Any Gingerbread Rom for N7000? - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Hi Guys,
I wondered if any of you (more experienced, long serving) users are aware of any Gingerbread ROMs? Preferably a CM or any 2.3.7 based, but if they don't exist, any build will do... It needs to be a safe build, a non eMMC bug version, or DeOxed (is that the term)?
Sure, you're gonna say, why bother.. There's JB and KK now, but I like GB and wanted to see what it's like on the N7000?
All help gratefully welcomed..
Thanks, Lister

all GB kernels are safe to wipe data (only stock ICS kernel is unsafe)
i advise you to try Checkrom HD v6, still my favorite GB rom
Sent from my GT-N7000 using xda premium

Hi @ASMI1,
Thanks for such a fast reply.. I've been to the main website where I can download it.. One thing I'm worried about, I've seen in this ROM and mentioned in another GB based ROM for our phones is: CSC?
the CheckRom v6 features "Multi CSC" what does this mean, and is it dangerous?
Do I flash Philz Kernel, and install with that? Do I need to flash another kernel afterwards? Does this room raise the counter or anything?
I'm OK flashing JB or KK, but not done a GB ROM and worried in case summit not aware of, don't want to brick this...?
Thanks, Lister
ASMI1 said:
all GB kernels are safe to wipe data (only stock ICS kernel is unsafe)
i advise you to try Checkrom HD v6, still my favorite GB rom
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse

CSC means customer service code. Multi csc means that this rom is not locked to any country or carrier.
Yes you can flag it under philz kernel.
Sent from my LG-E410

Hi @kaborayyan / @ASMI1 / Guys,
I've flashed Philz original Recovery/Kernel first, and then do all the usual wipes... Factory Reset, System, Davlik Cache (and even tried Pre-Load? after first failed) and same result each time.
During the flashing process it seems to backup the EFS (even though that was the first thing I did when I got this phone, so hope it hasnt over written my original EFS backup) but then gets stuck. It seems to stay on Flashing Modem for ages, and progress bar doesnt move... And then the phone goes black, and it reboots... But then gets stuck on the white Samsung splash screen "Samsung Galaxy Note - GT-N7000" and stays like that, unless I reboot....
I reboot, but notice CWM 5.0.2.7 is installed (not sure if thats a safe one?) so I flash Philz from within that, reboot recovery and then do all the wipes again... and the phone seems like normal again. However I dont know if I've done anything wrong, or if the phone is still safe or if I've killed it any way??? lol
Cheers for any help/support.
Thanks, Lister

Lister Of Smeg said:
Hi @kaborayyan / @ASMI1 / Guys,
I've flashed Philz original Recovery/Kernel first, and then do all the usual wipes... Factory Reset, System, Davlik Cache (and even tried Pre-Load? after first failed) and same result each time.
During the flashing process it seems to backup the EFS (even though that was the first thing I did when I got this phone, so hope it hasnt over written my original EFS backup) but then gets stuck. It seems to stay on Flashing Modem for ages, and progress bar doesnt move... And then the phone goes black, and it reboots... But then gets stuck on the white Samsung splash screen "Samsung Galaxy Note - GT-N7000" and stays like that, unless I reboot....
I reboot, but notice CWM 5.0.2.7 is installed (not sure if thats a safe one?) so I flash Philz from within that, reboot recovery and then do all the wipes again... and the phone seems like normal again. However I dont know if I've done anything wrong, or if the phone is still safe or if I've killed it any way??? lol
Cheers for any help/support.
Thanks, Lister
Click to expand...
Click to collapse
Reboot into recovery again if you found the touch colored recovery then you're on philz kernel. If not be sure that you selected the suitable philz kernel.
If I helped hit the thanks button.

Hi @kaborayyan,
Yep, I'm certainly on Philz Kernel.... when it's loaded, its kind of a pink/purple-ish colour.... (not sure what version, but something like 5.1.1.1) It's the first one I downloaded when I got this phone a couple of months back, that I used to root/and then flash custom roms with... (namely, JB).
However, I fancy seeing what GB is like on it, but get stuck... it seems to hang on Flashing Modem, sits there, and then reboots without finishing by the looks of things...?
Its a UK Vodafone, N7000
Thanks, Lister

Did you try to flash a stock GB ROM through Odin? May be you get better results. Then root it and flash whatever you want of custom GB based Roms.
Sent from my GT-N7000

yeah like kaborayyan said, try to flash any stock GB rom using odin3 v1.85 only (you can find instructions and download links in the sticky thread in the orginal development section, you should look for mirrors because hotfile is down or just download chainfire prerooted stock rom)
After you get a stock rooted GB rom installed on your phone, install checkrom using the recovery after wiping data, cache and dalvik.
as i said stock ICS roms are unsafe, other roms are safe... just keep a backup of your efs
and be careful when using odin3.
btw, hitting the "thanks" button is easier than writing it
cheers
Sent from my GT-N7000 using xda premium

Lister Of Smeg said:
However, I fancy seeing what GB is like on it, but get stuck... it seems to hang on Flashing Modem, sits there, and then reboots without finishing by the looks of things...?
Click to expand...
Click to collapse
Go to www.samsung-updates.com firmware section. There are a few 2.3.6 roms available. Stock though. These roms might be non root able. Not really sure as there are not many methods of rooting GB (check Dr ketans thread for more info) . It could also be possible that for rooting again you will need to flash an ICS or JB rom again using Odin.
If you just want to taste the ginger then stock GB rom is quite fast.

Lister Of Smeg said:
Hi Guys,
I wondered if any of you (more experienced, long serving) users are aware of any Gingerbread ROMs? Preferably a CM or any 2.3.7 based, but if they don't exist, any build will do... It needs to be a safe build, a non eMMC bug version, or DeOxed (is that the term)?
Sure, you're gonna say, why bother.. There's JB and KK now, but I like GB and wanted to see what it's like on the N7000?
All help gratefully welcomed..
Thanks, Lister
Click to expand...
Click to collapse
Pristine LC1 is a good option. Its in the OP of the pristine thread. All GB kernels are safe, as above mentioned.
There is no 2.3.7 or CM based N7000 rom
Sent from Nexus 5 on Slimkat

Hi @ASMI1, @kaborayyan, @nokiamodeln91, @AndroidSlave,
Thanks guys, with you're help.... I've finally made it !!! It appears CheckROM HD v6 does not want to flash under Philz (or some other recovery, cant think what now??) However I did manage to get it to Flash under Abyss Recovery Kernel (which is based on GB kernel, apparently).
So it has flashed now, not had chance to play around with it yet as am at work... But just by looking at it, it's bringing back the GB love....
Yes I know it's sad, why go back to GB?? lol. But sometimes it's just nice to go over, for old times sake... Used to do it on my ZTE Blade many a times...
So, (quick questions).
1) With this stock-ish rom, can I remove/tweak/clean up, and then package it (in CWM) as a flashable rom?? or do I have to backup/restore only in that version of CWM??
2) It safe to flash any version of CM9, without using flashing a seperate recovery afterwards... and still avoid the eMMC. It's only official STOCK firmware that killed them....
Thanks once again guys for all your support, I know its not normal (and frowned upon) to use older firmware... But just wanted to see what GB was like again...
Cheers, Lister

Lister Of Smeg said:
Hi @ASMI1, @kaborayyan, @nokiamodeln91, @AndroidSlave,
Thanks guys, with you're help.... I've finally made it !!! It appears CheckROM HD v6 does not want to flash under Philz (or some other recovery, cant think what now??) However I did manage to get it to Flash under Abyss Recovery Kernel (which is based on GB kernel, apparently).
So it has flashed now, not had chance to play around with it yet as am at work... But just by looking at it, it's bringing back the GB love....
Yes I know it's sad, why go back to GB?? lol. But sometimes it's just nice to go over, for old times sake... Used to do it on my ZTE Blade many a times...
So, (quick questions).
1) With this stock-ish rom, can I remove/tweak/clean up, and then package it (in CWM) as a flashable rom?? or do I have to backup/restore only in that version of CWM??
2) It safe to flash any version of CM9, without using flashing a seperate recovery afterwards... and still avoid the eMMC. It's only official STOCK firmware that killed them....
Thanks once again guys for all your support, I know its not normal (and frowned upon) to use older firmware... But just wanted to see what GB was like again...
Cheers, Lister
Click to expand...
Click to collapse
1) not really unless you use a new version of philz touch recovery, which wouldn't happen because on the n7000 the recovery sits on the kernel, thus you are stuck with an old kernel and old recovery. As such your best bet is to do a nandroid backup. Further - when you restore such a backup, I recommend flashing abyss again first so you are in the Ame recovery it was made in
2) yes. Just be concerned of Stock ICS (4.0.4) with a custom recovery. Never flash temporary cwm.zip. matter of fact, just avoid stock ICS at all costs. Newer versions of cm9 are safe. Avoid very old cm9 versions. My personal recommendation to you would be Paranoid Android cm9 ( I think it stopped at around .4a) that one was amazing.
Sent from Nexus 5 on Slimkat

Related

[Q]Should I use CWM or odin to flash 4.0rom like romow?

I know this is a very stupid question but I just want to make sure flashing with CWM is viable.
For the leaked stock ics 4.0 rom I know I should use odin to flash, but how about custom 4.0 rom like Romow? Should I use CWM to flash the zip file?
Thx~
ps: I am currently running rocketrom v19 with CWM
use CWM n flash zip
Sent from my GT-N7000 using xda premium
You should read in the post how must it be done, you should start in annual kernel 3.9 then install chainfire.repack and so on
Sent from my GT-N7000 using xda premium
There are no instructions in romow's thread and that's why i am here to ask for any further instructions. I bet flashing a 4.0custom rom is similar to flashing Gingerbread rom. Am i right?
Also, some ppl claimed that I need to first flash the stock leaked 4.0 rom then have my phone rooted with CWM installed and finally flash custom 4.0 rom with CWM. Is that really necessary?
Sent from my GT-N7000 using XDA App
kelvin fong said:
There are no instructions in romow's thread and that's why i am here to ask for any further instructions. I bet flashing a 4.0custom rom is similar to flashing Gingerbread rom. Am i right?
Sent from my GT-N7000 using XDA App
Click to expand...
Click to collapse
There are better roms now than ROMOW's one i think, try flashing Rocket Rom, or the new AOSP
From the instructions given in [02/24/12][Team Rocket ROM][open beta ICS v4.0.3][v1.5][15Tooglebar] daily ROM now! , it seems I really have to flash the leaked ics rom first before installing the rocketrom 4.0.3 rom, is that true? That means I cannot directly install the ics rocketrom from any gingerbread custom rom?
kelvin fong said:
From the instructions given in [02/24/12][Team Rocket ROM][open beta ICS v4.0.3][v1.5][15Tooglebar] daily ROM now! , it seems I really have to flash the leaked ics rom first before installing the rocketrom 4.0.3 rom, is that true? That means I cannot directly install the ics rocketrom from any gingerbread custom rom?
Click to expand...
Click to collapse
Yes youre right, there is a problem with root a cwm in ics, and you need to da that
Follow carefully the instructiones if not you wont hace fullroot
PROBLEMS!
Just have to ask it right here as well...I went to romow yesterday for testing reasons (just flashed the zip in cwm) but I have to go back since there are too many bugs imao atm.
Just tried to go back to my CWM Backup....now I´m stucked at the bootanimation!
Do you guys know what could be the reason here? And what I could do to get my nandroid backup working again?
brooon said:
Just have to ask it right here as well...I went to romow yesterday for testing reasons (just flashed the zip in cwm) but I have to go back since there are too many bugs imao atm.
Just tried to go back to my CWM Backup....now I´m stucked at the bootanimation!
Do you guys know what could be the reason here? And what I could do to get my nandroid backup working again?
Click to expand...
Click to collapse
Did you flash 4.0.3 directly from gingerbread rom? BTW I've heard many people say their phones were stuck in the bootscreen(The samsung N7000 with no boot animation) when they tried to go back from ics to gingerbread. Seems this is a common problem....
kelvin fong said:
Did you flash 4.0.3 directly from gingerbread rom? BTW I've heard many people say their phones were stuck in the bootscreen(The samsung N7000 with no boot animation) when they tried to go back from ics to gingerbread. Seems this is a common problem....
Click to expand...
Click to collapse
Yes, I came directly from GB!
If you can load the boot animation that means ur phone is not bricked. You should try to download a stock gingerbread rom from dr ketan's post and flash it by odin pc.
Sent from my GT-N7000 using XDA App
When going back to GB, i kinda 'restart' the whole process by going back to Stock ROM via Odin, and redo the root and CWM.
Else, there are strange quirky issue ex. CWM just hangs while wiping the phone.
Hey Kelvin Fong & J.wong, thank you guys for your support!
Sorry for noobing around from now on...I´m not exactly the newest guy when it comes to these flash-things, but I have to admit that I´m kind of confused now...
I tried to find dr. ketans thread (this one?) but I´m not getting into his post (sorry for that, as I said: I´m confused!):
dr.ketan said:
Now How I can revert back to Stock ROM/Unroot (In case of replacemet may i need)
If You have Root + CWM - then first find out original stock kernel (zImage file)
Now place this file in zImage folder, n repeat procedure(Initial CFRoot Flasher), which you have done at time of pushing CWM by selecting I am rooted already
Now unroot with above said unrooting tool.
Click to expand...
Click to collapse
The first thing I´ve made evertime in the past was to read the full-noob tutorials...for some reason, I can´t find something like that for the note!
May I kindly ask you if you know a thread were these things (and perhaps the results after going back to stock) are explained from scratch again? Just want to understand what I have to do and how, it´s getting harder to find some information that are not based on years of flash-training
brooon said:
Hey Kelvin Fong & J.wong, thank you guys for your support!
Sorry for noobing around from now on...I´m not exactly the newest guy when it comes to these flash-things, but I have to admit that I´m kind of confused now...
I tried to find dr. ketans thread (this one?) but I´m not getting into his post (sorry for that, as I said: I´m confused!):
The first thing I´ve made evertime in the past was to read the full-noob tutorials...for some reason, I can´t find something like that for the note!
May I kindly ask you if you know a thread were these things (and perhaps the results after going back to stock) are explained from scratch again? Just want to understand what I have to do and how, it´s getting harder to find some information that are not based on years of flash-training
Click to expand...
Click to collapse
Should be this one(http://forum.xda-developers.com/showthread.php?t=1424997).
Firstly, download one of the roms from [Older ROMs (Directly Rootable)].
Secondly, follow the [Installation Guide For Older ROM ], the one using odin pc.
You may see below another flashing method using mobile odin, but that doesn't suit you since that one requires your phone rooted before and will keep your root after flashing. The one with odin pc will wipe out all your data and apps(of course not your SD card) and also unroot your phone. That means your CWM and root will all be gone and you have to follow another post to root it again(now this one:http://forum.xda-developers.com/showthread.php?t=1329360)
this one(http://forum.xda-developers.com/showthread.php?t=1424997)teaches you how to flash a rootable gingerbread rom, but not rooted. This one(http://forum.xda-developers.com/showthread.php?t=1329360)shows you how to root your phone and install CWM. I think these two posts are the best tutorials you are looking for.
I think you should download this >>http://forum.xda-developers.com/attachment.php?attachmentid=907734&d=1329574136
This one is better organized.
Thanks mate! Saved it to my desktop...but finally i was able to manage the problem by simply flashing a *fresh* RocketRom again (?!). I thought it would be worth a try...
Anyway: Thank you very much for your support, it´s good to still meet that friendly kind of people with patience here on the board (it´s getting less these days) hope i´ll be able to return the favor in future
You are welcome! Please note your binary counter may increase if you flash a rooted rom like rocketrom you've mentioned above directly via odin.
kelvin fong said:
You are welcome! Please note your binary counter may increase if you flash a rooted rom like rocketrom you've mentioned above directly via odin.
Click to expand...
Click to collapse
As far as I remember I made my very first steps with odin after I reveived my note (root, cwm)...rocket has been flashed by using cwm. But yes, my binary counter increased definitely...
...I do have a USB Jig, but in some was I am kind of afraid of going trough this! To fumble around in pure darkness...hmmm i don´t know
Have you tried it yourself?
Actually I've got a yellow triangle together with increased binary counter as I followed another tutorial guide(I should follow dr ketan's guide before).
I think removing the counter with a jig is way too dangerous for me so I don't want to risk it. Simply remove the counter only when you really need to bring your phone to samsung because maybe you don't even have to claim the warranty at all.

[Q] [ROM] Criskelo's ICS V7 install question

Hi Guys,
sorry for this noobie question but I'm quite new to android.
I've passed hours reading the forum about roms, kernels etc...but there are so much information for my little brain that now I don't know what to do...
So I'm on a GB 2.3.6 XXLC1 stock rom, with Franco's kernel 3.x version and I'd like to install Crisleko's ICS V7 ROM on my device but i'm not able to know how really to install it on the phone...the phone is full rooted. I wouldn't like to brick my note, so here's the reason of my question :
In my case, which is the most efficient way to install this rom ?
Sorry if this question has already been posted, but within all answer, I don't know what to do....
Thanks a lot for yout support.
You can flash the rom also directly from CWM. The reboot into recovery and select : _install zip from sd card _chose zip from sd card _select the criskeloRom zip _click yes ...... Flash it from Cwm i raccomend the Cwm app.from chainfire : _copy the rom to internal sd _start Cwm manager _ chose flash update _select criskelo Rom _click on yes...
I'm also afraid to hardbrick my device, and dude, i bought it 5 days ago lol
I had a Galaxy Nexus and flashed, installed new kernels, rooted, did everything.
I asked few ppl here and they said we should wait till the official ICS comes, it will take 1 or 2 weeks, better than hardbrick my note <3
Not quite because most bricks actually happen because of the stock ICS ROM.
Flash whatever you want, just remember to go from GB and not stock ICS, and remember - never do a factory reset while on stock ICS kernel.
If you need to do a factory reset, just flash a GB kernel, or flash GB stock with Odin, then wipe and flash ICS back.
Also, CM9 highly recommended
Ok guys, thanks a lot for answers. I've tryed to flash this rom and everything worked fine except the fact I'm a noobie and restore with TB Apps and user datas ^^. Now i'll know that user data don't have to be restored !
So I'm came back to my GB rom...
Maybe one more question :
I'll installed a new rom, I think i've understood what to do and what not to do with wipe from ICS roms but after wipe data / factory resest ans dalvik cache, is there a way to have a connection wizard software so a to set everything up because I had no data connection anymore ?
Thank a lot for your support
Hello Pascal-T,
I think I'm in the exact same position as you (except that I'm not rooted yet), but i'm also on GB LC1 and I want to go to Crisleko's ICS V7 ROM !
As I understood, you have directly install Crisleko's ICS V7 ROM on your rooted GB LC1 ? So it's not needed to install an other lower ICS ROM before going to the LQ3 of Criskelo ?
If yes this is great, then I just have to root my GB LC1, do a backup up with TB, and then I can follow Crisleko's ICS V7 ROM topic ? (At the begining I though I should first flash a stock ICM ROM but It seems to be THE THING TO AVOID).
If someone can just confirm these informations, that would be perfect
Thank you !
Well this seems like a perfect place for me to post Ive asked around, And searched a lot, But still cant figure this out. I dont wanna sound like a noob ( I am to the Note )
Ive been flashing and modding for years, Samsungs, HTC's, Sony Ericssons so I know what to do.
The thing is, All the threads I read about the bricking, and how to avoid it, Just keep forever linking me to different threads, and i end up back at the start. I dont have the Note yet (should be arriving any time) Im thinking of Only rooting for now as im not confident enough to flash without errors. But when i do, what i need to do is, Use ODIN to revert to GB (Unless it comes with GB) then:
1, Flash CF-ROOT kernel
2, Flash abyss safe kernel in cwm
3, reboot back into cwm
4, Do a full wipe
5, Install a ROM
Is that right ? I like the look of PA but would like to try a modded stock ROM to start with, So any recommendations ?
TIA
A-D

[Q] Galaxy Note GT N7000 eMMC Bug/Kernel Related Question

Hi, I have an international varient of the Galaxy Note GT N7000 which using Chainfire's Got Brick App v1.1 says:
eMMC Chip
Type: VYL00M
Revision: 0x19
Verdict: Danger! This eMMC chip is "Known" to have the brick bug!
I once had installed a custom Kingdroid ROM v3 and wiped it but it had resulted in a Hardbrick/Superbrick so i had to take it Samsung Service Center to get it fixed. They have repaired it and given me back the handset with the Stock ICS ROM. Here are the details:
Model Number: GT-N7000
Android Version: 4.0.3
Baseband Version: N7000XXLPT
Kernel Version: 3.0.15-N7000JPLPD-CL643396
[email protected]#3
SMP PREEMPT Thu May 31...
Build Number: IM74K.JPLPD
Now i have done some researched and found that this bug is only triggered with kernels (ICS stock & leaked) which have the eMMC_Erase function/command. GB kernels are not known to have this erase function so they are safe.. Also the two safe kernels are franco r3 and speedmod k3 (Correct me if im wrong). Can anyone please guide me on the following:
1) Should I flash Stock Gingerbread OR ICS Kernel(franco/speedmod)?
2) Should I use Recover or ODIN?
3) Plz Provide the links for the Kernels - Franco R3 & Speedmod K3 which are safe?
4) Will the above Kernels provide root access?
5) Is abyss kernel safe (because it supports GPU overclock)?
6) Can i flash an ICS kernel over a Gingerbread ROM?
For answering please answer in a similar numbered way so that it is easy to read and understand for me as well as future audience! Thanking everyone who takes time to read and answer!
I use Speedmod kernel and i confirm that it is safe (for me at least anyway) Im using CleaNote ICS ROM, So I would suggest you also use speedmod kernel,
You Flash it in Odin, It will give you CWM and Root too !
Ive attached the kernel to the post for you.
Abyss kernel is safe, But its for GB ROMs only, You are on ICS so it wont work.
I dont know if you can flash ICS kernel over GB ROM, However, Your are on ICS so you shouldnt need to worry about that.
don't really want to hijack your thread an i dont really want to make a whole new thread for a simple question.
as a noob, im just wanting to know, if i update my stock gb to stock ics via software update, are there still chances of this emmc bug/brick thats going on?
and the battery drain issues, do they only exist in custom roms or does it exist in stock roms too?
cheers.
azzledazzle said:
I use Speedmod kernel and i confirm that it is safe (for me at least anyway) Im using CleaNote ICS ROM, So I would suggest you also use speedmod kernel,
Click to expand...
Click to collapse
Thanks for the confirmation mate, one more thing to ask you: Is the speedmod kernel faster than the stock ICS kernel? Is there any flaws such as battery drain/WIFI problem with it? Also does it support GPU OC? Thanks once again for your help!
little-vince said:
don't really want to hijack your thread an i dont really want to make a whole new thread for a simple question.
as a noob, im just wanting to know, if i update my stock gb to stock ics via software update, are there still chances of this emmc bug/brick thats going on?
and the battery drain issues, do they only exist in custom roms or does it exist in stock roms too?
cheers.
Click to expand...
Click to collapse
Firstly get your Galaxy Note checked using Chainfires App (Gotbrick v1.1). If the verdict says "Danger" only then does your device have this problem. My Galaxy Note (Rev 0x19) had this problem and came with GB out of the box and i upgraded it to ICS through Samsung Kies and it worked fine. So i do not think that while updating to ICS via Kies will cause this problem. As of what i know it is triggered when a command eMMC errase is triggered when either doing a factory reset or wipe through recovery. The update as such did not brick my device, however this does not mean it cannot brick yours. I am no expert on this so be a little cautious while updating. I would suggest stick to GB until Samsung Releases a safe stock ICS ROM with a safe Kernel. Cheers!
really easy
1: (optional ) in GB do factory reset (after you have made a backup with TB)
2: put phone in Download mode.
3: use PC odin flash STOCK ICS rom
4: reboot device let it load
5: put device back into download mode
6: use PC ODIN flash Speedmod k3-3
7: reboot
8: launch CWM and tell it to reboot in cwm recovery
9: load your custom rom of your choice
i HIGHLY recommend doing ONLY THE FACTORY RESET WIPE data and cache in GB before you start anything.
ONCE you are in ICS and have successfully loaded speedmod or franco's kernel then it is safe to do a factory wipe if you want. but ONLY after one of those 2 Kernels are on your device.
EMMC BUG. is affected in all N7000 Devices only . only the devices sent to the USA have the revision the non 0x19 bug .
rp4k said:
EMMC BUG. is affected in all N7000 Devices only . only the devices sent to the USA have the revision the non 0x19 bug .
Click to expand...
Click to collapse
okay...
truth is i haven't actually bought the note yet.
just doing substantial amounts of research beforehand.
im pretty sure only the n7000 model is out in australia.
but it's all okay if i dont factory reset/wipe/anything-risky-in-general right?
little-vince said:
okay...
truth is i haven't actually bought the note yet.
just doing substantial amounts of research beforehand.
im pretty sure only the n7000 model is out in australia.
but it's all okay if i dont factory reset/wipe/anything-risky-in-general right?
Click to expand...
Click to collapse
Yes, this bug is known to trigger usually when you do a wipe using the recovery. However there have been some cases when doing a factory reset via the settings has also resulted in a brick. However if you stay away from recovery and do not intend to doing flashing/wipes then i guess you should be ok. And it is a matter of time before Samsung Comes up with a solution. They are said to be working on this bug already. I have the N7000 which i bricked once while flashing and then wiping but i got it repaired since i had warranty. Since then i have stayed away from wiping or installing any custom roms so the device has not given any problems. Hope this info helps! Cheers!
Rom doesnt load during boot
Dear Developers
I rooted my galaxy note and soon as that i got gained super user access for chain fire app, then i flashed CWM and installed crisello rom with abbysys kernel , it installed all the files correctly and soon after that the phone rebooted .After reboot the phone went inside the boot menu ( the world of galaxy UI boot menu ) and it frozen since then
i tired flashing various custom or stock roms and still the same problem i face
If someone could help me out on what the problem is and how i could get a fix to it
cuteglen said:
Dear Developers
I rooted my galaxy note and soon as that i got gained super user access for chain fire app, then i flashed CWM and installed crisello rom with abbysys kernel , it installed all the files correctly and soon after that the phone rebooted .After reboot the phone went inside the boot menu ( the world of galaxy UI boot menu ) and it frozen since then
i tired flashing various custom or stock roms and still the same problem i face
If someone could help me out on what the problem is and how i could get a fix to it
Click to expand...
Click to collapse
What rom are you on? Have you performed any wipes or factory resets?
Sent from my GT-N7000 using xda premium
Hi everybody
I have three questions if You can help me
1- Are speedmode and franco Kernels the only safe kernels for stock ICS?
2- Can I flash CM9 from stock ICS or it is safer to do it from GB rom?
3- Can I flash CM9 kernel for stock rom?
Thanx in advance
iraqi4ever80 said:
Hi everybody
I have three questions if You can help me
1- Are speedmode and franco Kernels the only safe kernels for stock ICS?
2- Can I flash CM9 from stock ICS or it is safer to do it from GB rom?
3- Can I flash CM9 kernel for stock rom?
Thanx in advance
Click to expand...
Click to collapse
1. Afaik yes
2. NO, you'll brick, flash from GB kernel, I know some have done from abyss.
3. No. CM based not compatible with Touchwiz framework.
Sent from my GT-N7000 using xda premium
I have a quick ( hopefully) question about the brick bug. I already asked but I think a mod must have deleted the whole thread, even though the thread was about the brick bug and I think I might have been bringing a new way ( well for some anyway) to flash safely to new ROMs.
So anyway, I have a 'safe' kernel ( speedmod), and I want to try out 4.0.4 stock ROM. I have extracted the stock ROM zip and the tar file inside. In there is the Zimage.
Do I just delete the Zimage then re-zip and flash from CWM?
OR Do I have to replace the Zimage with another, 'safe', Zimage ( for example just put the zimage in there from speedmod because I want to keep that for now). Does there NEED to be A Zimage there, or will it work fine without one. I don't want to start flashing the ROM and it get stuck half way through.
If it will work this way then this might be a fairly easy way for anybody to flash any new ROM they want. They'll just need to get a safe kernel on there in the first place.
SpyderTracks said:
1. Afaik yes
2. NO, you'll brick, flash from GB kernel, I know some have done from abyss.
3. No. CM based not compatible with Touchwiz framework.
Sent from my GT-N7000 using xda premium
Click to expand...
Click to collapse
thank you for your response
just to be sure you said that it is unsafe to flash CM9 from stock ICS?
can we flash CM9 from stock ICS rom with safe kernel such as franco or speedmod
sorry for bothering you and thank you again
iraqi4ever80 said:
thank you for your response
just to be sure you said that it is unsafe to flash CM9 from stock ICS?
can we flash CM9 from stock ICS rom with safe kernel such as franco or speedmod
sorry for bothering you and thank you again
Click to expand...
Click to collapse
Only from GB kernel such as abyss. If you flash from ics kernel you WILL brick. This goes for all cm based roms.
Sent from my GT-N7000 using xda premium
kyllerbuzcut said:
I have a quick ( hopefully) question about the brick bug. I already asked but I think a mod must have deleted the whole thread, even though the thread was about the brick bug and I think I might have been bringing a new way ( well for some anyway) to flash safely to new ROMs.
So anyway, I have a 'safe' kernel ( speedmod), and I want to try out 4.0.4 stock ROM. I have extracted the stock ROM zip and the tar file inside. In there is the Zimage.
Do I just delete the Zimage then re-zip and flash from CWM?
OR Do I have to replace the Zimage with another, 'safe', Zimage ( for example just put the zimage in there from speedmod because I want to keep that for now). Does there NEED to be A Zimage there, or will it work fine without one. I don't want to start flashing the ROM and it get stuck half way through.
If it will work this way then this might be a fairly easy way for anybody to flash any new ROM they want. They'll just need to get a safe kernel on there in the first place.
Click to expand...
Click to collapse
Hiya, yep, you can just delete the zimage file, no need to replace, it will just skip writing that partition.
Sent from my GT-N7000 using xda premium
Gave that a go last night and I must not be doing something right. Either I need to re-zip it differently or I need to use something other than CWM (mobile odin?) because it's just aborting before it actually starts flashing anything.
Suppose I could always flash the separate elements on pc odin?
kyllerbuzcut said:
Gave that a go last night and I must not be doing something right. Either I need to re-zip it differently or I need to use something other than CWM (mobile odin?) because it's just aborting before it actually starts flashing anything.
Suppose I could always flash the separate elements on pc odin?
Click to expand...
Click to collapse
Try mobile odin. If you point to the tar, it should load all the components. You can then review which components are being flashed.
Sent from my GT-N7000 using xda premium
iraqi4ever80 said:
Hi everybody
I have three questions if You can help me
1- Are speedmode and franco Kernels the only safe kernels for stock ICS?
2- Can I flash CM9 from stock ICS or it is safer to do it from GB rom?
3- Can I flash CM9 kernel for stock rom?
Thanx in advance
Click to expand...
Click to collapse
1. Add goku, dafuq, gl-notecore and abyss42 (GB) to your list.
2. Only do it from a GB firmware or at least a GB kernel like abyss42. SPECIFIC instructions per firmware is listed for a reason. Follow those instructions to the letter.
3. No.
Sent from my GT-N7000 using xda app-developers app
kyllerbuzcut said:
Gave that a go last night and I must not be doing something right. Either I need to re-zip it differently or I need to use something other than CWM (mobile odin?) because it's just aborting before it actually starts flashing anything.
Suppose I could always flash the separate elements on pc odin?
Click to expand...
Click to collapse
Stock rom in a zip? Are you sure you are nit flashing a custom rom? Point us to the file/thread please.
If it is a custom rom, the it is meant to be via CWM.
1. Flash abyss42
2. Reboot recovery
3. Do your wipes
4. Flash.
Im sure there is a specific instruction on where you got that file. Or better yet, go to dr. Ketans thread and get your stock rom from there.
Sent from my GT-N7000 using xda app-developers app
It's just the standard rom file from sammobile.It does come as a zip you know. If you unzip it, then use rar on it you can see all the bits. I thought if I just put a different zimage in there it would just go ahead and use that, but didn't seem to like it after I zipped it all back up again.
Tonight I've ended up getting chainfires excellent CF-Root kernel.Flashed that through odin, over my speedmod kernel.
Put just the factoryfs part of the stock rom zip onto the SD card and flashed that using the cwm app that CF-Root installs for you.. Now have CF-Root kernel and 4.0.4 firmware.
If you don't already have a "safe" kernel then I dunno what the brick chances would be, but since I had a safe one already I thought it couldn't hurt to try it out.
The reason I haven't flashed the hidden, cache, model and sbl parts of the zip is that simply they wouldn't fit on my SD card If it behaves funny or I can make space then I'll try the rest too. And the reason I didn't flash the zimage from the zip should be fairly obvious. Because I don't want a brick
EDIT: I managed to clear some space on the SD and flashed the rest of it. Seems to be working ok, so far anyway. I'm hoping the battery issues from 4.0.3 will be a little better. This is a really good way of doing it all as you can just swap out a potentially bad kernel for one that has been 'protected' by having te emmc cap erase turned off.

Newbie wants to flash a custom ROM, Got some questions!!!

Hello,
I've being reading a lot this forums and I really wish to Flash a custom Rom.
My steps so far:
I updated my Galaxy Note N7000 throught Odin to version 4.0.4.
Then I rooted the phone using CWM folling the instructions from dr.ketan.
Can I just simply flash a rom using CWM or should I downgrade the phone to GB? Do I have to flash a custom Kernel or no? BTW mine is stock.
I really wish to flash a rom but i dont want to brick my phone.
Sorry for my English, is not my main language.
Thanks
If you're familiar with using Odin and flashing ROMs like that, then I mostly recommend reverting to GB, getting root + CWM also according to dr. Ketan's guide. You'll find stock GB and how to root them in the Development Section Stickies
So far, the only 100% safe way to flash custom ROMs (ICS or others) through CWM is with a working Gingerbread CWM. Some would recommend flashing through Abyss Kernel, or flashing through mobile Odin.
Again, and this is coming from one of our top-notch devs... The only 100% safe way is to flash from a rooted GB.
Also, while we're on it, may I also recommend Cyanogen Mod 9 (you'll find it in the General section of the forum) and CM9 - based ROMs. They have a safe kernel, that means you can flash and full-wipe as much as you want from CM, without reverting back to GB. CM9 also gave me the best performance and battery consumption so far. Only disadvantage would be if you don't like the stock Android look and would rather have an S3 - feel or TouchWiz or whatever.
Also VERY IMPORTANT!!! DO NOT FULL-WIPE (Factory Reset) from your ICS!!! That's how phones get bricked, that's why you shouldn't flash from stock rooted ICS!
Best of luck and let me know if you need anything else!
Cheers and welcome to XDA
Helpful Links:
- Stock ROMs
- Rooting and CWM
- Cyanogen Mod 9 (If you decide to use it)
eug3n91 said:
If you're familiar with using Odin and flashing ROMs like that, then I mostly recommend reverting to GB, getting root + CWM also according to dr. Ketan's guide. You'll find stock GB and how to root them in the Development Section Stickies
So far, the only 100% safe way to flash custom ROMs (ICS or others) through CWM is with a working Gingerbread CWM. Some would recommend flashing through Abyss Kernel, or flashing through mobile Odin.
Again, and this is coming from one of our top-notch devs... The only 100% safe way is to flash from a rooted GB.
Also, while we're on it, may I also recommend Cyanogen Mod 9 (you'll find it in the General section of the forum) and CM9 - based ROMs. They have a safe kernel, that means you can flash and full-wipe as much as you want from CM, without reverting back to GB. CM9 also gave me the best performance and battery consumption so far. Only disadvantage would be if you don't like the stock Android look and would rather have an S3 - feel or TouchWiz or whatever.
Also VERY IMPORTANT!!! DO NOT FULL-WIPE (Factory Reset) from your ICS!!! That's how phones get bricked, that's why you shouldn't flash from stock rooted ICS!
Best of luck and let me know if you need anything else!
Cheers and welcome to XDA
Helpful Links:
- Stock ROMs
- Rooting and CWM
- Cyanogen Mod 9 (If you decide to use it)
Click to expand...
Click to collapse
^^ This
eug3n91 said:
If you're familiar with using Odin and flashing ROMs like that, then I mostly recommend reverting to GB, getting root + CWM also according to dr. Ketan's guide. You'll find stock GB and how to root them in the Development Section Stickies
So far, the only 100% safe way to flash custom ROMs (ICS or others) through CWM is with a working Gingerbread CWM. Some would recommend flashing through Abyss Kernel, or flashing through mobile Odin.
Again, and this is coming from one of our top-notch devs... The only 100% safe way is to flash from a rooted GB.
Also, while we're on it, may I also recommend Cyanogen Mod 9 (you'll find it in the General section of the forum) and CM9 - based ROMs. They have a safe kernel, that means you can flash and full-wipe as much as you want from CM, without reverting back to GB. CM9 also gave me the best performance and battery consumption so far. Only disadvantage would be if you don't like the stock Android look and would rather have an S3 - feel or TouchWiz or whatever.
Also VERY IMPORTANT!!! DO NOT FULL-WIPE (Factory Reset) from your ICS!!! That's how phones get bricked, that's why you shouldn't flash from stock rooted ICS!
Best of luck and let me know if you need anything else!
Cheers and welcome to XDA
Helpful Links:
- Stock ROMs
- Rooting and CWM
- Cyanogen Mod 9 (If you decide to use it)
Click to expand...
Click to collapse
i found this a very good summary and guide of all thats going on here. i too want to try all the custom roms,
suppose one has a certain ics TW rom installed but would like to change the kernel to a another one, then which is the right method please ?pc odin, mobile odin, or CMW that comes with that particular rom installed ?
rraaka said:
i found this a very good summary and guide of all thats going on here. i too want to try all the custom roms,
suppose one has a certain ics TW rom installed but would like to change the kernel to a another one, then which is the right method please ?pc odin, mobile odin, or CMW that comes with that particular rom installed ?
Click to expand...
Click to collapse
That mostly depends. Best way would be to either ask in the ROM's thread or in the kernel's thread. Some ROMs might recommend you flashed in the following sequence:
- Reboot into recovery
- Flash Abyss Kernel 4.2 Redpill (Original or custom logo, doesn't matter)
- IMPORTANT! Go to advanced => Reboot recovery
- Flash the kernel of your choice
- Reboot system
Others might recommend you flashed directly from the included CWM. Again, I'm not sure there's really a rule to this...
So far the only totally safe, non-headache kernel + ROM is Cyanogen and all Cyanogen-based, like Paranoid, Asylum and a few others. If you run those you can flash and full-wipe at will. With others, you should either ask or do a little thread-searching.
And also make sure that if you're running a TouchWiz ROM, flash a TouchWiz kernel. That's...really important, for obvious reasons and the type should be specified in the kernel's description or first post
Got a problem!!!
I flashed a Stock GB rom and the phone is giving me the next problem:
"Unfortunately, the process com.android.phone has stopped"
What should I do?????
darielsantana said:
I flashed a Stock GB rom and the phone is giving me the next problem:
"Unfortunately, the process com.android.phone has stopped"
What should I do?????
Click to expand...
Click to collapse
Just go into recovery and do a full-wipe. If the problem persists, try another ROM.
Full-wipe should do the trick, though.
eug3n91 said:
Just go into recovery and do a full-wipe. If the problem persists, try another ROM.
Full-wipe should do the trick, though.
Click to expand...
Click to collapse
I think i bricked my phone . I did the full-wipe and i cant get to recovery and when i try to flash a rom it stops at "FACTORYFS"
darielsantana said:
I think i bricked my phone . I did the full-wipe and i cant get to recovery and when i try to flash a rom it stops at "FACTORYFS"
Click to expand...
Click to collapse
I flash a Kernel and now can get to Recovery, what should i do?
darielsantana said:
I think i bricked my phone . I did the full-wipe and i cant get to recovery and when i try to flash a rom it stops at "FACTORYFS"
Click to expand...
Click to collapse
Uhm...I think you full - wiped from ICS... maybe accidentally flashed an ICS stock ROM instead of GB?
GB stock kernels don't do that...
First of all you should consider reading a few threads of people that have already been through this and gotten out ok.
Chances are you'll be able to flash a new ROM from there, but a little research is in order. I don't really know your exact situation (what ROM you have on and what kernel),and I haven't been in this pickle myself, so I may not be the best to advise you on this.
However, it is VERY unlikely that you're on GB... The emmc bug that you've described is typical for early ICS builds.

Putting ICS on My N7000

I just purchased a international Note off EBay. It has GB installed. I am not sure what country this is from but the phone's baseband version is N7000UBKK1 and the kernel version is 2.6.35.7-N7000UBKK2-CL705203. I would like to move to ICS. I need US English as the language. So:
(a) What firmware should I use? I want to use Odin to install.
(b) Is there any possibility of bricking my phone due to the eMMC issue? I have run the eMMC Check app from the Play Store and it says the chip is "insane". But the test of the memory completes without errors. I am not really sure I know what this all means but I want to avoid problems (who doesn't).
(c) I understand the brick problem is with ICS and not GB. Does this continue to be a problem with the various JB roms out there?
Thanks for your time and help.
Flash stock open German XXLRQ then, look for it in dr.ketan's thread for stock roms in note original android dev sticy.
There are no official jb roms for note yet and cm10 or aokp based custom jb roms are totally safe for wipes and all.
Sent from my GT-N7000
For people who just Dont know what version they need to install u can check this from settings -about,or simply just install kies and it will detect ur version,then u can let kies install it for u or u can download it from dr.ketan post then root it then flash any safe kernel as speedmod ir hydracore,one last thing just remember not 2 make any wipes while using stock ICS thats all.
↖(^▽^)↗ Sent from Rego Galaxy Note ↖(^▽^)↗
The brick bug only triggers on unsafe kernels like stock ICS and only if you do wipes like factory resets.
Sent from my GT-N7000 using Xparent SkyBlue Tapatalk 2
So Should I NOT Use a Stock ICS ROM?
Markuzy said:
The brick bug only triggers on unsafe kernels like stock ICS and only if you do wipes like factory resets.
Sent from my GT-N7000 using Xparent SkyBlue Tapatalk 2
Click to expand...
Click to collapse
Hello and thanks to you and the others who have so kindly replied. Does this mean I should find a non-stock ICS ROM to install? I was thinking that going stock would be safer. I was reading this guide <android.gs/update-samsung-galaxy-note-to-official-xxlrq-firmware-update> to updating to the ROM suggested above and near the end it speaks to possibly having to select ‘wipe data/ factory reset’ in recovery mode if, after the Odin install completes, the device fails to boot beyond the logo screen. I would not want to get to that point and not be able to do this if needed.
Also, I would eventually really like to get to JB - especially for the on-device voice command processing. If there is a recommended JB ROM that can do this now and avoid the brick problem, I would appreciate recommendations.
Thanks again for your knowledge and help.
whitedavidp said:
Hello and thanks to you and the others who have so kindly replied. Does this mean I should find a non-stock ICS ROM to install? I was thinking that going stock would be safer. I was reading this guide <android.gs/update-samsung-galaxy-note-to-official-xxlrq-firmware-update> to updating to the ROM suggested above and near the end it speaks to possibly having to select ‘wipe data/ factory reset’ in recovery mode if, after the Odin install completes, the device fails to boot beyond the logo screen. I would not want to get to that point and not be able to do this if needed.
Also, I would eventually really like to get to JB - especially for the on-device voice command processing. If there is a recommended JB ROM that can do this now and avoid the brick problem, I would appreciate recommendations.
Thanks again for your knowledge and help.
Click to expand...
Click to collapse
ofc you can use ICS Stock Rom. But just to be safe you have to flash safe kernel...Speedmod/Notecore/HydraCore are the safer kernels.
For JB there is no official update available from Samsung for our Note. But you can enjoy it with the efforts that developers are doing for us in XDA.
Go to Android Development Section and Have a look on the Topic Titles.Some of them are AOKP/PA/CM10/AOSP... For Me JellyCore is so far gud. You can find the link in my signatures.
I only know u r now in GB.
GB shld be ok to do full wipe. None reporting mmc brick on GB coz of full wipe.
So....
U can do ur full wipe first on stock GB.
Use pc odin to flash ICS 4.04 LRQ.
Voila.... U r on ICS alrd.
Once u r on ics, and on stock ics kernel....
Pls, do not ever do full wipe.
Unless, after that u root and install ics safe custom kernel, then u r safe to full wipe on ics.
Good luck!
Sent from my GT-N7000 at the corner of this rounded earth.
More in Jelly Core?
sahilarora2003 said:
ofc you can use ICS Stock Rom. But just to be safe you have to flash safe kernel...Speedmod/Notecore/HydraCore are the safer kernels.
For JB there is no official update available from Samsung for our Note. But you can enjoy it with the efforts that developers are doing for us in XDA.
Go to Android Development Section and Have a look on the Topic Titles.Some of them are AOKP/PA/CM10/AOSP... For Me JellyCore is so far gud. You can find the link in my signatures.
Click to expand...
Click to collapse
Hello and thanks. I guess it may make sense to bypass the stock ICS which seems to contain issues related to the brick bug and go to something like Jelly Core as you mention. I looked at the page for Jelly Core and see that it says to install using Clock Work Mod and to wipe from a safe kernel first. As a newbie I guess I have some questions:
(a) I am on GB which I understand to be "safe". Is that correct?
(b) Where do I get the CWM for this phone and how do I install it?
(c) To do the "wipe" does that simply mean to use the built-in reset to factory or does this mean something else?
Thanks
Hi there,
a. Yes, Stock GB's are generally safe
b. When your going to flash ROM, each ROM has it's own accompanying CWM.. so when your done choosing which ROM your going to flash your Note to, when your going to bootup in recovery.. and you get the standard CWMR...
c. Yes, Wiping is synonymous to doing the built-in factory reset on your phone (thru Settings), or the alternate way is to go to CWMR and wipe data. Different Methods, same result.
Thanks but...
letters_to_cleo said:
Hi there,
a. Yes, Stock GB's are generally safe
b. When your going to flash ROM, each ROM has it's own accompanying CWM.. so when your done choosing which ROM your going to flash your Note to, when your going to bootup in recovery.. and you get the standard CWMR...
c. Yes, Wiping is synonymous to doing the built-in factory reset on your phone (thru Settings), or the alternate way is to go to CWMR and wipe data. Different Methods, same result.
Click to expand...
Click to collapse
I am sorry but I am still a bit lost here. Before my N7000 I had a Samsung Skyrocket and flashed it using Odin from the GB that was on it to the stock ICS. I found several guides for this online and it worked fine and easily (although I still feared the brickbug). But this is basically all I know about this stuff.
So how do I flash something like Jelly Core? It sounds like I have to install some other was other than I did with Odin/stock ICS on my Skyrocket. Perhaps I need more of a tutorial on how to do this flashing of custom roms. Any suggestions?
I apologize to all for my thick-headedness.
the best and safest way first is to downgrade back to stock GB. Don't do any thing foolish by just flashing a stock ICS (with an unsafe kernel).
Downgrade first to stock GB and work your way up to eventually flash your preferred custom ROM (in cwmr or odin)

Categories

Resources