Database Develop

[Q] Xperia T - won't go past sony start sreen

Hi all, I'm new here and very much a novice when it comes to phones, operating systems etc so excuse me for the noob question and complete lack of knowledge...
My Xperia T developed a microphone fault whereby nobody could hear me when I called them (incredibly faint). I had the phone repaired at a local repair shop. Almost immediately upon receiving the phone back it developed a (What appears to be very common) battery fault, whereby it would reach 80% then shut down, restart, shut down, restart......
So, before returning it to the shop for further repairs I attempted a repair using the sony software. Half way through this repair the phone shut down!!! PC lost communication and I was left with a phone that simply displayed the 'Sony' start-up logo.
I have now returned to the shop and they have installed a new battery but are unable to get communication with the phone via the sony software (so basically they dont appear to be getting any further than me!). They are saying it is beyond repair - but I find that hard to believe? Surely it is just a software issue?
Can anyone advise what can be done? I am reluctant to write this phone off - surely it can be flashed with a new operating system or whatever needs to be done to what is essentially now a 'dumb' device?

This is the way to fix the software issue, ALL YOU DATA WILL BE LOST. And i'm not responsible for anything might happen to you device . DO THIS AT YOUR OWN RISK.
Google xperia t .145 ftf file
Google flashtool for xperia
Download them
When you have installed flashtool, go to its folder, install drivers (tick the TX, flashmode and fastboot drivers boxs)
Open flashtool, click the lightning logo, select flashmode
Put the firmware file you've downloaded to the firmware folder in flashtool folder.
Connect the phone in flashmode, hold power and volume up until it vibrates 3 times, now hold the vol down, plug your phone in the computer with flashtool running, you will now able to flash the firmware.
Good luck man.

tuzmaster_v2 said:
This is the way to fix the software issue, ALL YOU DATA WILL BE LOST. And i'm not responsible for anything might happen to you device . DO THIS AT YOUR OWN RISK.
Google xperia t .145 ftf file
Google flashtool for xperia
Download them
When you have installed flashtool, go to its folder, install drivers (tick the TX, flashmode and fastboot drivers boxs)
Open flashtool, click the lightning logo, select flashmode
Put the firmware file you've downloaded to the firmware folder in flashtool folder.
Connect the phone in flashmode, hold power and volume up until it vibrates 3 times, now hold the vol down, plug your phone in the computer with flashtool running, you will now able to flash the firmware.
Good luck man.
Click to expand...
Click to collapse
Thankyou very much for your reply!! Thats what I need, a step by step muppets guide!
To be honest I couldn't care less about any data, I'm way past that stage - if I can just have the phone working again I would be a very happy man (I'm fairly desperate as you can probably tell, Im running my business from an ancient, failing HTC desire following weeks of the shop having the sony!). I can't really afford to write off a phone I paid good money for 6 months back so need to have a go myself.
I am collecting the phone today so will give that a go.....

So I had a go at the above - got the flash tool installed (Emma?) etc and managed to get the software to see the phone - unfortunately though I had neglected to mention the phone is locked to a particular network, which Emma politely informs me.
So, I have attempted to follow unlocking instructions as per the sony instructions (on their website):
But I am stuck. I was getting nothing when using the volume down button and connecting. To get the computer to see the phone I have to press and hold the power button, the red led starts blinking 3 times, repeatedly. This causes windows to recognise the phone when plugged in via usb, but I was not being asked for drivers (as per sony step 13). I found the device in device manager and uninstalled drivers in an attempt to force this. Now all that happens is the device appears in the list as 'S1 Boot Load' with a yellow exclamation mark. However I have then tried installing drivers manually from the location where I copied 'android_winusb' to, but this does not work.
To compound the issue I think the battery problem is causing the phone to cycle. when connected the green led lights up for a bit, but then goes off, then back on, then red.....repeatedly. The device only appears in device manager as 'S1 boot load' when green. This gives a very short window to try to do anything.

Wrong flashtool, download the one from the Dev section and flash a stock FTF
Sent from my C6903 using XDA Premium 4 mobile app

gregbradley said:
Wrong flashtool, download the one from the Dev section and flash a stock FTF
Sent from my C6903 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Oh right, first mistake then. The phone will still need unlocking first though I assume?

FASTdan2 said:
Oh right, first mistake then. The phone will still need unlocking first though I assume?
Click to expand...
Click to collapse
No, flashing a stock firmware works with locked bootloader

FASTdan2 said:
Oh right, first mistake then. The phone will still need unlocking first though I assume?
Click to expand...
Click to collapse
St.Jimmy90 said:
No, flashing a stock firmware works with locked bootloader
Click to expand...
Click to collapse
You do not even need root.

FASTdan2 said:
So I had a go at the above - got the flash tool installed (Emma?) etc and managed to get the software to see the phone - unfortunately though I had neglected to mention the phone is locked to a particular network, which Emma politely informs me.
So, I have attempted to follow unlocking instructions as per the sony instructions (on their website):
But I am stuck. I was getting nothing when using the volume down button and connecting. To get the computer to see the phone I have to press and hold the power button, the red led starts blinking 3 times, repeatedly. This causes windows to recognise the phone when plugged in via usb, but I was not being asked for drivers (as per sony step 13). I found the device in device manager and uninstalled drivers in an attempt to force this. Now all that happens is the device appears in the list as 'S1 Boot Load' with a yellow exclamation mark. However I have then tried installing drivers manually from the location where I copied 'android_winusb' to, but this does not work.
To compound the issue I think the battery problem is causing the phone to cycle. when connected the green led lights up for a bit, but then goes off, then back on, then red.....repeatedly. The device only appears in device manager as 'S1 boot load' when green. This gives a very short window to try to do anything.
Click to expand...
Click to collapse
I've been dealing with a similar problem. When connected to a wall charger is your phone cycling from Green to Red and keeps doing that? Also have you installed Sony PC Companion maybe your phone will get recognized from the drivers in that install.

Same problem
Hi, I am currently having the same problem. I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing i'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!

[Q] Xperia T will not go past Sony logo

Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!

1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?

Also flashmode and fastboot and adb dont work on windows 8(.1)

gregbradley said:
1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?
Click to expand...
Click to collapse
Its not even booting, past the Sony logo so i cannot do anything (i can't do step 1 as you've asked). Its literally a bootloop. Can you give me step-by-step instructions to get out of this bootloop? I tried to install custom ROM but it died on me, and now its on the bootloop, which i can't get passed.
hhamzah49 said:
Also flashmode and fastboot and adb dont work on windows 8(.1)
Click to expand...
Click to collapse
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
I have given my phone to the manufacturers to try and sort out but I have a feeling they will refuse to fix it, so any help would be appreciated. If i use a windows 7 machine, would it work? If so, how do I fix it such that it exits bootloop and allows me to access my phone. I don't mind losing all my data (although i think its lost anyway lol)
P.S. thanks for the reply.

fizstarrr said:
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
Click to expand...
Click to collapse
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.

immerblind said:
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.
Click to expand...
Click to collapse
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?

fizstarrr said:
Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!
Click to expand...
Click to collapse
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.

Unknownkj said:
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.
Click to expand...
Click to collapse
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:

fizstarrr said:
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:
Click to expand...
Click to collapse
Hello. Have you tried hard reset?
Press power button and vol up key together until it vibrates. Phone should start up?
Sent from my LT30p using xda premium

fizstarrr said:
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?
Click to expand...
Click to collapse
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things

LaZiODROID said:
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things
Click to expand...
Click to collapse
I'll try windows 7 when I get it back. And wow really? I didn't realise that using different cables actually made a difference? At the end of the day, if it charges the phone it should work! Lol, Sony know how to make things real complicated!

Experia T stuck on SONY logo
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!

HvdW said:
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!
Click to expand...
Click to collapse
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.

St.Jimmy90 said:
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.
Click to expand...
Click to collapse
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?

HvdW said:
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?
Click to expand...
Click to collapse
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!

fizstarrr said:
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!
Click to expand...
Click to collapse
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.

HvdW said:
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.
Click to expand...
Click to collapse
Ah that sucks! Are you not on windows 8? I've heard that windows 8 and flashtools don't get along, but if you're saying you've got your device into fastboot you should be able to flash it using flashtools!

Sony Xperia T LT30p dead resolved
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein

HvdW said:
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein
Click to expand...
Click to collapse
Hey so I ran into this same problem! my phone wouldn't do anything except boot up to the Sony screen, no lights no charging nothing
I figured it out, at least for me
>Have your flash ready to go via Flashtool
>Have your phone plugged into your computer via USB
>Hold the volume down button and then while holding it turn it on
you should have your green light and may have to hold the volume button the whole time until its done flashing.
Hope this works

FIX!
Hey the same thing happened to my xp T few days ago. My phone was rooted with UB. I was stuck on SONY LOGO too n my phone was rebooting from there repeatedly but I was managed to get into cwm n I installeddifferent kernels + Rome but it was no good. Like u said in your OP I couldn't get into flashmood too. When I select the firmware flashtools say preparing files then the phone reboots! Then flashtools say device disconnected!! The solution for this is when flashtools says device disconnected pull the usb cable n press vol up with power button n turn off phone. Then once turned off straight away press vol down n plug in usb cable n flashtools will start flashing. The important thing here is not to close the window that pops up when flashtool say device disconnected in red. Hope this helps, same prob worked for me so should work for you! Peace

z1 fully Dead Hard Brick

z1 completely dead, I instaled hi hackers rom and went well after finishing flashing i did'nt get network of airtel and instaled baseband of 3rd party and it is completely dead nothing is working when i press volume+on button it vibrates 3 times thats it and nothing is displayed and when i put to the charge it shows red light and stops,can anbody help me out from this, please only 3 months old my z1 and sorry for my english ....and can anbody reply friends?
Is it getting red led when I try to charge it ? I don't understand what went wrong.
I had it for about 24 hours on the charger without any signs of "life" in the "mobile".
Hard reset.
Flash a stock FTF using flashtool.
I went through the process of flashing a FTF with flashtool. and its showing....
27/059/2014 02:59:50 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.1.G.2.257. Customization : GLOBAL-LTE (1277-1398)
27/059/2014 02:59:50 - INFO - Preparing files for flashing
27/000/2014 03:00:36 - INFO - Please connect your device into flashmode.
27/001/2014 03:01:22 - INFO - Device disconnected
27/001/2014 03:01:26 - INFO - Device connected with USB debugging off
27/001/2014 03:01:26 - INFO - For 2011 devices line, be sure you are not in MTP mode
27/001/2014 03:01:35 - INFO - Device disconnected
27/001/2014 03:01:39 - INFO - Device connected with USB debugging off
27/001/2014 03:01:39 - INFO - For 2011 devices line, be sure you are not in MTP mode
can anybody come with this solution........?

as I said in the other thread, turn on usb debugging

if you cant do anything and powering on or connecting your phone to computer or charging it just makes the red led blink, it means its hard bricked. you may need to use test point
but if you dont have baseband and your device runs, try to flash a new modem(i dont know if its available for z1 or not)
and as i see you were trying to flash a much old ftf ... after 4.3 , flashing older than them will make the modem not work.so if you can get in to flash mode try to flash a newer frameware

NiM72NiK said:
if you cant do anything and powering on or connecting your phone to computer or charging it just makes the red led blink, it means its hard bricked. you may need to use test point
but if you dont have baseband and your device runs, try to flash a new modem(i dont know if its available for z1 or not)
and as i see you were trying to flash a much old ftf ... after 4.3 , flashing older than them will make the modem not work.so if you can get in to flash mode try to flash a newer frameware
Click to expand...
Click to collapse
No i can't go into Flash Mode

srichinu said:
No i can't go into Flash Mode
Click to expand...
Click to collapse
unfortunately your phone is hard bricked as its blinking red to everything and must open your phone and hard repair it
follow the instructions on the link below
hope it helps:
http://forum.xda-developers.com/showthread.php?t=2646405
and this is the latest s1 boot .use this one
forum.xda-developers.com/attachment.php?attachmentid=2771435&d=1401467170

ok u give more details for test point and confirm we can try for z1 sir

gregbradley said:
as I said in the other thread, turn on usb debugging
Click to expand...
Click to collapse
no i cant turn usb debugging its full dead ?

srichinu said:
z1 completely dead, I instaled hi hackers rom and went well after finishing flashing i did'nt get network of airtel and instaled baseband of 3rd party and it is completely dead nothing is working when i press volume+on button it vibrates 3 times thats it and nothing is displayed and when i put to the charge it shows red light and stops,can anbody help me out from this, please only 3 months old my z1 and sorry for my english ....and can anbody reply friends?
Is it getting red led when I try to charge it ? I don't understand what went wrong.
I had it for about 24 hours on the charger without any signs of "life" in the "mobile".
Hard reset.
Flash a stock FTF using flashtool.
I went through the process of flashing a FTF with flashtool. and its showing....
27/059/2014 02:59:50 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.1.G.2.257. Customization : GLOBAL-LTE (1277-1398)
27/059/2014 02:59:50 - INFO - Preparing files for flashing
27/000/2014 03:00:36 - INFO - Please connect your device into flashmode.
27/001/2014 03:01:22 - INFO - Device disconnected
27/001/2014 03:01:26 - INFO - Device connected with USB debugging off
27/001/2014 03:01:26 - INFO - For 2011 devices line, be sure you are not in MTP mode
27/001/2014 03:01:35 - INFO - Device disconnected
27/001/2014 03:01:39 - INFO - Device connected with USB debugging off
27/001/2014 03:01:39 - INFO - For 2011 devices line, be sure you are not in MTP mode
can anybody come with this solution........?
Click to expand...
Click to collapse
Open Flash Tools, select FTF and wait till it says connect your phone. Now hold down volume and plug in USB to PC
If continued, be happy
If not, unplug fully, and then again hold down volume, and then a bit plug in, like image in the link below
Sorry for bad explanation
I experienced brick about five times, and this my own-made method help me
http://d-h.st/FrT

I did has ur instruction red led is lighting continuesly and driver intalling is happening but usb is not recongised and flashing is not done?

srichinu said:
I did has ur instruction red led is lighting continuesly and driver intalling is happening but usb is not recongised and flashing is not done?
Click to expand...
Click to collapse
I think I got what you said
By this method, maybe PC says USB not recognized, but flashing will be done, with no problem
Sent from my C6903 using Tapatalk

MR. Saeed, as he says, its hard bricked . no flash mode or anything..fully dead.. so he cant do anything with flashtool.. seams just opening the phone and fix it in emergency mod is the only solution here ...

NiM72NiK said:
MR. Saeed, as he says, its hard bricked . no flash mode or anything..fully dead.. so he cant do anything with flashtool.. seams just opening the phone and fix it in emergency mod is the only solution here ...
Click to expand...
Click to collapse
Sorry, I did not fully read the first post
I think he just should call emergency to move his phone to hospital
Sent from my C6903 using Tapatalk

SaeedFazlollahzadeh said:
Sorry, I did not fully read the first post
I think he just should call emergency to move his phone to hospital
Sent from my C6903 using Tapatalk
Click to expand...
Click to collapse
He has to open it connect the testpoint to GND and conmect the usb cable and repair it in emergency mode...

srichinu said:
No i can't go into Flash Mode
Click to expand...
Click to collapse
Next time do not be so fast and lazy to read instructions provided by developer of the thing you have flashed. Being fast and thinking wrong and fast sometimes produce fatal thing to the your phone. I am sure you will be no lazy next time and I am sure you will be very careful in operations with your next phone
Whats happening when you press and hold for about 5 secconds power + volumeup button? If you see vibration than you are not in hard brick! If there is no vibration but your phone flashing red all time than its hard brick! If not hard brick you can enter into fastboot mode: disconnect usb cable, press and hold power+volume up until you see vibration, than hold volume up button and in same time connect usb cable. After than you must see blue led! If no blue led than probably try to replace usb drivers by installing sony pc companion, reboot computer after that! Allso make sure comuter device manager detect your phone propertly! After that try again all steps. If this not help and you have red light all time than probably your phone is dead! Hope this help.

[Q] Hard Brick or he die? :)

Hi everyone, i'm newbie here and, for first i'm so sorry formy bad english, but, anyway
My problem is serously hard, someone here having problem like me, for example - click.
Okey, so now my problem: Xperia C5303, i'm don't know which firmware was stay at this XPS until them became bricked, not my phone
Phone isn't boot, don't react to power\+ and - button, when i try to connect it to PC, the phone light up red when attempting to charge, remain solid red for 10 minutes before the LED switches off for around 5-7 minutes.The phone then use to go back to the red LED and the loop would continue. I take a multimeter, plug it at + and - to the batttery, when i connecting USB, RED light up, voltage going to ~3.20V, after RED light switches off and voltage going to ~2.8V and phone again charged to 3.2V and loop, loop, loop. If i disconnect USB cable with 2.9V-3.1V and press PWR button, RED light blinks 3 times, like them discharged. So, i can't put phone to Flashmode\Fastboot mod, for first i think, maybe not enough charging on battery for start flashmode\fastboot, BUT, I was wrong, i charge battery for 4-5Hrs without phone, just use AAA and AA charger laugh,voltage around 3.6V, connected to phone, connect USB and...nothing, just nothing, don't react to anyting, as I understand USB transmits a signal if battery is discharging And, when i connect charged battery and click pwr button, voltage started to fall as if the phone is switched on.
Soooo, in Flashtool, when i connected phone with pressed - button\+ button, PC determine phone like HID device!!!, wooow, how?
I install all drivers that i know, SEUS, PC Compasion, Flastool drivers, drivers from XDA worum for all Sony phones.
Flashtool log:
25/010/2014 15:10:11 - INFO - Device connected with USB debugging off
25/010/2014 15:10:11 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/010/2014 15:10:17 - INFO - Device disconnected
DeviceID in device manager:
USB\VID_0FCE&PID_D17B&REV_0000
USB\VID_0FCE&PID_D17B
So, what to do for debrick this XSP?
Maybe try to install XP? Ah, my OS is Win7 x64
Thanks for all your asweres, best regards, LiquidNettle :3
Stay awesome.
______
I will add, that's what Flashtool showin when pressing Devices - Check drivers:
5/006/2014 16:06:17 - INFO - Device connected with USB debugging off
25/006/2014 16:06:17 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/006/2014 16:06:20 - INFO - List of connected devices (Device Id) :
25/006/2014 16:06:20 - INFO - - USB\VID_0FCE&PID_D17B\5&10EF021E&0&2 Driver installed : true
25/006/2014 16:06:21 - INFO - - HID\VID_0FCE&PID_D17B\6&17F701B0&2&0000 Driver installed : true
25/006/2014 16:06:21 - INFO - List of ADB devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:21 - INFO - List of fastboot devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:22 - INFO - Device disconnected

Flash an FTF file (original firmware) using Flashtool.
They can be found on this forum.

Gamm86 said:
Flash an FTF file (original firmware) using Flashtool.
They can be found on this forum.
Click to expand...
Click to collapse
Thanks for fast answer but how? I can't put phone to flashmode!

Let your phone charge with a wall socket charger (preferably the original one) for atleast 12 hours and then try again.

Done, I will inform you 12 hours pass

@Liquid have this Problem too. Have u found a answer
Gesendet von meinem SGP521 mit Tapatalk 4

arty06 said:
@Liquid have this Problem too. Have u found a answer
Gesendet von meinem SGP521 mit Tapatalk 4
Click to expand...
Click to collapse
Hi arty
No, not found yet :c
Right now, whaiting 12hrs like Gamm say. I installed WinXP and he, too, see the phone as a HID device, WHY? And, if i trying put original, ADB drivers i get an error :c
So, we can't coop with you, arty and try to find how to unbrick our phones

@LiquidNettle
Your phone is indeed hard bricked. Sorry for that. You can try connecting to flashmode by using the technique this guy did: http://forum.xda-developers.com/showpost.php?p=54541794&postcount=1870

[/COLOR]
LiquidNettle said:
Hi arty
No, not found yet :c
Right now, whaiting 12hrs like Gamm say. I installed WinXP and he, too, see the phone as a HID device, WHY? And, if i trying put original, ADB drivers i get an error :c
So, we can't coop with you, arty and try to find how to unbrick our phones
Click to expand...
Click to collapse
Do u have CWM on ur Device? I flash my ROM new with it and it works.:victory:

LiquidNettle said:
Hi everyone, i'm newbie here and, for first i'm so sorry formy bad english, but, anyway
My problem is serously hard, someone here having problem like me, for example - click.
Okey, so now my problem: Xperia C5303, i'm don't know which firmware was stay at this XPS until them became bricked, not my phone
Phone isn't boot, don't react to power\+ and - button, when i try to connect it to PC, the phone light up red when attempting to charge, remain solid red for 10 minutes before the LED switches off for around 5-7 minutes.The phone then use to go back to the red LED and the loop would continue. I take a multimeter, plug it at + and - to the batttery, when i connecting USB, RED light up, voltage going to ~3.20V, after RED light switches off and voltage going to ~2.8V and phone again charged to 3.2V and loop, loop, loop. If i disconnect USB cable with 2.9V-3.1V and press PWR button, RED light blinks 3 times, like them discharged. So, i can't put phone to Flashmode\Fastboot mod, for first i think, maybe not enough charging on battery for start flashmode\fastboot, BUT, I was wrong, i charge battery for 4-5Hrs without phone, just use AAA and AA charger laugh,voltage around 3.6V, connected to phone, connect USB and...nothing, just nothing, don't react to anyting, as I understand USB transmits a signal if battery is discharging And, when i connect charged battery and click pwr button, voltage started to fall as if the phone is switched on.
Soooo, in Flashtool, when i connected phone with pressed - button\+ button, PC determine phone like HID device!!!, wooow, how?
I install all drivers that i know, SEUS, PC Compasion, Flastool drivers, drivers from XDA worum for all Sony phones.
Flashtool log:
25/010/2014 15:10:11 - INFO - Device connected with USB debugging off
25/010/2014 15:10:11 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/010/2014 15:10:17 - INFO - Device disconnected
DeviceID in device manager:
USB\VID_0FCE&PID_D17B&REV_0000
USB\VID_0FCE&PID_D17B
So, what to do for debrick this XSP?
Maybe try to install XP? Ah, my OS is Win7 x64
Thanks for all your asweres, best regards, LiquidNettle :3
Stay awesome.
______
I will add, that's what Flashtool showin when pressing Devices - Check drivers:
5/006/2014 16:06:17 - INFO - Device connected with USB debugging off
25/006/2014 16:06:17 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/006/2014 16:06:20 - INFO - List of connected devices (Device Id) :
25/006/2014 16:06:20 - INFO - - USB\VID_0FCE&PID_D17B\5&10EF021E&0&2 Driver installed : true
25/006/2014 16:06:21 - INFO - - HID\VID_0FCE&PID_D17B\6&17F701B0&2&0000 Driver installed : true
25/006/2014 16:06:21 - INFO - List of ADB devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:21 - INFO - List of fastboot devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:22 - INFO - Device disconnected
Click to expand...
Click to collapse
@Liquid: I am also facing the same problem. My phone is not responding to any hardware activity. Did you tried to connect the phone in flash mode after removing battery.? Tell me if this works.

Hi all guys, thanks for your activity ^)
TechnoSparks said:
@LiquidNettle
Your phone is indeed hard bricked. Sorry for that. You can try connecting to flashmode by using the technique this guy did: http://forum.xda-developers.com/showpost.php?p=54541794&postcount=1870
Click to expand...
Click to collapse
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
arty06 said:
[/COLOR]
Do u have CWM on ur Device? I flash my ROM new with it and it works.:victory:
Click to expand...
Click to collapse
I don't know what this phone have or haven't, i doesnt see this phone when them switched on, but congratulations you're lucky
And i can't isntall anything, beaucase i can't enter in fastboot :c
SumitDhingra said:
@Liquid: I am also facing the same problem. My phone is not responding to any hardware activity. Did you tried to connect the phone in flash mode after removing battery.? Tell me if this works.
Click to expand...
Click to collapse
How? Connect USB with pressing - button and remove battery or remove batter and connect USB with minus button?

Oh, somethimes, phone conenctng as QHSUSB_DLOAD what is it?

LiquidNettle said:
Hi all guys, thanks for your activity ^)
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
I don't know what this phone have or haven't, i doesnt see this phone when them switched on, but congratulations you're lucky
And i can't isntall anything, beaucase i can't enter in fastboot :c
How? Connect USB with pressing - button and remove battery or remove batter and connect USB with minus button?
Click to expand...
Click to collapse
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?

SumitDhingra said:
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?
Click to expand...
Click to collapse
Xperia SP's battery is built-in.
LiquidNettle said:
Hi all guys, thanks for your activity ^)
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
Click to expand...
Click to collapse
I can't check it out, but do stay tune as I will post it shortly.
You do not need to think about how was it detected by your computer. You just need to make sure it is connected to Flashtool. Either way, you must retry the method I have linked you to, or try the one in this link: http://forum.xda-developers.com/showpost.php?p=54634835&postcount=35
Does your phone able to connect to your computer by any means? I mean does Windows ever detect any presence of device (noticeably the usual "installing driver" balloon or the "hardware connect" sound)?

SumitDhingra said:
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?
Click to expand...
Click to collapse
Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
TechnoSparks said:
Xperia SP's battery is built-in.
I can't check it out, but do stay tune as I will post it shortly.
You do not need to think about how was it detected by your computer. You just need to make sure it is connected to Flashtool. Either way, you must retry the method I have linked you to, or try the one in this link: http://forum.xda-developers.com/showpost.php?p=54634835&postcount=35
Does your phone able to connect to your computer by any means? I mean does Windows ever detect any presence of device (noticeably the usual "installing driver" balloon or the "hardware connect" sound)?
Click to expand...
Click to collapse
Still nothing
Yeah, its all okey

E=LiquidNettle;55717389]Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
Still nothing
Yeah, its all okey[/QUOTE]
Can you tell me how did you bricked your phone?

SumitDhingra said:
E=LiquidNettle;55717389]Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
Still nothing
Yeah, its all okey
Click to expand...
Click to collapse
Can you tell me how did you bricked your phone?[/QUOTE]
I can't :laugh:
Its not my phone, I got a freebie. Guy, who gave me this phone say, what his girlfriend dropped and LCD is damaged, that's all.

Phone not powering up
Phone not powering up
My phone Sony Xperia SP went dead after flashing the kernal mentioned in http://forum.xda-developers.com/show...697865&page=36
Not showing any activity.
Now phone is not powering on ..
I was having a unlocked bootloader + root + cm11
I flashed the new kernal using Flash tool.
Can anyone please help me.
This issue is resolved.
Please find the solution here

sanusunnyk said:
Phone not powering up
My phone Sony Xperia SP went dead after flashing the kernal mentioned in http://forum.xda-developers.com/show...697865&page=36
Not showing any activity.
Now phone is not powering on ..
I was having a unlocked bootloader + root + cm11
I flashed the new kernal using Flash tool.
Can anyone please help me.
Click to expand...
Click to collapse
Flash stock ftf via flashtool

rdlegy said:
Flash stock ftf via flashtool
Click to expand...
Click to collapse
His phone has already working normally. He should edit the question when he succeeded with his phone though.

Help on xperiz z1: dead during update.

Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil

sunil14353 said:
Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
Click to expand...
Click to collapse
hi
are you ready to disassemble your xperia?
did you try this ???
look here
http://sony.yt/topic/7324-english-t...oot-in-sony-xperia-z-c6602-c6603-c6606-c6616/
sorry to put a link from another forum.

Hey i'm not exactly sure what you mean by the description, but to enter flash mode you need to turn off the device - then hold down the volume-down key whilst inserting the usb. Keep holding down the volume-down key until you seen some green notification lights flash and you should be in flashmode and ready to flash a FTF. It should also say on flashtool that "Device has entered flashmode" or something like that.