[Q] bluetooth phonebook sync problem - Xperia Z1 Q&A, Help & Troubleshooting

Hi all,
i got a problem with my bluetooth phonebook sync. My phone connects via blutooth to the car, but the phone book does not sync. The request for the transfer of the phone book does not appear at all.
I have this Problem with following ROMs:
Sony Stock 4.3 (14.2.A.0.290)
IHackers 2.1 (JellyBean 4.3)
SlimKat 4.4
However, no problems with these ROMs,
Sony Stock 4.2.2 (14.1.G.2.257)
FreeXperia CM11 (fxp / kali)
What can cause this and how can I solve this problem for the other roms?
Thank you
Sony xperia Z1 C6903
Opel UHP car kit

You can flash the "Baseband" only from 14.1.G.2.257 on 14.2.A.0.290 or Update to .136. If .136 will not solve this problem then flash Baseband here too from .257.

I have the same problems with 290 and 136.. Does this mean that I can flash the 136 generic BALL ftf and then just flash the baseband from 257? It won't screw the phone up will it?
Regards,
Alan

nalab1 said:
It won't screw the phone up will it?
Click to expand...
Click to collapse
I can't guarantee that but this was confirmed by users who did that to improve the signals on they phone. They flashed baseband from 4.2.2 FW .257 on 4.3 FW .290 and it worked. Flashing anything its a risk so be careful, BTW, if this will not work you can flash the baseband from 4.3 FW .136 back, in the same way. If I am not wrong, if so someone correct me please, the baseband contain all package of frequency for the phone to work properly.

eclyptos said:
I can't guarantee that but this was confirmed by users who did that to improve the signals on they phone. They flashed baseband from 4.2.2 FW .257 on 4.3 FW .290 and it worked. Flashing anything its a risk so be careful, BTW, if this will not work you can flash the baseband from 4.3 FW .136 back, in the same way. If I am not wrong, if so someone correct me please, the baseband contain all package of frequency for the phone to work properly.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you for your reply.. So, does the baseband contain all of the wireless stuff like wifi, bluetooth etc?
To get the sequence right I -
1) Completely flash .136 - reboot to check if ok
2) Flash the baseband ONLY from .257 - reboot to check if ok
If, the phone were to get stuck in say, a bootloop is there any way to completely power it off and then reflash?
Regards,
Alan

nalab1 said:
Hi eclyptos,
Thank you for your reply.. So, does the baseband contain all of the wireless stuff like wifi, bluetooth etc?
Click to expand...
Click to collapse
It should.
nalab1 said:
To get the sequence right I -
1) Completely flash .136 - reboot to check if ok
2) Flash the baseband ONLY from .257 - reboot to check if ok
Click to expand...
Click to collapse
Yes.
nalab1 said:
If, the phone were to get stuck in say, a bootloop is there any way to completely power it off and then reflash?
Regards,
Alan
Click to expand...
Click to collapse
Of curse but it will not stuck.
@chunlianghere already did this HERE and will report leater.

eclyptos said:
It should.
Yes.
Of curse but it will not stuck.
@chunlianghere already did this HERE and will report leater.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you. For my information (sorry for the noobness!) if it were stuck in a bootloop how do I actually power the phone off?
Regards,
Alan

nalab1 said:
Thank you. For my information (sorry for the noobness!) if it were stuck in a bootloop how do I actually power the phone off?
Click to expand...
Click to collapse
Power + Volume Up. BTW, Flash with fully charged battery.

eclyptos said:
Power + Volume Up. BTW, Flash with fully charged battery.
Click to expand...
Click to collapse
Hi eclyptos,
Thank you for your replies and help. I am going to try this at the weekend as during the week, I work away from home and dont have access to my pc. I will let you know how it goes.
Regards,
Alan

eclyptos said:
You can flash the "Baseband" only from 14.1.G.2.257 on 14.2.A.0.290 or Update to .136. If .136 will not solve this problem then flash Baseband here too from .257.
Click to expand...
Click to collapse
I have tried this, but i did not work.
Any other advise?

Yocto69 said:
I have tried this, but i did not work.
Any other advise?
Click to expand...
Click to collapse
Are you saying that after flashing baseband from .257 on .136 you still have problems? Try downgrade the entire system and check if the problem persist. Sometime is not the phone but the other devices so really we can try looking forever.

eclyptos said:
Are you saying that after flashing baseband from .257 on .136 you still have problems? Try downgrade the entire system and check if the problem persist. Sometime is not the phone but the other devices so really we can try looking forever.
Click to expand...
Click to collapse
Look in the op. I have tried several Firmwares and Roms.
If i downgrade to. 257 It works perfect!
The other Device is not the problem.
Thx

Yocto69 said:
Look in the op. I have tried several Firmwares and Roms.
If i downgrade to. 257 It works perfect!
The other Device is not the problem.
Thx
Click to expand...
Click to collapse
Other than that can be a kernel.

eclyptos said:
Other than that can be a kernel.
Click to expand...
Click to collapse
Is it maybe possible to take a blutooth.apk from .257 and use it on .290?

Yocto69 said:
I have tried this, but i did not work.
Any other advise?
Click to expand...
Click to collapse
it works fine when listening music.
but during voice call, its not ok.

Yocto69 said:
Is it maybe possible to take a blutooth.apk from .257 and use it on .290?
Click to expand...
Click to collapse
Is not that easy. Bluetooth is not an application which you can download or install. It's implemented in the system and baseband. The main reason for bad quality like WiFi, Mobile Signal or Bluetooth is the Radio which is the Baseband in Z1. On HTC for example to improve the reception for all of them I am able to flash just the Radio.

eclyptos said:
Is not that easy. Bluetooth is not an application which you can download or install. It's implemented in the system and baseband. The main reason for bad quality like WiFi, Mobile Signal or Bluetooth is the Radio which is the Baseband in Z1. On HTC for example to improve the reception for all of them I am able to flash just the Radio.
Click to expand...
Click to collapse
Ok, i have tried severall kernel.
ihackers advanced kernel, stock kernel and doomlords kernel. All on 4.3 roms. => No change.
What else could I try?

Yocto69 said:
Ok, i have tried severall kernel.
ihackers advanced kernel, stock kernel and doomlords kernel. All on 4.3 roms. => No change.
What else could I try?
Click to expand...
Click to collapse
I losing ideas, I don't want to say but at last it may be a hardware issue but not sure. I don't know if you want to do this but you should go back to Stock and Flash a Stock FTF to check if the problem persist even there, is it does it's the phone.

Related

[Q] Downgrade from 4.4.2 KK - 4.3 JB. Help.

First of all, I've tried searching and reading tons of forums/guides the past hours, but I can't get this to work. So please excuse me if I've missed something
I'm trying to downgrade my Xperia Z1 from (the horrible) KK update 4.4.2. to my stock 4.3 JB. I've tried flashing the following FTF's:
C6903_14.2.A.1.136_Generic Nordic NCB_1276-9897.ftf
C6903_14.2.A.0.290_Customized NCB 1276-9897 (Nordic Combined).ftf
C6903_14.1.G.1.534_1276-4314_R2A.ftf
All found here!
No one works. I keep getting bootloops (I can se the startup animation, then it restarts). I manged to get my phone working with using the orginal KK FTF (C6903_14.3.A.0.681_Generic NCB 1276-9897 (Nordic).ftf).
Could somebody please help me and figure out what the problem is? I've added my Software Info as an attachment.
Thanks for any replies!
Really weird, if you flashed them correctly from Flashtool v0.9.15 they should work, check the version of your Flashtool if is correct. Also try the one (FW .534) provided by NUT for C6903, here.
eclyptos said:
Really weird, if you flashed them correctly from Flashtool v0.9.15 they should work, check the version of your Flashtool if is correct. Also try the one (FW .534) provided by NUT for C6903, here.
Click to expand...
Click to collapse
I used Flashtool Version 0.9.15.0. and yes, I believe so.
Flashmode->Choose FTF->Wipe Appslog and Cache, uncheck Data->Flash
That looks like 4.2. FW, and a custom ROM? I would like to have the original 4.3 .
DCWolfie said:
That looks like 4.2. FW, and a custom ROM? I would like to have the original 4.3 .
Click to expand...
Click to collapse
Yes, but if that will work then you will have more chance to Update via Flashtool to .136 FW 4.3 and maybe get Root too (Optional).
---------- Post added at 02:59 AM ---------- Previous post was at 02:57 AM ----------
DCWolfie said:
Flashmode->Choose FTF->Wipe Appslog and Cache, uncheck Data->Flash
Click to expand...
Click to collapse
BTW, if you still have problems then you have to wipe Data too, it may be the issue.
eclyptos said:
Yes, but if that will work then you will have more chance to Update via Flashtool to .136 FW 4.3 and maybe root too (Optional).
Click to expand...
Click to collapse
Hm.. I'm not sure about a custom ROM, It's a road I'm not quite familiar with, if you understand .
There isn't any troubleshooting I could do that you can think of? Have i selected the right FTF for my phone? Is it actually possible to downgrade from 4.4.2. to 4.3?
EDIT:
If I'm going to delete my data, exactly WHAT am I losing? I want to know what I have to take backup of before trying that out.
DCWolfie said:
Hm.. I'm not sure about a custom ROM, It's a road I'm not quite familiar with, if you understand .
Click to expand...
Click to collapse
It's not Custom, it's Stock, they are all Stock, but you can have Root on it.
DCWolfie said:
There isn't any troubleshooting I could do that you can think of? Have i selected the right FTF for my phone? Is it actually possible to downgrade from 4.4.2. to 4.3?
Click to expand...
Click to collapse
Yes, it is possible, I did many times. Check everything you downloaded or did, nobody can know that better than you-self.
DCWolfie said:
EDIT:
If I'm going to delete my data, exactly WHAT am I losing? I want to know what I have to take backup of before trying that out.
Click to expand...
Click to collapse
OK, then, wipe everything and make a fresh installation of 4.3, I think this will work. Backup anything what is important to you, Pictures, Vids, or Data games to not going to download them again. I don't know, wipe everything..
HELP ME..
Hello to alls.. really need help here.. I'm a new user of Z1. Buy Z1 phone yesterday and really impress on previous adroid 4.3 version..
After upgrade to kitkat its start to annoying me.. so i start to google about this problems. now i know it was happen by kitkat.
i dont know how to do a flash.. which flash tool are suittable for Z1 right now?
i search for my country firmware on xda.developer and i could't find it..
i really want to get rid this kitkat off from my z1..
PLEASE HELP ME...
customization version - 1276-7939-R3C
sorry about my poor english.. :smileyexclaim:
malamiaoki said:
Hello to alls.. really need help here.. I'm a new user of Z1. Buy Z1 phone yesterday and really impress on previous adroid 4.3 version..
After upgrade to kitkat its start to annoying me.. so i start to google about this problems. now i know it was happen by kitkat.
i dont know how to do a flash.. which flash tool are suittable for Z1 right now?
i search for my country firmware on xda.developer and i could't find it..
i really want to get rid this kitkat off from my z1..
PLEASE HELP ME...
customization version - 1276-7939-R3C
sorry about my poor english.. :smileyexclaim:
Click to expand...
Click to collapse
You will find all on XDA just by searching the right Words.
You have to use "Flashtool v0.9.16", download the FTF from "Mega Collection" for your Model (C6902/3/6). Download the FTF "Generic" or "Commercial", the customization have nothing to do with that, put that FTF in the Folder of Flashtool, Run Flashtool, Flash, select the right FTF, put your Phone in "Flashmode" and when Flashtool asking connect the phone via USB to PC, Wipe everything Data, Cashe, Appslog. Done.
Do not ask for step by step, all what you have to know I already wrote.
Clik Thanx.

[Q] help please please please

please help, after i update my XZ to 4.4.2 (.230) my phone always says that headset is connected even there is no headset, my speaker is not working anymore, i dont know what to do, please help,
mgraycv said:
please help, after i update my XZ to 4.4.2 (.230) my phone always says that headset is connected even there is no headset, my speaker is not working anymore, i dont know what to do, please help,
Click to expand...
Click to collapse
Do a factory reset
St.Jimmy90 said:
Do a factory reset
Click to expand...
Click to collapse
it will go back to 4.3?
mgraycv said:
it will go back to 4.3?
Click to expand...
Click to collapse
it will return the phone to factory settings.
don't worry it wont go back to 4.3
androidtweaker1 said:
it will return the phone to factory settings.
don't worry it wont go back to 4.3
Click to expand...
Click to collapse
still no sound T_T
mgraycv said:
still no sound T_T
Click to expand...
Click to collapse
Okay you can manually flash 4.3 ftf and check whether this issue is rectified if not then it may be an hardware issue
If its sorted then manually flash 4.4.2 ftf after 4.3
use flash tool to flash firmware
Your speaker is OK
Don't panic
Check if there is anything inside the headset jack because the phone thinks that you have plugged in a headset and disables the speaker
So Check the Headset jack maybe for water damage or anything lodged in there
Good Luck!
androidtweaker1 said:
Okay you can manually flash 4.3 ftf and check whether this issue is rectified if not then it may be an hardware issue
If its sorted then manually flash 4.4.2 ftf after 4.3
use flash tool to flash firmware
Click to expand...
Click to collapse
I already did that, after i flash to 4.3 my speaker works fine, but when i flash back to 4.4, there is no sound again,
Sorry with my poor english,
berezker said:
Your speaker is OK
Don't panic
Check if there is anything inside the headset jack because the phone thinks that you have plugged in a headset and disables the speaker
So Check the Headset jack maybe for water damage or anything lodged in there
Good Luck!
Click to expand...
Click to collapse
My headset jack is clean and clear, i am getting very frustrated >.<
mgraycv said:
I already did that, after i flash to 4.3 my speaker works fine, but when i flash back to 4.4, there is no sound again,
Sorry with my poor english,
Click to expand...
Click to collapse
Try a different generic version of 4.4.2
androidtweaker1 said:
Try a different generic version of 4.4.2
Click to expand...
Click to collapse
I think i almost tried every generic version, hehe, even stock rom, both .227 and .230,
mgraycv said:
I think i almost tried every generic version, hehe, even stock rom, both .227 and .230,
Click to expand...
Click to collapse
You can root by downgrading to 4.2 after that you can flash a pre rooted 4.4.2 rom and check

after the update...

Hello there,
After i updated with NUTS release, the update pops up again even tho i updated it. What could possibly be the problem?
Any help is greatly appreciate it. Thanks in advance
samircali said:
Hello there,
After i updated with NUTS release, the update pops up again even tho i updated it. What could possibly be the problem?
Any help is greatly appreciate it. Thanks in advance
Click to expand...
Click to collapse
is your bootloader unlocked???
if its thats the problem if not just reflash the newest firmware available for your device
TheHunk_2 said:
is your bootloader unlocked???
if its thats the problem if not just reflash the newest firmware available for your device
Click to expand...
Click to collapse
No, my boatloader is not unlocked. It shows that i have the 4.4.4 installed in my setings. Do i have to flash the ftf file again. I dunno what to do.
samircali said:
No, my boatloader is not unlocked. It shows that i have the 4.4.4 installed in my setings. Do i have to flash the ftf file again. I dunno what to do.
Click to expand...
Click to collapse
what is your device model number?
c6903 ,c6902 or what?
TheHunk_2 said:
what is your device model number?
c6903 ,c6902 or what?
Click to expand...
Click to collapse
My device mobile number is C6903. Is there hope to fix this. Maybe NUT uploaded the wrong ftf or the flashible zip.
samircali said:
My device mobile number is C6903. Is there hope to fix this. Maybe NUT uploaded the wrong ftf or the flashible zip.
Click to expand...
Click to collapse
Every problem can be solved.BUT DEATH :laugh:
Im c6903 too. im not having this problem im on this firmware http://dfiles.ru/files/tqsgjp29m
download it check your pc for the drivers and stuff and flash it .Don't forget to wipe the appslog cache and data
if still having the same problem then this is your best shot http://www.xperiablog.net/2014/08/0...rtified-for-xperia-z1-z-ultra-and-z1-compact/
TheHunk_2 said:
Every problem can be solved.BUT DEATH :laugh:
Im c6903 too. im not having this problem im on this firmware http://dfiles.ru/files/tqsgjp29m
download it check your pc for the drivers and stuff and flash it .Don't forget to wipe the appslog cache and data
if still having the same problem then this is your best shot http://www.xperiablog.net/2014/08/0...rtified-for-xperia-z1-z-ultra-and-z1-compact/
Click to expand...
Click to collapse
Is it with root or without root
You don't need root to flash the firmware just search abour it in Google you'll find everything you need.
TheHunk_2 said:
You don't need root to flash the firmware just search abour it in Google you'll find everything you need.
Click to expand...
Click to collapse
Yes, but I dont want to lose root. My phone is rooted with NUTS version since the beginning. This is the first time Im getting this problem.
Thanks anyway
samircali said:
Yes, but I dont want to lose root. My phone is rooted with NUTS version since the beginning. This is the first time Im getting this problem.
Thanks anyway
Click to expand...
Click to collapse
flash the firmware then root it with easyrooting kit and towlroot

Z1 Unknown IMEI, Baseband, IP, and MAC [SOLVED]

I understand there is already a post regarding another user who has had this problem. However, I believe that my circumstances differ.
I am currently running iHacker's 4.1 rom. My device is a c9603, and has an unlocked bootloader. (I'm not sure if the other user was locked or unlocked)
From the roms that I have tested, I am only able to successfully use wifi and see my baseband, etc., using PAC or a restoration of a backup made of my current rom. All I am trying to do is update from .757 to .108.
Would it be worth it to make a backup of everything, relock the bootloader, revert it completely back to stock, unrooting it, and then either root it again and try to update, or use sony's PC companion or my phone's update center to update my firmware and then root it on .108?
Thanks in advance. This has just been a persistent problem and I'm really getting tired of it.
***UPDATE***
Somewhere in all my rom flashing endeavors, I must have accidently picked up a c6903 version of a ROM or ftf. It changed the model number (according to the status in the service menu) to an 03. Something told me to pop the sim tray, and behold: Model number c6902. Flashed the correct version, and my wifi is up and running again!
Try to go back to initial firmware and then to .108
olokos said:
Try to go back to initial firmware and then to .108
Click to expand...
Click to collapse
Nothing seems to be working. No matter what I flash, I loose my baseband, imei, mac, ip... The only two roms that have worked are my current one and PAC.
What the hell is going on?
Try to flash full .534 FTF
It will bring back your IMEI and baseband. I have that before (lost IMEI) then flash .534, install recovery then flash straight to .108
Alright. I have class right now, but I'll give it a try when I get home.
Sent from my C6903 using xda premium
So... Apparently flashing anything below .757 causes my phone to bootloop... Help?
Flash everything on .534 FTF (baseband, kernel, system, ta, all of them) and all wipe to....
Use latest FlashTool (.18)
BlackSoulxxx said:
Flash everything on .534 FTF (baseband, kernel, system, ta, all of them) and all wipe to....
Use latest FlashTool (.18)
Click to expand...
Click to collapse
I am I think... I can try again. I'll let you know how it goes.
BlackSoulxxx said:
Flash everything on .534 FTF (baseband, kernel, system, ta, all of them) and all wipe to....
Use latest FlashTool (.18)
Click to expand...
Click to collapse
I'm still getting a bootloop. I get past the Sony and Xperia screen and then it gets stuck mid-loop of little animation they included. Could it be a broken ftf? Or just an error when I downloaded it? Because more than one of the ftf files do this.
ShadowTech13 said:
I'm still getting a bootloop. I get past the Sony and Xperia screen and then it gets stuck mid-loop of little animation they included. Could it be a broken ftf? Or just an error when I downloaded it? Because more than one of the ftf files do this.
Click to expand...
Click to collapse
Reflash FTF again then wait for 30mins (phone is plug into charger too)....
BlackSoulxxx said:
Reflash FTF again then wait for 30mins (phone is plug into charger too)....
Click to expand...
Click to collapse
Sorry for all the trouble, but I will try again as soon as I get home. It's about time this damn problem gets solved.
ShadowTech13 said:
Sorry for all the trouble, but I will try again as soon as I get home. It's about time this damn problem gets solved.
Click to expand...
Click to collapse
Nope, same exact thing happened. Except this time, I only got to the "Xperia" portion of the boot logo before it decided to do another boot-loop. I waited for 30 minutes, and had it plugged in, but still nothing...
This time throw it at Sony centre to fix it....We have no idea.....

C6903 - Baseband Unknown Fix

Hi Experts,
I have searched the forum and after flashing for three sleepless nights, I am still struck with the unknown baseband issue.
The details are:
C6903
BL Unlocked & now its locked using Flashtool (DRM or TA backup is unavailable )
Currently the phone is struck in boot loop in .534
Used Flashtool ver. 0.9.22.3 & 0.9.18.6
Latest EMMA & Xperia Companion
My phone hanged when listening to the music and when I force restarted the unknown baseband showed up. While flashing I got the baseband back after flashing .518 however it hanged again after two days and I lost the BB
Now I am struck in boot loops on .534 and .518 both. I can boot into .290 successfully. Can someone please guide me to the correct method of restoring my IMEI permanently.
P.S. As per my short experience with C6903, I believe something stops the boot of .534 and .518 after first boot. Means I was not able to boot into .534 but accidentally when I flashed .518, my phone booted successfully. However now I am unable to boot into .518. May be I am missing the piece of puzzle that an expert can provide.
Thanks in advance~
D-r-e-a-m-e-r said:
Hi Experts,
I have searched the forum and after flashing for three sleepless nights, I am still struck with the unknown baseband issue.
The details are:
C6903
BL Unlocked & now its locked using Flashtool (DRM or TA backup is unavailable )
Currently the phone is struck in boot loop in .534
Used Flashtool ver. 0.9.22.3 & 0.9.18.6
Latest EMMA & Xperia Companion
Thanks in advance~
Click to expand...
Click to collapse
hi , read here and try reflash use [NUT]'s 14.1.G.1.534 FTF , hope its help.
iedafarha said:
hi , read here and try reflash use [NUT]'s 14.1.G.1.534 FTF , hope its help.
Click to expand...
Click to collapse
Thanks for your tip but I have already tried and still get struck in bootloop.
No .534 FTF has booted until now and I have used 6 of them already...
An update is that I have rooted 4.4.4 and installed recovery...
can someone tell me where can I get .534 zip to flash as the files I have are giving me verification error on TWRP.
Thanks in advance...
I have tried to use NUT fix but the files are not available for downloading.
I would really appreciate if someone can direct me to the correct path. I am almost giving up now...
http://forum.xda-developers.com/showthread.php?t=2687443
D-r-e-a-m-e-r said:
I have tried to use NUT fix but the files are not available for downloading.
I would really appreciate if someone can direct me to the correct path. I am almost giving up now...
http://forum.xda-developers.com/showthread.php?t=2687443
Click to expand...
Click to collapse
May be file deleted , other options you can create flash zip using PRFCreator , search and download ftf file from here .
iedafarha said:
May be file deleted , other options you can create flash zip using PRFCreator , search and download ftf file from here .
Click to expand...
Click to collapse
Hi again, Really appreciate your help.
I have tried flashing a number of files but still in vain. What I really can't understand is .518 was the last 4.2.2 rom that booted successfully on my phone and brought my baseband back. Now .534 and .518 are both ending in a bootloop at Sony animation Really driving me crazy...
As a side note, can you tell me if the modem files in the link below are useful for this issue?
https://github.com/SonyAosp/vendor_qcom_firmware/tree/n/honami/C6903
By the way I am really amazed with the Z1 ability to handle abuse that I have thrown at it during the last 2 weeks
Changing phone is not an option for me right now. Using Nokia 1100 after a long time seems very uncomfortable and can't do it for long
D-r-e-a-m-e-r said:
By the way I am really amazed with the Z1 ability to handle abuse that I have thrown at it during the last 2 weeks
Changing phone is not an option for me right now. Using Nokia 1100 after a long time seems very uncomfortable and can't do it for long
Click to expand...
Click to collapse
Anyone please...
Experts plzzz...
D-r-e-a-m-e-r said:
Experts plzzz...
Click to expand...
Click to collapse
I am still looking for a solution to install JB without bootloop
Bump...
D-r-e-a-m-e-r said:
I am still looking for a solution to install JB without bootloop
Click to expand...
Click to collapse
Lol why jb. Don't you want KitKat lollipop??
Heck even nougat with unlocked bootloader
gauravbhakuni90 said:
Lol why jb. Don't you want KitKat lollipop??
Heck even nougat with unlocked bootloader
Click to expand...
Click to collapse
I need to fix my baseband issue. That can only be done with JB.
D-r-e-a-m-e-r said:
I need to fix my baseband issue. That can only be done with JB.
Click to expand...
Click to collapse
You can flash Baseband even from lollipop ftf.
gauravbhakuni90 said:
You can flash Baseband even from lollipop ftf.
Click to expand...
Click to collapse
Thx for the tip but its not working.
My SIm was only detected once thats when I installed .518 but it lasted for a day and got held. When I force restarted the phone it was again missing baseband.
Now it isnt booting into .518 or .534.
Experts am I asking something that is un-do-able...
Guys shall I give up fixing this phone
I loved this dead beauty...
Hi, tried to flash with different cables as I don't have Sony original cable with me but the results are still the same. No luck with .534 and baseband is still unknown...
I understand this is a free community and people are free to determine if they wanna help someone or not. However I just wanna know if this is repairable or shall I just forget about repairing it. Any inputs will be highly appreciated.
D-r-e-a-m-e-r said:
Hi, tried to flash with different cables as I don't have Sony original cable with me but the results are still the same. No luck with .534 and baseband is still unknown...
I understand this is a free community and people are free to determine if they wanna help someone or not. However I just wanna know if this is repairable or shall I just forget about repairing it. Any inputs will be highly appreciated.
Click to expand...
Click to collapse
I have realized that the phone does not shuts down with the power button in any bootable rom. Also sometimes the baseband does appear soon after installation but it disappears as sim is inserted. Can someone plz help me understand whats going wrong. I really love this phone...

Categories

Resources