Related
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Bluffer said:
Hello,
I have some problems trying to flash my XZ. I'm using Xperia Flashing Tool 0.9.10.2 beta6 on Windows 8 x64 and whenever I try to flash my XZ flashing tool "gets stuck at "Device connected in flash mode" message after which it gets reconnected and if I try again same thing will happen.
So my question is, am I doing something wrong and if so, please advise.
Click to expand...
Click to collapse
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Maddhouse said:
have you correctly installed the drivers for it, connect phone in flashmode and does windows drivers load, also in flashtool go to devices>conected devices and what does it say
Click to expand...
Click to collapse
I think drivers are installed fine. Screenshot is below.
no doesnt look it, under ADB devices there is no device, Reinstall drivers and try again. Try the way in my sig for win 8
Unfortunately same thing happens - check screenshot below.
Bluffer said:
Unfortunately same thing happens - check screenshot below.
Click to expand...
Click to collapse
thats better you now have a ADB device installed, you should now be able to put your phone into flashmode
power off your phone with usb diconnected, hold vol down and reconnect turned off phone to usb and you should now get green led and flashtool will say device connected in flashmode but you only have about a min in flashmode before phone reboots
Thank you for your help and effort but even now it keeps disconnecting device. I don't know where the problem is, maybe I'm not doing something as I should.
This is the procedure I was trying:
1) I select Flash device in flash tool
2) I select Flashmode mode
3) I choose which firmware to flash and click Flash so flash tool can start it's magic
4) When flash tool shows message that I can remove my device from USB and turn it off I do so
5) I also press volume down and reconnect the device with the PC.
6) Problem happens here
what about if flashtool isnt ready to flash file, does flashtool pick it up (4 and 5)
it will say device connected in flashmode with green led
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Bluffer said:
Yeah, it does pick it up and displays a message "Device connected in flash mode" and after awhile "Device disconnected".
Click to expand...
Click to collapse
good yer i think its about a min, now try and download another FTF file
part 1
part 2
that works i have got loads of people to flash that
edit: i made it so its self extract version then there is a FTF file for flashtool
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Bluffer said:
As you suggested the problem was in faulty FTF. It's working like a charm now!
Thank you once again!
Click to expand...
Click to collapse
Good Good, What wasnt helping was you didnt have drivers installed aswell, now you just have to root and your sorted :highfive:
hey i m having same with my x8 after i accidently kept stock rom for nalf kernal... nw i m nt able to open cmw in phone...plz help..
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally corrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
wmiswm said:
I am in an awkward situation.
xperia z, 4.2.2 244 rooted stock rom, bootloader locked, usb debug mode off, recovery not installed.
I accidentally disrupted build.prop and the phone bricked.
I cannot use flashtool to flash the stock rom back because usb debug mode is off.
I cannot use Sony update service Pro to force update because it said that "your phone already has the latest available software installed".
I cannot use PC Companion to repair because the software said that "Sony update engine doesn't have software available for your phone".
Please help.
Click to expand...
Click to collapse
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
YudiA1 said:
Use PC companion but try use repair phone not update. Wait till all phone model showing up than choose your model phone. btw, your phone must off.
than follow instruction there... wil take 1~2 hour for repair.
Hope you can solve your problem. ill take screen shoot when im home later than post here..
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Thank you very much for your reply. But I am already using the PC Companion repair option, and the response is as stated above.
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Reply
wmiswm said:
I cannot use flashtool to flash the stock rom back because usb debug mode is off
Click to expand...
Click to collapse
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
gm007 said:
flashtool is all what you need,read the instructions
http://forum.xda-developers.com/showthread.php?t=2240614
Sent from my C6603 using xda premium
Click to expand...
Click to collapse
many thanks, done.
shysparrow said:
You can use Flashtool to flash stock rom, doesn't matter if usb debug mode is on or off (only needed to install recovery or to root)
Download stock rom, install flashtool + drivers and follow screen instructions.. Good Luck! :good:
Click to expand...
Click to collapse
yes, you are right. Yesterday I check everything on the right panel and it does not work. Today I leave all option unchecked and flash properly. Many thanks anyway.
maxam73 said:
J have the same problem, yesterday j installed cyanogenmod, now xperia Z was on SONY logo and j can't flash original firmware on flashtool, j can only flash original kernel, but is still on sony logo
SUS says that hasn't new firmware for my phone.
What can j do ????
Thanks in advance
Click to expand...
Click to collapse
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
wmiswm said:
Just follow the flashtool instruction and re-flash the stock rom first, everything will return to unroot stated. Reroot then and try again.
Click to expand...
Click to collapse
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
maxam73 said:
Maybe j have other kind of problem, j tried with flashtool but it doesn't start flashing when in flashmode, after a minute phone boots itself continuosly on sony logo.
j tried several times with different PC and different ftf file.
j hope to solve this problem, but how...
Click to expand...
Click to collapse
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
YudiA1 said:
Try this way bro.. Done in many Xperia here..
Solving Bootloop phone/Flash Tool can't Detect your phone.
Your Phone Must Off!! and not connected !!
1. Open Pc Companion
2. Click update on Red ellipse (in Picture 1)
3. Start on Phone/tablet Update (in Picture 2)
4. Click Repair on Next Screen
5. in Next Screen, Read that warning Click Continue if you OK
6. Next Step click on Red Circle than Next...
7. Wait initializing Software (10~30 mnt) or depend your ISP speed
8. After initializin9 All Xperia Phone List Will Show Up.
Choose What Xperia Phone Will you repair ( I choose XZ) than Next..
9. Follow instruction On picture.
( Connect USB on your Phone while Press Vol down )
10. if not Start.. Unplug usb and try plug again ==> same no 9)
11. After start.. Waiting 1~2 Hours till done.
(Read Warning There )
Sent from my C6602 using xda premium
Click to expand...
Click to collapse
Solved...j know that phones must be off, the problem was flashtool, j used other version (beta 4) on other pc running xp instead of win7 and all goes good.
Thanks to all for helping me
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
theVenerable said:
Doesnt work.
I cant use flashtool, period.
Are there anyother methods?
Click to expand...
Click to collapse
The above didn't work for me because I received error based on my type of phone.
This guide however did help: http://forum.xda-developers.com/showthread.php?t=2240614
I had to reboot windows to a settings to enable unsigned drivers. Installed Flashtool and it's drivers,
First unlocked the bootloader(BLU button, got the IMEI, used the sony form (http://unlockbootloader.sonymobile.com/instructions))
Then I downloaded the stock sony xperia z ftf image, placed it in Flashtool's firmware folder, then flashed it (flash device > flash mode).
Now my phone's working again.
HTH,
George
brick,unbrick,xperia z problem,flashtool
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
shayanster said:
My OS phone in recovery mode (root) got deleted And when I turn on phone stuck on Sony logo And when it is connected to the computer showing error your USB not recognized and Flash mode for use Flashtool doesn't work and the same error shows what should i do?
Click to expand...
Click to collapse
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
visualfighter said:
If you still can enter custom recovery, you only need flash rom and (with) suitable kernel.
If not, you need Flashtool.
- make sure you have the newest version of flashtool and driver
- connect your phone to pc.
- when computer show error about usb not recognized, go to computer management - device manager. Find something in universal serial bus controller list that have yellow triangle and exclamation mark. right click and remove it
- disconnect your phone then reboot your pc
- install flashtool and driver, reboot pc again
- connect your phone to pc. Now, it should detect your phone.
- do flashing procedure
cmiiw
Click to expand...
Click to collapse
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
shayanster said:
Thanks for the answer I tried all ways but the problem is not solved .I think the only solution is JTAG box
Click to expand...
Click to collapse
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
androidtweaker1 said:
To use Flashtool put phone in flashmode, it will not work in recovery mode
To put phone in flashmode
Hold power + both volume keys
wait till you feel three vibrations.
Make sure you have installed Z drivers flashmode drivers & fastboot drivers(Setup fille is in driver folder of flashtool)
Keep FTF file in firmware folder of flashtool
Start flashtool
Click the thunder button
select flashmode
select the FTF file
When it tells you to connect phone
Hold volume down key and connect USB it should start flashing
Click to expand...
Click to collapse
when it is connected into flashmode the computer showing error your USB not recognized
shayanster said:
when it is connected into flashmode the computer showing error your USB not recognized
Click to expand...
Click to collapse
Is it Windows 7 or 8?
My sony xperia z will not power on anymore. If i connect it to a charger, it shows the sony logo and keeps restarting. When i connect it to my computer not much happens. SUS can detect it and i tried updating it, it downloads and installs and tells me to restart my phone but still nothing happens and the same thing as before happens when i connect it with a charger.Sony PC Companion app does not detect the phone.
So i tried flashing with xperia flasher and i downloaded a 4.3 stock rom, flashed it but then at the end it says usb debugging mode must be enabled but i do not think its enabled, nor can i check since my phone does not power on.
Please Help!!!
HPTL7 said:
My sony xperia z will not power on anymore. If i connect it to a charger, it shows the sony logo and keeps restarting. When i connect it to my computer not much happens. SUS can detect it and i tried updating it, it downloads and installs and tells me to restart my phone but still nothing happens and the same thing as before happens when i connect it with a charger.
So i tried flashing with xperia flasher and i downloaded a 4.3 stock rom, flashed it but then at the end it says usb debugging mode must be enabled but i do not think its enabled, nor can i check since my phone does not power on.
Please Help!!!
Click to expand...
Click to collapse
Hi, was it a stock rom on it before this issue occured?
gaza1994 said:
Hi, was it a stock rom on it before this issue occured?
Click to expand...
Click to collapse
Yes. Stock rom and also never been rooted.
bump
HPTL7 said:
Yes. Stock rom and also never been rooted.
Click to expand...
Click to collapse
Did you try to hard reset it? Try to press power and vol up.
What to you mean with xperia flasher? Download a .ftf file and use flashtool
St.Jimmy90 said:
Did you try to hard reset it? Try to press power and vol up.
What to you mean with xperia flasher? Download a .ftf file and use flashtool
Click to expand...
Click to collapse
sorry meant FlashTool. i did flash and it completed it successfully but when i tried powering on, nothing happend. so i connected to charger and the sony logo loop restart happen again. it said at the end of flashing that usb debugging must be enabled so i think that may be the problem why it did not work.
I have tried hard reset. It vibrates once, pauses and then vibrates 3 times and then nothing.
HPTL7 said:
sorry meant FlashTool. i did flash and it completed it successfully but when i tried powering on, nothing happend. so i connected to charger and the sony logo loop restart happen again. it said at the end of flashing that usb debugging must be enabled so i think that may be the problem why it did not work.
I have tried hard reset. It vibrates once, pauses and then vibrates 3 times and then nothing.
Click to expand...
Click to collapse
What if you open pcc, select repair phone and follow the steps on screen? (your phone has to be powered off)
St.Jimmy90 said:
What if you open pcc, select repair phone and follow the steps on screen? (your phone has to be powered off)
Click to expand...
Click to collapse
Thanks for the reply but as stated earlier in my first post, i said that pc companion does not detect my phone.
HPTL7 said:
Thanks for the reply but as stated earlier in my first post, i said that pc companion does not detect my phone.
Click to expand...
Click to collapse
I know, but I wasn't sure if you tried it with the repair method. If you just plug your phone in to the pc, it won't recognize it. But when you use the repair method, pcc tells you to power off the phone, and bring it into flashmode
St.Jimmy90 said:
I know, but I wasn't sure if you tried it with the repair method. If you just plug your phone in to the pc, it won't recognize it. But when you use the repair method, pcc tells you to power off the phone, and bring it into flashmode
Click to expand...
Click to collapse
when i do it pcc tells me to connect a phone.
HPTL7 said:
when i do it pcc tells me to connect a phone.
Click to expand...
Click to collapse
When I open up pcc and select "Support Zone" - "phone / tablet software update" - "repair phone" it'll ask what phone you have, then you select it, it will download the firmware and ask you to power off the phone and plug it in while holding vol up
St.Jimmy90 said:
When I open up pcc and select "Support Zone" - "phone / tablet software update" - "repair phone" it'll ask what phone you have, then you select it, it will download the firmware and ask you to power off the phone and plug it in while holding vol up
Click to expand...
Click to collapse
Sorry my bad. You were right.
However i don't think i had a repair option. It is currently downloading a firmware i think.
I'll keep you updated.
Thanks a lot.
HPTL7 said:
Sorry my bad. You were right.
However i don't think i had a repair option. It is currently downloading a firmware i think.
I'll keep you updated.
Thanks a lot.
Click to expand...
Click to collapse
No worries, if this doesn't work try again with flashtool, and select everything at wipe
St.Jimmy90 said:
No worries, if this doesn't work try again with flashtool, and select everything at wipe
Click to expand...
Click to collapse
It did not work.
How do i try that repair thing you mentioned?
HPTL7 said:
It did not work.
How do i try that repair thing you mentioned?
Click to expand...
Click to collapse
nvm, found out how to do it. Completed it but it still does not work.
Is it cause i need at least 50% battery? If so, is there any way of doing so? because if i connect to wall charger it does the sony logo restart loop and when i connect to pc it goes in mtp mode.
HPTL7 said:
nvm, found out how to do it. Completed it but it still does not work.
Is it cause i need at least 50% battery? If so, is there any way of doing so? because if i connect to wall charger it does the sony logo restart loop and when i connect to pc it goes in mtp mode.
Click to expand...
Click to collapse
I don't think it's because of your battery level..... I'm sorry, but I can't help you on that....
I think you have to send it to sony for repair. As long as you haven't modified anything on your phone they should repair it
Edit: Before you send it to sony, try their chat, sometimes they can help
Your bootloader is unlocked? And have you tried flashing ftf using flashtool?
Sent from my C6603 using Tapatalk
pjgowtham said:
Your bootloader is unlocked? And have you tried flashing ftf using flashtool?
Sent from my C6603 using Tapatalk
Click to expand...
Click to collapse
I am not sure whether my bootloader is unlocked or not. is there anyway i can check?
HPTL7 said:
I am not sure whether my bootloader is unlocked or not. is there anyway i can check?
Click to expand...
Click to collapse
If you dont know bootloader unlock, its most probably its locked. Grab an ftf and flash with flashtool. Usually update service works.
Sent from my C6603 using Tapatalk
I have done that before so that means it should be unlocked.
Now what do i do?
Hello. I'm trying to root my device by downgrading it first. So i need to flash the rom. I had my phone in flashmode. But in a minute or two the phone will wake up. And i can't continue my flashing because of that. Anyone know supposed to be the problem? Sorry im noob at this stuff
Don't connect ur phone in flash mode until flash tool asks for it. The moment flash tool indicates u to connect ur device on, only then connect it in flash mode. Once u load the ftf in flashtool, it takes a min to process the files after which it notifies for u to connect ur phone. Cheers
Sent from my C6603 using XDA Premium 4 mobile app
dj_richard05 said:
Don't connect ur phone in flash mode until flash tool asks for it. The moment flash tool indicates u to connect ur device on, only then connect it in flash mode. Once u load the ftf in flashtool, it takes a min to process the files after which it notifies for u to connect ur phone. Cheers
Sent from my C6603 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Ohhhh. Thanks. But i got this error.. -_-
The error is ERROR - Processing of loader.sin finished with errors.
n0p4rk1ng said:
Ohhhh. Thanks. But i got this error.. -_-
The error is ERROR - Processing of loader.sin finished with errors.
Click to expand...
Click to collapse
Damaged file! Re-download :good:
reptile64 said:
Damaged file! Re-download :good:
Click to expand...
Click to collapse
Yeah i did redownload it. It's still the same. My XZ is 10.4.B.0.101 and i'm trying to downgrade it to 10.3.1.A.2.67. And my device is 4.3. Don't know if it's the firmware that i'm downgrading or what..
Next time please post in the Q/A section which is DIRECTLY BELOW the general section.
Also tagging a post as a question in the general section will bring up a prompt telling you it doesn't belong here if i recall correctly..
n0p4rk1ng said:
Yeah i did redownload it. It's still the same. My XZ is 10.4.B.0.101 and i'm trying to downgrade it to 10.3.1.A.2.67. And my device is 4.3. Don't know if it's the firmware that i'm downgrading or what..
Click to expand...
Click to collapse
Download the ftf from other place. Maybe the site you downloaded from has uploaded a damaged ftf:
And for your first problem try reinstall flashtool and when the device turn on when you in flashmode hold vol+ and power button for 15 seconds
Hope that helped:angel:
guys i was trying to restore the ta backup to relock the bootloader. after it was done it tried to restart the phone and after the shut down the phone was hard bricked !
unfortunately i was about to recover it so I followed this thread : http://forum.xda-developers.com/showthread.php?t=2646405
but i had a problem during the flashing
i get this error after some proceeds :
MINOR ERROR [0x80080021_, err:0017 ]
error while uploading final HDR block
break
finished
anyone knows what to do now?
Guys pleeaaaassseeeee i need a hand over here help me ;( ;(
Do not bump a thread within 24 hours.
Download a stock ftf and flash it using flashtool
Sent from my C6903 using XDA Premium 4 mobile app
gregbradley said:
Do not bump a thread within 24 hours.
Download a stock ftf and flash it using flashtool
Sent from my C6903 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
give me a break! man! thanks for noticing! i know how to flash a ftf file.. the phone is dead totally. no flash mode or fastboot mode
It already happened to me, you just have to flash again your phone with your computer and it work (for me).
megavigore said:
It already happened to me, you just have to flash again your phone with your computer and it work (for me).
Click to expand...
Click to collapse
no way man!its not a soft brick! you cant use flash mode or fastboot mode . just emergency mode ! and thats not working for me neither.
dont know what to do... seems its dead
What is emergency mode?
If there is no response then stick it on charge for 24 hours, do not touch it then try flashing a stock FTF again
Greg is trying to help you mate.
And he's right, there's a time difference and you have to wait for guys to see your thread...
Check do you have latest flashtool
Check do you have correct drivers
Check is your ftf corrupted (download a new one)
, hard restart your device (vol up+power).
Open flashtool and hit start, wait till flashtool prepares fw and ask you to connect device.
Then connect device.
If that won't work, try to download another ftf file...
Maybe you have corrupted ftf and that's causing a problem...
Sent from my D6503 using Tapatalk
funky0308 said:
Greg is trying to help you mate.
And he's right, there's a time difference and you have to wait for guys to see your thread...
Check do you have latest flashtool
Check do you have correct drivers
Check is your ftf corrupted (download a new one)
, hard restart your device (vol up+power).
Open flashtool and hit start, wait till flashtool prepares fw and ask you to connect device.
Then connect device.
If that won't work, try to download another ftf file...
Maybe you have corrupted ftf and that's causing a problem...
Sent from my D6503 using Tapatalk
Click to expand...
Click to collapse
thanks to everyone here who is trying to help me out . but guys, i'm having no flashmode no fast boot mod..i know how to flash a ftf..but this one is different! there is nothing except of a red blinking led.. its hard braked! it will not show anything when i connect to pc. no Power+vol up works. it connect just when you connect the testpiont to GND and some stuff to get connected in emergency mode...
when i connect it normally no log adds in flashtool or any sound on windows..
NiM72NiK said:
thanks to everyone here who is trying to help me out . but guys, i'm having no flashmode no fast boot mod..i know how to flash a ftf..but this one is different! there is nothing except of a red blinking led.. its hard braked! it will not show anything when i connect to pc. no Power+vol up works. it connect just when you connect the testpiont to GND and some stuff to get connected in emergency mode...
when i connect it normally no log adds in flashtool or any sound on windows..
Click to expand...
Click to collapse
Uff...
Are you sure you restored right/yours TS backup?
I have a friend who restored Z1 TA backup to Z2, this things happen so who knows...
It's really odd if you restored your backup on stock fw and something like that happened..
Now I realized you wrote "I had flashtool problems..."
I thought you have problems in flashtool now, that's why I said try with another ftf or another flashtool version...
If you got that, and you did, while you were flashing ftf....I believe you are, unfortunately, right, this is hard brick.
BTW - which firmware you tried to flash?
Sent from my D6503 using Tapatalk
funky0308 said:
Uff...
Are you sure you restored right/yours TS backup?
I have a friend who restored Z1 TA backup to Z2, this things happen so who knows...
It's really odd if you restored your backup on stock fw and something like that happened..
Now I realized you wrote "I had flashtool problems..."
I thought you have problems in flashtool now, that's why I said try with another ftf or another flashtool version...
If you got that, and you did, while you were flashing ftf....I believe you are, unfortunately, right, this is hard brick.
BTW - which firmware you tried to flash?
Sent from my D6503 using Tapatalk
Click to expand...
Click to collapse
i was un iHackers 4.2 using doomkernel v21 tried to relock the bootloader( I have done that before) but this time it tried to restart but this happnd after the restart process..
seems it done, right?
NiM72NiK said:
i was un iHackers 4.2 using doomkernel v21 tried to relock the bootloader( I have done that before) but this time it tried to restart but this happnd after the restart process..
seems it done, right?
Click to expand...
Click to collapse
you need to be on a stock kernel if you relock the bootloader.
You should have flashed a stock FTF immediately after relocking and before restarting.
The solution is to flash a stock FTF
and you have not done this yet
gregbradley said:
What is emergency mode?
If there is no response then stick it on charge for 24 hours, do not touch it then try flashing a stock FTF again
Click to expand...
Click to collapse
please charge it for 24 hours without touching it, then try again
coming back to this thread. Wondered if all was well - ended well or still stuck ?
I tried to install magisk using bridge approach
and ended up with something that will get to just bluelight ( flashboot ?) mode . I am downloading a stock T-Mob FTF. J-FYI this is an operator locked boot loader. I dunno - is it poss to permanently unlock it and install Cust ROM ? I want to :
-- Recover my data from the dead prev . install
--Have a ROM ( stock or custom ) with Magisk installed.
My plan :
-- Flashtool install 4.4 FTF
-- _______________ <----- Need help here. How do I get magisk working ?
Note that AFAIK for locked bootloader , /system is RO