Failed atempt at entering Fastboot - Xperia Z3 Compact Q&A, Help & Troubleshooting

Hello guys. I've recently got a Z3C and I wanted to flash a custom recovery on it so I can install another rom. I've unlocked my bootloader, no issues there, but when I powered down my phone and pressed volume up and connected it to the pc, it started installing some drivers and power went out. Now my phone is pretty much dead, I can't get into fastboot, nor flashmode. I reinstalled pc companion and the Z3C drivers from flashtool but nothing happens. When I connect my phone, in device manager this is all I get " Qualcomm HS-USB QDLoader 9008"
Is there anything I can do with it? Or is it just a pretty looking paperweight now?

Did you follow this guide to backup your DRM keys first?: http://forum.xda-developers.com/z3-compact/general/how-to-root-backup-drm-keys-t3013343
I would try pushing power button + Volume up + Volume up for 2 seconds and then hold down volume down button only. While you hold it connect your USB cable to the PC and see if flashtool can do something (prepare flashtool first).
Do you remember if your battery was maybe very low? Maybe letting it charge for 10 minutes would help.

Related

[Q] Xperia T LT30at is stuck at Sony screen.[SOLVED]

The problem.
When I boot the device it just stays at the Sony screen and does not progress any further. I am still able to turn off the device by holding the power button and the volume up button, I can reset it by holding the button longer waiting for the vibration, and I can hard reset by waiting till the three vibrations.
What I was doing up to the point it happened.
I was trying to get a custom ROM on my device, I had it previously rooted so I thought I would go further. I installed CWM on my phone I wiped data, cache, and dalvick then I went to install the ROM from SD card. During the attempt at installation I got some symlink errors with a status of 7. Not sure what to do turned off the device when I decided to put back its previous I turned it back on and arrived at the problem.
What I have done to try and fix it.
I have done the soft and hard resets, I tried using the PC companions repair tool. When it asks me to turn the device off hold down the power button then plug in the device nothing happens(I have tried this several times.) I downloaded the flashtool and the correct ftf and tried using that, but it doesn't detect my device when I hold down the volume button and plug it in. So it seems that the flashboot is not working on my phone.
Any suggestions on what to try would be much appreciated and thanks in advanced.
tabersays said:
The problem.
When I boot the device it just stays at the Sony screen and does not progress any further. I am still able to turn off the device by holding the power button and the volume up button, I can reset it by holding the button longer waiting for the vibration, and I can hard reset by waiting till the three vibrations.
What I was doing up to the point it happened.
I was trying to get a custom ROM on my device, I had it previously rooted so I thought I would go further. I installed CWM on my phone I wiped data, cache, and dalvick then I went to install the ROM from SD card. During the attempt at installation I got some symlink errors with a status of 7. Not sure what to do turned off the device when I decided to put back its previous I turned it back on and arrived at the problem.
What I have done to try and fix it.
I have done the soft and hard resets, I tried using the PC companions repair tool. When it asks me to turn the device off hold down the power button then plug in the device nothing happens(I have tried this several times.) I downloaded the flashtool and the correct ftf and tried using that, but it doesn't detect my device when I hold down the volume button and plug it in. So it seems that the flashboot is not working on my phone.
Any suggestions on what to try would be much appreciated and thanks in advanced.
Click to expand...
Click to collapse
You probably didn't install the ADB drivers. Install them from the Flashtool folder (use the ones for TX) and then try flashing your stock FTF again. Remember to put the device into Flashmode.
Basically what happened was that while flashing your ROM the script that flashes everything deletes everything from the /system partition, then you got an error and the installation was incomplete, therefore there is no proper system to boot into. You could have easily avoided what happened by flashing a different ROM had you not powered off.
Antiga Prime said:
You probably didn't install the ADB drivers. Install them from the Flashtool folder (use the ones for TX) and then try flashing your stock FTF again. Remember to put the device into Flashmode.
Basically what happened was that while flashing your ROM the script that flashes everything deletes everything from the /system partition, then you got an error and the installation was incomplete, therefore there is no proper system to boot into. You could have easily avoided what happened by flashing a different ROM had you not powered off.
Click to expand...
Click to collapse
Thank you for response, I went and used the Flashtool-driver.exe and installed the Flashmode drivers, Fastboot drivers and the TX drivers. But it does not seem to have changed anything. To enter flash mode on the phone one has to hold down the volume down button while plugging the phone into the usb when it is powered off, right? Flash tool just sits at the instruction animation titled Wait for Flashmode. When I try to enter flashmode I do not get a response from either the program or the phone. Any more suggestions would be welcomed.
Thank you for taking the time to help.
tabersays said:
To enter flash mode on the phone one has to hold down the volume down button while plugging the phone into the usb when it is powered off, right? Flash tool just sits at the instruction animation titled Wait for Flashmode. When I try to enter flashmode I do not get a response from either the program or the phone. Any more suggestions would be welcomed.
Thank you for taking the time to help.
Click to expand...
Click to collapse
Yes, that is how you enter flashmode. Turn off phone, and keep volume down button pressed while you connect the USB cable; the LED light should turn on with a green light. If you're phone is not entering Flashmode, then you might have a faulty USB cable, or there might be problems with your USB ports, either on your computer or your phone (try with different cables/computers).
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.
Antiga Prime said:
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.
Click to expand...
Click to collapse
Yes, it's better to work on Windows 7 or lower....
Antiga Prime said:
Yes, that is how you enter flashmode. Turn off phone, and keep volume down button pressed while you connect the USB cable; the LED light should turn on with a green light. If you're phone is not entering Flashmode, then you might have a faulty USB cable, or there might be problems with your USB ports, either on your computer or your phone (try with different cables/computers).
Also, check your Device Manager (while phone is connected) to make sure the drivers are properly installed. If you have Windows 8, you should have had to turn of Driver Signature Checking in order for the drivers to install properly.
Click to expand...
Click to collapse
Yeah I turned off the Driver signature checking on my computer when I did it. I'll go buy a new cable and try a friends windows 7 computer. Hopefully there is nothing wrong with the USB port in my phone. Thank you for your help I'll let you know how it goes.
Thank you everybody for your support. My phone is now working. After my phones battery died I was able to get it charging, when it had enough energy it booted itself to the Sony screen so I turned it off and grabbed my new micro USB cable and was able to get it into flash mode. Everything is now working great. I wish a special thanks to Antiga Prime for taking the time to help me.

Hardd Bricked Xperia Z1 Honami

I INstalled a custom rom with Unlocked bootloader and after it was finished it just stuck in black screen... nothing happens the only thing happens is when i press power button and volume up vibrates and then nothing... no led's no charging nothing... please help
Is it detected with Flashtool?
@lexykon : i think since ur device responds, its not a total hardbrick. Flashing an FTF using flashtool should help
sm.vassallo said:
Is it detected with Flashtool?
Click to expand...
Click to collapse
no it says no device connected
You have to push Hard reset button (red button just near the SIM card) until phone vibrates 3 times. Then you push volume down button and then connect PC microUSB cable into the correct connector on your Z1.
Flashtool should see your phone. Then you can flash with flashtool back to your previous (stock ?) ROM.
Azerty728 said:
You have to push Hard reset button (red button just near the SIM card) until phone vibrates 3 times. Then you push volume down button and then connect PC microUSB cable into the correct connector on your Z1.
Flashtool should see your phone. Then you can flash with flashtool back to your previous (stock ?) ROM.
Click to expand...
Click to collapse
I did that but nothing happened it sees the phone but it says Device connected with USB DEBUGGING OFF :/
lexykon said:
I did that but nothing happened it sees the phone but it says Device connected with USB DEBUGGING OFF :/
Click to expand...
Click to collapse
Strange. Did you connect the usb cable to your phone AND maintain volume down button?
Because USB debugging OFF is only when your phone has started Android. When in Flashmode Android is not started.
So after pushing red hard power off button and phone vibrates 3times (it's important it vibrates 3 times) :
- close and restart Flashtool on your computer,
- choose Flash button (strike icon), choose the FTF of the stock firmware then validate and then check 'Flashmode' then OK, it will work few seconds and bring you a new screen explaining you how to get into flash mode with a phone and cable in a Window,
- take your USB cable in left hand,
- push down volume button with your right hand
- connect your cable in micro USB port AND maintain volume down for a few seconds
I decomposed the steps because it is important not to wait too long when connecting cable onto your device and launching Flashtool (that's why I prefer to launch it before, as described above), because if the phone detects current in its usb port, it starts system. It is important to be ready and having Flashtool launched BEFORE plugging the cable.
Send the results.
Azerty728 said:
Strange. Did you connect the usb cable to your phone AND maintain volume down button?
Because USB debugging OFF is only when your phone has started Android. When in Flashmode Android is not started.
So after pushing red hard power off button and phone vibrates 3times (it's important it vibrates 3 times) :
- close and restart Flashtool on your computer,
- choose Flash button (strike icon), choose the FTF of the stock firmware then validate and then check 'Flashmode' then OK, it will work few seconds and bring you a new screen explaining you how to get into flash mode with a phone and cable in a Window,
- take your USB cable in left hand,
- push down volume button with your right hand
- connect your cable in micro USB port AND maintain volume down for a few seconds
I decomposed the steps because it is important not to wait too long when connecting cable onto your device and launching Flashtool (that's why I prefer to launch it before, as described above), because if the phone detects current in its usb port, it starts system. It is important to be ready and having Flashtool launched BEFORE plugging the cable.
Send the results.
Click to expand...
Click to collapse
I followed step by step your guide when i push the volume down and connect it to my pc my phone's led is red and after 1-2 seconds turns off and nothing happens... and if i let it connected to my pc it says device with usb dubugging off is connected :/
lexykon said:
I followed step by step your guide when i push the volume down and connect it to my pc my phone's led is red and after 1-2 seconds turns off and nothing happens... and if i let it connected to my pc it says device with usb dubugging off is connected :/
Click to expand...
Click to collapse
That's quite wierd. The fact that phone's LED becomes red is a good sign, i.e. going to flashmode.
IS it Flashtool saying the phone is in USB debugging ? If not, you can then flash after the LED ran red with flashtool.
Flashtool may say it's USB debugging OFF if Android is booted.
If in flashmode, Flashtool should say :
03/043/2015 15:43:18 - INFO - Device connected in flash mode
And then you can flash...
Azerty728 said:
That's quite wierd. The fact that phone's LED becomes red is a good sign, i.e. going to flashmode.
IS it Flashtool saying the phone is in USB debugging ? If not, you can then flash after the LED ran red with flashtool.
Flashtool may say it's USB debugging OFF if Android is booted.
If in flashmode, Flashtool should say :
03/043/2015 15:43:18 - INFO - Device connected in flash mode
And then you can flash...
Click to expand...
Click to collapse
Thats my flashtool ;/
Have you tried fastboot? Volume up while plugging cable.
Perhaps you can flash a boot.img from there and use recovery at least.
This is what happens to my phone when the kernel fails to flash, usually after restoring a nandroid.
lexykon said:
Thats my flashtool ;/
Click to expand...
Click to collapse
Ok you shouldn't have that in your flashtool log.
Without the phone connected to the PC, you should have the following message, especially "Please connect your device into flashmode" :
03/049/2015 16:49:48 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.4.A.0.108. Customization : Generic FR 1276-5833_R5C
03/049/2015 16:49:48 - INFO - Preparing files for flashing
03/050/2015 16:50:49 - INFO - Please connect your device into flashmode.
From my point of view, it doesn't seem your phone is powered off.
Then to Power Off hard press the red button near sim card, just above the chrome power button until phone vibrates 3 times :
(extract from the "basics" thread of the following post by the excellent DooMLoRD : http://forum.xda-developers.com/showthread.php?t=2440565).
Then do the steps I gave you before.
Azerty728 said:
Ok you shouldn't have that in your flashtool log.
Without the phone connected to the PC, you should have the following message, especially "Please connect your device into flashmode" :
03/049/2015 16:49:48 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.4.A.0.108. Customization : Generic FR 1276-5833_R5C
03/049/2015 16:49:48 - INFO - Preparing files for flashing
03/050/2015 16:50:49 - INFO - Please connect your device into flashmode.
From my point of view, it doesn't seem your phone is powered off.
Then to Power Off hard press the red button near sim card, just above the chrome power button until phone vibrates 3 times :
(extract from the "basics" thread of the following post by the excellent DooMLoRD : http://forum.xda-developers.com/showthread.php?t=2440565).
Then do the steps I gave you before.
Click to expand...
Click to collapse
yes i did all of that and the only thing happens is that log at flashtool and my phone has a red LED and after 2 secs it turns off
lexykon said:
yes i did all of that and the only thing happens is that log at flashtool and my phone has a red LED and after 2 secs it turns off
Click to expand...
Click to collapse
Ok dude. Sorry but I can't help you anymore. Maybe advanced developpers could. My knowledge on flashing Z1 is 2 days old only
FYI, my LED is blinking 1 time red and 1 time green very quickly when I power on my Z1 in flashmode. Nothing on screen, but Flashtool detects my device in Flashmode.
Maybe, as proposed by markuz85, you should try Fastboot mode (volume up instead of volume down)... but I never tried this and I won't be helpful on that.
Good luck and tell us if you have got something.
Azerty728 said:
Ok dude. Sorry but I can't help you anymore. Maybe advanced developpers could. My knowledge on flashing Z1 is 2 days old only
FYI, my LED is blinking 1 time red and 1 time green very quickly when I power on my Z1 in flashmode. Nothing on screen, but Flashtool detects my device in Flashmode.
Maybe, as proposed by markuz85, you should try Fastboot mode (volume up instead of volume down)... but I never tried this and I won't be helpful on that.
Good luck and tell us if you have got something.
Click to expand...
Click to collapse
I went to Sony and played stupid... so they will replace it with my warranty thanks btw guys really appreaciate your help
When I look at your screenshot I think "have you pressed the left button at the flashtool before you connect the device?" only after that you can select the flashmode at this tool.

Sony Z3+ E6553 Dead After Flashing with FlashTool

I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
citifone said:
I used FlashTool to flash Sony Z3+ E6553 and now phone cannot power on at all. When I plug in to PC, PC can detect but flashtool cannot flash anymore. The phone was working fine, only has phone lock. Please help revise the phone. Thanks.
Click to expand...
Click to collapse
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Allek84 said:
Are you sure that your battery is charged?
Try this: press and hold power and volume up button for 10 seconds and see does the phone vibrate.If vibrate flash again via flashtool.,he should works.
Click to expand...
Click to collapse
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
citifone said:
Battery was fully charged and I've tried that but phone does not response at all to flashtool. When plug in to PC, in device manager under USB controllers, it sees it as SOMC Flash Drive. I think the phone boot is dead.
Click to expand...
Click to collapse
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Allek84 said:
Listen,start flashtool again and hit flash and when pop up windows show press and hold volume down button and connect phone to cable.It should to install so called s1 boot driver(SEMC flash device)Do like I said and see what happends when you connect phone to cable.
If pc install any driver start flashtool again and try to flash again.
Before everything,try to press and hold power and volume up buttoins for more time,about 15 seconds and see did he vibrate.
Click to expand...
Click to collapse
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
somc flash device means dead boot....its no solution yet for it,sorry
this guy or website promise to repair this dead boot problem via test point look here:
ht_tp://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
or here
http://www.vungoc-mobile.com/index.php/unlock/932-repair-boot-unbrick-sony-e6553-xperia-z3
citifone said:
Thanks for your help...The phone was flashed successfully with flash tool with flash file E6553_28.0.A.4.8. After flash done, phone was dead, cannot power on anymore. Now when I tried to flash it again, volume down, insert USB the flashtool show as: Device detected with USB debugging off. It doesn't go to flash mode anymore. I took the back cover off, remove battery connector flex cable and connect it back and try flashing many times but flashtool will not detect phone in flash mode..PC can detect phone because it makes connecting sound on PC but detects as what mode I don't know. In device manager, it doesn't show any device in com port but it shows SOMC Flash Device in USB controllers. I tried to press volume up + power but nothing happened. Once again thanks for your help.
Click to expand...
Click to collapse
As I understood, you tried to downgrade. Am I right? I heard that sometimes downgrading causes hard brick. I don't know how to fix it but only option is bringing service.
sone xperia z3+ (E6553) flash after dead
sone xperia z3+ (E6553) flash after dead
sony xperia z3+ e6553 model
flash with this model e6653
it does not start after with it
please help me sir

Help on xperiz z1: dead during update.

Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
sunil14353 said:
Hi Guys,
I had a battery draining problem. During the firmware update, device got dead in process of the update.
Battery charge was above 90% during the update.
After replacement of battery. Tired by holding power+vol up & holing vol down. Device is not recognized.
I am trying to install stock ROM. Below are the steps which I have performed so far.
1. Charged the device for overnight (Red LED blinking) & when connected to charger (LED=RED, stable)
2. Installed flash tool, drivers
3. When prompted to connect the device for flashing, i get the below info. For which I tired with different flash-tool versions.
23/051/2016 15:51:13 - INFO - Device connected with USB debugging off
23/051/2016 15:51:13 - INFO - For 2011 devices line, be sure you are not in MTP mode
4. Tired to repair from Sony PC companion suite as well by pressing "volume down button". Device is not recognized when prompted.
Could anyone pls help me on this.
Regards
Sunil
Click to expand...
Click to collapse
hi
are you ready to disassemble your xperia?
did you try this ???
look here
http://sony.yt/topic/7324-english-t...oot-in-sony-xperia-z-c6602-c6603-c6606-c6616/
sorry to put a link from another forum.
Hey i'm not exactly sure what you mean by the description, but to enter flash mode you need to turn off the device - then hold down the volume-down key whilst inserting the usb. Keep holding down the volume-down key until you seen some green notification lights flash and you should be in flashmode and ready to flash a FTF. It should also say on flashtool that "Device has entered flashmode" or something like that.

My Z2 Pro dead .. help me ..!!

i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second
aljthab said:
i did something Stupid and my Z2 Pro dead
there is no fast-boot and no recovery .. only black screen and when i press power button there is a short and long vibration just that and the LED there is flash yellow for 0.1 second[/QUOTE try connecting it to the PC, if it doesn't show anything on PC then just hand it over to the lenovo service center and blame it on the device that it stopped booting :silly:. I thought i had bricked my device but they did something and gave it to me in 3 to 4 days and that was done under the warranty no extra charge and don't confess that I had rooted ur device , If u tell them that they will try to extort money from u :crying:
Click to expand...
Click to collapse
aljthab said:
i did something Stupid and my Z2 Pro dead
e LED there is flash yellow for 0.1 second
Click to expand...
Click to collapse
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
kerei said:
I have exactly the same, what to do? I installed the dev 44, the rate of established but after 15 minutes, logo is stalled, not waiting until the end of excess freewheeling dev 300, it is not fully established and bug crawled, I rebooted the machine and an endless vibration with green LED :crying:
1 Charging can be a little warm
2. can not be detected pc
3. can not access the fastboot mode
4. when charging, the notification light dies
5. deep flash cable has not helped
sorry my bad english
Click to expand...
Click to collapse
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
same issue with zuk z2
adriano1593 said:
Refer to this http://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ and this http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-z2131-only.104/
Click to expand...
Click to collapse
Hello there... Any solution you found? I am stuck with my zuk z2 in same situation ?? any help ?
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
eryenakgun said:
What id shown in unknown device.
Like ven_9102&dev_1234
Maybe with editing quallcom drivers for your device id, you can still install it.
and if luck qpst can recognize it as qualcomm debug mod
Sent from my ZUK Z2121 using Tapatalk
Click to expand...
Click to collapse
Hi,
Thanks for your quick response.
The Hardware ID: USB\DEVICE_DESCRIPTOR_FAILURE
"Error Message": This device has been stopped because it has reported errors. (Code 43)
An error occurred while requesting the USB device descriptor.
m_atze said:
I have a similar problem.
What caused the black screen? -
History:
I booted to test mode at 2.5.033 ST, the phone got stucked at this menue there was no way to get out. TWRP Restore to Nandroid bougt only black screen after 2nd vibration and ZUK logo.
I fixed the Test mode bug, by flashing the ZUI 1.9.104 ST Stock ROM via QPST.
After the phone was "repaired" I unlocked the bootloader, installed TWRP, made a nandroid backup of fully stock ROM and restored a nandroid backup from before the test mode problem.
The nandroid restore was successful, I rebooted the phone and it was "dead". Black screen, only rebooting (perioldy vibrating) there was no end, until the battery was empty.
I got no luck to reach any mode with tricky button pressing (vol+ pwr; vol- pwr; vol+ vol- pwr; usb in vol-) nor Windows detecting the phone. That's why I decided to remove the back glass cover, to got access to the battery.
Now I'm able to get the phone detected by my PC.
What I did: disconnect the battery, connect the phone to my computer, pressed the vol- button and connect the battery.
This made my PC able to detect the phone, but no I have an other problem. Windows only detects the phone as "unknown usb device (device descriptor request failed)". I don't know any way to install the driver....
Maybe anyone is able to help me or has any tip?
Thanks!
Cheers,
m_atze
Click to expand...
Click to collapse
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
OtakuLi said:
Alright bro, there is one method you can try.
http://zukfans.eu/community/threads/howto-flash-a-stock-zui-rom-zuk-z2-pro-z2121-only.57/
I assume your phone is a brick now. The only method you can use is the 9008 unbrick mode. (AKA QBST)
There are a few things you need to prepare before you save ur phone. U need to download the require application that the website provided above, after you set everything up,
make sure you download the latest 2.5 QBST rom,
http://bbs.lenovomobile.cn/z2pro/t554654/
Because ur phone wont be able to enter 9008 through software, thus u need to do the following.
1. Load the content XML fille,
2.Turn off your phone. After it's fully shutdown
3. press and hold the volume up button for 3 seconds
4. press power button while hold the volume up (press it for 0.5second and keep holding it)
5. after 0.5 seconds, plug in the usb right away
6. the QFIL tool should appear the Qualcomm usb QD loader
7. the download button should turn blue
8. flash it and wait for reboot
Click to expand...
Click to collapse
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
m_atze said:
Thanks for your tip.
I followed your described procedure, but the phone will not be recocnized by the PC.
1st: I loaded QFIL XML file. (By the way this tut is made by me)
2nd: I disconnected the battery (The phone can't be turned off normally!)
3rd, 4th, 5th
6th: nothing happend!
7th: "-"
8th: "-"
The only way the phone will detected by the PC:
1st: disconnect battery
2nd: plug in USB (PC and Phone)
3rd: press VOL+ or VOL- or PWR button (doesn't matter which one)
4th: connect battery
5th: detected as "unknown usb device (device descriptor request failed)"
Click to expand...
Click to collapse
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
OtakuLi said:
Make sure you have to plug in the usb right away as soon as you u press power, and keep holding them
Click to expand...
Click to collapse
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I don't want to destroy my PC (3000 bugs)
m_atze said:
Yes, I did exactly you described. Sorry but this isn't working.
I don't know what I should do. Even a repair shop couldn't fix it.
Maybe I need to do this:
http://bbs.lenovomobile.cn/z2/t121791/?highlight=900e
But I won't destroy my PC (3000 bugs)
Click to expand...
Click to collapse
oh well, good luck
OtakuLi said:
oh well, good luck
Click to expand...
Click to collapse
I will report the result.
OK. I made the deepflash cable.
After using it there is no difference between pressing one of the button combinations I recently mentioned (VOL+ or VOL- or PWR).
The phone will be detected as Unknown device. After intalling my modified driver to match the unknown ID, QFIL don't detect the COM Port.
Hello had the same problem, only with the difference that my battery was not completely discharged.
What has helped:
1 Start QFIL Tool
2 Press the volume +
3 Connect the original cable to the PC
4 QFIL Tool recognized the phone and I could play an original Rome.
Mfg
Ps. Is now the battery cover (glass) broken?
No, I used a hairdryer, a razorblade, plastic tool and a suction cup to lift the backcover glass.
The glass is fully intact no damages.
You have good nerves. I would not have expected that.
But in the end, it does not matter if it does not start anymore.
Thank you again for your great instructions for playing and rooting the mobile phone.
I hope you get your phone back.
Mfg
Good and bad news
The guy unbricked the phone successfully, I received it today.
Now I have an other problem:
The phone is very very slow and laggy now.
The problem occurs everywere, Recovery, boot (the bootlogo laggs), booted System, also the test mode laggs now
Furthermore the sceen flickers sometimes and at the right side the sceen is mirrored sometimes.
Did anyone has an idea?
What I did today:
reflash through qfil
1.9.104_ST
2.3.044_ST
ZUI_2.5.335_ST
Hi m_atze, I am exactly in the same situation as You. After using deep flash cable method, I got "unknown usb device (device descriptor request failed)". Could You tell me what was the solution to unbrick the phone?

Categories

Resources