!
only wipe data/factory reset & install stock again
No no always when you want to back to the stock ROM you must flash cwm and wipe data/factory and wipe cache and wipe dalvik cache and go to the mounts and storage and wipe everything then go downlaod mode and flash stock then trust me it will be ok
Sent from my GT-S6500 using xda app-developers app
this is probably Samsung bootloader bug, I don't know what's causing that, but you must wipe data before you flash back to stock via Odin
Porobu said:
Does the phone boot to the galaxy mini 2 screen? If it boots then its not hard bricked
Put the phone in ODIN mode and reflash again the stock firmware. If it still does not boot and you cant get into recovery, flash again the firmware but this time check re partition. You will need the jena or jenad pit. NOTE: THIS WILL WIPE ALL YOUR DATA!!!!!
Click to expand...
Click to collapse
i tried to repartition (i also have jena NON-nfc pit), the same result, it boots only in download mode, or android (i got bootloop and vibrate something like beep.........beep beep beep)
TheWhisp said:
this is probably Samsung bootloader bug, I don't know what's causing that, but you must wipe data before you flash back to stock via Odin
Click to expand...
Click to collapse
yeah, it may be
btw, is there anyway to recover? (without samsung center)
I've had the same problem, sometimes it just boots into recovery
TheWhisp said:
I've had the same problem, sometimes it just boots into recovery
Click to expand...
Click to collapse
my last idea is: after flashing stock firmware, it boots into recovery, then into system. It is possible to replace the original "recovery.img" with cwm "recovery.img" in the original system package?
teodor79 said:
i tried to repartition (i also have jena NON-nfc pit), the same result, it boots only in download mode, or android (i got bootloop and vibrate something like beep.........beep beep beep)
yeah, it may be
btw, is there anyway to recover? (without samsung center)
Click to expand...
Click to collapse
Try:
Install stock rom with odin
After installing install CWM or TWRP with odin
When the rom boots connect ur phone to pc and in adb do: adb reboot recovery
Sent from my GT-S6500D using xda app-developers app
Try this: http://forum.xda-developers.com/showthread.php?t=2227982
TheWhisp said:
Try this: http://forum.xda-developers.com/showthread.php?t=2227982
Click to expand...
Click to collapse
thanks alot! it worked! you're a life saver!
Had the same problem, connected the phone to the charger and then I was able to enter CWM Recovery, I wiped data and it worked.

Help?

Right, to cut a lonnnnng first post story short, basically, rooted my phone yesterday, went well, installed some rooted apps and was having fun, one app, 3D something, from Google Play. it asked me to restart my phone after setting superuser (i thought this was quite weird) anyway i boot locked my phone - got the typical "Samsung GALAXY Note GT-N7000" and the phone woundnt move from there, i can gt into vol+ home and power and vol- home and power still. so after some research i found i had to flash therelivant stock ROM using odin - so i did. and it worked. then at somepoint today my phone got stuck in a boot loop consisting of the GT-N7000 screen then the samsung spash screen. when i do vol+ home power, i get in red text "E:/error%20in%20/data/recovery_last_kernal_log.txt" - what does this mean? and how(if at all) do i fix it?
i have curently re-flashed stock ROM and vol+ home power & "wipedata/factory reset" and so far so good......
any help or shed light would be a great help
Phone is Samsung GALAXY Note GT-N7000
Flashing the stock rom won't change anything if you have not wiped data. It just restores the system. What rom are you on? JB or ICS? To get everything to factory standards, install philz kernel.
Then boot into Cwm and choose wipe data,-clean before new rom flash.
Once it's done, choose reboot download and flash the rom again with odin. This way anything that the "3d something" might have done will go.
Sent from my GT-I9500 using xda premium
nokiamodeln91 said:
Flashing the stock rom won't change anything if you have not wiped data. It just restores the system. What rom are you on? JB or ICS? To get everything to factory standards, install philz kernel.
Then boot into Cwm and choose wipe data,-clean before new rom flash.
Once it's done, choose reboot download and flash the rom again with odin. This way anything that the "3d something" might have done will go.
Sent from my GT-I9500 using xda premium
Click to expand...
Click to collapse
it was called "Chainfire3d" and could you write the bove in steps?
i currently have flashed stock JB rom... and its working for now, but i dont want to turn it off incase it loops again. so what should i do from here, its currently un-rooted...
thanks a million for your reply
1. Install philz kernel from recovery.
2. Boot into Cwm recovery and choose clean before new rom install.
3. Choose reboot download.
4. Connect to pc and flash rom using odin.
Sent from my GT-I9500 using xda premium
nokiamodeln91 said:
1. Install philz kernel from recovery.
2. Boot into Cwm recovery and choose clean before new rom install.
3. Choose reboot download.
4. Connect to pc and flash rom using odin.
Sent from my GT-I9500 using xda premium
Click to expand...
Click to collapse
so put philz kernel on the ext sdcard
vol+ home power - and install
boot into cwm and choose clean before new rom install
reboot into download
and then flash stock rom?
one last question... will the lastest philz kernel work?
thanks again
i currently have PhilZ-cwm6-XXLT4-OXA-4.93.6-signed on my external sd.... will this do?
yeah any kernel will do as you just need recovery... once the kernel is installed, boot into recovery.. You should see CWM based recovery.
nokiamodeln91 said:
yeah any kernel will do as you just need recovery... once the kernel is installed, boot into recovery.. You should see CWM based recovery.
Click to expand...
Click to collapse
and then clean before new rom install?
xDEADFAMOUSx said:
and then clean before new rom install?
Click to expand...
Click to collapse
yes if you got the philz recovery installed.

[Q] How to UnBrick galaxy n7000

Hi,
other day I was playing game on my note 1 and then battery ran out and now my phone wont boot up and it is stuck at animated samsung logo.
It was running on stock rom and it was never rooted.
Now when i go in recovery mode it gives this error:
failed to mount /efs
I tried installing the stock rom but with no luck.
I am newbie into this all, so can you please guide how to fix this ..
Regards
ahmedmasu said:
Hi,
other day I was playing game on my note 1 and then battery ran out and now my phone wont boot up and it is stuck at animated samsung logo.
It was running on stock rom and it was never rooted.
Now when i go in recovery mode it gives this error:
failed to mount /efs
I tried installing the stock rom but with no luck.
I am newbie into this all, so can you please guide how to fix this ..
Regards
Click to expand...
Click to collapse
You should try to put your Note in download mode and flash a stock rom with Odin.
You must flash the PIT file to repartition your phone's storage, chose the right one (16 or 32 Gb).
I am almost sure that your phone is soft bricked and it is recoverable.
If it don't work, thant mean that your have bad blocks in your phone's storage. Have you wiped your note while under ICS android ?
what rom were you on? if JB, try a factory reset.
nokiamodeln91 said:
what rom were you on? if JB, try a factory reset.
Click to expand...
Click to collapse
I was on latest stock rom which is ICS.
Btw I tried to reset it to factory but with no luck
lionelia said:
You should try to put your Note in download mode and flash a stock rom with Odin.
You must flash the PIT file to repartition your phone's storage, chose the right one (16 or 32 Gb).
I am almost sure that your phone is soft bricked and it is recoverable.
If it don't work, thant mean that your have bad blocks in your phone's storage. Have you wiped your note while under ICS android ?
Click to expand...
Click to collapse
Thank for your reply.
I tried flashing the stock rom with Odin but the error remained there
Can you please give me a link from where I can get PIT file?
ahmedmasu said:
I was on latest stock rom which is ICS.
Btw I tried to reset it to factory but with no luck
Click to expand...
Click to collapse
You shouldn't be doing a reset on ICS stock at all.. Install Philz kernel for ICS and wipe data and cache.. When flashing a stock rom using odin, is it a success?
nokiamodeln91 said:
You shouldn't be doing a reset on ICS stock at all.. Install Philz kernel for ICS and wipe data and cache.. When flashing a stock rom using odin, is it a success?
Click to expand...
Click to collapse
Is there any guide\link to do this ?
http://forum.xda-developers.com/showthread.php?t=1901191
nokiamodeln91 said:
You shouldn't be doing a reset on ICS stock at all.. Install Philz kernel for ICS and wipe data and cache.. When flashing a stock rom using odin, is it a success?
Click to expand...
Click to collapse
I have successfully flashed rom on my phone which is : N7000ZSLPF_N7000OZSLPF_OZS
My phone is now out of bootloop but now I face a different issue that I cant get my sim card work, it gives no signal and I noticed one more thing that IMEI of my phone is blank.
I went into recovery mode and it is still showing that efs error as it was showing before...
Any suggestion what should I try to fix this ?
So you never installed any rom or a custom kernel?
---------- Post added at 03:15 AM ---------- Previous post was at 03:11 AM ----------
Look for a file on your storage named efs.autobackup.img. If nothing like that, check on this site http://www.cvxcvx.pl/en/podstrona-0/naprawa-efs-w-i9100-n7000/ for some instructions. Read carefully and proceed.
nokiamodeln91 said:
So you never installed any rom or a custom kernel?
---------- Post added at 03:15 AM ---------- Previous post was at 03:11 AM ----------
Look for a file on your storage named efs.autobackup.img. If nothing like that, check on this site http://www.cvxcvx.pl/en/podstrona-0/naprawa-efs-w-i9100-n7000/ for some instructions. Read carefully and proceed.
Click to expand...
Click to collapse
I followed the instructions provided by the manual ... after step 2 I get imei but after step 3 it get empty again.
Signals do come after step 2 but when I try to make some call it says "Not registered on network".
Looking forward to your reply.
i cannot help you in this case if there is no efs backup.. so.. you on your own..
nokiamodeln91 said:
i cannot help you in this case if there is no efs backup.. so.. you on your own..
Click to expand...
Click to collapse
Thanks for your help so far...
I currently have an imei but it is some random number starting with "004999" and I do get signals but cant make a call .. Do you know if there is some hope for me or not .. and what else I can try.
This is the developer imei. You may be able to make calls of you try a GB rom. Or there is one rom by ThaiDai which had some work around built into it. I don't know which one.
Else the site I mentioned earlier has contact info of cvxcvx. He can fix your phone remotely but by charging about 10 euros.
Need help for a bricked N7000
Hi guys,Im a complete newbie to the whole custom rom scenario. Yet, after being fed up of touchwiz on my N7000 i decided i wanted to taste some KitKat on my phone. After seeing many videos with positive reviews I thought it would be a rather easy process. But somehow I seem to have made a mistake and now my phone is stuck on Samsung Galaxy Note N7000 logo. I cant get into recovery mode as suggested on most places. As of now I only have access to the download mode but dont know what to do with it.
Here's what I tried doing :
1) I was on stock OS, and these are my specifics : Galaxy Note N-7000 running JB 4.1.2
Baseband version : N7000DDLS6
Kernel version: 3.3.31-906407
BUild number:JZO54K.N7000DDLSC
2) As I was following the procedure from Omnirom's official website, I first rooted my phone using Framaroot's single click root app. This gave me SuperSU app.
3) Then I tried installing TWRP recovery (recommended by Omni) but they dont support the N7000. I read a few other tutorials where it was stated the CWM recovery and that too Philz CWM recovery is the best to go with. Apparently it is just stock kernel with CWM recovery. Since the latest one(philz_touch_6.07.9-n7000) was not being installed, I installed the one before that which worked (PhilZ-cwm6-DDLSC-ODD-5.11.2-signed).
4) I even installed the ROM Manager as per the tutorial. However, uptil now I could access recovery mode ( Vol UP+Home+Power) and i saw the touch enabled philz recovery mode once. Then i did system reboot.
5)After reboot, this is where I did a mistake in my opinion. I opened ROM Manger and clicked on "open in recovery mode" option. Since then the phone is stuck on the Galaxy Note N7000 logo. Please help me revive the phone. Thanks in advance. Again, Im doing this for the first time and most terms are new to me. So please explain the procedure as other tutorials are not very clear.
You missed on reading the most important instructions.
Rom manager will not work with note. Recovery is built into the kernel on note and not as a separate partition.
Try harder to get into recovery mode. If you still can't, get the ddlsc Philz kernel tar version. Flash it using Odin. Then power off the device and boot into recovery. Then flash raw kernel. Reboot recovery. Flash omni and other required zips.
nokiamodeln91 said:
You missed on reading the most important instructions.
Rom manager will not work with note. Recovery is built into the kernel on note and not as a separate partition.
Try harder to get into recovery mode. If you still can't, get the ddlsc Philz kernel tar version. Flash it using Odin. Then power off the device and boot into recovery. Then flash raw kernel. Reboot recovery. Flash omni and other required zips.
Click to expand...
Click to collapse
How do I do i install the kernel using ODIN? I can only access download mode and nothing else. I cant access recovery mode. Please help.
PhilZ kernel has two versions, zip and tar. Use the tar version to flash via odin.
Sent from my GT-N7000 using Tapatalk 2
forest1971 said:
PhilZ kernel has two versions, zip and tar. Use the tar version to flash via odin.
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
Bro can i ask for the link of philz kernel and raw kernel. I'm new here. Thanks in advance.
ANDROID-000 said:
Bro can i ask for the link of philz kernel and raw kernel. I'm new here. Thanks in advance.
Click to expand...
Click to collapse
http://www.mediafire.com/?ep82ku4c6...o6dtlx8lbc3xz,ob3q9g36b9b3w22,d3v1gys7cbckiet

Categories

Resources