im using SGS III mini GT-8190 rooted
while using OTG-cable with mouse connected into it after battery dried out,i did the usual to make it back in charge mode
charge signal on but the % decreases no real charging happed
after a cuple of trys its completely go back in drain mode
its seems im stuck in some how programably and maybe hardware stuff
but im looking for software solution
most custom rom didnt change the man system file such i2c or ab8500-reg.0 which i think it comes with stuck room
cant get the USB cable work in Download Mode
however it works in normal mode "while android is running" and i could connect to odain as USB-debugge with COM port but stuck in
"setup connection..." and then "failed "
i had TWRP recovery
is there a way to break through .img file system so can be re-write through TWRP
or
How to convert ROM to be flashable from .tar.md5 ----- .zip
Related
Hi guys,
I have a problem.. my phone won't connect on the computer or with charger.
If i restart it, it just displays the battery and the spinner for a few seconds and then the screen goes black again and the process repeats over and over. I'm able though to get in download mode and flush successfully a stock firmware with odin.
As long as i keep it plugged on the computer it can connect with kies and recharge, once i unplug it won't connect again..
Can anybody help?
Thanks in advance.
well the fact that you can flash thru odin and connect with kies ect suggests its not a hardware fault...
perhaps you could try a (stock) firmware that contains all 3 files. and maybe flash it using pit and repartition... sounds like some sort of bug in the rom, confusing the phone when connected..........
just to make sure.. you have the latest drivers installed right ??
I've flushed JPO stock firmware, everything now works fine but it won't boot unless i connect it to the charger. It shows empty battery..
very strange..... are you running CWM if so boot into recovery and wipe battery stats.. then try charging the phone for a bit whilst it is switched off...
if it still fails to work properly then i must be wrong and it could be some sort of hardware fault... only samsung can repair that (unless you have insurance for a straight swap)
I wiped the battery stats but with no luck.. it didn't work.. I don't have insurance.. anyway, thanks for your help.
All i can say is that i have seen similar problems posted .Phone not working unless charger plugged in almost as if phone has lost the battery .
Dont know if problem was solved but a thought would be bad battery connections .
jje
basically i messed up the bootloaders now it does this (bear with me)
http://www.youtube.com/watch?v=QkFsZK79XYQ
it only does this when plugged into the wall and it will not do anything if plugged into usb port on the pc, my guess now is the battery is so flat that it wont do a thing any more! i almost got it to run via odin on the pc but the battery drained so bad that it wont respond, i have left it plugged in for at least 6 hours with then just the same response just on and off on and off.
can i take the battery out and charge it via a separate charger to get some life into it to then flash the stock rom via odin?
any ideas would be great! i don't mind taking it apart but don't want to if i'm going to fry the battery i have all sorts of wall chargers, can i join the + and - from the wall charger to the correct wires on the battery for it to charge? i have a multimeter to test the batteries voltage. any suggestions?
[UPDATE 1 ] flashed overcome stock rom then pc wont connect to odin even in recovery mode, :recovery is stock: :rom is stock: from the overcome website, cant flash any rom via odin as it wotn connect, error message usb device not recognised' how to fix this issue? maybe update.zip via sdcard within stock recovery? which rom and for gt-p1000 united kingdom. i tried to reinstall samsung kies for the correct driver but still the same issue, cannot connect after flashing. i have been following this guide http://p1000.teamovercome.net/?page_id=64 any help with connection would be great or flashing via recovery, almost unbricked but not quite.
my connection problem was due to a faulty usb cable, all is fixed now and i have overcome kratos.installed and running sweet
Hello, I don't think that you have a dead battery. I think your rom has a defect cause your Tab would like to boot. Is it possible to go to recovery or to the download mode? Try to flash something. Does your Tab start this screen flash automaticly by plug on a PC od starts this only if you try to turn it on?
PS: It is possible to remove the battery but it is a little difficult. My suggestion: don't touch the Battery
will not go to download mode or recovery. no response when pushing power power button, all i get is the flashing screen with pc and mobile phone connection.
i left tab connected to the pc for one hour, the tab came on with the pc-phone connection image, i flashed overcome rom via odin with repartition which completed but when it went to reboot it has stayed turned off and wont come on at all even when pressing the power button, no download mode and no recovery, i will wait again for it to come on and try the stock rom, not sure if i've got the correct bootloaders or not.
any ideas?
Have you tried leaving it on the ac outlet? or car charger?
ok slight update. . .
i left it plugged into the pc after it passed the odin flash it then BOOTED i was like WWWAAAAAAHHHHOOOOO bouncing on my chair and feeling very happy indeed the battery is totally dead but is now charging in the wall switched off to get some life back into the battery im so pleased
next steps is to get the overcome rom to flash!
lexriley said:
Have you tried leaving it on the ac outlet? or car charger?
Click to expand...
Click to collapse
i tried for 6 hours to plug it directly into the wall but nothing worked.
Exact same thing happened to me on the Sprint Tab. Called Samsung and sent the unit in. They sent me a brand new unit the next week.
when plugged into my pc now i get an error message, ' usb device has not been recognised' im thinking its the drivers but not sure where to get them, i have searched.
i have updated the 1st post with more information on this issue.
Your tab was showing a secondary bootloader so if you mess up your primary bootloader with the bootloader patch it'll still be recoverable and as for getting overcome I would recommend upgrading to gingerbread which doesn't have protected bootloaders and flash kratos or Jupiter which are faster than the froyo based overcome rims ;-)
Sent from my GT-P1000 using XDA Premium App
Roms*
Sent from my GT-P1000 using XDA Premium App
the only issue im having now is the fact that the pc wont recognise the android phone when in download mode.
the only message i get on the screen is 'usb device not recognised' i am then unable to flash a different rom or a stock rom via odin being gingerbread or froyo. thats why im asking if there is an update.zip file that i can flash from the recovery to make the usb mode work as it wont even work with debugging mode on or off and wont show via samsung kies or odin when the tab is booted.
my connection problem was due to a faulty usb cable, all is fixed now and i have overcome kratos.installed and running sweet
good troubleshooting!!! I
Sent from my GT-P1000 using XDA Premium App
ok first things first, imma noob, and i did a stupid thing.
It started in last summer when i wasnt able anymore to connect the N7000 to my WIN 7 64bit (probably after an update to ICS /JB).
Well since i never needed to transfer files (64GB-sdxc) i didnt care much about it. but then in last times my phone/ram cache was full of so much unblockable bootloaded crapware so that i wanted to switch from a official 4.1.2 firmware to cyanogen. But since my USB wasnt working it wasnt that easy.
Side note: the USB-port was ****ed up before (short-circuit, screen woke up due to fake-loading). i fixed that by luck and some dark magic.. so of course i thought the connection problem were because oif the broken jack.
The day before yesterday i tried for 8 hours anything i could find to install another bootloader and flash CM (CWM / TWRP / Triangle away / minimal adb/fastboot etc.); didnt work, CWM seemed to boot up but loading failed all the time at 1/3rd of the bar at screen went black.
Yesterday my friend came over and i tried to use his USB-jack to connect my phone to my Pc, which failed. THEN i put the "broken" one from mine in his N7000; that was efficacious, everything worked fine, so the USB-jack wasnt the problem.
Later i had, out of frustration, moronism, and anger, the glorious idea to download and flash another (older) Kernel via mobile odin to install an old gingerbread stock rom on it afterwards.
That was stupid as i know now, all i can do now is enter download mode, but without USB-connectivity and the stock bootloader with the options reboot system / update from sd / wipe data / wipe cache / test redbend fota(FS) and boot, which stucks at the N7000-screen.
After i managed to **** things up i found an article which describes my (now former) USB-problem perfectly. it says to put in a special number combination on the phone to get to phoneUtil and then switch from modem mode to pda mode. i knew this screen before but i couldnt find it at the preferences on JB.
Now comes my question: What could be done to unbrick my phone? is there any help?
Can you not try another USB cable? Try cleaning out the pins and see if it works. Then flash speedmod.
Sent from my GT-N7000 using Tapatalk
backstreetboy said:
Can you not try another USB cable? Try cleaning out the pins and see if it works. Then flash speedmod.
Sent from my GT-N7000 using Tapatalk
Click to expand...
Click to collapse
>Just to clarify: with USB-Jack i mean the USB-Port with the connector to the motherboard; sorry if i misused the word
I dont think so cause we used only his cable when he was here and my phone neither connected with mine nor with his USB-Jack, but both Jacks worked on his phone.
Pro-question: Is there a difference between (usual) USB-connection in booted mode and connection in download mode? i mean is download mode something like a "safe mode" where the USB doesnt need to run on 100% availabilty? Should i try to find the phone via Odin in downdload mode again by using his cable? i dont think this could work else.
Samsung galaxy note gt-n7000 bricked. Need HELP!!
The phone shows " Firmware upgrade issue encountered an issue. Please select recovery mode in Kies & try again". I cant go to recovery mode ie. vol up+home+power. THings I have tried:
1. with Kies the device isnt recognised. I have updated the driver as well.
2. with odin every thing fails... flashing "all samsung recovery.tar", flashing stock jelly bean, flashing .pit file
I have googled for days and tried many things but isnt working. Need help
im using SGS III mini GT-8190 rooted
while using OTG-cable with mouse connected into it after battery dried out,i did the usual to make it back in charge mode
charge signal on but the % decreases no real charging happed
after a cuple of trys its completely go back in drain mode
its seems im stuck in some how programably and maybe hardware stuff
but im looking for software solution
most custom rom didnt change the man system file such i2c or ab8500-reg.0 which i think it comes with stuck room
cant get the USB cable work in Download Mode
however it works in normal mode "while android is running" and i could connect to odain as USB-debugge with COM port but stuck in
"setup connection..." and then "failed "
i had TWRP recovery
is there a way to break through .img file system so can be re-write through TWRP
or
How to convert ROM to be flashable from .tar.md5 ----- .zip
mkr848 said:
im using SGS III mini GT-8190 rooted
while using OTG-cable with mouse connected into it after battery dried out,i did the usual to make it back in charge mode
charge signal on but the % decreases no real charging happed
after a cuple of trys its completely go back in drain mode
its seems im stuck in some how programably and maybe hardware stuff
but im looking for software solution
most custom rom didnt change the man system file such i2c or ab8500-reg.0 which i think it comes with stuck room
cant get the USB cable work in Download Mode
however it works in normal mode "while android is running" and i could connect to odain as USB-debugge with COM port but stuck in
"setup connection..." and then "failed "
i had TWRP recovery
is there a way to break through .img file system so can be re-write through TWRP
or
How to convert ROM to be flashable from .tar.md5 ----- .zip
Click to expand...
Click to collapse
Problem solved
By changing zenar diode ZD501 near usb ic switch
Thanks to me and friend who had the same device used for testing values
Hello everyone I am sure that there is a lot of this thread going.
But I think mine is even worse.
the problem:
I rooted the device, everything worked fine ( did it with card reader - because my pc can not recognize the device had the problem a long time ago, somehow it worked then, but does not now, giving me the code 10 and 43
I think my USB port on the SAMSUNG might be damaged, because it does recharge but wont connect at all, tried kies, tried all the debugging modes, drivers, turning off the computer, rebooting all that stuff..)
The main problem is I flashed the cwm, rebooted, worked fine, then I clicked the do Backup thing and from then I can only go to yellow "downloading" or samsung logo, cannot even use that "Odin" because my USB is apparently damaged.. Any Ideas at all other than taking the phone and throwing it into the dumpster?
it is gt-s5830
my system is Win7-64bit
any help will be deeply appreciated ...
sincerely Fariel2012
Samsung logo freeze, cant recovery, can download mode (cant join to pc)
try with different usb cable
daniga74
Fariel2012 said:
Hello everyone I am sure that there is a lot of this thread going.
But I think mine is even worse.
the problem:
I rooted the device, everything worked fine ( did it with card reader - because my pc can not recognize the device had the problem a long time ago, somehow it worked then, but does not now, giving me the code 10 and 43
I think my USB port on the SAMSUNG might be damaged, because it does recharge but wont connect at all, tried kies, tried all the debugging modes, drivers, turning off the computer, rebooting all that stuff..)
The main problem is I flashed the cwm, rebooted, worked fine, then I clicked the do Backup thing and from then I can only go to yellow "downloading" or samsung logo, cannot even use that "Odin" because my USB is apparently damaged.. Any Ideas at all other than taking the phone and throwing it into the dumpster?
it is gt-s5830
my system is Win7-64bit
any help will be deeply appreciated ...
sincerely Fariel2012
Click to expand...
Click to collapse
Hi there
you will need to give a usb jigg service to your device and then flsah it back to stock using odin
SGA s5830 stuck @ boot logo
I follwed these steps before it stuck @ boot logo
1 rooted phone through root_S5830.zip file
2 then used 6.0.4.6-cooper_fix.zip cwm recovery
3 decided to flash Touchwiz-Resurrected_ROM_V1.0.zip rom
4 followed all steps to flash thrrough CWM recovery
phone reebots samsung.com logo>> samsung boot animation shows up>>samsung name appears again keeps glowing and phone restarts!!!
after it I tried 6-7 different roms then i tried to flash through odin but wasnt able to do so but failed the device showed up in odin but wasnt able to flash stock rom
then i decided to go for Phil touch recovery I installed Philtouch recovery and tried to flash a custom rom now I'm stuck again at boot name GALAXY ACE s5830 nothing goes further!!!
I searched over XDA and some guy quoted this problem is solvable by using odin and putting phone in downloading mode (vol- button+home button + Power on ) I am able to put my phone in downloading mode, but when i conncet it to PC it says USB device not recognized WTF!!!!!???? 10 mins ago i connected my Phone using same cable same port same odin now this ***** appears ???
I swapped PC's, Cables, ports everything nothings working , phone wont start stuck @ boot logo pls help ASAP :crying:
That's it.. You have hard bricked your phone that's dead recovery and dead download mode. Give your phone the usb jigg service which will force it to go to either the download mode or the recovery mode whatever you want.