Good morning,
So, my Moto X woke me up this morning by vibrating every few seconds on my nightstand. Evidently, the device was stuck in a bootloop, where it'd just get to the charging screen, and then reboot.
Turns out the outlet that the powerstrip that my phone was plugged into started "flickering" at some point last night... it'll give power for a quick second, then stop, and flip between those two states very rapidly.
Two questions... because I don't know much about batteries.
1. Do you think that caused any damage to my phone's battery? I've plugged it into a different outlet, now... and it appears to be charging fine.
2. Any idea what causes a power outlet to just start "flickering" like that? (I have verified that it's not the power strip's fault, nor the Motorola phone charger's fault).
Thanks so much.
Spirotot said:
Good morning,
So, my Moto X woke me up this morning by vibrating every few seconds on my nightstand. Evidently, the device was stuck in a bootloop, where it'd just get to the charging screen, and then reboot.
Turns out the outlet that the powerstrip that my phone was plugged into started "flickering" at some point last night... it'll give power for a quick second, then stop, and flip between those two states very rapidly.
Two questions... because I don't know much about batteries.
1. Do you think that caused any damage to my phone's battery? I've plugged it into a different outlet, now... and it appears to be charging fine.
2. Any idea what causes a power outlet to just start "flickering" like that? (I have verified that it's not the power strip's fault, nor the Motorola phone charger's fault).
Thanks so much.
Click to expand...
Click to collapse
Is it a surge protector or just a standard power strip..2ndly how old is it? And r u using the USB charger it came with or older one?
Slapped my Moto
If it's happening in other outlets it could be an issue with the main line to the location.
If it is only happening at that one outlet, you potentially have a fire hazard. It could be a short, or it could just be that outlet doesn't allow for a plug to consistently connect. Either way, I'd recommend replacing the outlet immediately. Until that's done flip the breaker or remove the fuse associated with the outlet. While replacing an outlet is something you can do yourself, this probably isn't the place for a tutorial. If even after replacing the outlet, you still have issues, get an electrician involved.
I'd be surprised if it caused damage to your battery. These batteries have circuitry to prevent that.
Related
hi, new member here.
bought my tilt on 10/4/07. has been flawless since that time.
used the nav quite a bit during a road trip, used a cig lighter usb charger.
got home and my battery was at roughly 40%.
put it on the charger at night went to sleep. in morning disconnected it at 8 am. shortly after i arrived at work i got the critical battery low chime. checked and it had like 7% battery life.
figured i didnt plug it in right, or it got knocked loose some how and didnt get charged.
put it in flight mode to minimize battery usage. left work at 2 30 pm (4% battery life) and put it on the car charger. got home and put it on the HTC supplied wall charger. light turned amber, so i assumed it was charging.
checked an hour later and turned phone on, it said 0%, and immediately died. left it on the charger for a few hours and the light was still amber, turned it back on and again 0% and phone immediately died and did a soft reset on its own. i turned the phone off and left it on the ac charger, took out the sim card and put it in an old blackberry to use while the battery was charging.
its been on the ac wall charger for the last several hours, i checked and the phone is totally dead, cannot turn it on, and the LED at the top is now RED.
what is the problem here? why wont this thing charge?
thanks in advance, i have alot of critical info on this device and any help would be greatly appreciated.
i cannot hard reset because i cannot turn the flippign thing on....
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
I'd try a different charger first. If that makes no difference then a different battery. If that still does not make any difference then time to exchange it.
Lidberg said:
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
Click to expand...
Click to collapse
connected to either the computer or the wall charger, the LED thats normally amber when charging, and green when charged, remains red.
I had something very similar happen to my wizard.
And as weird as it sounds, the only fix was to charge the battery in a friends wizard on his charger. I'd check the battery if possible.
Could be the battery. Know any place or anyone that will let you try a charged battery? If not, you might have to go in to an AT&T store.
i think i got it working. did some reading/browsing...
took a usb wire and cut the mini usb head off. dissected it and found the the red and black charging wires. took out the battery and held the leads to teh battery while the other end was plugged into a USB/AC adapter wall charger from a old blackberry. after manually charging the battery for several minutes, i put the battery back in the phone and the phone started up. now it seems to be charging off the wall charger and the led is now amber from red.
thanks for all your help/suggestions.
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
tiltyoself said:
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
Click to expand...
Click to collapse
Repeat this proceedure but this time do not turn the phone on, just plug it in to the wall charger once you have zapped the battery again.
Turning your phone on probably just caused the already recovering battery to die whiles it is trying to take on a charge.
It is mentioned quite a lot on the boards that Li-Ion Batteries do not like being over disscharged and there is usually a little protection circuit in the battery to provent complete disscharging although this circuit may be on board the phone. Completely disscharging a Li-Ion cell will kill it stone dead and it will need replacing.
When you took the battery out and so called jump started it with your flying leads, this possibly reset the little protection circuit in the battery so it can now take on a charge. I feel that once you turned on the phone, this was to much for the already depleted cell to take and possibly re-tripped its inbuilt circuit.
If you do manage to recover you cell, in future it is good practice not to let the battery go below about 25%. Li-ion cells are generally happy being top off regularly.
I hope this helps buddy
Do let us know!
Cheers
C.
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
That Sucks! I hope they'll give you a new battery.
tiltyoself said:
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
Click to expand...
Click to collapse
I had exactly the same problem with my battery. It came on though after a day. Although the battery life after this happened went down to 10hrs max on standby. I sent the phone back and got a new one and now all is fine.
This is a problem that affects almost all makes of phone. There are three (main) causes of the problem:
1.
The battery charge drops too low to allow the charging circuit to recognise a battery is even in place (red no charge light stays lit)
possible solution:
http://forum.xda-developers.com/show...22&postcount=6
(in the end very similar in the end to the USB wire used in post above)
2.
A faulty battery (but if you can charge it using a cut usb cable or using a couple of AA batteries this may not be a faulty battery.
3.
A faulty charger OR a charger not delivering 5v at 1000mA as the OEM one does. Many chargers that are used for other phones or generic chargers only deliver 500mA. This is not enough when your battery drops very low. (these chargers are OK for occasional use but I do not advise using them regularly particularly if the no-charge syndrome has shown itself)
4.
A faulty USB connection on the phone. I have now seen a couple of reports where the fine wire connections in the phones USB port have become bent out of place.
Number 4 above is at least possible for the OP as it seems the battery will charge using a cut USB cable but not when either the PC USB cable or mains charger is connected. A USB port on the phone with a a bent internal contact would explain what's happening.
A previous poster was able with a needle or similar to bend the contact back into place.
Mike
i had the same problem with my phone.
put it in the charger overnight and woke up in the morning and couldnt turn on the phone with blinking red light. I don't know if my battery was over-drained though. I went to AT&T and was playing around with their charger and new battery and somehow the so-called dead battery started working again. They changed the SIM card on my phone there and then i haven't been able to use the phone since. I've changed the network to GSM instead of Auto setting under Phone Options which allows us to make calls; but now I can't connect to 3G network.
Charging thru mini usb
My phone started to exhibit similar problems...plugged in but no charging of the battery. I finally realized that my mini usb connection on the phone has been compromised (bent, distorted=not functioning properly) Now I have to prop the mini usb connection up at a slight angle to engage the charge. I think the plastic/metallic connector on the phone is somewhat fragile ...I had similar issues with my hermes.
called customer support.
they are sending me a new phone and battery.
how do i know its not a refurbished one? any clues?
before u send out your defect phone, have u check if your phone's mini-USB connector has bent or misaligned pins?
yeah all the connectors visually are fine.
Without knowing what it was, I encountered the RLOD on my phone after leaving it on USB overnight. After reading the first two or three pages of two different threads I tried the little lucky "fixes" and found that none of them worked.
I have a backup phone and need my phone for work, so I put my SIM in that phone only to find it was dead. Went to my local AT&T store and they said the SIM is fried. They replaced the SIM and everything is working now.
I replaced the battery in my TyTN and now I'm recharging my original battery. The phone works without problems, or heating up, or shortened battery life.
So here is my theory:
The phone has a similar monitor as the offgrid solar system does. It's job is two-fold: don't let the battery overcharge -and- don't let the battery every discharge to 0.
I suspect that most problems may happen when the phone is connected to a laptop or desktop computer via the USB port and left on when the computer goes to sleep. At this point, the scenario is similar to a monitor on an offgrid solar home. The monitor decides when to pull from the batteries and when to fire up a generator. But if the monitor is set incorrectly, it constantly flicks between charge/generator and the end result is a huge draw on the batteries (rather than a charge going into the battery).
Now with the laptop asleep the trickle charge is way lower than normal. Activity on the phone may also actually flick the laptop in and out of sleep mode. The basic end result is the phone starts the same type of draw between battery and trickle charge, causing a higher than normal draw on batteries, and finally it heats up the chip on the SIM and fries it either partially or completely.
If you have "resuscitated" your phone, but still have problems, simply replacing the SIM should fix it. If you get the RLOD I'd say get the SIM replaced as it is fried. Once you get the SIM and any SDHC card out, very tentatively try to recharge the old battery on the wall charger. (In other words, don't take your hand off the charger when you plug it into the wall) If you get a yellow light, breath easy. If you get the red light, UNPLUG IMMEDIATELY and throw that battery away!
My research on offgrid solar has been going on for almost a year and I began this theory when I noticed a few things:
1) I saw posts from people with not just HTC phones getting a red light.
2) I saw a few posts where people mentioned they used the USB overnight.
3) I have seen firsthand what the constant toggling can do to a 24V 1500 kilowatt hour battery system and the heat it generates.
Except...
There is no USB power when a laptop is shut down except for a few newer models which are designed intentionally to do so. And USB activity does not wake the laptop, particularly not "in and out" of sleep mode. If it does, your laptop has problems.
Final point.. Hasn't it been ground in to use the supplied charger? Most people who report failures admit they were using third-party chargers.
That said, a USB cable should be a more reliable charge source than a cheap AC charger due to the fact that a laptop has to have clean power itself and cheap AC chargers can fail in many fashions and often result in excessive DC voltage or AC voltage winding up in the source.
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
jvillejoe said:
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
Click to expand...
Click to collapse
what are you charging from? are you using the stock nook cable and plug?
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
altimax98 said:
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
Click to expand...
Click to collapse
Yeah seems to me thats what it must be I'll post back what I find out.
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
RobertsDF said:
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
Click to expand...
Click to collapse
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
jvillejoe said:
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
Click to expand...
Click to collapse
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Non-Standard chargers...
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
danger-rat said:
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Click to expand...
Click to collapse
I never used another charger besides the stock charger that came with the NC. Up until this happened all that was ever used was the stock cable for charging. I only used another charging cable once I ran into these problems cause I figured the cable was damaged. Its happened to me before with other devices. But the same results happen with every cord I use. When I plug it in it lights up and shows the red battery screen. So that tells me that the cord or USB port couldn't be the problem. Cause its clearly getting power its just not charging.
Fattychance said:
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
Click to expand...
Click to collapse
When charging I can not turn the screen off it's stuck on the screen with a red battery.
jvillejoe said:
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
Click to expand...
Click to collapse
No. They sell it without one...the 8GB internal storage is enough for looooottts of books. The microsd was just a nice + for people with lots and lots of music.
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
bstock said:
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
Click to expand...
Click to collapse
Thanks for the feed back. I'm wondering by un-pluging the battery from the nook if it resets it. Kind of like if a phone freezes or if your computer freezes and you pull the battery. Seems like a plan. Not sure if this is what I'll do as I'm sure its still under warranty. If it comes back and its not covered or B & N wont replace it I guess thats my only hope.
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
CLMT said:
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
Click to expand...
Click to collapse
If your not worried about voiding the warranty then sure I guess its worth a shot.
So I got it fixed right. All it was was a faulty cable lol!
jvillejoe said:
So I got it fixed right. All it was was a faulty cable lol!
Click to expand...
Click to collapse
I had this problem too, but I'm not sure "faulty" is the right word for the cable.
My friend borrowed my nook and returned it with a dead battery (Thanks asshole). So I plugged it into my computer at work and just got the always-on low battery message. After 45 minutes I took it to my car so I wouldn't forget it. I plugged it into my USB charger in the car using a different cable. Two hours later, same state.
When I got home I pugged it into the Nook wall charger with yet another cable (not the nook's original) and got the same thing. I searched here to see if I could figure out what was going on and decided to try the original cable with the wall plug. literally two seconds after plugging it in it started booting into Froyo.
I'm sure I didn't have four "faulty" cables. I think those that are saying you should be using the original are correct. The others worked fine when the battery wasn't empty, but mine only responded to the original once it got to the point of the unending low-battery message.
Original charger / cable required with totally empty battery
Same here. With battery completely empty and non standard cable,stuck at red battery sign forever. With orginal cable, boots fine and charges.
solution I found
Have CM7 installed on SDCard, got the battery icon, even with the unit plugged into the charger with oem equipment. Held the power button 'til the unit turned off completely, removed the sdcard, rebooted. Nook booted into stock fine, turned off, re-inserted sdcard and rebooted. All is well.
i got zapped by the dreaded broken power button.
ive read up on a lot of soln from app/widget/rooting work around to solve the lock/unlocking. these work great.
but
my phone wont charge the battery any more.
this happened the same time the power button stopped.
the charge light is red not orange.
ive tried a plug in charger, car charger, usb, and my desk charger.
the desk charger saves my butt because i have two batteries and i can charge one while the other one is used by the phone.
so my question is:
is this simply a flex cable replacement fix?
ive read lots about the power button problem but i have not seen any accompanying issues with charging that im experiencing.
Sounds like two unrelated problems. If you fix/replace the power button you would probably only fix that and not the charging. You could check where the short is by backtracking from the plug with a multimeter.
Is the device visible with usb plugged in and doesn't charge? If that's the case you probably just have a short in one of the pins. But if not, that would need to be replaced.
hey EK,
thanks for response.
yes USB connectivity works great. and yes it wont charge while plugged in. When the battery lowers to a certain percent like 90% - i assume thats when the phone starts to charge it and when it begins this charge cycle, the battery light is red instead of orange.
ill give the multimeter a shot. i havent looked but wondering if there are any instructions out there for this check?
HH
The battery won't charge if it is plugged in between 90-100% as that can cause batteries to age quickly.
bassmadrigal said:
The battery won't charge if it is plugged in between 90-100% as that can cause batteries to age quickly.
Click to expand...
Click to collapse
yup, knew that.
an update. both batteries do in fact charge. it just doesn't register as in charging mode for about 5 minutes - weird!
I can live with this. I'll just do a flex cable swap.
thanks
My phones been dead for about a month, most hope was given up but heres my last ditch. I updated to android N preview. Used it like normal. The last day (before my phone ate ****) i was having problems charging it. It wasnt accepting the charge almost as if my "Quickcharge 2.0" had stopped. In fact it would discharge while connected to turbo charger. Anyways that day i went swimming, where i live its very hot i left it on the charger near the pool and it had gotten super hot. So i took it off and put it in a chair and it was on again super hot (hot enough that it burnt my hand when i touched the glass) and it was still on it hadnt shut off. Some people there put it in their cooler for me and that was that, although i noticed a burn mark on the actual usb port on the phone itself. Fast forward a few hours. I was skyping some chick got off skype. Turned my phone off in the hopes it would charge faster. ( it was at 13%) plugged it into the charger, Nothing. Tried to turn it on, Nothing. I finally got it to boot up ( i had to press the **** out of the power button) and the google logo came up. Then it turned off. Tried again to power it on. Same thing, google logo dead. Left it on the wall charger for an hour. tried to power it up, nothing. Used a samsung wireless charger on it for close to 3 hours. Tried to power it up. Still nothing. Power + Vol Down. Nope nada. Opened it up checked the wires everything was plugged in and secure. I didnt make it any further than the backplate because i stripped the screws. Since then its just sat on my shelf, but today i dropped it on my foot and i decieded to see if it would turn on, so i plugged it into my pc (and this is honestly the reason im writing this) and i wiggled the charger around and my pc actually "sensed" it. It said that "The usb device has malfunctioned" so idk what that means. Maybe its still there maybe not. Ik that if i can get my pc to recognize it again it will be difficult as that port on the phone is on its LAST leg.
Let me know what you guys think. Sorry for the short story. Just want to make sure you know everything as it happened
Also when i plug it into the wall, or use the Qi charger on it the device heats up/gets warm. Again dont know if its anything but the more the better.
Could be anything really, possibly a bad battery, if the QI charger isn't helping. How old is the device, and when did the usb burn mark appear?
Okay so I am going to give my best guess here, that the battery in your phone has gone bad, and it was killed by your charger going bad with an electrical short circuit.
Here is my reasons for think that...
Currently your phone won't accept a charge at all, so that leads me to believe that the battery has gone bad.
As for my suspicion that your charger went bad, I have had two different quality brand chargers (HTC and Samsung) go bad on me over the last 3 years or so.
Both times the charger failures caused the same symptoms on my phone that you described...the phone getting extremely hot, and the battery discharging, while connected to the charger, instead of charging.
Luckily for me, in both cases, my phone batteries did not completely croak.
In one case the battery did bulge out the phone, but it was an older HTC M7 and it kept working.
In the other case, I noticed that hot phone and the discharging, and immediately unplugged the charger and tossed it in the trash.
So that is just my two-cents.
KCT1975 said:
Okay so I am going to give my best guess here, that the battery in your phone has gone bad, and it was killed by your charger going bad with an electrical short circuit.
Here is my reasons for think that...
Currently your phone won't accept a charge at all, so that leads me to believe that the battery has gone bad.
As for my suspicion that your charger went bad, I have had two different quality brand chargers (HTC and Samsung) go bad on me over the last 3 years or so.
Both times the charger failures caused the same symptoms on my phone that you described...the phone getting extremely hot, and the battery discharging, while connected to the charger, instead of charging.
Luckily for me, in both cases, my phone batteries did not completely croak.
In one case the battery did bulge out the phone, but it was an older HTC M7 and it kept working.
In the other case, I noticed that hot phone and the discharging, and immediately unplugged the charger and tossed it in the trash.
So that is just my two-cents.
Click to expand...
Click to collapse
What advices do you have to avoid this kind of problem?
Okay guys. I would have to check the IMEI to give you hard facts for the dates. Which I can do im just at work. But last I looked it was manufactured in, March of 2014 or close to that. Ik for a fact that he model was an XT1103 it was completely factory unlocked however my bootloader was locked. Storage was encrypted. And it was the 32gb version. Yes! It could quite possibly be my battery.
Before all this started I was having trouble getting it to charge and I was using a Samsung mini USB with it. But the outlets at the pool I don't think are designed to charge phones. Anyways the burn mark on my USB port showed up the same day. I just didn't notice it (I think) until later that day,but after I got it my phone no longer charged. It would either discharge off the charger, or discharge slower on it.
thetransit123 said:
What advices do you have to avoid this kind of problem?
Click to expand...
Click to collapse
Sorry for the delay in replying...RF got in the way.
Anyways...I really can't offer much 'technical advice'. I can, however, offer some practical advice.
1. Use brand name chargers or be careful if you do use an off-brand charger.
2. If you are charging your phone (either on a brand name charger or an off-brand charger), and you either feel it getting hot or you see it discharging (or both) immediately unplug your phone and throw away the charger.
3. If you do notice that the battery on your phone is bulging, either replace the battery or if it is a sealed device, replace the phone.
Honestly, that is the only advice I can give.
So guys ive decided i m gonna go ahead and try and replace my battery since its rather inexpensive, im gonna order the parts from ifixit. such as anew midframe and battery. It should be done hopefully by next week. Im still completely open to opinions. When its complete ill make a post.
KCT1975 said:
Sorry for the delay in replying...RF got in the way.
Anyways...I really can't offer much 'technical advice'. I can, however, offer some practical advice.
1. Use brand name chargers or be careful if you do use an off-brand charger.
2. If you are charging your phone (either on a brand name charger or an off-brand charger), and you either feel it getting hot or you see it discharging (or both) immediately unplug your phone and throw away the charger.
3. If you do notice that the battery on your phone is bulging, either replace the battery or if it is a sealed device, replace the phone.
Honestly, that is the only advice I can give.
Click to expand...
Click to collapse
In my case, i use aukey quick charge 2.0 and it works great, when i charge the phone, i do it on the night and try to not use when it charge, i dont like to charge with scrap chargers, but thanks for the advice, i will take care on that :laugh:
Alright well today my screwdrivers (ordered from china) came i disassembled the phone, havent gotten my battery yet but theres some things i would like to note. The first being that the old battery had alot of corrosion along with its contact to to mobo. ill update when i get the new battery in.