Hi! I have a old droid bionic, which may be hard bricked, but may just need a new recovery. About a month ago, i have safe strap running on it, and installed CM 10. then i was updating the safestrap, but got the wrong device version. Now all it does is boot the the safestrap screen, the goes blank for ever. I can get fastboot to work, as well as the default recovery.
Bottom line, is there a way to get a version of android back on here?
thx for all the help and devs!
Regards
Nvm, got it working again thru like 5 steps. Now have TWRP and CM 11!
I'm pretty sure so long as you can get fastboot enabled, you can fix almost any problem.
Related
First of all, I have checked around quite a bit on this forum as well as others to try and avoid having to ask a question that's already been answered. Here's my problem/ what happened. I was rooted (one-click with locked bootloader) and had tried out several roms for a couple of months now. A few days ago I reverted back to an old stock 2.2 backup. My phone received two ota updates and I'm pretty sure I lost root. I had just went on using the phone for about two days when I ran into a problem today. After shutting the phone off I have now become "stuck" at the initial "X" screen (not animated). I pulled the battery and tried again several times. I then tried to reboot into recovery from the bootloader/ 3 skateboards screen with no luck. Any time I hit recovery it simply takes me back to my stuck "X" screen. I have an entire backup of my SD card from earlier as well as at least 4 nandroid backups (one of which was the stock 2.2 before the latest ota). I am thinking I need to somehow put clockwork recovery back on my phone so I can restore to one of my backups. I do not know how to do this. Sorry for the lengthy post but I want to provide as much information as possible. Any help at all would be greatly appreciated.
Just like you restore to stock 2.2. You should have used recovery.img. use adb fastboot to put the stock or anom recovery. I am not am expert but I have had the same problem few times. Always use adb commands
Sent from my Nexus One using Tapatalk
Does my n1 have to be in usb debugging mode because it's acting like it's not connected or something. I get the message "error: device not found." I'm on the fastboot screen on my n1 and using terminal on a mac. I usually didn't leave debugging mode on
No it doesn't but you have to have the drivers installed as well as the SDK with dependencies.
Whew! Thank God! I ended up getting a FRG33 stock rom onto the sd card and the bootloader detected it. I'm not sure what happened but when I tried recovery after that it took me to the android with an "!" point (meaning no recovery?) and then back to the X. This time however it loaded on through and went right back to the way it was before it was stuck. Again, not sure what happened but thanks for the replies and help.
fastbook oem unlock
install Amon RA recovery
flash new rom.
Caseyp789 said:
Whew! Thank God! I ended up getting a FRG33 stock rom onto the sd card and the bootloader detected it. I'm not sure what happened but when I tried recovery after that it took me to the android with an "!" point (meaning no recovery?) and then back to the X. This time however it loaded on through and went right back to the way it was before it was stuck. Again, not sure what happened but thanks for the replies and help.
Click to expand...
Click to collapse
The exclamation mark is just the stock Android recovery - it was re-installed when you loaded the stock FRG33 ROM.
Performing OTA updates requires you to have the stock recovery installed. Simply reverting to a stock 2.2 nandroid isn't sufficient, so trying to install those OTAs (which should have failed without stock recovery) may have broken something there.
GldRush98 said:
fastbook oem unlock
install Amon RA recovery
flash new rom.
Click to expand...
Click to collapse
This is by far the easiest (and safest) way. Google/HTC provided us an easy and safe method for gaining full access to our phones.... Why so many people refuse to use it is beyond me. If you root it the proper way (with fastboot oem unlock), it will make recovery from any further issues a lot more simple.
From what I can tell, I am having the same symptoms as the topic creator. I believe the problems started during a failed flash of cyanogenmod 6, but I am not sure by what means the flashing took place.
I can't boot the phone normally, it hangs on the X splash screen and the same occurs when trying to enter recovery mode.
I have tried the passimg approach to fix this, it either doesn't recognize my zip or starts loading it and freezes on a loading bar.
Fastboot flashing recovery completes, but doesn't fix the issue.
I can fastboot flash every image partition except system or radio, both hang.
As danger rat and dude random both know, I have posted this problem on the nexus one forums but I thought I'd post here to have some more minds look at it.
Hello,
I have a nexus one that isn't working anymore. I was trying to install the cyanogenmod, but I guess I didn't do it correctly.
I was following the clockworkmod way from this: h t t p ://wiki.cyanogenmod.com/index.php?title=Nexus_One:_Full_Update_Guide
When flashing the rom something went wrong. After step 6 my phone didnt reboot, it just stayed off. Now it will only give me the nexus sign if i turn on the phone.
I can still acces the recovery menu when holding Power + volume down.
People told that I should go back to the stock rom.
Can anybody please help me?
*don't know if i've posted in the right category
When you get to recovery is it still clockwork or stock? If clockwork then try and flash cm6 again. If not you will have to download a stock rom push it to the sdcard as an update.zip and boot into the boot loader.
Sent from my Galaxy Tab, that makes phone calls
Since you can boot into recovery you have NOT bricked it for sure
As mentioned in the earlier post try to flash the CM ROM again
If you are unable to access the custom recovery (as in, the stock recovery is still in place), you can follow the manual instructions for installing ClockworkMod: http://wiki.cyanogenmod.com/index.php?title=Nexus_One:_Full_Update_Guide#Manual_Method
You can then follow the procedure for flashing the appropriate radio image: http://wiki.cyanogenmod.com/index.p...ll_Update_Guide#ClockworkMod_Recovery_process
And you can even install the ROM without using Rom Manager using this process: http://wiki.cyanogenmod.com/index.p...Update_Guide#Second_Method_.28via_Recovery.29
All of this is, as I'm sure you've noticed, posted on the same page that you linked. Hopefully this information will help you, now that you have been assured that your phone is not bricked.
Thanks for quick replies. I've contacted a guy with a lot of knowledge about these kind of thinks and helped me fixing me phone. I dont know exactly what went down but I will give it a try.
My first mistake was thinking that I rooted my phone (using the one click method). Don't know if thats the right way to do it, but in the end it wasn't rooted and I tought it was.
The guy rooted my phone, did the AmonRa recovery install and installed the Ethernom Rom for me. Great to have my phone back to working and great Rom btw.
Hi,
Full version as a note. Droid 1
Flashed clockworkmod recovery (2.5.0.1), went fine. Made a backup of stock rooted ROM, worked fine. Next flashed bugless beast .6, while clearing data & cache, no problem.
Now i want to flash to cm - trying out different ROMs - trying to reboot into recovery or flash another ROM both fail to get me to a bootloader. Instead i see the motorola boot logo for 30-45 seconds, followed by what looks like a regular boot (motorola M, then Droid eye, & booted.). I have also tried fixing permissions.
If anyone has any idea why this is happening or can direct me to a forum link it would be greatly appreciated. Sorry if this is in the wrong section, and yea I've tried looking through the forums for a while.
Thanks
just a little baby sized pump...
This happened to me too after working perfectly for several months. All of the sudden I just couldn't get to clockwork. I am running CM7 Nightlies. After not being able to fix the issue for several days I decided that a full wipe via the .sbf method was in order. I've got everything up and running again but it was an annoying process. Can anyone out there help us to understand why this happened so we don't have to deal with this again?
Do you have a link for the method you described about? That would be really helpful!
An ever so slightly larger bump
I really am not trying to be lazy, but all the .sbf methods I've read so far seem require you getting to a boot loader. If I could get to a boot loader this wouldn't be a problem, as I made a back up of my stock ROM. I have a functioning bugless beast ROM, just no recovery / boot loader, and no way to flash back to my recovery.
And possibly solved..
One: Please pardon my ignorance, doing these things on my Eris was far easier, or at least what I got used to.
Two: Please also ignore the word boot loader in my previous posts, as it was the recovery console that I could not get to load. Sorry Again.
Three: Its magically working. My methods were unscientific to say the least, but the Droid is now in "ClockworkMod's Recovery v2.5.0.1".
Things I finally did:
NOTE - I DO NOT BELIEVE ANY OF THIS TO BE THE PROPER ORDER OF THINGS. PLEASE VERIFY WITH SOMEONE FAR MORE INTELLIGENT THAN ME. THE FOLLOWING REFLECTS THE PROCESS I DID, AND SHOULD PROBABLY NOT BE FOLLOWED UNLESS A MOD ACTUALLY SAYS THIS WAS CORRECT
1. Pulled Battery, hold power button down for a few seconds, and then put back in
2. Hold Up on D-pad while holding the Power Button
3. You see the following
Code:
bootloader 2c.7c
battery ok
ok to program
connect usb
data cable
4. Connect USB data cable to PC running RSD Lite. You will also want a .sbf recovery file from a trusted source.
5. Select the .sbf in RSD Lite. Tell it to start. I used the clockwork recovery only .sbf
*** Where things got officially weird for me ***
6. The .sbf file I told it to load seemed to work, as the progress bar moved. The phone almost instantly rebooted, back to the ROM I was running minutes earlier. Clockwork had not been working previously trying to reboot into recovery, but almost instantly upon trying this time, I was in recovery mode.
NOTE - The USB cable was still plugged in as well. I don't know which combination of things actually got this to work, but it did.
Hope this helps someone else out.
[SOLVED -- Read my last post]
Posting on forum was my last resource, but I've tried literately almost everything I can possible find.
I already bricked my phone and had to unbrick, do everything (update firmware etc) all over again.
I am at a point where I am afraid to do something new to my phone now without knowing what they are...
Please bare with me, I am not familiar with exactly what flashing is or whatnot, I just followed the instructions and got where I am....
K, recently I decided to wipe my phone CLEAN and update to new CyanogenMod 9 from factory mode.
So, I have Captivate, I897. It was ECLARE with 2.1 firmware.
I have updated to 2.3.5 (Gingerbread [I897UCKJ2]), Rooted.
I had to Flash BACK to KK4_stock_kernel.tar for me to use WIFI again because I had issue after Rooting my phone, I couldnt access the WIFI.
I installed Clockwork mod (Free version).
My goal is to install CyanogenMod 9, and part of the process requires me to enter the CMW Recovery Mod.
I dont even know what this looks like, but all I know is whenever I boot my phone, after the AT&T logo animation it seems to go into this "messed up" screen, where as if my phone is broken. Stays there for 3 seconds and then continues to boot back to its OS.
In ROM manager, it says Flash ClockworkMod Recovery (You must have the clockworkmod recovery installed to flash and restore ROMs!)
Another option within ROM manager is, Reboot into Recovery (Boot into Recovery mode for manual management.), which if I do access it, it takes me back to that AT&T logo animation and that "messed up" screen again, but this time it stays there. Where all kinds of colored pixels are on my screen as if my screen is broken. It will only continue to boot back to my OS if I press power button or some sort.
Im guessing that's my Recovery Mod, which my phone for some reason cannot see?
So I tried "Download ROM (Upgrade to ROM Manager (premium) to access the full list of ROMs!", hoping this may cure that messed up screen effect, which I think is the Recovery Mod for all I know... When I click to install, it gives me Confirm Phone Models. None are my phone model for me to install.. (It only gives me Google Nexus S / Google Nexus S 4G / Samsung Epic4G / Samsung GalaxyS i9000).
Earlier, I was looking at this, http://forum.xda-developers.com/showthread.php?t=1127578
which is a way to fix recovery mod(?) But I have NO idea how to even install those files... Maybe not the .tar file but the other one.
Please help? Am I the only one experiencing this kind of problem? Couldnt find anywhere else on youtube / google / forum..
Thank you VERY much in advance, really appreciate it..
-Dan.
danroh said:
I had to Flash BACK to KK4_stock_kernel.tar for me to use WIFI again because I had issue after Rooting my phone, I couldnt access the WIFI.
-Dan.
Click to expand...
Click to collapse
This is your likely problem right here. The Kernel that is installed during the rooting process and typically when you install custom roms is what is responsible for installing and therefor you being able to access the CWM recovery. Flashing back to the stock kernel likely messed things up for you.
http://forum.xda-developers.com/showthread.php?t=1300843
Now if you follow that link it will take you to several one click options for flashing your phone to stock gingerbread but with a kernel containing CWM. Also keep in mind that it is possible you could have wifi issues if you've had them in the past, but if your goal is to get to CM9 just ignore the wifi for the time it shouldn't be an isuse in the end.
Hey OP,
See this.... TRusselo's Flashing Guide
Sent from my SAMSUNG-SGH-I897 using xda premium
You need Gingerbread bootloaders.
Thanks guys! I figured out the problem and solved it!
Like you guys said, I didnt have the bootloader. The gingerbread I installed was the no bootloader version. After reinstalling to the one with bootloader, I was able to access the recovery mod and that "rainbow screen" glitch was no more.
Thank you!
Droid 4 running Stock Jb 4.1.2, Safestrap 3.11, Liquid smooth 2.9, CM (last stable)
Everything working fine for a number of months, installed Liquid smooth via -> delete romslot 3, create romslot 3, install Liquid 2.8.
It ran for a number of days no problems. Restarted fine, all features worked great, even the annoying random restart from 2.4 went away.
6 - 10 days in, im surfin' the news sites at work, put it down, screen goes black, i pick it up. Hit the power button cause i realize its off and it just boot loops... so bad i had to vol-/+ pwr, go to flash mode and THEN turn it off b/c it just kept trying to restart, hang on logo.
I got home and decided to AP flash the latest:
9.8.2O-72_VZW-18-2
Blur_Version.98.72.182.XT894.Verizon.en.US for the maserati.
Boot looped a few times, i was able to get it to go into recovery mode, after that it loaded up the stock JB system. First boot it crashed and restarted, second boot it loaded but only the keyboard worked, not the touch screen. Went to the in OS option of factory reset mode + delete storage.
Rebooted, worked. Checked it a few boots, everything is fine. I use Druid 4 Utility Xt894 JB version and apply the root. Works great. Install safestrap, Create new partition, install liquid smooth 2.9. Works for an afternoon... at work today the touch screen stops responding, i restart it a few times. I try to enter recovery mode. Now im in boot loop again...
I've tried re flashing it again, a few times. I tried even going down to the previous release of JB for the phone. STILL 4.1.2!!!! But nothing.... it just boot loops... what did i do wrong? It was running great. No tweaks or anything done to it prior to it having its melt down.
Help please.. ive provided as much information as possible and though i only joined XDA now to post for help, i have read it for a long time as my main source for my phone and have donated to both CM and Liquidsmooth teams previously..
help!!!
I can't see where you are doing anything wrong. You have obviously done your research and have a good idea of what you are doing. I see, after you fastbooted, you went back to Liquid. I think I would try running CM10.1 or even stock for a few days and see if you have the issue there as well. If you do than it sounds to me like it might be a hardware issue. If not, maybe try re-downloading Liquid. Perhaps your zip got corrupted somehow.
I would love too. In fact i would be willing to run it on the stock crappy 4.1.2 if i could get it out of boot loop this time...
It just keeps boot looping on the logo. AP Fashboot flash and BP flash work but recovery and normal boot/reboot mode just goes into M logo boot loop.
I've re downloaded the 4.1.2 jb SBFs from 2 different sources to ensure its not a corrupt file, tried 18_1 and 18_2 software versions...
Is there a way to use the abd shell to get into the filesystem and check whats going on? Is the SBF the last call? or is there another route to see whats going on or just flash EVERYTHING? Like completely back to stock?
I can find my way around a PC file system but im not familiar with linux. Please help me understand, Is it like having CMOS and BIOS settings or equivalent to damaged CMOS firmware? What am i not replacing/reverting by SBF and HOW can i replace/revert BEYOND the basic sbf...
If ya point me in a direction or to someone who can help me out i can do all the foot work just point me in the right direction?
Is this applicable? I found a site talking about using CWM in a ADB shell file push to possibly get access to more features?
The article also goes into reading the busybox / ADB command screen? (sorry for not proper jargin) and see what its doing during the boot loop before it restarts?
Id add the link but i need more posts....
Update: Flashed 18_2 again with a "factory cable" i made, let it boot loop a series of times before it started up into the stock system again.
At first, again the touch screen wouldn't work, random lockups and restarts, etc. Since i just got it into the main system again and i had to leave for the weekend for a trip(no wifi or network), i couldn't mess with it all weekend but i left it on the whole time and kept checking its functionality... gradually its come back to full function. Touch screen works and is accurate, no more lockups, no more restarting, even stopped boot looping when i restart and enter recovery..
Im not sure and i couldn't find any forum converstations or write ups to support to idea but i think after a major crash and you flash new or reflash your SBF, it seems the phone needs time to recalibrate and index? Not sure, but just an FYI. Gonna try loading SS and liquid again.