Help on xperiz z1: dead during update. - Xperia Z1 Q&A, Help & Troubleshooting

Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil

sunil14353 said:
Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
Click to expand...
Click to collapse
hi
are you ready to disassemble your xperia?
did you try this ???
look here
http://sony.yt/topic/7324-english-t...oot-in-sony-xperia-z-c6602-c6603-c6606-c6616/
sorry to put a link from another forum.

Hey i'm not exactly sure what you mean by the description, but to enter flash mode you need to turn off the device - then hold down the volume-down key whilst inserting the usb. Keep holding down the volume-down key until you seen some green notification lights flash and you should be in flashmode and ready to flash a FTF. It should also say on flashtool that "Device has entered flashmode" or something like that.

Related

[Q] Xperia T will not go past Sony logo

Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!
1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?
Also flashmode and fastboot and adb dont work on windows 8(.1)
gregbradley said:
1) Dial *#*#7378423#*#* and goto software info/configuaration. If it says bootloader unlocked allowed: no, then you CANNOT unlock it via ANY means
2) If it says yes (I doubt it, because flashtool has already checked this) then you can.
3) Flashmode has nothing to do with bootloader. Press volume up to get into fastboot (Blue LED) for working with bootloader, press volume down (Green LED) to work in flashmode, which is for flashing FTF's.
4) If you are trying to flash a FTF, then do not connect the phone until it asks
5)Make sure you have gone to C:\flashtool\drivers and run drivers.exe. Ensure you choose fastboot, flashmode and TX drivers.
6) Make sure you are on the latest version of flashtool 0.9.13.1
Can I ask what you are actually trying to do?
Click to expand...
Click to collapse
Its not even booting, past the Sony logo so i cannot do anything (i can't do step 1 as you've asked). Its literally a bootloop. Can you give me step-by-step instructions to get out of this bootloop? I tried to install custom ROM but it died on me, and now its on the bootloop, which i can't get passed.
hhamzah49 said:
Also flashmode and fastboot and adb dont work on windows 8(.1)
Click to expand...
Click to collapse
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
I have given my phone to the manufacturers to try and sort out but I have a feeling they will refuse to fix it, so any help would be appreciated. If i use a windows 7 machine, would it work? If so, how do I fix it such that it exits bootloop and allows me to access my phone. I don't mind losing all my data (although i think its lost anyway lol)
P.S. thanks for the reply.
fizstarrr said:
Oh okay. I'm using windows 8.1, so what would I do to fix the issue?
Click to expand...
Click to collapse
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.
immerblind said:
use windows 7 or linux. i read about problems with win8.1 too. thats why i not updated my win8 yet.
Click to expand...
Click to collapse
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?
fizstarrr said:
Hi, I have tried to use flashtools and I've got all the necessary drivers (I think) but once I put hold power button and vol+ (3 vibrations), then press vol-, connect to pc via USB and I get a temporary green led, which goes after about 5 seconds, and then my phone disconnects from my computer again and i get a constant red led while the Sony logo appears. I really need my phone to work Could someone out there please help with this! I would really appreciate if someone responded very soon as I would like to get this sorted as soon as possible. Flashtools gives me these messages:
22/012/2013 23:12:07 - INFO - Device disconnected
22/029/2013 23:29:07 - INFO - Device connected in flash mode
22/029/2013 23:29:18 - INFO - Device disconnected
Also one more thing I'd like to add.. Once I go into that BLU thing, it keeps on asking me what device I have, so I select Xperia T and then it gives the following messages:
22/052/2013 22:52:26 - INFO - Your phone bootloader cannot be officially unlocked
22/052/2013 22:52:26 - INFO - You can now unplug and restart your phone
Might this have something to do with it? Any suggestions would be grateful! I've been at this for hours now and need to get this sorted
Thanks to any kind person who helps fix this!
Click to expand...
Click to collapse
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.
Unknownkj said:
I'm sure your batt is dead. Try the rubber band method. Give it like 2/3 rounds of it on the power button and hold it and plug in charger. it should charge with red led on. Pull battery and try again if it does not charge. Give it some charging and it should be able to enter flashmode to flash stock.
Click to expand...
Click to collapse
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:
fizstarrr said:
I don't think the battery is dead, as the led would just blink and wouldn't even show me the Sony logo.. Everytime i use the phone with the charger it goes into the bootloop, looping around the Sony logo and then switching off again, then the sony logo will show again, etc. I've sent it off to Sony manufaturers. Would they fix it (even if the manufacturers warranty is void)? Like, even if they charge a little (hopefully not stupid amounts of money lol)? If not, i'm going to try and use flashtool on windows 7 machine and hope that it works, as I've heard flashmode and fastboot and adb do not work on windows 8(.1), which is what im currently using :crying:
Click to expand...
Click to collapse
Hello. Have you tried hard reset?
Press power button and vol up key together until it vibrates. Phone should start up?
Sent from my LT30p using xda premium
fizstarrr said:
Question is, will is definitely work if i use windows 7? I.e. is the fact that i'm using windows 8.1 the reason why it's not working?
Click to expand...
Click to collapse
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things
LaZiODROID said:
Yes (or, at least its definitely one of the reasons). Use Win 8 or Win 7 or Win XP.
If after that point you still have trouble with it sticking to flashmode: I also had trouble flashing via flashmode with one of my USB ports. I like to use the front ones on my PC but they don't work for every device. There is also a USB cable that I have that does not work for flashmode. Consider these 2 things
Click to expand...
Click to collapse
I'll try windows 7 when I get it back. And wow really? I didn't realise that using different cables actually made a difference? At the end of the day, if it charges the phone it should work! Lol, Sony know how to make things real complicated!
Experia T stuck on SONY logo
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!
HvdW said:
Help, another help
I read about the leaked 4.3 and the latest 4.4
Did much flashing with HTC Desire.
Now I made a big mistake trying something with my Xperia T
Using DooMLorD flashtool I got into fastboot mode and then clicked on 'Reboot device into system'
I WISH I HADN'T
Now my Xperia T is dead.
Starting up it gets stuck on the SONY logo, nothing, nothing happens.
Please help me recover the device!
Click to expand...
Click to collapse
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.
St.Jimmy90 said:
It's just a soft brick. What did you wanted to flash? Just flash a stock .ftf file with flashtool, or a kernel with recovery.
Click to expand...
Click to collapse
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?
HvdW said:
Well, first of all I want the phone to start up normally again so that I can use it.
What I did achieve up till now is that I can get it connected to flashtool in Fastboot mode.
I guess this gives me the opportunity to flash a boot.img first so that I can install 4.4 or 4.3 later.
But first things first.
Do you think flashing a boot.img could restore the phone in a state that it functions as a normal phone again?
Click to expand...
Click to collapse
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!
fizstarrr said:
My xperia t has gone in for repair. Before considering this though, could you try one thing to see if it'll help restore phone? Go to your PC companion (and no, its not a standard recovery which i'm going to suggest so keep reading!). Once you have done this, click on "Support zone". Click "Start" on the "Phone/tablet software update" option. Note, you do not need to plug in your device yet!. You should get an error message coming up saying device not connected. And once you get this, there should be a message asking you whether you are having "severe problems with your phone/tablet". There's a "repair my phone/tablet" hyperlink. I want you to click that and NOT the connect button. Once you have clicked that, please follow the on screen instructions. Tell me if this works for you I hope it does!
Click to expand...
Click to collapse
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.
HvdW said:
No it dod not.
Why?
Because SONY decided that I have made changes to my phone and SONY now refuses to repair my device.
Click to expand...
Click to collapse
Ah that sucks! Are you not on windows 8? I've heard that windows 8 and flashtools don't get along, but if you're saying you've got your device into fastboot you should be able to flash it using flashtools!
Sony Xperia T LT30p dead resolved
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein
HvdW said:
OK, here it is for those interested on how to revive a dead Xperia device.
Yesterday my phone stalled at the SONY logo.
Nothing could be done anymore.
My phone has returned into normal state thanks to SonyXperiakiasT :good:
Follow this thread: http://forum.xda-developers.com/showthread.php?t=2315572
Howto get into a state that one can flash the phone.
- download: LT30P_9.1.A.1.141_PL.ftf (the original firmware)
- install and activate flashtool-0.9.13.0-windows.exe
- at the SONY logo push on/off, vol-up and vol-down together
- when the phone vibrates an the logo disappears release all buttons and immediately after push on/off and vol-up button
- when phone vibrates release on/off button, keep pushing vol-up button and plug in USB cable from computer
- you will be in a state with a blue light at the top left of your phone.
- however you want to get in a state with a green led
- push vol-down and on/off
- unplug the USB
- wait for the phone to vibrate
- release the on/off button and plug in the USB
- Follow the instructions in the thread mentioned above and your phone will be revived.
All the pushing, releasing, plugging and unplugging is a quite delicate affair.
I tried it during several hours before I got a bit of grip on it and still I am not shure how I got into the green led state.
Try it, be patient and be shure that repair is within reach as soon as you have a green LED on your phone.
Good luck!
Hein
Click to expand...
Click to collapse
Hey so I ran into this same problem! my phone wouldn't do anything except boot up to the Sony screen, no lights no charging nothing
I figured it out, at least for me
>Have your flash ready to go via Flashtool
>Have your phone plugged into your computer via USB
>Hold the volume down button and then while holding it turn it on
you should have your green light and may have to hold the volume button the whole time until its done flashing.
Hope this works
FIX!
Hey the same thing happened to my xp T few days ago. My phone was rooted with UB. I was stuck on SONY LOGO too n my phone was rebooting from there repeatedly but I was managed to get into cwm n I installeddifferent kernels + Rome but it was no good. Like u said in your OP I couldn't get into flashmood too. When I select the firmware flashtools say preparing files then the phone reboots! Then flashtools say device disconnected!! The solution for this is when flashtools says device disconnected pull the usb cable n press vol up with power button n turn off phone. Then once turned off straight away press vol down n plug in usb cable n flashtools will start flashing. The important thing here is not to close the window that pops up when flashtool say device disconnected in red. Hope this helps, same prob worked for me so should work for you! Peace

[Q] Hard Brick or he die? :)

Hi everyone, i'm newbie here and, for first i'm so sorry formy bad english, but, anyway
My problem is serously hard, someone here having problem like me, for example - click.
Okey, so now my problem: Xperia C5303, i'm don't know which firmware was stay at this XPS until them became bricked, not my phone
Phone isn't boot, don't react to power\+ and - button, when i try to connect it to PC, the phone light up red when attempting to charge, remain solid red for 10 minutes before the LED switches off for around 5-7 minutes.The phone then use to go back to the red LED and the loop would continue. I take a multimeter, plug it at + and - to the batttery, when i connecting USB, RED light up, voltage going to ~3.20V, after RED light switches off and voltage going to ~2.8V and phone again charged to 3.2V and loop, loop, loop. If i disconnect USB cable with 2.9V-3.1V and press PWR button, RED light blinks 3 times, like them discharged. So, i can't put phone to Flashmode\Fastboot mod, for first i think, maybe not enough charging on battery for start flashmode\fastboot, BUT, I was wrong, i charge battery for 4-5Hrs without phone, just use AAA and AA charger laugh,voltage around 3.6V, connected to phone, connect USB and...nothing, just nothing, don't react to anyting, as I understand USB transmits a signal if battery is discharging And, when i connect charged battery and click pwr button, voltage started to fall as if the phone is switched on.
Soooo, in Flashtool, when i connected phone with pressed - button\+ button, PC determine phone like HID device!!!, wooow, how?
I install all drivers that i know, SEUS, PC Compasion, Flastool drivers, drivers from XDA worum for all Sony phones.
Flashtool log:
25/010/2014 15:10:11 - INFO - Device connected with USB debugging off
25/010/2014 15:10:11 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/010/2014 15:10:17 - INFO - Device disconnected
DeviceID in device manager:
USB\VID_0FCE&PID_D17B&REV_0000
USB\VID_0FCE&PID_D17B
So, what to do for debrick this XSP?
Maybe try to install XP? Ah, my OS is Win7 x64
Thanks for all your asweres, best regards, LiquidNettle :3
Stay awesome.
______
I will add, that's what Flashtool showin when pressing Devices - Check drivers:
5/006/2014 16:06:17 - INFO - Device connected with USB debugging off
25/006/2014 16:06:17 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/006/2014 16:06:20 - INFO - List of connected devices (Device Id) :
25/006/2014 16:06:20 - INFO - - USB\VID_0FCE&PID_D17B\5&10EF021E&0&2 Driver installed : true
25/006/2014 16:06:21 - INFO - - HID\VID_0FCE&PID_D17B\6&17F701B0&2&0000 Driver installed : true
25/006/2014 16:06:21 - INFO - List of ADB devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:21 - INFO - List of fastboot devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:22 - INFO - Device disconnected
Flash an FTF file (original firmware) using Flashtool.
They can be found on this forum.
Gamm86 said:
Flash an FTF file (original firmware) using Flashtool.
They can be found on this forum.
Click to expand...
Click to collapse
Thanks for fast answer but how? I can't put phone to flashmode!
Let your phone charge with a wall socket charger (preferably the original one) for atleast 12 hours and then try again.
Done, I will inform you 12 hours pass
@Liquid have this Problem too. Have u found a answer
Gesendet von meinem SGP521 mit Tapatalk 4
arty06 said:
@Liquid have this Problem too. Have u found a answer
Gesendet von meinem SGP521 mit Tapatalk 4
Click to expand...
Click to collapse
Hi arty
No, not found yet :c
Right now, whaiting 12hrs like Gamm say. I installed WinXP and he, too, see the phone as a HID device, WHY? And, if i trying put original, ADB drivers i get an error :c
So, we can't coop with you, arty and try to find how to unbrick our phones
@LiquidNettle
Your phone is indeed hard bricked. Sorry for that. You can try connecting to flashmode by using the technique this guy did: http://forum.xda-developers.com/showpost.php?p=54541794&postcount=1870
[/COLOR]
LiquidNettle said:
Hi arty
No, not found yet :c
Right now, whaiting 12hrs like Gamm say. I installed WinXP and he, too, see the phone as a HID device, WHY? And, if i trying put original, ADB drivers i get an error :c
So, we can't coop with you, arty and try to find how to unbrick our phones
Click to expand...
Click to collapse
Do u have CWM on ur Device? I flash my ROM new with it and it works.:victory:
LiquidNettle said:
Hi everyone, i'm newbie here and, for first i'm so sorry formy bad english, but, anyway
My problem is serously hard, someone here having problem like me, for example - click.
Okey, so now my problem: Xperia C5303, i'm don't know which firmware was stay at this XPS until them became bricked, not my phone
Phone isn't boot, don't react to power\+ and - button, when i try to connect it to PC, the phone light up red when attempting to charge, remain solid red for 10 minutes before the LED switches off for around 5-7 minutes.The phone then use to go back to the red LED and the loop would continue. I take a multimeter, plug it at + and - to the batttery, when i connecting USB, RED light up, voltage going to ~3.20V, after RED light switches off and voltage going to ~2.8V and phone again charged to 3.2V and loop, loop, loop. If i disconnect USB cable with 2.9V-3.1V and press PWR button, RED light blinks 3 times, like them discharged. So, i can't put phone to Flashmode\Fastboot mod, for first i think, maybe not enough charging on battery for start flashmode\fastboot, BUT, I was wrong, i charge battery for 4-5Hrs without phone, just use AAA and AA charger laugh,voltage around 3.6V, connected to phone, connect USB and...nothing, just nothing, don't react to anyting, as I understand USB transmits a signal if battery is discharging And, when i connect charged battery and click pwr button, voltage started to fall as if the phone is switched on.
Soooo, in Flashtool, when i connected phone with pressed - button\+ button, PC determine phone like HID device!!!, wooow, how?
I install all drivers that i know, SEUS, PC Compasion, Flastool drivers, drivers from XDA worum for all Sony phones.
Flashtool log:
25/010/2014 15:10:11 - INFO - Device connected with USB debugging off
25/010/2014 15:10:11 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/010/2014 15:10:17 - INFO - Device disconnected
DeviceID in device manager:
USB\VID_0FCE&PID_D17B&REV_0000
USB\VID_0FCE&PID_D17B
So, what to do for debrick this XSP?
Maybe try to install XP? Ah, my OS is Win7 x64
Thanks for all your asweres, best regards, LiquidNettle :3
Stay awesome.
______
I will add, that's what Flashtool showin when pressing Devices - Check drivers:
5/006/2014 16:06:17 - INFO - Device connected with USB debugging off
25/006/2014 16:06:17 - INFO - For 2011 devices line, be sure you are not in MTP mode
25/006/2014 16:06:20 - INFO - List of connected devices (Device Id) :
25/006/2014 16:06:20 - INFO - - USB\VID_0FCE&PID_D17B\5&10EF021E&0&2 Driver installed : true
25/006/2014 16:06:21 - INFO - - HID\VID_0FCE&PID_D17B\6&17F701B0&2&0000 Driver installed : true
25/006/2014 16:06:21 - INFO - List of ADB devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:21 - INFO - List of fastboot devices :
25/006/2014 16:06:21 - INFO - - none
25/006/2014 16:06:22 - INFO - Device disconnected
Click to expand...
Click to collapse
@Liquid: I am also facing the same problem. My phone is not responding to any hardware activity. Did you tried to connect the phone in flash mode after removing battery.? Tell me if this works.
Hi all guys, thanks for your activity ^)
TechnoSparks said:
@LiquidNettle
Your phone is indeed hard bricked. Sorry for that. You can try connecting to flashmode by using the technique this guy did: http://forum.xda-developers.com/showpost.php?p=54541794&postcount=1870
Click to expand...
Click to collapse
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
arty06 said:
[/COLOR]
Do u have CWM on ur Device? I flash my ROM new with it and it works.:victory:
Click to expand...
Click to collapse
I don't know what this phone have or haven't, i doesnt see this phone when them switched on, but congratulations you're lucky
And i can't isntall anything, beaucase i can't enter in fastboot :c
SumitDhingra said:
@Liquid: I am also facing the same problem. My phone is not responding to any hardware activity. Did you tried to connect the phone in flash mode after removing battery.? Tell me if this works.
Click to expand...
Click to collapse
How? Connect USB with pressing - button and remove battery or remove batter and connect USB with minus button?
Oh, somethimes, phone conenctng as QHSUSB_DLOAD what is it?
LiquidNettle said:
Hi all guys, thanks for your activity ^)
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
I don't know what this phone have or haven't, i doesnt see this phone when them switched on, but congratulations you're lucky
And i can't isntall anything, beaucase i can't enter in fastboot :c
How? Connect USB with pressing - button and remove battery or remove batter and connect USB with minus button?
Click to expand...
Click to collapse
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?
SumitDhingra said:
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?
Click to expand...
Click to collapse
Xperia SP's battery is built-in.
LiquidNettle said:
Hi all guys, thanks for your activity ^)
Try this - nothing :c
I think, problem in drivers, beaucase, why PC thinks that the phone is a HID-device?
If you can, please make me something for me, connect your phone to PC and, in device manager find Device ID of your XSP and write it here please. I'll try compare you ID and my, thanks
Click to expand...
Click to collapse
I can't check it out, but do stay tune as I will post it shortly.
You do not need to think about how was it detected by your computer. You just need to make sure it is connected to Flashtool. Either way, you must retry the method I have linked you to, or try the one in this link: http://forum.xda-developers.com/showpost.php?p=54634835&postcount=35
Does your phone able to connect to your computer by any means? I mean does Windows ever detect any presence of device (noticeably the usual "installing driver" balloon or the "hardware connect" sound)?
SumitDhingra said:
Remove battery and then connect USB with volume down button pressed.
My friend's Xperia E went into flash mode without battery, so there is a chance that SP will also get into flashmode without battery.
Or else try this if you had screwed your kernel:
Remove your phone's battery and put atleast 30-40% charged battery in it. Your can also charge your phone's battery by connecting it to another Xperia SP. Once you had 30-40% battery, try to boot your phone. It should get into bootloops, then you can connect it in flash mode.
I need to try 2nd method desperately but couldn't find an Xperia sp ...?
Click to expand...
Click to collapse
Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
TechnoSparks said:
Xperia SP's battery is built-in.
I can't check it out, but do stay tune as I will post it shortly.
You do not need to think about how was it detected by your computer. You just need to make sure it is connected to Flashtool. Either way, you must retry the method I have linked you to, or try the one in this link: http://forum.xda-developers.com/showpost.php?p=54634835&postcount=35
Does your phone able to connect to your computer by any means? I mean does Windows ever detect any presence of device (noticeably the usual "installing driver" balloon or the "hardware connect" sound)?
Click to expand...
Click to collapse
Still nothing
Yeah, its all okey
E=LiquidNettle;55717389]Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
Still nothing
Yeah, its all okey[/QUOTE]
Can you tell me how did you bricked your phone?
SumitDhingra said:
E=LiquidNettle;55717389]Hi again
I have two batteries, 1 was all time ucharged, beaucase phone can't charge them and 1 full charged. When i connect full battery phone do not respond to ANYTHING!
Connnecting USB - nothing, press PWR button - nothing. That is when the battery is charged to third-party way and connect to phone, usb stops responding. And when connecting USB to phone with fully charged battery begins to run and phone heated on multimetr voltage going from 3.72V to 3.69V and after 1-2H to 2.8V and phone going in this idiotic loops.
Still nothing
Yeah, its all okey
Click to expand...
Click to collapse
Can you tell me how did you bricked your phone?[/QUOTE]
I can't :laugh:
Its not my phone, I got a freebie. Guy, who gave me this phone say, what his girlfriend dropped and LCD is damaged, that's all.
Phone not powering up
Phone not powering up
My phone Sony Xperia SP went dead after flashing the kernal mentioned in http://forum.xda-developers.com/show...697865&page=36
Not showing any activity.
Now phone is not powering on ..
I was having a unlocked bootloader + root + cm11
I flashed the new kernal using Flash tool.
Can anyone please help me.
This issue is resolved.
Please find the solution here
sanusunnyk said:
Phone not powering up
My phone Sony Xperia SP went dead after flashing the kernal mentioned in http://forum.xda-developers.com/show...697865&page=36
Not showing any activity.
Now phone is not powering on ..
I was having a unlocked bootloader + root + cm11
I flashed the new kernal using Flash tool.
Can anyone please help me.
Click to expand...
Click to collapse
Flash stock ftf via flashtool
rdlegy said:
Flash stock ftf via flashtool
Click to expand...
Click to collapse
His phone has already working normally. He should edit the question when he succeeded with his phone though.

Hardd Bricked Xperia Z1 Honami

I INstalled a custom rom with Unlocked bootloader and after it was finished it just stuck in black screen... nothing happens the only thing happens is when i press power button and volume up vibrates and then nothing... no led's no charging nothing... please help
Is it detected with Flashtool?
@lexykon : i think since ur device responds, its not a total hardbrick. Flashing an FTF using flashtool should help
sm.vassallo said:
Is it detected with Flashtool?
Click to expand...
Click to collapse
no it says no device connected
You have to push Hard reset button (red button just near the SIM card) until phone vibrates 3 times. Then you push volume down button and then connect PC microUSB cable into the correct connector on your Z1.
Flashtool should see your phone. Then you can flash with flashtool back to your previous (stock ?) ROM.
Azerty728 said:
You have to push Hard reset button (red button just near the SIM card) until phone vibrates 3 times. Then you push volume down button and then connect PC microUSB cable into the correct connector on your Z1.
Flashtool should see your phone. Then you can flash with flashtool back to your previous (stock ?) ROM.
Click to expand...
Click to collapse
I did that but nothing happened it sees the phone but it says Device connected with USB DEBUGGING OFF :/
lexykon said:
I did that but nothing happened it sees the phone but it says Device connected with USB DEBUGGING OFF :/
Click to expand...
Click to collapse
Strange. Did you connect the usb cable to your phone AND maintain volume down button?
Because USB debugging OFF is only when your phone has started Android. When in Flashmode Android is not started.
So after pushing red hard power off button and phone vibrates 3times (it's important it vibrates 3 times) :
- close and restart Flashtool on your computer,
- choose Flash button (strike icon), choose the FTF of the stock firmware then validate and then check 'Flashmode' then OK, it will work few seconds and bring you a new screen explaining you how to get into flash mode with a phone and cable in a Window,
- take your USB cable in left hand,
- push down volume button with your right hand
- connect your cable in micro USB port AND maintain volume down for a few seconds
I decomposed the steps because it is important not to wait too long when connecting cable onto your device and launching Flashtool (that's why I prefer to launch it before, as described above), because if the phone detects current in its usb port, it starts system. It is important to be ready and having Flashtool launched BEFORE plugging the cable.
Send the results.
Azerty728 said:
Strange. Did you connect the usb cable to your phone AND maintain volume down button?
Because USB debugging OFF is only when your phone has started Android. When in Flashmode Android is not started.
So after pushing red hard power off button and phone vibrates 3times (it's important it vibrates 3 times) :
- close and restart Flashtool on your computer,
- choose Flash button (strike icon), choose the FTF of the stock firmware then validate and then check 'Flashmode' then OK, it will work few seconds and bring you a new screen explaining you how to get into flash mode with a phone and cable in a Window,
- take your USB cable in left hand,
- push down volume button with your right hand
- connect your cable in micro USB port AND maintain volume down for a few seconds
I decomposed the steps because it is important not to wait too long when connecting cable onto your device and launching Flashtool (that's why I prefer to launch it before, as described above), because if the phone detects current in its usb port, it starts system. It is important to be ready and having Flashtool launched BEFORE plugging the cable.
Send the results.
Click to expand...
Click to collapse
I followed step by step your guide when i push the volume down and connect it to my pc my phone's led is red and after 1-2 seconds turns off and nothing happens... and if i let it connected to my pc it says device with usb dubugging off is connected :/
lexykon said:
I followed step by step your guide when i push the volume down and connect it to my pc my phone's led is red and after 1-2 seconds turns off and nothing happens... and if i let it connected to my pc it says device with usb dubugging off is connected :/
Click to expand...
Click to collapse
That's quite wierd. The fact that phone's LED becomes red is a good sign, i.e. going to flashmode.
IS it Flashtool saying the phone is in USB debugging ? If not, you can then flash after the LED ran red with flashtool.
Flashtool may say it's USB debugging OFF if Android is booted.
If in flashmode, Flashtool should say :
03/043/2015 15:43:18 - INFO - Device connected in flash mode
And then you can flash...
Azerty728 said:
That's quite wierd. The fact that phone's LED becomes red is a good sign, i.e. going to flashmode.
IS it Flashtool saying the phone is in USB debugging ? If not, you can then flash after the LED ran red with flashtool.
Flashtool may say it's USB debugging OFF if Android is booted.
If in flashmode, Flashtool should say :
03/043/2015 15:43:18 - INFO - Device connected in flash mode
And then you can flash...
Click to expand...
Click to collapse
Thats my flashtool ;/
Have you tried fastboot? Volume up while plugging cable.
Perhaps you can flash a boot.img from there and use recovery at least.
This is what happens to my phone when the kernel fails to flash, usually after restoring a nandroid.
lexykon said:
Thats my flashtool ;/
Click to expand...
Click to collapse
Ok you shouldn't have that in your flashtool log.
Without the phone connected to the PC, you should have the following message, especially "Please connect your device into flashmode" :
03/049/2015 16:49:48 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.4.A.0.108. Customization : Generic FR 1276-5833_R5C
03/049/2015 16:49:48 - INFO - Preparing files for flashing
03/050/2015 16:50:49 - INFO - Please connect your device into flashmode.
From my point of view, it doesn't seem your phone is powered off.
Then to Power Off hard press the red button near sim card, just above the chrome power button until phone vibrates 3 times :
(extract from the "basics" thread of the following post by the excellent DooMLoRD : http://forum.xda-developers.com/showthread.php?t=2440565).
Then do the steps I gave you before.
Azerty728 said:
Ok you shouldn't have that in your flashtool log.
Without the phone connected to the PC, you should have the following message, especially "Please connect your device into flashmode" :
03/049/2015 16:49:48 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.4.A.0.108. Customization : Generic FR 1276-5833_R5C
03/049/2015 16:49:48 - INFO - Preparing files for flashing
03/050/2015 16:50:49 - INFO - Please connect your device into flashmode.
From my point of view, it doesn't seem your phone is powered off.
Then to Power Off hard press the red button near sim card, just above the chrome power button until phone vibrates 3 times :
(extract from the "basics" thread of the following post by the excellent DooMLoRD : http://forum.xda-developers.com/showthread.php?t=2440565).
Then do the steps I gave you before.
Click to expand...
Click to collapse
yes i did all of that and the only thing happens is that log at flashtool and my phone has a red LED and after 2 secs it turns off
lexykon said:
yes i did all of that and the only thing happens is that log at flashtool and my phone has a red LED and after 2 secs it turns off
Click to expand...
Click to collapse
Ok dude. Sorry but I can't help you anymore. Maybe advanced developpers could. My knowledge on flashing Z1 is 2 days old only
FYI, my LED is blinking 1 time red and 1 time green very quickly when I power on my Z1 in flashmode. Nothing on screen, but Flashtool detects my device in Flashmode.
Maybe, as proposed by markuz85, you should try Fastboot mode (volume up instead of volume down)... but I never tried this and I won't be helpful on that.
Good luck and tell us if you have got something.
Azerty728 said:
Ok dude. Sorry but I can't help you anymore. Maybe advanced developpers could. My knowledge on flashing Z1 is 2 days old only
FYI, my LED is blinking 1 time red and 1 time green very quickly when I power on my Z1 in flashmode. Nothing on screen, but Flashtool detects my device in Flashmode.
Maybe, as proposed by markuz85, you should try Fastboot mode (volume up instead of volume down)... but I never tried this and I won't be helpful on that.
Good luck and tell us if you have got something.
Click to expand...
Click to collapse
I went to Sony and played stupid... so they will replace it with my warranty thanks btw guys really appreaciate your help
When I look at your screenshot I think "have you pressed the left button at the flashtool before you connect the device?" only after that you can select the flashmode at this tool.

Failed atempt at entering Fastboot

Hello guys. I've recently got a Z3C and I wanted to flash a custom recovery on it so I can install another rom. I've unlocked my bootloader, no issues there, but when I powered down my phone and pressed volume up and connected it to the pc, it started installing some drivers and power went out. Now my phone is pretty much dead, I can't get into fastboot, nor flashmode. I reinstalled pc companion and the Z3C drivers from flashtool but nothing happens. When I connect my phone, in device manager this is all I get " Qualcomm HS-USB QDLoader 9008"
Is there anything I can do with it? Or is it just a pretty looking paperweight now?
Did you follow this guide to backup your DRM keys first?: http://forum.xda-developers.com/z3-compact/general/how-to-root-backup-drm-keys-t3013343
I would try pushing power button + Volume up + Volume up for 2 seconds and then hold down volume down button only. While you hold it connect your USB cable to the PC and see if flashtool can do something (prepare flashtool first).
Do you remember if your battery was maybe very low? Maybe letting it charge for 10 minutes would help.

My Z2 Pro dead .. help me ..!!

i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second
aljthab said:
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second[/QUOTE try connecting it to the PC, if it doesn't show anything on PC then just hand it over to the lenovo service center and blame it on the device that it stopped booting :silly:. I thought i had bricked my device but they did something and gave it to me in 3 to 4 days and that was done under the warranty no extra charge and don't confess that I had rooted ur device , If u tell them that they will try to extort money from u :crying:
Click to expand...
Click to collapse
aljthab said:
i did something Stupid and my Z2 Pro dead
e LED there is flash yellow for 0.1 second
Click to expand...
Click to collapse
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
kerei said:
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
Click to expand...
Click to collapse
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
same issue with zuk z2
adriano1593 said:
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
Click to expand...
Click to collapse
Hello there... Any solution you found? I am stuck with my zuk z2 in same situation ?? any help ?
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
eryenakgun said:
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
Click to expand...
Click to collapse
Hi,
Thanks for your quick response.
The Hardware ID: USB\DEVICE_DESCRIPTOR_FAILURE
"Error Message": This device has been stopped because it has reported errors. (Code 43)
An error occurred while requesting the USB device descriptor.
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
OtakuLi said:
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
Click to expand...
Click to collapse
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
m_atze said:
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
Click to expand...
Click to collapse
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
OtakuLi said:
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
Click to expand...
Click to collapse
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I don't want to destroy my PC (3000 bugs)
m_atze said:
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I won't destroy my PC (3000 bugs)
Click to expand...
Click to collapse
oh well, good luck
OtakuLi said:
oh well, good luck
Click to expand...
Click to collapse
I will report the result.
OK. I made the deepflash cable.
After using it there is no difference between pressing one of the button combinations I recently mentioned (VOL+ or VOL- or PWR).
The phone will be detected as Unknown device. After intalling my modified driver to match the unknown ID, QFIL don't detect the COM Port.
Hello had the same problem, only with the difference that my battery was not completely discharged.
What has helped:
1 Start QFIL Tool
2 Press the volume +
3 Connect the original cable to the PC
4 QFIL Tool recognized the phone and I could play an original Rome.
Mfg
Ps. Is now the battery cover (glass) broken?
No, I used a hairdryer, a razorblade, plastic tool and a suction cup to lift the backcover glass.
The glass is fully intact no damages.
You have good nerves. I would not have expected that.
But in the end, it does not matter if it does not start anymore.
Thank you again for your great instructions for playing and rooting the mobile phone.
I hope you get your phone back.
Mfg
Good and bad news
The guy unbricked the phone successfully, I received it today.
Now I have an other problem:
The phone is very very slow and laggy now.
The problem occurs everywere, Recovery, boot (the bootlogo laggs), booted System, also the test mode laggs now
Furthermore the sceen flickers sometimes and at the right side the sceen is mirrored sometimes.
Did anyone has an idea?
What I did today:
reflash through qfil
1.9.104_ST
2.3.044_ST
ZUI_2.5.335_ST
Hi m_atze, I am exactly in the same situation as You. After using deep flash cable method, I got "unknown usb device (device descriptor request failed)". Could You tell me what was the solution to unbrick the phone?

Categories

Resources